VHF Marine Transceiver: S-14720XZ-C1 Apr. 2011
VHF Marine Transceiver: S-14720XZ-C1 Apr. 2011
S-14720XZ-C1
Apr. 2011
INTRODUCTION
TRANSMIT SUPPLIED
MODEL VERSION
POWER CHARGER
USA 5W BC-199SA
IC-M24
EXP 5W
CHN 5W
BC-199SE
EUR-1 5W
EUR 5W
IC-M23 UK 5W –
FRG 5 W (1 W)
BC-199SE
HOL 5W
AUS 5W BC-199SV
CAUTION
(IC-M24)
Be sure to include the following four points when ordering 1. Make sure that the problem is internal before dis-
replacement parts: assembling the transceiver.
2. DO NOT open the transceiver until the transceiver is
1. 10-digit Icom part number disconnected from its power source.
2. Component name 3. DO NOT force any of the variable components. Turn them
3. Equipment model name and unit name slowly and smoothly.
4. Quantity required 4. DO NOT shor t any circuits or electronic par ts. An
insulated tuning tool MUST be used for all adjustments.
<ORDER EXAMPLE> 5. DO NOT keep power ON for a long time when the
1110003491 S.IC TA31136FNG IC-M23 MAIN UNIT 5 pieces transceiver is defective.
6. DO NOT transmit power into a Standard Signal Generator
8820001210 Screw 2438 screw IC-M24 Top cover 10 pieces
or a Sweep Generator.
7. ALWAYS connect a 30 dB to 40 dB attenuator between
Addresses are provided on the inside back cover for your
convenience. the transceiver and a Deviation Meter or Spectrum
Analyzer, when using such test equipment.
8. READ the instructions of the test equipment throughly
before connecting it to the transceiver.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia and/or other countries.
TABLE OF CONTENTS
SECTION 1 SPECIFICATIONS
M IC-M23 M IC-M24
D GENERAL D GENERAL
• Frequency coverage : Transmitting 156.000–161.450 MHz • Frequency coverage : Transmitting 156.025–157.425 MHz
Receiving 156.000–163.425 MHz Receiving 156.050–163.275 MHz
• Mode : FM (16K0G3E) • Mode : FM (16K0G3E)
• Antenna impedance : 50 Ω (nominal) • Antenna impedance : 50 Ω (nominal)
• Power supply requirement : BP-266 only (3.7 V DC nominal; negative ground) • Power supply requirement : BP-266 only (3.7 V DC nominal; negative ground)
• Current drain (approximately) : TX (5 W/1.0 W/0.5 W) 2.3 A/0.9 A/0.7 A • Current drain (approximately) : TX (5 W/1.0 W) 2.3 A/0.9 A
Maximum audio 0.35 A typical Max. audio 0.35 A typical
Power save 8 mA typical Power save 8 mA typical
• Frequency stability : ±1.5 kHz • Frequency stability : ±10 ppm
• Operating temperature range : –15°C to +55°C • Operating temperature range : –20°C to +60°C; –4°F to +140°F
• Dimensions : 58.5 (W) × 128.5(H) × 34.5(D) mm • Dimensions : 58.5 (W) × 128.5(H) × 34.5(D) mm
(Projections not included) (projections not included) 2.3 (W) × 5.6 (H) × 1.3 (D) inch
• Weight : Approximately 260 g • Weight : Approximately 260 g; 9.2 oz
(including battery pack, antenna, belt clip) (including battery pack, antenna and belt clip)
D TRANSMITTER D TRANSMITTER
• Output power : 5 W (approx.; High)/1 W (Low)/0.5 W (E_Low)* • Output power : 5 W (approximately; High) and 1 W (Low)
*1 W (High) and 0.5 W (Low) for German • Modulation system : Variable reactance frequency modulation
version, depending on the pre-programmed • Maximum frequency deviation : ±5 kHz
setting • Adjacent channel power : 70 dB
• Modulation system : Variable reactance frequency modulation • Spurious emissions : –68 dBc typical
• Maximum frequency deviation : ±5 kHz • Residual modulation : 40 dB
• Adjacent channel power : 70 dB • Audio frequency response : +1 dB to –3 dB of 6 dB oct. from 300–3000 Hz
• Spurious emissions : 0.25 µW
• Audio harmonic distortion : 10% (at 60% deviation)
• Residual modulation
• Audio frequency response
: 40 dB
: +1 dB to –3 dB of 6 dB oct. from 300–3000 Hz
D RECEIVER
• Receive system : Double-conversion superheterodyne
• Intermediate frequency : 1st 21.7 MHz, 2nd 450 kHz
• Sensitivity (12 dB SINAD) : 0.25 µV typical
D RECEIVER • Squelch sensitivity : 0.35 µV typical (at threshold)
• Receive system : Double-conversion superheterodyne • Intermodulation : 70 dB typical
• Intermediate frequency : 1st 21.7 MHz, 2nd 450 kHz • Spurious response : 70 dB typical
• Sensitivity (20 dB SINAD) : –4 dBµ emf typical • Adjacent channel selectivity : 70 dB typical
• Squelch sensitivity : –5 dBµ emf typical (at threshold) • Audio output impedance :8Ω
• Intermodulation : 68 dB • Audio output power : 0.6 W typical (at 10% distortion)
• Hum and noise : 40 dB
• Audio frequency response : +1 dB to –3 dB of –6 dB oct. from 300–3000 Hz
• Spurious response : 70 dB
• Adjacent channel selectivity : 70 dB
• Audio output power (8 Ω) : 0.2 W (at 1 kHz, 10% distortion)
1-1
SECTION 2. INSIDE VIEWS
• MAIN UNIT
(TOP VIEW)
CHARGING CONTROLLER
(IC601)
SPEAKER JACK
(J251)
M3V LINE SW
(Q225)
2-1
• MAIN UNIT
(BOTTOM VIEW)
5 V REGULATOR
(IC602)
TX POWER AMP
CHARGING CONTROL SW
(Q54)
(Q602)
AF POWER AMP
TX POWER AMP
(IC362)
(Q55)
1ST IF FILTER
(FI151)
IF DEMODULATOR IC
(IC170)
VCO
2ND IF FILTER
(FI170)
NOISE AMP
(IC365)
DISCRIMINATOR
(X170)
PLL IC AF LPF/LIMIT AMP/AF AMP
(IC1) (IC200)
EEPROM
(IC340)
CPU
CPU CLOCK (IC360)
(X360) 3 V REGULATOR
(IC220)
FLASHING LED
(DS247)
2-2
SECTION 3. DISASSEMBLY INSTRUCTION
PCB
SP cable
,
J251
Front panel
Wet sensor
2) Remove 4 screws from the PCB, and then remove
wire the CHASSIS.
