Received April 23, 2019, accepted May 18, 2019, date of publication May 22, 2019, date of current

version June 4, 2019.

Digital Object Identifier 10.1109/ACCESS.2019.2918231

A 1-Bit Electronically Reconfigurable

Reflectarray Antenna in X Band
HAI ZHANG, XUXIANG CHEN, (Student Member, IEEE), ZHENGLONG WANG,
YUEHE GE , (Member, IEEE), AND JIXIONG PU
College of Information Science and Engineering, Huaqiao University, Xiamen 361021, China
Corresponding author: Yuehe Ge ([email protected])
This work was supported in part by the National Natural Science Foundation of China (NSFC) under Grant 11674111, Grant 61575070, and
Grant 11750110426, in part by the Natural Science Foundation of Fujian Province, China, under Grant 2017J01003 and Grant 2017J01115,
in part by the Foreign Cooperation Projects in Fujian Province, China, under Grant 2016I0008, in part by the Foreign Cooperation Projects
of Quanzhou City Science and Technology Program of China under Grant 2017T005, and in part by the Subsidized Projects for
Postgraduates’ Innovative Fund in Scientific Research of Huaqiao University under Grant 1511301030 and Grant 17013082024.

ABSTRACT In this paper, a fully electronically reconfigurable reflectarray antenna that has 14×14 reflecting
elements and features a higher aperture efficiency was designed, fabricated, and tested. A new configuration
of the reflecting element was first developed so that all the bias circuit and the PIN diode are arranged on
the opposite side of the reflecting surface, avoiding the potential unexpected reflection and aiming at the
improvement of the antenna efficiency. The new reflecting element, which has a smaller size (0.365λ), was
then applied to the design of a 14 × 14 reconfigurable reflectarray antenna. A field programmable gate
array (FPGA)-based beam control system was also developed for the realization of an electronically beam-
scanning performance. The measurements of the prototype of the integrated reconfigurable reflectarray
antenna show good beam-scanning radiation performance, a peak gain of 19.2 dBi, and an aperture efficiency
of about 25%.

INDEX TERMS Reflectarray antenna, reconfigurable antenna, beam-scanning, PIN diode.

I. INTRODUCTION may not be enough for most beam steering antennas. The
Reflectarray antennas [1]–[3] are exciting high-gain anten- phase tuning ability of the varactor is much more powerful.
nas that exhibit many advantages over their parabolic coun- Nearly 360◦ phase range was achieved by loading a varactor
terparts, such as low profile, ease of manufacturing, low diode with the patch [7]. However, the unit cell has a high
fabrication cost and the possibilities of beam forming and insertion loss of 3.7 dB. To solve this problem, amplifiers
scanning. Recently, much effort has been made to study were integrated with the unit cell, but this would result in
the electronically reconfigurable reflectarrays [4]–[17] and increased complexity [7]. In addition, the narrow bandwidths
transmitarrays [18]–[21], which not only possess the advan- for the unit cells reported in [4]–[7], [18] also limited their
tages mentioned above, but also provide flexibly scanning applications. Recently, phase reconfigurable unit cells based
beams without using the complicated and high-cost feeding on PIN diodes have been well developed with the reduced
networks. phase resolution (1-bit, typically) [12]–[15], [17], [19]–[21].
Electronically reconfigurable reflectarrays carry out the In these designs, including both reconfigurable reflectarrays
functionalities of beam scanning and beamforming by chang- and transmitarrays, the beam-scanning performance based
ing the reflection phase of each element on reflectarrays on the 1-bit phase changes has been experimentally demon-
through controlling active devices. Examples of such active strated and studied. It is found that all the 1-bit reconfigurable
devices include liquid crystal materials [4], [5], varactor antenna arrays in literatures have low aperture efficiencies.
diodes [6], [7], [18], RF-MEMS technology [8]–[10], PIN In this paper, we present a new configuration of the
diodes [12]–[17], [19]–[21], etc.. In [4], the main beam is 1-bit phase-reconfigurable unit cell for reconfigurable
able to steer to ± 6◦ by using the liquid crystal, which reflectarray antennas, which uses only one PIN diode placed
on the opposite side of the reflection surface. In the
The associate editor coordinating the review of this manuscript and current reconfigurable reflectarray antennas [9]–[16], the PIN
approving it for publication was Mohsen Khalily. diodes and the solders appear on the reflection surface of
2169-3536 2019 IEEE. Translations and content mining are permitted for academic research only.
VOLUME 7, 2019 Personal use is also permitted, but republication/redistribution requires IEEE permission. 66567
See http://www.ieee.org/publications_standards/publications/rights/index.html for more information.
 H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

FIGURE 1. Geometry of the unit cell: (a) Schematic 3-D view; (b) Layout of
top, middle and bottom layers.

