XLi Series Operation Manual

Models: XLi 800, XLi 1500, XLi 2500, XLi 3500

Obtaining Other Language Versions: To obtain information in another language about the use
of this product, please contact your local Crown Distributor. If you need assistance locating your
local distributor, please contact Crown at 574-294-8000.
This manual does not include all of the details of design, production, or variations of the equipment.
Nor does it cover every possible situation which may arise during installation, operation or
maintenance.
The information provided in this manual was deemed accurate as of the publication date. However,
updates to this information may have occurred. To obtain the latest version of this manual, please
visit the Crown website at www.crownaudio.com.
Later versions of this manual and additional information about this product may be available at the
Crown website at www.crownaudio.com.
Trademark Notice: Crown and Crown Audio are registered trademarks of Crown International.
Other trademarks are the property of their respective owners.
©2012 by Harman International. 1718 W. Mishawaka Rd., Elkhart, Indiana 46517-9439 U.S.A.
Telephone: 574-294-8000

5015442 - 04/12

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

Important Safety Instructions

1. Read these instructions. WATCH FOR THESE SYMBOLS:
2. Keep these instructions.
The lightning bolt triangle is used to alert the user to
3. Heed all warnings. the risk of electric shock.
4. Follow all instructions.
5. Do not use this apparatus near water. The exclamation point triangle is used to alert the
6. Clean only with a dry cloth. user to important operating or maintenance instruc-
7. Do not block any ventilation openings. Install in accordance with the
tions.
manufacturer’s instructions.
8.  Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. This device is designed and evaluated under the con-
A grounding-type plug has two blades and a third grounding prong. dition of 2000 meters tall above sea level; and, it can
The wide blade or the third prong is provided for your safety. If the ≤2000m be only used in locations below 2000 meters tall above
provided plug does not fit into your outlet, consult an electrician for
sea level. Using the device above 2000 meters altitude
replacement of the obsolete outlet.
would result in high safety risk.
10.  Protect the power cord from being walked on or pinched, particularly
at plugs, convenience receptacles, and the point where they exit from The device is designed and evaluated under the condi-
the apparatus. tion of non-tropical climate; and, it can be only used
11. Only use attachments/accessories specified by the manufacturer. in locations in non-tropical climate areas. Using the
device in tropical climate areas would result in high
12. Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. safety risk.
When a cart is used, use caution when moving the cart/ IMPORTANT
apparatus combination to avoid injury from tip-over.
XLi Series amplifiers require Class 2 output wiring.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time. MAGNETIC FIELD
14. Refer all servicing to qualified service personnel. Servicing is required CAUTION! Do not locate sensitive high-gain equipment such as
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects
preamplifiers or tape decks directly above or below the unit. Be-
have fallen into the apparatus, the apparatus has been exposed to rain cause this amplifier has a high power density, it has a strong mag-
or moisture, does not operate normally, or has been dropped. netic field which can induce hum into unshielded devices that are
15. Use the mains plug to disconnect the apparatus from the mains.
located nearby. The field is strongest just above and below the unit.
16. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO If an equipment rack is used, we recommend locating the
NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. amplifier(s) in the bottom of the rack and the preamplifier or
17. WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS other sensitive equipment at the top.
SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION.
18. DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR FCC COMPLIANCE NOTICE
SPLASHING AND ENSURE THAT NO OBJECTS FILLED This device complies with part 15 of the FCC rules. Operation is sub-
WITH LIQUIDS, SUCH AS VASES, ARE PLACED ON THE ject to the following two conditions: (1) This device may not cause
EQUIPMENT. harmful interference, and (2) this device must accept any interference
19. THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN received, including interference that may cause undesired operation.
READILY OPERABLE. CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP operate the equipment.
OR BOTTOM COVERS. NO USER SERVICEABLE PARTS NOTE: This equipment has been tested and found to comply with
INSIDE. REFER SERVICING TO QUALIFIED SERVICE the limits for a Class B digital device, pursuant to part 15 of the FCC
PERSONNEL. Rules. These limits are designed to provide reasonable protection
TO COMPLETELY DISCONNECT THIS EQUIPMENT against harmful interference in a residential installation. This equip-
FROM THE AC MAINS, DISCONNECT THE POWER ment generates, uses, and can radiate radio frequency energy and,
SUPPLY CORD PLUG FROM THE AC RECEPTACLE. THE if not installed and used in accordance with the instruction manual,
MAINS PLUG OF THE POWER SUPPLY CORD SHALL may cause harmful interference to radio communications. However,
REMAIN READILY OPERABLE. there is no guarantee that interference will not occur in a particular
WARNING: PAY ATTENTION TO A PROCEDURE, PRACTICE, CONDI-
installation. If this equipment does cause harmful interference to ra-
TION OR THE LIKE, IF NOT CORRECTLY PERFORMED OR ADHERED dio or television reception, which can be determined by turning the
TO, COULD RESULT IN PERSONAL INJURY OR DEATH. equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
CAUTION: PAY ATTENTION TO PROCEDURE, PRACTICE,
CONDITION OR THE LIKE, IF NOT CORRECTLY PERFORMED OR • Reorient or relocate the receiving antenna.
ADHERED TO, COULD RESULT IN DAMAGE OR DESTRUCTION TO • Increase the separation between the equipment and receiver.
PART OR ALL OF THE COMPONENT. • Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Operation Manual page 3