4 screws
J602
6 screws
PCB
Chassis
• ANTENNA SWITCHING CIRCUIT The 21.25 MHz reference frequency signal from the PLL IC
The RF signal from the antenna is passed through the LPF (IC1, pin 2) is applied to the IF demodulate IC (IC170, pin 2)
(L81, L82, C83–C86, C89) and antenna SW (D52, D90, as the 2nd LO signal, and then mixed with 21.7 MHz 1st IF
L90, C90, C91), and then applied to the RF AMP (Q90) signal from the 1st AMP (Q151). The resulting signal of 450
through the 2-staged tuned BPF (D92, D93, L92, L93, C95, kHz 2nd IF signal is output from the pin 3 of IC170.
C97–C100, C117).
The 2nd IF signal is filtered by the external ceramic filter
• RF AMPLIFIER (FI170) to extract 450 kHz signal only, and then applied
The filtered RX signal is amplified by the RF AMP (Q90) to the internal quadrature detector to be frequency-
and passed through another 2-staged BPF (D130, D131, demodulated. The demodulated AF signals are output from
L96, L97, L110, L112–L115) to remove unwanted signals. the pin 9.
The filtered signal is applied to the 1st mixer (Q150).
The quadrature detector is a frequency demodulator which
uses a discriminator (X170) as a phase delayer, and
• RF CIRCUITS provides demodulation without any adjustment.
ANTENNA
D52 D90
TX CIRCUITS ANT
SW
LPF SQUELCH CIRCUIT
A portion of AF signal from the IF demodulate IC is adjusted
D131 D130 D 93 D 92 in level by the D/A converter (IC190), and then applied to
Q90
To 1st mixer
BPF BPF
RF
BPF BPF
the noise amplifer (IC170, R174–R176, C179, C180).
AMP
T1CON
Only noise components (approximately 30 kHz signal) are
amplified by the noise amplifier, and then rectified by the
internal noise detector to be converted into DC voltage
corresponding to noise level; the squelch voltage. The
squelch voltage is output from the pin 14 of IC170, and then
applied to the A/D port of the CPU (IC360, pin 33).
1ST IF, 2ND IF AND DEMODULATOR CIRCUITS
• 1ST IF CIRCUITS
The CPU (IC360) compares input voltage and preset
The RX signal is mixed with 1st LO signal at the 1st
squelch level to control audio signals ON/OFF (emit/mute).
mixer (Q150), resulting in the 21.7 MHz 1st IF signal. The
converted 1st IF signal is filtered by the crystal filters (FI150
and F151) to remove unwanted out-of-band signals.
RX AF CIRCUITS
The demodulated AF signal from the IF demodulate IC (IC170,
The filtered 1st IF signal is amplified by the 1st IF AMP
pin 9) is passed through the AF mute SW (IC260D) and LPF
(Q151), and then applied to the IF demodulate IC (IC170,
(IC365). The filtered AF signal is de-emphasized by R286 and
pin 16).
C285 to obtain –6 dB/oct. of frequency response, and then
applied to the D/A converter (IC190). The level-adjusted AF
• 1ST IF CIRCUITS signal is amplified by the AF power amplifier (IC362), and then
1st LO signals
applied to the speaker (CHASSIS: SP1).
from VCO
FI150,FI151
• 2ND IF, DEMODULATOR AND RX AF CIRCUITS
Q151
To IF IC IF 21.7MHz From RF AMP IC1
BPF FI170
AMP 1st IF signal
450KHz
Q150 PLL IC
BPF
21.25 MHz
2ND LO signal
X1 IC170
IC365 IC260D 21.25MHz
X170 RSSI
SQLI
SQLO
Int. SP
J250
VOL
SPO IC362
Ext. SP AF OUT AF DE -
AM P ENPHA
4-1
4-2 TRANSMITTER CIRCUITS
TX AF CIRCUITS TX AMPLIFIERS
AF signal from the microphone (MIC signals) is passed The frequency-modulated signal from the VCO (Q21, Q22,
through the MIC mute SW (IC260A), amplified by MIC AMP D22) is passed through the buffers (Q23 and Q24) and LO
(IC200B), and then applied to the D/A converter (IC190), SW (D50), and then sequentially amplified by the buffer
through another MIC mute SW (IC260C). AMP (Q50) and pre-drive AMP (Q53).
The level-adjusted MIC signal is pre-emphasized by R201 The amplified signal is splitted by the power splitter (L100,
and C385 to obtain +6 dB/oct of frequency response, and L101, R463, C445, C446) and applied to the power AMPs
then passed through the limiter (IC200A) to prevent over (Q54 and Q55). The amplified signals are combined at the
deviation. The amplitude-limited MIC signal is filtered by the power combiner (L107, L108, R465, C457, C458) to obtain
splatter filter (IC200D) to remove 3 kHz and higher signals, the TX output power.
and then applied to the VCO (Q21, Q22, D22) for frequency
modulation. The amplified TX signal is passed through the ANT SW
(D52) and LPF, and then applied to the antenna.
• TX AF AND MODULATION CIRCUITS
Q 21,Q22 Q23 Q24 APC CIRCUIT
D22 To LO switch
BUFF BUFF A portion of TX output signal is rectified by D91 to produce
the DC voltage which corresponds to the TX power level.
