HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL
ORIGINAL MANUAL ISSUE DATE: 7/2015
GN1T CHASSIS
Segment: XFLL
Version Date Subject
1.0 7/2015 Original manual issue.

LCD TV

9-888-581-01
SERVICE MANUAL
GN1T CHASSIS
Segment: XFLL

LCD TV

9-888-581-01
MODEL LIST

MODEL COLOR COMMANDER DEST. MODEL COLOR COMMANDER DEST.

KD-49X8005C Black RMT-TX100B (BR6) XBR-65X800C Black RMT-TX100B (LA1)
BRAZIL MEXICO
XBR-65X805C Black RMT-TX100B (LA8)
KD-55X8005C Black RMT-TX100B (BR6) CHILE
BRAZIL PERU
VENEZUELA
XBR-65X807C Black RMT-TX100B (CO1)
XBR-55X805C Black RMT-TX100B (LA8)
CHILE COLOMBIA
PERU XBR-65X809C Black RMT-TX100B (ECU)
VENEZUELA ECUADOR
(AR4) XBR-65X810C Black RMT-TX100U (UC2)
ARGENTINA US/CND
XBR-55X807C Black RMT-TX100B (CO1)
COLOMBIA
XBR-55X809C Black RMT-TX100B (ECU)
ECUADOR
XBR-55X810C Black RMT-TX100U (UC2)
US/CND

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 3
WARNINGS AND CAUTIONS - ENGLISH

CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power line.

CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.

SAFETY-RELATED COMPONENT WARNING!!

Components identified by shading and mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony
parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Follow these procedures whenever critical components are replaced or improper operation is suspected.

CAUTION ABOUT THE LITHIUM BATTERY

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Outer case broken battery should not contact to water.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 4
WARNINGS AND CAUTIONS - FRENCH

ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement.
Pour prévenir le risque de choc électrique, ne pas faire l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é faire ainsi.

WARNING!!
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout dépannage. Le chássis de ce récepteur est
directement raccordé à l’alimentation du secteur.

POUR TRANSPORTER LE TÉLÉVISEUR

Tenez compte de ce qui suit pendant l’installation du téléviseur :
• Débranchez tous les câbles avant de transporter le téléviseur.
• Transportez le téléviseur avec le nombre de personnes approprié ; un téléviseur de grande taille doit être transporté par au moins deux personnes.
• Lors du transport du téléviseur, l’emplacement des mains est très important pour votre sécurité, ainsi que pour éviter de causer des dommages.

ALERTE!!
Afi n d’eviter tout risque d’electrocution provenant d’un chassis sous tension, un transformateur d’isolement doit etre utilise lors de tout depannage. Le chassis de ce recepteur est
directement raccorde a l’alimentation du secteur.

ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!

Les composants identifi es par une trame et par une marque sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite
du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les
reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de
composants critiques, ou lorsqu’un mauvais fonctionnement suspecte.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 5
 WARNINGS AND CAUTIONS

USE CAUTION WHEN HANDLING THE LCD PANEL

When repairing the LCD panel, be sure you are grounded by using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.

1) Do not press on the panel or frame edge to avoid the risk of electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within the module.
6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 6
SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.

7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 7
 SAFETY CHECK-OUT

Leakage Test
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’
instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The
“limit” indication is 0.75 V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all
battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).

How to Find a Good Earth Ground

A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also
at earth ground.
If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance
between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot
side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the
lamp should light at normal brilliance if the screw is at ground potential (see Figure B).

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 8
SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.

DIAGNOSTIC TEST INDICATORS

When an error occurs, the Smart Core Red LED will flash a set number of times to indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .

<G>: Power supply board, <B>: Main board, <T>: Tcon board, (LD) board ,
<P>: Panel module , <S>: Speaker , <A>: Power Adapter

RED LED blinking count Detection Items

2x <G/B> Main 12V over voltage [MAIN_POWER]

<B> Main 5.0V failure [DC_ALERT]

<B/S> Audio amp. protection [AUD_ERR]

<B> Tuner or demodulator I2C No ACK [TU_DEMOD] [Note.1]
3x
<B> HDMI Switch/Equalizer I2C communication error [HDMI_EQ] [Note.2]

Note.1/Note.2: Both functions were disabled but remains on the Self diagnosis screen like in the next page.
Note.2: There are some sets which still enable this HDMI error detection function.
Among these, software version updated or installed to PKG2173 or higher have this function disabled.

<LD/P> LED driver failure/LED voltage protection [LD_ERR]

4x
<LD/P> Error detection of the I2C communication between the Main device and the LD IC.[BCM_ERR]

<P/T/G/B> Panel ID EEPROM I2C No ACK (Also panel power failure is a suspect) [P_ID_ERR]
5x
<T> TCon IC I2C communication error [TCON_ERR]

6x <G/P/B> Backlight failure [BACKLIGHT]

Over temperature protection [TEMP_ERR]

7x <B> Temp. sensor I2C No ACK [TEMP_ERR]
<B> V By One lock error between Main device and 4KBE device [4KBE_ERR]

8x <B> Software error [SW_ERR]

Red italic: detect at startup sequence only.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 9
 SELF DIAGNOSIS FUNCTION

[SELF DIAGNOSTIC SCREEN DISPLAY]

Error count
Error item Naming

Format of error timestamps SELF CHECK

YYMMDDhhmmss (in UTC)
Example: Back
120823132523 -> Aug 23 2012 13:25:23 UTC
<<
* Only when time is set, an error timestamp 002 MAIN_POWER 000000000000 000000000000 000000000000 000
is saved. 003 DC_ALERT 000000000000 000000000000 000000000000 000
003 AUD_ERR 150101000018 150101000018 150101000018 003
Both of HDMI_EQ/TU_DEMOD have been disabled. 003 HDMI_EQ 150101000123 150101000045 150101000045 003
(Refer the previous page for details.) 003 TU_DEMOD 150101000218 150101000223 150101000105 003
004 LD_ERR 000000000000 000000000000 000000000000 000
004 BCM_ERR 000000000000 000000000000 000000000000 000
005 TCON_ERR 150101000504 000000000000 000000000000 001
005 P_ID_ERR 000000000000 000000000000 000000000000 000
Smart Core Red LED
blinking count 006 BACKLIGHT ERR 000000000000 000000000000 000000000000 000
007 TEMP_ERR 150101000200 150101000002 000000000000 002
007 4KBE_ERR 000000000000 000000000000 000000000000 000
008 SW_ERR 000000000000 000000000000 000000000000 000

00005 00414 00002

•Panel Operation Time is recorded every [Home]Exit
30 min, but Total Operation Time is recorded every 1 hr.
Therefore, the panel op. time might become larger than Error Error Error
the total op. time. timestamp for timestamp for timestamp
last recorded second last for 3rd last
error recorded error recorded
error

Total Operation Time [hr] – Boot Count – Panel Operation Time [hr]

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 10
 SELF DIAGNOSIS FUNCTION

SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for
confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.
After you have completed the repairs, clear the result display to “0”.

Clearing the Self Check Diagnostic List

Panel operation time : Press the Channel 7 => Channel 0 .

Exiting the Self-diagnostic screen

To exit the Self Diagnostic screen, Power off & on or Push the <Home> button.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 11
SEC 1. DISASSEMBLY
• There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts.
1-1. KD-49X8005C
1-1-1. STAND AND NECK

4 screws (SCREW, +PSW M5X12) P/N: 2-580-607-01 STAND

Screw (SCREW, +PSW M5X12)

P/N: 2-580-607-01 Screw (SCREW, +PSW M5X12)
P/N: 2-580-607-01

NECK
NECK

STAND, SHAFT
(L SWN) A

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 12
 DISASSEMBLY

1-1. KD-49X8005C
1-1-2. LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (W)

LABEL, SIDE TERMINAL (W)

LABEL, REAR TERMINAL

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 13
 DISASSEMBLY

1-1. KD-49X8005C
1-1-3. AC COVER AND POWER SUPPLY CORD

Screw (SCREW, +PSW M4X10) P/N: 4-159-298-01

2 3 4 POWER SUPPLY CORD 5

AC COVER

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 14
 DISASSEMBLY

1-1. KD-49X8005C
1-1-4. COVER, REAR (M SWN) A

1 2

7 screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: 2-580-639-01

6 screws (SCREW, +PSW M4X10) P/N: 4-159-298-01
10 screws (SCREW, +PWH M3X6) P/N: 4-452-935-11

3
COVER, REAR (M SWN) A NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 15
 DISASSEMBLY

1-1. KD-49X8005C
1-1-5. TAPE

TAPE

TAPE

TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 16
 DISASSEMBLY

1-1. KD-49X8005C
1-1-6. TAPE AND WIRE DRESSING

1 2

TAPE
TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 17
 DISASSEMBLY

1-1. KD-49X8005C
1-1-7. WIRE DRESSING AND SPEAKER BOX ASSY (L)

1 2 3

4 5 6

SPEAKER BOX ASSY (L)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 18
 DISASSEMBLY

1-1. KD-49X8005C
1-1-8. WIRE DRESSING AND SPEAKER BOX ASSY (R)

1 2

3 4 5

SPEAKER BOX ASSY (R)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 19
 DISASSEMBLY

1-1. KD-49X8005C
1-1-9. TAPE

TAPE
TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 20
 DISASSEMBLY

1-1. KD-49X8005C
1-1-10. CONNECTOR ASSY 28P

CONNECTOR ASSY 28P

2 3 P/N: 1-910-110-70

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 21
 DISASSEMBLY

1-1. KD-49X8005C
1-1-11. TAPE AND FLEXIBLE FLAT CABLE 51P (XFC)

TAPE

2 3
FLEXIBLE FLAT CABLE 51P (XFC)
P/N: 1-849-080-11

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 22
 DISASSEMBLY

1-1. KD-49X8005C
1-1-12. WIRE DRESSING

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 23
 DISASSEMBLY

1-1. KD-49X8005C
1-1-13. SMART CORE

1 2
SMART CORE

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 24
 DISASSEMBLY

1-1. KD-49X8005C
1-1-14. SWITCH UNIT

2 3

SWITCH UNIT

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 25
 DISASSEMBLY

1-1. KD-49X8005C
1-1-15. HARNESS ASSY(MAIN) AND BT ANTENNA

HARNESS ASSY(MAIN)
P/N: 1-910-110-71

1 2 3
BT ANTENNA

Screw (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 26
 DISASSEMBLY

1-1. KD-49X8005C
1-1-16. BRACKET, SP L (L SWN) A AND BRACKET, SP R (L SWN) A

1 1

6 screws (SCREW, +PSW M3X8) 6 screws (SCREW, +PSW M3X8)

P/N: 2-580-593-01 P/N: 2-580-593-01

2 2

BRACKET, SP R (L SWN) A BRACKET, SP L (L SWN) A

3 3

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 27
 DISASSEMBLY

1-1. KD-49X8005C
1-1-17. BRACKET, STAND (L SWN)

BRACKET, STAND (L SWN)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 28
 DISASSEMBLY

1-1. KD-49X8005C
1-1-18. GL6

2 3 4

GL6

6 screws (SCREW, +PSW M3X6 W12) P/N: 4-256-393-12

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 29
 DISASSEMBLY

1-1. KD-49X8005C
1-1-19. SHEET, INSULATION(HRN L)
SHEET, INSULATION (HRN L)
1 2

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 30
 DISASSEMBLY

1-1. KD-49X8005C
1-1-20. BRACKET, SIDE F (MOLD)

2 3

BRACKET, SIDE F (MOLD)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 31
 DISASSEMBLY

1-1. KD-49X8005C
1-1-21. BMFW

8 screws (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41
2 3

BMFW

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 32
 DISASSEMBLY

1-1. KD-49X8005C
1-1-22. GASKET (BMF)

BMFW B-Side view Five attachment positions of Gasket

PWB P/N indication location

NOTE:
When you replace a BMFW board, it is necessary to stick five new GASKET on a new BMFW board.
GASKET (BMF): 4-566-117-01

However, please confirm PWB P/N before that.

If the PWB P/N is old type(1-894-595-11/21), need gaskets.
If the PWB P/N is new type(suffix -12/22 or later), no need gaskets.
*There is no problem even if you were mounting a gasket on new type(suffix -12/22 or later).

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 33
 DISASSEMBLY

1-1. KD-49X8005C
1-1-23. SHEET, THERMAL(BM) AND PLATE, MAIN S (HRN)

1
NOTE:

SHEET, THERMAL (BM)

2 3 4

PLATE, MAIN S (HRN)

2 screws (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 34
 DISASSEMBLY

1-1. KD-49X8005C
1-1-24. PLATE, MAIN S (SWN) AND SLIDE, CLAMP

1 2

3 screws (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41

SLIDE, CLAMP

PLATE, MAIN S (SWN)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 35
 DISASSEMBLY

1-1. KD-49X8005C
1-1-25. LCD PANEL

LCD PANEL

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 36
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-1. STAND AND NECK

4 screws (SCREW, +PSW M5X12) P/N: 2-580-607-01 STAND

Screw (SCREW, +PSW M5X12)

P/N: 2-580-607-01 Screw (SCREW, +PSW M5X12)
P/N: 2-580-607-01

NECK
NECK

STAND, SHAFT
(L SWN) A

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 37
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-2. LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (W) AND LABEL, CI

(CO1 ONLY)

LABEL, CI

LABEL, REAR TERMINAL

LABEL, SIDE TERMINAL (W)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 38
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-3. AC COVER AND POWER SUPPLY CORD

Screw (SCREW, +PSW M4X10) P/N: 4-159-298-01

2 3 4 POWER SUPPLY CORD 5

AC COVER

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 39
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-4. COVER, REAR (L SWN) A

1 2

7 screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: 2-580-639-01

6 screws (SCREW, +PSW M4X10) P/N: 4-159-298-01
10 screws (SCREW, +PWH M3X6) P/N: 4-452-935-11

NOTE:
3

COVER, REAR (L SWN) A

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 40
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-5. TAPE

TAPE

(120 Hz)

TAPE

(60 Hz)

TAPE

TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 41
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-6. TAPE

(120 Hz)

TAPE

(60 Hz)

TAPE

TAPE
TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 42
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-7. TAPE AND WIRE DRESSING

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 43
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-8. WIRE DRESSING AND SPEAKER BOX ASSY (L)

1 2

3 4 5

SPEAKER BOX ASSY (L)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 44
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-9. WIRE DRESSING AND SPEAKER BOX ASSY (R)

2 3 4
SPEAKER BOX ASSY (R)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 45
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-10. TAPE

TAPE

TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 46
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-11. CONNECTOR ASSY 28P (120 Hz)

2 3
CONNECTOR ASSY 28P
P/N: 1-910-110-69

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 47
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-12. CONNECTOR ASSY 28P (60 Hz)

2 3 CONNECTOR ASSY 28P

P/N: 1-910-110-67

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 48
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-13. FLEXIBLE FLAT CABLE 41P (120 Hz ONLY)
1
TAPE

TAPE

3 4
FLEXIBLE FLAT CABLE 41P
P/N: 1-849-076-11

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 49
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-14. FLEXIBLE FLAT CABLE 51P (120 Hz)

2 FLEXIBLE FLAT CABLE 51P

P/N: 1-849-075-11

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 50
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-15. FLEXIBLE FLAT CABLE 51P (60 Hz)

TAPE

2 3

FLEXIBLE FLAT CABLE 51P

P/N: 1-849-075-11

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 51
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-16. WIRE DRESSING

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 52
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-17. SMART CORE

1 2
SMART CORE

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 53
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-18. SWITCH UNIT

2 3

SWITCH UNIT

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 54
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-19. HARNESS ASSY (MAIN)

HARNESS ASSY(MAIN)
P/N: 1-910-110-68

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 55
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-20. BT ANTENNA

Screw (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3 BT ANTENNA

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 56
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-21. BRACKET, SP L (L SWN) A AND BRACKET, SP R (L SWN) A

1 1

6 screws (SCREW, +PSW M3X8) 6 screws (SCREW, +PSW M3X8)

P/N: 2-580-593-01 P/N: 2-580-593-01

2 2

3
3

BRACKET, SP L (L SWN) A
BRACKET, SP R (L SWN) A

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 57
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-22. BRACKET, STAND (L SWN)

BRACKET, STAND (L SWN)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 58
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-23. GL6

2 3 4

GL6

6 screws (SCREW, +PSW M3X6 W12) P/N: 4-256-393-12

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 59
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-24. SHEET, INSULATION(HRN L)
SHEET, INSULATION(HRN L)
1 2

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 60
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-25. BRACKET, SIDE F (MOLD)

2 3

BRACKET, SIDE F (MOLD)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 61
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-26. BRACKET, TOP FL (MOLD) (CO1 ONLY)

2 3

BRACKET, TOP FL (MOLD)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 62
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-27. BMFW

8 screws (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41
2 3

BMFW

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 63
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-28. GASKET (BMF)

BMFW B-Side view Five attachment positions of Gasket

PWB P/N indication location

NOTE:
When you replace a BMFW board, it is necessary to stick five new GASKET on a new BMFW board.
GASKET (BMF): 4-566-117-01

However, please confirm PWB P/N before that.

If the PWB P/N is old type(1-894-595-11/21), need gaskets.
If the PWB P/N is new type(suffix -12/22 or later), no need gaskets.
*There is no problem even if you were mounting a gasket on new type(suffix -12/22 or later).