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

DECLARATION OF CONFORMITY

Issued By: Harman International.

1718 W. Mishawaka Rd.
Elkhart, IN 46517 U.S.A.

European Representative’s Name and Address:

David J. Budge
10 Harvest Close
Yateley
GU46 6YS
United Kingdom

Equipment Type: Commercial Audio Power Amplifiers

Family Name: XLi
Model Names: XLi 800, XLi 1500, XLi 2500, XLi 3500

EMC Standards:
EN 55103-1:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and
Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions
EN 55103-1:1997 Magnetic Field Emissions-Annex A @ 10 cm and 20 cm
EN 61000-3-2:2001 Limits for Harmonic Current Emissions (equipment input current less than or equal to 16 A per phase)
EN 61000-3-3:2002 Limitation of Voltage Fluctuations and Flicker in Low-Voltage Supply Systems Rated Current less than
or equal to16A
EN 55022:2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE: Radiated, Class B Limits;
Conducted, Class A
EN 55103-2:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and
Entertainment Lighting Control Apparatus for Professional Use, Part 2: Immunity
EN 61000-4-2:2001 Electrostatic Discharge Immunity (Environment E2-Criteria B, 4k V Contact, 8k V Air Discharge)
EN 61000-4-3:2001 Radiated, Radio-Frequency, Electromagnetic Immunity (Environment E2, criteria A)
EN 61000-4-4:2001 Electrical Fast Transient/Burst Immunity (Criteria B)
EN 61000-4-5:2001 Surge Immunity (Criteria B)
EN 61000-4-6:2003 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields (Criteria A)
EN 61000-4-11:2001 Voltage Dips, Short Interruptions and Voltage Variation
Safety Standard:
IEC 60065: 2001 7th Ed. Safety Requirements - Audio Video and Similar Electronic Apparatus

I certify that the product identified above conforms to the requirements of the EMC Council Directive 89/336/EEC as amended
by 92/31/EEC, and the Low Voltage Directive 73/23/EES as amended by 93/68/EEC.92/31/EEC, and the Low Voltage Directive
73/23/EES as amended by 93/68/EEC.