Q20
MOD D 20
MUT E D21
The APC AMP (IC50) compares the voltage and TX power
MOD
VCO setting voltage from the D/A converter (IC190). The resulting
voltage from the APC AMP controls the gain of both driver
IC190
AMP (Q53) and power AMPs (Q54 and Q55), to keep the TX
D/A
output power stable.
IC200D
IC200A
Q55
PWR
AMP
IC50
Q357 D91
APC PWR
CTRL DET
PCON
Receive circuits
4-2
4-3 FREQUENCY SYNTHESIZER CIRCUITS
VCO
While transmitting, the oscillatinon frequency of VCO (Q21, PLL
Q22, D22) is determined by the value of D22, L22, C26 and IC1 is a PLL IC which contains the prescaler, programmable
C27, and the frequency modulation is carried out by adding counter, phase comparator and charge pump in its package.
modulation signal to D20.
The 21.25 MHz reference frequency signal is fed from X1.
The generated signal is passed through the buffers (Q23
and Q24), and then applied to the pre-drive AMP (Q53), The loop filter for the VCO is composed by R8, R10, R22,
through the LO SW (D50) and buffer (Q50). C11, C13 and C24.
IC1
Q 21,Q22 D 50,D51
D22 Q23 Q24
PLL IC LOOP
FIL
BUFF BUFF
LO
SW
TX AMPs
PLL control signal
Q25
PLLO
BUFF
X1 BPF
21.25MHz
2ND LO
VCO
IC170 Q150
IC360
Q221
R3V
SW R3V : To the RX circuits
Q222
T3V
SW T3V : To the TX circuits
4-3
4-5 PORT ALLOCATIONS
• CPU (IC360)
PIN LINE PIN LINE
DESCRIPTION I/O DESCRIPTION I/O
No. NAME No. NAME
1 BEEP Beep audio (Squarewave). O MIC mute control.
101 PTTM O
L=MIC mute.
2 PS PLL power save mode control. O
[PTT] input.
Decoded tone signal. (for monitoring 103 PTTIN I
3 TDEC O H=Pushed.
purpose)
TX power control.
4 DASTB Strobe for the D/A converter. O 106 LOW O
H=TX power is set to low.
5 PLSTB Strobe for the PLL IC. O
Transmitting control.
Serial data for the PLL IC and D/A 107 TXMS O
10 SDATA O H=TX mute.
converter.
[16/9] input.
Serial clock to the PLL IC and D/A 108 16/9 I
11 SCK O L=Pushed.
converter.
[CH/WX] input.
12 ESCK Serial clock for the EEPROM. O 109 CH/WX I
L=Pushed.
13 ESDA Serial clock from/to the EEPROM. I/O [Y] input.
110 UP I
25 RES CPU reset. I L=Pushed.
27 TEMPV Temparature sensing voltage. I [Z] input.
111 DOWN I
L=Pushed.
28 BTEMPV Battery temparature sensing voltage. I
[FAV] input.
29 LOINV Lock voltage from the PLL IC. I 112 FAV I
L=Pushed.
30 TDETV TX power sensing voltage. I
[VOL/SQL] input.
31 BATTV Battery voltage. (Divided voltage) I 113 VOL/SQL I
L=Pushed.
32 RSSIV RSSI voltage from the IF demodulate IC. I [SCAN] input.
114 SCAN I
Noise level sensing voltage from the L=Pushed.
33 NOISV I
IF demodulate IC. [H/L] input.
116 H/L I
34 DCV Input voltage detection. I L=Pushed.
36 WDECV* Weather alart tone signal. I PLL unlock signal input. (PLL
117 UNLK malfunction detection) I
38 ATIS** ATIS signal. O
H=PLL unlocked.
51– SEG0-
LCD driver segment terminals. O [ ] input.
72 SEG21 119 PWSW I
H=Pushed.
77 LEDS Backlight control. O
78 CRESET Charging control IC reset. O
79 LCDS LCD contrast control. O • D/A CONVERTER (IC190)
MIC mute SW control. PIN LINE
80 MICMS O DESCRIPTION
L=MIC mute. No. NAME
MIC control. 1, 2 FCON Reference frequency adjustment voltage.
81 ATX O
H=While transmitting. 3, 4 PCON TX output power adjustment voltage.
AF power AMP control. 9, 10 MODC Deviation adjustment.
85 AFVS O
H=While the squelch is opened.
11, 12 MSENS MIC signal level (MIC sensitivity) adjustment.
86 V3VS VCO power supply control. O
13, 14 VOLO AF output power adjustment.
87 M3VS Main power supply control. O
15, 16 SQLO Squelch threshould level adjustment.
TX power control.
88 LOW O 21, 22 T1CON BPF tuning voltage.
H=The TX power is set to Low.
R3V line control.
89 R3VS L=W h i l e r e c e i v i n g . ( R X c i r c u i t s O
activated)
T3V line control.
90 T3VS L=While transmitting. (TX circuits O
activated)
97 PON Main power supply line control. O
RX AF line mute.
98 DETMS O
L=Mute.
Charge status.
99 LEDI-R L=While charging. I
Pulse=Charging error.
Charge status.
100 LEDI-G I
L=When the battery is fully charged.
*: M24 only **: [FRG] and [HOL] only
4-4
SECTION 5. ADJUSTMENT PROCEDURE
5-1 PREPARATION
¤ REQUIRED EQUIPMENTS
EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE
Cloning software CS-M24/M23 ADJ (Revision 1.0 or later) Cables OPC-478UC and OPC-2091
Frequency range : 0.1–300 MHz
Frequency counter Frequency accuracy : ±1 ppm or better
Measuring range : 0.1–6 W Input level : Less than 1 mW
RF power meter
Frequency range : 100–300 MHz
(50 Ω terminated) Frequency range : 0.1–300 MHz
SWR : Less than 1.2 : 1 Standard signal
Output level : –20 dBµ to 90 dBµ
generator (SSG)
(–127 to –17 dBm)
¤ CONNECTION
RF power meter
0.1–6 W/50 Ω OPC-478UC
(USB type)
Frequency
counter To [DC]
OPC-2091
5-1
¤ ADJUSTMENT UTILITY SCREEN
ADJUSTMENT CONDITION
REFERENCE FREQUENCY
TX OUTPUT POWER
RX SENSITIVITY
SQUELCH
5-2
5-3 RECEIVE ADJUSTMENTS
1) Select an adjustment item using [↑]/[↓] on the PC's keyboard.