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 64
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-29. SHEET, THERMAL(BM) AND PLATE, MAIN S (HRN)

NOTE:

SHEET, THERMAL (BM)

2 3 4

PLATE, MAIN S (HRN)

2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 65
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-30. SLIDE, CLAMP

2 SLIDE, CLAMP

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 66
 DISASSEMBLY

1-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

1-2-31. LCD PANEL

LCD PANEL

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 67
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-1. STAND AND NECK

4 screws (SCREW, +PSW M5X12) P/N: 2-580-607-01 STAND

2 screws ( SCREW, +PSW M5X20) 2 screws ( SCREW, +PSW M5X20)

NECK
NECK
STAND,
SHAFT (2L SWN) A

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 68
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-2. LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (W) AND LABEL, CI

(CO1 ONLY)

LABEL, CI

LABEL, REAR TERMINAL

LABEL, SIDE TERMINAL (W)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 69
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-3. AC COVER AND POWER SUPPLY CORD

Screw (SCREW, +PSW M4X10) P/N: 4-159-298-01

2 3 4 POWER SUPPLY CORD 5

AC COVER

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 70
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-4. COVER, REAR (2L SWN) A
COVER, REAR (2L SWN) A
1 2

7 screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: 2-580-639-01

6 screws (SCREW, +PSW M4X10) P/N: 4-159-298-01
12 screws (SCREW, +PWH M3X6) P/N: 4-452-935-11

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 71
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-5. TAPE

TAPE

TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 72
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-6. TAPE AND WIRE DRESSING

TAPE
TAPE

TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 73
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-7. TAPE

TAPE
TAPE

TAPE (DK020FR-19) 19X50 SHEET

TAPE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 74
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-8. WIRE DRESSING

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 75
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-9. SPEAKER BOX ASSY (L)

2 3

SPEAKER BOX ASSY (L)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 76
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-10. SPEAKER BOX ASSY (R)

2 3

SPEAKER BOX ASSY (R)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 77
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-11. BT ANTENNA

Screw (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3

BT ANTENNA

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 78
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-12. SMART CORE

1 2
SMART CORE

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 79
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-13. SWITCH UNIT

2 3

SWITCH UNIT

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 80
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-14. HARNESS ASSY (MAIN) AND CONNECTOR ASSY 28P

HARNESS ASSY(MAIN)
P/N: 1-910-110-66

CONNECTOR ASSY 28P

P/N: 1-910-110-65

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 81
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-15. SLIDE, CLAMP

1 2

SLIDE, CLAMP

1 2 1 2

SLIDE,
SLIDE,CLAMP
CLAMP
SLIDE, CLAMP

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 82
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-16. BRACKET, SP (2L SWN) A

1 1

4 screws (SCREW, +PSW M3X8) 4 screws (SCREW, +PSW M3X8)

P/N: 2-580-593-01 P/N: 2-580-593-01

2 2

3 3

BRACKET, SP (2L SWN) A BRACKET, SP (2L SWN) A

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 83
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-17. BRACKET, STAND (2L SWN)

PULLEY, STAND (HWI) x2

P/N: 4-534-964-01

2 3 4

BRACKET, STAND (2L SWN)

12 screws (SCREW, +PSW M3X8)
P/N: 2-580-593-01

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 84
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-18. GL6

2 3 4

GL6

6 screws (SCREW, +PSW M3X6 W12) P/N: 4-256-393-12

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 85
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-19. SHEET, INSULATION(HRN L)
SHEET, INSULATION (HRN L)
1 2

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 86
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-20. TAPE AND FLEXIBLE FLAT CABLE 41P (XFF) AND FLEXIBLE FLAT CABLE 51P (XFF)

TAPE

2 3

FLEXIBLE FLAT CABLE 51P

(XFF)
FLEXIBLE FLAT CABLE 41P (XFF) P/N: 1-849-079-11
P/N: 1-849-078-11

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 87
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-21. BRACKET, SIDE F (MOLD)

2 3

BRACKET, SIDE F (MOLD)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 88
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-22. BRACKET, TOP FL (MOLD) (CO1 ONLY)

2 3

BRACKET, TOP FL (MOLD)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 89
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-23. BMFW

8 screws (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41
2 3

BMFW

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 90
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-24. GASKET (BMF)

BMFW B-Side view Five attachment positions of Gasket

PWB P/N indication location

NOTE:
When you replace a BMFW board, it is necessary to stick five new GASKET on a new BMFW board.
GASKET (BMF): 4-566-117-01

However, please confirm PWB P/N before that.

If the PWB P/N is old type(1-894-595-11/21), need gaskets.
If the PWB P/N is new type(suffix -12/22 or later), no need gaskets.
*There is no problem even if you were mounting a gasket on new type(suffix -12/22 or later).

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 91
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-25. SHEET, THERMAL(BM) AND PLATE, MAIN S (HRN)

NOTE:

SHEET, THERMAL (BM)

2 3 4

PLATE, MAIN S (HRN)

2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 92
 DISASSEMBLY

1-3. KD-65X8005C, XBR-65X800C/805C/807C/809C/810C

1-3-26. LCD PANEL

LCD PANEL

NOTE:

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 93
 DISASSEMBLY

1-4. SMART CORE

1-4-1. BRACKET, WIFI ASSY

2 3
BRACKET, WIFI ASSY

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 94
 DISASSEMBLY

1-4. SMART CORE

1-4-2. WLAN / BT MODULE(11AC) ASSY

1 2

NOTE:
3

1
WLAN / BT MODULE(11AC) ASSY

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 95
 DISASSEMBLY

1-4. SMART CORE

1-4-3. SHEET, THERMAL (SC) AND WLAN / BT MODULE(11AC)

SHEET, THERMAL (SC) WLAN / BT MODULE(11AC)

Opposite side of WLAN / BT

MODULE (11AC) ASSY

1-4-4. HEAT SINK (SC) AND BRACKET, WIFI

HEAT SINK (SC)

1 2

BRACKET, WIFI

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 96
 DISASSEMBLY

1-4. SMART CORE

1-4-5. COVER, TOP

NOTE:

1 2

COVER, TOP

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 97
 DISASSEMBLY

1-4. SMART CORE

1-4-6. PANEL, ORNAMENT

2 3

PANEL, ORNAMENT
2

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 98
 DISASSEMBLY

1-4. SMART CORE

1-4-7. LIGHT, GUIDE

2 3
LIGHT, GUIDE

LIGHT, GUIDE

LOCK PORTION

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 99
 DISASSEMBLY

1-4. SMART CORE

1-4-8. HSC3_L MOUNT

1 2

NOTE:

HSC3_L MOUNT

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 100
 DISASSEMBLY

1-4. SMART CORE

1-4-9. CASE, BOTTOM (LL)

CASE, BOTTOM (LL)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 101
SEC 2. ADJUSTMENT
HOW TO ENTER THE SERVICE MODE
1) Turn on the main power switch to set in standby mode. 4) How to use the remote commander.
2) Press the buttons on the remote commander in the following sequence
with each interval within 1 sec, then the service mode will be set. Function The flow of control
Service mode on <Display><5><Vol Up><Power>
Service mode off <MENU>/<HOME>
Item up / down <↑>/ <↓>
Item select left/right <←>/<→>
3) Service mode display.
Execute <OK>

Service Mode
Model Information >> 5) After entering service mode, then turn off the power switch.
Self diagnosis History >>
Video / Audio >>
Panel / PQ >> Summary of key behavior
General Setting >>
Tuner >> Key Behavior
Wifi >> Menu Close service menu

Return Previous page, Change potion of focus item,

Cursor/Enter
Enter next page of focus item, etc..

[</>] Set [Home]Exit

Return Return to previous page, close service menu etc..

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 102
 ADJUSTMENT

SOFTWARE VERSION
1) In Service Mode, select “Model Information”, press “Enter” or “→ ” button to enter Status Information.

Main Micro
Service Mode Model SW Version: PKG2.011.0010NAB
NVM Version: 0001 UC2
Model Information >> Boot Version: V1.000
Self diagnosis History >> Status Information >> PQ Version: 102100006
AQ Version: AQ1.100
Video / Audio >> Model Information >> <Ext>
exFRC: 00.00.00.00
Panel / PQ >> Model Number Setting >> CameraVID: 0
General Setting >> SERIAL NUMBER EDIT CameraPIC: 0
>>
CameraFW: 0
Tuner >> 4k BE
MLFW: SF1.002
Wifi >> MAFW: SF0.360
ADSP SF0.501
NDAT SD0.370
PDAT SD0.370
BDAT SD1.011
BCM SD-------
FDAT SD0.002
UDAT SD0.000
[</>] Set [Home]Exit [</>] Set [Home]Exit BDIX SD0.370

2) Press “Enter” or “Return” button to return to Service Mode.

Service Mode
Model Information >>
Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi >>

[</>] Set [Home]Exit

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 103
 ADJUSTMENT

SERIAL NUMBER EDIT (1)

Service Mode
1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” then pressing “Enter” or Model Information >>
Self diagnosis History >>
“→” button to enter inside. Video / Audio >>
Panel / PQ >>
General Setting >>
2) Select “Serial Number Edit” by pressing “↑” or “↓” button then pressing “Enter” or “→” button Tuner >>
Wifi >>
3) Press “↑” or “↓” to input numbers.
4) After user input data , press <Enter> . [</>] Set [Home]Exit

• Pop-up dialog appear to confirm input data correct

Mode
• Serial Number can be set ONLY ONCE
Status Information >>
Model Information >>
Model Number Setting >>
5) Press “→” or “←” button to select YES or NO. Select YES if input data is correct. Select NO if Serial Number Edit _ _ _ _ _ _ _

input data is incorrect. Press <Enter> to save answer.

Service Mode

Status Information >>

Model Information >>
Model Number Setting >>
Serial Number Edit 9 9 9 9 9 9 9

Input Data correct?

Yes No

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 104
 ADJUSTMENT

SERIAL NUMBER EDIT (2)

Service Mode
If YES is selected, the input data is saved into EEPROM.
SERIAL NUMBER EDIT is greyed out and the serial number that has been input is displayed. Status Information >>

Model Information >>

User will not able to edit anymore.
Model Number Setting <[ KDL-40X500B ]>

Serial Number Edit 9999999

If NO is selected, the input data is not saved into EEPROM. Service Mode

The serial number that has been input is displayed. >>

Status Information
User can still edit the Serial Number. Model Information >>

Model Number Setting <[ KDL-40X500B ]>

Serial Number Edit 9 9 9 9 9 9 9

Input Data correct?

Yes No

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 105
 ADJUSTMENT

MODEL NUMBER SETTING

1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.
2) Select “Model Number Setting” by pressing “↑” or “↓” button then pressing “Enter” or “→” button.
3) Press “↑” or “↓” arrow key to scroll Product Name Candidate.
 (e.g. KDL-40X500B CO1,KDL-40X500C BR6)
4) Select one Product Name from the list, press <Enter> will pop dialog to inform user to confirm data. Model dependent settings will be overwritten into EEPROM.

Service Mode Service Mode [MODEL_NUMBER_SETTING]

Model Information >>
Status Information >>
Self diagnosis History >>
Model Information >>
Video / Audio >>
Model Number Setting >>
Panel / PQ >>
General Setting >> Serial Number Edit >>
____________
Tuner >>
Wifi >>

OK

[</>] Set [Home]Exit

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 106
 ADJUSTMENT

WB ADJUSTMENT
(Please apply when main board or panel is replaced.) c. To change data , press “←” or “→” on remote commander.
In “Panel/PQ” service mode.
a. Go to “WB Adjustment” category by “↑” or “↓”.
Back <<
Service Mode R WB Gain <[ 0 ]>
Model Information >> G WB Gain <[ 0 ]>
Self diagnosis History >> B WB Gain <[ 0 ]>
Video / Audio >> R WB Offset <[ 0 ]>
Panel / PQ >> G WB Offset <[ 0 ]>
General Setting >> B WB Offset <[ 0 ]>
Tuner >>
Wifi / BT >>

[</>] Set [Home]Exit

b. To select “WB Adjustment”, press “→” button.

[</>] Set [Home]Exit

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 107
 ADJUSTMENT

WB/MURA/CUC DATA TRANSFER 2. In “WB/Mura/CUC data transfer”.

(Please apply when main board or panel is replaced.) a. Select “WB/Gamma data transfer” by pressing “↑” or “↓” on remote commander.
1. In “Panel/PQ” service mode. b. To change the items, press “←” or “→” on remote commander and press “Enter”
a. Go to “WB/Mura/CUC data transfer” category by “↑” or “↓”. button.
Selectable items are:
Service Mode 0. SoC to T-con
Model Information >>
1. T-con to SoC
Self diagnosis History >>
Video / Audio >> 2. Not action
Panel / PQ >> c. Select “[start]” and press “Enter” button to start transfer.
General Setting >>
Tuner >>
Wifi / BT >> Back <<
WB/Gamma data transfer <[ 0. SoC to T-con ]>
Mura data transfer <[ 0. SoC to T-con ]>
CUC data transfer <[ 0. SoC to T-con ]>
b. To select “WB/Mura/CUC data transfer”, press “→” button.
[</>] Set [Home]Exit [Start]
c. To change data , press “←” or “→” on remote commander.

[</>] Set [Home]Exit

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 108
 ADJUSTMENT

HDD PERFORMANCE CHECK 3. A message "Please wait ..." is displayed during performance check processing.
1. In “Service Mode”, select “General Setting” by pressing “↑” or “↓” then
pressing “Enter” or “→” button to enter inside.
Service Mode

Service Mode
Model Information >> Please wait…
Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi / BT >>

2. Select “HDD Performance[</>]

checkSet”[Home]Exit
by pressing “↑” or “↓” then pressing 4. Result OK or NG will be displayed after performance of HDD is checked
“Enter” or “→” button to enter inside.

HDD Performance
HDD Performace Check
Check
General Setting

Back << Result <[ NG ]>

Aging mode <[On/Off]> Back <<
HDD Performance Check >>
AAA >>
Update CI+ Credentials >>
Boot count reset >>
ECS Enable <[On/Off]>

[</>] Set [Home]Exit

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 109
 ADJUSTMENT

HDD RE-REGISTRATION
1) In “Service Mode”, select “General Setting” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.
2) Select “AAA” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.

Service Mode General Setting

Model Information >>
Back <<
Self diagnosis History >>
Video / Audio >>
Aging mode <[On/Off]>
Panel / PQ >> HDD Performance Check >>
General Setting >> AAA >>
Tuner >> Update CI+ Credentials >>
Wifi / BT >> Boot count reset >>
ECS Enable <[On/Off]>

[</>] Set [Home]Exit [</>] Set [Home]Exit

3) Result OK or NG will be displayed after HDD re-registration is succeed/failed.

HDD Re-Register

Result <[ NG ]>

Back <<

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 110
SEC 3. TROUBLE SHOOTING
3-1. TRIAGE

Chart of triage information

1. Confirm the claimed symptom.
2. Select that symptom from the chart.
3. Bring all the boards and cables listed for that symptom.
4. Follow the troubleshooting charts in the technical guides to isolate the board.
5. Chart Color Code.

RED DOT: Most likely defective part

BLUE TRIANGLE: Secondary possible defective part
BLACK TEXT: Board that may correct the symptom

Symptoms - Shutdown. Power LED No Video Bluetooth

Remote Network Audio Skype Smart Core
blinking red diagnostics sequences Power - missing or distorted (BT)

No White
Reference Power LED Stationary
Bluetooth /
Smart Core no One Step
& does not colored No video One No video all Wireless Skype
2 3 4 5 6 7 8 9 10 No Remote No Audio LED (Set is still Remote
response to lines or of Inputs Inputs can't connect Can't Work
alive) (OSR) can't
remote dots
connect
(Dead Set)

B* Board p l p p p l l p p l l p p l p p p

G* Board l p p p l l p

H* Board p l l

K* Board p l

Speaker p l

Wifi & BT Module l l p l

LD* Board l p

V By One FFC p p p

Tcon l p p p

LCD Panel p l l p l p

Panel
(Communi Panel Soft-
Power Power LD cation) (Backlight) TEMP ware Emitter
Problem Local
Audio UART
Local
I2C

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 111
 TROUBLE SHOOTING

3-2. NO POWER
3-2-1. NO POWER-PCU

No Power

Check STBY 3.3V NG Replace NG

C9030 Between G* Board to G* Board
On B* board B* Board Harness

OK OK

Harness

B* Board

u-Com Failure

DDCON/LDO

Main Device Failure

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 112
 TROUBLE SHOOTING

3-2-2. NO POWER-U-Com Failure (1/2)

START

Check MAIN_VCC
No
Check C9117 Voltage. No Check +3.3V_STBY R9175 Voltage. G-Board
Is the voltage >3.0V? R9144, CN9000 #26pin Is the voltage >1.6V?

Yes
Yes

No Check P_ON_VBUS No
Check R9186 Voltage. Check DC_OFF_DET P-on ucom #pin11 Change IC9017
Is the voltage >3.0V? IC9018 is >3.0V?

Yes
Yes

Check STBY_MHL No SOC

Check OPWRSB No R9176 Voltage. Muffin Check P_ON_#1 No
R9179 Voltage. Is the voltage >3.0V? problem P-on ucom #pin13 Change IC9017
Is the voltage 0V? is >3.0V?

Yes
Yes Yes
No problem
TV set stays in Check PGOOD_1 No No POWER - DDCON/LDO
STBY MHL charge mode. R9173 Voltage.
Check 1.0V DDCON (IC9008)
Is the voltage >3.0V?

Try AC Off and On after few minutes.

Check POWER_ON No If #pin19 keep Low, change IC9017.
P-on ucom #pin19
If #pin19 goes High few seconds and downs to Low,
Is the voltage >3.0V?
Check G board and harness.
yes
A

Check P_ON_LNB No To the next page

P-on ucom #pin15 Change IC9017
Is the voltage >3.0V?

Yes

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 113
 TROUBLE SHOOTING

3-2-2. NO POWER-U-Com Failure (2/2)

From previous page

Yes

Check P_ON_#2 No
P-on ucom #pin14 Change IC9017
Is the voltage >3.0V?

Yes

Check ORESETB No
P-on ucom #pin12 Change IC9017
Is the voltage >3.0V?

Yes

Check X_SYSTEM_RST
No
P-on ucom #pin16 Change IC9017
Is the voltage >3.0V?

Yes

If PANEL_PWER_ON (R9172) is 0V
Check XRST No
Change IC9017
P-on ucom #pin17
Is the voltage >3.0V?

Yes

If BL_MUTE (R9174) is 0V
Check BL_ON No
Change IC9017
P-on ucom #pin18
Is the voltage >3.0V?
Yes

END
Ucom IC9017 is working OK

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 114
 TROUBLE SHOOTING

3-2-3. NO POWER: DC_OFF_DET check 3-2-4. NO POWER: DDCONs check

START
START

Check fuse No
F9xxx Change Fuse
Check Vdd No Is fuse OK?
C9118 Change IC9018
Is voltage >5V?
Yes
Yes Check Vcc voltage No Check POWER_ON P-on ucom #pin19
C9xxx
END Is voltage >12.0V? (Refer to No Power U-Com Failure)

Yes

Check Enable pin No

voltage No Power U-Com Failure
Is voltage >2.5V?

Yes

Change DDCON IC

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 115
 TROUBLE SHOOTING

3-2-5. NO POWER: DDCON check

START

Check IC9403 Vcc voltage Check Vcc voltage No Check No

No
C9428 C9061 D9000 Change D9000
Is voltage >12V? Is voltage >3V? Is diode ?

Yes Yes Yes

Check G board and harness

Check Vcc voltage No Check No

C9061 D9001 Change D9001
Is voltage >4V? Is diode ?

Yes Yes
Check +5V_MAIN DDCON (IC9001)

Check Enable No
IC9010 #pin1 Change IC9010
Is voltage >2.5V?

Yes

Change DDCON
IC9009

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 116
 TROUBLE SHOOTING

3-2-6. NO POWER: LDOs check check

START

Yes

Check Vcc voltage No

C9xxx Check +3.3V_MAIN DDCON (IC9003)
Is voltage >3V?

Yes

Check Enable pin No

voltage 1.2 No Power U-Com Failure
Is voltage >3V?

Yes

Change LDO IC

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 117
 TROUBLE SHOOTING

3-3. STANDBY LED BLINKING

3-3-1. 2 Times Blinking (Main power Error) 3-3-2. 3 Times Blinking (DC Alert)

BMFL/BMFW board
2-time blinking

3-time blinking

Check +12V_REG DC_ALERT

at pin 13/15/17 of CN9000 Yes
G* Board
on B* Board, Check +5.0V_MAIN NG
IC9014,etc
Voltage > 13.2V ? at pin1 in IC8001, 4.959V
(B* Board)
<Voltage<5.285V?
No
OK

B* Board

AUDIO

Go to Audio check point

HDMI

Go to HDMI check point

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 118
 TROUBLE SHOOTING

3-3-3. 3 Times Blinking (Audio Error)

LED 3x blinking Yes

Segment “XS”?

