Chapter 3: Current and Resistance.

Direct
Current Circuits

3.1. Electric Current

3.2. Resistance and Resistivity

3.3. Ohm’s Law and a Microscopic View of Ohm’s Law

3.4. Semiconductors and Superconductors

3.5. Work, Energy, and Emf

3.6. Kirchhoff’s Rules
3.7. Resistors in Series and in Parallel
3.8. RC Circuits
3.5. Work, Energy, and Emf
3.5.1. Concepts:
• To make charge carriers flow through a device we must establish
a potential difference between the ends of the device, e.g.,
connecting the device to a charged capacitor but the duration time
is very short
• To produce a steady flow, we need a charge pump, an emf
device  (emf: electromotive force, outdated phrase)
• Some examples for emf devices: battery, electric generators
(solar cells, fuel cells, thermopiles), living systems (electric eels)
• When an emf is connected (in a closed circuit), within the emf
device, positive charge carriers move from a region of low electric
potential (low electric potential energy, negative terminal) to a
region of higher potential (higher potential energy, positive
terminal)

• This flow of positive charge and the

current have the same direction

• As this motion is the opposite

of what the electric field between
the terminals would cause the
positive charges to move, therefore
there must be a energy source to
do work on the charges

• The source may be chemical, or involves

mechanical forces, temperature differences,
or the Sun
3.5.2. Work, Energy, and Emf:
Emf :
• We analyze a circuit as shown: in any
time interval dt, a charge dq passes
through any cross section of the circuit
• The emf device does an amount of
work dW:, we define the emf of the
emf device as follows:

dW

dq
• So, the emf of an emf device is the work per unit charge that
the device does in moving charge from its low-potential
terminal to its high-potential terminal (symbol: )
• SI unit: 1 Volt (V) = 1 Joule / 1 Coulomb
•An ideal emf device: the potential difference between the
terminals is equal to the emf of the device (no internal resistance
r = 0), V =  (open or closed circuit)
• A real emf device: V =  if there is no current
through the device and V <  if there is a current,
it means the real devices have internal resistance
(r  0)

Power of an emf device:

dW  dq  idt  Pdt
P  i A real emf device
3.6. Kirchhoff’s Rules
3.6.1. Loop Rule (Voltage Law): The algebraic sum of the
changes in potential encountered in a complete traversal of any
loop of a circuit must be zero
Example: We consider a circuit as
shown, from point a we follow the
clockwise direction, we have:

  iR  0
Important Notes:
• For a move through a resistance in the direction of the current,
the change in potential is –iR; in the opposite direction it is +iR
(resistance rule)
• For a move through an ideal emf device in the direction of the
emf arrow, the change in potential is +; in the opposite direction
it is - (emf rule)
•If you follow the counterclockwise
direction:

iR    0

Checkpoint: The figure shows the current i in a single-loop circuit

with a battery B and a resistance R (and wires of negligible
resistance). (a) Should the emf arrow at B be drawn pointing
leftward or rightward? At points a, b, and c, rank (b) the
magnitude of the current, (c) the electric potential, and (d) the
electric potential energy of the charge carriers, greatest first.

(a) rightward
(b) all tie
(c) Vb, Va=Vc
(d) b, a=c - +
3.6.2. Junction Rule (Current Law): The sum of the currents
entering any junction must be equal to the sum of the currents
leaving that junction

i1  i2  i3
This rule is a statement of the conservation
of charge for a steady flow of charge, there
is neither a buildup nor a depletion of charge
at a junction
3.7. Resistors in Series and in Parallel:
In this section, we study resistances in series and in parallel
using Kirchhoff’s rules. First, we apply the rules for a single-loop
circuit
3.7.1. A single-loop circuit:
Internal Resistance:
 A real battery has internal
resistance r
Using the loop rule clockwise
beginning at point a:

Vb  Va  Vd  Vc  0
As the battery has a resistance r: Vb  Va    ir
(  ir )  (iR)  0

