TQL9063

®
Ultra Low-Noise, Bypass LNA

Product Overview
The TQL9063 is a high-linearity, ultra-low noise gain block
amplifier with a bypass mode functionality integrated in the
product. At 1.95 GHz, the amplifier typically provides 19 dB
gain, +36.3 dBm OIP3, and 0.7 dB noise figure while
drawing 77 mA current from a +5 V supply. The component 8-pin 2x2 mm DFN Package
also provides high linearity in the bypass mode with +39
dBm IIP3.
Key Features
The TQL9063 is internally matched using a high-
• 0.5 – 4.0 GHz Operational bandwidth
performance E-pHEMT process and only requires four
external components for operation from a single positive • LNA with integrated bypass mode
supply: an external RF choke and blocking/bypass • Ability to turn LNA and bypass mode OFF
capacitors. This low noise amplifier contains an internal • Ultra-low noise, 0.7 dB at 1.95 GHz
active bias to maintain high performance over temperature. • 19 dB Gain at 1.95 GHz
• +36.3 dBm Output IP3 in LNA Mode
The TQL9063 covers the 0.5 – 4.0 GHz frequency band and • +39 dBm Input IP3 in Bypass Mode
is targeted for wireless infrastructure. The TQL9063 is
• Internally matched
packaged in a 2 x 2 mm DFN.
• Positive supply only, +3.3 to +5 V
• 2x2 mm 8-pin DFN plastic package

Functional Block Diagram Applications

• Base Station Receivers
Pin 1 Reference Mark
• Tower Mount Amplifiers
• Repeaters
GND 1 8 VDD • FDD-LTE, TDD-LTE, WCDMA
RF In 2 7 RF Out • General Purpose Wireless

VBYP 3 6 VSD
N/C 4 5 N/C

Backside Paddle - RF/DC GND

Top View
Ordering Information
Part No. Description
TQL9063 500−4000 MHz Bypass LNA
TQL9063-PCB 500−4000 MHz Evaluation Board
Standard T/R size = 2500 pieces on a 7” reel

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 1 of 12 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Absolute Maximum Ratings Recommended Operating Conditions

Parameter Rating Parameter Min Typ Max Units
Storage Temperature −65 to 150 °C Device Voltage (VDD) +3.3 +5.0 +5.25 V
RF Input Power, CW, 50 Ω, T=+25 °C +22 dBm TCASE −40 +105 °C
Device Voltage (VDD) +7 V Tj for >106 hours MTTF +190 °C
Operation of this device outside the parameter ranges given Electrical specifications are measured at specified test
above may cause permanent damage. conditions. Specifications are not guaranteed over all
recommended operating conditions.

Electrical Specifications
Test conditions unless otherwise noted: VDD = +5 V, Temp.=+25°C.
Parameter Conditions Min Typ Max Units
Operational Frequency Range 500 4000 MHz
Test Frequency 1950 MHz
Gain LNA ON, Bypass OFF 17.5 19 20.5 dB
Input Return Loss LNA ON, Bypass OFF 12 dB
Output Return Loss LNA ON, Bypass OFF 9.5 dB
Noise Figure LNA ON, Bypass OFF 0.7 0.9 dB
Output P1dB LNA ON, Bypass OFF +21.2 dBm
LNA ON, Bypass OFF,
Output IP3 +31 +36.3 dBm
Pout=+0 dBm/tone, Δf=1 MHz
Insertion Loss LNA OFF, Bypass ON 1.4 dB
Return Loss LNA OFF, Bypass ON 18 dB
LNA OFF, Bypass ON
Input IP3 +39 dBm
Pin=+3 dBm/tone, Δf=1 MHz
Isolation LNA OFF, Bypass OFF 17 dB
VIH 1.6 VDD V
Control Voltage, V1, V2 (1)
VIL 0 0.5 V
Bypass OFF 60 77 100 mA
Current, ID
Bypass ON 3 mA
Bypass to LNA Mode 983 ns
Switching Time (2) LNA to Bypass Mode 1.9 µs
LNA to OFF 200 ns
Thermal Resistance, θjc Channel to case 44 °C/W
Notes:
1. These voltages are referenced at the turrets labelled V1 and V2 on the circuit schematic on page 4.
2. To achieve fast-switching it is required to place a 91K shunt resistor at the RF Out pin 7. Refer to page 7.

