3RD SEM./AERO./DIP.MECH/MECH(MAIN/PROD/SAND/ IND.

INT/AUTO)/
MECH. ENGG 2020(W)NEW
Th-1- Production Technology

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1 & 2
Figures in the right-hand margin indicates marks

10
1. Answer All questions 2 x 10
a. What is blanking operation?
b. Why cores are needed in casting?

07
c. Explain Sintering process.
d. Why dies are used in press work?
e. Name any two materials suitable for Oxy-acetylene Welding Process.
03
f. Jigs & Fixtures increases the production cycle time (True/False). Justify
your answer.
g. Define Extrusion process.
04

h. Classify the different types of Rolling Process.

i. What are the benefits of Production Technology in Engineering?
j. What do we understand by economics of casting?
07

2. Answer Any Six Questions 6x5

01

a. The machining allowance for cast iron for size up to 12 inch is 0.12 inch
and from 12 inch to 20 inch is 0.20 inch. Redraw the dimension of the part
shown in the figure with dimensions including machining allowance.

1
 b. Discuss about the oxidizing and reducing zones of a cupola furnace.
c. Compare Jigs with Fixtures
d. Explain Resistance welding process.
e. Discuss about the various types of punches.
f. Compare hot rolling with cold rolling.

10
g List the different advantages of powder metallurgy.

3 Explain 3-2-1 point location of a rectangular jig. 10

07
4 Write short notes on: 10
a Compound Dies
b Direct Extrusion
03
c Blending
d Undercut
04

5 Discuss about various types of destructive and non-destructive types of 10

tests carried out to detect welding defects.
6 Explain GMAW process with neat sketch. 10
7 Discuss about any five types of casting defects, its causes and remedies. 10
07
01

2
 3RD SEM/MECH/AERO/AUTO/DIP. MECH /MECH(MAIN)/ MECH(PROD)
/MECH(SAND)/MECH(IND.INT) /MECH.ENGG AUTO/ 2020 (W) NEW

Th-2 Strength of Material

Full Marks:80 TIME:3 Hour

Answer any five question including QNO 1 & 2 are compulsory.
Figures in the right hand margin indicate marks.
N01. Answer all questions. (2X10)

(a) Define temperature stress

(b) What is the difference between stress and strain?

8
(c) Define point of contra-flexure.
(d) Define cantilever beam with example.

70
(e) What is resilience?
(f) What do you mean by hoop stress and longitudinal stress?
(g) What do you mean by column?
(h) Define torsion
60
(i) What do you mean by section modulus?
(j) Define principal stress and its uses.

NO2. Answer any six questions. (5X6)

40

(a) A rod 150cm long and of diameter 2.0cm is subjected to an axial pull of
20KN. If the modulus of elasticity of the material of the rod is
2X105N/mm2. Determine (I) the stress (II) the strain, and (III) the
0

elongation of the rod.

07

(b) Show diagrammatically different types of beams and loads.

(c) What are the assumptions taken while deriving bending equations under
theory of simple bending?
(d) Derive expression for hoop stress and longitudinal stress in case of thin
01

cylindrical shell.
(e) Find the maximum shear stress induced in a solid circular shaft of
diameter 15cm when the shaft transmits 150kw power at 180 r.p.m
(f) Derive the formula section modulus for rectangular section and circular
section.
(g) Derive relationship between modulus of elasticity and modulus of
rigidity.
(h) A point in a strained material is subjected to two mutually
perpendicular tensile stresses of 200Mpa and 100Mpa. Determine the
intensities of normal, shear and resultant stresses on a plane inclined at
30° with the axis of minor tensile stress.
NO3. Prove the relation

M/I= /y=E/R

Where M= bending moment

I= moment of inertia

= bending stress in a fibre, at a distance y from the neutral axis

E= young’s modulus and

8
R= radius of curvature (10)

NO4. A simply supported beam of length 6m carries point load of 3KN and 6KN

70
at distances of 2m and 4m from the left end. Draw the shear force and bending
moment diagram for the beam. (10)

NO5. A reinforced short concrete column 250mmX250mm in secton is

60
reinforced with 8 steel bars. The total area of steel bars is 2500mm2. The
column carries a load of 390KN. If the modulus of elasticity for steel is 15times
that of concrete, find the stresses in concrete and steel. (10)
40

NO6. Define buckling load. State formula for buckling load in column with
various end condition. (10)
0

NO7. A brass bar having cross-sectional area of 1000mm2 is subjected to axial

07

forces shown in the figure. Find the total elongation of the bar. Modulus of
elasticity of brass is 100GN/m2. (10)
01
 3RD SEM./ AE & IE/ ELECTRICAL &MECH/ ELECTRICAL & ETC/ EE(I&C) /
EE[PT]/ ELECTRONICS & COMM/ ELECTRICAL /E&TC / 2022(W) 5 3
Th-1 ENGINEERING MATHEMATICS-III
1 1 27
Full Marks: 80
2 4
0 including Q No.1& 2
Answer any five Questions
Time- 3 Hrs

Figures in the 0
0 2 3 right hand margin indicates marks

1. Answer All questions-2 2 × 10

2
a. Find the modulus
1
0and amplitude of the complex number √ .
3
19the1rank of a matrix. Find the rank
b. Define
5 3 of the matrix ( ).

c. Find the complementary function2

1 7
of ( ) .

0 1
4 equation for the function ( ).
d. Construct a partial differential

3 2
0 of a function and find ( ).
e. Define Laplace transform

2 2
0 function and find the period of the function ( ). 3
f. Define periodic

0 -
1 in the Fourier series of ( ) in the interval [– ]. 75
1 3 2
g. Find
1 2
1 9 h. 4 1
Define the Shift operator and write the relation between shift operator
0
( ) and forward
difference operator ( ).
0 2
3 as unity.
i. Calculate
0 2
by taking the interval difference
State Lagrange’s interpolation formula to-2
j.
2 0 1 interpolate a function.

3 3
2.
191
Answer Any Six Questions
1 .2 7 5 5×6
a If , Show that
0 4 1
3 0 2
2 0 2
1 -
b. Determine the rank of the matrix [ ] by using elementary row transformation
7 5 3
method.32
0 3 1 2
5 1
1911( 127 )
c. Solve .
0 2 0 4
4
0 the Laplace transform of the function ( ) { 02
d. 2Find
3
2 3 0 - 2
2 0 e. Find the Fourier series of the function ( ) 2{ 0 1
0 1 - 1 3 .

32 1 9
1 f. Find a real root of the equation ,
by using bisection method in three steps.

1
 5 3
g.
1 1 27
Find the cubic polynomial which takes the following values:
: 0 4
201 2 3
( ) : 1 30 2 1 10
Hence, evaluate ( ). 20
2
0 1 -
a. For what 1 3 2
3
1 9 values of and the equations
,3
7

7 5 ,
2solution and (iii) an infinite number of solutions.
4 1 1
have (i) no solution, (ii) a unique

2 0
b. If are0the three cube roots of unity,
3
2 0( 2 3
-
Prove that
0 1 ( ) ( ) ( ).
) ( )
5 3
4
2
a. Solve
3 1 2 7 7
1
1 b. Find the inverse Laplace transform of ( ) ( )2041
9
2 3 0 3
5 a. Find ( )
- 2 0 5

2 0 1
by using 3
b. Evaluate ∫
9 1 Simpson’s 1/3 rule,
7 5 3
1
and compare the result with its actual value. 2
1
5

6 Obtain the Fourier series for

0 4 1
( ) { 3 0 2 10

2 0 2 .

1 - 7 5 3
3 2 0
Hence Prove that
3 1 2
7 a. Develop
9 1 a 7 5
recurrence
2 formula for finding the value of √ , using
4 1
Newton-Raphson 7
1 1and1 hence, compute this value correct to three decimal places.
method
0 2 0
2 0 4 2 3
3b.0 Find the square roots of - 2 0
2 0 2 √ .
0 1 3

1 - 1 3 2
2 0 1 9
13

2
 2 5
3RD SEM./ ELE & MECH/ ELE. AND ETC./ELECTRICAL /
EE(I&C) /ELECTICAL[PT]. / 2022(W)
1 23
1
Th-2 Circuit 2 6
0and Network Theory
2 3 0
Full Marks: 80
Answer - 2 0
any five Questions including Q No.1& 2
Time- 3 Hrs

2 1
0 in the right hand margin indicates marks
Figures
3
1. 191All questions
Answer 2 5 2 x 10

a. What is magnetizing force? 1 Also

3
2 state its SI unit.
6 1
b. What do you mean2by0mesh analysis of AC networks?.
c. State the 0 2 30 theorem.
Thevenin’s

1 - 2(i) Q-factor (ii) Selectivity in series circuit 2 5

3 0
d. Define
2Find the total inductance of three series connected coupled coils23
9 1 e.
61 1 as shown below
1 2 0
with L =1H; L =2H; L = 5H,
1 2 3

2 3 0
M =0.5H;M =1H;M =1H
12 23 13

- 2 0
2 0 1
3 5
191 1 2 3 2
0 6 1
f. Give an example of (i) 2 3 02Element (ii) Non linear Element
Passive

- 2 0 5
g. What do you mean
0 1 by phase sequence in polyphase system?
2 3 2
h. What is3
1 23 2
impedance2 5 and impedance triangle?
1 1
1 9 1 2 0 6
i. Define
6 1 filter. Give an example
0 are short-circuit admittance parameters? 02 30
j. 2What
2 3 0 - 2
2 02. Answer Any Six Questions 2 0 1
0 1 - 1 3 6x5
32 1 9 materials in details with a neat diagram.
a. Explain the hysteresis loop of magnetic
1
b. How the 3-phase power is measured by two wattmeter method?
c. Describe briefly about π section of a circuit network.
 d. Write a short note on hybrid (h) parameters 2 5
1 1 23
e. Find the open circuit parameters of the following two port network.
20 6
2 30
1 - 20
1 3 20
1 9 5
3 2
0 6 112
f.
30 2
Explain the sinusoidal response of series R-C circuit.

g 0 2
Find the current in 5Ω resistor using Norton’s theorem across a-b terminals of the
2
0 1 - shown below. 2 5
32network
1 23
19 1 61
0 2 0
2 3
01 -20
32 5
191 1 23 2
0 61
3 0 2
20 2
1 - 3 2 5
3
3 2 0 5 1 2
Derive the relation between phase and line quantities in star connection. 10
9 1 2 3 2 on (i) Source Transformation technique (ii) Dot Convention.
61
4 Write
1 11 short notes
0 2 0 10
5
2 0 6
Explain
2 3
the transient response of series R-L-C circuit having DC Excitation. 10
6 30 Write short notes on (i) Constant K low pass filter
- 2 0
(ii) Star to delta 10
2 0 2 0 1
-
1 7
transformation
3 2
1 circuits in details with neat diagrams. 10
2 0 1 9
Explain the series and parallel magnetic
13
 3RD SEM/ ELECTRICAL/ 2022(W)

7
Th-3 Element of Mechanical Engineering
0
Full Marks: 80 1 136 Time- 3 Hrs
Answer any five Questions
2 0 7 including Q No.1& 2
Figures in the 3
2 0 hand margin indicates marks
right
Answer All questions20
1.
0 -
1 by Indicated Horse Power of an engine?
a. What do you understand
2 x 10

1 3 2
b. Define super-heated steam.
c. State1 9 7
the use of accumulator in a hydraulic circuit.
st
d. State 1 Law of Thermodynamics.
3 6 0
1
e. What is the difference between
7 1 Density and Weight Density?
f. Define condenser. 0
3 0 2
h. What is2the0 2function of a pump?
g. How an IC Engine works?

0 1 -the Continuity Equation. 0 7

i. State
j.32Name the different types of Boilers. 1 3 6
1
12.9 Answer Any Six Questions 7 1
0 2 0
a. A pipe 400 mm diameter is branched into 0 2 3
two pipes of diameter 250 mm
6x5

1
and 110 mm respectively. If the average 2
- velocity in 400 mm diameter pipe is
3
2.1 m/sec and average velocity 2 0
in 250 mm diameter pipe is 2 m/sec then find
the velocity in 110 mm9 1 pipe and total
diameter
6 0 7
discharge.
1
b. Explain Specific Weight, Dynamic Viscosity3and Surface Tension of a fluid.
1 and limitations of a condenser.
c. Define surface condenser? List the7 1
0with Dry Bulb Temperature.
merits
d. Compare Wet Bulb Temperature 0 2
3 and Pneumatic devices.
e. Differentiate Hydraulic2
- 0 devices
2 State its use in a hydraulic/pneumatic circuit. 7
0 1
f. What is an intensifier?
g Derive the2relationship of specific heat of gases at constant volume3and6 0
1 3 6 0 7 1 1
constant
1 9 1
pressure.
3 2 0 7
3
0 7
State 1
Bernoullii’s Theorem. Derive the equation. 3 0 10
4 02 2
Explain about 2-stroke Diesel Engine with neat sketch. 0 2 10
52
0 3 Define Pressure. Discuss briefly about 1 -
-2 3 2 0 different pressure measuring 10

2 1
0 6
instruments.
1
9 Accessories.
1 3 7
1
Describe about Boiler Mountings and
A cylinder contains 1.1 kg of steam at 1 MPa. If the volume of steam is 0.09 10
10

m3, determine the dryness fraction of the steam, enthalpy and internal
energy of the steam per kg.

1
 3RD SEM. /ELECTRICAL/ ELECTRICAL & MECHANICAL / 2022(W)
Th-4 Electrical Engineering Material
2 7
Full Marks: 80
1 11
Answer any five Questions including Q No.1& 2
1
Time- 3 Hrs

20 8
Figures in the right hand margin indicates marks
1. Answer All questions
2 30 2 x 10
a.
b.
1 - 20
Mention the factors which affect the value of resistivity of a material.
Of what material is high voltage overhead lines for power transmission made?

c.
1 20
Give reasons.
3
Name the conducting material which is generally used in plug points, socket
1 9 7
outlets, switches and lamp holders. State 2 properties of this material should
1 2
possess for such applications.
d.
8
and the best insulator.
0 111
Mention what number of electrons in the valence ring makes the best conductor

e.
30 2
State the use of semiconductor in industrial applications.
f.
g.
2 0 2
State the factors which affect the dielectric loss of an insulating material.
State the difference between a dielectric material and an insulating material as

2 0 1-
regards their functions.
1 2 7
1
h.
3
i. Explain magnetostriction and eddy current loss. 1 1 1
Name the special type of steel used for cores of power transformers. Give reasons.

19 j. What are bimetals? Where are these used? 0 8

30 2
2
-20
2. Answer Any Six Questions 6x5
a. What is resistivity of conductor materials? A resistance wire of length 1 meter and
01
diameter 0.08 mm has a resistance of 95.5 ohms. Calculate the resistivity of the
wire material. 32 7
b.
c. 191 1 2
Explain with the help of energy diagram n-type and p-type semiconductors.
1 1
Name the different classes of varnishes available. Describe what are epoxy resin
81
varnishes and silicone resin varnishes.
0
d. Explain the following:
(i) 3 0 2
Permittivity (ii) Dielectric strength (iii) Dielectric constant (iv)

20 2
Breakdown voltage (v) Loss angle
e.
1 - 2 7
What are ferrites? What are their advantages over other magnetic materials?
1
f.
2 0
Describe briefly the Hall effect and Hall effect generator.
3 7 1 1
2 1
1911111
g. What is superconductivity? Explain the applications of superconducting materials.
0 8
2 Also Mention
3. 0 8
What insulating material would you select for the
2 3 0
following? 10
3 02reasons for the selection:
2 0
0 2 1
(a) Flexible wire (b) High Voltage cable (c) -
Low voltage cable
0machines
-2 3
(d) Fuse Holder (e) Commutator in D.C 2
1 4. Explain the process of polarisation9of1a dielectric material.
2 0 1 magnetic material with suitable diagram.
10

13 5.
6.
Explain the hysteresis loop for different
Write short notes on (a) Soldering material (b) Silica gel
10
10
7. Discuss the physical, electrical and mechanical properties of copper and its use as 10
an engineering material. Where it can be substituted by aluminium and with what
limitations?

1
 3RD SEM. / COMMON / 2022(W)
5 8
Full Marks: 80
Th-5
1 0 42
Environmental studies
Time- 3 Hours

20 9
Answer any five Questions including Q No.1& 2

2 3 0
Figures in the right hand margin indicates marks

1. Answer All questions-2

0 2 x 10

2 0 1
a. Define natural resources.

9
b. Write down
3
1 two examples of non-renewable resources.
1 5 8
c. Define soil erosion.
0 4 2
d. Define producers in eco system.
e. What is bio diversity? 09
1
3 0 2by poaching of wild life?
f.
2
What do you mean
g. What is2 0
0 1 -is endangered species.
the unit of sound intensity?
5 8
2
h. What
4 2
1i.3 Define greenhouse effect. 1 0
19 j. What are the various objectives of family welfare programme. 2 0 9
2 3 0
- 2 0
2. Answer Any Six Questions
2 1
0of mining?
6x5
a. What are the environmental effects
3
1 wild life conflict.258
9man
b. Give a brief description of
1 0 4
c. What are the effects of acid rain.

0 9 1
d. Define rainwater harvesting? State the
e. Describe about Bio gas plant. 3 0 2 objective of rain water harvesting?

f. Write down the role2 of0

2
What are the 0 1 - of modern agriculture?
an individual protecting environment.
2 5 8
g
3 2 effects
5 8 1 0 4
1 9 1 42 0 9
3
1 0 warming, write down the causes and effect of global02warming.
Define Global
9 10
0 sources of solid waste and solid waste management.23
4
5 3 02Explain
2 0 10

06 2 Describe aquatic ecosystem.

1 - 10
2 Write down the effect, prevention and control2of0noise pollution.
0 1 - 1 3 10

32 7 Write short notes on

1 9 10
1 a. Pyramid of energy
b. Green house effect

1
 3RD-SEM./ AERO/ AIRCRAFT MAINT./ AUTO/ DME/ MECH./ MECH(MAINT.)/
2 0
MECH(PROD.) / MECH(SAND.) / MECH(IND.INT.) / 2022(W)
8
1 2
Th-1 Production Technology
1
Full Marks: 80
2 0 4 Time- 3 Hrs
0
Answer any five Questions including Q No.1& 2
Figures in the3right hand margin indicates marks
2
- 2 0
1.
2 0
Answer All questions1 2 x 10

1
a. Define Impact
9 3 extrusion process.
1 Rolling process and classify2its0various types.
b. Define
8
c. Write different types of flames2used in Oxy-acetylene welding process.
4 11 type of pattern in foundry shop.
d. What is pattern? State0different

3
e. State the function 0 2
of flux in welding.
f. Define2 0 2 and its remedies.
0 1 - porosity
2 0
g. 2What is the function of chill and chaplet?
3 1 2 8
1
19 h.i. Define Powder Metallurgy process. 4 1
Define piercing and trimming. 0 2 0
j. What do understand by permeability? 02
3
1 - 2
3 2 0
2. Answer Any Six Questions
9 1 2 0
8 and remedies.
6x5
a. State five numbers of1welding defects, its 2
4 1 1 causes
b. Explain sintering process.
0 0
2 allowances.
0 2 3
c. Explain different type of pattern
d. Differentiate between
1 - 2 TIG and MIG welding process.
2 0
2 0
e. Explain different types of moulding sands with its compositions.
0 1 2 8
3
91 1Compound
f. Explain 2
8 die and Progressive die. 4 1
1
g What 1
2 2 0
0 4 is Centrifugal casting? Explain with neat sketch.
2 3 0
3 02 2 0
32
0 Describe the construction and working principle
0 1 -
of Cupola furnace with a neat 10
1 -2 sketch.
3 2
2 0 4 Explain 3-2-1 location of 9
rectangular
1 1jig. 10
13 5 What is Resistance welding process? Explain Spot welding and Seam welding
with a neat sketch.
10

6 Explain different type of Casting defects and its remedies. 10

7 Explain the process of Power Metallurgy. 10

1
 3RD SEM./AERO/AIRCRAFT MAINT./AUTO/DME/ MECH./ MECH(MAINT.)/
3
MECH(PROD.)/ MECH(SAND.)/ MECH (IND.INT.)/ 2022(W) 3
1 23
Th-2 Strength of Material
1
20 6
Full Marks: 80
3 0
2five Questions including Q No.1& 2
Time- 3 Hrs
Answer any
2 0
Figures-in the right hand margin indicates marks
2 0 1
1.
9
Answer All1 3questions 2 x 10
1 Poisson’s ratio.
a. Define 3 3
b. What is meant by Shear force 2
1 3
diagram and Bending moment diagram?
6 1
c. Define the point of contra-flexure.
d. Define column. 20
e. What is meant 2 3 0
by Temperature stress?
f. What-do 2 0you mean by Section modulus? 3
0 1
2What is the function of shaft? Write down the formula for power 3 3
1
g. Define
3 Principal Stress and Principal Plane.
1 1 2
1 9 h.
0 6 transmitted by
a shaft.
3 0 2
i. Define cantilever beam with example.
j. What is meant by thin cylinder shell? State 2 0 2its application.
0 1 -
Answer Any Six Questions 32
2.
a. A hollow cylinder 1
1
2m9long has an outside 3 3
3diameter of 50mm and inside
6x5

1
diameter of 30mm. If the cylinder is carrying
2
1 a load of 25kN, find the stress in
0
the cylinder. Also find the deformation
2 6 of the cylinder, if the modulus of
elasticity for the cylinder 3
2 0 is 100GPa.
material
b. The stresses at point
- 2 0of a machine component are 150MPa and 50MPa both3
0 1
tensile. Find the
3
intensities of normal, shear and resultant stresses on a plane
2 3
inclined3 at2an angle
3 0
1
9 1 3 3 of 55 with the axis of major tensile stress.
6 1
1 112
c. Show diagrammatically different types of beams and loads.
0 2 0
0
d. What
2 6 are the various assumptions taken while deriving2bending 3 equations under

3 0 theory of simple bending?

- 2 0
2 0 2 e. Derive a formula for the longitudinal stress0in1a thin cylindrical shell subjected to
1 - an internal pressure.
1 3 2
32 0 f. Write down the assumption taken 1 9for finding out the torsion formula.
1 g A solid circular shaft of 100mm diameter is transmitting 120kW at 150 rpm. Find
the intensity of shear stress in the shaft.

1
 3 Prove 3 3 10
E= 3k(1-2/m)
1 1 23
Where E= Young’s modulus
20 6
K= Bulk modulus
2 30
1/m= Poisson’s ratio
4
1 -
Prove the relation 20 10
m/I=
1 3 20
=E/R

1 9
where m= Bending moment
3
3
I= Moment of inertia
3
112
= Bending stress in a fibre at a distance y from the neutral axis

2 0 6
E= young’s modulus

5 30
R= Radius of curvature
2
A cantilever beam AB, 2m long carries a uniformly distributed load of 1.5kN/m 10
0
1- 2 3
over a length of 1.6m from the free end. Draw the shear force diagram and
3
32 0bending moment diagram for the beam.
2 3
1 1
61 thick plates. Find the
169 A cylindrical shell of 1.3m diameter is made up of2018mm 10
0 if the boiler is subjected to
circumferential and longitudinal stress in the3plates,
2
2 0 of the joints as 70%.
an internal pressure of 2.4MPa. Take efficiency
-
0 1
2 and 150mm deep
A rectangular beam 60mm3wide
7
9 1 3 3 is simply supported over a
3 point load of 12KN. Find the
10
1 is subjected 1to2central
span of 6m. If the beam
maximum bending stress induced in the
0 6 1 beam section.