So, we can calculate the current i: i
rR
 The changes in electric potential around the circuit

Note: in general, if a battery is not described as real or if no

internal resistance is indicated, you can assume that it is ideal
3.7.2. Multiloop circuits:
Example: The figure shows a
multiloop circuit consisting of
three branches
Junction rule for point b:
i1  i3  i2 (1)
Applying the loop rule for
left-hand loop badb in a
counter-clockwise direction:

1  i1R1  i3R3  0 (2)

For right-hand loop bdcb: i3 R3  i2 R2   2  0 (3)
For big loop badcb: 1  i1R1  i2 R2   2  0 (4)
Note: Equation (4) can be derived from the sum of (2) and (3), so
we can use only two of the three equations above for such a
multiloop circuit
3.7.3. Resistors in Series:
Problem: Calculate the resistance of resistors connected in series

We apply the Kirchhoff’s rules in the

clockwise direction:
• Junction Rule: When a potential difference
V is applied across resistances connected
in series, the resistances have identical
currents i:
i  i1  i2  i3
• Loop Rule: The sum of the potential
differences across resistances is equal to
the applied potential difference V:

  iR1  iR2  iR3  0


i
R1  R2  R3
• If we replace three resistors by an
equivalent resistor, so its resistance is:

  iReq  0
Req  R1  R2  R3
• For n resistors connected in series:

n
Req  Rj
j 1
3.7.4. Resistors in Parallel:
Problem: Calculate the resistance of resistors connected in parallel
For resistors in parallel:
When a potential difference V is applied
across resistances connected in parallel,
the resistances all have that same potential
difference V.
• Junction Rule: i  i1  i2  i3
 1 1 1 
i  V    
 R1 R 2 R3 
• Loop Rule: If we replace three resistors by
an equivalent resistor:
  iReq  0
if n resistors in parallel:
1 1 1 1
   n

1 1
Req R1 R 2 R3 
Req R
j 1 j
Series and Parallel Resistors and Capacitors

Series Parallel Series Parallel

Resistors Capacitors

n n n n
Rj   
1 1 1 1
Req    Ceq  C j
j 1
Req j 1 R j Ceq j 1 C j j 1
Same current Same Same charge Same
through all potential on all potential
resistors difference capacitors difference
across all across all
resistors capacitors
Sample Problem (p.718):Electric fish are able to generate current
with biological cells called electroplaques, which are physiological
emf devices. The electroplaques in the type of electric fish known
as a South American eel are arranged in 140 rows, each row
stretching horizontally along the body and each containing 5000
electroplaques. The arrangement is suggested in Figure a; each
electroplaque has an emf  of 0.15 V and an internal resistance r
of 0.25 . The water surrounding the eel completes a circuit
between the two ends of the electroplaque array, one end
at the animal's head and the other near its tail.

(a) If the water surrounding the eel has resistance Rw = 800 ,

how much current can the eel produce in the water?

To solve this problem, we can simply the circuit of Figure a by

replacing combinations of emfs and internal resistances with
equivalent emfs and resistances as shown in the following figures
b, c, and d:
0.15 V 0.15 V

140

1 1 1
  140
Req Rj Rrow
j 1
The equivalent resistance:
Rrow
Req   8.93()
140
Using the loop rule:

 row  iRw  iReq  0

 row 750
i   0.93( A)
Rw  Req 800  8.93
Therefore, if the head or tail of the eel is near a fish, some of
this current could pass along a narrow path through the fish,
stunning or killing the fish

(b) How much current irow travels through each row of Figure a?

i 0.927 3
irow    6.6 10 ( A)
140 140
3.7.5. Calculating Potential Difference Between Two Points:
Usually we need to calculate potential difference between two
points in a circuit. This section will show you how to do this in
some common cases and other issues related to potential
difference
• Calculate Vb-Va in the figure:
We start at point a with potential Va,
when we pass through the battery’s emf,
the potential increases by , when we pass
through the battery’s internal resistance r
the potential decreases by ir. We are then
at point b with potential Vb:

