®

Bayhydrol U 2750

Characterization Aliphatic, hydroxyfunctional polycarbonate ester-polyurethane dispersion,

cosolvent-free.
Binder for the formulation of water-reducible 2K-PUR coatings.
Form supplied approx. 41 % in water / DMEA (approx. 58 : 1)

Specification
Property Value Unit of measurement Method
Viscosity 100 - 1,500 mPa·s DIN 53019
-1
at 23 °C, (D = 40 s )
Non-volatile content 39 - 43 % DIN EN ISO 3251
(1 g / 1 h / 125 °C)
pH supply form 7.0 - 9.0 DIN ISO 976

Specific Properties • Very good weathering resistance

• Hard-elastic and scratch-resistant films
• Good adhesion on plastics
• Solvent-free

Other data*
Property Value Unit of measurement Method
Acid number (solid resin) 25.0 - 29.0 mg KOH/g DIN EN ISO 2114
Density at 20 °C approx. 1.06 g/ml DIN EN ISO 2811
OH content (solid resin) approx. 3.6 %
*These values provide general information and are not part of the product specification.

page 1 of 4
Edition 2022-01-05

Replaces edition dated 2015-09-01 Product Datasheet

 ®
Bayhydrol U 2750

Properties / Applications ®
Bayhydrol U 2750 is a hydroxyfunctional polycarbonate ester-polyurethane
dispersion which can be thinned with water to application
viscosity. In combination with hydrophobic polyisocyanates (e.g.
®
Desmodur ultra N 3600, N 3900) and/or with hydrophilic polyisocyanates
(e.g. Bayhydur ultra 304, ultra 305, XP 2655) high performance,
hard-elastic two-component polurethane-hydrocoatings can be formulated.
®
Two-component polyurethane hydrocoatings based on Bayhydrol U 2750
are characterized by high weathering resistance (gloss-retention, resistance
to cracking), good appearance (high gloss, low haze value) and very high
reflow-behavior after dry- or weet-scratching.
®
Bayhydrol U 2750 is compatible with various polyacrylic dispersions (e.g.
®
Bayhydrol A 145, A 2470, A 2601, A 2845, A 2695, A 2770). On account of
the many potential co-reactants, compatibility testing should always be carried
out.
Cleaning After use, formulation and application equipment should be cleaned
immediately or left to soak in water. Warm water, alkaline cleaning agents or
alkaline isopropyl alcohol are suitable for cleaning.

page 2 of 4
Edition 2022-01-05

Replaces edition dated 2015-09-01 Product Datasheet

 ®
Bayhydrol U 2750

Storage - Storage in original sealed Covestro containers.

- Recommended storage temperature: 5 - 30 °C.

- Protect from frost, heat and foreign material.

General information: The product is sensitive to frost. Prologed freezin can

damage the product irreversibly. Prolonged storage at higher temperatures
may result in a decrease of viskosity and/or an increase of average particle
size, possibly resulting in sedimentation of coagulation.
The viscosity of the product is largely governed by the pH. As the pH may
decrease during storage, a decrease in viscosity is also to e expected. The
viscosity can be restored to its original value by the addition of small amounts
of an aqueous 10 % solution of dimethyl ethanol amine.
Contamination with certain bacteria, fungi or algae may render the product
unusable.
Storage time Covestro represents that, for a period of six months following the day
of shipment as stated in the respective transport documents, the product
will meet the specifications or values set forth in section "specifications or
characteristic data" above, what ever is applicable, provided that the product is
stored in full compliance with the storage conditions set forth in and referenced
under section "storage" above and is otherwise handled appropriately.
The lapse of the six months period does not necessarily mean that the product
no longer meets specifications or the set values. However, prior to using said
product, Covestro recommends to test such a product if it still meets the
specifications or the set values. Covestro does not make any representation
regarding the product after the lapse of the six months period and Covestro
shall not be responsible or liable in any way for the product failing to meet
specifications or the set values after the lapse of the six months period.

page 3 of 4
Edition 2022-01-05

Replaces edition dated 2015-09-01 Product Datasheet

 ®
Bayhydrol U 2750

Labeling and statutory requirements This product data sheet is only valid in conjunction with the latest edition of the
corresponding Safety Data Sheet. Any updating of safety-relevant information
– in accordance with statutory requirements – will only be reflected in the Safety
Data Sheet, copies of which will be revised and distributed. Information relating
to the current classification and labeling, applications and processing methods
and further data relevant to safety can be found in the currently valid Safety
Data Sheet.

The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal, written
or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative
that you utilize our products, technical assistance, information and recommendations to determine to your own satisfaction whether our products,
technical assistance and information are suitable for your intended uses and applications. This application-specific analysis must at least include
testing to determine suitability from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by
Covestro. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which are available
upon request. All information and technical assistance is given without warranty or guarantee and is subject to change without notice. It is expressly
understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in connection with
the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized and shall not
bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to any material
or its use. No license is implied or in fact granted under the claims of any patent.
This product is not designated for the manufacture of a medical device or of intermediate products for medical devices1). [This product is also not
designated for other specifically regulated applications (e.g. including cosmetics, plant protection, fertilisers, plant strengtheners, food processing, food
contact and others). If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices or
for other specifically regulated applications Covestro must be contacted in advance to provide its agreement to sell such product for such purpose.]
Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food
Contact products or cosmetic applications must be made solely by the purchaser of the product without relying upon any representations by Covestro.
1) Please see the "Guidance on Use of Covestro Products in a Medical Application" document.
Edition: January, 2018
Editor: Coatings, Adhesives & Specialties
Covestro Deutschland AG
Kaiser-Wilhelm-Allee 60 Contact:
51373 Leverkusen,Germany CAS Single Point of Contact APAC
www.covestro.com e-mail: [email protected]
page 4 of 4
Edition 2022-01-05

Replaces edition dated 2015-09-01 Product Datasheet