3 0 2
2 0 2
1 - 3 3 3
3 2 0 3 1 2
3 1
1911123 0 2 0 6
2 0 6 2 3
3 0 - 2 0
2 0 2 0 1
1 - 1 3 2
2 0 1 9
13

2
 3RD SEM. /AERO/AIRCRAFT MAINT. ENGG/ AUTO/DME/ MECHANICAL./
MECH(MAINT.)/ MECH(PROD.) / MECH(SAND.) / MECH(IND.INT.) /2022(W)

5 4 0
Th3 Engineering 3 Material
Full Marks: 80
7 1 1 Time- 3 Hrs
0 including Q No.1& 2
2hand
Answer any five Questions
0
Figures in the3right margin indicates marks

2 0 2
1. 0
Answer All questions1 - 2 x 10
2
a. Classify the3engineering material.
b. Give1two 91examples of each of ferrous0and non-ferrous materials.
c. Define crystal and ideal crystal. 3 5 4
d. What is an alloy?
7 1 1
e. Name the various 2
0 0
heat treatment processes.
f. What is meant3by thermosetting polymers?
2 0 2
0 1 -is point defect?
g. Write the purpose of heat treatment process.
4 0
h. What
2
i.3 What is elastomer? 1 3 5
1
19 j. What is dislocation? 71
0 2 0
2. Answer Any Six Questions 0 2 3 6x5
a. Write down the difference between 1 2
-Edge dislocation and Screw dislocation.
3
b. Differentiate between thermosetting
0
2 and thermoplastic polymers.
1
9 of ceramics and3write
c. Give a brief classification
5 0
4down their uses.
1
d. State the composition and properties of1Duralmin and Y-alloy.
0 7
e. Differentiate between slip and twinning.
1
0
f. Briefly explain the cooling curves
3 2 for a material with a neat diagram.
g What is effect of various
2 0 2 alloying elements such as Cr, Mn, Ni,V and Mo?
1 - 5 4 0
3 Explain the
3 2 0 0
iron carbon
1 3
equilibrium diagram with salient micro constituents of 10
9
iron 1 steel
and
3 5 4
with a neat diagram. 7 1
4 1 1
Describe 0
1in detail the composition, properties and uses0of2tin based bearing 10
2 0 7
material. 2 3
5 30 Explain in brief the following heat treatment processes:- 2 0 10
2 0 2 0 1
1 - (i) Annealing
1 3 2
2 0 (ii) Hardening
1 9
13 6
7
Explain various mechanical properties of engineering materials.
Describe in detail the composition, properties and use of a copper base spring 10
10

material.

1
 3rdSEM./ AERO/AIRCRAFT MAINT.ENGG/AUTO/DIP MECH ENG./MECH./
MECH(MAINT.)/ MECH(PROD.) / MECH(SAND.) / MECH(IND.INT.) / 2022(W)

4 7
Full Marks: 80
1 11
Th-4 Thermal Engineering-I
1 Time- 3 Hrs

20 8
Answer any five Questions including Q No.1& 2

2 3 0
Figures in the right hand margin indicates marks

Answer All questions 20

1.
0 1
a. What do you understand
- by an ideal gas?
2 x 10

1 3 2
b. Define thermodynamics.
c. Classify9
1 IC engines according to the4type 7 of fuel used.
1
d. What is the significance of octane 1 number in IC engine fuels?
1 and extensive properties.
8 1
e. Differentiate between intensive
0
f. Define the calorific2value of fuel.
g. Define a Heat3
2 0
Engine.

- 0 by compression ratio in an IC engine?

h. What is2meant
7
0 1
i. State
2 the Zeroth Law of thermodynamics. 1 4
1 j.3 Define thermal efficiency.
1 1 1
19 2 0 8
2. Answer Any Six Questions
2 3 0 6x5
a. Explain Carnot Cycle.
- 2 0
b. In a heat engine, the temperature1 0 0
of the source and sink are 650 C and 60 C
3
respectively. The heat supplied
0
2 is 4.5 MJ/min. Find the power developed by
9 1 1 4 7
the engine.
1
c. Differentiate between Octane number 1 1
and Cetane number.
0
d. Discuss about the limitations of First8 1
Law of Thermodynamics.
e. Explain the working of a four
3 0 2 engine.
stroke
f. Prove C - C = R.
p v 0 2
2 process.
1 -
g Explain the quasi-static
1 4 7
3 2 0 7 1 1
3 9
Explain
4
1 the1diesel
1 cycle with the help of p-V and T-S diagram and 8 1derive an 10
1 1 1 for the ideal efficiency of a diesel cycle. 02
expression
0
4 2 0
An
8
engine uses 6 kg of fuel per hour of calorific value 2 3 kJ/kg. If I.P. of 10
41000
3 0
0 the engine is 21 kW and mechanical efficiency -is282%. Calculate, i) indicated
2 0 2 thermal efficiency, ii) brake specific fuel2 0 1 and iii) Brake thermal
consumption
0 1 - 1 3
32
efficiency.
9
1 function & Path function. Differentiate 10
1 5 Discuss in the detail about Point
between them.
6 Compare a SI engine with a CI engine. 10
7 Show the equivalence of two statements of 2nd Law of thermodynamics. 10

1
 3RD SEM. / COMMON / 2022(W)
5 8
Full Marks: 80
Th-5
1 0 42
Environmental studies
Time- 3 Hours

20 9
Answer any five Questions including Q No.1& 2

2 3 0
Figures in the right hand margin indicates marks

1. Answer All questions-2

0 2 x 10

2 0 1
a. Define natural resources.

9
b. Write down
3
1 two examples of non-renewable resources.
1 5 8
c. Define soil erosion.
0 4 2
d. Define producers in eco system.
e. What is bio diversity? 09
1
3 0 2by poaching of wild life?
f.
2
What do you mean
g. What is2 0
0 1 -is endangered species.
the unit of sound intensity?
5 8
2
h. What
4 2
1i.3 Define greenhouse effect. 1 0
19 j. What are the various objectives of family welfare programme. 2 0 9
2 3 0
- 2 0
2. Answer Any Six Questions
2 1
0of mining?
6x5
a. What are the environmental effects
3
1 wild life conflict.258
9man
b. Give a brief description of
1 0 4
c. What are the effects of acid rain.

0 9 1
d. Define rainwater harvesting? State the
e. Describe about Bio gas plant. 3 0 2 objective of rain water harvesting?

f. Write down the role2 of0

2
What are the 0 1 - of modern agriculture?
an individual protecting environment.
2 5 8
g
3 2 effects
5 8 1 0 4
1 9 1 42 0 9
3
1 0 warming, write down the causes and effect of global02warming.
Define Global
9 10
0 sources of solid waste and solid waste management.23
4
5 3 02Explain
2 0 10

06 2 Describe aquatic ecosystem.

1 - 10
2 Write down the effect, prevention and control2of0noise pollution.
0 1 - 1 3 10

32 7 Write short notes on

1 9 10
1 a. Pyramid of energy
b. Green house effect

1
 III-SEM./ELECTRICAL/ ETE/MECHANICAL /AUTO/AE & IE/CSE/IT
/EEE/MECH(IND INTG)/ ELECTRICAL(INST &CTRL)/ 2021(W)
BST-301 ENGINEERING MATHEMATICS -III

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

47
1. Answer All questions 2 x 10

a. State Rouche’s Theorem.

b. Solve ( )

12
c. Frame a partial differential equation for the function
( ) ( )
d. What is Gamma function? Find (-3.5)
02
e. Find ( )
f. Define even and odd functions with examples.
g. Write Newton Raphson formula to find √ .
03

h. Evaluate ( )
i. State Newton Cotes Quadrature Formula.
j. Define Rank of a matrix.
07

2. Answer Any Six Questions 5X6

01

a. Find the root of the equation correct to three places

of decimal using Bisection Method.
b. Find the Laplace Transform of
( ) {
c. State the Convergence condition of Fourier Series.
Find ( )
d. Evaluate ∫ using Trapezoidal Rule taking h= 0.5
e. Find f(2.8) using Newton’s Backward Interpolation Formula
x 0 1 2 3
F(x) 1 2 11 34
1
 f. Solve ( )
g
Find the rank of the matrix ( ) by Row reduced Echelon

form.

3 i) Find the Fourier Series of ( ) (– ) 6

47
ii)
Solve ( )
4
4 i) Check the consistency and solve by Matrix method 5

12
2x+y+z=5
x+ y+z=4
x-y+2z=1
ii) Evaluate ∫ using Simpson’s rule and taking h =1 5
02
5 i) Solve the following partial differential equation 5
( ) ( ) ( )

ii) Find ( ) 5
03

6 i) Solve by Transform Method 6

with
07

ii) 4
Solve ( )
7 i) Using Interpolation estimate the output of a factory in 1986 from 5
the following data
year 1974 1978 1982 1990
01

Output in 1000 tones 25 60 80 170

ii) Find the Inverse Laplace Transform of ( ) 5
( )

2
 III-SEM./ Electrical Engg./EEE/2021(W) OLD
EET301 Circuit and Network Theory
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10

a. What are open-circuit impedance parameters?

b. Give an example of (i) Passive Element (ii) Bilateral Element
c. A current of 15 A divides between two branches in parallel

43
resistance of 8 ohm & 16 ohm respectively. Calculate the current in
each branch.
d. Draw impedance triangle of RL and RC series circuit.
e. Write down the analogous between electrical and magnetic circuit.

12
f. Define band pass filter and low pass filter.
g. What do you mean by self and mutual inductance.
h. Write down the relationship between line current and phase current
04
in both star and delta connection.
i. What is the true power consumed in a 30V series RLC circuit if Z= 20
ohm and R= 10 ohm?
j. A series RC circuit has |VR| = 12 V and |VC| = 5V. Calculate the
03

magnitude of supply voltage.

2. Answer Any Six Questions 5X6
a. A 230 V, 50 Hz ac supply is applied to a coil of 0.06 H inductance and
07

2.5 Ω resistance connected in series with a 6.8 µF capacitor.

Calculate (i) Impedance (ii) Current (iii) Phase angle between current
and voltage (iv) power factor
b. Use nodal analysis method, find current through 5Ω resistor in the
01

below circuit.

c. Derive the bandwidth of RLC series resonance circuit.

d. Write short notes on hysteresis loop.

1
 e. Find Rth and Vth in the below circuit using Thevenin theorem.

f. Explain dot conversion rules for coupled circuits.

g Derive the expression for the current in the below circuit when the
switch, S is closed at t=0.

43
3

12
State Maximum Power Transfer theorem. Derive the condition of 10
04
maximum power transfer.
4 Explain the concept of Super-mesh and Super-node with one 10
suitable example for each.
03

5 Obtain the Y-parameter of below circuit. 10

07
01

6 A 3-phase balanced, star connected load of (2+j4) ohm is connected 10

to a 3-phase balanced delta connected source with a phase voltage
of 220V. Determine line voltage, phase voltage across the load, line
current and phase current in the load, assume RYB phase sequence.
Also calculate the power drawn by the load.
7 An impedance ZL= (10+j10)ohm is connected in parallel with another 10
impedance of resistance 8.5ohm and a variable capacitance
connected in series. Find the capacitance such that circuit is in
resonance at 5KHz.

2
 3rd Sem./ELECTRICAL/2021(W) OLD
EET302 Electrical Engineering Material
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. What is breakdown voltage?
b. What is skin effect?
c. What is thermocouple material?

46
d. What do you mean by covalent bond?
e. What is the effect of porosity?
f. What do you mean by dielectric loss?
g. Write down any two chemical properties of an insulating material.

12
h. Why conducting materials like copper and aluminium are not used
for making the element for electrical heaters?
i. What are bimetals?
j.
08
What is super conductivity?

2. Answer Any Six Questions 5X6

a. Write in brief about PVC and rubber.
03

b. Classify various types of dielectrics and explain it.

c. Write in brief about photovoltaic cell.
d. State four factors which decide the selection of insulating material
07

for given purpose.

e. Write short notes on Hall effect.
f. Write short notes on Varnishes.
g Explain briefly about fuse material.
01

3 Explain the hysteresis loop for ferromagnetic material with suitable 10

diagram.
4 Explain with the help of energy diagram n-type and p-type 10
semiconductor.
5 Explain the effect of temperature on resistivity. 10
6 Write notes on hard magnetic materials and their applications. 10
7 Explain briefly about magnetostriction and polarisation. 10

1
 3rd Sem./Electrical [PT]/2021(W)
EET302 ELECTRICAL ENGINEERING MATERIAL
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. State any two applications of copper and Aluminium.
b. Define resistivity and conductivity.
c. Write two electrical properties of insulating materials.
d. What is extrinsic semiconductors?

40
e. Define permittivity.
f. What is magneto-striction?
g. State two applications of superconducting materials.
h. Write the difference between bundled and stranded conductors.

12
i. Define polarization.
j. Define eddy current loss.
2. Answer Any Six Questions 6x5
a. Explain about P-type and N-type materials.
07
b. Why carbon material is used as brushes in electrical machines? Write
down other applications of carbon in the field of electrical
engineering.
c. Write short notes on Hall effect generators.
03

d. What is aging of insulating materials? What are the commonly used

insulating gases?
e. With the help of energy band concept differentiate between
semiconductors, conductors and insulators.
07

f. Give a comparison between soft magnetic materials and hard

magnetic materials.
g Explain briefly about electric conductivity of dielectrics and their
breakdown.
01

3 (a) State and explain about hysteresis curve with a neat diagram. 10
(b) Define diamagnetism, paramagnetism and ferromagnetism
4 Classify insulating materials. Write down properties and applications. 10
5 (a) Briefly explain about the properties of dielectrics. 10
(b) Write down five low resistivity materials and five high
resistivity materials.
6 Write notes on fuse materials and soldering materials. 10
7 Write short notes on 10
(a) Thermistors
(b) bimetals

1
 III-SEM./ELECTRICAL/EEE/ 2021(W) OLD
ETT-321 ANALOG ELECTRONICS AND OP-AMP
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. What is knee voltage?
b. What is a clipping circuit?

41
c. What is a filter? Why we need a filter in a circuit?
d. What is ripple and ripple factor?
e. What is avalanche breakdown?

12
f. Define DC load line.
g. What is the need of biasing?
h. Write down the difference between oscillator and amplifier?
i.
03
Draw the circuit diagram of 741 OP-AMP IC.
j. What do you mean by stability factor in transistor?
2. Answer Any Six Questions 5X6
a. Explain the construction and working principle of a PN junction diode in
03

forward and reverse bias condition.

b. With a neat circuit diagram full-wave centre tap rectifier? State its
advantages.
c. Explain the working principle of a Tunnel diode. Explain its characteristics
and use.
07

d. State the relation between α,β,γ.

e. Define Oscillator and explain working of basic Oscillator with simple block
diagram.
f. With a neat circuit diagram, explain the voltage divider biasing used in a
01

transistor amplifier.
g Derive the expression for overall gain of a negative feedback amplifier.

3 Explain how a Zener diode act as a voltage regulator. 10

4 Explain the principle of operation of a Class-B push pull amplifier, with neat 10
circuit diagram.
5 Describe the principle of operation of inverting and non-inverting types of 10
OP-AMP.
6 Write down the working principle of PNP and NPN transistors. 10
7 What is feedback amplifier? Explain the general theory of feedback 10
amplifier.

1
 3rd Sem./Electrical Engineering/ 2021(W)OLD
MET321 Elements of Mechanical Engg.
Full Marks: 80 Time- 3 Hrs
Answer any FIVE Questions including Q No. 1 & 2
Figures in the right-hand margin indicates marks
1. Answer ALL questions 2 x 10
a. What is continuity equation?
b. State Zeroth Law of Thermodynamics.

40
c. Define Mean effective pressure.
d. What is the difference between Pascal and Bar?
e. What do you mean by Heat? State its unit.
f.

12
What is a perfect gas?
g. Give two examples of reaction turbine.
h. What is the necessity of safety valve in boiler?
i. What is diagram factor?
07
j. Define mechanical efficiency of a steam engine.
2. Answer Any SIX Questions 6x5
a. Derive CP - CV = R
03

b. The diameter of a pipe at the sections 1-1 and 2-2 are 250 mm and 300 mm
respectively. If the velocity of water flowing through the pipe at section 1-1 is 4
m/sec. Find discharge through the pipe and velocity of water at section 2-2.
c. Describe properties of fluid.
07

d. Differentiate between two stroke engine and four stroke engine.

e. What is a boiler? Classify it.
f. Derive an expression to determine hypothetical mean effective pressure of a
steam engine without clearance.
01

g Compare surface condenser with Jet condenser.

3 State and Prove Bernouli’s Theorem. 10
4 Find the dimension of a single cylinder double acting steam engine on the basis 10
of the following data. I.P=70 kW. Admission Pressure = 7 bar, Back Pressure of
steam = 1.5 bar, Stroke Length = 1.6 times the cylinder bore, Engine Speed =
120 rpm, Cut-off = 1/4 of the stroke. Neglect Clearance.
5 With a neat sketch explain construction and working of Cochran Boiler. 10
6 Calculate the enthalpy of 1.2 kg of steam at a pressure of 8.5 bar and dryness 10
fraction of 0.7. How much heat would be required to raise 6 kg of this team
from water at 25 ⁰C.
7 State different types of condenser and explain its functions. 10

1
 III-SEM./ELECTRICAL/ETE/AE&IE/EME/ ELECTRICAL[PT]
/EEE/ELECTRICAL(INST & CTRL)/ECE/2021(W)
TH-I ENGINEERING MATHEMATICS -III

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

47
1. Answer All questions 2 x 10

a. What are homogeneous equations? State the condition to get

non-trivial solutions for homogeneous equations.

12
b. Find Particular Integral of ( ) .
c. Frame a differential equation for the function ( ).
d. Write the Existence Theorem of Laplace Transform.
02
e. Find { }.
f. Define Periodic function. Give one example of periodic function with
its period.
03

g. Write Newton Raphson Formula to find a root of equation

( )
h. Evaluate ( ).
i. State Trapezoidal Rule. Why this is called Trapezoidal Rule?
07

j. Express in the form of .

2. Answer Any Six Questions 5x6

01

a. Find the root of the equation correct to 3-places

of decimal by Newton Raphson Method.
b. Find the Laplace Transform of ( ) ( )
c. State Dirichlet’s condition for a function to be expanded in Fourier
Series. Find ( )
In
d. Evaluate ∫ using Trapezoidal Rule with 5 subintervals.
e. Find the Inverse Laplace Transform of
( )
( )( )
1
 f. Find ( ) when x=32 from the following data using Newton Forward
Interpolation Formula
x 30 35 40 45 50
f(x) 15.9 14.9 14.1 13.3 12.5
g Solve the following differential equation
( )

47
3 i) Express ( ) ( ) as a Fourier Series in the interval ( ) 7
Hence deduce the value of the series
ii) Find √ 3

12
4 i) Solve the following partial differential equation 6
( ) ( ) ( )

ii) Evaluate using Simpson’s Rule correct up to 3-places of 4

∫
02
decimal taking h=1.
5 i) Solve the differential equation 5
( )
03

ii) Find the Laplace Transform of ( ) 5

6 i) Find k if the following equations are consistent 5
X+2y-3z=-2
07

3x-y-2z=1
2x+3y-5z=k
ii) Find f(x) when x=15
x 3 7 11 19
5
01

F(x) 42 43 47 60
7 i) Solve the following differential equation 5
( )

ii) If is the cube root of unity, show that 5

( ) ( )

2
 III-SEM./ELECTRICAL/ EME/ELECTRICAL[PT] /EEE /
ELECTRICAL(INST & CTRL) 2021(W)

TH-II Circuit & Network Theory

Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10

40
a. State Ohm’s law.

b. What do you mean by active element. Give two examples.

12
c. Define permeability and reluctance.

d. State KCL & KVL.

e. Give the statement of Thevenin’s theorem.

03
f. State the necessary mathematical formulation for conversion from star to delta
and vice versa.
g. Define power factor and power triangle.
03

h. Define Q-factor and selectivity in series circuit.

i. Define coefficient of coupling.

07

j. Write two property of series resonance.

2. Answer Any Six Questions 5X6

a. (a) Find the power loss in 1Ω resistor of the figure as shown below.
01

b. (a) Find the total inductance of the series connected coupled coils as shown
below.

1
 M12=0.5H,M23=1H,M31=1 H,L1=2H,L2=1 H,L3=2 H

c. Explain briefly about B-H curve.

d. State the condition of resonance in series R,L,C circuit. Derive the expression of

40
resonant frequency for series R,L,C circuit.

e. State and derive the condition for maximum power transfer in a circuit and
write the expression for maximum power.

12
f. Define filter. Classify pass band, stop band filters with neat diagram.

g Briefly explain about the Z,Y,ABCD and h parameters.

03
3 By using superposition theorem find the current through 20 Ω resistor of the 10
circuit as shown in the figure below.
03

4 Draw the characteristics curve between charging current and time during 10
07

charging current and time during charging and discharging condition of a series
RL circuit.
5 Design a HPF (both T and ∏ network) having a cut off frequency of 2 kHz with a 10
load resistance of 300 Ω.
6 Obtain Z-parameters of the below circuit. 10
01

7 A resistance of 10 Ω, an inductor of inductance of 20 H and a capacitor of 10

capacitance 100 micro farad are connected to a single phase 230 V AC source.
Find (i) current, (ii) power factor, (iii) active power consumption corresponding
to supply frequencies of 50 Hz and 100 Hz respectively.

2
 3rd Sem./Electrical Engineering/ 2021(W)

Th-3 Element of Mechanical Engineering.

Full Marks: 80 Time- 3 Hrs

Answer any FIVE Questions including Q No. 1 & 2
Figures in the right-hand margin indicates marks

42
1. Answer ALL questions 2 x 10
a. What is continuity equation?
b. State Zeroth Law of Thermodynamics.

12
c. Define Mean effective pressure.
d. What is the difference between Pascal and Bar?
e. What do you mean by Heat? State its unit.
04
f. What is a perfect gas?
g. Give two examples of reaction turbine.
03

h. What is the necessity of safety valve in boiler?

i. What is diagram factor?
j. Define mechanical efficiency of a steam engine.
07

2. Answer Any SIX Questions 5X6

a. Derive CP - CV = R
01

b. The diameter of a pipe at the sections 1-1 and 2-2 are 250 mm and
300 mm respectively. If the velocity of water flowing through the
pipe at section 1-1 is 4 m/sec. Find discharge through the pipe and
velocity of water at section 2-2.
c. Describe properties of fluid.
d. Differentiate between two stroke engine and four stroke engine.
e. What is a boiler? Classify it.
f. Derive an expression to determine hypothetical mean effective
pressure of a steam engine without clearance.

1
 g Compare surface condenser with Jet condenser.

3 State and Prove Bernouli’s Theorem. 10

4 Find the dimension of a single cylinder double acting steam engine 10
on the basis of the following data. I.P=70 kW. Admission Pressure =
7 bar, Back Pressure of steam = 1.5 bar, Stroke Length = 1.6 times
the cylinder bore, Engine Speed = 120 rpm, Cut-off = 1/4 of the

42
stroke. Neglect Clearance.
5 With a neat sketch explain construction and working of Cochran 10
Boiler.
6 Calculate the enthalpy of 1.2 kg of steam at a pressure of 8.5 bar 10

12
and dryness fraction of 0.7. How much heat would be required to
raise 6 kg of this team from water at 25 ⁰C.
7 State different types of condenser and explain its functions. 10
04
03
07
01

2
 3rd Sem./ ELECTRICAL/ EME/2021(W)
Th4 Electrical Engineering Materials
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. What do you mean by resistivity and state its SI unit.
b. Define dielectric constant. What is the dielectric constant of air?
c. What is N-type semiconductor? Give an example.

