Smart Energy & Power Quality Solutions

Power Analyser

UMG 96RM-M
Data sheet
02/2019
Dok.-Nr. 2.040.178.0
 DEVICE VIEWS
UMG 96RM-M

Front view Rear view

Side view Bottom view

max. 6
□ 96

□ 91,5

104

□ 91,5

97

Cut-out size: 92+0,8 mm x 92+0,8 mm.

42

All dimensions in mm

2 – Data sheet UMG 96RM-M • 02/2019

TECHNICAL DATA

UMG 96RM-M
General
Net weight (with attached connectors) 300g
Packaging weight (including accessories) 625g
Device dimensions ca. l = 42mm, w = 97mm, h = 100mm
Service life of the backlight 40,000 hours (50% of initial brightness)

Transport and storage

The following information applies for devices that are transported or stored in their original packaging.
Free fall 1m
Temperature K55 (-25 °C to +70 °C)
Relative humidity 0 to 90% RH

Ambient conditions during operation

The UMG 96RM-M is intended for use in weather-protected, fixed locations.
Protection class II according to IEC 60563 (VDE 0106, part 1).
Rated temperature range K55 (-10 °C .. +55 °C)
Relative humidity 0 to 75 % RH
Operational altitude 0 .. 2000 m above sea level
Degree of pollution 2
Installation position vertical
Ventilation Forced ventilation is not required.
Foreign body and water protection
- Front IP40 according to EN60529
- Back IP20 according to EN60529
- Front with seal IP54 according to EN60529

Power supply voltage

Option 230V Nominal range 90V - 277V (50/60Hz) or DC 90V - 250V; 300V
CATIII
Power consumption max. 4.5VA / 2W
Option 24V Nominal range 24V - 90V AC / DC; 150V CATIII
Power consumption max. 2.5VA / 2W
Operating range +-10% of nominal range
Internal fuse, not replaceable Typ T1A / 250V/277V according IEC 60127
Recommended overcurrent protection device for line pro- Option 230V: 6 - 16A
tection (certified under UL) Option 24V: 1 - 6A
(Char. B)

Recommendation for a maximum number of devices on a circuit breaker:

Option 230V : Circuit breaker B6A: max. 4 devices / Circuit breaker B16A: max. 12 devices
Option 24V : Circuit breaker B6A: max. 12 devices / Circuit breaker B16A: max. 35 devices

Connection capacity of the terminals (power supply)

Connectable conductor. Only one conductor may be connected per contact point!
Single-wire, multi-wire, finely stranded conductor 0.2 - 2.5mm2, AWG 26 - 12
Pin terminals, ferrules 0.2 - 2.5mm2
Tightening torque 0.4 - 0.5Nm
Stripping length 7mm

02/2019 • Data sheet UMG 96RM-M – 3

UMG 96RM-M

Outputs
2 digital outputs, semi-conductor relay, not short circuit protected.
Switching voltage max. 33V AC, 60V DC
Switching current max. 50mAeff AC/DC
Reaction time 10/12 periods + 10ms *
Pulse output (energy pulses) max. 50Hz

* Reaction time at 50 Hz, for example: 200 ms + 10 ms = 210 ms

Connection capacity of the terminals (outputs)

Rigid/flexible 0.14 - 1.5mm2, AWG 28-16
Flexible with ferrules without plastic sleeve 0.20 - 1.5mm2
Flexible with ferrules with plastic sleeve 0.20 - 1.5mm2
Tightening torque 0.20 - 0.25Nm
Stripping length 7mm

Voltage metering
Three-phase, 4-wire systems with nominal voltages 277V/480V (+-10%)
up to
Three-phase, 3-wire systems, unearthed, IT 480V (+-10%)
with nominal voltages up to
Overvoltage category 300V CAT III
Rated surge voltage 4kV
Metering range L-N 01) .. 300 Vrms
(max. overvoltage 520 Vrms )
Metering range L-L 01) .. 520Vrms
(max. overvoltage 900Vrms )
Resolution 0.01V
Crest factor 2.45 (relative to the metering range)
Impedance 3MΩ/phase
Power consumption approx. 0.1 VA
Sampling rate 21.33 kHz (50 Hz), 25.6 kHz (60 Hz) per measuring
channel
Mains frequency 45 Hz .. 65 Hz
- Resolution 0.01 Hz

1)
The UMG 96RM-M can only detect measurements when a voltage L1-N greater than 20V eff
(4-wire measurement) at voltage input V1 or a voltage L1-L2 greater than 34V eff
(3-wire measurement) is applied.

