Scribd
Upload
6 views

S3D Interface Manual

Uploaded by

Pierre Olivier
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
6 views

S3D Interface Manual

Uploaded by

Pierre Olivier
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

User Manual for the Interface of S3D Version 3.

This user manual provides information about how to run the streamline simulator S3D in
the windows environment. For details about the input data file structure and other
information, please refer to the S3D User Guide in the ‘Help’ menu after installing the
software.

1. Installation:

Double click on Setup.exe.

It will guide you through all the steps to set up the software in your computer. It is
recommended that you install the program with a simple path name, for example,
C:/S3D.

2. After installation is complete:

1. From Start Æ Programs, click on S3D.


2. Once the program starts, the main screen appears as below (Figure 1)

Figure 1. Starting Screen


3. To create a new project, Click File Æ New Project. Supply the Project name
on the appearing dialog box. An automatic extension of .S3D will be associated
with the project name. Choose a proper location for the project anywhere in the
computer using the Browse button. If required (recommended), create a new
folder for the new project. Before executing the program, all relevant data files
MUST be in this folder.

See Figs. 2, 3 & 4 for sequence to create a new project.

Figure 2. Supply a Project Name.


Figure 3. Supply a Location for File Information

Figure 4. A New Project is Created.

4. Once location for the new project is specified, Click OK (Figure 4). A panel
with project information will appear (Figure 5). Click OK to close it.
Figure 5. Project Location Information Panel.

5. Once all data files are available, modify them as necessary from the Input Data
Option. (Figure 6)

Figure 6. Input Data Panel.

6. Once modifications are complete (modified files need to be saved), the project is ready
to be executed. For execution, Click RUN button (or the Speed Button with two
running men). A DOS window will appear indicating progress of the simulation.
(Figure 7). After successful completion of the execution, the DOS window will close
with a message ‘Successful Execution’.

Note :

a. If there is some mistake in the input datafile, the DOS window will close with
a message ‘Execution Failed’.

b. Whenever the program is prematurely terminated, a *.log file is created. It


explains the reason for the early termination. It is always a good idea to check
the log file regardless of whether the program was executed properly or not.
In the event of a successful execution, the log file will verify that.

Figure 7. Simulation is in Progress.

7. Now the user is ready to view the results. Followings are the major points to consider
while viewing the results:

a. By clicking plots we can select the Plots shown in Figure 8.

b. Some of the plots (Streamlines, Water Saturation and Time of Flight) can also
also visualized by Tecplot Ver 8.0 or above if it is installed in the computer.
These output files properly formatted for Tecplot are written into the project
location folder.

c. All the plots can be ‘copied’ and ‘pasted’ in Word or other documents for
reporting purposes.
Figure 8. Selection of Plots

Followings are some examples of screenshots for plots.

Figure 9. Examples of Line Plots (Water Cut, Oil rate & Recovery).
Figure 10. Examples of Pie Charts (Layer Sweep & Rate Allocation).

Figure 11. Examples of Contour Plots (Sw & Time of Flight).


8. For solving the computer exercises in the book, several example cases have been
supplied with this software. The user can choose File Æ Existing Projects and open
these examples (Figure 12). Also, if the user completes a project and wants to open it
at a later time, it should be opened using File Æ Existing Projects option. If the
results were not deleted from the folder, user can view them without making new
simulation runs.

Figure 12. Opening an Existing Project.

You might also like