40
d. Which properties should a fuse material possess?
e. What are the factors affecting dielectric strength of insulating
material?
f. Name the materials used in making (i) element of a filament lamp (ii)

12
resistors for loading rheostats.
g. What is magnetostriction in magnetic materials?
h. What is photovoltaic cell?
07
i. What do you mean by thermocouple? Give an example of
thermocouple.
j. State an application of (i) Teflon (ii) PVC insulating material.
2. Answer Any Six Questions 5X6
03

a. Differentiate between soft and hard magnetic materials.

b. Describe about the electron energy and energy band theory briefly.
c. Write a short note on soldering materials.
07

d. Explain the domain theory of ferromagnetic material briefly.

e. What are the factors affecting insulation resistance?
f. Describe the applications of superconductor materials.
g Explain the mechanical properties affecting the selection of insulator
01

in brief.

3 Explain the low resistivity materials and their applications in details. 10

4 Describe about fuse and fuse materials. Draw also a cross section 10
view of cartridge fuse.
5 Write a short note on(i)Hall Effect generators(ii) Solar power 10
6 Explain the electrical conductivity and the breakdown of (i) Gaseous 10
dielectrics(ii) Liquid dielectrics
7 Describe about natural and synthetic rubber and their applications. 10
1
 3rd Sem. Common 2021(W)
Th-5 Environmental Studies
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

46
a. Define acid rain.
b. What is ecological succession?
c. What do you mean by soil erosion?
d. Define genetics and species.

12
e. Mention any two causes of marine pollution.
f. Define environment.
g. What is mortality?
h.
08
What do you mean by sustainable development?
i. What leads to conflicts over water?
j. Define water pollution.
03

2. Answer Any Six Questions 6x5

a. Define and explain food chain with at least one example.
b. Explain the changes caused by modern agriculture.
c. Explain Biodiversity at National level.
07

d. Give a brief note on ozone layer depletion along with its consequences.
e. Discuss in brief ‘Human Rights’.
f. Discuss the needs of public awareness towards environment.
01

g Explain cyclone disaster management.

3 Explain the effects of mine extraction on environment and tribal people. 10

4 Explain different threats to biodiversity. 10
5 Describe forest ecosystem. 10
6 Write down the causes, effects and controlling measures of soil pollution. 10
7 a Urban problems related to energy. 5
b Family welfare program. 5

1
 III-SEM./ELECTRICAL/ ETE/MECHANICAL /AUTO/AE & IE/CSE/IT
/EEE/MECH(IND INTG)/ ELECTRICAL(INST &CTRL)/ 2021(W)
BST-301 ENGINEERING MATHEMATICS -III

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

47
1. Answer All questions 2 x 10

a. State Rouche’s Theorem.

b. Solve ( )

12
c. Frame a partial differential equation for the function
( ) ( )
d. What is Gamma function? Find (-3.5)
02
e. Find ( )
f. Define even and odd functions with examples.
g. Write Newton Raphson formula to find √ .
03

h. Evaluate ( )
i. State Newton Cotes Quadrature Formula.
j. Define Rank of a matrix.
07

2. Answer Any Six Questions 5X6

01

a. Find the root of the equation correct to three places

of decimal using Bisection Method.
b. Find the Laplace Transform of
( ) {
c. State the Convergence condition of Fourier Series.
Find ( )
d. Evaluate ∫ using Trapezoidal Rule taking h= 0.5
e. Find f(2.8) using Newton’s Backward Interpolation Formula
x 0 1 2 3
F(x) 1 2 11 34
1
 f. Solve ( )
g
Find the rank of the matrix ( ) by Row reduced Echelon

form.

3 i) Find the Fourier Series of ( ) (– ) 6

47
ii)
Solve ( )
4
4 i) Check the consistency and solve by Matrix method 5

12
2x+y+z=5
x+ y+z=4
x-y+2z=1
ii) Evaluate ∫ using Simpson’s rule and taking h =1 5
02
5 i) Solve the following partial differential equation 5
( ) ( ) ( )

ii) Find ( ) 5
03

6 i) Solve by Transform Method 6

with
07

ii) 4
Solve ( )
7 i) Using Interpolation estimate the output of a factory in 1986 from 5
the following data
year 1974 1978 1982 1990
01

Output in 1000 tones 25 60 80 170

ii) Find the Inverse Laplace Transform of ( ) 5
( )

2
 III-SEM./ MECH/MECH(IND INTG)/AUTO/ 2021(W)OLD
MET-301/MET321 STRENGTH OF MATERIAL
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. Define poisson’s ratio.

41
b. Define shear force and bending moment diagram.
c. What is cantilever beam with example?
d. Define torsion.

12
e. What is the difference between stress and strain?
f. What is temperature stress? Write its formula.
g. What do you mean by column?
h. Define principal stress.
03
i. State Hooke’s law.
j. Define section modulus.
03

2. Answer Any Six Questions 5X6

a. Show diagrammatically different types of beams and loads.
b. What are assumptions taken while deriving bending equations under theory of
07

simple bending?
c. Derive expressions for hoop stress and longitudinal stress in case of thin
cylindrical shell.
d. A simply supported beam of length 6m carries point load of 3KN and 6KN at
distances of 2m and 4m from the left end. Draw the shear force and bending
01

moment diagram for the beam.

e. The principal stresses at a point across two perpendicular planes are 75MN/m2
(tensile) and 35MN/m2 (tensile). Find the normal tangential stresses and the
resultant stress and its obliquity on a place at 200 with the major principal plane.
f. A solid shaft of 150mm diameter is used to transmit torque. Find the maximum
torque transmitted by the shaft if the maximum shear stress induced to the shaft is
45N/mm2
g What are the assumptions of torsion equation?
h. A rectangular beam 200mm deep and 300mm wide is simply supported over a
span of 8m. what uniformly distributed load per metre the beam may carry, if the
bending stress is not to exceed 120N/mm2

1
3 Define buckling load, state formula for buckling load in column with various end 10
conditions with diagram.

4 Prove the relation M/I= /y=E/R 10

Where M=Bending moment
= Bending stress in a fibre at distance y from the neutral axis
I= Moment of inertia
E= young’s modulus

41
And R= radius of curvature

5 A cantilever of length 2.0m carries a uniformly distributed load of 2kN/m length 10

over the whole length and a point load of 3KN at the free end. Draw the S.F and
B.M diagrams for the cantilever.

12
6 At a point in a strained material the principal stresses are 100N/mm2(tensile) and 10
60N/mm2(compressive). Determine the normal stress, shear stress and resultant
stress on a plane inclined at 500 to the axis of major principal stress. Also
03
determine the maximum shear stress at the point.

7 Derive the relation between three elastic constant. 10

03
07
01

2
 III-SEM./ Mechanical Engg./MECHANICAL(IND INTG)/AUTO/ 2021(W)OLD
MET-322/MET-302 Engineering material
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Classify the engineering material.
b. What is point defect?

43
c. What is line defect ?
d. State the application of ceramic.
e. What is heat treatment?
f. What is slip?

12
g. Name any two non-ferrous metal and two ferrous metal.
h. What is elastomers?
i. What is hardenability of steel?
j. Write down uses of stainless steel.
04
2. Answer Any Six Questions 5X6
a. Describe mechanical properties of materials.
b. State various causes of edge dislocation and screw dislocation.
03

c. State the composition and properties of Duralimin and Y-alloy.

d. Explain the different types of line defects,
e. What are classification, composition properties and uses of copper base spring
material.
07

f. Explain fiber reinforced composites with their application.

g Differentiate between thermosetting and thermoplastic polymers.
h. Explain surface hardening heat treatment process.
3 Describe the composition, properties and uses of copper base bearing material and tin 10
01

base bearing material.

4 Explain iron-carbon equilibrium diagrams and show the micro-constituents of iron and 10
steel in different phase.
5 Explain the following heat treatment process 10
(i) Normalizing
(ii) Annealing
6 What is elastomers, write down the properties and application of thermosetting and 10
thermoplastic polymers.
7 What is the purpose of painting? Explain methods of industrial painting. 10

1
 3th SEM./MECH/MECH(IND INTG)/ 2021(W) OLD
MET-303 Thermal engineering-1
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Define properties and its different type.
b. What do you understand by the concept of continuum?

40
c. Define pressure. State its unit.
d. What is radiation type heat transfer?
e. What is meant by renewable energy sources?
f. Write the first law of thermodynamics for change of states.

12
g. Write the efficiency of heat engine.
h. Define entropy.
i. Define sensible heat and latent heat.
j. Sate the Guy Lussac’s equation?
07
2. Answer Any Six Questions 6x5
a. Explain the different equilibriums in thermodynamics.
b. Explain the quasistatic process.
03

Derive the COP of heat pump and refrigerator by applying the 2nd
c.
law of thermodynamics.
d. Apply the steady flow energy equation in turbine and compressor.
If the specific volume of wet steam at 15bar is 0.125 m3/kg, then find
07

e.
the dryness fraction of steam.
f. Derive the expression for the work-done for Polytropic process?
g Explain the limitations of first law of thermodynamics.
01

3 Give the detailed expression for steady flow processes by applying

10
the first law.

In a gas turbine, gas enters at the rate of 10kg/s with a velocity of

50m/s and enthalpy of 920kJ/kg and leaves the turbine with a
velocity of 170m/s and enthalpy of 400kJ/kg. Loss of heat to the
4 10
surrounding is 25kJ/kg. Assume for gas R=0.285kJ/kgK,
cp=1.005kJ/kgK and inlet conditions to be 100kPa and 27°C.
Determine the power output of the turbine and diameter of inlet
pipe.
1
 A refrigeration plant operates as a reversed Carnot heat engine
cycle. Store is to be maintained at a temperature of -5°C.
Atmospheric temperature is 25°C. If the heat transfer from the store
5 10
to the cycle is at the rate of 5kW, then calculate the power required
to drive the plant.

40
A mass of 8kg gas expands according to the law pv1.2=constant. Initial
pressure is 1000kPa and initial volume is 1m3. Final pressure is 5KPa.
6 If the specific internal energy of the gas decreases by 40kJ/kg, then 10
find the total value of heat transfer.

12
Write the short notes on the following:
(a)Dalton’s law of partial pressure
7 (b)Ideal and Real gas 10
07
(c)Dryness fraction
(d)Open and Closed system
03
07
01

2
 III-SEM/MECHANICAL/AUTO/AERO/DIP IN MECH/MECH(PROD)
/MECH(MAINT)/MECH(IND INTG)/MECH(SWICH)/ 2021(W)
TH-1 Production Technology

Full Marks: 80 Time- 3 Hrs

Answer any FIVE Questions including Q No.1&2
Figures in the right-hand margin indicates marks

1. Answer ALL questions 2 x 10

47
a. What is metal forming?
b. Classify the welding process.
c. Name any four types of welding defects.
What do you mean by reusability of moulding sand?

12
d.
e. What is meant by machining allowance in pattern making?
f. State the steps in core preparation.
g. Define sintering process.
What is trimming operation in press work?
h.
02
i. Why jigs are needed in production process?
j. Define casting process.

2. Answer Any SIX Questions 5X6

03

a. Compare Plate fixture with Angle-plate fixture.

b. Describe briefly about progressive dies with a neat sketch.
c. Explain Compacting process in press work.
d. What do you mean by a hanging core? Explain briefly.
07

e. Differentiate between TIG & MIG welding process.

f. Discuss about different types of rolling process.
g State the need of using flux in welding.
01

3 Describe Electric Arc Welding Process with neat sketch. 10

4 Discuss the working principle of Cupola Furnace. 10
Explain about different non-destructive tests carried out to detect
5 10
casting defects.
6 Explain briefly the difference between Jigs with Fixtures. 10
Discuss briefly about the different secondary processes for
7 10
producing components using powder metallurgy techniques.

1
 III-SEM./MECH/AUTO/AERO/DIP IN MECH
/MECH(PROD/MECH(MAINT) /MECH(IND INTG) /
MECH(SWITCH)/ 2021(W)
TH-II Strength of Materials
Full Marks: 80 Time- 3 Hrs
Answer any FIVE Questions including Q No.1&2
Figures in the right-hand margin indicates marks
1. Answer ALL questions 2 x 10
a. Define Stress.

40
b. State the Hook’s Law.
c. Write down the expression for Strain Energy.
d. Define Hoop stress.

12
e. What do you understand by Principal Stresses?
f. Write the significance of Mohr’s Circle.
g. State different types of beams.
03
h. What is pure bending?
i. Explain Crippling Load.
j.
03

Define shaft.

2. Answer Any SIXQuestions 5X6

07

a. State the assumptions made in theory of bending.

Find the reactions of simply supported beam when a point load of
1000 kg and a uniform distributed load of 200 kg/m is acting on it
as shown in figure below:
01

b.

c. Explain Temperature stress and derive its expression.

d. Derive the torsion equation for a solid circular shaft.
A circular bar is subject an axial pull of 120 kN. If the maximum
e. intensity of shear stress on any oblique plane is not to exceed 55
MN/m2, find the diameter of the bar.
1
 f. Find the generalized equation for Shear Force & Bending Moment
of a simply supported beam with Uniformly Distributed Load.
A steel rod 22mm in diameter and 1.5meters long is subjected to an
g axial pull of 35 kN. Find i) The intensity of stress, ii) The strain &
Elongation. Take E=2x105 N/mm2

3 Derive the expression for Hoop Stress & Hoop Strain for thin 10
spherical shells.
Find out the expression for Section Modulus for a i) Rectangular

40
4 Section, ii) Hollow Rectangular Section, iii) Circular Section & iv) 10
Hollow Circular Section.
5 Derive the relationship between the three modulus (Young’s, Bulk 10
& Shear).

12
The principal stresses at a point in a bar are 150 N/mm2 (tensile)
and 80 N/mm2 (compressive). Determine the resultant stress in
6 magnitude and direction on a plane inclined at 60ᵒ to the axis of 10
the major principal stress. Also, find the maximum intensity of
03
shear stress in the material at that point.
7 Derive the formulae for Crippling Load under various end 10
conditions.
03
07
01

2
 3rd SEM./MECH/AUTO/AERO/DIP IN MECH/MECH(PROD)
/MECH(MAINT)/MECH(IND INTG)/MECH(SWITCH) - 2021(W)
Th3- Engineering Materials
Full Marks: 80 Time- 3 Hrs
Answer any FIVE Questions including Q No. 1 & 2
Figures in the right-hand margin indicates marks

1. Answer ALL questions 2 x 10

a. Define Porosity.
b. What is Mild Steel?

42
c. Define unit cell.
d. What is the significance of phase diagram?
e. State two properties of spring materials.
f. Why heat treatment is needed?

12
g. State two characteristics of Duralumin.
h. Define polymerization.
i. Explain composite materials.
j. What is the function of bearing?
04
2. Answer Any SIX Questions 5x6
a. What is Spring? Discuss about different spring materials.
b. Explain Frankel Defect with figure.
03

c. Discuss about any two microconstituents of Iron & Steel.

d. Classify Composite materials. Discuss about Dispersion-
strengthened Composites.
e. State the effects of adding Nickel and Molybdenum in steel as
07

alloying elements.
f. Discuss about different bearing materials.
g Compare thermoplastic with thermosetting plastics.
01

3 Discus about any four types of mechanical properties of 10

engineering materials.
4 Discuss about various properties of plastic. 10
5 What is Tool Steel? Classify it and state its properties with 10
composition.
6 Draw Fe-C phase diagram. Explain about different phase 10
transformations.
7 Explain about different crystal structures. 10

1
 3rd Sem./MECH/AUTO/AERO/DIP IN MECH/ MECH(PROD)/
MECH(MAINT)/ MECH(IND INTG)/ MECH(SWITCH)/ 2021(W)
Th4 Thermal Engg.-1
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10

a. Define Point function and Path function.

40
b. What is mechanical equivalent of heat?
c. Define the Zeroth law of thermodynamics.
d. Explain the Clausius statement of 2nd law of thermodynamics.

12
e. State the Boyle’s law and Charles’s law.
f. Define enthalpy.
g.
07
Define Piston speed and state its formula.
h. Draw the P-V and T-S diagram of Otto cycle.
i. Define Cetane number and Octane number.
03

j. What is meant by Free Expansion?

2. Answer Any Six Questions 5X6

07

a. Explain the Thermodynamic systems.

b. Derive the steady flow energy equation.
c. Differentiate between SI and CI engine.
01

d. Classify and explain the different types of fuel.

e. Derive the relationship between Cp, Cv and R.
f. Define COP. Derive the relation between COP of Refrigerator and
COP of Heat Pump.
g An ideal gas at 30°C and 1bar is compressed adiabatically from 5m3
to 1m3. Find the temperature, pressure and work done. Take γ=1.4

1
3 Derive the efficiency of Otto cycle with P-V and T-S diagram. 10
An ideal diesel cycle operates within the temperature limits of
1700K and 300K and with a compression ratio of 16. Determine the
4 (a)pressure and temperature at each point in the cycle 10
(b)thermal efficiency of the engine
(c)mean effective pressure
Air flows steadily at the rate of 1kg/s through an air compressor
entering at 7m/s velocity, 100kPa pressure and specific volume of

40
0.95m3/kg and leaving at 5m/s, 700kPa and 0.19m3/kg. The
5 difference in internal energy between outlet and inlet is 90kJ/kg. 10
Cooling water absorbs heat from the air at the rate of 60kW.
Calculate

12
(a) rate of work input
(b) ratio of inlet and outlet pipe diameter
6 (a) What is the first law of thermodynamics? 10
(b) Derive the expression for the work done for an Isothermal process.
07
7 Explain the working principle of 2 Stroke and 4 Stroke SI engine with 10
neat sketch.
03
07
01

2
 3rd Sem. Common 2021(W)
Th-5 Environmental Studies
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

46
a. Define acid rain.
b. What is ecological succession?
c. What do you mean by soil erosion?
d. Define genetics and species.

12
e. Mention any two causes of marine pollution.
f. Define environment.
g. What is mortality?
h.
08
What do you mean by sustainable development?
i. What leads to conflicts over water?
j. Define water pollution.
03

2. Answer Any Six Questions 6x5

a. Define and explain food chain with at least one example.
b. Explain the changes caused by modern agriculture.
c. Explain Biodiversity at National level.
07

d. Give a brief note on ozone layer depletion along with its consequences.
e. Discuss in brief ‘Human Rights’.
f. Discuss the needs of public awareness towards environment.
01

g Explain cyclone disaster management.

3 Explain the effects of mine extraction on environment and tribal people. 10

4 Explain different threats to biodiversity. 10
5 Describe forest ecosystem. 10
6 Write down the causes, effects and controlling measures of soil pollution. 10
7 a Urban problems related to energy. 5
b Family welfare program. 5

1
 4TH/CIVIL/ 2022(S)
TH1 Structural Design -I

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Define modular ratio.
b. What do you mean by characteristic strength of concrete?
c. How do you determine the minimum depth of foundation?

09
d. What is curing?
e. Define Limit state. State various types of limit state.
f. Differentiate between one-way and two-way slab.
g. What is the minimum and maximum longitudinal reinforcement permissible in a column?

13
h. What do you mean by redistribution of moment?
i. Define slenderness ratio. What is its importance?
j. Draw a typical flight and show tread, riser, waist and going.
2. Answer Any SIX Questions 6x5
a. Write about advantages of LSM over WSM?
26
b. Design a short circular column to carry a service load of 1600KN use lateral ties and
helical reinforcement. The materials are M20 grade concrete and Fe415 steel.
c. Design a square footing for a RCC column 250mmx250mm carrying a load of 300KN
founded on soil that has SBC of 160KN/m2 in LSM use M20 and Fe415 steel .
07

d. A steel bar of 10mm diameter of Fe415 grade is embedded in M20 concrete. Calculate
its development length in tension and compression ( .
e. Derive the stress block parameters for flexure.
08

f. Write the assumptions made in the limit state of collapse compression.

g Explain in details why Under-reinforced section is preferred than Over reinforced
section.
3 Design a simply supported rectangular beam in flexure to resist a factored load of 10
90KN/m. Given a clear span of 6m and the size is limited to 30cm x 60cm. Use M20
01

grade concrete and Fe500 steel.

4 A bea A RCC beam of span 5m is 250mm wide 500mm deep (effective). It has 4 bars of 22mm 10
as ten tensile reinforcement. The beam carries a load of 30KN/m inclusive of self weight.
Design the beam for shear. Use M20 concrete and Fe415 steel.

5 Design a dog legged staircase for a live load of 3 KN/m2.Rise of the stair is 160mm and 10
tread is 250mm, Ceiling height is 3.5m and width of flight is 150mm use M20 concrete
and Fe415 steel.
6 Design a simply supported one way roof slab for a room 8mx3.5m clear in size if 10
superimposed load is 5 KN/m2 use M20 grade concrete a Fe415 steel.
7 Design a RCC column to resist axial factored load of 1800KN .Given column length of 3m 10
with both end fixed using M20 grade concrete and Fe415 steel.

1
 4TH SEM./CIVIL/2022(S)
Th2 Hydraulics and Irrigation Engineering
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. List out different types of rain gauges.
b. What do you mean by gross command area.
c. Write two benefits of irrigation.

08
d. What is an aqueduct.
e. Define spillway.
f. Define viscosity and its unit in C.G.S system.
g. What is the difference between laminar flow and turbulent flow.

13
h. Write down Darcy – Weisbach and Chezy's formula.
i. Differentiate between notch and weir.
j. Define duty of irrigation water.
27
2. Answer Any Six Questions 6x5
a. Define base, delta and duty and derive the relationship between
them.
b. Write different types of canal lining. What are the advantages and
07

disadvantages of canal lining.

c. Write down the effects of water logging.
d. Derive continuity equation.
e. Find the loss of head due to friction in a pipe of 1 metre diameter
08

and 15 km long. The velocity of water in the pipe is 1 meter/sec. Take

coefficient of friction as 0.005.
f. What are the causes of failure of gravity dam.
g The diameter of a pipe at sections 1-1 and 2-2 are 200 mm and 300
01

mm respectively. If the velocity of water flowing through the pipe at

section 1-1 is 4 m/sec. Find discharge through the pipe and velocity
of water at section 2-2.

3 Explain the types of cross drainage work with neat sketch. 10

4 Name the component parts of the diversion head works and state 10
their functions.
5 What is a reciprocating pump? Describe the principle and working of 10
a reciprocating pump with neat sketch.

1
6 Figure shows a circular plate of diameter 1.2 m placed vertically in 10
water in such a way that the centre of the plate is 2.5 m below the
free surface of water. Determine
(i) Total pressure on the plate
(ii) Position of centre of pressure.

08
13
27
07
08

7 The water is flowing through a taper pipe of length 100 m having 10

diameters 600 mm at the upper end and 300 mm at the lower end,
01

at the rate of 50 litres/sec. The pipe has a slope of 1 in 30. Find the
pressure at the lower end if the pressure at the higher level is
19.62N/cm2.

2
 4TH SEM./CIVIL ENGINEERING/ 2022(S)

TH3 LAND SURVEY-I

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. What is Simpson’s rule for calculation of area in survey?

56
b. What is parallax?
c. Define latitude and departure of a survey line
d. What is the principle of reciprocal levelling?