2) Set or modify the adjustment value as specified using [←]/[→] on the PC's keyboard, then push [ENTER].
TRANSCEIVER’S ADJUSTMENT
ADJUSTMENT OPERATION VALUE
CONDITION ITEM
RX SENSITIVITY 1 NOTE: When "RX SENSITIVITY" is re-adjusted, "SQUELCH" must be re-adjusted too.
• CH. : 16 • Connect an SSG to the antenna connector and Push [ENTER]
• Receiving set it as; on [BPF].
Frequency : 156.800 MHz (Automatic
[BPF]
Level† : +30 dBµ (–77 dBm) adjustment)
Modulation : 1 kHz
Deviation : ±3.0 kHz
SQUELCH 1 NOTE: When "RX SENSITIVITY" must be adjusted before "SQUELCH." And when "RX SENSITIVITY" is
re-adjusted, "SQUELCH" must be re-adjusted too.
• CH. : 16 • Connect an SSG to the antenna connector and Push [ENTER]
• Receiving set it as; on [Noise].
Frequency : 156.800 MHz (Automatic
Level† : –4 dBµ (–111 dBm) [M24] and [AUS] [Noise] adjustment)
–3 dBµ (–110 dBm) [M23] except [AUS]
Modulation : 1 kHz
Deviation : ±3.0 kHz
†
; The output level of the standard signal generator (SSG) is indicated as the SSG’s open circuit.
5-3
SECTION 6. PARTS LIST
M.=Mounted side (T: Mounted on the Top side, B: Mounted on the Bottom side)
S.=Surface mount
6-4
SECTION 7. MECHANICAL PARTS
MP2
EP1
MP51(CH)x2
MP22(CH) MP13(CH)x2
MP48(CH) MP52(CH)
W2(CH)
MP12(CH)
MP14(CH)
To J602(M)
MP33(CH)
J31(CH)
MP35(CH)
MP31(CH)
MAIN UNIT
MP34(CH)
MP32(CH)
MP16(CH) MP39(CH)
MP42(CH)
MP33(CH)x4 MP362(M)
MP50(CH)
MP17(CH)
MP7(CH)
MP363(M) Abbreviations;
MP18(CH) MP360(M) (CH): CHASSIS PARTS
MP15(CH)
MP361(M)
(M): MAIN UNIT
SP1(CH)
MP6(CH) MP1(CH) MP33(CH)x5
EP360(M)
W1(CH)
To J251(M)
MP53(CH)
MP5(CH)
7-2
SECTION 8. BOARD LAYOUTS The combination of this page and next page shows
the top side and bottom side of actual P.C. board.
• MAIN UNIT
(TOP VIEW)
SP−
SP+
J251
V50
2 1 [DC]
J601
V45
C155
MC250 EP11
HV
Q151
R153
C157
R154
V40
C156
D357
R264 R155
C160
C608
C159 R156 GND
D601
C282
C607
Q603
Q364
GND
R608
C617
Q363
R640
R397
R639
Q606 Q353 Q354
V35
IC601
R607
R398
D360
IC260
R648
J251
R641
R609
DS242 DS243
R235
C606
D358
D359
R628
R475
C391
R476
R647
C390
D609
C223
C609
C603
R602
R642
R611
R610
V30
R225
C262
R223
R236
C222
R222 R224
Q225
Q224
R228
R471
D610
C224
Q221 Q222 C225
R226
DS248
MP22
R192
V25
R227
R36
Q366
C620
C44
R194
R652
C192 C57
R65
C465
V20
IC50
Q351
Q357
R66
C56
R401
R386
DS245
DS244
C58 R384
R381
R67
R469
C460 R477
R68
R81
R467
R466
R382
Q365
R383
V15
C461
R70
C64
C77
R69
C60
C59
C380
C466
S329 R73
C621
C66
V10
R74
C78
V5
DS240 DS241
V0
H0 H5 H10 H15 H20 H25 H30 H35 H40 H45 H50 H55 H60 H65 H70 H75 H80 H85 H90 H95 H100 H105 H110 H115
8-1
The combination of this page and next page shows
the top side and bottom side of actual P.C. board.