Va    ir  Vb

So: Vb  Va    ir; i
rR
 12
Vb  Va  R 4  8(V )
rR 24
Vb-Va is the terminal-to-terminal potential difference V:
Vb  Va    ir
So, for a real battery V is less 
For an ideal battery: V = 

Grounding a circuit: The figures show

point a or b directly connected to ground
(symbol: ). In this case, the potential
is defined to be zero at the grounding point
in the circuit

So, we have:
• In Figure a, Vb-Va= 8 V, Va = 0 
Vb = 8 V
• In Figure b, Vb = 0  Va = -8 V
The relationship between Power and Potential:
We will calculate work done by an emf device (e.g., a battery) on
the charges to establish a current i; the dissipation rate of
energy due to the internal resistance r of the emf device and the
power of the emf device
• The net rate P of energy transfer from the emf device to the
charge carriers:
P  iV
• We also have:
V    ir
P  i(  ir )  i  i r
2
• The term i2r is the rate of energy transfer to thermal energy
within the emf device:
2
Pr  i r
• The rate of energy transfer from the emf device both to the
charges and to the thermal energy:
Pemf  i
3.7.6. The Ammeter and the Voltmeter:

• An instrument that is used to

measure currents is called an
ammeter
• A meter to measure potential
difference is called a voltmeter

• The figure shows how to set up

an ammeter and a voltmeter in a
circuit

• A meter can measure currents

(ammeter), potential difference
(voltmeter) and resistance (ohmmeter),
by means of a switch, is called a multimeter
3.8. RC Circuits:
In this section we begin to study time-varying currents
3.8.1. Charging a Capacitor:
• An RC series circuit: a circuit consists
a capacitor C, an ideal battery and a
resistor R
• When S is closed on a, C is charged:
the charge begins to flow between the
capacitor plates and the battery
terminals, establishing a current i.
When VC = Vbattery = , the current is zero
• Now, we examine the charging process:
- charge q(t), potential difference VC(t), and current i(t).
Using the loop rule:
q
  iR  VC  0    iR   0
C
dq dq q
i R    (chargi ng equati on)
dt dt C
The solution for the differential equation above is:

t / RC
q  C (1  e )
(see text for solving the equation)
So, the current i(t):
dq    t / RC
i   e
dt  R 
And the potential difference V(t) across
the capacitor:

q t / RC
VC    (1  e )
C

Note: When the capacitor becomes fully

charged as t: q = C, i = 0, and VC = 
The time constant:   RC (Unit: s)

At t =  = RC:
1
q  C (1  e )  0.63C
During the first time , the charge increases from zero to 63% of
its final value C
The greater  is the greater the charging time

3.8.2. Discharging a Capacitor:

After being fully charged, the capacitor has a potential V0 = ,
we switch S from a to b, so the capacitor discharges through
resistor R. Using the loop rule:

dq q
R   0 (di schargi ng equati on)
dt C
The solution for this equation is:
t / RC
q  q0e
Where:
q0  CV0
1
q
At t =  = RC, the charge is reduced to 0 e or about 37% of
the initial value

The current i(t): dq  q0  t / RC

i   e
dt  RC 
The potential difference VC(t):

t / RC
VC  V0e
Checkpoint: (Cap-monster maze) All the capacitors have a
capacitance of 6 F, and all the batteries have an emf of 10 V.
What is the charge on capacitor C?

   0  q  C  6 10 6 10  60 10 6 (C )  60( C )

q
C
Checkpoint: (Res-monster maze) All the resistors have a
resistance of 4 , and all the batteries have an emf of 4 V.
What is the current through resistor R?

iR          0  i  2 / R  2( A)

Homework: 2, 5, 7, 10, 17, 22, 24, 30, 34, 44, 45, 54,
57, 60, 65 (pages 726-731)