No No
Audio Error ? See other flow
Replace B-K Harness Yes
B-K harness NG
OK ?
Yes

No

Go to page
Replace K-PWB Yes
Power Off Checking*1 K-PWB NG
OK ?

Go to page No
Power off Checking*2

Replace B-PWB Yes

B-PWB NG
OK ?

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 119
 TROUBLE SHOOTING

Note 1: Note 2:
(1) PVDD-GND short check (1) PVDD-GND short check
1) Power Off Checking*1 Measure impedance between PVDD and GND at C7706, Measure impedance between PVDD and GND at C7722, C7762, C7782,
C7707. C7834.
If impedance is <100Ω → NG
If impedance is <100Ω → NG
(2) LDO out short check
(2) LDO out short check
Measure impedance between +3.3V and GND at C9130.
If impedance is <100Ω → NG
Measure impedance between +3.3V and GND at
C7909.
Power Off Check*1 (3) Fuse open check If impedance is <100Ω → NG
Measure impedance of fuse F7700, F7702 5A (12.5V)
If fuse open → NG (3) Fuse open check
Measure impedance of fuse
F7702, F7704, F7705, F7701 5A (12.5V)
Segment “XS”? F7700 3.15A (DDC5V)
Yes If fuse open → NG

No
Power Off Check*3
(1) B-PWB (1) K-PWB
PVDD-GND short ? PVDD-GND short ?
(See Note 1) Yes (See Note 2) Yes

No No Measure the Speaker

impedance by multi-meter Replace Speaker
(2) B-PWB (2) K-PWB Less than 3Ω ? Yes
LDO out short ? LDO out short ?
(See Note 1) Yes (See Note 2) Yes No
Confirm the speaker
No No harness
Replace Speaker Harness
Cut or shorted Yes
(3) B-PWB (3) K-PWB
to the chassis ?
Fuse broken ? Fuse broken ?
(See Note 1) Yes (See Note 2) Yes No

No Replace B-PWB No Replace K-PWB Return to LED 3x blinking

or Power Off Checking*3

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 120
 TROUBLE SHOOTING

2) Power Off Checking*2

(4) 12.5V check BMFL / BMFW

Measure voltage between PVDD and GND at
capacitor C7706 or C7707.(See 3.3)
Power Off Check*2 Voltage rise more than 0V for a moment at
power on
→ Yes
Yes
Segment “XS”? (5) 12.5V check KS-PWB (XS)
Measure voltage between PVDD and GND at
capacitor C7722, C7762, C7782 or C7834. (See
No
3.3)
(5) 12.5V check
(4) 12.5V check Yes Voltage rise more than 0V for a moment at
12.5V is supplied to
12.5V is supplied to Yes power on
K-PWB for a moment
B-PWB for a moment → Yes
before LED 3x blinking ?
before LED 3x blinking ?
No
No

Yes Replace G-K Harness Yes

Replace B-K Harness
OK ?
OK ?

No No

Replace G-PWB Yes Replace G-PWB Yes

OK ? OK ?

No No
Return to Return to
LED 3x blinking LED 3x blinking
Finish Finish

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 121
 TROUBLE SHOOTING

3) Power Off Checking*3

No Sound
Without LED 3x
No sound only Yes Go to
Analog RF and Digital RF ? No Sound Tuner
Select [External Inputs]→
AV receiver is connected Yes
[BRAVIA Sync Settings]→
to HDMI in ?
[BRAVIA Sync Control]→[off] No
No
Yes Go to
No sound only HDMI ?
No Sound HDMI
[Speakers] setting is Yes Change the setting to
[Audio System] ? [TV Speakers] No

No Go to
No Sound Audio
Headphone is connected to Yes
Disconnect the Headphone
HP/Audio Out terminal ?

No
[Sound]→ Change [Sound]→
Yes
[Headphone Speaker Link] [Headphone Speaker Link]
setting is [On] ? Yes to [Off], OK ?
No No

Replace B-PWB
Go to
Power Off Checking*1 HP/Audio out terminal or Headphone detect
GPIO may be broken

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 122
 TROUBLE SHOOTING

3-3-4. 3 Times Blinking (HDMI EQ Error)

This 3 times blinking function for HDMI EQ

BMFL/BMFW board error has been disabled for the SW later
than PKG2173.
So, for the above applicable models, you
3-time blinking Check can Ignore this flow.
I2C_C bus signal. NG IC5212
at CL5259 and Or IC1000 For those models with the SW before
CL5261. PKG2073.
Check
This 3 times blinking function for HDMI
VS GND impedance NG
EQ error has been enabled except for the
of +1.0V_HDMI IC5212 OK
sets with the SW updated by OTA.
at HDMI EQ side
(ex.C5335) Check
OK Voltage
of +1.0V_HDMI,
EQ_+3.3V_MAIN, NG Power,
Check +5V_BOSTON DDCON
VS GND impedance NG at HDMI EQ side
of EQ_+3.3V_MAIN IC5212 (ex.C5335, C5317,
at HDMI EQ side and C5351, )
(ex.C5317)
OK
OK
X’tal or
around parts.
Check
NG X5202,
Check Frequency of X’tal
R5478(100ohm),
VS GND impedance NG (X5202)
R5368(1Mohm)
of +5V_BOSTON IC5212 27MHz?
C5298(10pF)
at HDMI EQ side OK C5297(12pF)
(ex.C5351)

OK
IC1000

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 123
 TROUBLE SHOOTING

3-3-5. 4 Times Blinking (LED Voltage Error)

4-time blinking

Between 0.898V to 2.997V

Check LED driver or G* board

R9027
on the B* Board  Change LD board or G* board.

0.897V or less

B* Board

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 124
 TROUBLE SHOOTING

3-3-6. 5 Times Blinking (Panel Communication Error)

5-times blinking

NG
Change Change
B-Board Panel (T-con)
Check NG OK
“+12.5V_TCON” at G-Board is
Replace G-Board
CN9000 suspicious
Symptom Symptom
on the B-Board
improvement improvement
NG
OK B-Board is Panel (T-Con) is
suspicious suspicious
Symptom
Replace the Harness improve Harness is
Between G-Board
suspicious
and B-Board

NG

Symptom
improve
Replace V-By-One FFC
the V-By-One FFC is suspicious

NG

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 125
 TROUBLE SHOOTING

3-3-7. 6 Times Blinking (Backlight Error)

6-times blinking

Check a voltage of
Harness /
BL_ERR_DET. Check
Connection
Check point is Voltage ≥ 1.9 V harness/connection
Change Symptom
broken
JL9007 G*board to B*Board Harness
harness Improvement
or or
23pin of CN9000 LD board to B*Board
No improvement
on B*Board

Voltage < 1.8 V Harness /

Connection OK LED driver or G* board Symptom
LD board/G board
 Change LD board or G* board. Improvement

No improvement
Change Symptom
Panel
Panel Improvement

No Improvement
Change Symptom
B* Board
B* board Improvement

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 126
 TROUBLE SHOOTING

3-3-8. 7 Times Blinking (Temperature Error)

7-time blinking

Setting
circumstance is OK? No Set to another
Temperature, location, etc.
Ventilation, etc.

Yes
Change B* Board, NG
and Aging a few Panel
hours

Symptom
improvement
Check I2C_C bus Yes Temp sensor
B* Board NG communication OK?
IC1400
(check the next page)
No

I2C_C bus dumping or

Muffin check

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 127
 TROUBLE SHOOTING

3-4. NO SOUND
3-4-1. No Sound Audio 3-4-2. No Sound : TUNER

No Sound No Sound with normal picture

Audio

Yes NO
Segment “XS”? Only RF tuner input?

YES
No

Replace B-K Harness Yes

Please refer Audio
OK ? Check IC1000 (SOC)
troubleshooting

No

Replace K-PWB Yes

OK ?

No

Replace B-PWB Yes

OK ?

Finish

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 128
 TROUBLE SHOOTING

3-4-3. No Sound : MHL

No Sound

NG
Check the picture Refer to MHL NO PICTURE

OK

OK
Check Sound by other TV set
Refer to No Sound Audio
which is same model

NG

Check Source equipment

OK
by Reference TV set
Change B-Board.
(For example, Samsung TV(UN46ES7000),
Toshiba TV(42WL863), RB1 or RB2)

NG

Check the settings of

Source equipment

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 129
 TROUBLE SHOOTING

3-4-4. No Sound : HDMI1/2/3/4

No Sound

NG
Check the picture Refer to HDMI (1/2/3/4) NO PICTURE

OK
Does this model have YES
Check the mode DVI Connect Stereo minijack cable between Source and the TV, and
Analog Audio In
of Source equipment Change “HDMI/DVI Audio Source” to Auto or Analog Audio In.
(Stereo minijack)?
No
HDMI Change the mode of Source equipment to HDMI

Analog Audio In
Does this model have YES “HDMI/DVI Audio Source”
Analog Audio In Change “HDMI/DVI Audio Source” to Auto or HDMI Audio In
setting is?
(Stereo minijack)?
Auto or HDMI Audio
NO

Check Sound by other TV set OK

Refer to No Sound Audio
which is same model

NG

Check Source equipment OK

NO
Is Distributor used ? by Reference TV set Change B-Board.
(For example, RB2, RB1)
YES
NG

Connect Source Check the settings of

equipment directly Source equipment

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 130
 TROUBLE SHOOTING

3-5. NO PICUTURE

No Picture BL_ON (L or H): IC9017 #18pin (for 4K BMFW/BMFL board)

BL_ON：H
No Check Smart Core No Check Replace NG NG
Got Any Normal Replace LCD Panel
Behavior BL_ON the V by One FFC
Display? the main Board (T-CON)
(5x Blinking) on the main board Harness

Yes Symptom Symptom

Yes BL_ON：L
improvement improvement

Check Other 5x Blinking Backlight V by One FFC

Main board NG
Portion: Harness

Ext. Video Input -

No Picture

HDMI - No Picture

Tuner - No Picture

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 131
 TROUBLE SHOOTING

3-5-1. No Picture AEP Destination (BMFL/BMFW) SCART

No Picture AEP

SCART RGB SCART CVBS

No Picture No Picture
NG
NG
[LOW: 0V]
[LOW: 0V]
OK NG NG
Check SCART_FB ** Detailed check all parts Check SCART_FB
* Check CN7501 * Check CN7501
IC1000 L37 at SCART_FB signal IC1000 L37
Connection Connection
[SOY0] at R7514 Path [VD7504/R7513] [SOY0] at R7514
OK
OK [HIGH: 0.4V  Composite] NG OK [HIGH: 0.4V  Composite]
OK
OK [HIGH: 3V  RGB] OK [HIGH: 3V  RGB]

NG
** Detailed check all parts
at SCART_FB signal
** Detailed check all parts at Path [VD7504/R7513]
CN7501 along signal path
at Pin No: OK
Check wave between NG (Vpp: 0 V)
7 : [VD7503/R7503/C7501/ Detailed check all parts at
C7502/C7505/C7507 R7504] NG (Vpp: 0 V) CN7501 along signal path NG
and IC1000 11 : [VD7502/R7506/C7503/ NG Check wave between
at Pin No:
R7507] C7511 and IC1000
20 : [D7505/R7518/C7510/
15 : [VD7501/R7510/C7506/ R7599/R7519]
OK (Vpp: 1 V) R7511]
OK (Vpp: 1 V)

OK OK

Muffin [IC1000] CN7501 Connectivity CN7501 Connector Muffin [IC1000] CN7501 Connector CN7501 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 132
 TROUBLE SHOOTING

3-5-2. No Picture AEP Destination (BMFL/BMFW) VIDEO

No Picture AEP

Video 2 Component
No Picture No Picture

NG NG * Check J7504 Con

Check if input OSD
* Check J7504 NG (Vpp: 0 V) Check if input OSD
VIDEO_DET at NG (Vpp: 0 V)
Connection, is GREY OUT
is GREY OUT
VIDEO_DET R7539,
OK if it is highlighted OK if it is highlighted
At R7539 CR_DET at R7538

OK OK (Vpp: 3.3 V) OK OK (Vpp: 3.3 V)

** Detailed check all NG (Vpp: 0 V) ** Detailed check all parts

parts at VIDEO_DET at VIDEO_DET signal NG (Vpp: 0 V)
signal Path [R7535] Path [R7535] and CR_DET
signal path [R7534]
OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)

** Detailed check all parts

at signal path of:
NG (Vpp: 0 V) ** Detailed check all parts NG Check wave Y1P : [D7530/R7524/C7514/
NG
Check wave between NG (Vpp: 0 V)
at CVBS3P signal path Between R7527]
C7512 and IC1000
[D7530/R7524/R7525] C7515/C7518/C7520 PB1P : [VD7508/R7529/C7517/
and IC1000 R7530]
PR1P : [VD7509/R7532/C7519/
OK (Vpp: 1 V) OK
OK (Vpp: 1 V) R7553]

OK

Muffin [IC1000] J7504 Connector J7504 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 133
 TROUBLE SHOOTING

3-5-3. No Picture CH/MX/PA/COL/LA (BMFL/BMFW)

No Picture Video

Video 1 Video 2
No Picture No Picture

NG
NG * Check J7505 * Check J7504
Check if input OSD NG (Vpp: 0 V) Check if input OSD NG (Vpp: 0 V)
Connection, Connection,
is GREY OUT is GREY OUT
VIDEO2_DET VIDEO_DET
OK if it is highlighted OK if it is highlighted
At R7562 At R7539

OK OK (Vpp: 3.3 V) OK OK (Vpp: 3.3 V)

** Detailed check all NG (Vpp: 0 V)

parts at VIDEO2_DET ** Detailed check all NG (Vpp: 0 V)
Signal Path [R7561] parts at VIDEO_DET
Signal Path [R7535]

OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)

NG (Vpp: 0 V) ** Detailed check all parts NG NG (Vpp: 0 V)

Check wave between at CVBS2P signal path
Check wave between ** Detailed check all parts NG
C7511 and IC1000 [D7514/R721/C7521/ at CVBS3P signal path
C7512 and IC1000
R7519/C7534] [D7530/R7524/R7525]

OK (Vpp: 1 V) OK
OK (Vpp: 1 V) OK

Muffin [IC1000] J7505 Connector J7505 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 134
 TROUBLE SHOOTING

3-5-4. No Picture CH/MX/PA2/NZ/AUS/BR/COL/BR/UC/HK/TW (BMX)

No Picture Video

Component
No Picture

NG
Check if input OSD * Check J7504 Con NG (Vpp: 0 V)
is GREY OUT VIDEO_DET at R7539,
OK if it is highlighted CR_DET at R7538

OK
OK (Vpp: 3.3 V)

** Detailed check all parts

NG (Vpp: 0 V)
at VIDEO_DET signal
Path [R7535] and CR_DET
signal path [R7534]

OK (Vpp: 3.3 V)

** Detailed check all parts

at signal path of:
Check wave Y1P : [D7530/R7524/C7514/ NG
NG (Vpp: 0 V)
Between R7527]
C7515/C7518/C7520 PB1P : [VD7508/R7529/C7517/
and IC1000 R7530]
PR1P : [VD7509/R7532/C7519/
OK (Vpp: 1 V) R7553]

OK

Muffin [IC1000] J7504 Connector J7504 Connectivity

Problem Parts Broken
Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 135
 TROUBLE SHOOTING

3-5-5. No Picture J/UC/HK/TW Destination (BMFL/BMFW)

No Picture

Video1 Video2
No Picture No Picture

NG * Check J7501 NG * Check J7504

Check if input OSD NG (Vpp: 0 V) Check if input OSD NG (Vpp: 0 V)
Connection, Connection,
is GREY OUT is GREY OUT
VIDEO2_DET VIDEO_DET
OK if it is highlighted OK if it is highlighted
At R7537 At R7539

OK OK (Vpp: 3.3 V) OK OK (Vpp: 3.3 V)

** Detailed check all NG (Vpp: 0 V)

parts at VIDEO2_DET ** Detailed check all NG (Vpp: 0 V)
Signal Path [R7556] parts at VIDEO_DET
Signal Path [R7535]
OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)

** Detailed check all parts NG NG (Vpp: 0 V)

NG (Vpp: 0 V)
Check wave between at CVBS2P signal path
Check wave between
** Detailed check all parts NG
C7511 and IC1000 [D7505/R7559/ at CVBS3P signal path
C7512 and IC1000
C7511etc] [D7530/R7524/R7525]

OK (Vpp: 1 V) OK
OK (Vpp: 1 V) OK

Muffin [IC1000] J7501 Connector J7501 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 136
 TROUBLE SHOOTING

3-5-6. No Picture J/UC/HK/TW Destination (BMFL/BMFW)

No Picture

Component
No Picture

Check if input OSD NG * Check J7504 Con NG (Vpp: 0 V)

is GREY OUT VIDEO_DET at R7539,
OK if it is highlighted CR_DET at R7538

OK
OK (Vpp: 3.3 V)

** Detailed check all parts NG (Vpp: 0 V)

at VIDEO_DET signal
Path [R7535] and CR_DET
signal path [R7534]

OK (Vpp: 3.3 V)

** Detailed check all parts

at signal path of:
Check wave NG (Vpp: 0 V) Y1P : [D7530/R7524/C7514/ NG
Between R7527]
C7515/C7518/C7520 PB1P : [VD7508/R7529/C7517/
and IC1000 R7530]
PR1P : [VD7509/R7532/C7519/
R7553]
OK (Vpp: 1 V)

OK

Muffin [IC1000] J7504 Connector J7504 Connectivity

Problem Parts Broken
Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 137
 TROUBLE SHOOTING

3-5-7. No Picture : @ Tuner

Notes:
I2C line for all tuners except Japan_SKP
- Parts for I2C_A_SDA line: R6001, C6004.
RF input no picture / noisy picture - Parts for I2C_A_SCL line: R6002, C6005.