FIGURE 2. Electric field distributions on the top and bottom layers:

(a) ‘‘ON’’ state; (b) ‘‘OFF’’ state.
reflectarrays, which might lead to undesirable scattering
and hence deteriorate the radiation performance of reflectar-
rays. In our new design, the PIN diodes, other passive and PEC ground. The other end of the line is connected to the PEC
active lumped devices and the associated solders are arranged ground through a metallic blind via near the middle of the
not to appear on the reflection surface of reflectarrays. In element. There is a gap in the middle of the line where locates
addition, the proposed unit cell has a smaller size, only the selected PIN diode. The diode should have a small size
0.365λ, while those in [12]–[15] are greater than or equal and a low insertion loss at the operating frequency, 12 GHz.
to 0.5λ. It is expected that low loss is achieved regardless The M/ACOM PIN diode, MA4AGFCP910, is used in this
of the states of the PIN diode and a higher aperture effi- work. In simulations, the PIN diode is modelled as a lumped
ciency can be obtained. Simulations and measurements are resistance with the typical value of 5.2  for forward bias
first conducted to validate the proposed unit cell design. (‘‘ON’’ state), while for reverse bias (‘‘OFF’’ state), it acts as
A 14 × 14 reconfigurable reflectarray antenna was then a lumped capacitance with the typical value of 18 fF.
developed for the study of the beam-scanning radiation The reflection patch on the reflecting element acts as a
performance. In order to comprehensively investigate the scatterer controlling the polarization of the reflection wave
performance of the new beam-scanning antenna, a field and affecting the reflection phase. The PIN diode is used to
programmable gate array (FPGA)-based beam controller was connect the PEC ground to the patch through the grounded
also developed. The antenna prototype is fabricated and line and two vias. By controlling the operating states of the
tested. This paper is organized as follows. Section II intro- PIN diode, namely ‘‘ON’’ and ‘‘OFF’’ states, the patch will
duces the new configuration of the 1-bit unit cell and the sim- be connected and disconnected to the ground, respectively,
ulated and experimental characterization results. Section III resulting in different reflection performance of the reflecting
describes the designs of the 14 × 14 reflectarray antenna element [13]–[15]. It is expected that nearly unity reflection
and the beam controller, as well as simulation results of amplitude for both states whilst a 180◦ phase difference
the reflectarray antenna. The fabrication and the measured between them can be achieved. In order to drive the PIN
beam-scanning performance of the antenna prototype and diode to change the reflection phase of the unit cell while
the discussion of the experimental results are presented in minimizing its influence on the reflection amplitude, it is
Section IV. Section V summarizes this paper. necessary to design a proper dc-biasing network. The biasing
circuit has to be designed in such a way that the biasing
II. REFLECTARRAY ELEMENT DESIGN AND point should be placed at the position with the electric field
CHARACTERIZATION of nearly zero. A quarter-wavelength microstrip line with an
A. UNIT CELL DESIGN open-ended radial stub is considered [14], [15] to isolate the
The configuration of the proposed 1-bit reflecting element is RF signal from the dc signal. Fig. 2 shows the electric field
schematically illustrated in Fig. 1. It consists of two stacked distributions on the surfaces of top and bottom layers for
dielectric layers, a rectangular metallic patch (w × l) printed both ‘‘on’’ and ‘‘off’’ states under the y-polarized incident
on the top surface of the upper layer, a perfect electric conduc- wave. It can be seen that the amplitude of the electric field
tor (PEC) ground between the two layers and a grounded line on the position of the biasing line, where the open-ended
and a biasing circuit as well as a PIN diode on the bottom radial stub is connected, is nearly zero. While the PIN diode
surface of the lower layer. The two dielectric layers, which in this design is mounted on the bottom of the layer, which
have no air gap in between, use Arlon AD255 (εr = 2.55, avoids the scattering resulting from the PIN diode and the
tanδ = 0.0014) and FR4 ( εr = 4.40, tanδ = 0.02) sub- solders, the operating principle of the unit cell is similar to
strates, respectively. The patch is connected to one end of the those of [14], [15], which is that by changing the state of the
ground line through a metallic via, which is isolated from the PIN diode into ‘‘ON’’ or ‘‘OFF’’, the resonant frequencies

66568 VOLUME 7, 2019

H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

FIGURE 4. Simulated reflection phase and amplitude of the proposed

element under the normal incidence.

FIGURE 3. Reflection amplitudes and phases with different positions of

the vias and the PIN diode: (a) via2 and the PIN diode are fixed, via1 is
varied and the Pin diode is at ‘‘OFF’’ state; (b) via2 and the PIN diode are
fixed, via1 is varied and the Pin diode is at ‘‘ON’’ state; (c) via1 is fixed,
via2 and the PIN diode are varied and Pin diode is at ‘‘OFF’’ state;
(d) via1 is fixed, via2 and the PIN diode are varied and Pin diode is at
‘‘ON’’ state.

