NSX-BL54 HT

NSX-BL54E HA

NSX-BL57 LH

SERVICE MANUAL BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM(HT)

BASIC TAPE MECHANISM : 2ZM-3MK2 YPR4NM(HA/LH)
COMPACT DISC
BASIC CD MECHANISM : AZG-1 ZA3RDM(HT)
STEREO SYSTEM
BASIC CD MECHANISM : AZG-1 YZA3RDCM(HA)
BASIC CD MECHANISM : AZG-1 YZA3RDM(LH)

CD REMOTE
SYSTEM SPEAKER
CASSEIVER CONTROLLER
NSX–BL54 CX–NBL54 SX–WNBL53

NSX–BL54E CX–NBL54E SX–WNBL53 RC–ZAS01

NSX–BL57 CX–NBL57 SX–WNBL53

• If requiring information about the CD mechanism, see Service Manual of AZG-1

(S/M Code No. 09-001-335-3NC).
TA
DA

S/M Code No. 09-002-429-5N5

 SPECIFICATIONS

Main unit CX-NBL54/CX-NBL54E/CX-NBL57 Cassette deck section

FM tuner section Track format 4 tracks, 2 channels stereo
Tuning range 87.5 MHz to 108 MHz Frequency response 50 Hz – 15000 Hz
Usable sensitivity (IHF) 13.2 dBf Recording system AC bias
Antenna terminal 75 ohms (unbalanced) Heads Deck 1: Playback head x 1
Deck 2: Recording/playback head
AM (MW) tuner section x 1, erase head x 1
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step) Compact disc player section
Usable sensitivity 350 µV/m Laser Semiconductor laser (λ = 780 nm)
Antenna Loop antenna D-A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
SW tuner section <HT> Harmonic distortion 0.05 % (1 kHz, 0 dB)
Tuning range 5.730 MHz to 17.900 MHz Wow and flutter Unmeasurable
Antenna Wire antenna

Amplifier section General

Mid-high frequency amplifier Power requirements 120 V/220 – 230 V/240 V AC,
Power output Rated: 20 W + 20 W (8 ohms, switchable 50/60 Hz
T.H.D. 1 %, 1 kHz) Power consumption 150 W
Reference : 25 W + 25 W (8 ohms, Power consumption in standby mode
T.H.D. 10 %, 1 kHz) If the power-economizing mode is
Total harmonic distortion 0.1 % (10 W, 1 kHz, 8 ohms, DIN ECO OFF: 20 W
AUDIO) If the power-economizing mode is
Low frequency amplifier ECO ON or ECO AUTO: 0.9 W
Power output Rated: 60 W + 60 W (6 ohms, Dimensions of main unit 260 x 326 x 346 mm
T.H.D. 1 %, 130 Hz) (W x H x D)
Reference : 75 W + 75 W (6 ohms, Weight of main unit 9.0 kg
T.H.D. 10 %, 130 Hz)
Total harmonic distortion 0.1 % (30W, 130 Hz, 6 ohms, DIN Speaker system SX-WNBL53
AUDIO) Speaker system 3 way, Built-in subwoofer (magnetic
Inputs VIDEO/AUX: 500 mV shielded type)
MIC 1.0 mV (10 k ohms) Speaker units Subwoofer: 160 mm cone type
Outputs SPEAKERS HIGH FREQ: Full range: 100 mm cone type
accept speakers of 8 ohms or more Super tweeter: 20 mm ceramic type
SPEAKERS LOW FREQ: Impedance 6 ohms/8 ohms
accept speakers of 6 ohms or more Sensitvity 87 dB/W/m
SURROUND SPEAKERS: Dimensions (W x H x D) 230 x 324 x 282 mm
accept speakers of 8 ohms to 16 Weight 4.8 kg
ohms
PHONES (stereo jack): accepts
headphones of 32 ohms or more
• Design and specifications are subject to change without notice.
• The word “BBE” and the “BBE symbol” are trademarks of BBE
Sound, Inc.
• Under license from BBE Sound, Inc.

ACCESSORIES LIST

REF. NO PART NO. KANRI DESCRIPTION

NO.
1 8A-NFJ-930-010 IB,HA-KIT (ARG)<HA>
1 8A-NFJ-901-010 IB,H(ECA)M<HT>
1 8A-NFJ-932-010 IB,LH-KIT (BRA)<LH>
2 8Z-NF8-702-010 RC UNIT,RC-ZAS01
3 87-006-225-010 ANT,LOOP ANT NC2<HA,LH>

3 87-006-226-010 ANT,LOOP AM<HT>

3 87-006-269-010 ANT,LOOP AM<HT>
4 87-043-115-010 FEEDER-ANT,FM
5 87-A90-119-010 ANT,WIRE SW(5M)<HT>
! 6 87-A91-017-010 PLUG,CONVERSION JT-0476<HT>

2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the CAUTION
instructions below when servicing. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
WARNING! radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que
FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL radiations.
PICK-UP BLOCK.
ADVARSEL!
Caution: Invisible laser radiation when
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
open and interlocks defeated avoid expo-
af funktion. Undgå udsættelse for stråling.
sure to beam.
Advarsel:Usynling laserståling ved åbning,
This Compact Disc player is classified as a CLASS 1 LASER
når sikkerhedsafbrydere er ude af funktion.
product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit- CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
tävälle näkymättömälle lasersäteilylle. LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling ZA3/ZA4 (KSS-213F) MODEL
laserstrålning, som överskrider gränsen för laserklass 1.

Precaution to replace Optical block

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in

the figure below.

ZA8/ZD8 MODEL

Solder

3
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that D101
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the 3 4
positive (+) side (+VH) of C101. (For two seconds) C101 C102
4 Contact the same end of the discharging resistor as step 3
to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope. 2 2

Select a discharging resistor referring to the following table.

Charging voltage (V) Discharging
Rated power (W) Parts number
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.

4
 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.

R
TE
FRONT C.B
PU
M
CO
RO

18 15 VSS
IC

15
M

C113 MICRO-
COMPUTER
18 VDD
C113
FRONT C.B
Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