Control Truth Table

VBYP VSD State
0 0 LNA ON, Bypass OFF
0 1 LNA OFF, Bypass OFF
1 x LNA OFF, Bypass ON

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 2 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

De-embedded S-Parameters (LNA Mode)

Test Conditions: VDD=+5 V, IDD=75 mA (typ.), T=+25°C, 50 ohm system impedance, reference on device leads
Freq (GHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang)
0.1 -0.34 -18.46 10.47 -40.24 -49.61 153.06 -0.20 -49.20
0.3 -2.46 -56.16 25.14 -126.62 -33.50 92.83 -4.56 -154.92
0.4 -4.03 -65.89 26.03 -156.47 -31.84 74.30 -8.52 162.29
0.6 -5.84 -77.87 25.55 166.99 -30.62 57.06 -14.43 89.93
0.7 -6.38 -83.02 25.03 154.63 -30.24 52.96 -15.50 58.24
0.8 -6.80 -87.84 24.47 144.39 -29.91 50.25 -15.55 32.10
1 -7.45 -96.37 23.34 127.97 -29.31 47.05 -14.41 -4.20
1.2 -7.92 -103.39 22.23 114.95 -28.74 45.37 -13.04 -27.33
1.3 -8.11 -106.38 21.70 109.30 -28.47 44.80 -12.41 -36.16
1.4 -8.27 -109.05 21.18 104.07 -28.20 44.35 -11.83 -43.80
1.5 -8.41 -111.43 20.67 99.21 -27.93 43.96 -11.30 -50.53
1.6 -8.52 -113.55 20.18 94.65 -27.67 43.62 -10.81 -56.56
1.7 -8.62 -115.44 19.69 90.36 -27.42 43.31 -10.36 -62.02
1.8 -8.71 -117.11 19.23 86.30 -27.17 43.01 -9.95 -67.01
1.9 -8.78 -118.58 18.77 82.44 -26.92 42.72 -9.57 -71.62
2 -8.83 -119.88 18.33 78.75 -26.68 42.42 -9.22 -75.91
2.1 -8.88 -121.03 17.90 75.22 -26.45 42.13 -8.90 -79.92
2.2 -8.91 -122.03 17.48 71.83 -26.22 41.83 -8.60 -83.70
2.3 -8.93 -122.92 17.07 68.57 -26.00 41.51 -8.33 -87.26
2.4 -8.94 -123.69 16.66 65.42 -25.78 41.19 -8.08 -90.64
2.5 -8.94 -124.36 16.27 62.37 -25.56 40.86 -7.85 -93.86
2.6 -8.92 -124.95 15.89 59.42 -25.35 40.52 -7.64 -96.93
2.7 -8.91 -125.47 15.52 56.55 -25.15 40.17 -7.45 -99.87
2.8 -8.88 -125.92 15.15 53.76 -24.95 39.81 -7.27 -102.69
3 -8.80 -126.67 14.45 48.39 -24.56 39.06 -6.97 -108.03
3.2 -8.69 -127.26 13.77 43.26 -24.18 38.26 -6.73 -113.00
3.4 -8.56 -127.74 13.12 38.32 -23.82 37.41 -6.53 -117.68
3.6 -8.41 -128.16 12.50 33.56 -23.46 36.52 -6.39 -122.10
3.8 -8.24 -128.54 11.90 28.94 -23.12 35.57 -6.30 -126.30
4 -8.05 -128.93 11.32 24.43 -22.78 34.56 -6.26 -130.29