Signed _____________________________

Terry Davenport
Director of Manufacturing
Date of Issue: March 1, 2012

Due to line current harmonics, we recommend that you contact your supply authority before connection.

page 4 Operation Manual

Downloaded from www.Manualslib.com manuals search engine
 Operation Manual
Downloaded from www.Manualslib.com manuals search engine
Gain Control Power LED Fault LED
Sets ouptut level of Blue LED illuminates Red LED, one per channel,
each channel. when amplifier is on. indicates channel shutdown.
XLi Series Power Amplifiers

Front Panel Features

Rack-Mount Hole Power Switch Grill

(one of four) Push-on, push-off. Allows flow-through
ventilation from front to back.

Signal Presence LED Clip LED

Green LED, one per channel, Yellow LED, one per
flashes when input signal channel, flashes when
exceeds -40 dBu. signal is audibly distorting.

page 5
 page 6
Mode S witch
Stereo (dual), P arallel or Bridge .

Fans Input C onnec tors

Circuit Breaker Pro vide front to back One balanced XLR and one

Downloaded from www.Manualslib.com manuals search engine

Pro vides overload protec tion. fo rced air ow f or unbalanced RCA per channel .

BRIDGE
Back Panel Features

PARALLEL
XL 3500 STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

AC Power Output C onnec tors Sensitivity Switch

Connec to r One Speakon® and one 1.4V or 0.775V input
Binding P ost per channel sensitivit y.
connec t to loudspeakers .

Cordset rating: 10A, 250V

Cable Coating Material: Environmental Protection PVC, copper core PBT
XLi Series Power Amplifiers

Operation Manual
 XLi Series Power Amplifiers

Setup
Unpack and Install Your Amplifier
Please unpack and inspect your amplifier for any damage that may have occurred during transit. If damage
is found, notify the transportation company immediately. Only you can initiate a claim for shipping damage.
Crown will be happy to help as needed. Save the shipping carton as evidence of damage for the shipper’s
inspection.
We also recommend that you save all packing materials so you will have them if you ever need to transport
the unit. Never ship the unit without the factory pack.
YOU WILL NEED (not supplied):
• Input wiring cables
• Output wiring cables
• Ethernet cables
• Rack for mounting amplifier (or a stable surface for stacking)
WARNING: Before you start to set up your amplifier, make sure you read and
observe the Important Safety Instructions found at the beginning of this manual.
CAUTION: Before you begin, make sure your amplifier is disconnected from the
power source, with the power switch in the “off” position and all level controls
turned completely down (counterclockwise).
Use a standard 19-inch (48.3 cm) equipment rack (EIA RS-310B). See below figure for amplifier dimensions.

NOTE: When transporting, amplifiers should be supported at both front and back.

MAGNETIC FIELD
CAUTION! Do not locate sensitive high-gain equipment such as preamplifiers or
tape decks directly above or below the unit. Because this amplifier has a high
power density, it has a strong magnetic field which can induce hum into unshielded
devices that are located nearby. The field is strongest on the right side and right
bottom of the amplifier (facing the amplifier).
If an equipment rack is used, we recommend locating sensitive
equipment at least 20 cm (8 inches) away from the amplifier.
When using an equipment rack, mount units directly on top of each
other. Close any open spaces in rack with blank panels. DO NOT block
front or rear air vents. The side walls of the rack should be a minimum
of two inches (5.1 cm) away from the amplifier sides, and the back
of the rack should be a minimum of four inches (10.2 cm) from the
amplifier back panel.

Operation Manual page 7

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

Wiring
Stereo (Dual) Wiring Using the Speakon® Connectors
1. See Figure 3. On the back panel, set the Output Mode Switch to STEREO.
2. Wire the speakers to the Speakon® connectors as shown.

BRIDGE

XL 3500 PARALLEL

STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

Stereo (Dual) Wiring Using the Binding Post Connectors

1. See Figure 4. On the back panel, set the Output Mode Switch to STEREO.
2. Wire the speakers to the binding post connectors as shown.