of the reflecting unit cell are different, resulting in different

reflection phases. The size of the unit cell is also smaller, only
0.365λ×0.365λ, while the counterparts in [14], [15] are both
0.5λ × 0.5λ. The corresponding geometry parameters of the
final design, shown in Fig. 1, are as follows: p = 9.525 mm,
w = 5.85 mm, l = 6.8 mm, t1 = 1.58 mm, t2 = 0.5 mm, FIGURE 5. Photographs of the fabricated samples and measurement
setup: (a) Three identical elements; (b) Transition; (c) Measurement setup.
di = 0.3 mm, do = 2.2 mm, s1 = 1.2 mm, s2 = 1.2 mm,
pl = 0.3 mm, and pw = 0.3 mm.
adaptor and a WR75 waveguide. In addition, the mea-
B. SIMULATED AND EXPERIMENTAL CHARACTERIZATION surement setup also includes a transition between the
We carried out numerical simulations by using the commer- WR75 waveguide (9.525 mm × 19.05 mm) and the three
cial full-wave EM software Ansys HFSS. The effects of the unit cells (9.525 mm × 28.575 mm) due to their dif-
positions of via1, via2 and the PIN diode on the reflec- ferent dimensions, as shown in Fig. 5(b). The reflect-
tion amplitude and phase are first studied. Fig. 3 shows the ing elements under measurement are shown in Fig. 5(c).
results. As can be seen, the reflection amplitude and phase In the WGS, all the walls of the waveguide are per-
are more or less affected by the positions of the vias and the fect conductors. In order to characterize an element of
PIN diode. The final results with parameters above are plotted an array, the oblique incidence should be applied in the
in Fig. 4. It is observed that the phase difference (δ) between E-plane of the element, as detailed in [22], [23].
the ‘‘ON’’ and ‘‘OFF’’ states is very close to 180◦ from 10.9 to Fig. 6 shows the comparisons between the simulated
12.1 GHz, indicating that the required binary reconfigurable results using periodic boundary conditions (PBCs) under the
phases are successfully obtained. Furthermore, there is no normal incidence and the WGS results from both simula-
remarkable difference between the two reflection amplitudes, tions and experiments. The agreements of reflection phases
which are both above −0.7 dB, regardless of the PIN diode among the three cases are good and all the three phase
states. differences within the frequency range of 11-12 GHz are in
For experimental verification, several identical samples the range of 180◦ −200◦ . Although the reflection amplitudes
are fabricated and measured using a waveguide simulator show slight differences, they are all above −1 dB at 11-12
(WGS) [22], [23]. The front and back views of the pro- GHz. These slight differences are attributed to the fabrication
totypes are shown in Fig. 5(a). The sample consists of tolerance and assembly misalignment among the waveguide,
three identical elements. In order to avoid the propagation the transition and the fabricated sample. In summary, these
of substrate modes outside the elements, a rectangular ring results demonstrate that the proposed design is capable of
formed by metallic vias is made surrounding the three ele- forming 1-bit reconfigurable reflectarray antennas, developed
ments. The test system is composed of a coax-to-WR75 in the next section.

VOLUME 7, 2019 66569

 H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

FIGURE 7. Schematic reconfigurable reflectarray antenna and the

coordinate system.

is [14], [15]. In our design, a reflectarray with 14 × 14

elements is considered.
Fig. 7 shows the schematic geometry of the reconfig-
urable reflectarray antenna, where F is the focusing distance
between the phase center of the feed and the reflectarray, Ri
is the distance between the feed and the ith element on the
*
reflectarray, r i is the position vector of the ith element, and
FIGURE 6. Comparison between simulated and measured reflection û0 is the unit vector of the main beam direction. The required
performance: (a) Phases; (b) Amplitudes. compensation phase of each element can be obtained using
the following equation [1]
 
*
III. RECONFIGURABLE REFLECTARRAY ANTENNA ϕi = k Ri − F + r i · û0 ∓ 2nπ + ϕ0 (1)
After the successful design of the reflecting element, a 1-bit
reconfigurable reflectarray consisting of 14 × 14 elements where ϕi and ϕ0 are the compensation phases of the ith and
was designed. The schematic reconfigurable reflectarray the center elements of the reflectarray respectively, k is the
antenna, shown in Fig. 7, is composed of a feed, a reflectarray propagation constant, and n is an integer number to make sure
and a beam-scanning controller. The incident wave from the that 0 < ϕi < 360◦ . In our design, the compensation phase
feed horn illuminates the reflectarray. The reflection phases will be 0◦ when −90◦ < ϕi < 90◦ and 180◦ for other ϕi .
of all elements on the reflectarray are only 0◦ or 180◦ , which
B. FEED
are controlled by the beam-scanning controller. In order to
realize radiation patterns with required main beam direc- Normally the illumination at the reflectarray edge from the
tions or shaped beams, the appropriate design considerations feed is about −10 dB [1]. In order to appropriately illuminate
of the antennas are required, as follows. the reflectarray, a conical horn antenna that has a gain of
around 15 dBi at 12 GHz is first developed. Due to the
limited reflectarray aperture size, which is 134 × 134 mm2 ,
A. REFLECTARRAY DESIGN
−9 dB illumination at the reflectarray edge is applied and
The common methods to design planar reflectarrays include hence the focusing length of the feed horn is 189 mm. The
Fresnel zone principle and the phase compensation method. phase center of the horn is about 7.4 mm below the horn
The latter ideally needs continuous compensation phases over aperture. Therefore, the length between the horn aperture
0◦ −360◦ . However, discrete phases are used in practice, and the surface of the reflectarray is 181.6 mm. In addition,
resulting in the reduction of the radiation performance of in order to avoid the blockage of the feed when the antenna
reflectarrays, such as the gain, the sidelobe level, the beam beam is scanning, the offset feed is necessary. In our design,
direction errors, etc.. In this work, the compensation phases the feed horn is located in the XOZ plane and the offset angle
are only 0◦ and 180◦ , which are the minimum requirement is 17.5◦ .
for the phase compensation method. It is well known that
the radiation performance of reflectarray antennas using such C. SIMULATIONS
kind of phase compensation would be improved with the The reconfigurable reflectarray antenna design is first sim-
increase of the antenna size, namely, the more elements ulated to evaluate its potential performance. Commercial
the reflectarray has the better the radiation performance softwave Ansys HFSS is applied to carry out simulations.

