Scribd
Upload
27 views4 pages

WP Lower Ethernet Cost With Daisy Chain

The document discusses using Ethernet in a daisy chain topology to reduce costs compared to a star topology using switches. A daisy chain topology connects devices in series using just Ethernet cable, without additional switches. This lowers infrastructure costs and makes installation easier. It also provides redundancy using RSTP to automatically route around failures within 100ms to 1 second.

Uploaded by

Nándor Zámbó
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
27 views4 pages

WP Lower Ethernet Cost With Daisy Chain

The document discusses using Ethernet in a daisy chain topology to reduce costs compared to a star topology using switches. A daisy chain topology connects devices in series using just Ethernet cable, without additional switches. This lowers infrastructure costs and makes installation easier. It also provides redundancy using RSTP to automatically route around failures within 100ms to 1 second.

Uploaded by

Nándor Zámbó
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Reduce Ethernet Connected Cost with Daisy Chain

by: Michael Roche, Principle Network Applications Engineer, Schneider Electric

Many older automation fieldbus networks use a form of daisy chain topology. Daisy chain topology
consists of a cable acting as a physical bus with taps or connectors installed close to the
equipment location. The benefits are several: little to no infrastructure costs beyond the
connectors, and installation flexibility as the cable can be easily routed from one device to the next.
While Ethernet has enjoyed widespread adoption and vendor support in industry, there are
attributes of Ethernet which make it more costly to deploy as compared to this legacy fieldbus
design.

Ethernet networks require infrastructure equipment like hubs and switches. Switches introduce a
per port cost that increases the overall cost of the installation. Adding to this cost are unused ports
on Ethernet switches. While it may be prudent to order switches with extra ports, the effect is an
increase in the initial cost of the network. Difficulty planning for future port requirements adds to
the problem.

Ethernet also imposes distance constraints which require careful planning to efficiently locate
switches. End devices typically use RJ45 Category 5 cable which must be located within 100
meters of the switch port.

An example of the difficulty of implementing Ethernet in bus applications is illustrated by a


conveying application depicted in Figure 1. This conveying application uses a star topology.
There may be
relatively few switch
ports used within a
100 meter radius,
and a separate
media segment is
required to each
device, even if the
devices are 1 meter
apart. Inefficient
utilization of
switches and switch ports adds to the overall installation cost. Further, inter switch link distances
can exceed 100 meters requiring fiber optic media. Switches with fiber optic ports are
correspondingly more expensive, as is the fiber media itself.
A daisy chain Ethernet topology addresses all of these issues, offering many of the benefits found
in the earlier fieldbus’.
What is Daisy Chain Ethernet?

As shown in Figure 2, a daisy chain device has 2 embedded Ethernet ports which function as an
Ethernet switch, as well as an interface to the local device. This allows information to flow to the
device, or flow through the ports to other devices in the daisy chain.

Ethernet Daisy Chain allows devices to be cabled together in series using standard Ethernet
cable, similar to legacy fieldbus’ without the need for additional Ethernet switches. Cabling
devices in
series permits
flexibility
locating
devices, eases
installation, and
lowers
infrastructure
costs. Point-to-
point cable
routing flexibility
along with
reduced
installation costs
offer a significant advantage over the costs and design constraints of a traditional star based
Ethernet topology.

While daisy chain can be deployed in a straight line bus topology, having a redundant ring daisy
chain offers fast recovery in the event of a cable break. Simply adding a single switch with
redundant capability connects the daisy chain to the overall network and affords robust
redundancy.

Choose a switch, available from many vendors, offering redundancy with fast recovery using the
Rapid Spanning Tree Protocol (RSTP). RSTP is the IEEE 802.1w redundancy standard
interoperable with switches from many OEM’s. RSTP not only restores communications in the
event of media disconnect or failure, it protects against accidental cabling loops which can cause
non-RSTP networks to fail. Daisy chain RSTP monitors the health of the physical ring while
blocking traffic to prevent a traffic loop. Should RSTP detect a failure in the ring, RSTP will recover
and rebuild the network automatically to divert traffic around the failure.

Consider the same conveying application discussed earlier fitted with daisy chain Ethernet instead
of a switch based star topology as shown in Figure 3. Message traffic between the PLC and end
devices can be any standard 802.3 Ethernet protocol, from any automation OEM.

Note that there is


an overall
efficiency gained
by having fewer
Ethernet
switches, less
Ethernet media,
and increased
redundancy in
the event of a
media or device failure. RSTP will send health messages around the ring to verify that the ring is
intact. Should a message not be received, each device, including the switch, will exchange
information to determine where the media failure occurred. The devices will then rebuild the
network to route messages around the fault, as shown in Figure 4.

Once a media break or device failure in the network is detected, the Ethernet devices and the
switch work
together to
reconstruct new
message
forwarding tables
around the fault.
The standby link
will begin
forwarding traffic
around the problem
segment and
restore network
communications.
The total time from when the media fault occurs, until the time traffic begins flowing again ranges
from under 100 milliseconds to less than 1 second depending on the switch RSTP capability. The
entire fault detection and recovery effort is automatic. When the fault is repaired, the daisy chain
RSTP will detect the change and restore the original configuration.

How many devices can be part of a daisy chain?

Up to 32 devices in a daisy chain can be sensibly deployed in an industrial setting. Theoretically


there could be dozens of device deployed in a daisy chain because of store and forward
technology. Daisy chain devices, like and Ethernet switch, use store and forward technology. This
assures that each packet is checked for accuracy before being forwarded on the network. The cost
of that accuracy is 20-40 microseconds latency for an average automation protocol message
passing through each device.

This means that the total time it takes for a message to travel from the first device in the daisy
chain to the last device, with 32 daisy chain devices and ‘worst case’ 40 microsecond latency for
each device is less than 1.3 milliseconds.

Benefits of Ethernet daisy chain:


• Reduced cost per connection
• Lower infrastructure and media costs
• Device cable location flexibility
• Increased redundancy over Ethernet switched start topology
• Software configuration is optional but not required
• Simple, familiar installation
• Reduced cabinet footprint without additional switches
• Robust media redundancy
• Ease of maintenance

Daisy chain Ethernet offers the best of both worlds. Simple installation and setup with the
robustness of the Ethernet protocol marries together 21st century technology with the simplicity of
earlier fieldbus’. Daisy chain Ethernet is also not restricted to any single vendor or organizational
protocol. ModbusTCP, Profinet, and ODVA EtherNet/IP all work well, even together, in a daisy
chain topology. This allows end users to mix devices, even using different protocols, in a single
daisy chain for maximum convenience.

Automatic fault detection and recovery also allows individual devices to be taken offline and
restored for service without significant interruption to other devices. Taken together, lower costs,
easier installation, design flexibility and range, daisy chain Ethernet is an attractive evolution of the
industrial fieldbus.

For further information please contact Michael B. Roche, Principal Network Application Engineer

You might also like