I2C line for Japan_SKP

Check RF source cable NG - Parts for I2C_D_SDA line: R6003,C6006
Change RF cable and antenna - Parts for I2C_D_SCL line: R6004,C6007
and antenna, OK?
OK TU_1.1V line only in Japan_SKP Tuner
- Parts for TU_1.1V: FB6800
Check Tuner power line:
3.3V at JL6005 = 3.3V?
1.8V at JL6006 = 1.8V? NG Please refer DDCON
DEM_3.3V at JL6019 = 3.3V? troubleshooting
A_RESET value at JL6012 = 3.3V?
For JP_SK only – TU1.1 V (Refer notes)
OK
Check part mounting condition
YES for “I2C_A_SDA, I2C_A_SCL NG
All broadcasting channel Change NG parts
or
cannot be received? connected to I2C bus
I2C_D_SDA, I2C_D_SCL”
Refer Note I2C
NO
OK

Digital

Satellite

Check Tuner power line NG 12V LNB Voltage

Terrestrial/Cable
Analog 12V at JL6027 = 12V? Checking
OK

For TW & NA-ATSC All tuners except

(MX/UC) only TW & NA-ATSC(MX/UC)

Refer Analog Tuning Refer Digital Tuning 1 Refer Digital Tuning 2

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 138
 TROUBLE SHOOTING

3-5-8. FOR 12V LNB Voltage Checking: @ AEP_W and JP_SKP

12V LNB Voltage Checking

OK OK OK
Check Tuner power line Check P_ON_LNB signal line MOSFET Q9019
Check fuse F6000
12V at JL9012 = 12V? at R9167 = 3.3V? broken

NG NG NG

Please refer DDCON

Change the fuse troubleshooting

NG
Check harness between
Harness broken
B-Board and G-board

OK

Please refer G-board

troubleshooting

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 139
 TROUBLE SHOOTING

3-5-9. FOR ANALOG TUNING: @ All destination except JP

Notes:
- Parts for IFOUT_N line: R6007, FB6002, C6008, R6327,
C6301, R6301.
- Parts for IFOUT_P line: R6008, FB6003, C6009, R6326,
C6300, R6300.
For LA-ISDB(BR/AR), LA-T2(COL) and TW only - Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302,
Analog Tuning
R6303.
For Other destination
NG A : Insert correct signal in correct terminal.
Confirm ANT or Cable connection A

OK

Check part mounting condition for NG

analog control line Change NG parts
“IFOUT_N, IFOUT_P, IFAGC”

OK

Check IC1000(SOC)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 140
 TROUBLE SHOOTING

3-5-10. FOR DIGITAL TUNING 1: @ TW, NA-ATSC(MX/UC), JP_SKP and LA-T2(COL)

Notes:
- Parts for IFOUT_N line: R6007, FB6002, C6008, R6327, C6301,
R6301.
- Parts for IFOUT_P line: R6008, FB6003, C6009, R6326, C6300,
Digital Tuning 1 R6300.
- Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302,
For TW only R6303.
For all
tuners A : Insert correct signal in correct terminal.
NG
except TW
Confirm ANT or Cable connection A

OK
Sound is normal?

Check IC1000 (SoC)

No sound

OK
Check part mounting condition for digital data line
“IFOUT_N, IFOUT_P, IFAGC”

NG

Change NG parts Check SOC(IC1000) and Tuner

module

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 141
 TROUBLE SHOOTING

3-5-11. FOR DIGITAL TUNING 2: @ AEP_W, JP_SKP, PA_T2, CH/HK, LA-ISDB(BR/AR) and LA-T2(COL)

For LA-ISDB(BR) and Digital Tuning 2

LA-T2(COL) only

For AEP-W For JP_SKP

NG For PA_T2 and NG
CH/HK only NG
Confirm ANT or Cable connection A Confirm ANT or Satellite connection A Confirm ANT or Satellite connection A

OK OK OK
Terrestrial All except SKP_Opticast BS/CS or SKP_Opticast/
Digital cable/ Terrestrial
SKP_Premium or terrestrial

Cable OK SKP_Opticast
Sound is normal?

Refer to Digital Tuning 1 No sound Refer to Digital Tuning 1

Check IC1000 (SoC)

On Service Notes:
mode display CASE B - Parts for TU1_TS_DATA0 line: R6015,
TS_LOCK ? R6321.
UEC ? - Parts for TU1_TS_CLK line: R6016, R6322.
- Parts for TU1_TS_VALID line: R6017, R6323.
CASE A - Parts for TU1_TS_SYNC line: R6018, R6324.
Change Tuner module
(Refer to Note tuner ) - CASE A : TS _LOCK = LOCK and UEC
constant
- CASE B : TS _LOCK = UNLOCK or UEC is
OK increasing
Check part mounting condition for digital data line
“TU1_TS_DATA0, TU1_TS_CLK, TU1_TS_VALID, TU1_TS_SYNC”
Note Tuner –
(IC reference -- destination)
TU6001 - PA-T2
NG TU6001 - LA-T2/LA-ISDB
TU6001 - CH, HK
Check IC1000 (SoC)
TU6003 - AEP_W
TU6802 - JP_SKP
Change NG parts
A : Insert correct signal in correct terminal.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 142
 TROUBLE SHOOTING

3-5-12. NO PICTURE: HDMI1

No Picture

If you can do Check the below point at

component repair Connector side All lines
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5202
・Check DDC lines NG
All Inputs are NG ・Check TMDS lines

+5V line is OK Only TMDS

Only +5V line
and HPD line lines
is NG
Check Picture by other TV set is NG are NG
Change B-Board. Spec:4.7~5.3V
which is same model Spec:2.4~5.3
Other TV set V
OK Replace
Target board & other TV set If you can do JC5216, JC5217
both NG component repair Replace RB5209, RB5210
R5515 Only DDC
lines NG
are NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
(HDMI EQ).
No

Check Source equipment Replace IC5212

by Reference TV set Change B-Board. (HDMI EQ).
(For example, RB1) Reference TV Set OK

Reference TV set
NG
Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 143
 TROUBLE SHOOTING

3-5-13. NO PICTURE: HDMI2

No Picture

If you can do Check the below point at

component repair Connector side All lines
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5202
NG
・Check DDC lines
All Inputs are ・Check TMDS lines
NG
Only +5V line +5V line is OK
Only TMDS lines
is NG and HPD line
are NG
Check Picture by other TV set Spec:4.7~5.3V is NG
Change B-Board.
which is same model Spec:2.4~5.3
Other TV set
V Replace
OK If you can do
Target board & other TV set component repair JC5208, JC5209
both NG Replace Only DDC RB5211, RB5212
R5517, R5518 lines
are NG NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
(HDMI EQ).
No

Check Source equipment

by Reference TV set Change B-Board. Replace IC5212
(For example, RB1) Reference TV Set OK (HDMI EQ).

Reference TV set
NG
Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 144
 TROUBLE SHOOTING

3-5-14. NO PICTURE: HDMI3

No Picture

Check the below point at

If you can do Connector side All lines
Check other Other Input is OK component repair ・Check +5V line are NG Replace
Change B-Board.
HDMI input ・Check HPD line CN5203 NG
・Check DDC lines
All Inputs are ・Check TMDS lines
NG
Only +5V line +5V line is OK Only TMDS lines
is NG and HPD line are NG
Check Picture by other TV set
Change B-Board. Spec:4.7~5.3V is NG
which is same model Other TV Spec:2.4~5.3
set OK V Replace
If you can do JC5237, JC5238
Target board & other TV set component repair
both NG RB5213, RB5214
Replace Only DDC lines NG
R5428 are NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
No (HDMI EQ).

Check Source equipment

by Reference TV set Change B-Board. Replace IC5212
(For example, RB1) Reference TV Set OK (HDMI EQ).

Reference TV
set
NG Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 145
 TROUBLE SHOOTING

3-5-15. NO PICTURE: HDMI4

No Picture

If you can do
Check the below point at
component repair All lines
Connector side
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5208 NG
・Check DDC lines
All Inputs are NG ・Check TMDS lines

Only +5V line +5V line is OK

is NG and HPD line Only TMDS lines
Check Picture by other TV set Spec:4.7~5.3V is NG are NG
Change B-Board.
which is same model Other TV Spec:2.4~5.3
set OK V
If you can do Replace
Target board & other TV set Replace JC5239, JC5240
component repair
both NG R5467 RB5215, RB5216
Only DDC lines
are NG NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
No (HDMI EQ).

Check Source equipment

by Reference TV set Change B-Board.
(For example, RB1) Reference TV Set OK Replace IC5212
(HDMI EQ).
Reference TV
set
NG Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 146
 TROUBLE SHOOTING

3-5-16. NO PICTURE: MHL (BMX)

No Picture

Check voltage at
CD_SENSE_0,
High NG (No communications)
R5509 Check HDMI_0_HPD_CBUS
Replace IC5212(HDMI EQ).
Spec:High:2.0~5.3V at connector side
Low:0.8~2.0V
OK
Low NG (No communications)
Check TMDS(D0+/D0-) lines
at connector side
Replace
RB5211
OK
Low (< 2V)

Check DDCCLK,
Check RB5219 (47k ) Check Source equipment
at CL5256
NG (Open) by Reference TV set
High OK (For example, Samsung TV(UN46ES7000),
Replace Toshiba TV(42WL863), RB1, RB2) OK
RB5219

NG

Check HDMI picture

Check D5205, D5206
in this input
Change NG (Open)
MHL cable
OK Replace NG
D5205, D5206

Check the settings of Check “NO PICTURE

Replace IC1000 (SoC).
Source equipment – HDMI” flow

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 147
 TROUBLE SHOOTING

3-5-17. NO CHARGE: MHL (BMX)

No Charge

STBY “MHL Charge During STBY” Off

The TV Power Status? Change “MHL Charge During STBY” (UI) to “On”
(UI) Status?

TV On

5V
CN5202 #18 pin Change MHL Cable

0V
High 0V
Check voltage at 0V
Check IC5208 #6 Check IC5208 #3
CD_SENSE_0, Replace IC1000 (SoC).
(VBUS IC, Out) (VBUS IC, EN)
R5509
Low (< 2V) 5V

Low (< 2V) Replace IC5208 (VBUS IC)

Check DDCCLK, NG (Open)
Check RB5219 (47k )
at CL5256

High Replace
OK
RB5219

Change
MHL cable Check D5205, D5206 NG (Open)

Replace
OK
D5205, D5206

Replace IC1000 (SoC).

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 148
 TROUBLE SHOOTING

3-6. SIDE BUTTONS MALFUNCTION

Side Key button OK

Change Switch Unit Switch unit issue
malfunction

NG

Harness on Switch Unit OK Harness

and B* Board properly connected connection
issue
NG

Change OK
Switch unit-B* board Harness Harness issue

NG
NG
Power Key (B*Board) NG Key AD(B*Board)
NG Check parts value :
Check parts value : Parts Broken issue
0 ohm < R1089 < 2 ohm 0 ohm < R1091 < 2 ohm
4.4k ohm < R1432 < 5k ohm 0 ohm < R1042 < 2 ohm
OK OK

Power Key Muffin Pin (B*Board) OK OK Key AD muffin pin (B*Board)

Muffin IC1000 Check voltage (Power ON condition):
Check voltage(Power ON condition) :
3.13V < Voltage < 3.47V problem 1.62V < voltage < 1.84V

NG NG

Change B*Board

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 149
 TROUBLE SHOOTING

3-7. IR REMOTE COMMANDER MALFUNCTION

Check whether center Remote control battery

Center white LED OK OK
IR do not response to white LED blink ,when using
lit up when remote could be weak.
Remote Commander commander near the sensor
control is pressed windows Change battery.

NG
Harness on H-board OK Harness
and B* Board connection
properly connected issue
NG

Change OK H-B* board harness

H-B* board Harness issue

NG

OK
Change Smart Core Smart core issue

NG
B*Board
NG
Check parts value : Parts Broken issue
R1080 = zero ohm
OK

SIRCS (IC1000 Pin Y35 , B*Board) OK Muffin IC1000

Check voltage (Power ON condition):
3.287V < Voltage < 3.55V? problem

NG

Change B*Board

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 150
 TROUBLE SHOOTING

3-8. LIGHT SENSOR ERROR

Backlight doesn’t change Check UI setting for light OK

Change the UI setting User did not activate light
when ambient lighting Sensor. Make sure it is “on” to “ON” sensor function
level changed
NG

Harness on H-board and OK Harness connection

B* Board properly connected issue

NG
OK H-B* board harness
Change
H-B* board Harness issue

NG
OK
Change Smart Core Smart Core issue

NG
B*Board NG
Check LIGTH_SENSOR signal path : Part broken issue
R1079 = zero ohm
OK
LIGTH_SENSOR (Muffin Pin L35) OK
Check voltage variation from Muffin IC1000 problem
room light to dark condition
NG

Change B*Board

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 151
 TROUBLE SHOOTING

3-9. NETWORK MALFUNCTION

1) Ethernet (Wired)

[Network Set-up]
>[Wired Set-up]
on the TV

OK OK OK
Connection Results Connection Results Connection Results
Cable Connection Local Access Internet Access
B board

Failed Failed Failed

OK Auto
Check Proxy setting
Check cable B board Wired Set-up
Local router
IP address setting
DHCP server

NG Manual

Ethernet Cable Check IP address

&
Local router setting

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 152
 TROUBLE SHOOTING

2) Internal Wireless Network malfunction

Wireless Network
on the TV

Error Message appear No Is the radio field No

when the Wireless Strength too weak Bxx Board
Network is selected? or even No signal?

Yes Yes
NG
Change WiFi module Access Point
From previous page
OK

WiFi module

Check harness
NG OK
connection is OK Connect properly Loose harness
between WiFi and Bxx

OK NG
Change harness
Change NG NG
between Bxx board Change Bxx board
Wi-Fi module
and WiFi
OK If Wi-Fi malfunction happens,
OK
• Wi-Fi module
• Harness between WiFi
Wi-Fi module Main Harness and Bxx
• Bxx board
are suspected.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 153
 TROUBLE SHOOTING

3) Bluetooth malfunction

Touch pad Remote doesn’t work

Or
3D-glasses (Active) doesn’t work
Or
Bluetooth Speaker/Headphone/Headset doesn’t work

Please refer
OK Touch pad Remote manual
Home > Settings > Check BT antenna OK 3D-glasses (Active) manual
Bluetooth Settings Can read Connection is OK
Or
Near discoverable
Bluetooth Device Bluetooth Speaker/Headphone/Headset operation manual
NG NG
else

OK Loose BT antenna
Connect properly connection
NG

Check harness NG OK
connection is OK Connect properly Loose harness
between BT and Bxx

OK
NG

NG Change harness NG
Change BT module Between Bxx board Change Bxx board
and BT
OK OK

BT module Main Harness

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 154
SEC 4. DIAGRAMS
4-1. BLOCK DIAGRAM
4-1-1. UC2

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 155
 DIAGRAMS

4-1-2. LA8/AR4/ECU/BR6

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 156
 DIAGRAMS

4-1-3. CO1

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 157
 DIAGRAMS

4-1-4. LA1

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 158
 KD-49X8005C

(Only Interface between board and board）

SM (FY14) BAX_F Board

BMFW Board CN3601 To BMFW T-con Board
CN203 GND 1 51 GND
1-798-511-11(ALPS)/ HUS_GND 1 19 VBTX7P 2 50 RxP7 (LGD)
1-798-510-12(NOBLE) HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 PANEL FFC
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
5 5 WIFI_GND VBTX2P 17 35 RxP2
6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
9 9 WIFI_GND VBTX1N 21 31 RxN1
10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
11 12 BT_3D_LR VBTX0N 24 28 RxN0
13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
USB 15 16 WIFI_USB_P GND 28 24 GND
NC 17 NC GND 29 23 AGP/NSB (High/Open:AGP, Low: NSB)
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 NC
1 19 CAM_GND BITSEL 31 21 NC(BITSEL(High/Open:10Bit; L:8Bit))
CN001 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 nWP(High:Write; L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L
4-2. CONNECTOR DIAGRAM

5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA

GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 PCID_EN (High: Enable, Low/Open: Disable)
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 NC
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 NC
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 12V

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 12V
JAM SYT10-12WS SYT10-12HG NC 34 NC NC/12V 46 6 12V
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 12V
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 12V
NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 12V
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 12V
NC 39 HUS_GND NC(ABL_HOT0)/12V 51 1 12V
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21 1-819-812-11
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE/FI-RE51S-HF
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
WOW_L 3 3
WOBT_L 4 4 CN3600
GND 5 5 NC/HTPDN1/ELTIMO3/POWER_ON 1
VCC 6 6 CN8004 NC/LOCKN1/ABL_PHT/READY 2
VCC 7 7 3 BLK#28 1 CAMERA_5V NC/SDA/PANEL_ERROR/PANEL ON 3
VCC 8 8 3 RED#28 2 CAMERA_USB_M NC/SCL/PANEL ERROR 4
GND 9 9 3 CAMERA_USB_P SPI_CS 5
GND 10 10 4 ID (GND/CLK/CAM_POP) : Connect GND via R=0 Ohm SPI_CK 6
VSYNC 11 12 5 GND_S NC/RESETX 7
GND 12 11 3 Shield 1-822-265-21 NC 8
GND 13 13 ACON Mini-USB NC 9
DM 14 14 3 WHT#28 NC 10
DP 15 16 3 GRN#28 NC 11
1-819-332-11 1-819-502-11 VCA/(SPI_SEL0) 12
JST SM15B-GHS-TB(LF)(SN)
GHR-15V-S CN9000 BUS_SW 13
NC 30 DIGITAL_STBY SPI_DI/(WDT) 14
2 29 DC_DIMMER SPI_DO 15
3 28 BL_ON/ICSPCLK SPI_ENB 16
4 27 PWM_DIMMER GND 17
BT 5 26 STBY_3.3V VBTX15P 18
6 25 BLINKING VBTX15N 19
Antena NC 24 AC_OFF_DET GND 20
8 23 BL_ERR VBTX14P 21
9 22 POWER_ON/ICSPDAT VBTX14N 22
10 21 GND GND 23
11 20 GND VBTX13P 24
12 19 GND VBTX13N 25
13 18 REG12V_Audio GND 26
14 17 REG12V VBTX12P 27
15 16 REG12V_Audio VBTX12N 28
16 15 REG12V GND 29
NC 14 REG12V_Audio VBTX11P 30
18 13 REG12V VBTX11N 31
NC 12 GND GND 32
20 11 GND VBTX10P 33
21 10 TCON_GND/VPP_PIC VBTX10N 34
22 9 GND GND 35
23 8 TCON_GND VBTX9P 36
24 7 TCON_ON VBTX9N 37
25 6 TCON_VCC12V GND 38
26 5 TCON_VCC12V VBTX8P 39
27 4 TCON_VCC12V VBTX8N 40
NC 3 TCON_VCC12V GND 41
NC 2 GND 1-843-699-11
NC 1 GND FFC Direct Connector :IPEX
1-843-925-11 1-843-917-11 or Yamaichi 1-843-708-XX
PBDP-30V-S JST SM30B-PBDSS-TF
CN8301
TM_SCL 1
TM_SDA 2
GND 3
TM_SPI1_SCK 4
TM_SPI1_MOSI 5
TM_SPI1_nSS 6
GND 7
TM_EMIT 8
BL_TYPE 9
TM_SPI0_SCK 10
TM_SPI0_MOSI 11
TM_SPI0_nSS 12
GND 13
TM_SPI_SYNC 14
TM_MODE0 15
TM_MODE1 16
TM_RDY 17
TM_LOG_RX 18
TM_LOG_TX 19
SA_MODE 20
VLEDPWM1 21
VLEDPWM0 22
CN7706 Reserve 23
1 GND_D BL_ON 24
2 +5.0V_AUDIO 0-336-971-01
3 GND_D FFC 24pin IRISO
4 X_SYSTEM_RST or Hirose FH52-24S-0.5SH
5 X_DAMP_MUTE
6 X_AMP_ERR_DET
7 X_DAMP_RESET
8 I2C_C_SCL
9 I2C_C_SDA
10 DC_OFF_DET
SPEAKER L+ 1 4 11 DAUOA_DAT3
Front L- 2 3 12 DAUOA_DAT2
Lch JST SMP-02VF-N 13 DAUOA_DAT1
1-784-991-21 14 DAUOA_DAT0
15 DAUOA_LRCK
16 GND_D
SPEAKER R+ 1 1 17 DAUOA_BCK
Front R- 2 2 18 GND_D
Rch JST SMP-02VF-N 19 DAUOA_MCK
1-784-991-21 20 GND_D
1-819-407-71
IMSA-9637S-40-Y801
or Hirose FH52-20S-0.5SH