Noise Parameters (LNA Mode)

Test conditions unless otherwise noted: VDD=+5 V, IDD=75 mA (typ.), Temp=+25°C, 50 Ohm system impedance
Freq (GHz) NFmin (dB) GammaOpt (mag) GammaOpt (deg) Rn (Ω)
1.5 0.46 0.27 73.07 3.17
1.6 0.47 0.27 76.39 3.15
1.7 0.47 0.28 79.57 3.14
1.8 0.48 0.28 82.63 3.12
1.9 0.49 0.29 85.57 3.11
2 0.50 0.29 88.39 3.10
2.1 0.50 0.30 91.10 3.08
2.2 0.51 0.31 93.70 3.07
2.3 0.52 0.31 96.20 3.06
2.4 0.53 0.32 98.60 3.04
2.5 0.54 0.33 100.91 3.03
2.6 0.55 0.33 103.13 3.02
2.7 0.56 0.34 105.27 3.00

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 3 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

TQL9063-PCB Evaluation Board

C5

J3 VDD
R1
R1
0 1 uF
C6 C6
C5
J8 GND
L1

1000 pF
C1 U1 C2 L1
68 nH
(0603)
C7 C8 U1
R2

R3

C1 1 8 C2
J1 J2
2 7
RF RF
Input 100 pF C7 3 6 27 pF C8 Output
4 5

100 pF 100 pF
R2 R3
C3 C4 0 0

J4 V2 J5 V1

See Evaluation Board PCB Information section for PCB material and stack-up.

Bill of Material – TQL9063-PCB

Reference Des. Value Description Manuf. Part Number
U1 - LNA, with bypass mode Qorvo TQL9063
C2 27 pF CAP, 5%, 50V, NPO/C0G, 0402 Various
C1, C3, C4, C7, C8 100 pF CAP, 5%, 50V, 0402 Panasonic ECJ-0EC1H101J
C6 1000 pF CAP, 10%, 50V, 0402 various
C5 1.0 µF CAP, 10%, 10V, X7S, 0402 various
R1, R2, R3 0Ω RES, 1/10W, 0402 various
L1 68 nH IND, 5%, CER CORE, 0603 Coilcraft 0603CS-68NXJL

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 4 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Typical Performance (LNA Mode)

Test conditions unless otherwise noted: VDD = +5 V, V1 = 0.5V, V2 = 0.5V, ID = 77 mA, Temp.=+25 °C.
Parameter Typical Value Units
Frequency 700 1950 2600 3500 MHz
Gain +24.3 19.2 17.3 14 dB
Noise Figure 0.64 0.7 0.8 1.1 dB
Input Return Loss 7.8 12 15.3 13.7 dB
Output Return Loss 9.4 9.3 9.5 6 dB
OIP3 (Pout/tone=+0 dBm, Δf = 1 MHz) +35.5 +36.3 +36.1 +36.4 dBm
P1dB +21.7 +21.2 +21.6 +19.8 dBm

Typical Performance (Bypass Mode)

Test conditions unless otherwise noted: VDD = +5 V, V1 = 0.5V or 1.6V, V2 = 1.6V, Id = 3 mA, Temp.=+25 °C.
Parameter Typical Value Units
Frequency 700 1950 2600 3500 MHz
Insertion Loss 1.2 1.4 1.5 1.6 dB
Input Return Loss 13.6 20 25 20 dB
Output Return Loss 13.6 18 18 17 dB
Input IP3 (Pin/tone=+3 dBm, Δf = 1 MHz) +38.2 +39 +39 +36.6 dBm

Typical Performance (LNA OFF, Bypass OFF Mode)

Test conditions unless otherwise noted: VDD = +5 V, V1 = 1.6V, V2 = 0.5V, Temp. = +25 °C.
Parameter Typical Value Units
Frequency 700 1950 2600 3500 MHz
Isolation 23 17 15 15 dB