• MAIN UNIT
(BOTTOM VIEW)
V50
WET SENSOR [PTT]
PWSW
MOD
SP-
SP+
C251
V45
SP−
SP+
CL
J602 J602
R478
CP240
R251
C191
R253 C254
C382
GND
R270
2 1 X170 C467
R258
Q250
R415
C252
R252
R414
C200
C400
R255
C182 C170
FI170 R413
R257
C462
C463
V40
C257
C230
C229
C227
C228
R412 C619
R170
C402
R627
IC220
R256
C618
C611
R261
R260
IC200
C177 R171 C389
R173
R242
Q240
IC170
C464 R202
C622
IC602
R262
R240
R468
C379
R402 C181
R176
C171
R432 C436 C260
V35
R391
C179
R174
C288 R203
R212
Q602 R204
C377
C615
R152
C378
R379
C283
R175
R201
C205
C616 C180 R207
R206
J601
C174 R172 C261
R213
C437 R378 R377 C385
IC362
C154
R376
C610
CP245
C206
C264
R271
C176
R263
C300 C202
D603
R430
C360
C207
Q230
R388
R214
R205 R300
R272
R459
R371
C614
C265
R431
IC365
V30
D356
R273
R458
C12 R372
B7482B
R109 R451 R279 R457
D612
R283
R231 C9
Q609
L98
R373
C111 C121 C440
R105
R107
C266
R278
C96 R286 C438
R113
R230
R91
R94
R93
R374
Q231
C103
L1
C120
MP20
C114 R452 R277 R434
C61
C104 C285 R435 C373
IC360
C119
R110
C231
C102 C263
L96
C110
R450 R276 C8
C404
R433
C375
D130
R103
C95
C99
R95
D131
D92
R97
Q150
IC190
C374
C194
V25
R115
C131
D93
C50
R120
R50
C101
L26
R193
D604
Q90
C113
D51
C98 C117 R121 C386
C116
D50
R122
Q608
R53
R96
R52
C193
L93
EP10
C115
C112
R104
R111
Q25
C41
C613
C38
L92 C42 R650
C452
C451
R54
C62
Q24
R33
C39
C51
C52
D353
C133
C367 R651
R55
C22
L104
R35
L25
Q23
V20
L50
C53
C43
L20
C94
C363
L24
C364
C21
L23
C40
R47
C92
R57
Q50
C365
D90 R2
R34
R32
R31 R30 C401 D350
R20
DS247
R56
C54
R24 C393
C2
R3
R76
C20
Q55
C132
R464
L105
C612
C91
R1 D1 CP360
EP8
L51
L90
L103
R634
R25
C37
R71
D21
R26
C28 C125 R4 C366 Q350
C456
C450
C73
C3
R352
R353
C4
C455
V15
Q21
MP20
C454
C33
R361
C449
C126 C7
Q20
R460
L58
R343
D20
IC341
C90 C35 R351
L101
L108
Q53
C341
R395
R463
C446
C6
R6
R27 R28
EP3 C67
C32
L100
R465
C457
R23
C68
C441
D52 R7
CP80
D355
IC1
C447
Q22
X1
R461
C63
R396
C26 C27
C448
R340
R341
C372
D91
C435
R462
X360
V10
C65 C69
D3
C80
L102
L81
Q362
R5
R75
R380
EP2
C445
C443
C442
C340
D22 C25 C5 C15
IC340
C453
R80 C89
C84
L56
C86
R22
R8
CP1
C72
L57
L80
C24
C371
R10
R11
R12
C85
C83
C82
Q3
V5
C13
C11
C81
C458
CP1
C71
C70
R13
V0
H115 H110 H105 H100 H95 H90 H85 H80 H75 H70 H65 H60 H55 H50 H45 H40 H35 H30 H25 H20 H15 H10 H5 H0
8-2
SECTION 9. BLOCK DIAGRAM
Q608:2SJ347F
CHASSIS Q609:LDTC144TE
D612:L1SS400E
DS247:RT3-239HRH16T
DS248:SML-A12UT
WET FLASH
DET LED MAIN UNIT ANTENNA
J1
Q 21,Q22:KTC3770U
HV D 50,D51: D52:1SV307
HV M3V IC1:MB15E03SLPFV1 Q362:LDTC144EE Q23: Q24: Q50: Q53: Q54:
D22:HVB350BYPTL 2SC4215 2SC4215 HVD144A KTC3770U RD01MUS2 RD07MUS2B D90:HVD144A
PLL IC LOOP
BUFF BUFF
LO
BUFF
PRE
DRIVE
PWR PWR PWR ANT
LPF
FIL SW SPLITTER AMP COMBINER SW
T BATTERY VOLTAGE
SP Q603:
LDTC144EE
MOD
Q25: IC50:LMV321IDCK D 91: Q351:
MODC 2SC4215 Q 357:LDTA144EE RB706F LDTA144E E
FCON
CRESET RESET TDETV
PLLO APC PWR T3V TX TXMS
F
BUFF BPF
CTRL DET MUTE SW
VCO
INPUT DC 6.0V PCON
RSSI V T1CON
MICMS LOIN V
Q353: Q606: 450KHz
AM P
NOISV
HV RSQ035P03TR RSQ035P03TR VCC X170
JTBM450CX70 DETMS NOISV
PWR PWR IC365:
CTRL CTRL LMV358IPW
IC260D: IC365: ETXDO TEMPV
CD4066PWR LMV358IPW PLL DATA BUS
SQLI
SQLO
PCON
PON D609: FCON TDET V BATTV
L1SS400 T1CON
VOLO
IC362: M62364FP VCC VCC
TPA0211DGN
POWER SW
PWSW PTTM
AF Q224:KTC811U
AM P Q225:KTA1664 IC220:
BEEP Q366:LDTC144EE NJU7772F03 ATX PON
IC200C: M3V
LM324IPW REG CPU CPU3V
CLONE CLONE 3V M3VS 3V
SW
AM P
VCC
Q364:2SJ347 F
D360:LRB551 AFVS AF DS246:
REG Q221: IC341: 4.9152MHz TAK-35920
IC200D: IC200A: L2SA1576AS NJU7704F03A
ADJ CK POINT Q 230:RSQ035P03TR LM324IPW LM324IPW R3V CPU X360
CR-911
Q231:KTC811U LPF REG RESET RESET
PSW D356:L1SS400 (SPLATTER) LIMIT PRE R3 R3VS
AMP ENPHA
HV
HV LCD
SP- Q222: IC360:
Q350:LDTC144TE L2SA1576AS UPD78F0338GC
SP+ D350:KDS122 T3V
ERXDO REG EEPROM
CLONE CLONE T3 T3VS
ERXDI
MIC IC340:S-24C64CI-T8T1U3
D356:L1SS400
GND LEDS LED LED
SW
PTT EXTMIC
Q240: DS240,DS241:
LMUN5213DW1 SML-512WW
IC260A: IC200B: IC260C: DS242,DS243,DS244,DS245:
CD4066PWR LM324IPW CD4066PWR LNJ426W83RA
MC250
MIC INMI C AF
AMP
AF
MUTE MUTE
A TIS
KEY
ATX MIC PTTM MICMS
CONT
Q250:LDTC144EE
PTTIN
S250
PTT
9-1
SECTION 10. VOLTAGE DIAGRAM
SCK
DAST
SDATA
SQLO
MODC
PCON
FCON
T1CON
M3V M3V
CPU3V
R193
C191
0.01
C194
0.01