GL6 Board

CN6401
1-842-551-11
SJM20-28WLB/JAM
DIGITAL_STBY 1 NC
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 NC CN7700
BL_ERR 8 23 #24 1 1 SP_MAIN_RP
POWER_ON 9 22 #24 2 2 SP_MAIN_RN
GND 10 21 #22 #24 2 3 SP_MAIN_LN
GND 11 20 #22 #24 1 4 SP_MAIN_LP
GND 12 19 #22 1-842-593-11 1-842-566-12
REG12V 13 18 #22 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
REG12V 14 17 #22
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 10 #22
GND 22 9 #22
TCON_GND 23 8 #22
TCON_ON 24 7
TCON_VCC12V 25 6 #22
TCON_VCC12V 26 5 #22
TCON_VCC12V 27 4 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11

CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
1-839-678-21

CN6801
1-822-360-11
53426-0510 Molex
NC 1
+OUT1 2 To LS
NC(No land) 3
NC(No land) 4
-OUT1 5
1-822-327-11
51103-0500
DIAGRAMS

159
 (Only Interface between board and board）

SM (FY14) BAX_F Board

BMFW Board CN3601 To BMFW T-con Board
CN203 GND 1 51 GND
1-798-511-11(ALPS)/ HUS_GND 1 19 VBTX7P 2 50 RxP7 (SDC)
1-798-510-12(NOBLE) HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 PANEL FFC
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
5 5 WIFI_GND VBTX2P 17 35 RxP2
6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
9 9 WIFI_GND VBTX1N 21 31 RxN1
10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
11 12 BT_3D_LR VBTX0N 24 28 RxN0
13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
USB 15 16 WIFI_USB_P GND 28 24 GND
NC 17 NC GND 29 23 SDC Use
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 SDC Use
1 19 CAM_GND BITSEL 31 21 SDC Use
CN001 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 B_INT (High:Write / L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L 5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA
GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 3D_EN
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 3D_Sync_In
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 SDC Use
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 NC
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 NC

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
JAM SYT10-12WS SYT10-12HG NC 34 NC NC/12V 46 6 NC
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 NC
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 NC
NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 NC
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 NC
NC 39 HUS_GND NC(ABL_HOT0)/12V 51 1 NC
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21 1-819-812-11
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE/FI-RE51S-HF
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
WOW_L 3 3
WOBT_L 4 4 CN3600 To BMFL
GND 5 5 NC/HTPDN1/ELTIMO3/POWER_ON 1 41 SDC Use
VCC 6 6 CN8004 NC/LOCKN1/ABL_PHT/READY 2 40 SDC Use
VCC 7 7 3 BLK#28 1 CAMERA_5V NC/SDA/PANEL_ERROR/PANEL ON 3 39 SDC Use
VCC 8 8 3 RED#28 2 CAMERA_USB_M NC/SCL/PANEL ERROR 4 38 SDC Use
GND 9 9 3 CAMERA_USB_P SPI_CS 5 VbyOne-FFC 37 NC (SPI_CS)
GND 10 10 4 ID (GND/CLK/CAM_POP) : Connect GND via R=0 Ohm SPI_CK 6 36 NC (SPI_CK)
VSYNC 11 12 5 GND_S NC/RESETX 7 35 SDC Use
GND 12 11 3 Shield 1-822-265-21 NC 8 34 SDC Use
GND 13 13 ACON Mini-USB NC 9 33 SDC Use
DM 14 14 3 WHT#28 NC 10 32 SDC Use
DP 15 16 3 GRN#28 NC 11 31 SDC Use
1-819-332-11 1-819-502-11 VCA/(SPI_SEL0) 12 30 NC
JST SM15B-GHS-TB(LF)(SN)
GHR-15V-S CN9000 BUS_SW 13 41pin FFC 29 NC
NC 30 DIGITAL_STBY SPI_DI/(WDT) 14 28 NC
2 29 DC_DIMMER SPI_DO 15 27 NC
3 28 BL_ON/ICSPCLK SPI_ENB 16 26 NC
4 27 PWM_DIMMER GND 17 25 GND
BT 5 26 STBY_3.3V VBTX15P 18 24 RxP15
6 25 BLINKING VBTX15N 19 23 RxN15
Antena NC 24 AC_OFF_DET GND 20 22 GND
8 23 BL_ERR VBTX14P 21 21 RxP14
9 22 POWER_ON/ICSPDAT VBTX14N 22 20 RxN14
10 21 GND GND 23 19 GND
11 20 GND VBTX13P 24 18 RxP13 J110
12 19 GND VBTX13N 25 17 RxN13 GND Ground 1 21 AWG#22
13 18 REG12V_Audio GND 26 16 GND GND Ground 2 23 AWG#22
14 17 REG12V VBTX12P 27 15 RxP12 PWR Power V12 IN 3 NC
15 16 REG12V_Audio VBTX12N 28 14 RxN12 PWR Power V12 IN 4 25 AWG#22
16 15 REG12V GND 29 13 GND PWR Power V12 IN 5 27 AWG#22
NC 14 REG12V_Audio VBTX11P 30 12 RxP11 1-822-322-11 1-820-264-11
18 13 REG12V VBTX11N 31 11 RxN11 JST SM05B-PASS-TBT(LF)(SN) PAP-05V-S
NC 12 GND GND 32 10 GND
20 11 GND VBTX10P 33 9 RxP10
NC 10 TCON_GND/VPP_PIC VBTX10N 34 8 RxN10
22 9 GND GND 35 7 GND
NC 8 TCON_GND VBTX9P 36 6 RxP9
24 7 TCON_ON VBTX9N 37 5 RxN9
NC 6 TCON_VCC12V GND 38 4 GND
26 5 TCON_VCC12V VBTX8P 39 3 RxP8
NC 4 TCON_VCC12V VBTX8N 40 2 RxN8
NC 3 TCON_VCC12V GND 41 1 GND
NC 2 GND 1-843-699-11 1-819-564-11
NC 1 GND FFC Direct Connector :IPEX JAE/FI-RE41S-HF
1-843-925-11 1-843-917-11 or Yamaichi 1-843-708-XX
PBDP-30V-S JST SM30B-PBDSS-TF
CN8301
TM_SCL 1
TM_SDA 2
GND 3
TM_SPI1_SCK 4
TM_SPI1_MOSI 5
TM_SPI1_nSS 6
GND 7
TM_EMIT 8
BL_TYPE 9
TM_SPI0_SCK 10
TM_SPI0_MOSI 11
TM_SPI0_nSS 12
GND 13
TM_SPI_SYNC 14
TM_MODE0 15
TM_MODE1 16
XBR-55X805C, 807C, 809C, 810C (120 Hz: UC2/LA8/AR4/CO1/ECU)

TM_RDY 17
TM_LOG_RX 18
TM_LOG_TX 19
SA_MODE 20
VLEDPWM1 21
VLEDPWM0 22
CN7706 Reserve 23
1 GND_D BL_ON 24
2 +5.0V_AUDIO 0-336-971-01
3 GND_D FFC 24pin IRISO
4 X_SYSTEM_RST or Hirose FH52-24S-0.5SH
5 X_DAMP_MUTE
6 X_AMP_ERR_DET
7 X_DAMP_RESET
8 I2C_C_SCL
9 I2C_C_SDA
10 DC_OFF_DET
SPEAKER L+ 1 4 11 DAUOA_DAT3
Front L- 2 3 12 DAUOA_DAT2
Lch JST SMP-02VF-N 13 DAUOA_DAT1
1-784-991-21 14 DAUOA_DAT0
15 DAUOA_LRCK
16 GND_D
SPEAKER R+ 1 1 17 DAUOA_BCK
Front R- 2 2 18 GND_D
Rch JST SMP-02VF-N 19 DAUOA_MCK
1-784-991-21 20 GND_D
1-819-407-71
IMSA-9637S-40-Y801
or Hirose FH52-20S-0.5SH

GL6 Board

CN6401
1-842-551-11
SJM20-28WLB/JAM
DIGITAL_STBY 1 NC
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 NC CN7700
BL_ERR 8 23 #24 1 1 SP_MAIN_RP
POWER_ON 9 22 #24 2 2 SP_MAIN_RN
GND 10 21 #22 #24 2 3 SP_MAIN_LN
GND 11 20 #22 #24 1 4 SP_MAIN_LP
GND 12 19 #22 1-842-593-11 1-842-566-12
REG12V 13 18 #22 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
REG12V 14 17 #22
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 1 #22
GND 22 9 #22
TCON_GND 23 2 #22
TCON_ON 24 7
TCON_VCC12V 25 4 #22
TCON_VCC12V 26 5
TCON_VCC12V 27 5 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11

CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
1-839-678-21

CN6801
1-822-360-11
53426-0510 Molex
NC 1
+OUT1 2 To LS
NC(No land) 3
NC(No land) 4
-OUT1 5
1-822-327-11
51103-0500
DIAGRAMS

160
 (Only Interface between board and board）

SM (FY14) BAX_F Board

BMFW Board CN3601 To BMFW T-con Board
CN203 GND 1 51 GND
1-798-511-11(ALPS)/ HUS_GND 1 19 VBTX7P 2 50 RxP7 (SDC)
1-798-510-12(NOBLE) HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 PANEL FFC
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
5 5 WIFI_GND VBTX2P 17 35 RxP2
6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
9 9 WIFI_GND VBTX1N 21 31 RxN1
10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
11 12 BT_3D_LR VBTX0N 24 28 RxN0
13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
KD-55X8005C (60 Hz: BR6)

USB 15 16 WIFI_USB_P GND 28 24 GND

NC 17 NC GND 29 23 SDC Use
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 SDC Use
1 19 CAM_GND BITSEL 31 21 SDC Use
CN001 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 B_INT (High:Write / L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L 5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA
GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 3D_EN
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 3D_Sync_In
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 SDC Use
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 12V

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 12V
JAM SYT10-12WS SYT10-12HG NC 34 NC NC/12V 46 6 12V
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 12V
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 12V
NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 12V
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 12V
NC 39 HUS_GND NC(ABL_HOT0)/12V 51 1 12V
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21 1-819-812-11
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE/FI-RE51S-HF
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
WOW_L 3 3
WOBT_L 4 4 CN3600
GND 5 5 NC/HTPDN1/ELTIMO3/POWER_ON 1
VCC 6 6 CN8004 NC/LOCKN1/ABL_PHT/READY 2
VCC 7 7 3 BLK#28 1 CAMERA_5V NC/SDA/PANEL_ERROR/PANEL ON 3
VCC 8 8 3 RED#28 2 CAMERA_USB_M NC/SCL/PANEL ERROR 4
GND 9 9 3 CAMERA_USB_P SPI_CS 5
GND 10 10 4 ID (GND/CLK/CAM_POP) : Connect GND via R=0 Ohm SPI_CK 6
VSYNC 11 12 5 GND_S NC/RESETX 7
GND 12 11 3 Shield 1-822-265-21 NC 8
GND 13 13 ACON Mini-USB NC 9
DM 14 14 3 WHT#28 NC 10
DP 15 16 3 GRN#28 NC 11
1-819-332-11 1-819-502-11 VCA/(SPI_SEL0) 12
JST SM15B-GHS-TB(LF)(SN)
GHR-15V-S CN9000 BUS_SW 13
NC 30 DIGITAL_STBY SPI_DI/(WDT) 14
2 29 DC_DIMMER SPI_DO 15
3 28 BL_ON/ICSPCLK SPI_ENB 16
4 27 PWM_DIMMER GND 17
BT 5 26 STBY_3.3V VBTX15P 18
6 25 BLINKING VBTX15N 19
Antena NC 24 AC_OFF_DET GND 20
8 23 BL_ERR VBTX14P 21
9 22 POWER_ON/ICSPDAT VBTX14N 22
10 21 GND GND 23
11 20 GND VBTX13P 24
12 19 GND VBTX13N 25
13 18 REG12V_Audio GND 26
14 17 REG12V VBTX12P 27
15 16 REG12V_Audio VBTX12N 28
16 15 REG12V GND 29
NC 14 REG12V_Audio VBTX11P 30
18 13 REG12V VBTX11N 31
NC 12 GND GND 32
20 11 GND VBTX10P 33
21 10 TCON_GND/VPP_PIC VBTX10N 34
22 9 GND GND 35
23 8 TCON_GND VBTX9P 36
24 7 TCON_ON VBTX9N 37
25 6 TCON_VCC12V GND 38
26 5 TCON_VCC12V VBTX8P 39
27 4 TCON_VCC12V VBTX8N 40
NC 3 TCON_VCC12V GND 41
NC 2 GND 1-843-699-11
NC 1 GND FFC Direct Connector :IPEX
1-843-925-11 1-843-917-11 or Yamaichi 1-843-708-XX
PBDP-30V-S JST SM30B-PBDSS-TF
CN8301
TM_SCL 1
TM_SDA 2
GND 3
TM_SPI1_SCK 4
TM_SPI1_MOSI 5
TM_SPI1_nSS 6
GND 7
TM_EMIT 8
BL_TYPE 9
TM_SPI0_SCK 10
TM_SPI0_MOSI 11
TM_SPI0_nSS 12
GND 13
TM_SPI_SYNC 14
TM_MODE0 15
TM_MODE1 16
TM_RDY 17
TM_LOG_RX 18
TM_LOG_TX 19
SA_MODE 20
VLEDPWM1 21
VLEDPWM0 22
CN7706 Reserve 23
1 GND_D BL_ON 24
2 +5.0V_AUDIO 0-336-971-01
3 GND_D FFC 24pin IRISO
4 X_SYSTEM_RST or Hirose FH52-24S-0.5SH
5 X_DAMP_MUTE
6 X_AMP_ERR_DET
7 X_DAMP_RESET
8 I2C_C_SCL
9 I2C_C_SDA
10 DC_OFF_DET
SPEAKER L+ 1 4 11 DAUOA_DAT3
Front L- 2 3 12 DAUOA_DAT2
Lch JST SMP-02VF-N 13 DAUOA_DAT1
1-784-991-21 14 DAUOA_DAT0
15 DAUOA_LRCK
16 GND_D
SPEAKER R+ 1 1 17 DAUOA_BCK
Front R- 2 2 18 GND_D
Rch JST SMP-02VF-N 19 DAUOA_MCK
1-784-991-21 20 GND_D
1-819-407-71
IMSA-9637S-40-Y801
or Hirose FH52-20S-0.5SH

GL6 Board

CN6401
1-842-551-11
SJM20-28WLB/JAM
DIGITAL_STBY 1 NC
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 NC CN7700
BL_ERR 8 23 #24 1 1 SP_MAIN_RP
POWER_ON 9 22 #24 2 2 SP_MAIN_RN
GND 10 21 #22 #24 2 3 SP_MAIN_LN
GND 11 20 #22 #24 1 4 SP_MAIN_LP
GND 12 19 #22 1-842-593-11 1-842-566-12
REG12V 13 18 #22 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
REG12V 14 17 #22
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 10 #22
GND 22 9 #22
TCON_GND 23 8 #22
TCON_ON 24 7
TCON_VCC12V 25 6 #22
TCON_VCC12V 26 5 #22
TCON_VCC12V 27 4 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11

CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
1-839-678-21

CN6801
1-822-360-11
53426-0510 Molex
NC 1
+OUT1 2 To LS
NC(No land) 3
NC(No land) 4
-OUT1 5
1-822-327-11
51103-0500
DIAGRAMS

161
 (Only Interface between board and board）

SM (FY14) BAX_F Board

BMFW Board CN3601 To BMFW T-con Board
CN203 GND 1 51 GND
1-798-511-11(ALPS)/ HUS_GND 1 19 VBTX7P 2 50 RxP7 (LGD)
1-798-510-12(NOBLE) HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 PANEL FFC
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
5 5 WIFI_GND VBTX2P 17 35 RxP2
6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
9 9 WIFI_GND VBTX1N 21 31 RxN1
10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
11 12 BT_3D_LR VBTX0N 24 28 RxN0
13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
USB 15 16 WIFI_USB_P GND 28 24 GND
NC 17 NC GND 29 23 AGP/NSB (High/Open:AGP, Low: NSB)
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 NC
1 19 CAM_GND BITSEL 31 21 NC (BITSEL(High/Open:10Bit; L:8Bit))
CN001 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 nWP (High:Write; L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L 5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA
GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 PCID_EN (High: Enable, Low/Open: Disable)
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 NC
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 NC
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 NC
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 NC
JAM SYT10-12WS SYT10-12HG NC 34 NC/12V 46 6 NC

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C
NC
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 NC
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 NC
NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 NC
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 NC
NC 39 HUS_GND NC(ABL_HOT0)/12V 51 1 NC
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21 1-819-812-11
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE/FI-RE51S-HF
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
WOW_L 3 3
XBR-65X800C, 805C, 807C, 809C, 810C