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 5 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Performance Plots
Test conditions unless otherwise noted: VDD = +5 V
Gain vs. Frequency (LNA Mode) Input Return Loss vs. Frequency (LNA Mode) Output Return Loss vs. Frequency (LNA Mode)
30 0 0

Output Return Loss (dB)

25

Input Return Loss (dB)

+85°C -5 -5
+25°C
+85°C
Gain (dB)

20 −40°C
+25°C
-10 -10
−40°C
15
+85°C
+25°C
-15 -15
10 −40°C

5 -20 -20
500 1000 1500 2000 2500 3000 3500 4000 500 1000 1500 2000 2500 3000 3500 4000 500 1000 1500 2000 2500 3000 3500 4000
Frequency (MHz) Frequency (MHz) Frequency (MHz)
Gain vs. Frequency (Bypass Mode) Input Return Loss vs. Frequency (Bypass Mode) Output Return Loss vs. Frequency (Bypass Mode)
0 0 0

-5

Output Return Loss (dB)

-1 -5
Input Return Loss (dB)

-10 +85°C
+85°C
Gain (dB)

-2 +25°C -10
−40°C +25°C
+85°C -15
−40°C
-3 +25°C -15
−40°C -20

-4 -20
-25

-5 -30 -25
500 1000 1500 2000 2500 3000 3500 4000 500 1000 1500 2000 2500 3000 3500 4000 500 1000 1500 2000 2500 3000 3500 4000
Frequency (MHz) Frequency (MHz) Frequency (MHz)
Gain vs. Frequency (OFF Mode) Input Return Loss vs. Frequency (OFF Mode) Output Return Loss vs. Frequency (OFF Mode)
-10 0 0
+85°C
+25°C
-1 Output Return Loss (dB) -1
Input Return Loss (dB)

−40°C +85°C
-15
+25°C
−40°C
Gain (dB)

-2 -2
-20
+85°C
-3 -3
+25°C
−40°C
-25
-4 -4

-30 -5 -5
500 1000 1500 2000 2500 3000 3500 4000 500 1000 1500 2000 2500 3000 3500 4000 500 1000 1500 2000 2500 3000 3500 4000
Frequency (MHz) Frequency (MHz) Frequency (MHz)
Noise Figure vs. Frequency OIP3 vs Pout (LNA Mode) OIP3 vs Pout (LNA Mode)
1.6 39 45
Temp.=+25°C Frequency = 1950 MHz
+85°C
1.4
+25°C +85°C
38 42
1.2 −40°C +25°C
Noise Figure (dB)

−40°C
OIP3 (dBm)

OIP3 (dBm)

1 37 39
0.8

0.6 36 36

0.4 700MHz
35 1950MHz 33
0.2 2600Mhz
3500MHz
0 34 30
500 1000 1500 2000 2500 3000 3500 4000 -4 -2 0 2 4 6 8 -4 -2 0 2 4 6 8
Frequency (MHz) Pout/tone (dBm) Pout/tone (dBm)
OIP3 vs Pout (Bypass Mode) OIP3 vs Pout (Bypass Mode) P1dB vs. Frequency (LNA Mode)
45 45 30
Temp.=+25°C Frequency = 1950 MHz +85°C +85°C
+25°C +25°C
42 42 −40°C
−40°C 25
P1dB (dBm)
OIP3 (dBm)

OIP3 (dBm)

39 39
20
36 36

15
33 700MHz 33
1950MHz
2600Mhz
3500MHz
30 30 10
-4 -2 0 2 4 6 -4 -2 0 2 4 6 500 1000 1500 2000 2500 3000 3500 4000
Pout/tone (dBm) Pout/tone (dBm) Frequency (MHz)

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 6 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Switching Time

R1 C5

C6
J3 VDD
C5 R1
0 1000 pF
L1

C6
J8 GND
R4

J1 C1 U1 C2 J2
1 uF
L1
C7 C8
18 nH
(0603)
R2

R3

U1

C1 1 8 C2
J1 J2
2 7
RF R4 RF
Input 100 pF C7 3 6 91K 100 pF Output
C8
4 5

100 pF 100 pF
C3 C4 R2 R3
J6 J7
0 0

J4 V2 J5 V1

Transition Value Units

Bypass to LNA mode 983 ns
LNA to Bypass mode 1.9 µs

R4, valued 91K, is required to achieve the switching times listed above. The placement of R4 is shown on the Qorvo EVB above .