12
e. What is meant by unique identification number of parcel in map
preparation?
f. Why optical square is used in surveying?
g. What is a field book? What are the types of field books?
28
h. Convert the following WCBs to QB
a. 1600 25’
b. 2850 30’
c. 150 45’
07

d. 2030 30’
i. Define isogonic and agonic lines.
j. Why well conditioned triangles are preferred in chain surveying?
23

2. Answer Any Six Questions 6x5

a. Enlist and explain the function of each instrument used in plane table
00

surveying with neat sketch.

b. Explain about cadastral map preparation methodology.
c. The following offsets were taken from a chain line to an irregular
boundary line at an interval of 10m:
0, 2.50, 3.50, 5.00, 4.60, 3.20, 0m
Compute the area between the chain line, the irregular boundary line and
the end offsets by (a) The mid-ordinate rule & (b) The trapezoidal rule.
d. Explain the procedure to set out an angle of 300 40’ 13” with theodolite.

1
 e. A 30m steel tape was standardised at a temperature of 200 C and under a
pull of 5 kg. The tape was used in catenary at a temperature of 250 C and
under a pull of 11 kg. The cross sectional area of tape is 0.02 cm2 and its
total weight is 660 gm. Find the correct horizontal distance. Take
E=2×106kg/cm2 & α=11×10-6/ oC.
f. Explain about characteristics of contours with neat sketch.
g Differentiate between Surveyor Compass and Prismatic Compass.

56
3 Explain the procedure for solving two point and three point problems in 10
plane table surveying.
4 The following bearings were observed in traversing with a compass in an 10
area where local attraction was suspected. Find the stations affected with

12
local attraction and calculate the correct bearings of lines.
Line FB BB
0
AB 68 15’ 2480 15’
BC 148045’ 3260 15’
28
CD 224030’ 46000’
DE 2170 15’ 380 15’
EA 327045’ 147045’
07

5 Explain the procedure of chaining to overcome an obstacle where 10

chaining is obstructed but vision is free.
6 Write the procedure for finding area using Latitude and Double Meridian 10
Distance method and find out the area of a closed traverse considering
23

following data by Latitude and DMD method

SIDE LATITUDE DEPARTURE
AB +225.5 +120.5
BC -245.0 +210.0
00

CD -150.5 -110.5
DA +170.0 -220.0
7 The following consecutive readings were taken with a dumpy level along a 10
chain line at a common interval of 15m.
3.150, 2.245, 1.125, 0.860, 3.125, 2.760, 1.835, 1.470, 1.965, 1.225, 2.390,
and 3.035m.
The first reading was at a chainage of 165m where RL is 98.085. The
instrument was shifted after the fourth and ninth readings. Find RL of all
points using rise-and-fall method.

2
 4TH SEM./CIVIL/ 2022(S)
TH4 Highway Engineering

Full Marks: 80 Time- 3 Hrs

Answer any FIVE Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. What is camber ?
b. Differentiate between bitumen and tar.

00
c. What are the objectives of highway planning.
d. Define traffic density?
e. What do you mean by seal coat ?
f. Define base course and wearing course.
g. What is highway alignment?

13
h. What is function of surface drainage and sub surface drainage?
i. Define transition curve?
j. Define WBM.
29
2. Answer Any SIX Questions 6x5
a. Calculate the safe stopping sight distance for design speed of 50kmph for
( i) Two way traffic on a two lane load (ii) Two way traffic on a single lane load. Assume
coefficient of friction =0.35 & reaction time=2.5 second.
07

b. Write the objectives of providing transition curve in roads.

c. Explain the necessity of road drainage work.
d. Describe different types of bends in hill roads
08

e. Write short notes on CBR test.

f. Differentiate flexible and rigid pavement.
g Calculate the allowable speed on a horizontal curve of radius 180m. Assume the co-
efficient of lateral friction as 0.15 and maximum super elevation of 1 in 15.
01

3 What is soil stabilization, briefly explain cement stabilization? 10

4 (a)What is highway drainage? 2

(b)Explain surface drainage and subsurface drainage systems in road.
8

5 Explain typical flexible pavement failures in detail. 10

6 Explai Explain the total reaction time for a driver. 10
7 Write short notes on: 10
(a) Mud pumping.
(b) Super elevation
(c) National Highways
(b) Kerbs

1
 4TH SEM./ ELECTRICAL/ 2022(S)

TH-1 Energy Conversion-I

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10

09
a. What is the number of parallel paths in lap winding and wave winding in DC
machines?
b. What is the role of back emf in DC motor running?

c. Why breather is used in transformer?

13
d. What are the factors which affect the torque of DC motor?
e. State the two methods of improving commutation in DC Generator.
f. What do you mean by burden in instrument transformers?
26
g. State any two cooling methods of transformer.
h. What is ‘all day efficiency’ in distribution transformers?
i. Why the C.T. secondary should not be kept open?
07

j. Write any two applications of Auto transformer.

2. Answer Any Six Questions 6x5

08

a. Describe the armature control method in speed control of DC shunt Motors.

b. Write the differences between core type transformer and shell type transformer.
c. Explain the role of compensating windings in DC generator.
01

d. A 4-pole, lap wound DC shunt generator has a useful flux per pole of 0.07 Wb.
The armature winding consists of 220 turns each of 0.004Ω resistance. Calculate
the terminal voltage when running at 900 RPM if the armature current is 50 A.
e. Explain the operation of ON Load Tap changer in transformer using resistor
transition.
f. Write a short note on potential transformer (PT).

g A 25 kVA transformer has 500 turns on the primary and 50 turns on the
secondary winding. The primary is connected to 3000V, 50Hz supply. Find the
full load primary and secondary currents, the secondary e.m.f and the maximum
flux in the core. Neglect leakage drops and no load primary current.
3 Explain the saving of copper in auto transformer as compared to ordinary two 10
winding transformer.

4 The armature winding of a 4-pole, 250V DC shunt motor is lap connected. There 10
are 120 slots in each slot containing 8 conductors. The flux per pole is 20 mWb
and current taken by the motor is 25A.The resistances of armature and field
circuit are 0.1Ω and 125Ω respectively if the rotational losses amount to be
810W. Find (i) Gross torque
(ii) Useful torque and
(iii) Efficiency.

09
5 Describe the process of commutation in DC Generator along with sketch 10
diagram in details.

13
6 Explain about the care and the maintenance of transformer on daily, monthly 10
and yearly basis.

7 A 25 kW, 250V, DC shunt generator has armature and field resistances of 0.06 10
ohm and 100 ohm respectively. Determine the total armature power developed
26
when working (i) as a generator delivering 25 kW output and (ii) as a motor
taking 25 kW.
07
08
01
 4th Sem. / EEE/ELECTRICAL/ELECTRICAL(INST & CTRL)/ 2022(S)

Th2 ANALOG ELECTRONICS AND OPAMP

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

08
1. Answer All questions. 2 x 10
a. Define knee voltage of a PN junction diode. Write the values of cut
in voltage for Si and Ge diode.
b. What is the role of intrinsic (I) layer in a PIN diode?

13
c. Define ripple factor and mention its values for Half Wave and Full
Wave rectifier.
d. Draw the transistor configurations for CB, CE.
e. What are the needs for transistor biasing?
27
f. Write the advantages of negative feedback in amplifier.
g. Differentiate between BJT and FET.
h. Define CMRR and Slew Rate of an OPAMP.
i. If , then find .
07
08

j. Draw the simplified circuit diagram of a series clipper. Plot its

output waveform for an input ( )
01

2. Answer Any Six Questions 6x5

a. Explain the working of Zener diode as voltage regulator.
b. Define a filter circuit? Draw the circuit diagram of pi ( ) filter and
explain its working.
c. Draw the circuit diagram for voltage divider bias configuration.
Determine its operating point and stability factor.
d. Differentiate between voltage and power amplifier.
e. Design a subtractor using OPAMP.

1
 f. Find the h parameters of CE configuration and draw the simplified
diagram.
g Find the expressions for voltage gain of inverting and non-inverting
OPAMP.

3 With neat circuit diagram explain the working of RC coupled 10

08
amplifier with its frequency response curve.
4 With neat circuit diagram explain the working of Class – B push pull 10
amplifier.
5 Define Barkhausen Criterion for oscillation. Draw the circuit 10

13
diagrams of Colpitts and Hartley oscillator using BJT. Also specify
their frequency of oscillation.
6 Design an integrator and a differentiator using OPAMP. 10
7 Explain the working of full wave bridge rectifier. Derive the 10
27
expressions for DC and RMS values of rectifier output. Calculate its
rectification efficiency and ripple factor.
07
08
01

2
 4TH SEM /ELECT/ EEE/ 2022(S)
TH-3 Electrical Measurement & Instrumentation
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Define accuracy and sensitivity.
b. State the types of measuring instruments.
c. What are the three essential features of indicating instruments?

56
d. State the classification of moving coil instruments.
e. State the types of errors in dynamometer wattmeters.
f. Define creeping and what is its cause?

12
g. Write down two advantages of bridge circuits.
h. Define transducer.
i. State two uses of capacitive transducers.
j. What is a CRO?
28
2. Answer Any Six Questions 6x5
a. Write down the advantages of moving iron instruments.
b. Give a comparison between analog and digital multi meter.
07

c. What is a megger? Explain its construction with working principle.

d. Define Hall effect. Write some applications of Hall effect transducers.
e. State the operating principle of induction type wattmeter. Write down
the advantages and disadvantages of it.
23

f. State the applications of CRO.

g What is a thermistor? Write down the applications.

3 Explain Deflecting, controlling and damping arrangements in 10

00

indicating type of instruments.

4 Describe Construction and principle of working of Dynamometer 10
type wattmeter.
5 Explain the principle of operation and working of dynamometer type 10
single phase power factor meter.
6 Explain the construction and working principle of LVDT with a neat 10
diagram.
7 With a neat diagram, explain briefly the main parts of a cathode ray 10
tube.

1
 4TH SEM./ EEE /ELECTRICAL /ELECTRICAL(I & C) /EME / 2022(S)
Th4 Generation, Transmission and Distribution

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

00
a. What is photovoltaic effect?
b. Why transmission of electric power by high voltage DC is superior to that
of high voltage AC system?
c. State Kelvin’s law.

13
d. What are the factors affecting sag in an overhead line?
e. Write the methods of reducing corona effect?
f. What is a booster transformer?
g. Write the characteristics of Tariff.
29
h. Define diversity factor.
i. What do you mean by Ferranti effect?
j. Define voltage regulation.
2. Answer ANY SIX questions 6x5
07

a. Describe the working of Nuclear power plant with proper sketch.

b. Differentiate between EHVAC and HVDC system.
c. Explain different connection schemes of distribution system.
d. A two wire distribution AD is 225m long. The various loads and their
08

positions are given below

At point Distance from A in Concentrated load in A
meters
B 75 12
01

C 175 15
D 225 20

The cross sectional area of each conductor is 0.27 cm2. The end A is
supplied with 250 V. Resistivity of the wire is 1.78µΩ cm. Calculate the
current in each section of the conductor, the two core resistance of each
section and the voltage at each tapping point.
e. Describe Murray loop test for localization of earth fault in underground
cables.
f. Explain different types of insulator.

1
 g A generating station has following data
Installed capacity= 300 MW, capacity factor= 50%, Annual load
factor=60%, Annual cost of fuel, oil, etc= Rs. 9×107, capital cost= Rs. 109,
annual interest & depreciation= 10%. Calculate minimum reserve capacity
of the station and the cost per kWh generated?
3 a. Define Sag. 02

00
b. A transmission line has a span of 250m between supports, the 08
supports being at same level. The conductor has a cross-sectional
area of 1.29 cm2. The ultimate strength is 4220 kg/cm2 and factor
of safety is 2. The wind pressure is 40 kg/cm2. Calculate the height

13
of the conductor above ground level at which it should be
supported if a minimum clearance of 7m is to be kept between the
ground and the conductor.
4
29
A 3 phase, 50 Hz overhead transmission line has following constants 10
Resistance/phase=9.6 ohm, Inductance/phase= 0.097mH,
Capacitance/phase=0.765µF
If the line is supplying a balanced load of 24000 KVA 0.8 p.f lagging at 66
07

KV, using nominal π method Calculate

i. Sending end current
ii. Line value of sending end voltage
iii. Sending end power factor
08

iv. Percentage regulation

v. Transmission efficiency.
5 A three phase ring main ABCD fed at A at 11 KV supplies balanced loads of 10
50A at 0.8 p.f lagging at B, 120A at unity p.f at C and 70A at 0.866p.f
01

lagging at D, the load currents being referred to the supply voltage at A.

The impedances of the various sections are:
Section AB=(1+j0.6)Ω ; Section BC=(1.2+j0.9)Ω ; Section CD=(0.8+j0.5)Ω ;
Section DA=(3+j2)Ω. Calculate the currents in various sections and station
bus-bar voltages at B, C & D.
6 a. State different type of Bus-bar arrangements in substation. 03
b. Draw the layout of 66/11 KV substation. 07
7 Write short notes on 5×2
a. Necessity of EHVAC Transmission.
b. Laying of Underground cables.

2
 4TH SEM./AUTO/DIP IN MECH./MECH./MECH(IND.INTG)
/MECH(MAINT)/MECH(PROD)/MECH(SANDWICH)/ 2022(S)
Th1-Theory of Machines

Full Marks: 80 Time- 03 Hrs

Answer any five Questions including Q No.01 & 02
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Define kinematic link. Mention its types.

09
b. What is the difference between Brake and Dynamometer?
c. What is Amplitude and Time period related to vibration?
d. What is crowning of pulleys?
e. Write down the length of Open belt drive formula.

13
f. What is the function of Cam and Followers?
g. Define Co-efficient of friction.
h. What are the uses of Chain drive and Gear drive?
i. What is Vibration and Types of vibration?
j.
26
What is the function of Clutch?

2. Answer Any Six Questions 6x5

a. What is the function of bearing? Describe the roller bearing with neat
07
sketch.
b. Derive an expression for the height of Watt Governor with neat sketch.
c. Differentiate between Static and Dynamic balancing.
d. Define Velocity ratio of gear train. Derive velocity ratio of a Simple Gear
08

train with neat sketch.

e. What is four bar chain? Explain any two inversion of four bar chain.
f. What are the causes and remedies of Vibration?
g Comparison between Flywheel and Governor.
01

3 Derive the expressions for frictional torque in Pivot bearing considering 10

uniform pressure.
4 A belt is running over a pulley of diameter 120 cm at 200rpm. The angle 10
of contact is 1650and co-efficient of friction between the belt and pulley
is 0.3. If the maximum tension in the belt is 3000N. Find power
transmitted by the belt.

1
5 Describe the working of Absorption type of dynamometer. 10

6 Explain the terms: 10

(i.)Sensitivity of Governor
(ii.)Stability of Governor

09
(iii.)Isochronisms of Governor
(iv.) Ratio of Belt tension
(v.)Co-efficient of fluctuation of speed.

13
7 With neat sketch describe the Longitudinal and Torsional vibration. 10
26
07
08
01

2
 4TH SEM./MECH(IND.INT.)/ MECH(SAND)/MECH(PROD.)/
MECH(MAINT)/AERO/DME/MECH/AUTO/2022(S)
TH 2 Manufacturing Technology
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right-hand margin indicates marks
1. Answer All questions 2 x 10
a. Define superfinishing.

08
b. Explain grinding.
c. Define indexing.
d. Name four major parts of lathe machine.
e. What do you understand by quick return mechanism?

13
f. What is multiple holder?
g. Define lapping.
h. State the composition of 18-4-1 HSS tool.
i.
27
Compare drilling with boring operation.
j. Define speed and feed of cut.
2. Answer Any Six Questions 6x5
a. Why ram is used in shaper?
07

b. Explain work holding attachment in milling machine.

c. Write different parts of a slotter and their function.
d. Explain tool geometry of a single point cutting tool.
08

e. State the advantages of broaching.

f. Discuss about the tooling layout of a hexagonal bolt.
g Discuss about the functions of centreless grinder.
01

3 Name various cutting tool materials. Briefly describe one 10

important tool material along with its characteristics and uses.
4 Describe the function of different components of a shaper with 10
schematics.
5 With neat sketch explain the function of pillar drilling machine. 10
6 Explain with a neat sketch, the working of an universal dividing 10
head.
7 Describe in brief various parts of capstan and turret lathe. 10

1
 4TH SEM./MECH(SAND)/MECH(PROD)/MECH(IND.INT)/
MECH(MAINT)AERO/DME/MECHANICAL/ 2022(S)
TH-03 FLUID MECHANICS

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

Answer All questions 2 x 10

56
1.
a. Define Impact of jet.
b. What is the difference between Poise and stoke?

12
c. Explain Archimedes principle?
d. What is the difference between Notch and Weir?
e. Define discharge and its unit in S.I system.
28
f. State Darcy Weisbach and Chezy’s formula.
g. What is the statement of Pascal’s law?
h. Write down the relationship between Atmospheric pressure, Gauge
07

pressure and Absolute pressure.

i. Define Density and its unit.
j. Write down the discharge formula for rectangular weir.
23

2. Answer Any SIX Questions 6x5

a. State and derive the Continuity equation.
00

b. Define three Orifice coefficient and also derive the expression:

cd= cv x cc
c. Describe Hydraulic Gradient Line and Total Energy Line.
d. Calculate the Specific weight, Specific mass, Specific volume and
Specific gravity of a liquid having a volume of 6m3and weight of
44kN.
e. Derive an expressions for Total Pressure and Centre of Pressure for a
vertically immersed surface.
f. Describe properties of fluid.

1
 g The diameter of a pipe at the sections 1-1 and 2-2 are 200mm and
300mm respectively. If the velocity of water flowing through the
pipe at section 1-1 is 4m/sec. Find:
(i) Discharge through the pipe and
(ii) Velocity of water at section 2-2

56
3 State and prove the Bernoulli’s theorem. 10
4 The right limb of a simple U-tube manometer containing mercury is 10
open to the atmosphere while the left limb is connected to a pipe in

12
which a fluid of specific gravity 0.9 is flowing. The centre of the pipe
is 12cm below the level of mercury in the right limb. Find the
pressure of fluid in the pipe if the difference of mercury level in the
two limbs is 20cm.
28
5 (a) Derive discharge formula for triangular notch. 10
(b) Find the discharge over a triangular notch of angle 600 when
the head over the V-notch is 0.3m. Assume Cd= 0.6.
07

6 Derive force exerted & work done by the jet on a stationary (fixed) 10
vertical force.
23

7 Water is flowing through a pipe 1500m long with a velocity of 10

0.8m/sec. What should be the diameter of the pipe, if the loss of
head due to friction is 8.7m, take ‘f’ for the pipe as 0.01.
00

2
 4TH SEM./MECH/MECH(IND INTG)/ MECH(MAINT)/
MECH(PROD)/ DME/MECH(SWICH)/ 2022(S)
Th4 Thermal Engineering-II

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
(Use of steam table and mollier chart are allowed)

00
1. Answer All questions 2 x 10

a. What do you mean by calorific value of fuel?

b. Write four industrial uses of compressed air.

13
c. Define pressure ratio of air compressor.
d. Define Dryness fraction of steam.
e. State kirchoff’s law.
29
f. Define Grate for boiler.
g. What are the function of boiler mountings with example?
h. Define steam and its uses.
07

i. Carnot cycle is not used as a standard reference cycle in any steam

power plant, why?
j. Define air-fuel ratio.
08

2. Answer Any Six Questions 6x5

a. The cylinder dimensions of a single stage single acting reciprocating
01

compressor are 300mmx200mm. The compressor runs at 150r.p.m.

The intake pressure and temperature of air are respectively 1 bar
and 250c and the discharge pressure is 10bar. Determine the work
done per cycle when compression follows the law
(i) PV1.25=c
(ii) PV=c
b. What are classification of air compressors?
c. State the modes of heat transfer and explain it.
d. Give a comparison between forced draught and induced draught.

1
 e. What is the difference between Reheat cycle and Regenerative
cycle?
f. The thermal efficiency of a carnot heat engine is 60.5%. The
minimum temperature of the cycle is 250c. Find the maximum
temperature of the cycle.
g Deduce a formula for work done by a single stage single acting
reciprocating air compressor when the law of expansion is
PVn=constant neglecting clearance.

00
3 Steam is being generated in a boiler under a pressure of 12bar. Find 10
the enthalpy of 5kg of steam, when
(i) Steam is wet having dryness fraction of 0.75

13
(ii) Temperature of steam is 3000c. Take Cp= 2.1kJ/kg.

4 Describe carnot cycle with vapour with the help of P-V, T-S and H-S 10
diagrams and deduce a formula for itS thermal efficiency.
29
5 Describe the construction and working of Cochran boiler. 10
6 An engine uses 6.5kg of oil per hour of calorific value of 30,000kJ/kg. 10
07

if the B.P of the engine is 22kw and mechanical efficiency 85%.

Calculate
(i) Indicated thermal efficiency.
(ii) Brake thermal efficiency
08

(iii) Specific fuel consumption in kg/B.P/h.

7 Describe Rankine cycle with the help of P-V. T-S and H-S diagram and 10
deduce a formula for its thermal efficiency considering feed pump
01

work.

2
 5th Sem. COMMON 2020(W)

Th1- Entrepreneurship and Management & Smart Technology

Full Marks: 80 Time- 3 Hrs

Answer the questions as per the instruction.
Figures in the right hand margin indicates marks

31
1. Answer All questions 2 x 10
a. Write the full form of NABARD.

07
b. Enlist at least four characteristics of an entrepreneur.
c. Why should an entrepreneur prepare the project himself?
31
d. Define financial management.
e. Distinguish between debit and credit.
f. Define market.
03

g. Why does an organization need advertisement?

h. Differentiate a manager with a leader.
i. Define IoT.
07

j. Define IPR (Intellectual Property Right).

2. Answer Any Six Questions 5x6

01

a. Differentiate entrepreneur with manager.

b. What are the factors to be taken into account to select a technology
for an enterprise?
c. Write the objectives of financial management.
d. Write the different functions of marketing.
e. Briefly discuss different types advertising media.
f. Briefly explain the functions of HRM.
g. Briefly discuss the smart transportation system, the advantages and
 disadvantages related to it.
h. Explain the Maslow’s theory of motivation.

3 Answer any three questions 10x3

a. Briefly explain different barriers in entrepreneurship.

31
b. How do you select a business opportunity? Explain different
components (at least five) related to business opportunity.
c. What is PPR (Preliminary Project Report)? Briefly explain the
structure of PPR.
d. Explain the five functions of management briefly.

07
e. Briefly explain the general recruitment process in an organization.
f. Briefly explain different types of budgets.
31
03
07
01
 5TH SEM./ ELECTRICAL/2020(W)NEW
TH2-ENERGY CONVERSION II

Full Marks: 80 Time: 3 Hours

Answer any Five Questions including Q No. 1& 2
Figures in the right hand margin indicates marks

1. Answer all the questions 10x2

a) Define slip speed in 3 phase induction motor and state its equation.
b) What is plugging in 3 phase induction motor?
c) Define pitch factor in alternator and state its value.

8
d) What is the purpose of damper windings in alternators?

72
e) State two applications of synchronous motor.
f) What are the V-curves in synchronous motor?
g) Define step angle in stepper motor and state its value.
h) How a single phase induction motor is made self starting?
50
i) What is the function of compensated winding in compensated repulsion motor?
j) How the direction of rotation of split phase induction motor can be reversed?
40
2. Answer any six questions
6x5
a) Explain the principle of operation of synchronous motor in details.
b) Describe the power flow stages in 3 phase induction motor with a neat diagram.
c) Derive the relation between torque and rotor power factor in 3 phase induction motor.
0

d) Explain about the determination of voltage regulation of alternator by synchronous impedance method.
e) Describe about types of rotors in alternators in details.
07

f) Write a short note on capacitor start induction run motors.

g) Explain the 1-phase ON or full step operation in variable reluctance stepper motor briefly.
01

3. Derive the relationship between rotor input, mechanical power & copper loss in 3-ph induction motor. 10
4. Explain about the double field revolving theory in 1-phase induction motor with torque-slip graph. 10
5. Describe the synchronizing of 3 phase alternator using two bright and one dark lamp method. 10
6. Write a short note on (a)Direct-On-Line starter (b)Parallel operation of alternators. 10
7. Explain the effect of excitation on armature current and power factor in synchronous motor in details. 10
 5TH SEM /ELECTRICAL/ 2020(W)NEW
Th3- Digital Electronics & microprocessor
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. What do you mean by Radix of a number?
b. What is the difference between combinational and sequential logic

15
circuit?
c. What is the function of ALE in 8085 microprocessor?
d. Define modulus of a counter.