WOBT_L 4 4 CN3600 To BMFL

GND 5 5 NC/HTPDN1/ELTIMO3/POWER_ON 1 41 NC
VCC 6 6 CN8004 NC/LOCKN1/ABL_PHT/READY 2 40 NC
VCC 7 7 3 BLK#28 1 CAMERA_5V NC/SDA/PANEL_ERROR/PANEL ON 3 39 NC
VCC 8 8 3 RED#28 2 CAMERA_USB_M NC/SCL/PANEL ERROR 4 38 NC
GND 9 9 3 CAMERA_USB_P SPI_CS 5 VbyOne-FFC 37 NC
GND 10 10 4 ID (GND/CLK/CAM_POP) : Connect GND via R=0 Ohm SPI_CK 6 36 NC
VSYNC 11 12 5 GND_S NC/RESETX 7 35 NC
GND 12 11 3 Shield 1-822-265-21 NC 8 34 NC
GND 13 13 ACON Mini-USB NC 9 33 NC
DM 14 14 3 WHT#28 NC 10 32 NC
DP 15 16 3 GRN#28 NC 11 31 NC
1-819-332-11 1-819-502-11 VCA/(SPI_SEL0) 12 30 NC
JST SM15B-GHS-TB(LF)(SN)
GHR-15V-S CN9000 BUS_SW 13 41pin FFC 29 NC
NC 30 DIGITAL_STBY SPI_DI/(WDT) 14 28 NC
2 29 DC_DIMMER SPI_DO 15 27 HTPDN (LGD Use Only)
3 28 BL_ON/ICSPCLK SPI_ENB 16 26 LOCKN (LGD Use Only)
4 27 PWM_DIMMER GND 17 25 GND
BT 5 26 STBY_3.3V VBTX15P 18 24 RxP15
6 25 BLINKING VBTX15N 19 23 RxN15
Antena NC 24 AC_OFF_DET GND 20 22 GND
8 23 BL_ERR VBTX14P 21 21 RxP14
9 22 POWER_ON/ICSPDAT VBTX14N 22 20 RxN14
10 21 GND GND 23 19 GND
11 20 GND VBTX13P 24 18 RxP13 J110
12 19 GND VBTX13N 25 17 RxN13 GND Ground 1 21 AWG#22
13 18 REG12V_Audio GND 26 16 GND GND Ground 2 23 AWG#22
14 17 REG12V VBTX12P 27 15 RxP12 PWR Power V12 IN 3 NC
15 16 REG12V_Audio VBTX12N 28 14 RxN12 PWR Power V12 IN 4 25 AWG#22
16 15 REG12V GND 29 13 GND PWR Power V12 IN 5 27 AWG#22
NC 14 REG12V_Audio VBTX11P 30 12 RxP11 1-822-322-11 1-820-264-11
18 13 REG12V VBTX11N 31 11 RxN11 JST SM05B-PASS-TBT(LF)(SN) PAP-05V-S
NC 12 GND GND 32 10 GND
20 11 GND VBTX10P 33 9 RxP10
NC 10 TCON_GND/VPP_PIC VBTX10N 34 8 RxN10
22 9 GND GND 35 7 GND
NC 8 TCON_GND VBTX9P 36 6 RxP9
24 7 TCON_ON VBTX9N 37 5 RxN9
NC 6 TCON_VCC12V GND 38 4 GND
26 5 TCON_VCC12V VBTX8P 39 3 RxP8
NC 4 TCON_VCC12V VBTX8N 40 2 RxN8
NC 3 TCON_VCC12V GND 41 1 GND
NC 2 GND 1-843-699-11 1-819-564-11
NC 1 GND FFC Direct Connector :IPEX JAE/FI-RE41S-HF
1-843-925-11 1-843-917-11 or Yamaichi 1-843-708-XX
PBDP-30V-S JST SM30B-PBDSS-TF
CN8301
TM_SCL 1
TM_SDA 2
GND 3
TM_SPI1_SCK 4
TM_SPI1_MOSI 5
TM_SPI1_nSS 6
GND 7
TM_EMIT 8
BL_TYPE 9
TM_SPI0_SCK 10
TM_SPI0_MOSI 11
TM_SPI0_nSS 12
GND 13
TM_SPI_SYNC 14
TM_MODE0 15
TM_MODE1 16
TM_RDY 17
TM_LOG_RX 18
TM_LOG_TX 19
SA_MODE 20
VLEDPWM1 21
VLEDPWM0 22
CN7706 Reserve 23
1 GND_D BL_ON 24
2 +5.0V_AUDIO 0-336-971-01
3 GND_D FFC 24pin IRISO
4 X_SYSTEM_RST or Hirose FH52-24S-0.5SH
5 X_DAMP_MUTE
6 X_AMP_ERR_DET
7 X_DAMP_RESET
8 I2C_C_SCL
9 I2C_C_SDA
10 DC_OFF_DET
SPEAKER L+ 1 4 11 DAUOA_DAT3
Front L- 2 3 12 DAUOA_DAT2
Lch JST SMP-02VF-N 13 DAUOA_DAT1
1-784-991-21 14 DAUOA_DAT0
15 DAUOA_LRCK
16 GND_D
SPEAKER R+ 1 1 17 DAUOA_BCK
Front R- 2 2 18 GND_D
Rch JST SMP-02VF-N 19 DAUOA_MCK
1-784-991-21 20 GND_D
1-819-407-71
IMSA-9637S-40-Y801
or Hirose FH52-20S-0.5SH

GL6 Board

CN6401
1-842-551-11
SJM20-28WLB/JAM
DIGITAL_STBY 1 NC
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GB Harness
BLINKING 6 25
AC_OFF_DET 7 NC CN7700
BL_ERR 8 23 #24 1 1 SP_MAIN_RP
POWER_ON 9 22 #24 2 2 SP_MAIN_RN
GND 10 21 #22 #24 2 3 SP_MAIN_LN
GND 11 20 #22 #24 1 4 SP_MAIN_LP
GND 12 19 #22 1-842-593-11 1-842-566-12
REG12V 13 18 #22 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
REG12V 14 17 #22
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 1 #22
GND 22 9 #22
TCON_GND 23 2 #22
TCON_ON 24 7
TCON_VCC12V 25 4 #22
TCON_VCC12V 26 5
TCON_VCC12V 27 5 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11

CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
1-839-678-21

CN6801
1-822-360-11
53426-0510 Molex
NC 1
+OUT1 2 To LS
NC(No land) 3
NC(No land) 4
-OUT1 5
1-822-327-11
51103-0500
DIAGRAMS

162
 DIAGRAMS

4-3. PC BOARD DIAGRAM

BMFW (A SIDE)