Bypass to LNA mode transition LNA to Bypass mode transition

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 7 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

TQL9063 – Optimized Return Loss Tune

C5
J3 VDD
R1
R1
0 1 uF
C6
C5 C6
J8 GND
L1

C9

1000 pF
J1 C1 U1 L2 C2 J2
L1
68 nH
(0603)
C7 C8
U1
R2

R3

C1 1 8
J1 L2 J2
2 7
C2
1 nH
RF 27 pF C9 RF
Input 100 pF 3 6 Output
C7 C8 0.5 pF
4 5

10 pF 10 pF
R2 R3
J6 C3 C4 J7 0 0

J4 V2 J5 V1

See Evaluation Board PCB Information section for PCB material and stack-up.

Bill of Material – Optimized Return Loss Tune

Reference Des. Value Description Manuf. Part Number
U1 - Bypass LNA Qorvo TQL9063
C2 27 pF CAP, 5%, 50V, NPO/C0G, 0402 Various
C1, C3, C4 100 pF CAP, 5%, 50V, 0402 Panasonic ECJ-0EC1H101J
C6 1000 pF CAP, 10%, 50V, 0402 various
C5 1.0 µF CAP, 10%, 10V, X7S, 0402 various
C9 0.5 pF CAP, ±0.1pF, 50V, 0402 Murata GJM1555C1HR50BB01D
R1, R2, R3 0Ω RES, 1/10W, 0402 various
L1 68 nH IND, 5%, CER CORE, 0603 Coilcraft 0603CS-68NXJL
L2 1 nH IND, ±0.1nH, 0402 Murata LQP15MN1N0B

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 8 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Performance Plots- Optimized Return Loss

Test conditions unless otherwise noted: VDD = +5 V

Gain vs. Frequency Input Return Loss vs. Frequency Output Return Loss vs. Frequency
20 0 0

-5
15
-5
-10
10

|S22| (dB)
|S11| (dB)
Gain (dB)

-15 -10
LNA Mode
5
Bypass Mode
-20
-15
0
-25
LNA Mode LNA Mode
Bypass Mode Bypass Mode
-5 -30 -20
2200 2300 2400 2500 2600 2700 2800 2900 2200 2300 2400 2500 2600 2700 2800 2900 2200 2300 2400 2500 2600 2700 2800 2900
Frequency (MHz) Frequency (MHz) Frequency (MHz)

OIP3 vs. Pout/tone Noise Figure vs Frequency

38 1.0
LNA Mode

37 0.9

Noise Figure (dB)

OIP3 (dBm)

36 0.8

2600 MHz
35 0.7
2650 MHz
2700 MHz

34 0.6

33 0.5
-4 -3 -2 -1 0 1 2 3 4 5 6 2600 2620 2640 2660 2680 2700
Pout/Tone (dBm) Frequency (MHz)

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 9 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Pin Configuration and Description

Pin 1 Reference Mark

GND 1 8 VDD
RF In 2 7 RF Out
VBYP 3 6 VSD
N/C 4 5 N/C

Backside Paddle - RF/DC GND

Pin No. Label Description

1 GND RF/DC Ground pin.
2 RF In RF input pin. DC block required.
Control pin for bypass mode. The LNA is automatically turned off when the
3 VBYP
bypass mode is activated. Refer to truth table.
No internal connection. Provide grounded PCB land pads for mounting
4, 5 N/C
integrity.
6 VSD Control pin to disable the LNA. Refer to truth table.
7 RF Out RF output pin. DC block required.
8 VDD Supply voltage pin.
RF/DC Ground. Follow recommended via pattern and ensure good solder
Backside Paddle RF/DC GND
attach for best thermal and electrical performance.