4 – Data sheet UMG 96RM-M • 02/2019

 UMG 96RM-M
Current measurement
Rated current 5A
Metering range 0 .. 6Arms
Crest factor 1.98
Resolution 0.1 mA (display 0.01 A)
Overvoltage category 300V CAT II
Rated surge voltage 2kV
Power consumption ca. 0.2 VA (Ri=5mOhm)
Overload for 1 sec. 120 A (sinusoidal)
Sampling rate 21.33 kHz (50 Hz), 25.6 kHz (60 Hz) per measuring
channel

Connection capacity of the terminals (voltage and current measurement)

Connectable conductor. Only one conductor may be connected per contact point!
Current Voltage
Single-wire, multi-wire, finely stranded conductor 0.2 - 2.5mm , AWG
2
0.08 - 4.0mm2, AWG
26-12 28-12
Pin terminals, ferrules 0.2 - 2.5mm2 0.2 - 2.5mm2
Tightening torque 0.4 - 0.5Nm 0.4 - 0.5Nm
Stripping length 7mm 7mm

Serial interface
M-Bus 300, 600, 1200, 2400, 4800, 9600, 19200, 38400 baud
M-Bus device load max. 20 mA
Stripping length 7mm

Connection capacity of the terminals (M-Bus)

Single-wire, multi-wire, finely stranded conductor 0.20 - 1.5mm2
Pin terminals, ferrules 0.20 - 1.5mm2
Tightening torque 0.20 - 0.25Nm
Stripping length 7mm

02/2019 • Data sheet UMG 96RM-M – 5

UMG 96RM-M

FUNCTION PERFORMANCE CHARACTERISTICS

Function Symbol Accuracy class Metering range Display range
Total real power P 0.5 5)
(IEC61557-12) 0 .. 5.4 kW 0 W .. 999 GW *
Total reactive power QA, Qv 1 (IEC61557-12) 0 .. 5.4 kvar 0 varh .. 999 Gvar *
Total apparent power SA, Sv 0.55) (IEC61557-12) 0 .. 5.4 kVA 0 VA .. 999 GVA *
Total active energy Ea 0.55) (IEC61557-12) 0 .. 5.4 kWh 0 Wh .. 999 GWh *
0.5S5) (IEC62053-22)
Total reactive energy ErA, ErV 1 (IEC61557-12) 0 .. 5.4 kvarh 0 varh .. 999 Gvarh *
Total apparent energy EapA, 0.55) (IEC61557-12) 0 .. 5.4 kVAh 0 VAh .. 999 GVAh *
EapV
Frequency f 0.05 (IEC61557-12) 45 .. 65 Hz 45.00 Hz .. 65.00 Hz
Phase current I 0.2 (IEC61557-12) 0 .. 6 Arms 0 A .. 999 kA
Measured neutral conductor IN - - -
current I4
Calculated neutral conductor INc 1.0 (IEC61557-12) 0.03 .. 25 A 0.03 A .. 999 kA
current
Voltage U L-N 0.2 (IEC61557-12) 10 .. 300 Vrms 0 V .. 999 kV
Voltage U L-L 0.2 (IEC61557-12) 18 .. 520 Vrms 0 V .. 999 kV
Displacement factor PFA, PFV 0.5 (IEC61557-12) 0.00 .. 1.00 0.00 .. 1.00
Short-term flicker, long-term Pst, Plt - - -
flicker
Voltage dips (L-N) Udip - - -
Voltage surges (L-N) Uswl - - -
Transient overvoltages Utr - - -
Voltage interruptions Uint - - -
Voltage unbalance (L-N) 1) Unba - - -
Voltage unbalance (L-N) 2)
Unb - - -
Voltage harmonics Uh Class 1 (IEC61000-4-7) up to 2.5 kHz 0 V .. 999 kV
THD of the voltage 3) THDu 1.0 (IEC61557-12) up to 2.5 kHz 0 % .. 999 %
THD of the voltage 4) THD-Ru - - -
Current harmonics Ih Class 1 (IEC61000-4-7) up to 2.5 kHz 0 A .. 999 kA
THD of the current 3) THDi 1.0 (IEC61557-12) up to 2.5 kHz 0 % .. 999 %
THD of the current 4)
THD-Ri - - -
Mains signal voltage MSV - - -

1)
Referred to amplitude. * The display returns to 0 W when the
2)
Referred to phase and amplitude. maximum total energy values are reached.
3
) Referred to mains frequency.
4)
Referred to root mean square value.
5)
Accuracy class 0.5/ 0.5S with ../5 A transformer.
Accuracy class 1 with ../1 A transformer.

6 – Data sheet UMG 96RM-M • 02/2019

Smart Energy & Power Quality Solutions

Janitza electronics GmbH

Vor dem Polstück 6
35633 Lahnau, Germany
Support Tel. +49 6441 9642-22
Fax +49 6441 9642-30
e-mail: [email protected]
www.janitza.com