07
e. What are the various modes of 8255 programmable peripheral
interface?
f. Distinguish between a multiplexer & a demultiplexer.
g. Write down the hardware interrupts in 8085 microprocessor.
07
h. What is Race around condition in JK flip-flop?
i. Find the 2’s complement of (110101.01)2.
j. What are the various flag registers available in 8085 microprocessor?
04

2. Answer Any Six Questions 6x5

a. Explain the working of JK flip-flop with the truth table.
07

b. What is half adder? Design a full adder circuit using half-adder and OR
gate.
c. State and prove De-morgan’s theorem.
d. Discuss the various types of addressing modes of 8085 microprocessor
01

with suitable examples.

e. Explain the function of 1:4 Demux circuit with a neat diagram and write
its truth table.
f. Draw the timing diagram for MVI B, 05H.
g Write an assembly language program to add two 8-bit decimal
numbers, sum may be of 16 bits.
3 Design a 2-Bit magnitude comparator circuit and explain its operation. 10
4 Draw the functional block diagram of Intel 8085 microprocessor and 10
explain the function of each block.
5 Simplify and minimise the four variable logic expression using K map: 10
1
 f(A,B,C,D)=∑ m(0,1,2,3,5,7,8,9,10,12,13) & implement the real minimal
expression in universal logic.
6 With a neat block diagram design a traffic light controller & write an 10
assembly language program using 8255 Programmable peripheral
interface.
7 Design a 4-bit Asynchronous counter & draw its timing diagram. 10

15
07
07
04
07
01

2
 5th Sem. COMMON 2020(W)

Th1- Entrepreneurship and Management & Smart Technology

Full Marks: 80 Time- 3 Hrs

Answer the questions as per the instruction.
Figures in the right hand margin indicates marks

31
1. Answer All questions 2 x 10
a. Write the full form of NABARD.

07
b. Enlist at least four characteristics of an entrepreneur.
c. Why should an entrepreneur prepare the project himself?
31
d. Define financial management.
e. Distinguish between debit and credit.
f. Define market.
03

g. Why does an organization need advertisement?

h. Differentiate a manager with a leader.
i. Define IoT.
07

j. Define IPR (Intellectual Property Right).

2. Answer Any Six Questions 5x6

01

a. Differentiate entrepreneur with manager.

b. What are the factors to be taken into account to select a technology
for an enterprise?
c. Write the objectives of financial management.
d. Write the different functions of marketing.
e. Briefly discuss different types advertising media.
f. Briefly explain the functions of HRM.
g. Briefly discuss the smart transportation system, the advantages and
 disadvantages related to it.
h. Explain the Maslow’s theory of motivation.

3 Answer any three questions 10x3

a. Briefly explain different barriers in entrepreneurship.

31
b. How do you select a business opportunity? Explain different
components (at least five) related to business opportunity.
c. What is PPR (Preliminary Project Report)? Briefly explain the
structure of PPR.
d. Explain the five functions of management briefly.

07
e. Briefly explain the general recruitment process in an organization.
f. Briefly explain different types of budgets.
31
03
07
01
 5TH SEM /CIVIL/2020(W)NEW

Th2- Structural Design-II

Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
IS800:2007, IS 883-1970, SP 20, IS 806-1968,IS 1161-1998 and steel table are
allowed in examination.

28
1. Answer All questions 2 x 10
a. Define crinkling in tubular Steel compression member.
b. Define structural Steel.

07
c. Define gauge distance
d. What do you mean by slot weld and plug weld?
05
e. Differentiate between web buckling and web crippling of beams.
f. What is effective length of a column?
g. Define net sectional area of a tension member.
04

h. What is slenderness ratio of a masonry wall?

i. For what type of structure is the tubular Steel sections are suitable?
j. What do you mean by mortar and what are the types of mortars?
07

2. Answer Any Six Questions 6x5

a. Write down the advantages and disadvantages of steel structure.
b. Explain block shear failure in tension members.
01

c. Explain different types of butt welds with neat sketch.

d. A ground floor masonary wall is 4m clear height up to bottom of roof
slab. Height of plinth above foundation footing is equal to 0.8 metre. If
the wall thickness is 30 cm, calculate effective height and slenderness
ratio for partial restraint on both ends condition.
e. Determine the tensile strength of a roof Truss 100×75× 10 mm
connected to the gusset plate with 100 mm leg by 5 mm fillet weld
with length of weld equal to 200 mm. Take fy=250N/mm2.
f. Determine the plastic moment capacity of unsymmetrical I section.
Given specifications are:
1
 Top flange- 100 mm × 20 mm
Bottom flange- 200 mm × 20 mm
Web- 200 mm × 20 mm
g What do you mean by slip critical connection? Explain the principle of
high strength friction grip bolts.
3 Find the maximum force that can be transmitted through a double 10
bolted chain lap joint consisting of 6 bolts in two rows at pitch and
gauge distances of 40mm. Given that M16 bolts are of grade 4.6 and

28
plates of fe410 are used. The thickness of the plates connected are
10mm and 12 mm. Take end distance and edge distance as 30mm.
4 A laterally supported beam ISMB 600 @1226 N/m is placed between 10
two supports. Determine the safe uniformly distributed load the beam

07
can carry for an effective span of 8 m. Take fy=250N/mm2. Neglect
web buckling and web crippling.
5 Design a column section to carry a working axial load of 400 KN. The 10
column is 4 metre long and effectively held in position and restrained
05
against rotation at both ends. Consider fy=250N/mm2.
6 Write the codal provisions of design consideration for masonry walls 10
under eccentric loading.
7 A tie member of a roof Truss consists of two ISA 100 75,8 mm. The 10
04

angles are connected to either side of a 10mm gusset plate and the
member is subjected to a working pull of 300 KN. Design the welded
connection, assuming connections are made in workshop.
07
01

2
 5TH SEM./CIVIL ENGG./ 2020(W) NEW
TH3 RAILWAY & BRIDGE ENGINEERING
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. What do you mean by crossing?
b. Define gauge. Mention different types of gauges.
c. What is maximum value of superelevation provided in a track as per railway

15
board?
d. List the different types of rail joints
e. What do you mean by gradient?
f. Differentiate between square & skew alignment

07
g. Write Dicken's & Ryve's formula for the determination of flood discharge.
h. What is a culvert?
i. What do you mean by coffer dam?
j. Define afflux
07
2. Answer Any Six Questions 6x5
a. Write the advantages of railway
b. Mention the function of ballast.Also state the requirement of good ballast.
04

c. List the requirement of an ideal rail joint.

d. Write down the requirement & characteristics of an ideal bridge site.
e. Explain afflux with Marriman's formula and Molesworth's formula.
f. Give a brief description of various types of causeway in use.
07

g. Explain pile driving methods

3 Write the necessity of track maintenance & advantages of maintenance. 10
4 Explain various types of crossing in use on Indian Railways. 10
01

5 Describe briefly about the selection of gauge. 10

6 Describe the components of a bridge with neat sketch. 10
7 What are the different types of bridge foundation? Describe open foundation 10
and raft foundation with neat sketch.

1
 5th Sem. COMMON 2020(W)

Th1- Entrepreneurship and Management & Smart Technology

Full Marks: 80 Time- 3 Hrs

Answer the questions as per the instruction.
Figures in the right hand margin indicates marks

31
1. Answer All questions 2 x 10
a. Write the full form of NABARD.

07
b. Enlist at least four characteristics of an entrepreneur.
c. Why should an entrepreneur prepare the project himself?
31
d. Define financial management.
e. Distinguish between debit and credit.
f. Define market.
03

g. Why does an organization need advertisement?

h. Differentiate a manager with a leader.
i. Define IoT.
07

j. Define IPR (Intellectual Property Right).

2. Answer Any Six Questions 5x6

01

a. Differentiate entrepreneur with manager.

b. What are the factors to be taken into account to select a technology
for an enterprise?
c. Write the objectives of financial management.
d. Write the different functions of marketing.
e. Briefly discuss different types advertising media.
f. Briefly explain the functions of HRM.
g. Briefly discuss the smart transportation system, the advantages and
 disadvantages related to it.
h. Explain the Maslow’s theory of motivation.

3 Answer any three questions 10x3

a. Briefly explain different barriers in entrepreneurship.

31
b. How do you select a business opportunity? Explain different
components (at least five) related to business opportunity.
c. What is PPR (Preliminary Project Report)? Briefly explain the
structure of PPR.
d. Explain the five functions of management briefly.

07
e. Briefly explain the general recruitment process in an organization.
f. Briefly explain different types of budgets.
31
03
07
01
 5TH SEM./ ELECTRICAL/2020(W)NEW
TH2-ENERGY CONVERSION II

Full Marks: 80 Time: 3 Hours

Answer any Five Questions including Q No. 1& 2
Figures in the right hand margin indicates marks

1. Answer all the questions 10x2

a) Define slip speed in 3 phase induction motor and state its equation.
b) What is plugging in 3 phase induction motor?
c) Define pitch factor in alternator and state its value.

8
d) What is the purpose of damper windings in alternators?

72
e) State two applications of synchronous motor.
f) What are the V-curves in synchronous motor?
g) Define step angle in stepper motor and state its value.
h) How a single phase induction motor is made self starting?
50
i) What is the function of compensated winding in compensated repulsion motor?
j) How the direction of rotation of split phase induction motor can be reversed?
40
2. Answer any six questions
6x5
a) Explain the principle of operation of synchronous motor in details.
b) Describe the power flow stages in 3 phase induction motor with a neat diagram.
c) Derive the relation between torque and rotor power factor in 3 phase induction motor.
0

d) Explain about the determination of voltage regulation of alternator by synchronous impedance method.
e) Describe about types of rotors in alternators in details.
07

f) Write a short note on capacitor start induction run motors.

g) Explain the 1-phase ON or full step operation in variable reluctance stepper motor briefly.
01

3. Derive the relationship between rotor input, mechanical power & copper loss in 3-ph induction motor. 10
4. Explain about the double field revolving theory in 1-phase induction motor with torque-slip graph. 10
5. Describe the synchronizing of 3 phase alternator using two bright and one dark lamp method. 10
6. Write a short note on (a)Direct-On-Line starter (b)Parallel operation of alternators. 10
7. Explain the effect of excitation on armature current and power factor in synchronous motor in details. 10
 5TH SEM /ELECTRICAL/ 2020(W)NEW
Th3- Digital Electronics & microprocessor
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. What do you mean by Radix of a number?
b. What is the difference between combinational and sequential logic

15
circuit?
c. What is the function of ALE in 8085 microprocessor?
d. Define modulus of a counter.

07
e. What are the various modes of 8255 programmable peripheral
interface?
f. Distinguish between a multiplexer & a demultiplexer.
g. Write down the hardware interrupts in 8085 microprocessor.
07
h. What is Race around condition in JK flip-flop?
i. Find the 2’s complement of (110101.01)2.
j. What are the various flag registers available in 8085 microprocessor?
04

2. Answer Any Six Questions 6x5

a. Explain the working of JK flip-flop with the truth table.
07

b. What is half adder? Design a full adder circuit using half-adder and OR
gate.
c. State and prove De-morgan’s theorem.
d. Discuss the various types of addressing modes of 8085 microprocessor
01

with suitable examples.

e. Explain the function of 1:4 Demux circuit with a neat diagram and write
its truth table.
f. Draw the timing diagram for MVI B, 05H.
g Write an assembly language program to add two 8-bit decimal
numbers, sum may be of 16 bits.
3 Design a 2-Bit magnitude comparator circuit and explain its operation. 10
4 Draw the functional block diagram of Intel 8085 microprocessor and 10
explain the function of each block.
5 Simplify and minimise the four variable logic expression using K map: 10
1
 f(A,B,C,D)=∑ m(0,1,2,3,5,7,8,9,10,12,13) & implement the real minimal
expression in universal logic.
6 With a neat block diagram design a traffic light controller & write an 10
assembly language program using 8255 Programmable peripheral
interface.
7 Design a 4-bit Asynchronous counter & draw its timing diagram. 10

15
07
07
04
07
01

2
 5th Sem. COMMON 2020(W)

Th1- Entrepreneurship and Management & Smart Technology

Full Marks: 80 Time- 3 Hrs

Answer the questions as per the instruction.
Figures in the right hand margin indicates marks

31
1. Answer All questions 2 x 10
a. Write the full form of NABARD.

07
b. Enlist at least four characteristics of an entrepreneur.
c. Why should an entrepreneur prepare the project himself?
31
d. Define financial management.
e. Distinguish between debit and credit.
f. Define market.
03

g. Why does an organization need advertisement?

h. Differentiate a manager with a leader.
i. Define IoT.
07

j. Define IPR (Intellectual Property Right).

2. Answer Any Six Questions 5x6

01

a. Differentiate entrepreneur with manager.

b. What are the factors to be taken into account to select a technology
for an enterprise?
c. Write the objectives of financial management.
d. Write the different functions of marketing.
e. Briefly discuss different types advertising media.
f. Briefly explain the functions of HRM.
g. Briefly discuss the smart transportation system, the advantages and
 disadvantages related to it.
h. Explain the Maslow’s theory of motivation.

3 Answer any three questions 10x3

a. Briefly explain different barriers in entrepreneurship.

31
b. How do you select a business opportunity? Explain different
components (at least five) related to business opportunity.
c. What is PPR (Preliminary Project Report)? Briefly explain the
structure of PPR.
d. Explain the five functions of management briefly.

07
e. Briefly explain the general recruitment process in an organization.
f. Briefly explain different types of budgets.
31
03
07
01
 5TH SEM/MECH/MECH(MAIN.)/MECH.(PROD.)/MECH(IND.INT)/
MECH(SAND)/ 2020(W)NEW
Th-2 Design of Machine Elements

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Define factor of safety
b. State function of shaft.
c. What is a key? State its function.
d. What are the materials used for helical spring?
e. What is modulus of rigidity?
f. What is surge in springs?

8
g. What is the difference between toughness and stiffness?
h. What are the different types of shaft couplings?

72
i. Define Diagonal pitch.
j. What is welded joint? Write two application of welded joint.

2. Answer Any Six Questions 6x5

a. What are the advantages of welded joint over riveted joints?
50
b. Explain mechanical properties of the material.
c. Draw stress-strain diagram for mild-steel. Explain various points.
d. Explain the failures of a riveted joint.
e. A plate 100mm wide and 12.5mm thick is to be welded to another plate by means of
40
parallel fillet welds. The plates are subjected to a load of 50KN. Find the length of the
weld so that the maximum stress does not exceed 56mpa. Consider the joint first under
static loading and then under fatigue loading.
f. How are the keys classified? Draw neat sketches of different types of keys and state
their applications.
0

g. A line shaft rotating at 200r.p.m is to transmit 20kW. The shaft may be assumed to be
made of mild steel with an allowable shear stress of 42mPa. Determine the diameter of
07

the shaft, neglecting the bending moment on the shaft.

3 Design a clamp coupling to transmit 30kW at 100r.p.m The allowable shear stress for 10
the shaft and key is 40mPa and the number of bolts connecting the two halves are six.
The permissible tensile stress for the bolts is 70mPa. The co-efficient of friction
01

between the muff and the shaft surface may be taken as 0.3.
4 Describe the Design procedure in details. 10
5 A helical spring is made from a wire of 6mm diameter and has outside diameter of 10
75mm. If the permissible shear stress is 350mpa and modulus of rigidity 84kN/mm2.
Find the axial load which the spring can carry and the deflection per active turn.
6 Two plates of 10mm thickness each are to be joined by means of a single riveted double 10
strap butt joint. Determine the rivet diameter; rivet pitch, strap thickness and efficiency
of the joint. Take the working stresses in tension and shearing as 80mPa and 60mPa
respectively.
7 Design the rectangular key for a shaft of 50mm diameter. The shearing and crushing 10
stresses for the key material are 42mPa and 70mPa.
 5TH SEM./ DIP.MECH/ MECH(MAIN)/ MECH(PROD) /MECH(SAND)
/MECH /MECH (IND.INT) /MECH(AUTO)/ 2020(W) NEW
Th3-Hydraulic Machines & Industrial Fluid Power
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Write down the definition of hydraulic turbine and give one example.
b. What is the mathematical formula for hydraulic efficiency of Francis turbine?
c. Write the formula for speed ratio of Kaplan turbine.

15
d. Define about suction lift and delivery lift for centrifugal pump.
e. Define about hydraulic pump.
f. Define positive slip and negative slip for reciprocating hydraulic pump.
g. Why air regulator is used in the pneumatic control system?

07
h. What is the function of flow control valve in pneumatics?
i. Write the purpose of using actuators in hydraulic control system.
j. Draw symbols for bi-directional motor and check valve of hydraulic control.
2. Answer Any Six Questions 6x5
07
a. Distinguish between impulse and reaction turbine.
b. Write a short note about working of centrifugal hydraulic pump.
c. A single acting reciprocating pump running at 100 rpm delivers 0.012 m3/sec of
water. The diameter and stroke of the cylinder are 0.2 m and 0.3 m respectively.
04

Calculate the coefficient of discharge and percentage of slip.

d. Explain briefly about air lubricator.
e. Write down short note on single-acting cylinder for pneumatic control.
f. Write about the advantages and limitations of hydraulic system.
07

g. Write briefly about direct acting relief valve.

3 The mean bucket speed of a pelton wheel is 10 m/s. Jet of water flows at the rate 10
of 0.8 m3/sec under a head of 35m. The buckets deflect the jet through an angle of
1650. If the coefficient of velocity of the jet is 0.98, then find power developed by
01

water in the turbine and hydraulic efficiency of turbine.

4 Find the manometric efficiency and vane angle at inlet of a centrifugal pump 10
3
delivering water at the rate of 0.2 m /s against a total head of 80m. The pump
runs at 1450 rpm. The inner and outer diameter of the pump are 25 cm and 50 cm
respectively. The area of flow through the impeller is 0.08m2. The vanes are
curved in backward direction at an angle of 300 at exit.
5 Explain in detail about construction and working of double acting reciprocating 10
pump with neat sketch.
6 Explain in detail about 3/2 DCV and 5/2 DCV with proper diagrams for pneumatic 10
control systems.
7 Explain about external and internal gear pumps used in hydraulic controls. 10
1
 5th Sem. COMMON 2020(W)

Th1- Entrepreneurship and Management & Smart Technology

Full Marks: 80 Time- 3 Hrs

Answer the questions as per the instruction.
Figures in the right hand margin indicates marks

31
1. Answer All questions 2 x 10
a. Write the full form of NABARD.

07
b. Enlist at least four characteristics of an entrepreneur.
c. Why should an entrepreneur prepare the project himself?
31
d. Define financial management.
e. Distinguish between debit and credit.
f. Define market.
03

g. Why does an organization need advertisement?

h. Differentiate a manager with a leader.
i. Define IoT.
07

j. Define IPR (Intellectual Property Right).

2. Answer Any Six Questions 5x6

01

a. Differentiate entrepreneur with manager.

b. What are the factors to be taken into account to select a technology
for an enterprise?
c. Write the objectives of financial management.
d. Write the different functions of marketing.
e. Briefly discuss different types advertising media.
f. Briefly explain the functions of HRM.
g. Briefly discuss the smart transportation system, the advantages and
 disadvantages related to it.
h. Explain the Maslow’s theory of motivation.

3 Answer any three questions 10x3

a. Briefly explain different barriers in entrepreneurship.

31
b. How do you select a business opportunity? Explain different
components (at least five) related to business opportunity.
c. What is PPR (Preliminary Project Report)? Briefly explain the
structure of PPR.
d. Explain the five functions of management briefly.

07
e. Briefly explain the general recruitment process in an organization.
f. Briefly explain different types of budgets.
31
03
07
01
 5TH SEM/MECH/MECH(MAIN.)/MECH.(PROD.)/MECH(IND.INT)/
MECH(SAND)/ 2020(W)NEW
Th-2 Design of Machine Elements

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Define factor of safety
b. State function of shaft.
c. What is a key? State its function.
d. What are the materials used for helical spring?
e. What is modulus of rigidity?
f. What is surge in springs?

8
g. What is the difference between toughness and stiffness?
h. What are the different types of shaft couplings?

72
i. Define Diagonal pitch.
j. What is welded joint? Write two application of welded joint.

2. Answer Any Six Questions 6x5

a. What are the advantages of welded joint over riveted joints?
50
b. Explain mechanical properties of the material.
c. Draw stress-strain diagram for mild-steel. Explain various points.
d. Explain the failures of a riveted joint.
e. A plate 100mm wide and 12.5mm thick is to be welded to another plate by means of
40
parallel fillet welds. The plates are subjected to a load of 50KN. Find the length of the
weld so that the maximum stress does not exceed 56mpa. Consider the joint first under
static loading and then under fatigue loading.
f. How are the keys classified? Draw neat sketches of different types of keys and state
their applications.
0

g. A line shaft rotating at 200r.p.m is to transmit 20kW. The shaft may be assumed to be
made of mild steel with an allowable shear stress of 42mPa. Determine the diameter of
07

the shaft, neglecting the bending moment on the shaft.

3 Design a clamp coupling to transmit 30kW at 100r.p.m The allowable shear stress for 10
the shaft and key is 40mPa and the number of bolts connecting the two halves are six.
The permissible tensile stress for the bolts is 70mPa. The co-efficient of friction
01

between the muff and the shaft surface may be taken as 0.3.
4 Describe the Design procedure in details. 10
5 A helical spring is made from a wire of 6mm diameter and has outside diameter of 10
75mm. If the permissible shear stress is 350mpa and modulus of rigidity 84kN/mm2.
Find the axial load which the spring can carry and the deflection per active turn.
6 Two plates of 10mm thickness each are to be joined by means of a single riveted double 10
strap butt joint. Determine the rivet diameter; rivet pitch, strap thickness and efficiency
of the joint. Take the working stresses in tension and shearing as 80mPa and 60mPa
respectively.
7 Design the rectangular key for a shaft of 50mm diameter. The shearing and crushing 10
stresses for the key material are 42mPa and 70mPa.
 5TH SEM./ DIP.MECH/ MECH(MAIN)/ MECH(PROD) /MECH(SAND)
/MECH /MECH (IND.INT) /MECH(AUTO)/ 2020(W) NEW
Th3-Hydraulic Machines & Industrial Fluid Power
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10
a. Write down the definition of hydraulic turbine and give one example.
b. What is the mathematical formula for hydraulic efficiency of Francis turbine?
c. Write the formula for speed ratio of Kaplan turbine.

15
d. Define about suction lift and delivery lift for centrifugal pump.
e. Define about hydraulic pump.
f. Define positive slip and negative slip for reciprocating hydraulic pump.
g. Why air regulator is used in the pneumatic control system?

07
h. What is the function of flow control valve in pneumatics?
i. Write the purpose of using actuators in hydraulic control system.
j. Draw symbols for bi-directional motor and check valve of hydraulic control.
2. Answer Any Six Questions 6x5
07
a. Distinguish between impulse and reaction turbine.
b. Write a short note about working of centrifugal hydraulic pump.
c. A single acting reciprocating pump running at 100 rpm delivers 0.012 m3/sec of
water. The diameter and stroke of the cylinder are 0.2 m and 0.3 m respectively.
04

Calculate the coefficient of discharge and percentage of slip.

d. Explain briefly about air lubricator.
e. Write down short note on single-acting cylinder for pneumatic control.
f. Write about the advantages and limitations of hydraulic system.
07

g. Write briefly about direct acting relief valve.