5
ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
IC C0010 87-012-368-080 C-CAP,S 0.1-50 Z F
C0011 87-012-368-080 C-CAP,S 0.1-50 Z F
87-020-454-010 IC,DN6851 C0012 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A21-417-010 IC,STK490-310 C0015 87-012-368-080 C-CAP,S 0.1-50 Z F
8A-NF8-613-010 C-IC,LC866548V-5P87<HA> C0016 87-012-368-080 C-CAP,S 0.1-50 Z F
8A-NF8-620-010 C-IC,LC866548V-5R49<HT,LH>
87-A21-396-010 IC,STK490-040 C0017 87-012-368-080 C-CAP,S 0.1-50 Z F
C0018 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A21-629-010 IC,SPS-442-1-N C0019 87-016-520-000 CAP,E 3300-65 M SMG
87-A21-419-040 C-IC,NJM14558MD-TE2 C0020 87-016-520-000 CAP,E 3300-65 M SMG
87-A21-577-040 C-IC,M61506FP C0021 87-016-051-000 CAP,E 2200-35 M SMG
87-070-289-040 C-IC,BU2092F
87-A21-401-040 C-IC,M61503FP C0022 87-016-051-000 CAP,E 2200-35 M SMG
C0023 87-016-658-000 CAP,E 4700-35 M SMG
87-A21-560-010 IC,LA1844L-A C0024 87-016-658-000 CAP,E 4700-35 M SMG
87-070-127-110 IC,LC72131D C0025 87-010-408-080 CAP,E 47-50 M 11L SME
C0026 87-010-247-080 CAP,E 100-50 M SME
TRANSISTOR C0030 87-010-430-080 CAP,E 100-63
C0031 87-010-263-080 CAP,E 100-10 M 11L SME
87-026-451-080 TR,2SA933S C0032 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-026-609-080 TR,KTA1266GR C0034 87-010-260-080 CAP,E 47-25 M 11L SME
89-213-702-010 TR,2SB1370E C0035 87-010-380-080 CAP,E 47-16 M 11L SME
87-026-610-080 TR,KTC3198GR
87-A30-076-080 C-TR,2SC3052F C0036 87-010-381-080 CAP,E 330-16 M SME
C0038 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A30-075-080 C-TR,2SA1235F C0060 87-010-403-080 CAP,E 3.3-50 M 11L SME
87-026-245-080 TR,DTC114ES C0061 87-010-260-080 CAP,E 47-25 M 11L SME
87-A30-198-080 TR,KTC3199GR C0101 87-010-183-080 C-CAP,S 2700P-50 K B GRM
87-A30-107-070 C-TR,CMBT5401
87-A30-106-040 C-TR,CMBT5551 C0102 87-010-183-080 C-CAP,S 2700P-50 K B GRM
C0103 87-010-545-080 CAP,E 0.22-50 M 11L SME
87-A30-087-080 C-FET,2SK2158 C0104 87-010-545-080 CAP,E 0.22-50 M 11L SME
87-A30-074-080 C-TR,RT1P 141C C0107 87-010-405-080 CAP,E 10-50 M 11L SME
87-A30-495-080 TR,2SA1981Y C0108 87-010-405-080 CAP,E 10-50 M 11L SME
87-A30-091-080 FET,2SJ460
87-A30-329-080 TR,CD1585BC C0109 87-010-179-080 C-CAP,S 1200P-50 K B GRM
C0110 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-A30-090-080 FET,2SK2541 C0111 87-010-405-080 CAP,E 10-50 M 11L SME
87-A30-104-080 C-TR,RT1N 441C C0112 87-010-405-080 CAP,E 10-50 M 11L SME
87-A30-468-080 C-TR,KRC102S-RTK C0113 87-010-866-080 CAP,E 10-63 M VX
87-A30-484-080 C-TR,KRA102S
87-A30-492-080 TR,2SC5343G<HT,LH> C0114 87-010-866-080 CAP,E 10-63 M VX
C0119 87-010-197-080 C-CAP,S 0.01-25 K B C2012
89-333-317-880 TR,2SC3331(T/U)<HA> C0120 87-010-197-080 C-CAP,S 0.01-25 K B C2012
87-A30-269-040 C-FET,2SJ461-T1 C0125 87-012-368-080 C-CAP,S 0.1-50 Z F
89-327-143-080 C-TR,2SC2714O C0126 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A30-489-080 C-TR,KRA107S
87-A30-072-080 C-TR,RT1P 144C<HT> C0127 87-012-368-080 C-CAP,S 0.1-50 Z F
C0128 87-012-368-080 C-CAP,S 0.1-50 Z F
87-A30-086-040 C-TR,CSD1306E<HT> C0133 87-010-186-080 C-CAP,S 4700P-50 K B C2012
89-503-602-080 C-FET,2SK360E<HT> C0140 87-010-182-080 C-CAP,S 2200P-50 K B C2012
87-A30-234-080 TR,CSC4115BC C0141 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

C0203 87-010-182-080 C-CAP,S 2200P-50 K B C2012

DIODE C0204 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0205 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-A40-393-090 DIODE,1N5402GW(F20) C0206 87-010-179-080 C-CAP,S 1200P-50 K B GRM
87-020-465-080 DIODE,1SS133 C0209 87-010-402-080 CAP,E 2.2-50 M 11L SME
87-A40-547-090 DIODE,D5SBA20
87-A40-455-080 DIODE,RL203 GW C0210 87-010-402-080 CAP,E 2.2-50 M 11L SME
87-A40-553-080 DIODE,1N4003 LES C0211 87-010-184-080 C-CAP,S 3300P-50 K B C2012
C0212 87-010-184-080 C-CAP,S 3300P-50 K B C2012
87-A40-776-080 ZENER,UZ27BSD C0213 87-010-402-080 CAP,E 2.2-50 M 11L SME
87-A40-764-080 ZENER,UZ10BSC C0214 87-010-402-080 CAP,E 2.2-50 M 11L SME
87-A40-270-080 C-DIODE,MC2838
87-A40-313-080 C-DIODE,MC2840 C0217 87-010-405-080 CAP,E 10-50 M 11L SME
87-A40-269-080 C-DIODE,MC2836 C0218 87-010-405-080 CAP,E 10-50 M 11L SME
C0220 87-010-405-080 CAP,E 10-50 M 11L SME
87-A40-768-080 ZENER,UZ16BSA C0223 87-010-190-080 C-CAP,S 0.01-50 Z F C2012
87-A40-752-080 ZENER,UZ6.2BSC C0224 87-010-190-080 C-CAP,S 0.01-50 Z F C2012
87-A40-802-080 ZENER,UZ5.1BSC
87-A40-739-080 ZENER,UZ2.7BSA C0228 87-010-405-080 CAP,E 10-50 M 11L SME
87-017-149-080 ZENER,HZS6A2L C0229 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0230 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0231 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
MAIN C.B C0232 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0003 87-012-368-080 C-CAP,S 0.1-50 Z F C0239 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0004 87-012-368-080 C-CAP,S 0.1-50 Z F C0301 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0005 87-012-368-080 C-CAP,S 0.1-50 Z F C0302 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0006 87-012-368-080 C-CAP,S 0.1-50 Z F C0303 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0009 87-012-368-080 C-CAP,S 0.1-50 Z F C0304 87-010-178-080 C-CAP,S 1000P-50 K B C2012

6
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
C0307 87-010-263-080 CAP,E 100-10 M 11L SME C0632 87-010-185-080 C-CAP,S 3900P-50 K B
C0308 87-010-263-080 CAP,E 100-10 M 11L SME C0633 87-016-369-080 C-CAP,S 0.033-25 K B GRM
C0309 87-010-318-080 C-CAP,S 47P-50 J CH GRM C0634 87-016-369-080 C-CAP,S 0.033-25 K B GRM
C0310 87-010-318-080 C-CAP,S 47P-50 J CH GRM C0661 87-010-178-080 C-CAP,S 1000P-50 K B C2012
C0313 87-010-188-080 C-CAP,S 6800P-50 K B C2012 C0662 87-010-178-080 C-CAP,S 1000P-50 K B C2012

C0314 87-010-188-080 C-CAP,S 6800P-50 K B C2012 C0671 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0315 87-010-263-080 CAP,E 100-10 M 11L SME C0672 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0317 87-010-546-080 CAP,E 0.33-50 M 11L SME C0673 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C0318 87-010-546-080 CAP,E 0.33-50 M 11L SME C0677 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0326 87-010-198-080 C-CAP,S 0.022-25 K B C2012 C0771 87-010-263-080 CAP,E 100-10 M 11L SME

C0327 87-012-368-080 C-CAP,S 0.1-50 Z F C0772 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0360 87-010-401-080 CAP,E 1-50 M 11L SME C0782 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0399 87-012-140-080 C-CAP,S 470P-50 J CH C0783 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0401 87-010-544-080 CAP,E 0.1-50 M 11L SME C0784 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0402 87-010-544-080 CAP,E 0.1-50 M 11L SME C0785 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0403 87-010-321-080 C-CAP,S 82P-50 J CH C0786 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0404 87-010-321-080 C-CAP,S 82P-50 J CH C0788 87-010-149-080 C-CAP,S 5P-50 C CH GRM
C0405 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0789 87-A10-801-080 C-CAP,S 0.022-16 J B CM<HT>
C0406 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0789 87-A12-052-080 C-CAP,S 0.033-25 J B<HA,LH>
C0407 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0790 87-A10-801-080 C-CAP,S 0.022-16 J B CM<HT>

C0408 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0790 87-A12-052-080 C-CAP,S 0.033-25 J B<HA,LH>
C0409 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0791 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0410 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0792 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0411 87-010-405-080 CAP,E 10-50 M 11L SME C0793 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0412 87-010-405-080 CAP,E 10-50 M 11L SME C0795 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0452 87-010-382-080 CAP,E 22-25 M 11L SME C0796 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0453 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0797 87-010-405-080 CAP,E 10-50 M 11L SME
C0454 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0798 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0455 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0799 87-010-407-080 CAP,E 33-50 M 11L SME
C0456 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0800 87-012-369-080 C-CAP,S 0.047-50 Z F

C0457 87-A12-361-080 CAP,M 5600P-100 J CP<HT,LH> C0801 87-010-403-080 CAP,E 3.3-50 M 11L SME
C0458 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0802 87-010-194-080 C-CAP,S 0.047-25 Z F
C0459 87-010-175-080 C-CAP,S 560P-50 J SL C0803 87-010-198-080 C-CAP,S 0.022-25 K B C2012
C0460 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0804 87-010-263-080 CAP,E 100-10 M 11L SME
C0461 87-012-158-080 C-CAP,S 390P-50 J CH GRM C0807 87-010-400-080 CAP,E 0.47-50 M 11L SME

C0462 87-012-158-080 C-CAP,S 390P-50 J CH GRM C0808 87-010-401-080 CAP,E 1-50 M 11L SME
C0507 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0809 87-010-401-080 CAP,E 1-50 M 11L SME
C0508 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0810 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0509 87-A10-300-080 CAP,M 0.027-50 J<HA> C0814 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0509 87-A12-369-080 CAP,M 0.027-100 J CP<HT,LH> C0815 87-010-400-080 CAP,E 0.47-50 M 11L SME

C0510 87-A10-300-080 CAP,M 0.027-50 J<HA> C0816 87-010-400-080 CAP,E 0.47-50 M 11L SME
C0510 87-A12-369-080 CAP,M 0.027-100 J CP<HT,LH> C0821 87-010-405-080 CAP,E 10-50 M 11L SME
C0515 87-A10-300-080 CAP,M 0.027-50 J<HA> C0823 87-010-177-080 C-CAP,S 820P-50 J SL C2012
C0515 87-A12-369-080 CAP,M 0.027-100 J CP<HT,LH> C0824 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0516 87-A10-300-080 CAP,M 0.027-50 J<HA> C0825 87-010-596-080 C-CAP,S 0.047-16 K R C2012

C0516 87-A12-369-080 CAP,M 0.027-100 J CP<HT,LH> C0842 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0518 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0844 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0519 87-010-401-080 CAP,E 1-50 M 11L SME C0850 87-010-260-080 CAP,E 47-25 M 11L SME
C0520 87-010-401-080 CAP,E 1-50 M 11L SME C0851 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0521 87-010-546-080 CAP,E 0.33-50 M 11L SME C0852 87-010-197-080 C-CAP,S 0.01-25 K B C2012

C0522 87-010-546-080 CAP,E 0.33-50 M 11L SME C0853 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0523 87-010-545-080 CAP,E 0.22-50 M 11L SME C0858 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0524 87-010-545-080 CAP,E 0.22-50 M 11L SME C0859 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0525 87-010-545-080 CAP,E 0.22-50 M 11L SME C0860 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0526 87-010-545-080 CAP,E 0.22-50 M 11L SME C0940 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT>

C0605 87-010-179-080 C-CAP,S 1200P-50 K B GRM C0941 87-010-314-080 C-CAP,S 22P-50 J CH GRM<HT>
C0606 87-010-179-080 C-CAP,S 1200P-50 K B GRM C0943 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT>
C0609 87-010-213-080 C-CAP,S 0.015-25 K B GRM C0945 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT>
C0610 87-010-213-080 C-CAP,S 0.015-25 K B GRM C0946 87-010-971-080 C-CAP,S 4700P-50 J B<HT>
C0611 87-010-545-080 CAP,E 0.22-50 M 11L SME C0947 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT>

C0612 87-010-545-080 CAP,E 0.22-50 M 11L SME C0948 87-010-148-080 C-CAP,S 4P-50 C CH GRM<HT>
C0613 87-010-545-080 CAP,E 0.22-50 M 11L SME C0952 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT>
C0614 87-010-545-080 CAP,E 0.22-50 M 11L SME C0953 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT>
C0615 87-010-154-080 C-CAP,S 10P-50 D CH GRM C0954 87-010-400-080 CAP,E 0.47-50 M 11L SME<HT>
C0616 87-010-385-080 CAP,E 220-25 M SME C0956 87-010-263-080 CAP,E 100-10 M 11L SME<HT>

C0617 87-010-385-080 CAP,E 220-25 M SME C0959 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0618 87-010-405-080 CAP,E 10-50 M 11L SME C0960 87-010-196-080 C-CAP,S 0.1-25 Z F C2012<HA,LH>
C0620 87-010-263-080 CAP,E 100-10 M 11L SME C0961 87-010-152-080 C-CAP,S 8P-50 D CH GRM<HA,LH>
C0630 87-016-669-080 C-CAP,S 0.1-25 K B C0962 87-010-401-080 CAP,E 1-50 M 11L SME<HT>
C0631 87-010-185-080 C-CAP,S 3900P-50 K B C0963 87-015-785-080 C-CAP, 0.1-25 Z F C3216

7
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
C0964 87-010-854-080 C-CAP,S 560P-50 J CH<HT> WH0001 87-A91-179-010 HLDR,WIRE 2.5-11P
C0971 87-010-381-080 CAP,E 330-16 M SME X0991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
C0972 87-010-404-080 CAP,E 4.7-50 M 11L SME
C0973 87-010-197-080 C-CAP,S 0.01-25 K B C2012
C0974 87-010-197-080 C-CAP,S 0.01-25 K B C2012 FRONT C.B

C0979 87-010-322-080 C-CAP,S 100P-50 J CH GRM C0201 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0981 87-010-260-080 CAP,E 47-25 M 11L SME C0202 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0982 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0203 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0983 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0204 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0984 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0205 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C0987 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0206 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0989 87-010-197-080 C-CAP,S 0.01-25 K B C2012<HT> C0207 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0991 87-010-312-080 C-CAP,S 15P-50 J CH GRM C0208 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0992 87-010-312-080 C-CAP,S 15P-50 J CH GRM C0209 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0993 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0210 87-010-322-080 C-CAP,S 100P-50 J CH GRM

C0995 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0211 87-010-322-080 C-CAP,S 100P-50 J CH GRM
C0997 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0251 87-010-405-040 CAP,E 10-50 M 11L SME
C0998 87-010-260-080 CAP,E 47-25 M 11L SME C0253 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
C0999 87-A11-132-080 CAP,TC U 0.01-50 K B C0254 87-012-369-080 C-CAP,S 0.047-50 Z F
CF0831 87-008-261-010 FLTR,CF SFE10.7MA5 C0255 87-010-560-040 CAP,E 10-50 M 5L MA

CF0832 87-008-261-010 FLTR,CF SFE10.7MA5 C0256 87-010-405-040 CAP,E 10-50 M 11L SME
CN0301 87-A60-620-010 CONN,3P V 2MM JMT C0259 87-010-405-040 CAP,E 10-50 M 11L SME
CN0351 87-A60-625-010 CONN,8P V 2MM JMT C0264 87-A11-148-080 CAP,TC U 0.1-50 Z F
CN0601 87-099-719-010 CONN,30P H BLK TYK-B(X) C0273 87-010-178-080 C-CAP,S 1000P-50 K B C2012
CN0602 87-A60-131-010 CONN,6P V FE C0274 87-010-178-080 C-CAP,S 1000P-50 K B C2012

CNA0001 8A-NF8-654-010 CONN ASSY,11P TID-A(480) C0301 87-010-182-080 C-CAP,S 2200P-50 K B C2012
D0951 87-A40-618-080 VARI-CAP,SVC 348(S/T)<HT> C0302 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
FFC602 88-906-251-110 FF-CABLE,6P 1.25 C0303 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
FFE0831 A8-8ZA-190-030 8ZA-1 FEUNM<HT> C0312 87-010-498-040 CAP,E 10-16 M 5L SRE
FFE0831 A8-8ZA-191-030 8ZA-1 YFEUNM<HA,LH> C0314 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

J0201 87-A60-483-010 JACK,DIA6.3 BLK ST W/S KM C0315 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
J0203 87-A60-238-010 TERMINAL,SP 4P (MSC) C0316 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
J0204 87-A61-153-010 JACK,PIN 4P R/W(BL) (SEPA) KM<HT> C0321 87-012-393-080 C-CAP,S 0.22-16 K W5R CM/CB
J0205 87-A61-157-010 JACK,PIN 2P R/W/BL V(SEPA) KM<HA,LH> C0322 87-010-400-040 CAP,E 0.47-50 M 11L SME
J0602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN C0325 87-A10-189-040 CAP,E 220-10 M 5L

J0831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02 C0326 87-A10-189-040 CAP,E 220-10 M 5L

J0940 87-A60-633-010 CONN,2P H 2.5MM JMT<HT> C0332 87-010-178-080 C-CAP,S 1000P-50 K B C2012
L0101 87-A50-610-010 COIL,1UH K(MDEC) C0334 87-010-312-080 C-CAP,S 15P-50 J CH GRM
L0102 87-A50-610-010 COIL,1UH K(MDEC) C0335 87-012-140-080 C-CAP,S 470P-50 J CH
L0201 87-A50-610-010 COIL,1UH K(MDEC) C0336 87-012-155-080 C-CAP,S 180P-50 J CH GRM

L0202 87-A50-610-010 COIL,1UH K(MDEC) C0339 87-012-156-080 C-CAP,S 220P-50 J CH GRM

L0451 87-007-342-010 COIL,OSC 85KHZ BIAS C0340 87-010-197-080 C-CAP,S 0.01-25 K B C2012
L0801 87-A50-608-010 COIL,FM DET-N(TOK) C0341 87-010-194-080 C-CAP,S 0.047-25 Z F
L0802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)<HA,LH> C0351 87-010-981-040 CAP,E 22-35 M 5L SRE
L0802 87-A91-552-010 FLTR,CFMT-450AL (TOK)<HT> C0401 87-010-197-080 C-CAP,S 0.01-25 K B C2012

L0811 87-005-847-080 COIL,2.2UH K CECS C0451 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

L0832 87-005-847-080 COIL,2.2UH K CECS C0452 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
L0941 87-A50-022-010 COIL,ANT SW (COI) 7.96MHZ<HT> C0453 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
L0942 87-A50-550-010 COIL,OSC SW-2N(COI)<HT> C0454 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
L0943 87-A50-522-080 COIL,1MH K CEC<HT> C0455 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

L0944 87-A50-159-010 COIL,10MH K C2B<HT> C0458 87-010-320-080 C-CAP,S 68P-50 J CH GRM

L0951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<HA,LH> C0459 87-010-320-080 C-CAP,S 68P-50 J CH GRM
L0952 87-A50-430-010 COIL,ANT MW(3BSW)<HT> C0502 87-010-186-080 C-CAP,S 4700P-50 K B C2012
L0953 87-A50-431-010 COIL,OSC MW(3BSW)<HT> C0503 87-010-112-040 CAP,E 100-16 M 11L SME
R0129 87-A00-257-080 RES,M/F 0.15-1W J C0504 87-010-405-040 CAP,E 10-50 M 11L SME

R0130 87-A00-257-080 RES,M/F 0.15-1W J C0505 87-010-545-040 CAP,E 0.22-50 M 11L SME
R0143 87-A00-440-050 RES,220-1/2W J RP C0506 87-010-320-080 C-CAP,S 68P-50 J CH GRM
R0144 87-A00-440-050 RES,220-1/2W J RP C0507 87-010-544-040 CAP,E 0.1-50 M 11L SME
R0145 87-A00-440-050 RES,220-1/2W J RP C0508 87-010-544-040 CAP,E 0.1-50 M 11L SME
R0146 87-A00-440-050 RES,220-1/2W J RP C0510 87-010-322-080 C-CAP,S 100P-50 J CH GRM

R0233 87-A00-258-080 RES,M/F 0.22-1W J C0511 87-010-265-040 CAP,E 33-16 M 11L SME
R0234 87-A00-258-080 RES,M/F 0.22-1W J C0512 87-010-178-080 C-CAP,S 1000P-50 K B C2012
R0790 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0513 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
R0991 87-010-322-080 C-CAP,S 100P-50 J CH GRM C0515 87-010-178-080 C-CAP,S 1000P-50 K B C2012
R0993 87-010-322-080 C-CAP,S 100P-50 J CH GRM C0520 87-010-178-080 C-CAP,S 1000P-50 K B C2012

R0995 87-010-322-080 C-CAP,S 100P-50 J CH GRM C0602 87-010-322-080 C-CAP,S 100P-50 J CH GRM
SFR0451 87-A90-432-080 SFR,30K H NVZ6TLTA C0603 87-010-322-080 C-CAP,S 100P-50 J CH GRM
SFR0452 87-A90-432-080 SFR,30K H NVZ6TLTA C0604 87-010-322-080 C-CAP,S 100P-50 J CH GRM
TC0941 87-011-254-080 TRIMMER,CER 20P 4.0X4.5 ECR<HT> C0650 87-010-196-080 C-CAP,S 0.1-25 Z F C2012
TC0943 87-011-253-080 TRIMMER,CER 30P 4.0X4.5 ECRLA<HT> C0699 87-010-196-080 C-CAP,S 0.1-25 Z F C2012

8
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
CN0101 87-099-720-010 CONN,30P BLK TYK-B(P) S0436 87-A91-024-180 SW,TACT KSHG611BT
CN0102 87-099-015-010 CONN,13P V BLK 6216 S0437 87-A91-024-180 SW,TACT KSHG611BT
CN0301 87-A60-140-010 CONN,15P V FE SW0252 87-A91-555-010 SW,RTRY EC12E24504
FB0301 87-008-372-080 FLTR,EMI BL01 RN1 SW0253 87-A91-542-010 SW,RTRY EC12E12504
FB0501 87-008-372-080 FLTR,EMI BL01 RN1 VR0501 86-NFA-607-010 VR,RTRY 10K15AX1 1 V XV0121PVN

FFC102 88-913-301-110 FF-CABLE,13P-1.25

FFC105 88-915-101-110 FF-CABLE, 15P 1.25 100MM DECK C.B
FL0401 8A-NF8-601-010 FL,HNA-11MM30(ANF-8)
J0501 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM<HA> CON105 87-099-756-010 CONN,15P 9604 S F
J0501 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC<HT,LH> SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY,27
L0331 87-A50-408-010 COIL,OSC 5.76MHZ SOL2 82-ZM1-618-410 SOL ASSY,27
LED0311 87-A40-589-040 LED,SLR-56VCT31 RED SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ
LED0601 87-A40-803-010 LED,SELU1E10CXM-S LF38 BLUE
LED0602 87-A40-619-080 LED,SLR-56PT-TE7-W GRN SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ
LED0603 87-A40-619-080 LED,SLR-56PT-TE7-W GRN SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW4 87-036-110-010 SW,MICRO SPPB62
LED0604 87-A40-619-080 LED,SLR-56PT-TE7-W GRN SW5 87-036-110-010 SW,MICRO SPPB62
LED0606 87-A40-619-080 LED,SLR-56PT-TE7-W GRN SW6 87-036-110-010 SW,MICRO SPPB62
LED0607 87-A40-619-080 LED,SLR-56PT-TE7-W GRN
LED0608 87-A40-619-080 LED,SLR-56PT-TE7-W GRN SW8 87-A90-248-010 SW,MICRO ESE11SH2CXQ
S0401 87-A91-024-180 SW,TACT KSHG611BT SW9 87-A90-248-010 SW,MICRO ESE11SH2CXQ
W1 82-ZM3-601-010 RBN,CORD,4P-75
S0402 87-A91-024-180 SW,TACT KSHG611BT
S0403 87-A91-024-180 SW,TACT KSHG611BT
S0404 87-A91-024-180 SW,TACT KSHG611BT HEAD-1 C.B
S0405 87-A91-024-180 SW,TACT KSHG611BT
S0406 87-A91-024-180 SW,TACT KSHG611BT 85-ZM3-602-010 PWB,FLEX A
CON301 87-NF6-615-010 CONN ASSY,3P PB
S0407 87-A91-024-180 SW,TACT KSHG611BT
S0408 87-A91-024-180 SW,TACT KSHG611BT
S0409 87-A91-024-180 SW,TACT KSHG611BT HEAD-2 C.B
S0410 87-A91-024-180 SW,TACT KSHG611BT
S0411 87-A91-024-180 SW,TACT KSHG611BT 85-ZM3-602-010 PWB,FLEX A
CON351 87-NF6-616-010 CONN ASSY,8P-RPB
S0412 87-A91-024-180 SW,TACT KSHG611BT
S0413 87-A91-024-180 SW,TACT KSHG611BT
S0414 87-A91-024-180 SW,TACT KSHG611BT PT C.B
S0415 87-A91-024-180 SW,TACT KSHG611BT
S0416 87-A91-024-180 SW,TACT KSHG611BT C0001 87-010-387-080 CAP,E 470-25 M SME
C0031 87-010-403-040 CAP,E 3.3-50 M 11L SME
S0417 87-A91-024-180 SW,TACT KSHG611BT CN0001 87-A61-122-010 CONN,11P V TID-A
S0418 87-A91-024-180 SW,TACT KSHG611BT !PT0001 8A-NF8-605-010 PT,ANF-8 LH
S0419 87-A91-024-180 SW,TACT KSHG611BT !PT0002 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI
S0420 87-A91-024-180 SW,TACT KSHG611BT
S0425 87-A91-024-180 SW,TACT KSHG611BT !RY0001 87-A91-339-010 RELAY,AC DC12V G5PA-2
!S0001 87-A90-165-010 SW,SL 1-2-3 SWS2301
S0426 87-A91-024-180 SW,TACT KSHG611BT !T0001 87-A60-317-010 TERMINAL, 1P MSC
S0432 87-A91-024-180 SW,TACT KSHG611BT !T0002 87-A60-317-010 TERMINAL, 1P MSC
S0433 87-A91-024-180 SW,TACT KSHG611BT
S0434 87-A91-024-180 SW,TACT KSHG611BT
S0435 87-A91-024-180 SW,TACT KSHG611BT

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

9
TRANSISTOR ILLUSTRATION

B
E
ECB ECB BCE
2SA1981 2SA933S 2SB1370 2SA1235
2SC3331 DTC114ES 2SC2714
2SC5343 KTC3199 2SC3052
CD1585 CMBT5401
CSC4115 CMBT5551
KTA1266 CSD1306
KTC3198 KRA102S
KRA107S
KRC102S
RT1N441C
D S RT1P141C
RT1P144C

G D
S G
SDG
2SJ460 2SJ461 2SK360
2SK2541 2SK2158

10
FL (HNA-11MM30) GRID ASSIGNMENT/ANODE CONNECTION

GRID ASSIGNMENT

ANODE CONNECTION

11 12
WIRING-1 (MAIN C.B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

13 14
SCHEMATIC DIAGRAM-1 (FUNCTION/AMP SECTION)

15 16
SCHEMATIC DIAGRAM-2 (TUNER SECTION) <HA, LH>

17 18
SCHEMATIC DIAGRAM-3 (TUNER SECTION) <HT>

19 20
WIRING-2 (FRONT C.B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

21 22
SCHEMATIC DIAGRAM-4 (FRONT SECTION)

23 24
SCHEMATIC DIAGRAM-5 (PT SECTION) WIRING-3 (PT C.B)
1 2 3 4 5 6 7

25 26
WIRING-4 (DECK C.B)
1 2 3 4 5 6 7

27
IC BLOCK DIAGRAM
IC, LA1844

IC, LC72131D

28
IC, M61506FP IC, BU2092F

IC, M61503FP

29
IC DESCRIPTION
IC, LC866548V-5P87 <HA>, LC866548V-5P49 <HT,LH>
Pin No. Pin Name I/O Description
_______________
1 I-STEREO/I-DRF I Stereo detected input/CD DRF input
______
2 I-IFC/I-SUBQ I Tune IF count serial data input/CD SUBQ input
3 O-2PB O Deck 2 playback switch output
_______
4 O-POWER O System power supply ON/OFF output
_______
5 O-CD-ON O CD power ON/OFF output
6 O-PLL_DATA O LED driver, Tuner IC, Function IC data output
7 O-RMT O Deck 2 REC MUTE output
_________ _____
8 O-BIAS O Deck 2 bias ON/OFF output
_______
9 O-MUTE O System mute ON/OFF output
10 O-STB O Latch strobe output for LED driver IC
_________________
11 O-CLK_SFT O Micon clock shift output
12 RESET I System reset
13 NC – Not connected
14 I-DISH I CD turntable photo sensor A/D converter input
15 VSS1 – GND
16 CF1 – 5.76 MHz oscillator circuit
17 CF2 – 5.76 MHz oscillator circuit
18 VDD1 – Power supply input
__________
19 I-HOLD I Power failure detected input
20 I-KEY1 I KEY input (A/D)
21 I-KEY2 I KEY input (A/D)
22 I-KEY3 I KEY input (A/D)
23 I-TU_SIG I Tuner signal input
24 I-CDSW I CD mechanical switch A/D converter input
25 I-SPEANA I A/D input for spectrum analyzer display
26 I-RE_VOL I Rotary encoder input (VOL)
27 I-WRQ/I-RDS_CLK I CD WRQ input/Tuner RDS clock input
28 I-TM_BASE I Reference clock input for timer watch
_________
29 I-RMC I System remotecontrol signal input
30 ~ 40 G11 ~ G1 O FL GRID output G11 ~ G1
41 NC – Not connected
42 ~ 45 P35 ~ P32 O FL SEGMENT output P35 ~ P32
46 VDD3 – Power supply input
47 ~ 48 P31 ~ P30 O FL SEGMENT output P31 ~ P30
49 P29/O-SPEANA-C O FL SEGMENT output P29/Spectrum analyzer band switching output
50 P28/O-SPEANA-B O FL SEGMENT output P28/Spectrum analyzer band switching output
51 VFL – Power supply input for FL display
52 P27/O-SPEANA-A O FL SEGMENT output P27/Spectrum analyzer band switch output
53 P26 O FL SEGMENT output P26
54 P25/I-NO_CASINO I/O FL SEGMENT output P25/NO CASINO DEMO input to diode
55 P24/I-KARAOKE I/O FL SEGMENT output P24/KARAOKE input to diode
56 P23/NO_DEMO I/O FL SEGMENT output P23/NO DEMO input to diode

30
Pin No. Pin Name I/O Description

57 P22/PRO LOGIC I/O FL SEGMENT output P22/PROLOGIC input to diode (not used)
58 P21/RDS I/O FL SEGMENT output P21/RDS input to diode
59 P20/FM1 I/O FL SEGMENT output P20/FM1 input to diode
60 P19/SW I/O FL SEGMENT output P19/SW input to diode
61 P18/LW I/O FL SEGMENT output P18/LW input to diode
62 P17/AMST I/O FL SEGMENT output P17/AMST input to diode
63 P16/AM10K I/O FL SEGMENT output P16/AM10K input to diode
_________
64 P15/I-CST2 I/O FL SEGMENT output P15/DECK2 cassette detect switch data input
________
65 P14/I-REB I/O FL SEGMENT output P14/DECK2 side-B record OK switch data input
___________
66 P13/I-CAM2 I/O FL SEGMENT output P13/DECK2 CAM switch signal input
____________
67 P12/I-AUTO1 I/O FL SEGMENT output P12/DECK1 AUTO STOP signal input
_____________
68 P11/I-AUTO2 I/O FL SEGMENT output P11/DECK2 AUTO STOP signal input
__________
69 P10/I-CAM1 I/O FL SEGMENT output P10/DECK1 CAM switch data input
_________
70 P9/I-CST1 I/O FL SEGMENT output P9/DECK1 cassette detect switch data input
________
71 P8/I-REA I/O FL SEGMENT output P8/DECK2 side A record OK switch data input
72 VDD4 – Power supply input
73 P7/I-REV2 I/O FL SEGMENT output P7/DECK2 REVERSE mode input to diode
74 P6/I-REV1 I/O FL SEGMENT output P6/DECK1 REVERSE mode input to diode
75 P5/NO_ECO I/O FL SEGMENT output P5/NO ECO MODE input to diode
76 ~ 79 P4 ~ P1 O FL SEGMENT output P4 ~ P1
80 O-CD CLOSE O CD TRAY CLOSE data output
81 O-CD OPEN O CD TRAY OPEN data output
82 NC – Not connected
83 I-JOG_A I Rotary encoder A input (JOG)
84 I-JOG_B I Rotary encoder B input (JOG)
85 O-DISH_FWD O CD turntable forward rotation output
86 O-DISH_REV O CD turntble reverse rotation output
87 O-PLL_CE O PLL IC chip enable output
_____________
88 O-KSCAN O Switch SCAN timing output
89 VSS2 – GND
90 VDD2 – Power supply input
_________
91 LED-STBY O STAND BY LED (Echo mode) ouput
______________ _____
92 O-MOTOR O DECK MOTOR ON/OFF output
_________
93 O-SOL1 O DECK1 soleroid ouput
_________
94 O-SOL2 O DECK2 soleroid ouput
95 O-CD-DATA O CD DATA output
96 O-CD-LED O CD LED output
97 O-CD CLK O CD clock output
98 O-CD CE O CD chip enable output
99 I-RDS_DATA I RDS data input
100 O-PLL_CLK O PLL IC CLOCK output

31
ADJUSTMENT <HA,LH>

MAIN C.B 7 6 1 7

L802
12 L801
IC801 TP4 (DC BALANCE)
SFR451 SFR452
TP3 (DC BALANCE)
L951
TP2 (CLK)
4
TP8 (RCH) (3/3) (1/3)
GND
TP9 (LCH) TP1 (VT) 2
3
FFE831

4 9
5 10
6 11
7 12
8 13

DECK-1 P HEAD
DECK-2 R/P/E HEAD
DECK C.B
SFR1

8 9 9
REV FWD

14
FRONT C.B

FL401 TP7
R268
C326

30
+
IC201
L331
GND 1

14

32
< TUNER SECTION > 10. PB Frequency Response Check (DECK 1, DECK 2)
1. Clock frequency Check Settings : • Test tape : TTA–300
Settings : • Test point : TP2 • Test point :TP8(Lch), TP9(Rch)
Method : Set to AM 1710kHz and check that the test point is Method : Play back the 315Hz and 8kHz signals of the test
2160kHz ± 45Hz. tape and check that the output ratio of the 8kHz
signal with respect to that of the 315Hz signal is
2. AM VT Check within 5dB.
Settings : • Test point : TP1 (VT)
Method : Set to AM 1710kHz, 530kHz and check that the test 11. PB Sensitivity Check (DECK 1, DECK 2)
point is less than 8.5V (1710kHz) and more than Settings : • Test tape : TTA–200
0.6V (530kHz). • Test point : TP8(Lch), TP9(Rch)
Method : Play back the test tape and check that the output
3. FM VT Check level of the test point is 140mV ± 3dB.
Settings : • Test point : TP1 (VT)
Method : Set to FM 87.5MHz, 108.0MHz and check that the 12. REC/PB Frequency Response Adjustment (DECK 2)
test point is more than 0.5V (87.5MHz) and less Settings : • Test tape : TTA–602
than 8.0V (108.0MHz). • Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz / 8kHz (LINE IN)
4. AM Tracking Adjustment • Adjustment location : SFR451 (Lch)
Settings : • Test point : TP8(Lch), TP9(Rch) SFR452 (Rch)
• Adjustment location : Method : Apply a 1kHz signal and REC mode. Then adjust
L951(1/3) ...................................... 1000kHz OSC attenuator so that the output level at the TP8,
Method : Set to AM 1000kHz and adjust L951(1/3) so that TP9 becomes -20VU. Record and play back the
the level at the test point becomes maximum. 1kHz and 8kHz signals and adjust SFRs so that the
output of the 8kHz signals becomes 0dB ± 0.5dB
5. FM Tracking Check with respect to that of the 1kHz signal.
Settings : • Test point : TP8(Lch), TP9(Rch)
Method : Set to FM 98.0MHz and check that the test point is 13. REC/PB Sensitivity Check (DECK 2)
less than 9dBµV. Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
6. AM IF Adjustment • Input signal : 1kHz (LINE IN)
Settings : • Test point : TP8(Lch), TP9(Rch) Method : Apply a 1kHz signal and REC mode. Then adjust
• Adjustment location : OSC attenuator so that the output level at TP8, TP9
L802 ............................................. 1000kHz becomes 0VU. Record and play back the 1kHz
signals and check that the output is –2dB ± 3.0dB.
7. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance) < FRONT SECTION >
: TP8(Lch), TP9(Rch) (Distortion) 14. µ-CON OSC Adjustment
• Adjustment location : L801 Settings : • Test point : TP7 and GND
• Input level : 60dBµV • Adjustment location : L331
Method : Set to FM 98.0MHz and adjust L801 so that the Method : Insert AC plug while pressing POWER and TUNER
voltage between TP3 and TP4 becomes 0V ± 0.3V. function keys. Adjust L331 so that the frequency at
Next, check that the distortion is less than 1.3%. the test point is 153.84Hz ± 0.15Hz.

< DECK SECTION >

8. Tape Speed Adjustment (DECK 2)
Settings : • Test tape : TTA–100
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz ± 5Hz and ±45Hz
(REV) with respect to forward speed.

9. Head Azimuth Adjustment (DECK 1, DECK 2)

Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape
and adjust screw so that the output becomes
maximum. Next, perform on REV PLAY mode.

33
ADJUSTMENT <HT>

MAIN C.B 9 8 1 9

L802
TC943
14 L801
IC801 TP4 (DC BALANCE)
TC941
SFR451 SFR452 L941
TP3 (DC BALANCE)
6
TP2 (CLK)
5
L942
TP8 (RCH) L953 L952
GND
TP9 (LCH) TP1 (VT) 2 4
3
FFE831

5 11
2
6 12
7 13 3
8 14
9 15
10

DECK-1 P HEAD
DECK-2 R/P/E HEAD
DECK C.B
SFR1

10 11 11
REV FWD

16
FRONT C.B

FL401 TP7
R268
C326

30
+
IC201
L331
GND 1

16

34
< TUNER SECTION > < DECK SECTION >
1. Clock frequency Check 10. Tape Speed Adjustment (DECK 2)
Settings : • Test point : TP2 Settings : • Test tape : TTA–100
Method : Set to WM 1602kHz and check that the test point is • Test point : TP8(Lch), TP9(Rch)
2052kHz ± 45Hz. • Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
2. MW VT Adjustment frequency counter reads 3000Hz ± 5Hz and ±45Hz
Settings : • Test point : TP1 (VT) (REV) with respect to forward speed.
• Adjustment location : L953
Method : Set to MW 1710kHz, 530kHz and adjust L953 so 11. Head Azimuth Adjustment (DECK 1, DECK 2)
that the test point is less than 8.5V (1710kHz) and Settings : • Test tape : TTA–330
more than 0.6V (530kHz). • Test point : TP8(Lch), TP9(Rch)
• Adjustment location : Head azimuth
3. SW VT Adjustment adjustment screw
Settings : • Test point : TP1 (VT) Method : Play back (FWD) the 8kHz signal of the test tape
• Adjustment location : L942 and adjust screw so that the output becomes
Method : Set to SW 17.9MHz, 5.73MHz and adjust L942 so maximum. Next, perform on REV PLAY mode.
that the test point is 8.0V ± 0.05V (17.9MHz) and
more than 0.3V (5.9MHz). 12. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–300
4. FM VT Check • Test point :TP8(Lch), TP9(Rch)
Settings : • Test point : TP1 (VT) Method : Play back the 315Hz and 8kHz signals of the test
Method : Set to FM 87.5MHz, 108.0MHz and check that the tape and check that the output ratio of the 8kHz
test point is more than 0.5V (87.5MHz) and less signal with respect to that of the 315Hz signal is
than 8.0V (108.0MHz). within 5dB.

5. MW Tracking Adjustment 13. PB Sensitivity Check (DECK 1, DECK 2)

Settings : • Test point : TP8(Lch), TP9(Rch) Settings : • Test tape : TTA–200
• Adjustment location : • Test point : TP8(Lch), TP9(Rch)
L952 ...................................... 603kHz Method : Play back the test tape and check that the output
TC941 ...................................1404khz level of the test point is 140mV ± 3dB.
Method : Set to MW 603kHz and adjust L952 so that the
level at the test point becomes maximum. 14. REC/PB Frequency Response Adjustment (DECK 2)
Next, set to MW 1404kHz and adjust TC941 so Settings : • Test tape : TTA–602
that the level at the test point becomes maximum. • Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz / 8kHz (LINE IN)
6. SW Tracking Adjustment • Adjustment location : SFR451 (Lch)
Settings : • Test point : TP8(Lch), TP9(Rch) SFR452 (Rch)
• Adjustment location : Method : Apply a 1kHz signal and REC mode. Then adjust
L941 ...................................... 5.9MHz OSC attenuator so that the output level at the TP8,
TC943 ...................................17.9Mhz TP9 becomes -20VU. Record and play back the
Method : Set to SW 5.9MHz and adjust L941 so that the level 1kHz and 8kHz signals and adjust SFRs so that the
at the test point becomes maximum. output of the 8kHz signals becomes 0dB ± 0.5dB
Next, set to SW 17.9MHz and adjust TC943 so that with respect to that of the 1kHz signal.
the level at the test point becomes maximum.
15. REC/PB Sensitivity Check (DECK 2)
7. FM Tracking Check Settings : • Test tape : TTA–602
Settings : • Test point : TP8(Lch), TP9(Rch) • Test point : TP8(Lch), TP9(Rch)
Method : Set to FM 98.0MHz and check that the test point is • Input signal : 1kHz (LINE IN)
less than 9dBµV. Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP8, TP9
8. AM IF Adjustment becomes 0VU. Record and play back the 1kHz
Settings : • Test point : TP8(Lch), TP9(Rch) signals and check that the output is –2dB ± 3.0dB.
• Adjustment location :
L802 ............................................. 999kHz < FRONT SECTION >
16. µ-CON OSC Adjustment
9. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP7 and GND
Settings : • Test point : TP3, TP4 (DC Balance) • Adjustment location : L331
: TP8(Lch), TP9(Rch) (Distortion) Method : Insert AC plug while pressing POWER and TUNER
• Adjustment location : L801 function keys. Adjust L331 so that the frequency at
• Input level : 60dBµV the test point is 153.84Hz ± 0.15Hz.
Method : Set to FM 98.0MHz and adjust L801 so that the
voltage between TP3 and TP4 becomes 0V ± 0.3V.
Next, check that the distortion is less than 1.3%.

35
MECHANICAL MAIN PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NFJ-012-010 WINDOW,CASS 1 32 8A-NFJ-027-010 KEY,DISC
2 8A-NFJ-013-010 WINDOW,CASS 2 33 86-NF9-224-010 SPR-C,LOCK
3 8A-NFJ-035-010 BOX,CASS 1H 34 87-NF4-216-010 HLDR,LOCK 1
4 8A-NFJ-036-010 BOX,CASS 2H 35 82-NF5-229-010 PLATE,LOCK(*)
5 82-NF5-218-010 SPR-T,EJECT 1(SIN) 36 87-NF4-217-110 HLDR,LOCK 2

6 82-NF5-219-010 SPR-T,EJECT 2(SIN) 37 8A-NF8-206-010 HLDR,PWB M

7 8A-NFJ-005-010 WINDOW,FR 2 38 87-064-185-010 HLDR,WIRE PVC 0.5
8 8A-NFJ-017-110 KNOB,RTRY JOG<HT,LH> 39 84-ZG1-245-210 CAP,OPTICAL
8 8A-NFJ-017-010 KNOB,RTRY JOG<HA> 40 8A-NF8-072-110 CABI,REAR HASM<HA,LH>
9 8Z-NF6-210-010 DMPR,150 N 40 8A-NF8-076-010 CABI,REAR HR W/O SPEC<HT>

10 8A-NFJ-033-010 CABI,FR H<HA> 41 8A-DB8-209-010 HLDR,PWB PT

10 8A-NFJ-033-110 CABI,FR H<HT,LH> 42 87-NF4-221-010 HLDR,CABLE
11 8A-NFJ-006-010 WINDOW,FR 1H ! 43 87-085-185-010 BUSHING,AC CORD(E) CM-22B
12 8A-NFJ-026-010 KNOB,RTRY MIC ! 44 87-A80-105-010 AC CORD ASSY,AZ<HA>
13 8A-NFJ-042-010 WINDOW,DISP 54E<HA> ! 44 87-A80-157-010 AC CORD ASSY,E BLK CC<HT,LH>

13 8A-NFJ-043-010 WINDOW,DISP 57<LH> 45 8Z-NB8-240-010 COVER, PL

13 8A-NFJ-039-010 WINDOW,DISP H<HT> 46 8A-NF8-008-010 PANEL,RIGHT V-2
14 8A-NFJ-008-010 WINDOW,CD 47 8A-NF8-205-010 HLDR,IC
15 8A-NF8-007-010 PANEL,LEFT V-2 48 88-906-251-110 FF-CABLE,6P 1.25
16 8A-NF8-005-010 PANEL,TOP 49 87-NF6-615-010 CONN ASSY,3P PB

17 8A-NF8-006-010 WINDOW,TOP 50 87-NF6-616-010 CONN ASSY,8P RPB

18 8A-NFJ-009-010 PANEL,TRAY A 87-067-703-010 BVT2+3-10 W/0 SL0T
19 8A-NFJ-010-010 WINDOW,TRAY B 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
20 88-NF8-205-010 GUIDE,FL C 87-067-581-010 BVT2+3-15 W/0 SL0T
21 8A-NFJ-018-010 KEY,FUN D 87-067-688-010 BVTT+3-6

22 8A-NFJ-016-010 REFLECTOR,FUN E 87-723-096-410 QT2+3-10 W/O SLOT BLK

23 8A-NFJ-014-010 KEY,POWER F 87-067-641-010 UTT2+3-8 W/O SLOT BLK
24 8A-NFJ-015-010 REFLECTOR,ECO G 87-078-191-010 S-SCREW,IT+4-10 SWCH12A
25 8A-NFJ-019-010 KEY,GEQ H 87-721-097-410 QT2+3-12 W/O SLOT
26 8A-NFJ-029-010 KEY,ASSY OPE REV I 87-721-096-410 QT2+3-10 W/O SLOT

27 8A-NF8-203-010 GUIDE,OPE REV

28 8A-NF8-201-010 GUIDE,FUN
29 88-915-101-110 FF-CABLE, 15P 1.25 100MM
30 88-913-301-110 FF-CABLE,13P-1.25
31 8A-NFJ-030-010 KEY,CD EDIT H

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink

36
MECHANICAL EXPLODED VIEW 1/1

39
A
A AZG-1
A
40

18
A 19 HT-SINK 38
17
48
P.C.B A
A A
B
F 49
A 47
15 WIRE,BINDER
16 HT-SINK
FL401 20 37
41 F
23
50 A
14 A
21 C P.C.B
22 B

A
28
13
27 G
25 A
24 A
H 26 A

A G
42
9 30 P.C.B
29 HT-SINK HT-SINK
E 31
32 I A
5 H 44
8
43
3
11 34

12 9 A
A
PLATE,EARTH MIC
33 A
6 35 45
1 7
10 CHAS,MAIN
D

2ZM-3 46
PLATE,EARTH MECH 35 33 36
F
2 4

37 38
MECHANISM EXPLODED VIEW 1/1 <2ZM-3MK2 PR4NM (HT)/2ZM-3MK2 YPR4NM(HA/LH)>

B
14 15
B

42 51
PH(DECK 1)
A RPH(DECK 2)
16 50 DECK C.B

52
53
12
13
53 54
17 18 50

11 10 a
49

44

41
9

7
54 b
47
43

3 35
48 41
19 E
2

33
45
5 6
a
20
4 46 31 34

HEAD 1 C.B(DECK 1) 56 37 D
22 d c
HEAD 2 C.B(DECK 2)
36
a 40
(DECK 1)
21 32 8

29 24 (DECK 1)
(DECK 2) 39
25 b

23 29 (DECK 2) d
26 38

c
a 27

28 C 30

55

39 40
MECHANISM MAIN PARTS LIST 1/1<2ZM-3MK2 PR4NM (HT)/2ZM-3MK2 YPR4NM(HA/LH)>

REF. NO PART NO. KANRI DESCRIPTION

NO.
1 82-ZM3-301-610 1H CHAS ASSY,M2
2 82-ZM1-258-210 0E SPR-T,PINCH L
3 82-ZM1-341-210 1A LVR ASSY,PINCH L2
4 82-ZM1-333-210 0E PLATE,LINK2
5 82-ZM1-266-310 0E LVR,DIR

6 82-ZM1-214-010 0E SPR-T,DIR
7 82-ZM1-206-910 1A CHAS,HEAD
8 82-ZM3-335-310 0E PULLEY,COUPLER M3
9 82-ZM1-269-210 0E SPR-T,BRG
10 82-ZM1-219-110 0E SPR-T,LINK

11 82-ZM1-210-110 0E GEAR,H T
12 82-ZM1-213-010 0E SPR-T,HEAD
13 82-ZM1-207-910 1A GUIDE,TAPE
14 86-ZM4-206-010 0E S-SCREW,AZIMUTH L
15 82-ZM1-314-110 0E PLATE,HEAD

16 82-ZM1-208-310 0E HLDR,HEAD
17 82-ZM1-218-010 0E SPR-E,HB
18 82-ZM3-342-010 0E BELT,SBU MOT 3
19 82-ZM1-222-210 0E LVR,PLAY
20 82-ZM1-217-410 0E REEL TABLE

21 82-ZM1-244-510 0E SPR-C,BT
22 82-ZM1-285-410 0E SPR-C,BT L
23 82-ZM1-257-010 0E SPR-T,CAS
24 82-ZM1-241-310 0E LVR,MC
25 82-ZM1-242-010 0E LVR,CAS

26 82-ZM1-243-010 0E LVR,STOP
27 82-ZM1-344-010 0E LVR ASSY,PINCH R2
28 82-ZM1-259-210 0E SPR-T,PINCH R
29 82-ZM1-240-110 0E LVR,REC(*)
30 80-ZM6-243-010 0E SH 1.75-3.6-0.5 SLT

31 82-ZM1-255-310 0E SPR-E,LVR DIR

32 82-ZM3-305-210 0E GEAR,CAM M2
33 82-ZM1-227-310 0E LVR,TRIG
34 82-ZM3-306-110 0E LVR,FR M2
35 82-ZM1-265-310 0E SPR-E,TRIG

36 82-ZM3-339-110 0E SHAFT,COUPLER N3
37 86-ZM1-206-010 0E BELT,MAIN L
38 82-ZM1-322-010 0E SPR-T,FR 60
39 82-ZM1-220-210 0E GEAR,IDLER
40 82-ZM3-616-010 0E RING MAGNET 4

41 82-ZM1-216-410 0E GEAR,REEL
42 87-A90-820-010 1D HEAD,PH HADKH25 FPC
42 87-A90-821-010 1H HEAD,RPH HADKH56 FPC
43 82-ZM1-225-210 0E GEAR,FR
44 82-ZM1-226-010 0E GEAR,REW

45 82-ZM3-333-310 1A SLIP DISK ASSY 2

46 82-ZM1-338-110 0E BELT,FR 4
47 82-ZM1-237-610 1A FLY-WHL,ASSY RW <DECK1>
47 09-001-420-010 1A FLY-WHL,R ASSY <DECK2>
48 82-ZM1-234-310 1A FLY-WHL,ASSY L <DECK1,2>

49 82-ZM3-329-410 0E BELT,SBU R2
50 82-ZM1-618-410 1B SOL ASSY,27
51 87-045-347-010 1H MOT,SHU2L 70
52 82-ZM3-221-210 0E PULLEY,MOT 2M
A 85-ZM3-202-010 0E S-SCREW,TG

B 80-ZM6-207-010 0E V+1.6-7
C 82-ZM3-318-110 0E S-SCREW W,MOTOR M2
D 87-B10-043-010 0E W-P,0.99-4-0.25 SLT
E 82-ZM3-334-010 0E PW 2.16-6-0.4
53 82-ZM3-307-010 CUSH-G, DIA3.7-8-3.2
54 82-ZM1-245-210 HLDR,IC
55 82-ZM1-288-010 SH,1.63-3.2-0.5 SLT
56 82-ZM3-340-010 SH,BELT D2

41
SPEAKER DISASSEMBLY INSTRUCTIONS

Type.1 Type.4

Insert a flat-bladed screwdriver into the position indicated by the TOOLS

arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer
unit and then remove the speaker units.
2 ( – ) flat head screwdriver
3 Cut chisel

1 2 3

How to Remove the PANEL, FR

Type.2 1. Insert the ( – ) flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
Remove the grill frame and four pieces of rubber caps by pulling head of the ( – ) flat head screwdriver with the plastic
out with a flat-bladed screwdriver. Remove the screws from hole hammer head, and create the clearance as shown in Fig-1.
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Re- 2. Insert the cut chisel in the clearance, and tap the head of
move the screws of each speaker unit and then remove the the cut chisel with plastic hammer as shown in Fig-2, to
speaker units. remove the PANEL, FR.

3. Place the speaker horizontally. Tap head of the cut chisel

with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.

Type.3

Insert a flat-bladed screwdriver into the position indicated by the

arrows and remove the panel. Turn the speaker unit to counter-
clockwisedirection while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the
speaker unit. After replacing the speaker unit, install it turning to Fig-1 Fig-2
clockwise direction until "click" sound comes out.

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.

42
SPEAKER PARTS LIST <SX–WNBL53>

REF. NO PART NO. KANRI DESCRIPTION

NO.
1 8A-NS5-001-010 PANEL,FR<YL>
1 8A-NS5-016-010 PANEL,FR U<YS>
2 8A-NS5-017-010 PLATE,NAME B
3 8A-NS5-004-010 PANEL,DUCT
4 8A-NS5-009-010 PROTECTOR,

5 8A-NS5-005-010 GRILLE,FRAME ASSY<YL>

5 8A-NS5-012-010 GRILLE,FRAME ASSY U<YS>
6 8A-NS5-015-010 BADGE,AIWA S35
7 8Z-NSY-003-010 CORD,BUSH
8 88-NS3-029-010 CORD,BUSH L

9 88-NS5-610-010 CORD,SPKR
10 88-NS5-611-010 CORD,SPKR B/L
11 8Z-NSY-608-010 SPKR, CERAMIC ASSY
12 8A-NS8-604-010 SPKR, M 100
13 8Z-NS7-602-010 SPKR, W 160

43
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
920074 Printed in Singapore