66570 VOLUME 7, 2019

H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

FIGURE 9. (a) Phase distributions for main beams of −10◦ and 10◦
respectively; (b) The simulated scanning radiation patterns from −30◦ to
60◦ with a 10◦ step at 11.5 GHz in the XOZ plane.

FIGURE 8. Simulated radiation patterns at 11.5 GHz for three reflectarrays

with different sizes.

In our simulations, the exactly same reflecting element

and horn models, as shown in Fig. 1 and designed in
Section III-B, are applied to form the reflectarray antenna
models. Therefore, the phase change for each element on
the reflectarray, according to the requirements of the beam
scanning, will be carried out by changing the ‘‘ON’’ and
‘‘OFF’’ states of the diode on the element.
The radiation performance for reflectarrays with different
sizes are first simulated. Reflectarrays with 10 × 10, 12 × 12,
and 14 × 14 elements are respectively applied. Fig. 8 shows
the simulated radiation patterns with main beam direction of
(θ = 0◦ , ϕ = 0◦ ) at 11.5 GHz. As predicted, the performance
of the main beam, the sidelobe level and the backlobe level
are improved with the increase of the reflectarray size. It can
be seen that the reflectarray with 14 × 14 elements gives rea-
sonable radiation pattern whereas the other two cases result
in some distortion in the main beam and high-level sidelobes
and backlobes. Hence, the reflectarray with 14 × 14 elements
is applied to the design in this work.
Next, the radiation patterns with the main beam direc-
FIGURE 10. Beam control circuitry of the reflectarray.
tions from −30◦ to 60◦ with a 10◦ step are simulated in
the XOZ plane at 11.5 GHz. The phase distributions on
the 14 × 14 reflectarray elements for different main beam
directions are obtained using formula (1). Fig. 9(a) plots the D. BEAM-SCANNING CONTROLLER
phase and diode state distributions for the main beams of In order to carry out the beam scanning performance and con-
−10◦ and 10◦ in the XOZ plane. The simulated radiation trol the main beam direction, a beam controller is developed
patterns are depicted in Fig. 9(b). Due to the blockage of the to control the diode states of each element on the reflectar-
feed, which is also in the XOZ plane, the radiation patterns ray. Since each element is controlled by a PIN diode, total
with main beam directions of −30◦ , −20◦ and −10◦ have 196 PIN diodes and the equivalent number of biasing lines
the relatively larger sidelobe levels while the performance of are needed to control the entire reflectarray. The schematic
those with main beam directions greater than 40◦ will deteri- control circuitry is illustrated in Fig. 10, which is mainly
orate because the beamwidths become wider and distortion. composed of a micro-controller-unit (MCU) and a voltage
The simulated performance confirms to the prediction and distribution controller (VDC). The VDC has ten inputs and
demonstrates the validation of the antenna design. The best 196 outputs. The outputs are voltages, applied to the diodes
gain appears when the main beam direction is 10◦ in the XOZ of elements on the reflectarray through biasing lines and used
plane, which is about 20 dBi and the corresponding aperture to control the ‘‘ON’’ and ‘‘OFF’’ states of diodes. The ten
efficiency is 30.45%. inputs are used to control the 196 outputs. Each input has

VOLUME 7, 2019 66571

 H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

either ‘‘0’’ or ‘‘1’’ state. Therefore, the 10-bit inputs are able
to totally control (or select) 1024 (210 ) different groups of
outputs, corresponding to 1024 different radiation beams.
In our beam control system, the VDC was implemented
using the voltage control circuit based on a field pro-
grammable gate array (FPGA), which is based on Cyclone IV
series chips. The supply voltage of the circuit board is 5V
while the output voltage of each output is either 0 V or 3.3 V.
Due to the operating voltage 1.33V of the PIN diodes, a series
resistor R is needed in each biasing line, as shown in Fig. 10.
Each scanning beam of the reconfigurable reflectarray
antenna corresponds to a phase distribution on the 14 × 14
reflection elements, which is realized by a group of 196 out-
puts of the VDC. All phase distributions of the designated FIGURE 11. Fabricated reflectarray antenna prototype.
beams can be determined in advance, using formula (1).
Therefore, all the corresponding groups of 196 outputs can
be estimated and stored in advance in the FPGA based beam
control system. The required beams can be selected by the
10-bit digit inputs controlled by the MCU.