3 The mean bucket speed of a pelton wheel is 10 m/s. Jet of water flows at the rate 10
of 0.8 m3/sec under a head of 35m. The buckets deflect the jet through an angle of
1650. If the coefficient of velocity of the jet is 0.98, then find power developed by
01

water in the turbine and hydraulic efficiency of turbine.

4 Find the manometric efficiency and vane angle at inlet of a centrifugal pump 10
3
delivering water at the rate of 0.2 m /s against a total head of 80m. The pump
runs at 1450 rpm. The inner and outer diameter of the pump are 25 cm and 50 cm
respectively. The area of flow through the impeller is 0.08m2. The vanes are
curved in backward direction at an angle of 300 at exit.
5 Explain in detail about construction and working of double acting reciprocating 10
pump with neat sketch.
6 Explain in detail about 3/2 DCV and 5/2 DCV with proper diagrams for pneumatic 10
control systems.
7 Explain about external and internal gear pumps used in hydraulic controls. 10
1
 5TH SEM./ COMMON / 2022(W)

Th-1 ENTREPRENEURSHIP AND MANAGEMENT & SMART

0 1
TECHNOLOGY
1 9 12
Full Marks: 80
20 3
Answer any five Questions including Q No.1& 2
Time- 3 Hrs

2 30
Figures in the right-hand margin indicates marks.

1 - 20
1.
a. 1 3 20
Answer All questions
Name two barriers in entrepreneurship.
2 x 10
2
1 9 1
b.
0
Write two advantages of preliminary project report.
2
2

191
c. Write two techniques /models of inventory management. 2
d.
2 0 3
How does branding helps manufacturers, retailer and consumers? 2

30
e. Name two symptoms of bad management. 2
f.
2 0 2
Write two primary responsibilities of Human Resource Department in an 2

2 0 1-
industry.
2 0 1
1
g.
3 Write two functions of a leader.
1 9 1 2

19 h. Name four personal protective equipment used in industry.

0 3 2
i. Write two applications of break-even analysis.
30 2 2
j.
2
Write two applications of smart agriculture. 2
2.
a.
Answer Any Six Questions
01 -20
Compare between an entrepreneur and manager
6x5
5
32 1
191
b. Write a short note on a successful Indian Entrepreneur. Mention any five 5
quality in him/her.
12 0
c. 1 9
Explain the role of District Industry Center in promoting enterprises. List
3 5
2 0
any five supports provided by DIC to entrepreneur.
0
d.
2 3
What are the parameters used to decide the plant capacity in a project? 5
e.
- 20
What is TQM? Explain the need of TQM in small enterprises.
1 0 1 5
f. 0
Write any five safety provisions in Factory Act,1948?
2 1 9 12 5
3 0 1
1911912
g Explain the techniques of motivation. 5
0 3
2with example.
3 3
0 b. Explain the success story of an Indian start02up.
a. What is Technology Business Incubator? 3
Explain0 10
3 02 2feasibility report.
05
4 2 Explain the components of Techno 1
economic
-
0 inventory control in 10
1 -2 3 2
2 0 Explain delivery schedule,
1 9 1
market need and 10

13
production planning and control.
6 Write the Concept of IoT and how does it work. 10
7 Explain the management of working capital 10

1
 5TH SEM./ DIP. IN MECH./ MECH(MAINT)/ MECH(PROD)/ MECH(SAND)/
MECHANICAL/ MECH(IND. INT) / 2022(W)
4 5
8 01
Th2 Design of Machine Elements
1
20 4
Full Marks: 80
Answer any 2 0
3 Questions including Q No.1& 2
five
Time- 3 Hrs

-
Figures2 0
in the right hand margin indicates marks

2 0 1 DATA BOOKS ALLOWED

1. Answer9 1 3
All questions 2 x 10
1 5
4and Pitch?
a. What is meant by Spring Rate
b. Define the term: Factor 8 0 1
of Safety.
c. What is Modulus of 0 1
4Rigidity?
d. What are the 3 2
0different types of keys?
e. What is 0
2 2
rivet? State its uses.
1
f. Define
0 - welding and types of welding process. 4 5
3
g. 2What is the pressure vessel? 8 0 1
1
19 h.i. What 4
is spring? Classify spring into its various types. 1
State the formula for stress in helical spring 0 0
2of a circular wire.
j. State four general considerations in0Machine 2 3 design.
1 - 2
2. Answer Any Six Questions20 6x5
a. What is the function 9 3
1of shaft coupling? 4 5
Describe requirements of a
good shaft coupling. 1 8 0 1
b. Explain the failures of a riveted
0 4 1joint.
3 2
c. Describe the mechanical0properties of the material.
d. Two plates of 10mm
0 2 thickness each are to be joined by means of a
2 strap butt joint. Determine the rivet diameter,
single riveted -
1 double
1 4 5
2
rivet pitch,
3 0 5
strap thickness of the joint. Take the working stresses
8 0
9 1 0and
intension 1 4shearing as 8MPa and 60MPa respectively.41
1 8
e. A line1shaft rotating at 200 rpm is to transmit 20kW.
0 2 0The shaft may
2 0
be 4assumed to be made of mild steel with an2allowable 3 shear stress
3 0 0
of 42MPa. Determine the diameter of-2the shaft neglecting the
2 02 0 1
1 - bending moment on the shaft.
1 3 2disadvantages of Welded Joints
32 0 f. Briefly explain the
over Riveted Joints.
advantages
1 9 and
1 g State the application of Saddle keys, Tangent keys, Round keys,
Splines keys and Woodruff keys with neat sketches.

1
 4 5
1 801
3 2
Design and make a neat dimensioned0 4 sketch of a muff coupling 10
0
which is used to connect3two steel shafts transmitting 40kW at 350
2the shafts and key is plain carbon steel for
rpm. The material2for
- 0
2 0
which allowable 1 shear and crushing stresses may be taken as 40MPa
1
and 80MPa
9 3 respectively. The material for the muff is cast iron for
1 the allowable shear stress
which
4 5 may be assumed as 15MPa.
0 1
8 compression spring for a service load
Design a close coiled1helical
4
ranging from 2250N2 0 4to 2750N. The axial deflection of the spring for
10

2 3
the load range
0 is 6mm. Assume a spring index of 5. The permissible
0
shear-2stress intensity is 420MPa and modulus of 5 rigidity
2 0 1
G=84kN/mm 2
1
. Neglect the effect of shear concentration.4Draw a fully
1 0
3 dimensioned sketch of the spring showing details18of the finish of the
1 9 end coils. 0 4
5 Write down the general Procedure followed 3 0 2 in Machine Design. 10
0 2
2 thick is to be welded to another
6 A plate 100mm wide and 12.5mm0 1 - 10
3
plate by means of parallel 2 5 so that the maximum
fillet welds. The plates are subjected to a
1 length of the14weld
load of 50kN. Find 1 9the 0 the joint first under static
8
stress does not exceed 56MPa.1Consider
4
loading and then under fatigue
0 2 0 loading.

0 2 3
7
1 - 2
Design the rectangular key for a shaft of 50mm diameter. The
crushing stresses for the key material are 42MPa1and 4 5 10

3 2 0
shearing and
5 8 0
70MPa. 4 1
1911801 0 2 0 4
2 0 4 2 3
3 0 - 2 0
2 0 2 0 1
1 - 1 3 2
2 0 1 9
13

2
 5TH SEM./ DIP. MECH /MECH(MAINT.)/MECH(PROD.)/ MECH(SAND)
4 7
MECHANICAL/ MECH. ENGG(IND. INT.)/ 2022(W)

1 8 14
Th-3
6
Hydraulic Machines & Industrial Fluid Power
20
Full Marks: 80
2 3 0 Time- 3 Hrs
Answer any
- 2 0five Questions including Q No.1& 2
2 0 1 in the right hand margin indicates marks
Figures
1.
9 3 questions
Answer1All 2 x 10
1 turbines. 4 7
a. Classify
8 1 4
0 6 1
b. Define a Pneumatic system.
2
0 of a turbine?
c. What is the function
3
0 2
d. Define2mechanical
0 1 - efficiency of a pump.
47
e. 2What
3 pump? do you understand by negative slip in a 1
8 4
reciprocating
9 1
1 f. Define hydraulic efficiency of a turbine. 20 61
2 3 0a pneumatic circuit
g. Name the following components used
- 2 0 in
i)
2 0 1 ii)

1 3 4 7
19 8 14
h. Name four important components
0 61 of a hydraulic system.
i. Define a pump. Classify 3 0 2
it.
2 0 2
1 -
j. Define fluid power.
4 4 7
3 2 0 7 8 1
2.
91 8Any
Answer
1 4
4Six Questions 6 1 6x5
1 1 0 2 0
0 6
a. Discuss
3
about the direct control of single acting cylinders.
2
b.02Compare impulse turbine with reaction turbine. 2 0
2 3
0 c. Write down the Operation of 2Double 1 -
-2 3 0 Acting Cylinder with
2 0 1 metering in control with sketch.9 1
13 1
d. Why priming is necessary in a Centrifugal Pump?
e. Compare Hydraulic systems with pneumatic systems.

1
 4 7
1 8 14
20 6
2 3 0
f.Derive the expression
- 2 0 for discharge through a Single Acting

2 0 1
Reciprocating Pump and work done by it.

g Discuss
3
91about 3/2 Directional 7Control Valves used in hydraulic
1 4
circuit.
8 1 4
0 6 1
3 A single acting 2 reciprocating pump, running at 50 rpm, delivers 10
0.015 m /s3
2 3 0
of water. The diameter of the piston is 180 mm and
-
stroke 2 0 350 rpm. Determine the a) Theoretical discharge
length
7 of
2 0
the1 pump, b) Co-efficient of discharge and c) Slip 4 4and the
1 3 percentage slip of the pump. 1 8 1
149 6
Discuss briefly about various components of0a pneumatic control 10
system. 30 2
5 Discuss about internal and external2 0 2
gear pumps used in hydraulic 10
systems with neat sketch. 1 -
0bucket speed of 8 m/s with a jet of 10
6 A Pelton wheel has a mean3 2
water flowing at 1 the 47 a head of 25 meters.
91rate of 650 lit/s14under
1
The buckets deflect the jet through
6 8 an angle of 160ᵒ. Calculate
the power given by water
2 0 to the runner and the hydraulic
0Assume co-efficient of velocity as 0.97.
Write short notes0 2
on:
3
efficiency of the turbine.
7
a) Cavitation1 - 2 4
10
7
0
2 Valve
7 8 1 4
9 1 3
b)Throttle
4 4 6 1
1
c) 1 in turbine
Draft Tube
1 8 2 0
0 6
d) Hydraulic Accumulator
2 30
3 02 2 0
0 2 0 1 -
1 -2 3 2
2 0 1 9 1
1 3

2
 5TH SEM./ AUTO/DIP MECH ENGG/ MECH(MAINT) /MECH(PROD)
/MECH(SAND)/MECH(IND.INT) /MECHANICAL / 2022(W)
5 9
Th4 7 49
Mechatronics
1
Full Marks: 80
0 7
2hand margin
Time- 3 Hrs
0
Answer any five Questions
Figures in the3right
2
including Q No.1& 2
indicates marks

- 2 0
1. 2 0
Answer All questions
1 2 x 10
3
91various applications of Mechatronics.
a. Define Mechatronics.
b. State1the 5 9
7 9
4 actuators.
c. List the various types of the mechanical
d. Write down the advantages
0 7 1 of PLC.
e. Define and classify2
f. What is meant 2 3 0 transducer.
by mnemonics?
g. State-the
0
2 uses of PLC. 9
2 0 1 9 5
1
h. State the functions of robotics.
i.3 Write down the advantages and disadvantages of robots.17
4
19 j. State the uses of worm gear? 2 0 7
2 3 0
2. Answer Any Six Questions
- 2 0 6x5
a. List the components of a mechatronic
2 0 1 system and explain their functions.
b. Define sensor and explain the
9 1 3 working of motion 5 9sensor.
c. Explain the working 1 of solenoid.
4 9
d. Discuss the working of master and jump7controller.
0 7 1
e. Explain the software and hardware
f. Write down the difference 3 0 2 switches and relays.
between
components of CAD/CAM.

2 0 2
g Discuss the laws of robotics.
1 - 9 5 9
3 2 0
details9the architecture of PLC with a neat diagram. 7 4
3 Describe
1 in
9a detailed
4 5
9 classification of Industrial Robots. 7 1 10
4
1
Give
Write1
7 0 2 0 10
5
2 7 short note on:
0 1) Light sensor 2 3 10

3 0 - 2 0
2 06 2 2) Stepper motor
What is meant by drives in CNC? Explain 2
1
0different types of drives present in 10
0 1 - 1 3 the

2 CNC machine.
1 9
13 7 What are the different types of electromechanical transducer? Discuss in details. 10

1
 5TH SEM /MECHANICAL/ MECH(MAIN)/ MECH(PROD)/ MECH(SAND) /
DIP IN MECH/ MECH(INDUSTRY INTEGRATION)/ 2022(W)
2 4
15
TH-5 Refrigeration & Air Conditioning
Full Marks: 80
8 1 6 Time- 3 Hrs
Answer any five Questions
2 0 including Q No.1& 2
0 hand margin indicates marks
Figures in the 3 right
0 2
PSYCHOMETRICS
2 CHARTS ALLOWED
1.
0
Answer All questions 1 - 2 x 10
3
a. What is sensible
1 2 heat factor?
b. Discuss
1 9 about closed system Brayton Cycle.
4
c. State the unit of refrigerating effect.
1 5 2
d. What is saturated air?
e. How does an air filter work?
8 1 6
f. Define refrigeration.
0 2 0
g. What is moist3 air?
2 0 2
h. What is humidity ratio?
i. What
0 -
1adocomfort
you understand by human comfort? 2 4
j. 2Why
3 chart is recommended?
6 1 5
1
12.9 a. Answer 8 1
Any Six Questions
What do you mean by wet bulb temperature? 0 0
2Explain how it is different
6x5

from dew point temperature.

0 2 3
b. Describe different components of a simple
1 - 2 vapour compression refrigeration
system.
3 2 0
1
d. Discuss in brief about the 9 1filters and fans used52in4air-conditioning system.
c. Classify air-conditioning system.

0
e. Air at 40 C has a relative humidity of 98%.
1 6 1 What is dew point temperature?
What mass of liquid water per kg
0
2 0 8 of dry air will result if the moisture is

f. State the factors considered

2 0
cooled to 8 C at constant pressure of 85KPa.
3 while selection of a refrigerant for a system.
g Differentiate between
- 0
2 summer air-conditioning system and winter air-24
0 41
conditioning system
2 1 5
3 1
Explain 3briefly2with a neat diagram the working of a practical1 vapour 10
5 8 6
1 9 6
absorption 1system.
2 0
1kg8 of1air at a pressure of 1.2bar and a temperature of 18 0 0
4
2 3 C is compressed to 10
0 It is then cooled to 25 C in the cooler before02entering the expansion
0

2 3 0 5.5bar.
- 2 as isentropic processes,
2 0
cylinder. Assuming compression and expansion
1
determine the refrigerating effect per kg2of0air and theoretical COP. Take C
0 1 - = 1.0 & γ=1.4. 1 3 p

32 5 Describe in detail the summer air 1 9

conditioning system with neat sketch. 10
1 6 How the load for air-conditioning is calculated? What are the factors which 10
are to be considered while evaluating the heat gains?
7 A sling psychrometer recorded WBT and DBT as 220C and 280C. Calculate the 10
Vapour Pressure, Degree of saturation, Relative humidity and Specific
humidity.
1
 VI-Sem/CI V lL/2UI9(S)(New)

RAILWAY AND BRIDGE ENGINEERING

(Code: CET-603)
Full Marks: 70 Time: 3 hours
Answer any five questions
Figures in the 'right-hand margin' indicate marks
..
·1.. (a) Define cart. 2
(b) Write the advantages of railway. 5
(c) Describebriefly about the selection of gauge. 7
. "

2. (a) What is the maximum value of super elevation provided in a track as per
railway board? 2
(b) Wh~t are the different types of rails ? Write the functions of rail. 5
(c)" Prepare a-neat sketch of a typical cross-section of an embankment with the"
ballast section 'for a single-line or double-line broad gauge. 7

3~ (a)' What do you mean by gradient? 2

(b) Explain the functions and requirements of sleepers.
•.. '. •.... ,! . ".,--" ;...
.•.•.
5
. (c) Explain various types of crossing ill use on Indian Railways. 7

4. (a) What-do you"mean by crossing? 2

(b) List the requirements of an ideal rail joint. 5
(c) Write the necessity of maintenance and advantages of maintenance. 7

5. (a) Define cross drainage. 2

(b) Write the requirement of an"ideal bridge, 5
(c) List out various design data to be collected and the purpose of surface investi-
gation for construction of bridge. 7

6. (a) Whatis a culvert ?" 2

(b) Give brief description of various types of causeway in use. 5·
(c) Mention and explain the general principles of the design of bridge foundations. 7
I .

7.' (a) What do you mean by coffer dam ? 2

(b) Classify and describe briefly each classification of steel and concrete bridge. 5
(c) Write down the functions and explanatory notes for the typesof piers, 7.

VT-I.62~

._-- --. ----

Total Pages- 2 VI- Sem/CIVIL/2019(S)(New)

ADVANCED CONSTRUCTION TECHNIQUES AND EQUIPMENTS

(Code: CET-605(E-iii) )
Full Marks : 70 Time: 3 hours
Answer any five questions
Figures in the right-hand margin indicate marks

1. (a) What do you mean by workability of concrete. 2

(b) What are the durability requirement of concrete as per IS 456? 5
(c) What are different methods for measuring workability and explain anyone
method? 7

2. (a) Define light intensity? 2

(b) Describe the types of wiring ? 5
(c) Explain the factors influencing the choice of mix proportions? 7

3. (a) What do you mean by fibers? 2

(b) Describe briefly the structural irregularities. 5
(c) Write down short notes on any two: 7
(i) PVC
(i i) Cladding
(iit) Geo-synthesis.

4. (a) What is the unit of measurement of intensity oflight? 2

(b) Describe briefly different types of roller ? 5
(c) What do you mean by earthing? Describe different types of earthing? 7

5. (a) What is ventilation? 2

(b) State general principles for central plants layout for hot water supply. 5
(c) Describe the different additional strengthening measures that are adopted in
Masonry building for earthquake resistance? 7

6. (a) What is retrofitting of structures? 2

(b) Define any two: 5
(i) Acoustic material
(ii) Soil reinforcing
(iii)RPVC

(TurnOver)
 ( 2 )

(c) Describe different methods of ventilation. 7

7. (a) What is dragline ? 2

(b) Describe different earth-moving and compacting equipments indicating their
specific uses. 5
(c) What are the sources of weakness in RCC framed building? 7

VI- SemlCIVIIl20 19(5)(NewXCEf -605(E-iii)) VI'-1,720

 .. VI-Sem/CIVIL/2019(S)(New)
Total Pages - 2

SlRUCTURAL DESIGN-II
(Code: CET-602)
Full Marks : 70 Time: 3 hours
Answer any five questions
Figures in the right-hand margin indicate marks
Steel Table and Code books are allowed which are related to this design
Le.-IS800-2007 & etc.

1. (a) Wharare the types of structural steel? 2

(b). Mention the advantages and disadvantages of using steel structures. 5
(c) Find the maximum force that can be transmitted through a double bolted chain
lap joint consisting.of 6 bolts in 2 rows. Given that MI6 bolts of grade 4·6 and
plates ofFe410 are used. If the following datas are given, .
Thickness of plate tl = 10 mm, t2 = 12 mm
Diameter of bolt d = 16 mm, pitch P = 60 mm, Edge distance' e' = 30 mm
Width of the plate' b' = 160 mm,i, = 250 Mpa. 7

2. (a) Define the following term with diagram: 2

i i ch of the bolts
(ii) Gauge distance
(iii)Edge distance
(iv) Staggered pitch.
(b) A steel plate 200 mm x 12 mm is welded to a 10 mm thick gusset plate such that
the overlap of the member is 300 mm. If fillet weld of size 6 mm is used for
the connection, determine the design strength of the joint. Given that shop
welding is to be done on three sides and grade of steel is Fe410. . 5
(c) Design a lap joint for two plates of size 120 mm x 10 mm and 120 mm x 12 mm
for maximum efficiency. Assume shop welding ana Fe410steel. 7

~. (a) Mention two disadvantages of welding. 2

j

(b) A tension member consists of a flat 100 mm x 10 mm which is connected to

a gusset plate 10 mm thick by 2 nos. of 16 mm diabolts. If steel of grade Fe410
and bearing bolts of property class 4·6 are used in the workshop, determine the
strength of the flat against yielding, rupture and block shear. Also determine the
maximum load the joint can carry safely. 5
(c) Calculate factored axial load on the column. section. ISHB 400 @ 806·38 NIM.
The height of the column is 3·5 m 2nd it is pin-ended. Use steel ofFe41o grade. 7

4. (a) Define effective length and slenderness ratio ofa column. 2

(Turn Over)
 ( 2 )

(b) Determine the plastic moment capacity and plastic modulus of the unsymme-
trical 'I' section, whose top flange size 100 mm x 15 mm bottom-flange size
200 mm x 15 mm and web size is 200 mm x 15 mm. 5
(c) A column ISWB 300@471·8 N/m is to carry an axial factored load of600 kN.
M20 concrete is used for the foundation. Design the slab base. Provide welded
connection between column and base plate. Given that the column end and the
base plate are not machined for bearing, . 7

5. (a) Why base plate is required below the column? 2

'(b) Determine safe axial load on a circular column of200 mm diameter made up
of deodar (HP) wood. Unsupported length of the column is l·5 m being situated
in outside location. 5
(c) A sal wood beam of standard grade carrying an all inclusive load 0(20 KNIM
is simply supported over masonry walls at both the ends, Design the beam for;
flexure, shear and bearing. Given that clear span = 4 m and inside location. 7

6. (a) What-do you mean by decay in timber? , 2

(b) A tubular column consists ofIS-1161 grade st. 35 steel the column is hinged at
both the ends. The outside diameter of tube is 219·1 mm. The weight of 1·5 m
length of the tube is 330 N. The length 0 co umn IS me er. e e n
safe load carrying capacity of the column. 5
(c) Design ground floor wall for a double storey building of the following specifi-
cation only considering one room of size 6 m x 4.m with suitable doors and
windows. .:;' ;.
(i) Wall thickness = 230 mm
(ii) Clear height of walls in each floor = 3·00 mm. .
(iii) Floor consists of 125 mm thick R~c slab with 25 mm thick patent stone.
(iv) Roof consists of 125 mm thick R.C.C. slab with. 125 mm line concrete over it.
(v) Live loads on floor and roof shall be 3 KN/m2 and 1·5 KN/m2 respectively. 7

·7. (a) Define non-load bearing walls and explain by taking different-types of non-load
bearing walls. 2
(b) Design a solid circular deodar wood column for the following datas axial load
on the column = 700 KN and effective length = 4 m (inside location). 5
(c) Design a column section (using channel section only) to carry a factored axial
load of 500 KN. The column is 4 m long and is effectively held in position at
both ends but. restrained against rotation at• one end only. Consider fy = 250
Nrmm'. Assume wind and earthquake action. 7

VI - Sem/CIVILI20 19(5)(NewXCET-602) VT-l,620

o Total Pages- 4 VI - SemI CIVIL/2019(S)(New)

ESTIMATING AND COST EVALUATION - II

(Code: CET-604)
Full Marks : 70 Time: 3 hours
Answer any five questions including Q.No.6 .
Figures in the right-hand margin indicate marks

1. The dimension of a R.C.C slab is 4.00 m x 5.00 m x 15cm deep. Reinforcement of

10 mm dia are placed in short span@15cm c/c. Of the total no of bars, 17 nos have
been cranked and hooked at the ends. Other rods are straight and hooked at the ends.
To hold the cranked portion 4 nos 8 mm dia straight and hooked rods have been used.
The 8 mm dia rods are placed in a direction of long span @20 em c/c and all are
straight and hooked at the ends. The covers are 1.5 c.m at bottom and 3 c.m. on all
.sides. Assume any other dimension not given. Estimate the total weight of steel
required for reinforcement of the slab. 14

2. Calculate the quantity of earthwork for a portion of road from the following data:
Chainage '50 . 51 52 53 54 55 56 57 58 59 60
Ground 131.9 .132.2 131.8 131.7 131.6 131.4 130.1 130.5 130.7
level(R:L) 132.1 132.2

The formation level at the chainage 50 is 131.0 m and the road is in a rising gradient
of 1 in 200. The width of formation is 10 m and the side slopes are 1.5 : 1 in banking
and 2 : 1 in cutting and the lateral slopes of the road is assumed as level. The length
of one chain is 20 m. 14

3. Estimate the items involved for the construction of a new state highway of WBM
road from the following data: 14
i .Length of road = 2 Km, Formation width = 12 m, Metalled width = 8 m,
Width of permanent land = 35 m, Depth of borrow pit = 30 em,
Average height of bank = 1.5 m(side slope = 2 : 1),
Thickness of grade - I metal soling = 90 mm
Wearing coat of grade - II metal = 12 em loose and compacted to 8 cm.
Surface to be finished with 2 coats of bitumen as given below.
First finishing coat = 12 mm chips @.025 m? and bitumen @1.25 kg per m2 of
road surface.
Second finishing coat = 6 mm chips @0.020 m! and bitumen @1.24 kg per m2
of road surface. Consumption of fuel @0.45 kg per kg of bitumen.