BRIDGE

XL 3500 PARALLEL

STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

page 8 Operation Manual

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

Wiring
Bridge-Mono Wiring Using the Speakon® Connectors
Bridge-mono mode doubles the output power of the amplifier.
1. See Figure 5. On the back panel, set the Output Mode Switch to BRIDGE.
2. Wire the speaker to the Speakon® connector as shown.
3. Only the Channel 1 Gain Control works in Bridge-mono mode.

BRIDGE

XL 3500 PARALLEL

STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

Bridge-Mono Wiring Using the Binding Post Connectors

Bridge-mono mode doubles the output power of the amplifier.
1. See Figure 5. On the back panel, set the Output Mode Switch to BRIDGE.
2. Wire the speaker to the binding post connectors as shown.
3. Only the Channel 1 Gain Control works in Bridge-mono mode.

BRIDGE

XL 3500 PARALLEL

STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

Operation Manual page 9

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

Wiring
Parallel Wiring Using the Speakon® Connectors
With this wiring, a signal sent to one of the input connectors is paralleled to both channels so that it is reproduced
by both speakers.
1. See Figure 7. On the back panel, set the Output Mode Switch to PARALLEL.
2. Wire the speakers to the Speakon® connectors as shown.

BRIDGE

XL 3500 PARALLEL

STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

Parallel Wiring Using the Binding Post Connectors

With this wiring, a signal sent to one of the input connectors is paralleled to both channels so that it is reproduced
by both speakers.
1. See Figure 8. On the back panel, set the Output Mode Switch to PARALLEL.
2. Wire the speakers to the binding post connectors as shown.

BRIDGE

XL 3500 PARALLEL

STEREO
ODE
RESET Professional Audio Amplifier
Manufacture: Crown Audio Inc.
Made in China
220V ~ 50/60H
z 700W

SE SITI IT

UTPUTS INPUTS

page 10 Operation Manual

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

Specifications
Guaranteed Minimum Power XLi 800 XLi 1500 XLi 2500 XLi 3500
1 kHz (EIA) with 0.5% THD
4  stereo (per channel) 300W 450W 750W 1350W
8  stereo (per channel) 200W 330W 500W 1000W
8  bridge mono 600W 900W 1500W 2700W

Performance
Frequency Response (at 1 Watt) 20Hz - 20kHz, +0/-1dB
Total Harmonic Distortion (THD) < 0.5%, 20 Hz - 20 kHz
Intermodulation Distortion (IMD)
60 Hz and 7 kHz at 4:1, from full rated output  0.35%
to –30 dB
Slew Rate >10V/us
Voltage Gain 29dB 31dB 33dB 36dB
Damping Factor (8 ), 10 Hz - 400 Hz > 200
Signal-to-Noise Ratio (below rated power,
20 Hz to 20 kHz, A-weighted) > 100 dB
Crosstalk (below rated power)
At 1 kHz –75 dB
At 20 kHz –59 dB
Input Sensitivity for full rated power at 8  0.775V or 1.4V
Input Impedance (nominal)
Balanced 20 k
Unbalanced 10 k
Connectors, Controls and Indicators
Input Connectors One balanced XLR and one unbalanced RCA per channel
Output Connectors (Speaker Connectors) 4-POLE Speakon® and one pair Binding Post per channel
Front Panel Controls Power on/off switch, one gain control per channel
Rear Panel Controls Output mode switch: stereo (dual), parallel or bridge
Input sensitivity switch: 0.775V or 1.4V
Power Indicator One blue LED
Signal Indicator One green LED per channel
Clip (peak) Indicator One yellow LED per channel
Fault Indicator One red LED per channel
Construction
Protection Protection against short circuits, no-load, on/off muting,
RF interference. Stable into reactive or mismatched loads
Ventilation Flow-through ventilation from front to back
Cooling Internal heat sinks with forced air. Fan cooled,
speed regulated, thermal protection
Dimensions (W x H x D) 19" x 3.5" x 12.4" 19” x 3.5” x 14.4”
(482 mm x 89 mm x 315 mm) (482 x 89 x 366 mm)

