CV 2023
CV 2023
YTOM
Registered Mechanical Engineer, PRC License no: 0083607
Address: Purok 22 Sambulawan Street, Brgy. Poblacion, Bayugan City, Agusan Del Sur, Philippines
Email Address: [email protected]
Mobile no: +639156013064
__________________________________________________________________________________________
A Mechanical Engineer with 7 years in Circulated Fluidized Bed Boiler Coal Fired Power Plant with
Reheat Regenerative Steam Power Plant, with experience in Pre-Commissioning, Commissioning, Operation,
Maintenance and Boiler-Turbine Start-up and its auxiliaries.
Technical Skills:
Pre-Commissioning and Commissioning (e.g Hydrostatic Test, Air Leak Test, Refractory Dry-out,
Boiler Boil Out, Steam Blowing and Wet and Dry Boiler Preservation.
Thermal Scanning, Vibration Test, Motor Solo and Load Test, Penetration Test
Ability to read and interpret Piping and Instrumentation Diagram, Distributed Control System, Logic
Control System and detailed understanding in engineering drawing.
Domestic air-conditioning unit servicing
Basic Machining
Basic AutoCAD 2018
Maximo IBM
MS Word, Excel and Power Point
__________________________________________________________________________________________
Work Experience:
San Miguel Consolidated Power Corporation-Safetech Power Services Corp.
2 X 150 MW Circulated Fluidized Bed Boiler (ALSTOM) Coal Fired Power Plant with Reheat Regenerative
Steam Turbine (MITSUBISHI-HITACHI)
Brgy. Culaman, Malita, Davao Occidental, Philippines
Responsible for the start-ups and shutdowns of boiler, turbine, generator and its auxiliaries, as well as
unit synchronization to the grid.
Record, monitor and evaluate operating system parameters such as temperatures, pressures, tank
levels and flow trend curves. Make necessary recommendations to the Shift Supervisor for optimum
boiler/turbine performance and to prevent plant breakdowns.
Monitor and interpret DCS alarm indications of equipment malfunctions and coordinate with the Shift
Supervisor and Auxiliary Operator for alarm rectification.
Operate the control systems of the power plant substation equipment and HV/LV switchgear during
plant maintenance activities, emergency situations or as required.
Troubleshoot any plant abnormalities during the shift and initiate remedial measures to prevent
unnecessary downtimes/breakdowns.
Communicate with the load plant dispatchers to regulate and coordinate line voltages, transmission
loads and frequencies at normal plant operation.
Coordinate with all personnel concerned/affected during plant equipment maintenance, servicing and
testing.
Assist in the implementation of the plant’s policies, SOPs, safety procedures, good housekeeping,
energy conservation guidelines and environmental regulations.
Auxiliary Plant Operator (Turbine and Boiler) September 2015 to November 2021
Fill up the log sheets at pre-determined interval at each shift covering all duty equipment auxiliaries and
monitoring gauges and instrument outside of the plant control room.
Collect and evaluate actual data and information’s from Operation’s and check for any deviation from
established operating parameters set both for this operation. Promptly informs Shift Supervisor and
Control Room Engineer for any deviation and take necessary actions to correct it.
Closely coordinate with the Control Room Engineer during actual change-over of major plant equipment
and system auxiliaries following the established schedule and SOPs.
Initiate initial assessment and/or trouble-shooting of malfunctioned equipment during operation.
Report promptly to immediate superior all problems observed and encountered during operations and
seek immediate assistance from maintenance personal if problems at hand cannot be fixed.
Maintains good housekeeping and 5S practices with its area of concern at all times.
Closely coordinate with the Control Room Engineer during Start-up and shut downs of all plant
equipment and system auxiliaries following established SOPs.
Perform other functions as may be assigned from time to time such as but not limited to tasks related to
the job; projects and other improvement activities within the department or in coordination with other
sections, functions of the position/s if undergoing multi-skilling or cross training and other committee
functions in case designated.
SMC Global Power Holdings Corporation
Limay, Bataan, Philippines
Cadet Engineer November 2014 to September 2015
An extensive cadetship program with classroom and actual training in Power Plant, Introduction to
Circulated Fluidized Bed Boiler.; Draft and Flue Gas System, Limestone Feeding System, Auxiliary
Cooling System, Soot blowing System, Boiler water Circulation System, Fluidizing and Combustion
System ,Diesel Oil Firing System, Coal Handling System, Boiler and Turbine Protection, Condenser
Cleaning System, Feed water System ,Condensate System, Plant and Industrial Air System, Air
compressor System, Water and Wastewater treatment system, Sand System, Bottom ash and Fly ash
system, Turbine Extraction System, Turbine Generator System, Turbine Synchronization System, Gland
and vacuum system, Sea water circulation system, Flash and Blowdown system.
Regularly monitor the plant equipment and reports to the operation technician any abnormality.
_______________________________________________________________________________________
Education:
Tertiary: University of Southeastern Philippines-Bislig Campus
Brgy. Maharlika, Bislig City, Surigao Del Sur
Bachelor of Science in Mechanical Engineering (2007 to 2013)
Vocational: De La salle John Bosco College
Machining- NC II (2009)
Secondary: Northern Mindanao College (2007)
Cabadbaran, Agusan Del Norte
__________________________________________________________________________________________
Affiliations:
Philippines Society of Mechanical Engineers Davao Chapter – Member from 2013 to Present
Philippines Society of Mechanical Engineers Davao Occidental – Member from 2017 to Present
Mechanical Engineering Student Society – President S.Y 2012 to 2013
Mechanical Engineering Student Society – Vice President S.Y 2011 to 2012
Mechanical Engineering Student Society – Auditor S.Y 2010 to 2011
Communication Link and Emergency Assistance Network – Member Auxiliary
__________________________________________________________________________________________
Seminars and Training s Attended:
Philippine Red Cross – Basic Life Support and First Aid Training 2015
th
64 Philippine Society of Mechanical Engineers – National Convention – “In Pursuit of Technical
Advancement for Global Recognition 2016
Basic Wholesale Electricity Spot Market (WESM)
In Safety Inc. - Basic Occupational Safety and Health (BOSH) 2017
Bureau of Fire in the Philippines (BFP) – Basic Fire Fighting Training 2017
st
1 Industrial Pollution Control and Ash Handling (IPCA) Technical Training and Seminar 2018
MFI Institute Inc. – Industrial Process and Control 2018
The Blue Energy - Boiler Operation and Maintenance Essentials. 2022
MFI Institute Inc. – Instrumentation and Control Essentials 2022
_________________________________________________________________________________________
_Personal Information:
I hereby declare that all the above-mentioned information given by me is true and correct to the best of my
knowledge and belief.
ANDRIAN B. YTOM
Applicant