4.. Prepare a quantity estimate for the following items of works ofthe slab culvert given
in figure 1.
(a) Earthwork in excavation. 4
(b) Cement concrete in foundation. 2

(Turn Over)
,
 ( 2 )

(c) 1st class brick work in cement mortar. 4

(d) Cement plastering over brickwork in cement mortar. 4
I
']

.•Rotd Ltytl 0.

r---if----i ~20 S
Road
~

I 20 :
rA---- - - - - - - - - - - .J, - --
Ia.. . _ --
•••

. , t-150 .....j
j
SlCTIOR OR ABCD
I
II
I
I

§
•..
-
~
...

tA. . ~150~~ 365 ---.J

HALF FOUImATIOII PUI w.,j R!LF PLAII ABOVE G.L.

ALL DIMENSIONS IN CENTIMETRE

Figure - 1

5. Prepare a quantity estimate for the following items of works of a drainage siphon
given in figure 2 and 3.
(a) Earthwork in excavation. 4
(b) Cement concrete in foundation. 2

VI-Sem/CIVllJ201 9(S)(New)(CET-604) (Continued)

 <:
T
.-.-
I
•...
o
10
G,l.
~~
n .....
S ...•.
G

G
::s ~VI
••••.
"tj
_ VI
0-
VI

~<1>
,g ~
VI
""1
••••
•..•.
0
~ :;0;-
Q S' ~
~
~
'-'
' .. (JQ
o
<:
G
0
""1
:;0;-
_.
""1 ::s
0-0
""1 G
a'S
:;o;-G
'I" ~a
t-rj
1f-110-tt .•••.
g:;0;-0S
.-
~'

,
a '
t' f '15 l' •.•-::4-
::s ~ w

"'R
,co I'T
G
, .LL 30, 120 ,Sectronal Plan ,'I'
'I '
o
G
~

h::
,",11 "-"
tv 1 ' S
I- - - 1t--210 70; Showing all Footings G
::s
...•.
f .' [.-70,
..-----:- ...-- .. ~
~'l',~~~/,,,"·'
'. 30' ," "" , ' " - -
~:, - -
.
' , .
i:f 30
. :~! ,-
•
',' ~ "','.
:f,o\
"
:11' • , •
J S
o
::4-
~80CmBedOfNala
_. 270 , : :.,1
• ,I,' ' , !. I ,, I
~

III
1
.. (.
.--4§:'
'30
~op
D
180x180,
p't'
II
,
'I.
"
't
150
I,
I'

"
",'

It • Drop Pit
,I ,
I ~
• :z:::a:
o cm Ory Brick Pitching ~30' ~_ ••.- ••.••. - - 1.-1- --_. - - .;, ""'" 180x180
"'-1-- ----- ---- -'"' -""--. ----""
L_' ~ ••••• I
r- ~. ,.
I. _ ••• --
,
-
II I 1 I
----"'1"'I -,
(
,
r"
1SI ope,
1'1:a'
~,
------- ,J . 30•••••• . ,I.,
--1'
,
'lil4q:l::125
,I"
'I.
•••
15__ ••••

~150E, ~ 150
~',- _ ••••--

'
.• ----

150.,
"
l:l::;
"
,I I s;::r
.J:z:a::

4J
'
' J 20
'.30"',1
f :-_
~ il'': ' 15
.....!1
•.

8.
~
~
1.2· Bed of. Q) E Q)
,I"
I
tl'
u' J•
I~
.~

1 1 .... ~
,-.., Bank of Nala CD.8, Minor ~ ~ ~ L.: ~_I

:?
~
J W o
••

..
,
-..:....
Bank g
(1) (1)\ ' ,
...•...
(j)

--
(j) Bank

~
.,.
AllDimensions in centimetre
~ - -- •• c{
-:;..
,(\)

Top Plan. •... •...

 (4 )

·ORAlNAGE SYPHON
Cross Sections
G L
: • ,.I

G L

""--2o(Q JI
. II, 270 '
".~~ Sec1Ion·CD Showing Drop Pit and.Nala
. .~tO
~30

G -P-
15cmA.C.C.Sab 1f

Figure - 3

6. Write short notes on : 1

3-x4
(i) Administrative Approval and technical Sanction 2
(ii) Earnest money Deposit and Security Deposit
(iii)Muster Roll
(iv) Measurement Book.

,
VI-Sem/CMU20I 9(S)(NewXCET-604)
vr-9,OOO

--~-~--------~-----------------------------
 VI- SEM CIVIL / 2019(W)
CET 601 CONSTRUCTION MANAGEMENT
Full Marks: 80 Time : 3 Hours
Answer Any five Questions including Q.No. 1 & 2.
Figures in the right hand margin indicates marks

1. Answer all questions. 2x10

(a) What do you mean by work study .
(b) Define earliest event time .
(c) Write two limitations of bar chart.
(d) Define pessimistic time.
(e) What do you mean by quality control.
(f) Write any 5 functions of costruction management.

5
(g) What are the construction team components.
(h) Define material schedule.
(i) What do you mean by bar chart .

30
(j) What do you mean by piece rate or piece work system.

Answer any six Questions.

2. 5x6
(a) What are the characteristics of labour and explain it.
(b) Describe the causes of accidents in costruction.
61
(c) Describe about the resources of construction management.
(d) Describe the stages of construction planning.
(e) What are the advantages and disadvantages of line and staff organization.
(f) What are the type of motivation used in labour management.
12
(g) What are the maintenances used in equipments of construction.
3.
Describe the Safety measures required for demolition, fabrication and erection. 10
4. The following information applies to a particular project. 10
1

Event A is the initial event.

Event B is preceded by event A.
Event D is preceded by event B.
00

Event E is preceded by event D.

Event C is preceded by event B.
Event D is preceded by events C and B.
Event E is preceded by events D and B.
Event F is preceded by event E.
01

The expected time for various activities is as follows.

Activity A-B B-D B-C C-D B-E D-E E-F
Duration 3 16 6 8 10 5 3
(i) Draw the network diagram of the project .
(ii) Calculate the critical path.

5. What do you mean by construction management and describe the factors affecting the construction
management. 10
6. What are the conflicts in organization ? Discuss the genesis of conflicts and types of conflicts.
7. Explain the importance of leadership and human relations in managing a construction project. 10
10

VI- SEM CIVIL(Regular) / CET 601

 VI- SEM/CIVIL/2019(W)
CET-602-STRUCTURAL DESIGN-II
Full Marks: 80 Time: 3 Hours
Answer any Five Questions including Q No. 1& 2
Figures in the right hand margin indicates marks
1. Answer ALL the questions. 2X10
(a) Write down the different types of steel structures.
(b) Define hardness.
(c) Define pitch of the bolt.
(d) Write down the types of welded joints.
(e) Define slenderness ratio.
(f) A steel plate 25 cm wide & 12 cm thick, if the diameter of the bolt hole is 20mm, calculate
net sectional area of the plate.

2
(g) What is the maximum deflection in the beam as per IS:800?
(h) What is the function of column base?
(i) What are knots in timber?

25
(j) Define Buttress walls.
Q.2 Answer any SIX questions. 5X6
(a) Write down advantages and disadvantages of steel structure.
(b) A tie member consists of 2 ISMC 250. The channels are connected on either side of a 12 mm
thick gusset plate. Design the welded joint to develop the full strength of the tie. However the
overlap is to be limited to 400 mm.
81
(c) Explain different modes of failure of tension member.
(d) Determine the axial load capacity of the column ISHB 300 @ 577 N/m if the length of
column is 3m & it’s both end pinned.
(e) Design a slab base for a column ISHB 300 @ 577 N/m carrying an axial factor load of 1000
KN. M20 concrete is used for the foundation. Provide welded connection between column &
12
base plate.
(f) Determine the load carrying capacity of a strut made with 2 ISA 75× 75, 6mm, back to back
if the length member is 3m & welded to a 12 mm gusset plate.
(g) Discuss about long term deformation in timber.
1

Q.3 Design a single bolted double cover butt joint to connect boiler plates of thickness 12 mm for 10
maximum efficiency. Use M16 bolts of grade 4.6. Boiler plates are Fe 410 grade. Find the efficiency
of the joint.
00

Q.4 A column 4m long has to support a factored load of 6000 KN. The column is effectively held at both 10
ends & restrained in direction at one of the ends. Design the column using beam section and plates.

Q.5 Design a simply supported beam of effective span 1.5 m carrying a factored load concentrated load of 10
01

360 KN at mid span.

Q.6 Calculate the moment carrying capacity of laterally unstrained beam mode of ISMB 400 & length of 10
member is equal to 4m. Assume necessary suitable data.

Q.7 Write short notes on

(a) Web crippling & web buckling
(b) Block shear. 5x2
 VI- SEM/CIVIL/2019(W)/(NEW)
CET-603-RAILWAY AND BRIDGE ENGINEERING
Full Marks: 80 Time : 3 Hours
Answer any Five Questions including Q No. 1& 2
Figures in the right hand margin indicates marks

1. Answer ALL the questions: 2X10

a Write two advantages of railway.
b Write the term used for distance between running faces of rails.
c Define sleeper.
d Define turnouts.

0
e What do you mean by bridge?
f What do you mean by skew bridge?

30
g Differentiate between square alignment and skew alignment.
h What is a cofferdam?
i What do you mean by load carrying capacity of piles?
j What is an approach road for a bridge?
01
2. Answer any SIX questions: 5X6
a Describe the various factors which affect the length of rail.
13

b If the rulling gradient is 1 in 150 on a particular section of Board Gauge and at the same time a curve
of 4 degree is situated on this rulling gradient, what would be the allowable rulling gradient?
c Explain crossings and various parts of crossings.
1

d Explain points of switches.

e What do you mean by Afflux and explain Marriman’s formula?
00

f Explain the ideal bridge site characteristics?

g Differentiate between pipe culvert and box culvert?

3. What are the factors governing the selection of Gauge? Explain in details. 10
01

4. Write down about the various classifications of sleepers. 10

5. Describe in details the requirements of an ideal permanent way. 10

6. Explain the maintenance of track and advantages of good maintenance. 10

7. What do you mean by pile driving? Describe the various hammers used in pile driving? 10
 VI- SEM CIVIL/2019(W)/ (New)
CET 604 -ESTIMATION & COST EVALUATION-II
Full Marks: 80 Time : 3 Hours
Answer any FIVE Questions including Q No. 6
Figures in the right hand margin indicates marks
1. Calculate the quantity of earthwork for a portion of a road under construction from the following data: 15
R.D. 1500.0 1530.0 1560.0 1590.0 1620.0 1680.0 1710.0 1740.0 1770.0 1800.0
N.S.L. 141.2 141.3 141.0 141.3 140.9 140.7 140.5 139.2 139.6 139.8
Formation 140.1 -----------------------Rising gradient of 1 in 200------------------------------
Level
The width of formation is 10 m and the side slopes are 2:1 in cutting and width of formation is 8 m and
the side slopes are 1.5:1 in banking.
2. Estimate the quantities of different items involved for the construction of a new WBM road from the
following data: 15

3
Length of the road = 6 Km, Formation width = 10 m, Metalled width = 8 m,
Thickness of grade-I metal soling = 100 mm
Wearing coat of grade-II metal = 120 mm loose compacted to 80 mm

24
Surface finishing is as follows:
1st coat of finishing = 12 mm chips @ 0.020 m3 and bitumen @ 1.20 Kg per m2 of road surface.
2nd coat of finishing = 6 mm chips @ 0.018 m3 and bitumen @ 1.25 Kg per m2 of road surface.
Fuel consumption = @ 0.50 Kg per Kg of bitumen.
3. Estimate the quantities of the following items of works of a canal fall given in figure-I
(a) Earthwork in Excavation in hard soil
(b) Stone Masonry work in C.M. (1:4)
31 5
5
(c) Pointing work in C.M. (1:6) 5
4. Estimate the quantities of the following items of works of a slab culvert given in figure-II
(a) Earth work in Excavation in hard soil 5
(b) Cement concrete in foundation in C.C. (1:3:6) 3
20

(c) 1st Class Brick masonry work in C.M. (1:6) up to slab 7

5. A room has a clear dimension of 3 m X 7 m. It has a RCC slab as shown in figure below. Estimate the
quantities of following items.
1
00
01

(a) Cement concrete (1:1.5:3) 2

(b) Centering & Shuttering 2
(c) Weight of 6 mm & 12 mm dia bars including 10% wastage 8
(d) Prepare a bar bending schedule 3
6. Answer any FOUR questions
(a) Write down about classification of works briefly 4x5
(b) Differentiate between Muster Roll & Acquittance Roll
(c) Write down a Notice inviting Tender for construction of a new bridge over a river
(d) Describe about procedure for verification of stock
(e) Write down the various payment process to a contractor adopted by department

1/3
 3
24
31
20
1
00
01

Figure -I
2/3
 3
24
31
1 20
00
01

VI SEM CIVIL CET 604 3/3

 VI- SEM CIVIL / 2019(W) / (New)
CET 605 – E(iii) ADVANCE CONSTRUCTION TECHNIQES AND EQUIPMENTS

Full Marks: 80 Time : 3 Hours

Answer any FIVE Questions including Q No. 1 & 2
Figures in the right hand margin indicates marks
1. Answer ALL questions 2x10
(a) What do you mean by curing of concrete?
(b) What do you mean by target strength in concrete mix-design?
(c) Define workability of concrete.
(d) What do you mean by reinforcing?
(e) What do you mean by fibres?
(f) What do you mean by Earthquakes?

7
(g) Define retrofitting of structures.
(h) How the intensity of light is measured?
(i) What do you mean by building configuration?

25
(j) What are the functions of bulldozers and dragline?

2. Answer any SIX questions. 5x6

(a) What are the different properties and uses of artificial timber ?
(b) What are the systems and problems on ventilation? Describe with sketches.
51
(c) Write the advantages and disadvantages of prefabrication.
(d) What are the electrical service requirements in high rise building?
(e) What are the sources of weakness in RCC framed building?
(f) State different plan configuration problem.
(g) Describe briefly how plastics are used in construction of structures.
20

3. Classify retrofitting techniques and describe their uses. 10

4. Describe different earth moving and compacting equipments indicating their specific use with 10
suitable sketches.
1

5. Discus about the building characteristics in earthquake resistance construction. 10

00

6. What do you mean by earthing? Describe the process and advantages of earthing. 10

7. Write short notes on.

(a) Micro silica 2.5x4
(b) Soil Reinforcing
(c) Acoustic material
01

(d) Geo-synthesis
 . , . ,,<
I'. .....
:"'VI~·s~mJ.ME~():19(S)(N~) .
r .•• -.

Total Paies -2 . ~ - ~ -', •. <'

,'''., .'..... . -." '"". ';,,:

INDUSTRiALENGG AND QUALITY CONTROL " .

(Code: MET-601)
Full Marks: 70 ~.: Time: 3 hours
.'

, ' Answer any five questions '" '

Figures in~:iheright-ha~d 'margin indicate' ma~k8.· ,..-. , \ '.
?1. (a) What are the. objectives of plant layout?
,
2
(b): Give symptoms of bad layout, 5
(c) Describe the features of governing plant location: 7

2. ' (0) pef41e OperationR~s~eai:c~;:.', ...•.

(b) Gi~e a comparisonbetween PERr and CPM.
(c) Maximize Z = 12x + 24y
' ..
subject to x + '4y' S 20
3x+ Y S 15
x +y S 6 , ;:,~~,~~~~~.r-ff.:cp;
x,y::::-o _"'1..:~

use graphical method. 7

3. (a) Define ~ventory. 2

. (b) ExplainABC·analysiS. 5
(c) Calculate EOQ, given that
Annual usage =riOC)'wiiis':':' ::. :.~>~.:..• ."
•i • • • ••••
.
'; .:

,
. .~ ". :.

.' ."
Procurement cost = Rs. 25/order .
.:.
. t , ';

Cost per 10 pieces = Rs. 1000

Cost of carrying Inventory = 15% . '7

.- 4. (a) W1lat is Prime Cost? 2

(b) State Advantages and disadvantages of Master ScheduIiDg.' .,:. 5
t '-~'. ~.. .•.. ',' ,"

(c) . What is preventive maintainance ? Write its objectives: . 7

5. (a) What is TQ¥ ? 2

• .(b) What are the factors which affect the quality of manufacture? 5
(c) Draw the critical path and Final project duration of the following table':
..... . ".:
' ..
.,

(Thrn Over)

---
 ..
. ' - .. . .' ~,:'" . .. .' ,
., , .. ,.

"
(2 )

Activity .Time in days

(1-2)P . 09
. (2-3)Q ::" ::i .. ' '-.' 14
(34)R'·:'; .'~~. >-··~':·>'i8··· " .'/'

{~-5)S 12
(4-6)1' 15
(5-6)U 03
(6-7)V. '02 7

6. (a) ·Whatis Time Study-?<·, ; ':._". .' . .v: .. 2

(b) What are the characteristics ofISO-9000? .. -t 5
(e) What are the different types of control chart 1Explain X ch~ and P-:ehart. 7

7. (a) Whatis JITTechnique? 2·

(b) Describe different typeS of over heads. 5
(e) - Exp1aindifferenttYPes~fInspeciion.": - 7

:., " .
" -

'. .'~... :: .. .' '.~.

'-.,
.. ""

..
'. ", •• 7. '. •• ," .. ' .•

\ " ~ 1 ".

.-Vl-ScmlldEC~019(S)(Ncw)(MET-601) . VT-IP20

.-- ...
 VI-SemIMECBIlOl9(S)(New) ,
::
',l

AlITOMOB~E ENGG '

'. (Code: MET-602)
'-
Full Marks : 70 Time: 3 hours
Answer any five questions
Figures in the right-hand margin indicate marks

1. (a) What is self-propelled vehicle? 2

(b) Write down the technical specifications ofMaruti-800. 5
(c) Explain'in detail about sliding mesh gearbox. 7

2. (a) Name the different types of differentials. 2

(b) Name two numbers of friction lining materials. What are the properties of a r,

good clutch lining? 5

(c) Explain about torque tube type propeller shaft. 7

3. (a) According to method of braking contact, name the different types of brakes. 2
(b) Write-down the advantages of hydraulic brakes. 5
(c) Explain about air brake with figure. 7

4. (a) What is the function of spark plug ? 2

(b) Explain about flashing indicators? 5
(c) Explain about causes and remedies oftyre wear .. 7
.'

S. (a) Define flange and gutter for tyre. 2

,(b) Explain about tubeless tyre. S
(c) Explain about cooling defets and their remedial measures. 7

6. (a) -Define flash point and rue point. 2

(b) Why cooling is provided in I.C. engines? 5
(c) Explain about drysump lubrication system. 7

7. (a) Name the factors which influence the process of carburetion. 2

(b) Write down the functions of fuel injection system. S
(c) Explain about diesel fuel filter.' '7

VT-2,SOO
 'I
I
VI-Sem/MECHl2019(S)(New)

ADVANCEDMANUFACTURINGANDCAD/CAM
(Code: MET-603)
Full Marks: 70 Time: 3 hours I
I

Answer any five questions

Figures in the right-hand margin indicate marks

1. (a) Classify the non-traditional machining processes. 2

(b) What are the advantages and disadvantages ofEDM ? S
(c) Briefly describe the principle of Electro-discharge machining. 7
'...
2. (a) What are the materials commonly used for making a tool in ECM ? 2
(b) List advantages, disadvantages ~d application ofECM. S
(c) Explain how Electron-beam machining is carried out. 7

3. (a) 'List the common abrasive powders used inAJM. 2

(b) What is LASER? Differentiate LBM and EBM. S
(c) Explain the principle of plasma arc machining with neat sketch. 7
01. 2
(b) What are the important components of a NC systems? Describe in brief. S
(c) Differentiate between NC, CNC and DNC system. 7

5. (a) Define 'Robot'. 2

(b) Explain industrial application of robot. S
(c) Describe the important configuration of industrial robot with neat sketch. 'I
7
I
6. (a) Define automation. Write down the advantage's of automation. 2
(b) Explain different types of automation. S
(c) What are the tool positioning modes in NC programming? Explain them with
neat sketch. 7
7. (a) Define FMS. 2
(b) List advantages and disadvantages ofFMS. S
(c) Identify different components ofFMS. Explain them in brief. 7

Vf-4,620
 VI- SEM COMMON/2019(W)/ (New)
BST - 501-ENVIRONMENTAL STUDIES (COMMON)
Full Marks: 80 Time : 3 Hours
Answer any Five Questions including Q No. 1& 2
Figures in the right hand margin indicates marks

Q1. Answer all the questions. [2x10]

(a) What is photochemical smog?
(b) Define ecosystem.
(c) What is captive breeding?

5
(d) What do you mean by biocides?
(e) What is a wasteland?

30
(f) Define Emigration.
(g) What is hydrosphere?
(h) What is food web?
(i) Define alpha diversity.
61
(j) What is mixed cropping?

Q2. Answer any six questions from the following. [5 x 6]

12

(i) Discuss in brief ‘Ecological pyramid’.

(ii) Write a short note on ‘acid rain’.
1

(iii) Describe the effects of mining practices on tribal people and on the environment.
(iv) Explain how ‘Environmental studies’ is multidisciplinary in nature.
00

(v) How wild life was conserved in ancient India?