Evaluation Board PCB Information

Qorvo PCB 1121181 Material and Stack-up

1 oz. Cu top layer

0.010" Rogers 4350B
1 oz. Cu inner layer
0.062" ± 0.006"
Finished Board
Thickness Rogers 4450F

1 oz. Cu inner layer

0.010" Rogers 4350B
1 oz. Cu bottom layer

50 ohm line dimensions: width = .020”, spacing = .032”

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 10 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Mechanical Information
Package Marking and Dimensions

0.800±0.050
2.000±0.050 Exp. DAP
Pin 1 Identifier Pin 1 Identifier
0.200x45°

0.850±0.050
9063 1.600±0.050
2.000±0.050 0.500 BSC
Trace Exp. DAP
Code

0.300±0.050 0.250±0.050 0.00-0.05 0.203 Ref

TOP VIEW BOTTOM VIEW SIDE VIEW

Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Except where noted, this part outline conforms to JEDEC standard MO-229.
3. Dimension and tolerance formats conform to ASME Y14.4M-1994.
4. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012.

PCB Mounting Pattern

Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Use 1 oz. copper minimum for top and bottom layer metal.
3. Vias are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. We recommend a 0.35mm
(#80/.0135") diameter bit for drilling via holes and a final plated through diameter of 0.25 mm (0.010”).
4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance.

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 11 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Tape and Reel Information – Carrier and Cover Tape Dimensions

Feature Measure Symbol Size (in) Size (mm)

Length A0 0.091 2.30
Width B0 0.091 2.30
Cavity
Depth K0 0.039 1.30
Pitch P1 0.157 4.00
Cavity to Perforation - Length Direction P2 0.079 2.00
Centerline Distance
Cavity to Perforation - Width Direction F 0.138 3.50
Cover Tape Width (Reference Only) C 0.213 5.40
Carrier Tape Width W 0.315 8.00

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 12 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Tape and Reel Information – Reel Dimensions

Standard T/R size = 2500 pieces on a 7” reel.

Feature Measure Symbol Size (in) Size (mm)

Diameter A 6.969 177.0
Flange Thickness W2 0.559 14.2
Space Between Flange W1 0.346 8.8
Outer Diameter N 2.283 58.0
Arbor Hole Diameter C 0.512 13.0
Hub
Key Slit Width B 0.079 2.0
Key Slit Diameter D 0.787 20.0

Tape and Reel Information – Tape Length and Label Placement

Notes:
1. Empty part cavities at the trailing and leading ends are sealed with cover tape. See EIA 481-1-A.
2. Labels are placed on the flange opposite the sprockets in the carrier tape.

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 13 of 14 www.qorvo.com
 TQL9063
®
Ultra Low-Noise, Bypass LNA

Handling Precautions
Parameter Rating Standard
ESD – Human Body Model (HBM) Class 1B ESDA / JEDEC JS-001-2012 Caution!
ESD – Charged Device Model (CDM) Class C3 JEDEC JESD22-C101F ESD-Sensitive Device
MSL – Moisture Sensitivity Level Level 1 IPC/JEDEC J-STD-020

Solderability
Compatible with both lead-free (260°C max. reflow temp.) and tin/lead (245°C max. reflow temp.) soldering processes.
Solder profiles available upon request.
Contact plating: NiPdAu

RoHS Compliance
This part is compliant with the 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU. This product also has the following attributes:
• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free

Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: [email protected]

Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2023 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.

Datasheet, Rev G, October 11, 2023 | Subject to change without notice 14 of 14 www.qorvo.com