470
R251
MOD
270
IC190
M62364FP DS246
1 VIN1 24 TAK-35920
LNJ426W83RA
LNJ426W83RA
LNJ426W83RA
LNJ426W83RA
VIN8
2 VOUT1 23
SML-512WW
SML-512WW
VOUT8
C251
3 VOUT2 VOUT7 22
10
4 8 4 VIN2 21
DS240
DS241
DS242
DS243
DS244
DS245
VIN7
C438
C200
0.01
V+ V+ 5 VDD 20
0.1
GND
GND GND DAST 6 LD 19
RESET
11 4 7 CLK 18
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
VDAREF
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
COM0
COM1
COM2
8 DI DO 17
R192 9 VIN3 16
IC200 IC365 390 VIN6
LMV358IPW MCON 10 VOUT3 VOUT6 15
2
3
4
5
7
8
9
6
1
20
21
22
23
24
25
LMV324IPW
10
11
12
13
14
15
16
17
18
19
11 VOUT4 VOUT5 14 VOLOUT
12 VIN4 VIN5 13
C192
10
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
R194
100K
C193
0.01
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
COM0
COM1
COM2
R242
R286
C285
10K
0.1
EXB28V821J
R478
R240
R468
MC250
10K
220
220
R270
EM6027P-46C33-G Q240
1K
LMUN5213DW1
C437 C261
0.47 0.1
DET 4 3
MICO
TX:2.98V
MSENS
R252
R263
33K
RX:0.00V 5 2 LEDON:2.98V
0.001
18K
C252
R260
220K
R261
R435
2.99V
56K
12K
6 1
PTTSW
ATX
R434
C382
Q250 C263
82K
R276
LDTC144EE 22K 0.01
1
C260
4.7
R262
C262
0.01
PTTIN
47K
ATX
T3VS
V3VS
AFVS
R3VS
M3VS
MICG
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
MICMS
LEDS
CRESET
LCDS
R433
100K
C404
IC365 R279
C389
2
C360
0.01
1
R277 1.5K
SW-149
IC260
10
1
100K
S250
CD4066BPWR 3
1 14
I/O1
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
VDD
2 13
O/I1 CONT1
3 12 R272
O/I2 CONT4 C265
S23
S22
S21
S20
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
R271
P87/S39
P86/S38
P85/S37
P84/S26
P83/S35
P82/S34
P81/S33
P80/S32
P97/S31
P96/S30
P95/S29
P94/S28
P93/S27
P92/S26
P91/S25
P90/S24
WDECV
4 11 DETIN
BEEP
I/O2 I/O4 24K 120K 100P
5 10 DETO
CONT2 O/I4
R371
470K
6 9 R273
CONT3 O/I3
7 8 22K
VSS I/O3
C254
91 60 SEG9
0.1
MICIN
VSS0 S9
MICG R388 92 59 SEG8 R373
VDD0 S8
MICMS 470K 93 58 SEG7
0.027
P60 S7 1M
R278
C266
0.0056
DETMS 94 57 SEG6
P61 S6
1K
C264
PTTM 95 56 SEG5
P62 S5
R374
390K
96 55 SEG4
P63 S4
PON 97 54 SEG3
P64 S3
C402
R253
3.3K
R258
4.7K
C385
0.01
DETMS 98 53 SEG2
0.1
P65 S2
LEDI-R 99 52 SEG1
C467 P66 S1
R372
1.5M
1.45V LEDI-G 100 51 SEG0
C373
0.47
120P P67 S0
PTTM 101 50
R264 P40 SCOM0
R201
2.2K
TXMS 107 44
P46 VLC1
C374
0.47
C375
0.47
6 2 13 16/9 108 43
R202 R379 P47 VLC0
7 1 14 CH/WX 109 42
100K 82K P50 VLCDC
5 3 12 UP 110 41
P51 CAPL
IC200 DOWN 111 40
P52 CAPH
CP405 IC200 IC200 FAV 112 39
P53 AVREF1
C257
0.01
C386
0.47
VOL/SQL
R256
113 38 ATIS
0.018
0.001
18K
P54 P120/AO0
R214
R257
4.7K
R204
4.7K
R391
C377
820P
C379
C205
C206
SCAN 114 37
15K
47K
47P
P55 AVSS0
CP410 R376 115 36
H/L P56 ANI9
100K 116 35
P57 ANI8
1.43V UNLK 117 34
R402 C464 P70/TO4 P17/ANI7
SWCTRL 118 33
P05/INTP5/BUZ/PCL
39K 0.1 P71/TI4 P16/ANI6
HV PWSW 119 32
P03/INTP3/ADTRG
C401 R413 P72/TO52 P15/ANI5
CMODE 120 31
P33/TO50/TI50
P34/TO51/TI51
4.7 4.7K P73/TI52 P14/ANI4
R206
P20/RXD0/SI3
P21/TXD0/SO3
F
18K
R432 C436
P00/INTP0
P01/INTP1
P02/INTP2
P04/INTP4
P22/ SCK3
2.7K 0.47
P31/TI00
P32/TI01
P25/SCK1
P10/ANI0
P11/ANI1
P12/ANI2
P13/ANI3
R412
P30/TO0
P23/SI1
P24/SO1
CP409
AVREF0
10K
R414
RESET
TX:0.00V
10K
VSS1
VDD1
C202
VPP
XT2
XT1
RX:3.70V
0.1
X2
X1
CP400 9
Q230
8 RSQ035P03TR
2
3
4
5
7
8
9
6
1
20
21
22
23
24
25
26
27
28
29
30
10
11
12
13
14
15
16
17
18
19
10 AFV BEEP WDECV
IC200 DCV
CP401 CP360
LMV324IPW
4
6
RES
TDEC
0.047
0.047
C361
C613
C282
0.0033
R300
6.8K
R415
R430
270K
CP402 PS
47K
C400
R205
8.2K
10
C300
0.1
C283
0.1
CP406
2
3
1
IC362
C372
NOISV
0.1
TPA0211DGN DASTB RSSIV
CP404 8 1 BATTV
VO- IN
R431
7 2
GND
1K
SHUTDOWN Q231
6 3
*C367
0.047
0.047
SE/ BTL VDD
C363
C364
5 4 KTC811U SDATAO
VO+ BYPASS
R634
4
6
SCLK X360
10K
9
CP408
CR-911
R283
100K
J251
0.068
L1SS400 330 0
C288
R361
3
1
3
1
EXB28V102J
2
4
C231
R230
0.047
0.047
0.047
0.047
1
*MP22
R452
2.2K
R450
C370
C371
C366
C393
C365
C612
330K
330
30P
39P
BTEMPV
TEMPV
TDETV
SDATA
PLSTB
LOINV
ATIS
AFVS
DAST
SCK
PSW
CLONE
R340
100K
10K
C340
0.01
R343
KDS122 IC340
10K
1K 2 7 VIN 5 1
CH/WX A1 WP VDD CD
3 6 2
0
UP FAV
A2 SCL VSS
4 5 4 3
0.068
Q350 R351
C435
0.22
S322 LDTC144TE 1K
S328
ERXDI
ERXDI
ETXDO
ETXDO
DOWN
ESCK
ESDA
ESCK
ESDA
VPP
VPP
RES
RES
VOL/SQL
*: Refer to the PARTS LIST for the value and name of component.