TP3109
cam9 cam013 cam5
C7746 C7747 C7748 C7749 CN7706 CN3601 CN3600 CN8301
CN1000 cam011
cam804 C3152
CN7704 CN7700
CN7705 Q9027 CN9000
cam025 IC3103
cam39
cam097 cam904 CL3627
CL3623
CL3625 CL3616
CL3617
CL3618
CL3620
CL3621 CL3615
CL3614
CL1007
C1068 CL1008
cam034 CL1006 D9002Q9028
R9093
CL3631
CL3633 CL3628
CL3626CL3622
CL3619
CL3659
CL3624 CL8309
cam012 L7704 L7705 L7706 L7707 C7878 C7766C7765 C1067 R3653 CL3640 CL3630 JC3607 JC3606 JC3605 JC3604
CL3636CL3632
CL3638 JC3603 JC3602 JC3601 JC3600 C3685C3684
RB1000CL1003 VD1000 R1080 R3332
R3331 R3333
R3330 R3336
R7980 R1091 C1062 C1079 C3683 C3682
R3627
R7930 R7921
TP3111 R1109
C1071
C1072C1064C1073 C1075C1078
R3652 CL3642
CL3643 CL3639
CL3641 CL3635 CL3629
CL3637 C3692 C3688
C3693 C3686
C3687 R3630R3672
R7927 R7920 R1075 R1088 R1079 C1061 R1062 R3685
R3684 R3679 CL3654 cam024
VD1001 cam26 Q9029 Q9030 R9188
R9021
C8355 C8361
C8362 C8354 C8352
C8353 C8350
C8351C8349C8347
C8348 C8346C8344
C8345
C8343 C8341
C8342 C8339
C8340
R7931
R7978 C1070CL1004
CL1005C1065 D1003 R1085R1107
R1082 R3716
R3694
R3695 C3701
R3693
C3712
R3703C3694
R3702 R3636 R3675
R3635
R3705
R3680
R3701 R3673
R3674 R3632
R3631 R3629R3633
R3628 R3634
R3671R3670 C9020
R3327
R3326
R3328
R3329
cam032 C7865 C3700
C3699
C3698 R3704
C3713
IRM001 C7877
R7926 R1128 C1057
R1090 R1073
C1082 C3704 R3691 C9017 C9119 C9011 C9009
C7782 C7781C7780 C7779C7720 C7719C7718 C7709 R1450 CL3610 CL3655
CL3660 C9015R9181
R9018 C9027
R9027R9004
R9026R9025
R9024 C9016
R8359
R8398 R8358
R8397 R8356
R8357 R8355
R8354R8352
R8353R8351
R8350 R8347
R8348
R8349
R8393 R8346
R8345
R8344
R7923R7922 R1127 R1077C1066 R1078
R1076 C1056
R1089 C1077 C3695
C3696
C3697 R9022
R9023
R3334
C7752 C7753 C7750 C7751 C1074 C1076R1084 C3702
R3645 R3641
R3642 R3688
R3689
R3690 CM3102
R1105R1106 VD1002 R9092 C9030 L9000 R9144R9028 R8382
CM8300 R3335
CM3103
C1083 R1086 R1081
R1087 R3683
R3687 R3682
C1055 R1083 CL3609
R3692R3647 CL3608
CL3607 R9208 C9026
C9025C9023
C9013C9021
C9018
R1129R1126R1108 CL3612CL3611 CL3606
R3686
D1002 R3640R3638
R3639 Q9020 C9151
C7745 D1001 R3644R3643 R3646 Q9021R9216 R9186
R9187 R9182 CN8004
KA001 R3637 R9215R9213
R9214 R9209
R9211
R9212 IC9018 C8033
R3626R3625 R3649 R3648 R9185
C9118 IC8003 C8025C8041C8023
C8024
D3601
D3600 VD8007
R8028
C7742 C7743 R9183Q9015 Q9016
R9166
R9168
R9194 C8027
C7714 C7715 C7716 C7744 R9154 S3602
L9403 cam806 R9184 cam802
C7717 C9117R9156R9178R9180
cam217 Q3601 Q3600 cam801
R3651
R3650 F9406 C9440 C8026cam803 R8030
R9155
R9179 R9163
C9443 C9442 IC8004
C7873 C7874 R3714R3715 Q9017 R8029
R7932 R9157 C9450
R9210 R9164 C9441
C7731 R7766 L7700 C7703 C7701 R9177 C9444 R9447
L7701 R7933 CL8001
CL8002
R7934 IC9017 R9165 R8341 R9448
L7702 L7703 C9445
R9158
R9167
R9169 R8394
R8395 IC9406 JC8002
R7935 R9066
TP3106 R9176 R9065 R9064
IC7700 R7936 C9062 R9062 R9051
cam179 C8335
R8343C8337C8332
C8336
F9005 F9000
R9161 R9060 R9129C9069 C9126
R9175R9159
R9173 R9170 CL3658 ET035
C7728 R9162
R9172 C9070 C9448 C9420C9409
C9421 R8336 cam091
C7729 CL5302 R9174 Q9022 C9068 L9001 R8338
R8337 R8396
R8340C8338 C8322
C8333C8327
C7727 R9090 C9127 CL8717 R9445R9444C9439
Q9023 IC9008
C7730 C9047 C9048 C9049 C9050
C9129 C9128 cam087
R8333 R8339R8323
R8388
R8387 R8328 R9443 C9447
C7711 R7758 C7875 C7876 R9091 C9065 R9413 CL8716 TP3108
cam058 R7750
R7967R7751
R7752 R9153 C9051 IC9003 ET036 R8334
C7706 F7700 R1173 R9171 R9412 L9401 cam035 C9446
R9442
C7708 R7767 IC9401 IFM002 CL8715C8334
R8335
C7741 C8360 CL3656
CL3657
C7863 C7704 F7702 R9409
R7748
R7760 R7761R7749 cam019
R8399 C1037
C1035 C9133
R7728 R9034 R9410
C7700 C7702 R1007 R1006 C9088 C9081
C9085
C9086 C9116
C9075 R9198
R9197 CL3605
R3613
C8307
C8317
C7707
C7710 R1038 R1037 C9122
R9201
R9199 C9124C9130
C9123 R9035 C9419
R9411
R9408 C9410
IFM003 C3142 R3168CL3112
IC7701 C1428
C1425 C8359R1039 C9451 R9421 C3654
C3653C3650
C3649C3646 C3641C3638
C3645C3642 C3633C3630
C3637C3634 C3629C3626
C3625
C8358
C1415 R3159 C3145 R3173 R3601 CM9400
FL9400R9450
R9449R8318
cam103 L9004 R9200
cam578 C9131 R9037 R8308C8308
C8310
C8303C8301
C8304
KA003 cam095 C1039 C9411 C9414 C3146R3174
C1411 CL5220
R5486 R9420 C3119 R3123
R1429
R1433 R1142 C3656
C3655C3652
C3651C3648
C3647C3644 C3635C3632
C3639C3636
C3643C3640 C3631 C3628
C3627
C1041
R1122 R9085
R9084 R9086 C3110R3121 R3314 R3199 R3160 C3601 CM3001
R3004
R1503 R9087 R9089
R9088 C9132 CM9006 R9419
R8701 C9415 C3112R3112 R3600R3177 CL3003
C1433
R1040 R1111
C1026 C9412 C3117 R3113 C3401C8312 R8304
R8309
C8302 R8311R8305
R8302
cam059 R7757 R8379
R1432 R8380 C1001 R1015
R8392 R9418 C3108R3111 CM8306
R8385
R8386
R1460 C3030
C7713 R7759 C9416 C3122 C3114R3122 RB3412 RB3411
cam100 cam003 R7755
R7729R7756 R1427 R1019 R1016 C1030 C9413 R9417 R9434 R3602CL3601 CL3600 C3123 C3201 R8303
R8313C8324C8311
C8309 C8300C8323
C8306
C8305 R8324
C7712 R1401 R1400 R3158R3124 R9437 C9435
C1034 C3027
R7763 C7705 C1414
C1400 R9029 R9039 C9046 C9045 C9417 R9416 IC9404
C7864 R7753
R7764R7754 C1416 C1419 R1017R1102 R3603 RB3410 RB3409 RB3408
C1417 R9045 C9433 CL3602
R7968 R1420 R1500 R1499R1438 C1004 R1018 R9030 R9038 R9415 cam089 R8325 R8307
R8306
R8312
R8310 R8300
R8301R8389 RB3405 RB3404
R1425 C1000 cam079 C9418 C9434 R9435 CL8323
R1419 R1439 C1407 R1021R1118 C3657
R1506 R9043 IC9004 R9046 R8383 R3180 CL3603 CL8319
CL8324 R3403
cam101 C1002 R9414
R1434 R1020 F9401 R8384R8391 Q8301
CM8301 Q8300 C3150 R9436
R1130 R9044 CL8322 CL8320
CL8317 RB3403 RB3402 RB3401
R8378 R8390
R1131 C8357 C3001 C3005 CL8311
CL8321 C3448C3449C3447C3446 R3409
C3445 R3411
C3458 R3410
C3457 C3444
R2016R2012R2015 cam098 C1424
C1017C1410 X3600
C1441 C1021 R3005 C3603 CL8310
CL8315
CL8316
R1045
C1029 C3006 C3004
R8721R8704
R8722 C3028 CL3004 C3658 CL8314
R8703 C7795R7741R7740 C3000 C3022 C3614 C3602C3607 C3617
cam102 RB3400 RB3407
C1013 R1417
R1042
R1421 C7801R7789R7788 C3011 C3612 C3616C3605 C3620 R3611 R3620
IC1400 R2004 R1043C1406 D8700 D8701 C3016 C3018 R3615 C3443
C3714
C2001 R3711
C7796R7743R7742 FL3000 CL3000 C3007 C3017 C3025 C3606 C3619C3604 C3624 R3617
cam178 IC2002 C2018 R8377 R3710 C7802R7791R7790 C3012 C3021 C3026 C3608 C3610C3615 C3609 C3450
C3508
RB3406
C2016 R2003
C2015 R1041 C1426
R1422 C1404
C1402 R1412R1465 C1024 IC3600 C3202 C3207
R1117 C8356 R3706 R3707 C7800R7787R7786 C3029 C3023 C3623C3613 C3611
C2021 R1413R1464 R1463 R1034 C3205 C3203
CM3601
R3709 CM3600
R3708 C7794R7739R7738 C3622C3125
R2005 R2013 RB2001 RB2003 C1020 C3031 IC3401
cam046 C2019 C1408C1436 R1462 R1116 R3713 R3712 R7727 C3034 C3036 C3402 C3204
cam085
IC2001 R1416
R1423
R1424 R1033 cam213 C7799R7785R7784 CL7714
R7855 C3032 C3618C3127 C3403 C3407
C1412C1434
R8702 C3033 C3035 C3020
C2022R2017 C1016 R3696 C7793R7737R7736 C3002 C3008 C3404 C3206
CN1403 C1430 R1032
C1432 R3622 S3600 CL7713
R7854 CL3414
R3618 C7791R7733R7732 C7797 FL3001 C3010 C3015 CL3407
RB2002 RB2004 R1445
R1444
R1454
R1453 R1115 R7726 C3003 C3405
R1063 C7798R7783R7782 C3600 CL3412
R1446
R1447 R2009R2001 cam212 cam211 R1451
R1452 R3607 R7745R7744 C3009 C3406 CL8312
R1513 R3614 C7792R7735R7734 C3621 CL8313 cam061
cam083 cam218 CL1002 R3604
R1136 IC1407 IC1406 R7731R7730 CL7761 CL3415
R1512 R1125 R3623 S3601 R3697 R3609
C2009
C2010
C2011
C2012 R2010
C2013C2014 C7879 CL7760
cam020 C1043 R3619R3608 C3062 C3063 C3456C3455C3454 C3459 C3452C3451
R1030 C3453 R3413
C1462R1515 R1514 R1516 R8713 R3616R3605 CL7759
R1137 R1510 R3412
C2002R2002 C2020C2017 R1113
C1009 R2403 C2655 FL2602C2659 FL2603 C2654 R3606 CL8714 CL7758
C1012 C3460
R1031 S8700 CL8713 CL7757
R2404
R1138 CN1400 R1054 C2223 CL8702 CL7756 C3680
R1114 R3404
C3427
C3430C3431C3429C3428 C3440
R3406 R3405
C3439 C3426
R1053 FL2601 CL7715
R7856 R8716
C2665 CL7722 R8720 C3068
C3067 C3679
C2426
C2428 C2434 R8714 CL8712 R7863 CL7720
R7861 C8744
C8743C8739
C8742
R1139 C2640C2638
C2407 C3066
C3069
C2411 S3107 R8724 R8715 CL7721
R7862 CL8718
C1032
C1028 C2635 R2414 C2401 C2637 R2402 C2639 CL8703 R7860
CL7719
R8705 R8706 CL7718
R7859 C8708 CL3403
CL8704 CL7717
R7858 C3425
R1140 C1461 C1019 R2409 R2407 R3309 CL7716
R7857 C8709 C8745
C8738 C8732
C8734
C8736 C8733 C3044
C3037
C3038 C3661
C3043 C3662
C3070 C3663
C3664
C3665
C3666 C3261
R1036
R1035 C3059 C3056
C3053 CL3413
R1449
R1448 C2406 R3312R3313 CL8705 C8710 C3432
R1026 R1112 R2405 R8707 R8708 R3308 C3046C3047
C3041 C3045
C3042
C3040 C3678
C3676
C3039 C3669 C3266
C3672
C3673
C3677
C3671 C3670 CL3406
C8711 C3057
CN7703 COM100 C2427
R2410 C2408 R2406 R8709 R8710 CL8700 CL7762 C8712 C3058
R1141 C2402 C7836
R7725 C3263
R1517 cam38 C2405 C2424 R8711 R8712 C8713 C3264 R3401R3400
C3422C3421 IC3400
Q1402 R2014 R3311 R3310 R7724 C8714 C3265 CL3411
C7764 R2412 C2603 C2663
C8715
C1463 C1006 C2415 C2662
C2224 FL2605 C8716 C3271 CL3402
C2425
R2408 C8747 CL3409
cam043 CN8003 cam049 C8717 C8749
C8750 C8748
R1022 C2610 C8718 C3475
IC1408 Q1401 C1011 C8756 C3275 CL3401 CL3408
J7701 C2664 R2411 C2403 cam038 C8719 C3474
C3276
T8001 T8000 T8002 R1119
R1024 C8720 C8755 IC3000 CL3405
C2430 C3468
C3277 CL3404 cam060
C2606 IC2401 C2409 IC2400 C8721 C8754 C3476 CL3410
R1518Q1400 R1121 C8722 C8753 C8751
C8752 C3278
cam033 C2429
C2607 C3274 C3438C3437 C3441 C3434C3433
FL2600 R2400 ET031 C8723 C3051 C3477 C3435 R3408
C3436
C2604 C2412 C8724 C3479
C3469 CL3400 R3402 R3407
C7862
R7966 C7860
VR7701
R7964 C3054 C3073
C8725 C3442
R2413 C2617 C2653 C3052
C7858 R7961 C1015 C2413 C2400 C2404
C8726
C3055
C3061
C8017 C2410 C8727 C3060
cam202 R8039 C8728 C3267
C8015 C8016 R1025
JC8704 JC8702 JC8700CL2201
C2414
C8729
C3019
C8735 C3014
C8737 C3013 C3050
C3049 C3048 C3481
C3480 C3279
C3483
C3482 C3147C3270
C3478
C3268
C7861
R7965 C7859
R7963
VR7700 RB8004 ET032 C3473
C1409 C2658 C8730 C3472C3462C3463
C3471
C3283 C3465
C3282 C3281
C3280 C3466 C3272
C3464
C3461
C3470
cam050 FL2604 C8731
C7857 R7959 cam021 C1413 C9807 C3273
C3262
JC8705 JC8703 JC8701 C8740R8718
R8717
L8000 R1501 C8741 C3269
R1402 C9802 cam028 R2213
R2214 C2231 C2222
cam203 CL3002
C1431 R1415 C2023 CM3000
R3003
cam027 C3467
R2006
R1440 C9801 C2210 C2209 R2202 C2217 C2211 C2609 R3320
R3319
C1422 R1414 C3151
C3024
C1423R1441 C7783
R1459 C1420 C9800 R3181 R3002CL3001
C1008 C2212 R3316 cam045 C3126
C8700 C3124 R3178
R2011 C9804 R3315 R3337 R3114 R3105 C3065 C3064 C3417C3415C3413
C3419 R3125C3121
R1430 C7786C7785 R1023 C2656 R3182 R3151
C3100 R3152C3101 CL3123 R3127
C1401 C7787C7784
R7721 C9803 R3324
R3323
CM3100
CM3101 CL3202 C3418C3416C3414
R1442
R1443 IC3102
C1405 R1120 C9805 C2660 R3317 CL3122 cam047 CL3201
R7715 R2007 C3134 R3305 C3507
R7719 R7720 R3318 C3130 CL3200CL3204 R3126 X3100 C3217
C3412C3216
C3420
R1437 C7788 R7717 C9806C8701
CM2200
R2217 R3136 R3135 CL3121 C3224 CL3205 R3201
CL3206CL3203
CL3207 C3209C3211C3213C3215
C3208
TP3110
R7713
R7723 R7718
R7714 C3210C3212C3214
R1435 C8703 R3129 RB3102
RB3103C3132 R3128 CL3120C3137 R3140
R3133 C3424 C3220 C3222
C3120
CL8300 R8700 IC2203 C3128 R9432
R1509 R7712 R7716 C8705C2218 CL3118 C3223 C3200 R3202 R3200
R7722 R3325
R3322
R3321 CL3119 C3221 ET037 R9431
R5476 C2003 C3138 R3167
C3139 C3423
CN7501
J7501 C1403 C2008 R3137 CL3116
C2236 C3400 R9430
C1440R1436 RB3104 R3130 R3176
C2007 C3136 C3133 C3408
C3409
C3410
C3411
R1469 C3131R3138 R3132 CL3113
C3143
C2004 CM3200
R3214
R1468 C3129R3131 R3166 R3139 R3172
C1439R1458R1457 C2006 R2212 C3135 CL3214
C1427 R3115cam044 CL3105 IFM004
R1428 C2005 R3153
C3103 CL3208
CL3209 C3232 CL3213
CL3212 C3250
R3175 R9440R9439 cam055 L9402
C9811 C2618C2661C2619 C2214 C2625 CL3106
cam023 C2213 C2215
C2208 R3190R3187R3188C3144 R3116 R3118 cam037
cam054 C3230 C3248
RB2005 R1507 C2234 R3189R3183 C3107R3117R3108 C9437 C3219 C3238 C3256 C9426
R2210 R3184
cam017 RB2006 R1431 R2201 C2626 R2209
C2201 R1601R3179R3198R3154C3111C3113
C3115 C9449
C2204 C2203 C2202 C2216 R3156R3157 C3231 C3249
R3197 C3237 C3255
R1508
C1418 ET038 C9427 C9430
C9810 FL2606
R1426 C9809
R3191R3186
R3107 CL3101
R3110
IC9405 C3229 C3247C3308
C1429
R1502 C2205 R1630
CM8303CM8302
R1629 R3192 R3120R3109 C3236 C3254
C3109 CL3211 IC9403 C9431
R1600 CL3102C3104 C3228 C3246 IFM001
R1000 R1050 IC1600 C3235 C3253
C1042
R1001 C2624 R3185 R3155C3106C3118 C9436
R9441 CL3215
R1162 C2221 CL3100 cam204 C3227C3260 C3245
R1631
CM8304CM8305
R1632 R1604 R9438 C3241
C3242
R3207 IC3200 R3212
C3259 IC3201 R3203
C1038 CL3103
cam171
R1004 R1049 C9808 CL7609 C9814
CL7608
CL7606
CL7602 R9074 C9090 R9077 R3119 R3208
R3204
R3213
R3209
C1040
R1005 R1161 C7601 C3102
VD7500 C7600 C9089R9075 IC9011C9092 C1600 CL3210 C3240 C3258 R9429 R9427 C9424
R9801 CL7605
CL7604
CL7610
R1048 IC2202
cam3 R1046 R7600 IC1000 C2666
C2620 R3206 R3211 RB3205 C9428 cam084 R9426
R7501 C1033
R1099 CL7603 CL7607 R9803
CL9802 C9091 R1636 R1637R1607 C3218 RB3212
R9428
C7500 FB7500 C8037 R9073Q9025 R3106 C3234 C3239 C3252 C3257 C9425
R1418 R8013 R9425
C9432
R7500 C1421
R1511 C3105 R3205 R3210 C9429
R1461 R7526C7513 R2206 cam016 Q3100 RB3204 RB3211
R7557 C7533 Q9026 R9076 cam096 CL3115 C3233 C3251
R1505
C1435 R7554 R7527C7515 C2623 C2226 C2423
C2227 R3307 C3226 C3244
R7537 C2627 R9069 C3307
R7551C7516 F9002 R3100D3100 RB3101 S3100 RB3100 F9403
R7556 TP3102
R7530C7518 CM9004 IC9010 R3306
R7535 C9060 RB3203 RB3210
R7553C7520 cam018 C3225 C3243
R7539 C2611 C2206 C2207 C2621 C2622 D9000 R9071
C9059 C9036 CL3114
C2200
J7504 R7504C7502 R2200C2233 C2602 C9061
R7508C7504 R2211 C2614 C2605
C2232
R2216
R2215
C2608 RB3202 RB3209
FB7501 D9001CM9005 C9033
R7507C7505 R2208 C2421 C9152 TP3105
CL2206 RB3200
R7601C7602
C7532 cam28
R7511C7507 C6303 R2207 R9070 R9000 C9031
TP3101 C2225 R9067 cam579 RB3201 RB3208
C8005
R8044C8022 R7525C7512 R9083
R9082
R9081 R9011
C1047
C8021 R1064 R9072
C9073 R9068 R9010
Q8000R8045 R7519C7511 R6035 IC9009 C9000
C2612
R2602 C9074
C9076 RB3206 RB3207 S8400
C8042
R8056 Q8001 C9087 R9005 R8422
R8421
R8017 R7515R7516 R1056 C2220 C9082
R8043R8042 C9004 IC9001 C9028 TP3112
R8018 C2219 C9114
CL8003 C8706
C8704
R8723 C8702 C8707 C2420
R2601
Q8002 C9821 C9010
VD7532 VD7501 VD7502R7538
VD7506 R7502 VD7504
VD7503 VD7507 R8058 IC2600 FL2607 C9121
VD7531VD7533 CL7501
R7520 R7536 VD7509 R7524 D8001 R1047 L9002
C7542 VD7530 D7502 C7501 D7504
R7513 D7532 D7506D7500
C7514 C1036 R9804 R2612
C7541 C7543 D7536VD7505 D7505R7509
D7501 R7534D7508 R7531
C7519 D7530 R1172R8057
R1171 C7736C7739 cam052 C8018C5605 C1050 C2634
C7540 CL7707 C8019 R2614 L9007 R9020 C9109
D7535 VD7535 C7508 D7511 R7505 R7503R7512 R7514 R7523 C7740 C8000C5604 R8014 C1052 cam040 C9042C9039
R7517
C7510 R7705 C7735 C7738 C8001 R1134 R2613 R9125 R9042 C9044
D7533
VD7534 C7545 C7506 R7532 C7517R7529
VD7508D7531 R7552
D7534 R7506
C7503 F7701 CM7702 C7737 C9812 C2652 R9041
C7544 L7500 R9124
C7548 C7509 D7510 R7518 R7510 C7732 R7802FL7700 R1052 RB7004 RB7001R1029
R1014
R1012R1057
R1135C9813 C2628 C2636 CM9000 R9040
C7549
R7577
R7574 R7576 R7533 R7599 CL6301
CL6300 CL6302
CL7502 R7522 IC7702 C1045
R1055 R8015
R7528 C7551
R7579 R6302 C1044 C8035
C8036 cam053
CL7505 R7572R7578
C7547 CL7504 R7708 R7709R7747
R7710R7746 C1031 C1046
C1022
C1014 CL2200
R1060 R2219
R9802
C7550 CL6312 RB7002
DM001
cam005 R6300
R6301
CL7503 R2615
C2651 R2604
R2605
C2629 C2616 C2615 C2601 C2600
C2613
R7707 X1000 R6314
CL6304
cam071 C6301C6300 R1044 C2228
C1051
C1025 R6313 RB7006 R1013
R1011
R1008R1058
R1059 R2611
C7546 R7706
CL7705 R6318 C2422
R6326
R6327 R1003 C6304 R2610 ET033
R1133
R1100 C2419 C2416 C2230 C2418 C2417
R1002 R6315 R7022R7017
C7734 C7733 CM6301 R6303 C1003
C1018 C1049
C1048
C1010 R1132
R1101 KA004
CM6300
C6302 RB7022 RB7011 RB7018
CL1009 RB7025
CL7751 R7004
R7846
CL7750R7852R7849 R1051
R7847 R7848
R7853 C7008 R7015
C6011 C6023 C7824 C7831
CL7752 R7023
R6008 FB6003 C6009 C7823 R1098
CL5221 X7000
R7571
CL7753R7573
CM7703
R7960 RB7021 cam039
R6007 FB6002 C6008 R7811 R7962
R7570
R7575 ET034 RB7032 R7034
R7035R7033
C6010 C6022 C7819 cam072 R1123
C7832 C1438 R7019RB7012
C7821 R7813
C7871 R1027C1023 RB7007 R7002 R7032
CM7706 R1456 R8059 R7009
RB7713 RB7712 R7815 C1437 R1455 R1028 R7028 cam057
R8060
C7820 IC7707C7872
R7814 RB7005 C8427
R1010 R7025C1027
R7024 R8062 RB7016
R1467R1466
R7008 R7029
C7870 C1007 R7018 RB7014 RB7008
R8061 C7005
R7007 R7005 C8426
C5602 C7010 IC7003
R5613CM5202 R1009 C7009 R8423
R7973C7822 R6319
CL6305 C5603 R5351
R6321 R5612 RB7033RB7013 RB7031 C8422
R1124
C1005 cam076
R6320
CL6311 R7020 C8418 R7011 R7027
cam15 CL6308CL6307 RB7009
R6325R6322 CL6306 Q5605 R7026
R6015C6016
CM6004 R6070 R8419 R7010
RB7023 RB7028 C8425
R6016
CM6005
C6017 R6323 CL6309 IC8403 C7006
C6012 CL6310
R6071IC6000R6072 R6324 R5614R5615 RB7019 C7007
CM6006
R6017 CM6012 RB7020
R6018 R7030 C8421R8400
R8401 R7031
CM6007 R6009 C8417 C7002
R6020
CM6008
C6025 cam066
C6070 R6010
JC5227 R8402 cam074 cam056
R7006
R6021
CM6009
C6026 R6069 C7001
R6316R6317 CN7001 CN8400 A7001
CM6010 JC5235 JC5228 JC5243 C7004
R6022 RB7029 C7003
R6033
CM6011 JC5236 R5480 IC7002
JC5241 JC5244 R7003
IC8400 C8428
R6800 JC5242
C8430
R5506 R5504 RB7026 RB7035
R6801 R5501 R5499 C5356
C5377
C5353 C5376 C5298 X5202
C5361
R6802 CL5604 R5505 R5503 C8400
R5623
R5622 R5502 R5500 C5362
R6803 R5478
R5368
R5616 C5339 C5297 R8405
R6003 R5620 C5305 C5354 R8403
R8408
R8413 RB7030
C8420
C8424 C8407
R6004 R5621 C5307 C5306
C5336 C5342 C5340
C5308 C5309 C5330
C5337 C5341
C5375 C5374 C5352 C8423 RB7003 C8409
C5304 C5343 C5338 C5315
R5422
C5335 R8406
Q9018 R5617 R5400 C5326 cam031 R7014
A6000 C6007C6006 R5399 R8412 R8414
R5618 R7013
F9009 R7979 cam082 C5355 R8415
C6005
R6006C6004
R6005R6001
R6002 C7816 cam065 R7012 D8400
FB6001 R9190 C7813 R5619 Q5208 C5314 C5320 C8406 R8407 RB7034
C7808 R7809R7807 C8405 IC8401 RB7027
R9189 C5310 IC8402
C6002
C6001 C7818 C8403
C6021 CM7705 C7814R7808 R5421 R9014
C9002
C6020 C5311 RB5210 R8410 C8410
FB6006 C7806
C7807 C5378 RB7010 F8400
R5419 R9015 R9002 R8409 cam051 R7001 cam577
C9120 C7805 IC7703 RB7711RB7710 R5424 C9008 RB7017
R5423 C9012 R9003
R9008 C8402R8404R8420C8401
RB7708 C5317 RB5221 R8416
C6019 R9192
R9193 C5373 R9001 R8417R8418
C6018 R9019 RB5209 RB7015
R6062
R6063 FB6005 F6000 Q9019 C7812R7804 R9016
R9017 C5321 C8419 RB7024
C7817 cam078 COM700
R7805R7806 R5417
D5207 C5322
R6061 C7811 R5418RB5222 X8400
R7021
R6011 C7810 C7815 RB7709 C9003 C5360 IC9002
C6024 C6030 R6068 C7809 RB5223 R5431 C5327
CM6003 TP3104 C9043
C6029 R6014 R5430 C5325 C9034 C9037 R7016
CM6002R6065 D5208 R5397
R5398
C6028 R6013 D1402 R5433 C5332 RB5212 C9032
CM6001R6064 R1489 C1455 IC9000 C9040 cam14
cam022 R5432 C5303 R9207
C6027R6012
CM6000R6066
R1486 C9110 R9206 R9205
R9202
C9077 R1478 C1449 cam077 R5434 R5299 F9011 C9139 R9204
R1487 C5372 R9032 R8006
L9005 R6019R6067 C9053
R9058 R1485 IC1404 R5312 R9006 R5435 R5298 CL5228
RB5211 F9003 cam041
RB1400 CM5206
R5427
CL5269 CL5271 C5323 C9029 R9203 R8005
C8007
R6036 R5308
C5294 C9005 R5437 IC5212 C9142 D8000
C9071 Q6001 R9050
R9048 R9031 C8011
R8003C8010
C8014
C9055R9059
C9058
CL5301
R5436 R5481
CM5207
CL5272 C5324 C9141
CL8000
R9053 cam080 CL5273C5331 L9003
Q5203 R5438 R5391
CL5261 CL5262 C9137 C9136 C9135 IC9014 RB8003
C6013 C5359 R9033
C9066 C9063 C9111 C6800 TP3103 R1479 Q5204 R5439 C9140 C8008
C6014 CL5274 R5390
CL5259 CL5260 C9138
C1450 R5309 R5441CL5275
CL5276 R5477
C9079 cam090 IC1401 CL5277 C5381 C8006 IC8002
C6015 FB6800 R5440 C5333 C8012 X8000
CL5600 CL5263
CL5264 R5393 R8000
IC9006 R5442 R5444 R8023
C9083 FB6004 CL5601 CL5278 C5382 R5498 R8024 R8002
R9079 C9084 C9072 C9078 R5610 R5443 R5445CL5279 R5394 C9149 R8001
IC9005 TU6802 F9010 C5347 R5395 cam064
C9067 R5611 R5454 R5451
C8030 R5453 C9146 C9145 C9144 R8004C8009
C8013
R9078 C9080 R5408 R8068
cam067 R8032 R5455 Q5206
C8029 R5479 C5357 R5407 L9008 R8067 C8429
R8424
C9112 D1400 VD5600 CL5602 R5446
cam12 D5600 R5452 R5406
R9080 CL5603 R5447
R9049 R9052 C9064 C5606 R5405 R9123R9122R9121R9120
C9057 IC8006 IC8005 R5409 R8072
R9057 C9054 TU6003 L9006 CL5248Q5200 R5396
D5203 cam075
R9047 R8011R8008R8041
R8027
C6003 R5483
R5338R5341 R5482
R5340
R5339 D5204
C9052
R9056 R5491 R5347 C5334 RB5206 CM5203
R5373
R5508
C5246 R8049 C8411 C8414 C8413 C8412 C8408
R1470
R1471
R1480 R5487
R5490 cam088 C5200R5268R5374R5357
cam181 Q5209 R5207 R5208 R5473 R5507 R8048 R8007 R8040
R8026
C8028 C5296
C1454 cam2 CL5240 C5247 R8066
C1443 C1453 VD1400 C5295 D5200 R5484 R8047
C1444 R8031cam068 CL5299
CL5297 CL5226
CL5225 CL5255
CL5257
CL5253 C5348C5351 IC5208
R5474 C5363
CL5295
CL5293 CL5251
R5521 C5350
R5494
R5497
RB5205 R8050R8046IC8009 R8065 cam014
R5489 D5201 R5345 CL5300 R8054
C1445 IC1402 C7521 C7560
R7593
VD8008 R5475 C5319 C5365
C5364 C5328
C5366 C5318
C5367 CL5294CL5298
C5368 C5329 CL5256
CL5254
CL5258 C5349
CL5252 R5457 CL5239 R8064
D7512 R8033 JC8005 R5211
R5212D5202 CL5296 R5495 RB5224 IC5200 R8055
R7521R7558 R7592 C7562 C8039L8001 R5488 R5485 C5248
C5249 IC8010R8053R8036 R8063
C7559 L8002 R5353 R5274 CN5200 R5221
R5265
R5522
C1446 R1481 VD7520 R5209 R5472 R5320
R5297R5450
R5448
R5449 R5295RB5220
R5293
R5294 R5496 R8051 cam073 IC8007 C8031 JC8000
VD7538 C7561 VD8010
VD8011 VD8002
VD8003 VD8012
VD8013 RB5215 RB5214
R5273 cam042 R8071 R8035
VD8009 JC8001
FB7502 D7514 VD7539 TP3107 R5210 RB5213 R5296 C8038 C8040
R1475 D7513 D7537 C5222Q5201 cam081 R8037R8052 cam069 R8038 VD8001
VD8000
RB5216 CL5227 cam070 R8012 VD8005
VD8004
COM751 R8073 CM7707
R7818C7835 C7834 C7833 C8004
C8003 IC8000 R8009
VD8006 TP3100
D7538 CM5204
R5376
R5375
CM5205
R5377
R5378 R5380
R5379 D5206
D5205 C8032 C8002 IRM002 KA002
cam086 R1472
R1473 cam8 R7562 R5468
C5380 C8034 IC8008 cam903 R7845
VD7702 VD7701 VD7700 R8070
R8069 cam6
cam036 R5467 cam062 cam009
VD1401
VD1402 R7561 C5371 R5428 R5520
C5390 cam063
CM5200 RB5219 R5516
C5387 RB5218 cam377
RB5208 R5429 RB5207 R5524 R5515C5388
R5526 C5379 C5370 VD5203 IC8001
JC5240 JC5239 JC5238 JC5237 C5389 R5456JC5209 JC5208 R5509C5385 VD5205JC5217 JC5216
cam288 VD5210
VD5212 R5525
VD5208 VD5206
VD5207 R5518
R5517 R5519 VD5202
VD5204 VD5201
R5523
TU6001 VD5211 cam029 cam030 CL5237
VD5209 cam026 R5510 R8010
CL5238 cam902
CL5292 CL5270 CL5245
cam4 cam1 cam015
TU6000
cam007 TP3113
CN8000 CN8002
J7505 CN8005
J1401
J7700
CN5208 CN5203 CN5202 CN5201

