weberpremix

SP-11
One coat high bonding ready
mix plaster

Plastering
Mortars

Leb Egypt Jordan UAE Qatar Kuwait KSA Oman Mixing ratio 7-9 liters per 50kg bag
50kg 50kg 50kg 50kg 50kg 50kg 50kg 50kg Density 1.60 ± 0.1
Pot life <2 hours @20°C
VOC as per method less than 1 g/LT
PRODUCT USEPA method 24
weberpremix SP-11 is a cementitious fibre reinforced ready
mix plaster used for traditional plastering works in a clean and Resistance to fire as per Class A1
BS EN 998 -1
speedy manner, while keeping a homogeneous mix. Due to its
high content in additives, it allows better shrinkage control as Compressive strength ≥ 4 MPa
well as improved workability, bonding and curing. at 28 days - EN 1504 -11
weberpremix SP-11 is recommended for external and internal Adhesion strength test at > 0.35 Mpa
plastering on block walls, ceilings, concrete surfaces, bricks 28 days
and for general filling up. BS EN 1015-12
weberpremix SP-11 can be applied traditionally by hand or by *Tests done at 14 % water and performed under laboratory
using modern plaster-spraying machines. conditions.
It should not be used on painted surfaces or floors.
For the application on Light Weight concrete blocks, it is APPLICABLE STANDARDS
recommended to use weberpremix SP-3 FL or weberpremix BS EN 1015-12
SP 33. BS 8481
BS 4551: Part 2
CHARACTERISTICS BS 1881: Part 207
Color Grey ASTM C 150
ASTM C 926
Composition Portland cement, selected
ASTM C 897
sand, selective additives
EN 13914-1
including powder polymers
EN 13914-2
Grain size Up to 3mm

1/2 Technical data sheet • Edition: 01.24 • www.middleeast.weber

INSTRUCTIONS FOR USE without guarantee since the conditions of their application
SUBSTRATE PREPARATION are beyond its control. It is recommended to verify with the
All bases should be sufficiently rigid, clean of any surface company that the product is suitable for the intended use, and
contamination that may prevent good suction. that this Data Sheet version is the latest one. The company may
Although weberpremix SP-11 can be applied directly over modify it without prior notice. Technical characteristics are
masonry blocks. Smooth concrete surfaces, or those with low listed for guidance only. For more information, please contact
absorption, can be made more receptive to plaster application the company’s office in your location.
by first applying a spatter dash slurry coat (weberpremix SRC-
2 or SRC-S) as a key coat for improved bonding & adhesion of NOTE
subsequent layers. The information included on this Technical Data Sheet is the
A few hours before the application of weberpremix SP-11, sole property of Saint-Gobain Middle East Holding SAL (previ-
dampen the substrate with clean water. ously SODAMCO Holding). The unauthorized disclosure, use,
dissemination or copying (either whole or partial) of this data
PRODUCT PREPARATION sheet or any information it contains, is prohibited and subject
Mix manually or mechanically a 50 kg bag of weberpremix SP- to legal pursuit.
11 with 7 to 9 litres of clean water until a homogeneous paste is
obtained. Let the mix rest for a few minutes.
If a spraying machine is used, the mixing is carried out
automatically.

PRODUCT APPLICATION
Apply the plaster on the prepared surface by spraying it or
manually with a plastering trowel at a thickness between 10
and 20 mm in one layer.
Finish the surface with a wooden or steel float as required.
Ideal application temperature is between +5°C to +35°C. If the
temperature is higher then 35°C, make sure to use cool water
when mixing to keep the mixed material below 30°C.
Let the product set properly on the surface before any curing.
If more thickness is required, the application should be done in
two layers. The 1st layer should be roughened then cured. The
2nd layer should be applied at least 48 hrs after the 1st one.

CURING
Protect the newly applied plaster from sunshine and wind.
The new plaster has to be cured with water for at least three
days by spraying 3 to 4 times daily.

CONSUMPTION
Approximately 1.6 kg per m2 per 1 mm thickness.

STORAGE
12 months after manufacturing date in original and non-open
packaging, under cover, in dry condition, away from humidity,
protected from extreme temperatures and direct sunlight.

SAFETY PRECAUTIONS
The product contains cement powders which, when mixed
with water, release alkalis that could be harmful to the skin. It
is preferable that the application be done in a ventilated area,
and to wear protective gear for hands, eyes and respiratory
system and to avoid breathing of the dust. Splashes on the skin
should be washed away by cleaning with soap and water. In
case of contact with eyes, wash thoroughly with clean water. If
swallowed, do not induce vomiting, in both cases seek medical
attention. The product is non-flammable.

DISCLAIMER
While the company guarantees its products against defective
materials, the use and application of these products are made

2/2 Technical data sheet • Edition: 01.24 • www.middleeast.weber