IV. EXPERIMENTAL RESULTS AND DISCUSSION

A. REFLECTARRAY PROTOTYPE
In order to experimentally validate the reconfigurable reflec-
tarray antenna design in this work, an antenna prototype,
including the feed horn, the reflectarray and the beam con-
troller, are fabricated. Arlon AD255 and FR4 substrates, with
thicknesses of 1.58 mm and 0.5 mm respectively, are applied
to the fabrication of the reflectarray, which includes 14 × 14
elements and has a surface size of 134 × 134 mm2 . The
normal PCB techniques are applied to the fabrication of the FIGURE 12. Measured radiation patterns for the main beam scanned
from −30◦ to 60◦ with a step of 10◦ in the XOZ plane at 11.5 GHz.
reflectarray and the beam controller. Since there is no gap
between the two substrates of the reflectarray, an ultrathin
FR4 PP sheet is used to agglutinate the two substrates. The
contributed that the position of the feed horn in measurements
total thickness of the reflactarray board is less than 2.1 mm.
is slightly deviated from the determined place due to the
Fig. 11 shows the mounted antenna prototype. It can be seen
misalignment during the antenna mounting and the deviation
that there are only square metallic patches on the reflection
during the rotation of the antenna under measurements. The
surface of the reflactarray. All the diodes, series resistors, and
offset angle might change due to the aforementioned reasons
biasing lines are located on the surface of the FR4 substrate,
in the measurements. During the measurement of each beam,
opposite side of the reflectarray. The beam controller board
the receiving signal amplitudes are automatically normal-
is mounted below the reflectarray, as shown in Fig. 11. The
ized to the maxima by the measurement software. Therefore,
outputs of the VDC are connected to the biasing lines using
the gain reduction cannot be plotted in Fig. 12. In addition,
the normal flat ribbon cables.
with the increase of the scanning angle, the sidelobe levels
and the main beams also deteriorate. The main reason is that
B. RADIATION PERFORMANCE the reduction of the reflection amplitudes and the phase errors
The mounted reflectarray antenna, shown in Fig. 11, was from the reflectarray elements will increase with the scanning
measured using a far-field testing system in an anechoic angle. Table 1 lists the measured beam direction errors and
chamber. The radiation performance in the XOZ plane, where the HPBW for each scanning beam. The measured gains and
the feed horn is located, is first measured at 11.5 GHz. aperture efficiencies for different scanning beams in the XOZ
The measured radiation patterns with main beam direc- plane at 11.5 GHz are also measured and depicted in Fig. 13,
tions from −30◦ to 60◦ , stepped by 10◦ , were plotted in together with simulated ones for comparison. The measured
Fig. 12. Due to the blockage of the feed, the patterns with peak gain appears at the 10◦ main beam, about 19.2 dB. The
the main beam close to the position of the feed, such as corresponding peak aperture efficiency is about 25%. Due to
−30◦ , −20◦ , −10◦ , and 0◦ , have high-level sidelobes and the blockage of the feed and the tolerance when mounting the
abnormal half-power beamwidths (HPBW), which are dif- feed horn, the gain drops a lot when the beam scanning angle
ferent than simulated ones in Fig. 9. The main reason is is close to the direction of the feed.

66572 VOLUME 7, 2019

H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

TABLE 1. Measured beam direction errors and HPBW under different

beam directions at 11.5 GHz in the XOZ plane.

FIGURE 15. The measured and simulated gains and aperture efficiencies
for different scanning beams in the YOZ plane at 11.5 GHz.

FIGURE 13. The measured and simulated gains and aperture efficiencies
for different scanning beams in the XOZ plane at 11.5 GHz.

FIGURE 16. Measured gain and aperture efficiency curves for the main
beam fixed at 10◦ in the XOZ plane.

in the XOZ plane, the beam direction errors are much less,
and the gains do not drop significantly with the increase
of scanning angles. The radiation performance for differ-
ent frequencies is also tested. Fig. 16 shows the measured
gain and efficiency curves for the main beam fixed at 10◦
(θ = 10◦ , ϕ = 0◦ ) in the XOZ plane.
Table 2 compares the performance, the size and the
working modes of the proposed antenna to those reported
FIGURE 14. Measured radiation patterns for main beams scanned from in literatures. It is shown that the proposed 1-bit reconfig-
−60◦ to 60◦ with a step of 10◦ in the YOZ plane at 11.5 GHz. urable reflectarray antenna design features a higher aperture
efficiency, achieving the main target of this work.