Net Weight 25.1 lb (11.4 kg) 28.0 lb (12.7 kg) 29.7 lb (13.5 kg) 43.0 lb (19.5 kg)
Shipping Weight 29.5 lb (13.4 kg) 32.4 lb (14.7 kg) 34.2 lb (15.5 kg) 47.4 lb (21.5 kg)

Operation Manual page 11

Downloaded from www.Manualslib.com manuals search engine
 XLi Series Power Amplifiers

Warranty – USA Only

SUMMARY OF WARRANTY
Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL
PURCHASER and ANY SUB­SEQUENT OWNER of each NEW Crown1 product, for a period of one (1) year from the
date of pur­chase by the original purchaser (the “warranty period”) that the new Crown product is free of defects in
materials and workmanship, and we further warrant the new Crown product regardless of the reason for failure, except
as excluded in this Warranty.
Warranty is only Valid within the United States of America. For information on Warranty outside of the U.S.A, please
contact your local distributor.
ITEMS EXCLUDED FROM THIS CROWN­WARRANTY
This Crown Limited Warranty is in effect only for failure of a new Crown product which occurred within the Warranty
Period. It does not cover any product which has been damaged because of any inten­tional misuse, accident,
negligence, or loss which is covered under any of your insurance contracts. This Crown Warranty also does not
extend to the new Crown product if the serial number has been defaced, altered, or removed.
WHAT THE WARRANTOR WILL DO
We will remedy any defect, regardless of the reason for failure (except as excluded), by repair, replacement, or refund.
We may not elect refund unless you agree, or unless we are unable to provide replacement, and repair is not practical or
cannot be timely made. If a refund is elected, then you must make the defective or malfunctioning product available to
us free and clear of all liens or other encumbrances. The refund will be equal to the actual purchase price, not including
interest, insurance, closing costs, and other fi nance charges less a reasonable depreciation on the product from the date
of original purchase. Warranty work can only be performed at our authorized service centers or at the factory. We will
remedy the defect and ship the product from the service center or our factory within a reasonable time after receipt of the
defective product at our authorized service center or our factory. All expenses in remedying the defect, including surface
shipping costs in the United States, will be borne by us. (You must bear the expense of shipping the product between any
foreign country and the port of entry in the United States including the return shipment, and all taxes, duties, and other
customs fees for such foreign shipments.)
HOW TO OBTAIN WARRANTY SERVICE
You must notify us of your need for warranty service within the warranty period. All components must be shipped in a
factory pack, which, if needed, may be obtained from us free of charge. Corrective action will be taken within a reasonable
time of the date of receipt of the defective product by us or our authorized service center. If the repairs made by us or our
authorized service center are not satisfactory, notify us or our authorized service center immediately.
DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES
YOU ARE NOT ENTITLED TO RECOVER FROM US ANY INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN
THE NEW CROWN PRODUCT. THIS INCLUDES ANY DAMAGE TO ANOTHER PRODUCT OR PRODUCTS RESULTING
FROM SUCH A DEFECT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
WARRANTY ALTERATIONS
No person has the authority to enlarge, amend, or modify this Crown Warranty. This Crown Warranty is not extended
by the length of time which you are deprived of the use of the new Crown product. Repairs and replacement parts
provided under the terms of this Crown Warranty shall carry only the unexpired portion of this Crown Warranty.
DESIGN CHANGES
We reserve the right to change the design of any product from time to time without notice and with no obligation to
make corresponding changes in products previously manufactured.
LEGAL REMEDIES OF PURCHASER
THIS CROWN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE. No action to enforce this Crown Warranty shall be commenced after expiration of the
warranty period.
THIS STATEMENT OF WARRANTY SUPERSEDES ANY OTHERS CONTAINED IN THIS MANUAL FOR CROWN
PRODUCTS. 5/11
page 12 Operation Manual
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine