Roland TR-8 Cheatsheet by [email protected] v1.

Setup Operations

Setup settings are accessible by pressing and holding the PTN SELECT button whilst turning on the power of the TR-8.

Press START/STOP to save any changes.

Parameter Control Values Notes

OFF When a specific channel is set, this will be both Receive and
C1 - C16 Transmit channel (Default = 10)
MIDI Channel Tempo
ONn (OMNI) When OMNI is set, the Receive channel is ALL, the Transmit
channel is 10
LIT (AUTO) In AUTO, clock can either be via MIDI or USB.
Midi Clock source PAD 1
Unlit (INTERNAL) USB has priority
LIT (ON)
MIDI THRU PAD 2 When ON, MIDI out is also MIDI THRU
UNLIT (OFF)
LIT (ON)
Output Boost PAD 3 Boosts the output level of the MIX outputs only
UNLIT (OFF)
LIT (STEREO) Sets the EXTERNAL audio inputs to either a single STEREO pair, or
External IN Mode PAD 4
UNLIT (MONO) two MONO
LIT (Momentary) When set to LATCH, SCATTER will remain on when the SCATTER
Scatter Mode PAD 5
UNLIT (Latch) button is pressed.
LIT (ON) When switched ON, only MIDI clock is received at MIDI in. When
MIDI Play/Stop PAD 6
UNLIT (OFF) OFF, CLOCK STOP and START can be received
LIT (ON) When ON, sequencer uses precise timing, when OFF sequencer
Sequencer Timing PAD 7
UNLIT (OFF) emulates TR-808 timing.
ON: CH TUNE adjusts both CH and OH Tuning
LIT (ON) CH LEVEL adjusts volume of both CH and OH
HiHat Link
PAD 8 UH TUNE Adjusts tuning of cymbal sounds for the TR606 and
(With 7x7 Only)
UNLIT (OFF) TR8080
OFF: CH and OH tuning and volume are independent.
When ON, scale is changed by holding SCALE and turning
LIT (ON)
Scale TEMPO knob
Scale
(With 7x7 Only) When OFF, pressing SCALE button cycles through the scale
UNLIT (OFF)
settings
Instrument or External Assigns an instrument or external in to assignable output A
Assignable OUT A VARI 1
Button
Instrument or External Assigns an instrument or external in to assignable output B
Assignable OUT B VARI 2
Button
OFF - 20 Press and hold TAP and turn TEMPO knob to set time in minutes.
Screen Saver TAP + TEMPO
(Default = 5) Set to OFF to disable
1 = Default Press and hold SCATTER DEPTH and trun SCATTER wheel to select
SCATTER DEPTH +
PAD Colour Scheme 2 = Dimmed Default the desired scheme
WHEEL
3 -6 = Other Schemes
LIT (PAD) When LIT, pressing the instrument PAD value cycles between
UNLIT (INST) STRONG, WEAK, OFF
PAD Note Mode TR-REC
When UNLIT, PAD value is set by holding INST button and pressing
PAD.
LIT (KIT) When LIT, the effect type is saved with the selected drum kit
Effect Mode KIT
UNLIT (GLOBAL) When UNLIT, all kits have the same effect

The current version of this doc can be found at http://airainfo.org/files/tr-8_cheatsheet.pdf

 Roland TR-8 Cheatsheet by [email protected] v1.1

Pattern Operations

Function Selector Controller Notes

Select a Pattern PTN SELECT PAD
Random Pattern PTN SELECT (HOLD) SCATTER ON Sequencer needs to be stopped
Sequencer needs to be stopped
Copy
PTN SELECT (HOLD) PAD Whilst PTN SELECT pressed, press PAD to be copied from , then
Whole Pattern
press PAD for the pattern to be copied to
Sequencer needs to be stopped
Copy
PTN SELECT (HOLD) INST Whilst PTN SELECT pressed, press INST button for instruments to be
Instrument Pattern
copied, then press PAD for the pattern to be copied to
Delete a Pattern PTN SELECT CLEAR (HOLD) Press the PAD corresponding to the pattern to be deleted
Turn TEMPO knob to 'LcK' to prevent overwriting a pattern when
Pattern Lock PTN SELECT (HOLD) TEMPO
editing a pattern
Restart Pattern
TAP (HOLD) START/STOP Will restart the current playing pattern at the beginning
From Beginning

Kit Operations

Function Selector Controller Notes

Select a Kit DRUM SELECT KIT PAD
HOLD Drum Select Kit button down and turn TEMPO knob to select
Copy a Kit DRUM SELECT KIT TEMPO kit to copy
Press flashing PAD to complete COPY, or non-flashing PAD to cancel
Adjust Instrument Instrument Button +
DRUM SELECT KIT Value range 0 - 200
Gain Tempo Knob

The number of available Instruments depends on whether the 7x7

Change Instrument DRUM SELECT INST Instrument Button + PAD
expansion is installed. The PAD colour will reflect the instrument:
PINK=808, YELLOW=909, Orange=707, Blue=727,WHITE=606
Adjust Instrument Instrument Button +
DRUM SELECT INST Value range L64 - R64
Panning Tempo Knob

Effect Operations

Function Selector Controller Notes

Select Reverb Type DRUM SELECT INST Reverb STEP + PAD PADs 1 thru 8 only
Apply Reverb Step Reverb STEP PAD
Disable Instrument
DRUM SELECT KIT REVERB STEP (HOLD) Press INST buttons to Select/deselect
Reverb
Select Delay Type DRUM SELECT INST DELAY STEP + PAD PADs 1 thru 8 only
Apply Delay Step Delay STEP PAD
Disable Instrument
DRUM SELECT KIT DELAY STEP (HOLD) Press INST buttons to Select/deselect
Delay
Select Side Chain External In STEP PAD PADs 1 thru 8 only

Apply Side Chain Step External In STEP PAD

The current version of this doc can be found at http://airainfo.org/files/tr-8_cheatsheet.pdf

 Roland TR-8 Cheatsheet by [email protected] v1.1

Step Recording

Function Selector Controller Notes

Pattern Length LAST STEP PAD Specifies the number of steps in the sequence (default = 16)
Press the PAD corresponding to the step where an accent should
Apply Accent ACCENT STEP PAD
be played
Apply Reverb Step Reverb STEP PAD
Apply Delay Step Delay STEP PAD
Delete Pattern Part CLEAR (HOLD) Instrument Button Steps are cleared whilst CLEAR button is pressed
Delete Instrument Instrument Button
CLEAR
From Pattern (HOLD)
Play both Pattern A
Press A and B Parts A and B will play consecutively
and B
Edit Pattern A or B
TR-REC A or B
whilst playing
Press the PAD corresponding to the step where an accent should
Apply Accent ACCENT STEP (HOLD) PAD
be played
Plays alternate notes for some 707 and 727 sounds, or plays
weaker note for other sounds
707 Alternate Sounds:
Play Alternate
BD1/BD2, SD1/SD2
Sounds REVERB STEP (HOLD PAD
RS/Cowbell, HC/Tambourine
(With 7x7 Only)
727 Alternate Sounds:
H/L Bongo, Mute/Open High Conga
H/L Agogo, Cabasa/Maracas
Play a Flam
DELAY STEP (HOLD) PAD Apply a flam at the selected PAD
(With 7x7 Only)

RealTime Recording

Function Selector Controller Notes

Delete Pattern Part CLEAR (HOLD) Instrument Button Steps are cleared whilst CLEAR button is pressed
Delete Instrument Instrument Button
CLEAR
From Pattern (HOLD)
Press the PAD corresponding to the step where an accent should
Apply Accent ACCENT STEP (HOLD) PAD
be played
Plays alternate notes for some 707 and 727 sounds, or plays
weaker note for other sounds
707 Alternate Sounds:
Play Alternate
BD1/BD2, SD1/SD2
Sounds REVERB STEP (HOLD PAD
RS/Cowbell, HC/Tambourine
(With 7x7 Only)
727 Alternate Sounds:
H/L Bongo, Mute/Open High Conga
H/L Agogo, Cabasa/Maracas
Play a Flam
DELAY STEP (HOLD) PAD Apply a flam at the selected PAD
(With 7x7 Only)
Flam Spacing Adjusts flam spacing from 0 thru' 8.
TR-REC (HOLD) TEMPO
(With 7x7 Only) When set to 0 flam has no effect

The current version of this doc can be found at http://airainfo.org/files/tr-8_cheatsheet.pdf

 Roland TR-8 Cheatsheet by [email protected] v1.1

MIDI Controls

Control Change Function

9 SHUFFLE
12 EXTERNAL IN LEVEL
13 EXTERNAL IN SIDE CHAIN
16 DELAY LEVEL
17 DELAY TIME
18 DELAY FEEDBACK
20 BD TUNE
21 BD ATTACK
22 BD COMP
23 BD DECAY
24 BD LEVEL
25 SD TUNE
26 SD SNAPPY
27 SD COMP
28 SD DECAY
29 SD LEVEL
46 LT TUNE
47 LT DECAY
48 LT LEVEL
49 MT TUNE
50 MT DECAY
51 MT LEVEL
52 HT TUNE
53 HT DECAY
54 HT LEVEL
55 RS TUNE
56 RS DECAY
57 RS LEVEL
58 HC TUNE
59 HC DECAY
60 HC LEVEL
61 CH TUNE
62 CH DECAY
63 CH LEVEL
68 SCATTER TYPE
69 SCATTER DEPTH
70 SCATTER SW
71 ACCENT
80 OH TUNE
81 OH DECAY
82 OH LEVEL
83 CC TUNE
84 CC DECAY
85 CC LEVEL
86 RC TUNE
87 RC DECAY
88 RC LEVEL
89 REVERB TIME
90 REVERB GATE
91 REVERB LEVEL

MIDI Note Function

C0 ACCENT PATTERN ALL ON/OFF
D0 REVERB PATTERN ALL ON/OFF
E0 DELAY PATTERN ALL ON/OFF
F0 EXT. IN PATTERN ALL ON/OFF
G0 ACCENT PATTERN ALL MUTE
A0 REVERB PATTERN ALL MUTE
B0 DELAY PATTERN ALL MUTE
C1 EXT. IN PATTERN ALL MUTE

The current version of this doc can be found at http://airainfo.org/files/tr-8_cheatsheet.pdf