10 - 1
TX:2.25V TX:2.62V
• MAIN UNIT (2/2) RX:2.31V RX:0.00V
V3V T3V
MPZ1608S221A
MPZ1608S221A
R7 TX:2.84V
MMZ1005A152ET
R6 1 RX:2.86V
R31
220
R32
150
MP20
2601
47K 470
M3V 2
R53
100
R54
R76
100
10
3
EP3
EP2
4
0.001
0.001
R460
C125
C132
C61
100
0.30-1.3-5TL
0.1
CP80
0.001
0.001
0.001
0.001
EP8
10
0.1U
0.1U
C6
2.62V
C466
C465
L23
L24
C69
47P
C31
C36
C38
C62
0.001
L20
NLV25T
10
10
0.01
470P
R30
68K
C63
C68
47P
C67
C73
0.001
0.001
82 L21 L22 L82
0.1U
0.1U
C32 C40 L57
2.2K
3.3K
L50
L53
L58
R52
R55
C50
C52
NLV25T C6342A 1.5P 15P L56 0.30-1.3-5TL C453 L107 D52 C80 L81 0.30-1.4-6TL
R33
39K
L55
C37 C39 0.30-0.9-3TR 0.001 0.30-1.7-7TL 1SV307 0.001 0.26-1.1-7TR
R20
100
0.75P 12P
C7
Q20 Q54 C74
C26
36P
C72
1
C54 L51 C65 L99 C444 L100 C447 L102 L80 C84
6.8K
R23 LDTC144EE Q23 Q24 RD07MUS2B-T112 0.001 0.30-1.7-7TL 0.001
TX:1.35V
R26
220 15P 82N 47P 56N 0.001 47N 24P 22N 11P
C457
IC1 2SC4215 2SC4215 RX:0.00V
C21
Q21
0.001
10P
9P
C89
R465
MB15E03SLPFV1-G-BND-E1 KTC3770U Q50
100
MA2S077G0
C20
C22
D50 C51 KTC3770U 7P
9P
R463
C446
SCK TX:0.58V
100
HVD144A
12P
CLK FIN 22P L101
R34
270
SDATA 9 8 RX:0.62V
0.001
DAT XFIN R8 R22 ELJRF
R36
120
220P
10 7 Q53
D21
PLSTB L108
C44
C33
0.001
560 4.7K
R80
82K
LE GND
C81
18P
C82
18P
11 6 RD01MUS2 0.30-1.7-7TL
R28
100
C35
PS DO
PS 12 5
0.001
ZC VCC
C442
C443
C445
C448
C456
C458
UNLK 13 4
R75
100
18P
27P
18P
56P
C70
91P
C71
27P
15P
C83
22P
C85
24P
C86
L/F VP D20 D51
8.2K
9P
D3 14
R27
3 MA2S077G0 HVD144A
L1SS400 P OSCO C34
0.22
15 2 MOD
R10
560
C13
0.001
0.001
R OSCI 1.5P
0.1U
1.2K
16 Q22
L25
1
R50
R56
R57
R71
100
C41
C53
C55
27P
R25
1K
68
KTC3770U Q362
330
100K
R5
LDTC144EE C43
R35
39K
22P EP10
D22 R69
0.001
R73 MPZ1608S221A
C126
0.30-1.3-5TL
0.22
C11
X1 HVB350BYPTL-E R462 10K
0.001
10K
0.001
0.001
C24
R3 R4
10
C3 C42
100K
R74
56K
CR-766 0
C25
R24
3
C27
27P
C28
C30
0.001
0.001
10K 47K 220P 5P
150K
Q25
R461
C451
470P
FCON
C452
R70
220
C64
C77
0.1
C66
C78
0.1
0.001
47P
2SC4215
C441
L104
R380
F L106
10K
2
1
L1050.30-1.3-5TL
HVC376B-E
Q55 0.30-0.9-3TR
C57
0.01
RD07MUS2B-T112
10P
15P
RB706F-40
C2
C4
C5
D1
T3V
MODC
24P ELJRF
R384 C58 R477 R68
0.1 10K 100
D91
2.2K
TXMS 4.5W:0.79V
C450
PCON
1.0W:0.17V
56P
Q351 R67 R81
R464
C454
C455
100
91P
27P
LDTA144EE 120K 100K
R386
TDETV
10K
R466
10K R382
NOISV
5 2.7K
1
C133 IC365
4
0.001 R65
5 3
R467
0.001
0.001
150K IC50
56K
R401
100K
0.01
C461
C460
7 Q365
R11
470
R66
68K
R47
C15
C56
0.1
LMV321IDCK
0.001
2
470P
3.9K 6 LDTA144EE
C59
C60
0.001
R383
C380
R457
12K
R458 R381
10K
R12
R459
4.7K
C440
0.1
10K 4.7K 10K
LOW
Q357
Q3 LDTC144EE
2SK1069-4-TL-E L1 C12 R173 R170 R120
LOINV NLV25T 0.001 1.5K 390 2.2K
4.5W:2.21V R469
R3V 1.0W:1.72V 10K
JTBM450CX70
ELOW
R171
2.7K
0.0056
C182
*C622
*C618
0.001
4.7
CP1
R109
C177
C170
C160
R122
150K
TX:0.00V R3V
0.1
10
R155
2.2K
RX:1.20V
X170
R113
2nd Lo
TX:0.00V
R13
10K
R121
10
22K
IC170 RX:2.57V
C8
2P
C9
2P
LQH1N
RX:2.71V RX:1.85V
0.022
0.001
0.022
OSCIN MIXIN 82N 0.01
LQN21A
R110
1.8K
C157
C121
C120
C119
FI170 2
L98
15
47P
OSCOUT GND
R156
R154
100K
R103
120K
C104
0.01
LTM450FW C462 3
L96
14
470
10K
R95
0.1 MIXOUT NOISEREC C159 C116 C113 C109
C171