(vi) Write a short note on global warming.
(vii) Discuss the factors which affect population distribution?
01

Q3. What is noise? What are the major causes of noise pollution? How can it be prevented? [2+4+4]
Q4. Discuss different methods adopted for conservation of biodiversity. [10]
Q5. Describe different components and functions of forest ecosystem. [10]
Q6. Discuss different methods and advances of rain water harvesting. [10]
Q7. Discuss the effects of construction of dams on tribal people and on the environment. [10]

III- SEM ELECTRICAL/ETC/AEI&E (New)

 VI- SEM DIP.MECH/MECHANICAL ENGG/2019(W)
MET-601-INDUSTRIAL ENGG & QUALITY CONTROL
Full Marks: 80 Time : 3 Hours
Answer any Five Questions including Q No. 1 & 2
Figures in the right hand margin indicates marks
USE OF CALCULATOR IS ALLOWED
1. Answer ALL the questions in brief: 2X10
(a) What is an ideal plant location?
(b) What are the different types of plant layout?
(c) Define operation research.
(d) What do you mean by optimistic time?

2
(e) What do you mean by Economic order quantity?

25
(f) Write two objectives of maintenance.
(g) Define inspection.
(h) What is statistical quality control?
(i) Define TQM.
(j) What is JIT-technique?
81
2. Answer any SIX questions from the following questions: 5X6
(a) What are the objectives of good plant lay-out.
(b) Write comparison between PERT and CPM.
12

(c) What are the objectives of inventory control?

(d) Briefly explain preventive maintenance.
(e) Write briefly about the factors that influence quality of manufacturing.
1

(f) Briefly explain ISO 9000.

(g) What do you mean by control chart and briefly explain why it is used?
00

3. Describe the factors governing plant location. 10

01

4. A small projects require activities namely A-B, A-F, B-C, B-D, C-E, D-E, F-G, E-H, G-H with 10
activity completion time as 7, 6, 13, 5, 12, 7, 10, 4, 14 days respectively. Calculate EST, LST. Find
the total project duration and mark the critical path.

5. (a) What are the different basic inventory models? 3

(b) The rate of use of a raw material is 30000 units per year. The cost of placing & receiving an order is 7
Rs.70/-. The cost of each unit is Rs.2/-. The inventory carrying cost is 12% of the unit value per year.
Calculate EOQ.

(Turn over) 1/2

6. Explain the duties, functions and responsibilities of plant maintenance department. 10
7. (a) What are the different types of inspection? 3
(b) Calculate UCL and LCL for -Chart and R-chart of the following data. Take A2=0.58, D3=0, D4=2.11 7
Sample No R
1 21 5
2 23 4
3 25 5
4 26 6
5 24 4
6 23 4
7 29 6
8 25 4
9 28 4
10 30 3

2
25
81
1 12
00
01

2/2
 VI- SEM/MECH/DIP.MECH/2019(W)/(New)
MET-602-AUTOMOBILE ENGINEERING
Full Marks: 80 Time: 3 Hours
Answer any Five Questions including Q No. 1 & 2
Figures in the right hand margin indicates marks

1 Answer ALL the questions: 2X10

(i) Define automobile and give one example of it.
(ii) What is the purpose of using propeller shaft?
(iii) What is the aim of differential in automobiles?
(iv) Why air brake is so named?

0
(v) For what purpose spark plug is used?
(vi) Why we use flasher circuit?

30
(vii) What is the use of coil spring?
(viii) Why engine lubrication is needed?
(ix) Define Carburetion and Air Fuel Ratio.
(x) What is the use of fuel filter?
01
2 Answer any SIX questions: 5X6
(i) Write down the technical specifications of Indica (petrol).
13

(ii) Explain in brief about the working of single plate clutch with sketch.
(iii) Write a short note about vacuum brake.
(iv) Write briefly about common ignition system troubles and the remedies for prevention.
1

(v) Describe in short about telescopic shock absorber with sketch.

(vi) Write about the necessity of engine cooling.
00

(vii) Explain in short about common rail system for C.I. engines.

(3) Explain in detail the constant mesh gear box with clear diagram. 10
01

(4) Describe the drum brake and disc brake with proper diagrams. 10

(5) Write in detail about the tyre wear causes and the remedies. 10

(6) Explain the pressure lubrication system with figure. 10

(7) What is the magneto ignition system? Explain with neat sketch. 10
 VI- SEM /MECHANICAL/DIP.MECH/2019(W)/ (New)
MET-603-ADVANCED MANUFACTURING AND CAD/CAM.
Full Marks: 80 Time : 3 Hours
Answer any FIVE Questions including Q No. 1& 2
Figures in the right hand margin indicates marks
1. Answer ALL the question. [2x10]
a) What is EDM?
b) Define a Robot?
c) What is NC system?
d) Define work zero?
e) What is the use of sensors?

3
f) What is adaptive control?
g) What is CIM?

24
h) What is DNC?
i) Define Electro-chemical machining?
j) What is the circuit voltage and spark gap in EDM?
2. Answer any SIX questions
31 [5x6]
a)
Explain the working of ultrasonic machining process?
b)
State the objectives of using an industrial robot?
c)
Explain various components of NC system?
20
d)
List type of automation?
e)
State the benefits of CAD and CAM?
f)
Discuss various types of end effectors?
g)
1

Write short notes on: Economics of NC system?

3.
Explain with a neat sketch the working principle of Electron beam machining. State four
[10]
00

application?
4. Make neat sketch of a robot and show its main parts on it. [10]
5. Describe various types of NC Co-ordinate and explain point to point and straight cut NC co-ordinate [10]
system.
01

6. Explain preparatory function and G code along with miscellaneous function and M code. [10]
7. Explain different components of FMS. [10]
.
 VI- SEM MECHANICAL/E&M/DME/2019(W)
EMT-604/MET–604 E-(i) POWER PLANT ENGINEERING
Full Marks: 80 Time: 3 Hours
Answer any FIVE Questions including Q No. 1& 2
Figures in the right hand margin indicates marks
Steam table is permissible. Standard properties of air Cp, air= 1.005kJ/kgK, Cv,air= 0.718 kJ/kgK

1 Answer ALL questions. 2×10

(a) On which factor of index it is decided a country is developing or developed.

7
(b) What are different sources of energy?

(c) Write down two examples of Boiler mountings.

25
(d) Distinguish between central and captive power station.

(e) Recognize importance of draught (draft) system in boiler furnace.

51
(f) Applying knowledge of steam power plant define work ratio and back work ratio.

(g) State importance of condenser in steam power plant.

(h) What is a hot well related to steam power plant?

20

(i) Carbon atom has nuclear symbol . What is the atomic number and mass number for carbon atom?

(j) Define catchment area related to Hydro electric power plant.

1

2 Answer any SIX questions :

5×6
00

(a) What are renewable and non renewable sources of energy?

(b) Draw block diagram and T-s (Temperature- entropy plot) for Reheat regenerative Rankine cycle. One
Open fed water heater (OFWH) is used in low pressure side of steam turbine.
01

(c) Distinguish difference between boiler mountings and boiler accessories.

(d) Draw pressure and velocity profile for a 3 stage Pressure compounded steam turbine.

(e) Explain function of water level indicator and fusible plug used in boiler.

(f) Explain nuclear fission reaction.

(Turn over) 1/2

(g) Draw general layout of a hydro electric power plant.

3 Steam at 50 bar and 5000C expands in a simple rankine cycle to 1bar pressure. The mass flow rate in 10
steam power plant is 120 kg/sec. Determine
(i) Power developed by plant
(ii) Thermal efficiency of plant

4 Velocity of steam entering a simple impulse turbine is 1000 m/sec and nozzle angle is 200. The mean 10
peripheral velocity of blade is 400 m/sec. Blades are symmetrical. Steam enters to turbine without
shock. Mass flow rate of steam is 0.75 kg/sec. Determine
(i) Blade angle at inlet and exit
(ii) Tangential force on blades
(iii) Power developed by steam turbine

7
5 What is the function of a cooling tower in steam power plant, describe natural draft and mechanical 10
draft cooling tower.

25
6 Describe working principle of a nuclear reactor with all components explained. 10

7 Explain different systems of diesel power plant. 10

51
1 20
00
01

2/2
 6TH SEM./EME/ ELECTRICAL / 2022(S)

TH1 ELECTRICAL INSTALLATION AND ESTIMATING

Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

08
a. Name any two types of methods of earthing.
b. Write any two important properties of ACSR conductors used in transmission lines.
c. State the Rule 31 of Cut-out premises in general safety precautions of Indian Electricity
Rules.

09
d. How Britannia straight joint is made between two bare wires?
e. State any two accessories of conduit wiring system.
f. Define (i) Depreciation factor (ii) Luminous flux in illumination.
26
g. Name the material of filament and gas used in halogen lamp.
h. Expand the abbreviation of ACSR, TPIC, TRS, and MCCB used in electrical estimation.
i. What is the declared voltage and frequency of supply to consumer as per IE rules?
07

j. Define(i)Black conduit (ii) Bird Guards

2. Answer Any Six Questions 6x5

08

a. Explain about the installation of service line for low roof or single storeyed building
briefly.
b. Draw a neat labelled sketch diagram of plate earthing.
c. Explain the construction and working of RCCB briefly.
01

d. Explain about the High Pressure Mercury discharge lamp briefly with a neat diagram.
e. Describe the qualities and applications of PVC insulated wires.
f. Write a short note on Steel towers used for supporting transmission lines.
g What are the differences between concealed conduit wiring and TRS wiring?
3 A room and a verandah, the plan of which is given below is required to be provided with 10
electrical wiring. Mark the location of energy meter, main switch and switch board and
electrical points suitably and draw the installation plan showing supply path to each
point and wiring diagram. Calculate the total length of wire required for wiring the room
and verandah in batten system of wiring. Assume: Total height of ceiling= 3.5 mts.
Height of HR from floor=3.0 mts, Height of SB from floor=1.5 mt. Location of energy
meter and main switch board =0.5 mt. inside verandah on room wall.
1
 08
Explain the sequences to be followed in carrying out the estimate of domestic electrical 10
installations (from drawing installation plan to preparing material table) in details.
4
5 Draw the electrical circuit and calculate the length of PVC Casing-Capping, phase & 10

09
neutral wire for the wiring used in a house, the plan of which is given below. Assume the
height of ceiling as 3.6 meters and one plug point is to be provided in each room.
26
07
08

6 In a city locality, an overhead distribution line of 400 volts, 3 phase, 50 cycles/sec is to be 10

erected along a straight route on steel tubular poles. The length of the line is 500 meters
and the line terminates at the end. Make a neat sketch of a tubular pole with 3-phase
wires, earth wire, neutral wire and street light conductor, shackle insulators, reel insulator,
01

cable box, stay wire etc. and estimate the quantity of material required for installing the
distribution line with full specification of each item. Size of ACSR conductors, for all types
of wires, is 6/1x2.11 (squirrel conductor), Weight of ACSR conductor=85kg/km, Earth wire
Galvanized steel is of 8 SWG, Weight of earth wire=10mts/kg, Line Sag=2%
7 There are four light/power sub circuits in an installation of a house wiring as follows: 10
No. 1 Sub-Circuit: Light points-2nos., Fans-2 nos., 5A Socket-4 nos.
No. 2 Sub-Circuit: Light points-5nos., Fans-2 nos., 5A Socket-2 nos.
No. 3 Sub-Circuit: Light points-2nos., Fans-3 nos., 5A Socket-3 nos.
No.4 Sub-Circuit: 15A Socket-1 no (1000W).
Assuming each fan is of 70W, each light is of 40W, each 5A socket is of 60W and supply
voltage is 230V.Calculate the Total load in amperes assuming unity power factor. Also
draw the single line diagram showing cut-out, energy meter, main switch board, and
main distribution board.
2
 6th Sem. /ELECT./EEE/ ELECT(I & C )/EME / 2022(S)
TH-2 Switchgear and Protective Devices
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

03
a. Define(i) TSM(ii) Symmetrical fault
b. State any two important faults that occur on an alternator.
c. What is the use of distance relay?

09
d. What are the factors on which RRRV (rate of rise of restriking
voltage) in circuit breaker depends?
e. What are the desirable characteristics of fuse element?
f. State any two advantages of static relay.
27
g. A fuse wire of circular cross-section has a radius of 0·8 mm. The
wire blows off at a current of 8A. Calculate the radius of the wire
that will blow off at a current of 1A.
07

h. What is the function of surge absorber?

i. Define(i) Short circuit kVA (ii) Recovery voltage
j. Write any two advantages of valve type lightning arrester.
08

2. Answer Any Six Questions 6x5

a. What steps to be taken for the maintenance of oil circuit
01

breakers?
b. Write a short note on High voltage fuses.
c. A 3-phase, 20 MVA, 10 kV alternator has internal reactance of 5%
and negligible resistance. Find the external reactance per phase to
be connected in series with the alternator so that steady current
on short-circuit does not exceed 8 times the full load current.
d. Explain the protection of switchgear against lightning using
overhead ground wires briefly.
e. Write a brief note on plain break oil circuit breaker with a neat
diagram.
 f. How time-graded protection of a radial feeder can be achieved
using definite time relays and inverse time relays?
g Describe about the Earth fault or Leakage protection of 3 phase
transformer.

3 Explain about the construction and operation of Buchholz relay in 10

transformer with neat diagram.

03
4 With the help of neat diagram, describe the construction, working 10
of Vacuum circuit breakers and also write its advantages.
5 Write a brief note on i) Horn-gap arrester ii) Percentage 10
differential relay.

09
6 Explain about the construction and operation of Induction type 10
Directional power relay with a neat diagram
7 Describe the differential protection of Alternators using Merz- 10
Price circulating scheme in details.
27
07
08
01
 6TH SEM./ ELECTRICAL/2022(S)
TH-3 Control System Engineering
Full Marks: 80 Time- 3 Hrs
Answer any FIVEQuestions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

a. What is signal flow graph?
b. Define phase margin. Is it positive or negative for stable feedback systems?

58
c. What do you mean by velocity error constant?
d. Define(i)Gain cross over frequency (ii) Resonant frequency, in frequency domain
analysis.
e. What is the time response to unit ramp input in first order system?
f. What is corner frequency in Bode plot?

08
g. Define (i) Impulsesignal (ii) Transfer function.
h. What are the open loop poles of G(s).H(s) = ?

i. What do you mean by all pass system?

j.
28
What are the advantages of polar plot?

2. Answer Any Six Questions 6x5

a. Explain the effects of feedback in a closed loop control system.
b. What are the basic properties of signal flow graph?
07

c. Derive the damped natural frequency from the time responseof second-order
system to the unit step signal.
d. Describe about the PI controller using Block Diagram briefly.
e. Write a brief note on Constant-M circles with the help of polar plot.
08

f. An unity feedback control system has an open loop transfer function:

G(s)= .Find the (i) Centroid of asymptotes(ii) Breakaway point.
g Explain the effect of addition of poles and zeros to G(S).H(S) on the shape of
Nyquist plot.
01

3 Explain all the rules for reduction of Block diagram, used in control systems in 10
details.
4 Explain about the Nicholas Chart used in frequency response analysis briefly. 10
5 Describe about the construction and working ofAC servomotors in details with 10
the help of a neat diagram.
6 Describe the properties, advantages, disadvantages of transfer function in details. 10
7 Derive the expression for rise time, peak time, peak overshoot for second order 10
systems
 6TH SEM./ ELECTRICAL/ELECT( I & C )/ 2022(S)
TH4 Testing & Maintenance of Electrical Machines

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x 10

48
a. What is circuit breaker?
b. State the provisions of fire protection of transformer.
c. How insulation resistance is checked?
d. Why starter is used in DC motor?

08
e. Write any two differences between indoor and outdoor substation.
f. What is an instrument transformer? Give an example.
g. Define maintenance? State its types.
h. What do you mean by BDV test of transformer oil?
29
i. Which starters are used to run 3-phase induction motors?
j. Why earthing of transformer tank and cover is required?

2. Answer Any Six Questions 6x5

07

a. What are the advantages of preventive maintenance?

b. What is breather? Explain charging process of a breather.
c. Explain about the civil construction feature for installation of a transformer.
d. Explain about the preventive maintenance schedule of SF6 Circuit breaker
08

used in substations briefly.

e. Describe the characteristics of oil used in transformers.
f. Write a short note on wiring of electric motors.
g Write a short note on Bus bar earthing connections along with the safety
01

precautions taken for it.

3 Describe the generalized procedure of installation of Electrical Machines. 10

4 Prepare a maintenance schedule of Transformer and Batteries in substation. 10

5 Explain briefly about installation of outdoor Circuit breaker. 10

6 How filling of oil and drying out process take place for a transformer? 10
7 With the help of a neat key diagram, explain the general requirements of 10
layout of indoor substation in details.
 III-SEM./ELECTRICAL/ETE/AE&IE/EME/ ELECTRICAL[PT]
/EEE/ELECTRICAL(INST & CTRL)/ECE/2021(W)
TH-I ENGINEERING MATHEMATICS -III

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

54
1. Answer All questions 2 x 10

a. What are homogeneous equations? State the condition to get

non-trivial solutions for homogeneous equations.

12
b. Find Particular Integral of ( ) .
c. Frame a differential equation for the function ( ).
d. Write the Existence Theorem of Laplace Transform.
02
e. Find { }.
f. Define Periodic function. Give one example of periodic function with
its period.
03

g. Write Newton Raphson Formula to find a root of equation

( )
h. Evaluate ( ).
i. State Trapezoidal Rule. Why this is called Trapezoidal Rule?
54

j. Express in the form of .

2. Answer Any Six Questions 5x6

01

a. Find the root of the equation correct to 3-places

of decimal by Newton Raphson Method.
b. Find the Laplace Transform of ( ) ( )
c. State Dirichlet’s condition for a function to be expanded in Fourier
Series. Find ( )
In
d. Evaluate ∫ using Trapezoidal Rule with 5 subintervals.
e. Find the Inverse Laplace Transform of
( )
( )( )
1
 f. Find ( ) when x=32 from the following data using Newton Forward
Interpolation Formula
x 30 35 40 45 50
f(x) 15.9 14.9 14.1 13.3 12.5
g Solve the following differential equation
( )

54
3 i) Express ( ) ( ) as a Fourier Series in the interval ( ) 7
Hence deduce the value of the series
ii) Find √ 3

12
4 i) Solve the following partial differential equation 6
( ) ( ) ( )

ii) Evaluate using Simpson’s Rule correct up to 3-places of 4

∫
02
decimal taking h=1.
5 i) Solve the differential equation 5
( )
03

ii) Find the Laplace Transform of ( ) 5

6 i) Find k if the following equations are consistent 5
X+2y-3z=-2
54

3x-y-2z=1
2x+3y-5z=k
ii) Find f(x) when x=15
x 3 7 11 19
5
01

F(x) 42 43 47 60
7 i) Solve the following differential equation 5
( )

ii) If is the cube root of unity, show that 5

( ) ( )

2
 3rd Sem. E&TC 2021(W)

Th-4 ELECTRONICS MEASUREMENT & INSTRUMENTATION

Full Marks: 80 Time- 3 Hrs

Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

05
a. What is Lissajous pattern?
b. Define the accuracy and sensitivity.
c. Write down the application of digital tachometer.

13
d. State the difference between transducer and sensor.
e. Define the static and dynamic characteristics.
f. State the advantages and disadvantages of MI instruments.
g. What is DSO?
h.
07
Define Q factor.
i. Draw the diagram of De-Sauty bridge.
j. What is signal generator and classify it?
2. Answer Any Six Questions 6x5
03

a. What is errors of an instrument and explain various types of errors?

b. Explain the basic principle of operation of AC voltmeter with its application.
c. A 1mA meter movement with an internal resistance of 100Ω is to be converted into a 0-
54

100mA. Calculate the value of shunt resistance required with proper circuit diagram.
d. Which bridge is used for measurement of unknown inductance? Explain the working of
that bridge.
e. Define transducer and explain the working of load cell.
f.
01

Draw the diagram of ramp type digital voltmeter and explain its operation.
g Explain the working of wave analyser.
3 Describe the construction and operation of PMMC instruments with its advantages and 10
disadvantages.
4 With neat diagram explain the construction and working of LVDT. 10
5 Draw the block diagram of CRO and describe the function of each block and write down 10
the application of CRO.
6 Describe the bridge used to measure the unknown resistance and write its applications. 10

7 Write the short note on: 10

1) Thermistor
2) Analog multimeter

1
 III-SEM/ETE/AE & IE/ECE/ 2021(W)
TH-II Circuit Theory
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks
1. Answer All questions 2 x10
a. Convert a 20V voltage source having internal resistance of 10 ohm into an equivalent
current source.

00
b. A 12V voltage source, 4Ω resistor and 6Ω resistor are connected in series.Find the
voltage drop at each resistor using voltage division rule.
c. State Maximum power transfer theorem.
d. Under which conditions superposition theorem is applicable?

13
e. Define Form Factor.
f. Find out the Time constant of a series RC circuit if R= 1KΩ, C=1mF.
g. Draw the resonance curve of Series RLC and Parallel RLC circuit.
h.
03
Represent a parallel RLC circuit of R=10 Ω, L=5H and C=100mF in Laplace
Domain.
i. Draw a simple resistive (a) T-network (b) Pi-network
j. Write down the voltage and current equations related to Z-parameters and Y-
parameters of a two port network.
03

2. Answer Any Six Questions 5X6

a. Find out the equivalent resistance between node ‘a’ and ‘b’.
54
01

b. Find loop currents I1 and I2 using mesh analysis in the below circuit.

c. Explain the step followed to solve a circuit using Norton’s theorem.

1
 d. In an AC Circuit, Derive the expression for current in pure capacitor. Draw the
phasor for Voltage and Current.
e. Determine the values of R, L, C of a parallel RLC circuit, If it’s resonant frequency is
10KHz and Quality factor is 20.
f. Find the z-parameters of the circuit given below.

00
g Determine the impulse response of series RC and RL circuit.

13
3 Determine the current flowing in Resistor RL. 10
03
03

4 Find the current in 5Ω resistor in the below shown circuit using Thevenin’s theorem. 10
54
01

5 A 50∠0o V ac supply of 50Hz frequency is applied to a Series RL circuit having 10

R=100 Ω, L=20mH. Determine current, power factor, active power, reactive power
and draw the power triangle.
6 Derive the expression for resonant frequency in a series RLC circuit. If R=2Ω, 10
L=1mH, C=4nF, Determine Resonance Frequency, Q-factor, Bandwidth and half
power frequencies.
7 Define and classify filters. Explain various types of filters with frequency response. 10

2
 3rd Sem. Common 2021(W)
Th-5 Environmental Studies
Full Marks: 80 Time- 3 Hrs
Answer any five Questions including Q No.1& 2
Figures in the right hand margin indicates marks

1. Answer All questions 2 x 10

52
a. Define acid rain.
b. What is ecological succession?
c. What do you mean by soil erosion?
d. Define genetics and species.

12
e. Mention any two causes of marine pollution.
f. Define environment.
g. What is mortality?
h.
08
What do you mean by sustainable development?
i. What leads to conflicts over water?
j. Define water pollution.
03

2. Answer Any Six Questions 6x5

a. Define and explain food chain with at least one example.
b. Explain the changes caused by modern agriculture.
c. Explain Biodiversity at National level.
54

d. Give a brief note on ozone layer depletion along with its consequences.
e. Discuss in brief ‘Human Rights’.
f. Discuss the needs of public awareness towards environment.
01

g Explain cyclone disaster management.

3 Explain the effects of mine extraction on environment and tribal people. 10

4 Explain different threats to biodiversity. 10
5 Describe forest ecosystem. 10
6 Write down the causes, effects and controlling measures of soil pollution. 10
7 a Urban problems related to energy. 5
b Family welfare program. 5