The radiation performance in the YOZ plane at 11.5 GHz C. DISCUSSION

is also measured. In the measurement, the beam scans from Overall, the experimental results successfully demonstrate
−60◦ to 60◦ , with a step of 10◦ . Fig. 14 and 15 plot the the beam-scanning radiation performance of the reconfig-
measured radiation patterns, the gains and the aperture effi- urable reflectarray antenna design, validating the reflecting
ciencies respectively. Same as those in the XOZ plane, element design in Section II. Nevertheless, the radiation
the radiation performance deteriorate when the scanning performance deteriorates with the increase of the scanning
angles are greater than 40◦ . Since there is no blockage in the angle. The gain drops a lot and the HPBW distorts much.
YOZ plane, the sidelobe levels are much better than those The main reasons include the feed blockage, the substrate

VOLUME 7, 2019 66573

 H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

TABLE 2. Comparison of different reconfigurable antenna arrays. 1-bit reconfigurable reflectarray might be mitigated by
using elements with a smaller size. Both simulations in
Section III-C and experiments in Section IV-B show the
realization of our initial target. It is expected that the recon-
figurable reflectarray antenna based on our reflecting element
is able to achieve better aperture efficiency when with larger
aperture sizes.

V. CONCLUSION
We have successfully demonstrated an X-band electronically
reconfigurable reflectarray antenna that has 14×14 reflecting
elements and features a higher aperture efficiency. A 1-bit
electronically controlled reflecting element with only one
PIN diode and a smaller period (0.365λ) has been success-
fully developed for reconfigurable reflectarray antennas. The
180◦ phase difference is achieved by controlling the ‘‘ON’’
and ‘‘OFF’’ states of the PIN diode mounted on the opposite
tolerance and the fabrication tolerance, as well as the mount- side of the reflection surface, with the reflection amplitude
ing tolerance of the feed and the measurement tolerance due of > −1dB. Measurements in a WGS show good agree-
to the misalignment of the antenna during measurements. ments with the simulated results, validating the proposed
In addition, due to the laboratory condition, all the diodes design.
and resistors are soldered manually. The non-uniform solders A 14 × 14 reflectarray, a feed horn and a FPGA based
in different elements might slightly affect their performance. beam controller are further developed to demonstrate the
Above all is the size of the reflectarray. As mentioned in beam-scanning radiation performance. The measured results
Section III and demonstrated in [14], [15], the radiation per- show a peak gain of 19.2 dBi and an aperture efficiency
formance of such kind of reconfigurable reflectarray antennas of 25% at 11.5 GHz, realizing one of the main aims of this
will become better and the performance deterioration with work, namely, to improve the antenna efficiency. Good beam-
the increase of the scanning angle will mitigate when the scanning performance is achieved in a 2D space. This antenna
reflectarray size is large enough. is able to be scaled to operate at other frequencies. The poten-
In spite of all these, it should be noted that the mea- tial applications include current and future communication,
sured peak aperture efficiency is about 25%. Compared with satellite and radar systems.
those in literatures, for example, 17.9% in [14] and 21.6%
in [15], our results show better aperture efficiency. Note that REFERENCES
the reflectarrays in [14], [15] use similar reflecting element, [1] J. Huang and J. A. Encinar, Reflectarray Antennas, Piscataway, NY, USA:
include 10 × 10 and 40 × 40 elements respectively, which Wiley, 2008.
[2] Y. Chen, Y. Ge, and T. S. Bird, ‘‘An offset reflectarray antenna for multi-
demonstrate that the aperture efficiency is improved with the polarization applications,’’ IEEE Antennas Wireless Propag. Lett., vol. 15,
increase of the reflectarray aperture size. The main reason pp. 1353–1356, 2015.
for the higher aperture efficiency in our reflectarray design [3] M. H. Dahri, M. I. Abbasi, M. H. Jamaluddin, and M. R. Kamarudin,
‘‘A review of high gain and high efficiency reflectarrays for 5G communi-
is attributed to the arrangement of the PIN diodes in our ele- cations,’’ IEEE Access, vol. 6, pp. 5973–5985, 2018.
ment design, the smaller size of the reflectarray element and [4] G. Perez-Palomino, R. Florencio, J. A. Encinar, M. Barba, R. Dickie,
perhaps the use of Arlon AD255 substrate, which has a minor R. Cahill, P. Baine, M. Bain, and R. R. Boix, ‘‘Accurate and effi-
cient modeling to calculate the voltage dependence of liquid crystal-
smaller loss tangent (tanδ = 0.0014) than Taconic TLX-8 based reflectarray cells,’’ IEEE Trans. Antennas Propag., vol. 62, no. 5,
(tanδ = 0.0019) in [14], [15]. As mentioned in Section I, pp. 2659–2668, May 2014.
the main difference between our reflecting element and all [5] S. Bildik, S. Dieter, C. Fritzsch, W. Menzel, and R. Jakoby, ‘‘Reconfig-
urable folded reflectarray antenna based upon liquid crystal technology,’’
others in literatures is that the PIN diode and the associated
IEEE Trans. Antennas Propag., vol. 63, no. 1, pp. 122–132, Jan. 2015.
biasing line and solders are designed to be located in the [6] S. V. Hum, M. Okoniewski, and R. J. Davies, ‘‘Modeling and design
opposite side of the reflection surface of the element, aiming of electronically tunable reflectarrays,’’ IEEE Trans. Antennas Propag.,
at the improvement of the antenna efficiency. In addition, vol. 55, no. 8, pp. 2200–2210, Aug. 2007.
[7] F. Venneri, S. Costanzo, G. Di Massa, E. Marozzo, A. Borgia,
although our reflectarray has 14 × 14 elements while that P. Corsonello, and M. Salzano, ‘‘Beam-scanning reflectarray based on
in [14] has 10 × 10 elements, the two reflectarrays have a single varactor-tuned element,’’ Int. J. Antennas Propag., vol. 2012,
similar aperture size, 5.1λ × 5.1λ and 5λ × 5λ respectively. Jan. 2012, Art. no. 290285.
[8] H. Rajagopalan, Y. Rahmat-Samii, and W. A. Imbriale, ‘‘RF MEMS actu-
The size of the element in our reflectarray design is smaller. ated reconfigurable reflectarray patch-slot element,’’ IEEE Trans. Anten-
With the similar aperture size, the same 1-bit compensation nas Propag., vol. 56, no. 12, pp. 3689–3699, Dec. 2008.
phase while more reflectarray elements, our design exhibits [9] E. Carrasco, M. Barba, B. Reig, C. Dieppedale, and J. A. Encinar, ‘‘Char-
acterization of a reflectarray gathered element with electronic control using
a higher aperture efficiency, illustrating that the negative ohmic RF MEMS and patches aperture-coupled to a delay line,’’ IEEE
effect of phase errors on the radiation performance of an Trans. Antennas Propag., vol. 60, no. 9, pp. 4190–4201, Sep. 2012.

66574 VOLUME 7, 2019

H. Zhang et al.: 1-Bit Electronically Reconfigurable Reflectarray Antenna in X Band

[10] T. Debogovic and J. Perruisseau-Carrier, ‘‘Low loss MEMS-reconfigurable XUXIANG CHEN (S’17) was born in Jiangsu,
1-bit reflectarray cell with dual-linear polarization,’’ IEEE Trans. Antennas China, in 1992. He received the B.E. degree in
Propag., vol. 62, no. 10, pp. 5055–5060, Oct. 2014. electronic information engineering and the M.E.
[11] S. V. Hum and J. Perruisseau-Carrier, ‘‘Reconfigurable reflectarrays and degree in electromagnetic field and microwave
array lenses for dynamic antenna beam control: A review,’’ IEEE Trans. technology from Huaqiao University, Xiamen,
Antennas Propag., vol. 62, no. 1, pp. 183–198, Jan. 2014. China. He is currently an Engineer with Antenna
[12] H. Kamoda, T. Iwasaki, J. Tsumochi, T. Kuki, and O. Hashimoto, and Subsystems Business Unit, Comba Telecom
‘‘60-GHz electronically reconfigurable large reflectarray using single-
Systems Ltd., Guangzhou, China. His current
bit phase shifters,’’ IEEE Trans. Antennas Propag., vol. 59, no. 7,
research interests include reconfigurable antennas,
pp. 2524–2531, Jul. 2011.
[13] E. Carrasco, M. Barba, and J. A. Encinar, ‘‘X-band reflectarray antenna reflectarrays and transmitarrays, and metasurfaces
with switching-beam using PIN diodes and gathered elements,’’ IEEE and its applications.
Trans. Antennas Propag., vol. 60, no. 12, pp. 5700–5708, Dec. 2012. Mr. Chen received the Honorable Mention Awards of Student Paper
[14] H. Yang, F. Yang, S. Xu, Y. Mao, M. Li, X. Cao, and J. Gao, Competition at the 2017 IEEE AP-S Symposium on Antennas and Propa-
‘‘A 1-bit 10×10 reconfigurable reflectarray antenna: Design, optimiza- gation and USNC-URSI Radio Science Meeting (APS 2017) and the 2018
tion, and experiment,’’ IEEE Trans. Antenna Propag, vol. 64, no. 6, IEEE International Workshop on Antenna Technology: Small Antennas and
pp. 2246–2254, Jun. 2016. Innovative Structures.
[15] H. Yang, F. Yang, X. Cao, S. Xu, J. Gao, X. Chen, M. Li, and T. Li,
‘‘A 1600-element dual-frequency electronically reconfigurable reflectar-
ray at X/Ku-band,’’ IEEE Trans. Antennas Propag., vol. 65, no. 6,
pp. 3024–3032, Jun. 2017.
ZHENGLONG WANG was born in Anhui, China,
[16] X. Yang, S. H. Xu, F. Yang, and M. K. Li, ‘‘A novel 2-bit reconfigurable
in 1993. He received the B.E. degree in elec-
reflectarray element for both linear and circular polarizations,’’ in Proc.
IEEE Int. Symp. Antennas Propag. USNC/URSI Nat. Radio Sci. Meeting, tronic information engineering from Hefei Nor-
Jul. 2017, pp. 2083–2084. mal University, China, in 2017. He is currently
[17] X. Chen and Y. Ge, ‘‘A 14 × 14 electronically reconfigurable reflectarray pursuing the M.E. degree in electromagnetic field
using 1-bit reflective element,’’ in IEEE MTT-S Int. Wireless Symp. Dig., and microwave technology with Huaqiao Univer-
Chengdu, China, May 2018, pp. 1–3. sity, Xiamen, China. His current research interests
[18] W. Pan, C. Huang, X. Ma, and X. Luo, ‘‘An amplifying tunable transmitar- include reconfigurable antennas, reflectarrays, and
ray element,’’ IEEE Antennas Wireless Propag. Lett., vol. 13, pp. 702–705, transmitarrays.
2014.
[19] A. Clemente, L. Dussopt, R. Sauleau, P. Potier, and P. Pouliguen,
‘‘Wideband 400-element electronically reconfigurable transmitarray in
X band,’’ IEEE Trans. Antennas Propag., vol. 61, no. 10, pp. 5017–5027,
Oct. 2013.
YUEHE GE (S’99–M’02) received the Ph.D.
[20] M. Wang, S. H. Xu, F. Yang, and M. K. Li, ‘‘Design of a Ku-band 1-bit
reconfigurable transmitarray with 16 × 16 slot coupled elements,’’ in Proc. degree in electronic engineering from Macquarie
IEEE Int. Symp. Antennas Propag. USNC/URSI Nat. Radio Sci. Meeting, University, Sydney, Australia, in 2003.
Jul. 2017, pp. 1991–1992. From 1991 to 1999, he was an Antenna Engineer
[21] L. D. Palma, A. Clemente, L. Dussopt, R. Sauleau, P. Potier, and with the Nanjing Marine Radar Institute, China.
P. Pouliguen, ‘‘Circularly-polarized reconfigurable transmitarray in Ka- From 2002 to 2011, he was a Research Fellow with
band with beam scanning and polarization switching capabilities,’’ IEEE the Department of Electronic Engineering, Mac-
Trans. Antennas Propag., vol. 65, no. 2, pp. 529–540, Feb. 2017. quarie University, Australia. Since 2011, he has
[22] P. W. Hannan and M. A. Balfour, ‘‘Simulation of a phased-array antenna in been a Professor with Huaqiao University, China.
waveguide,’’ IEEE Trans. Antennas Propag., vol. 13, no. 3, pp. 342–353, His research interests include antenna theory and
May 1965. designs for radar and communication applications, computational electro-
[23] N. Lenin and P. H. Rao, ‘‘Evaluation of the reflected phase of a patch using magnetics and optimization methods, and metamaterials and metasurfaces as
waveguide simulator for reflectarray design,’’ Microw. Opt. Technol. Lett., well as their applications. He has authored and coauthored over 180 journal
vol. 45, no. 6, pp. 528–531, Jun. 2005. and conference publications and two book chapters. He is a member of the
IEICE and ACES. He received several prestigious prizes from the China State
Shipbuilding Corporation and the China Ship Research and Development
Academy, due to his contributions to China State research projects. He has
received 2000 IEEE MTT-S Graduate Fellowship Awards and the 2002 Max
Symons Memorial Prize of the IEEE NSW Section, Australia, for the Best
Student Paper. He is the co-winner of the 2004 Macquarie University Inno-
vation Awards-Invention Disclosure Award. He has served as a Technical
Reviewer for over 10 international journals and conferences.

JIXIONG PU received the B.S. degree in physics

HAI ZHANG received the B.E. degree in and the M.S. degree in optics from Fujian Nor-
electronic information engineering from North- mal University, China, in 1983 and 1986, respec-
west Polytechnical University, in 2003, and the tively. Since 1986, he has been a Faculty Member
M.E. and Ph.D. degrees in electronic science with Huaqiao University, China. He became a Full
and technology from Xi’an Jiaotong University, Professor, in 1999. He visited the University of
in 2006 and 2010, respectively. Since 2010, he Tsukuba, Japan, from 1998 to 1999, and as a vis-
has been with the School of Information Science iting scholar and JSPS Fellow, from 2001 to 2002.
and Engineering, Huaqiao University. His current His main research interests are propagation and
research interests involve high power microwave focusing of laser beams, modulation of the light
and millimeter-wave techniques, terahertz tech- field, and nonlinear optics.
niques, plasma physics, and antenna design.

VOLUME 7, 2019 66575