4 13
47P
Q150
KDV214E
7 10
KDV214E
0.1 C101
KDV214E
0.001
KDV214E
FILOUT QUAD 3SK293
C154
1.94V 8 9 FI151 FI150 6P
R153 R152
R1
D131
D130
FL-399A FL-368
D92
Q90
D93
C181 0.001 1K 1K
TEMPV Q151 3SK294
0.1 R172
470 KTC3880S TX:0.00V
DB2S31400
HVD144A
C179
DET RX:1.08V
R176
C155
270P
LQN21A
LQN21A
LQN21A
D90
1K
100K
D353
3P
C91
10P
C90
0.001
0.001
R2
R115
390K
R111
100K
R107
220K
R105
220K
R104
100K
270K
220K
220K
9P
C176
C174
C131
C115
C114
C112
2.5P
C110
C103
C102
0.01
C100
L97
L93
L92
R97
220
R96
R94
R91
11P
47P
33P
47P
C99
27P
C97
C95
22P
3P
3P
2P
R174
330K
R3V
0.001
0.001
C111
C96
T1CON
RSSIV T3V
CH A RG E : 6. 0 0 V C HA R G E: 4 . 96 V 4 . 76 V
Q353
RSQ035P03TR CP300
*C620
*C621
RT3-234HRH16T-BNS
RX:2.74V RX:0.00V 2.86V LRB551V-30
R650
EZJZ0V80010
5
4
4
1M
J601 D601 D603 R602 Q608
Q363
LRB551V-30 RSQ035P03TR LRB551V-30 1 2SJ347 CP240
R652
R648
R397
270K
220
I O
D357
Q602 R628
0
G
DS247
KTA1664 1 D609
SML-A12UT
Q225
4
3
1
1
C611
KTA1664
L1SS400
C610
0.33
4.7
10 10K CP245
DS248
Q606
R651
10K
D612
C609 RSQ035P03TR
C224
C603
0.01
R610
10K
0.001
R471
V3V
10
IC220
C230
*C617
0.001
R227 IC602
R398
0.1
R627
2.2K
R607
R639
C229
10K
Q222
0
470
10K
0.001
0.001
10K NJM2835DL1-05
3
R647
C391
C390
L2SA1576AS L2SA1576AS 1 5 NJW4100V
10K
VIN VOUT Q609
2 1 20
GND P_CHG Q-CHG
C615
LDTC144TE
5
4
6
3 4 2 19
150
CTRL NC Q364 NFB CS1
3 18
LRB551V-30
5 16 D358
10K
KTC811U NC VREF
6 15 LDAN222
D359
F-CHG V+
R641
2.2K
R235
330K
7 14 Q354
MMZ1005Y102CT
R223 R225 D360
2
3
1
S329
LDTC144EE 180K C2 CHG-SW 2
0.001
EP11
LM3Z3V0
C228
C227
0.047
R476
R642
R609
R611
4.7K
R640
R236
150K
C222
0.01
C223
0.01
C607
0.01
C608
C606
C616
C225
0.47
D604
10K
470
10K
0.1
47P
1
CPU3V
1K
Q603
CRESET
LEDI-G
LEDI-R
BTEMPV
CLONE
CMODE
BATTV
LDTC144EE
R3VS
T3VS
M3VS
PWSW
VIN
DCV
PON
PSW
HV
PON: 2.99V
POFF:0.00V
*: Refer to the PARTS LIST for the value and name of component.
10 - 2
1-1-32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Phone : +81 (06) 6793 5302
Fax : +81 (06) 6793 0013
URL : http://www.icom.co.jp/world/index.html
Ctra. Rubi, No. 88 Bajos A 08174, Sant Cugat del Valles, Barcelona, Spain
Glenwood Centre #150-6165
Phone : +34 (93) 590 26 70 Fax : +34 (93) 589 04 46
Highway 17 Delta, B.C., V4K 5B8, Canada
URL : http://www.icomspain.com
Phone : +1 (604) 952-4266 Fax : +1 (604) 952-0090
E-mail : [email protected]
URL : http://www.icomcanada.com
E-mail : [email protected]
Blacksole House, The Boulevard, Altira Business Park, Herne Bay, CT6 6GZ, UK
Unit 1 / 103 Garden Road, Clayton VIC 3168 Australia Phone : +44 (01227) 741741 Fax : +44 (01227) 741742
Phone : +61 (03) 9549-7500 Fax : +61 (03) 9549-7505 URL : http://www.icomuk.co.uk
URL : http://www.icom.net.au E-mail : [email protected]
E-mail : [email protected]
Zac de la Plaine
146A Harris Road, East Tamaki, 1 Rue Brindejonc des Moulinais BP 5804
Auckland, New Zealand 31505 Toulouse Cedex, France
Phone : +64 (09) 274 4062 Fax : +64 (09) 274 4708 Phone : +33 (5) 61 36 03 03 Fax : +33 (5) 61 36 03 00
URL : http://www.icom.co.nz URL : http://www.icom-france.com
E-mail : [email protected] E-mail : [email protected]