cam010 cam002 cam003 cam004 cam001

cam006 cam005
cam004

cam001 cam002

KJ001 KJ002

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 163
 DIAGRAMS

BMFW (B SIDE)

KJ004 KJ003
cam007

cam008

CM7704

JL6029

JL8002
JL5208

JL6005

JL8007 JL8005JL8006 JL8008

JL6008
JL8024 IRM004 KB002
JL5209
ET006
JL6007 JL8003JL8004 JL5206 JL8011
JL8000 JL8009JL8010
JL5205
ET6000
ET6001 JL5204

JL5202
JL6009 JL5201 JL5203

C5383
JL6030
JL6010JL6011JL6028 JL6019 CL5283 C5384 JL5207
CL5282 DM002
CL5268
CL5284
CL5285
CL5286
CL5287
CL5288
CL5289
CL5290
CL5266
JL9021 CL5267

JL9022
JL6034

JL6014JL6016 JL6020JL6022 JL6025

KB004
JL6012JL6013 JL6802 JL6015JL6017 JL6021JL6023 JL6024JL6026 JL6032 CL5281
CL5280
ET015

JL6027 ET027

ET023

JL6006 JL6031 JL6018

ET019
JL6033

JL6004

ET029

ET025 CM7701

ET012

JL7816 JL9015

CL7764
CL6000 JL9016
CL8004
CL8005
CL7763
ET028
CL7600
CL7601
CL1000
CL1001
ET022 CL9800
CL9810

CL9801
JL7507 JL7506 CL9805CL9803
JL3103
JL3102
ET009
JL9024
JL3100JL3101

JL7500
CL8307CL8308 CL8301
ET014
JL3104JL3105
CL7708

JL9800
ET013

ET018
JL7830
cam008

JL8013
JL7831
JL8015 JL8014 JL9018 CL8711
ET007 CL8710
JL8012
JL7829

CL8709
CL8708

CL8707 CL8706

JL1015

JL1014

JL1013 JL1409 JL1408 ET024 ET011

JL1009 JL1405 JL1404 JL1403 JL1402 JL1401
JL9023 CL3109
JL1012
CL3604
JL1407 JL1406JL1410 JL1400
JL1011 JL3601
cam208
cam23
JL1010 JL1412 JL1411
cam209
ET030

cam16 cam17
cam092

cam210

cam093

cam094
cam006
JL9017

cam099

JL9025

ET026
JL9019 ET016
KB003
cam048
JL9026

ET017
JL9020

ET021

JL8016
KB001

JL8017
JL7824JL7823JL7822JL7821JL7820JL7819JL7818JL7817 JL7794 JL7790
JL1004
JL7795 JL7789
JL7801 JL7791
IRM003 JL1007
JL7800 JL1001
JL7813 JL7799 JL7815 JL1003JL1005
JL7802 JL7832
JL7814 JL9012 JL9013
JL1002 JL1008
JL7798 JL1000 JL1006
JL7788 JL9009JL9014
JL7804JL7803 JL9007JL9005JL9003JL9001
JL3600
JL9010

JL9011 JL9008JL9006JL9004JL9002JL9000

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 164
 DIAGRAMS

4-4. CIRCUIT BOARDS LOCATION

KD-49X8005C KD-55X8005C, XBR-55X805C/807C/809C/810C

SWITCH UNIT SWITCH UNIT

BMFW BMFW

GL6 SMART CORE

GL6 SMART CORE

XBR-65X800C/805C/807C/809C/810C

SMART CORE

BMFW
HSC3_L

SWITCH UNIT

WLAN/BT MODULE

GL6 SMART CORE

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 165
SEC 5. EXPLODED VIEWS
• Items with no part number and no description are not stocked because they are seldom required for routine service.
• The construction parts of an assembled part are indicated with a collation number in the remark column.
• Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

5-1. KD-49X8005C
REF. No. PART No. DESCRIPTION MARK
5-1-1. REAR COVER 1 A-2083-987-A COVER, REAR (M SWN) A
2 4-563-755-41 LABEL, SIDE TERMINAL (W)
3 4-563-765-01 LABEL, REAR TERMINAL
4 4-297-989-01 AC COVER
5 1-839-695-12 POWER-SUPPLY CORD (WITH CONN.)
6 1-754-955-11 BT ANTENNA
7 1-858-963-21 SPEAKER BOX ASSY (R)
8 1-858-963-11 SPEAKER BOX ASSY (L)

SMART CORE

7 3

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 166
 EXPLODED VIEWS

5-1-2. LCD PANEL REF. No. PART No. DESCRIPTION MARK

51 1-798-510-41 SWITCH UNIT (SM-G-KIT)
52 4-546-444-71 BRACKET, SIDE F (MOLD)
53 A-2084-761-A COMPLE SVC (XFLL) BMFW BRB
54 1-474-633-11 GL6(CH)-STATIC CONVERTER(TV)
55 4-565-059-11 SHEET, INSULATION(HRN L)
56 A-2083-989-A BRACKET, SP R (L SWN) A
57 A-2083-988-A BRACKET, SP L (L SWN) A
58 2-650-770-21 SLIDE, CLAMP
59 A-2087-489-A PACKING (M SWN_OS), SERVICE
51

59

52
53

58 57
55

54

56

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 167
 EXPLODED VIEWS

5-1-3. CONNECTORS

102 101

103

REF. No. PART No. DESCRIPTION MARK

101 1-849-080-11 FLEXIBLE FLAT CABLE 51P (XFC) CN3601(BMFW)-TCON (1)
102 1-910-110-70 CONNECTOR ASSY 28P CN6401(GL6)-CN9000(BMFW) (1)
103 1-910-110-71 HARNESS ASSY(MAIN) CN1000(BMFW)-CN101(HSC3)-WIFI-SM/CN7700(BMFW)-SP (1)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 168
 EXPLODED VIEWS

5-1-4. SCREWS

REF. DESCRIPTION PART No.

SCREW, +BVTP 4X12 TYPE2 IT-3 2-580-639-01

SCREW, +PSW M4X10 4-159-298-01
SCREW (+PSW) (M3X6) 2-990-421-41
SCREW , +PWH M3X6 4-452-935-11
SCREW, +PSW M3X6 W12 4-256-393-12
SCREW, +PSW M3X8 2-580-593-01

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 169
 EXPLODED VIEWS

5-2. KD-55X8005C, XBR-55X805C/807C/809C/810C

5-2-1. REAR COVER REF. No. PART No. DESCRIPTION MARK
201 4-569-944-02 COVER, REAR (L SWN) A CO1
201 4-569-944-12 COVER, REAR (L SWN) A CU2/ LA8/ ECU/
AR4
201 A-2083-986-A COVER, REAR (L SWN) A BR6
202 4-563-755-01 LABEL, SIDE TERMINAL (W) UC2
202 4-563-755-21 LABEL, SIDE TERMINAL (W) LA8/ CO1/ ECU/
AR4
202 4-563-755-41 LABEL, SIDE TERMINAL (W) BR6
203 4-563-764-01 LABEL, REAR TERMINAL EXCEPT BR6
203 4-563-765-01 LABEL, REAR TERMINAL LA8/ CO1/ ECU/
AR4/ BR6
204 4-297-989-01 AC COVER BR6
204 4-299-531-01 AC COVER EXCEPT BR6
205 1-839-692-12 POWER-SUPPLY CORD (WITH CONN.) AR4
205 1-839-695-12 POWER-SUPPLY CORD (WITH CONN.) LA8/ ECU/ BR6
205 1-839-696-13 POWER-SUPPLY CORD (WITH CONN.) UC2/ CO1
206 1-754-950-11 BT ANTENNA EXCEPT BR6
201 206 1-754-955-11 BT ANTENNA BR6
207 1-858-963-21 SPEAKER BOX ASSY (R)
208 1-858-963-11 SPEAKER BOX ASSY (L)
209 4-567-609-01 LABEL, CI CO1
208

SMART CORE 202

209

207
203

206

204
205

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 170
 EXPLODED VIEWS

5-2-2. LCD PANEL REF. No. PART No. DESCRIPTION MARK

251 1-798-510-31 SWITCH UNIT (SM-G-WW) EXCEPT BR6
251 1-798-510-41 SWITCH UNIT (SM-G-KIT) BR6
252 4-546-444-31 BRACKET, SIDE F (MOLD) UC2
252 4-546-444-61 BRACKET, SIDE F (MOLD) LA8/ CO1/ ECU/
AR4
252 4-546-444-71 BRACKET, SIDE F (MOLD) BR6
253 A-2072-554-C COMPLE SVC (XF) BMFW CO1 CO1
253 A-2072-555-C COMPLE SVC (XF) BMFW UC2 UC2
253 A-2084-108-A COMPLE SVC (XF) BMFW BRB LA8/ ECU/ AR4
251 253 A-2084-761-A COMPLE SVC (XFLL) BMFW BRB BR6
254 1-474-633-11 GL6(CH)-STATIC CONVERTER(TV)
259
255 4-565-059-11 SHEET, INSULATION(HRN L)
256 4-570-852-01 BRACKET, SP R (L SWN) A EXCEPT BR6
260 256 A-2083-989-A BRACKET, SP R (L SWN) A BR6
252
257 4-570-851-01 BRACKET, SP L (L SWN) A EXCEPT BR6
257 A-2083-988-A BRACKET, SP L (L SWN) A BR6
258 2-650-770-21 SLIDE, CLAMP
259 A-2087-488-A PACKING (L SWN_OS), SERVICE BR6
258 259 A-2087-487-A PACKING (2L SWN_OS), SERVICE EXCEPT BR6
260 4-546-441-11 BRACKET, TOP FL (MOLD) CO1
257

255 253

254

256

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 171
 EXPLODED VIEWS

5-2-3. CONNECTORS

303 302

304 301

REF. No. PART No. DESCRIPTION MARK

301 1-849-075-11 FLEXIBLE FLAT CABLE 51P CN3601(BMFW)-TCON (1)
302 1-849-076-11 FLEXIBLE FLAT CABLE 41P (EXCEPT BR6) CN3600(BMFW)-TCON (1)
303 1-910-110-67 CONNECTOR ASSY 28P (BR6) CN6401(GL6)-CN9000(BMFW) (1)
303 1-910-110-69 CONNECTOR ASSY 28P (EXCEPT BR6) CN6401(GL6)-CN9000(BMFW)-TCON (1)
304 1-910-110-68 HARNESS ASSY(MAIN) CN1000(BMFW)-CN101(HSC3)-WIFI-SM/CN7700(BMFW)-SP (1)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 172
 EXPLODED VIEWS

5-2-4. SCREWS

REF. DESCRIPTION PART No.

SCREW, +BVTP 4X12 TYPE2 IT-3 2-580-639-01

SCREW, +PSW M4X10 4-159-298-01
SCREW (+PSW) (M3X6) 2-990-421-41
SCREW , +PWH M3X6 4-452-935-11
SCREW, +PSW M3X6 W12 4-256-393-12
SCREW, +PSW M3X8 2-580-593-01

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 173
 EXPLODED VIEWS

5-3. XBR-65X800C/805C/807C/809C/810C
5-3-1. REAR COVER REF. No. PART No. DESCRIPTION MARK
401 4-569-942-02 COVER, REAR (2L SWN) A CO1
401 4-569-942-12 COVER, REAR (2L SWN) A UC2/ LA8/ LA1
402 4-563-755-01 LABEL, SIDE TERMINAL (W) UC2
402 4-563-755-11 LABEL, SIDE TERMINAL (W) LA1
402 4-563-755-21 LABEL, SIDE TERMINAL (W) LA8/ CO1
403 4-563-764-01 LABEL, REAR TERMINAL UC2
403 4-563-765-01 LABEL, REAR TERMINAL LA8/ CO1/ LA1
404 4-299-531-01 AC COVER
405 1-839-696-13 POWER-SUPPLY CORD (WITH CONN.) UC2/ LA1/ CO1
405 1-839-695-12 POWER-SUPPLY CORD (WITH CONN.) LA8
406 1-754-949-11 BT ANTENNA
407 1-858-963-21 SPEAKER BOX ASSY (R)
408 1-858-963-11 SPEAKER BOX ASSY (L)
409 4-567-609-01 LABEL, CI CO1

401

408 409

402
SMART CORE

407 403

406
404

405

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 174
 EXPLODED VIEWS

5-3-2. LCD PANEL REF. No. PART No. DESCRIPTION MARK

451 1-798-510-31 SWITCH UNIT (SM-G-WW)
452 4-546-444-11 BRACKET, SIDE F (MOLD) LA1
452 4-546-444-31 BRACKET, SIDE F (MOLD) CU2
452 4-546-444-61 BRACKET, SIDE F (MOLD) LA8/ CO1
453 A-2072-556-C COMPLE SVC (XF) BMFW LA1
454 4-570-849-01 BRACKET, SP (2L SWN) A
455 1-474-633-11 GL6(CH)-STATIC CONVERTER(TV)
456 4-565-059-11 SHEET, INSULATION(HRN L)
457 2-650-770-21 SLIDE, CLAMP
458 A-2087-483-A PACKING (L SWN_120), SERVICE
459 4-546-441-11 BRACKET, TOP FL (MOLD) CO1
458

459
452
451

457

453
454
457
456

455

454

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 175
 EXPLODED VIEWS

5-3-3. CONNECTORS

503 501

504 502

REF. No. PART No. DESCRIPTION MARK

501 1-849-078-11 FLEXIBLE FLAT CABLE 41P (XFF) CN3600(BMFW)-TCON (1)
502 1-849-079-11 FLEXIBLE FLAT CABLE 51P (XFF) CN3601(BMFW)-TCON (1)
503 1-910-110-65 CONNECTOR ASSY 28P CN6401(GL6)-CN9000(BMFW)-TCON (1)
504 1-910-110-66 HARNESS ASSY(MAIN) CN1000(BMFW)-CN101(HSC3)-WIFI-SM/CN7700(BMFW)-SP (1)

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 176
 EXPLODED VIEWS

5-3-4. SCREWS

REF. DESCRIPTION PART No.

SCREW, +BVTP 4X12 TYPE2 IT-3 2-580-639-01

SCREW, +PSW M4X10 4-159-298-01
SCREW (+PSW) (M3X6) 2-990-421-41
SCREW , +PWH M3X6 4-452-935-11
SCREW, +PSW M3X6 W12 4-256-393-12
SCREW, +PSW M3X8 2-580-593-01

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 177
 EXPLODED VIEWS

5-4. SMART CORE (LL, C)

REF. No. PART No. DESCRIPTION MARK
601 4-567-752-01 CASE, BOTTOM (LL)
602 A-2066-086-A HSC3_L MOUNT EXCEPT ECU
602 A-2088-030-A HSC3_L MOUNT KIT ECU
603 4-547-390-01 LIGHT, GUIDE BR6
603 4-564-313-01 LIGHT, GUIDE EXCEPT BR6
604 4-547-389-01 PANEL, ORNAMENT BR6
606
604 4-564-312-01 PANEL, ORNAMENT EXCEPT BR6
607 605 4-547-395-01 COVER, TOP BR6
605 4-564-317-01 COVER, TOP EXCEPT BR6
606 4-547-397-02 BRACKET, WIFI BR6
608
606 4-564-318-02 BRACKET, WIFI EXCEPT BR6
607 4-547-207-01 HEAT SINK(SC)
605 608 1-458-853-21 WLAN/BT MODULE(11AC)BRZ BR6
608 1-458-853-11 WLAN/BT MODULE(11AC) EXCEPT BR6

603

604 602

601

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 178
 EXPLODED VIEWS

5-5. OTHER PART

5-5-1. MISCELLANEOUS 5-5-2. ACCESSORIES

PART No. DESCRIPTION MARK PART No. DESCRIPTION MARK

3-876-036-71 UNI-LABEL, BLANK EXCEPT BR6 1-492-975-21 REMOTE COMMANDER (RMT-TX100B) LA8/ CO1/ ECU/ AR4
4-262-708-04 CLAMPER, CABLE 1-492-975-31 REMOTE COMMANDER (RMT-TX100B) BR6
4-534-964-01 PULLEY, STAND (HWI) 65" 1-492-978-21 REMOTE COMMANDER (RMT-TX100U) UC2
4-535-586-01 BADGE, XBR LOGO(H3.7) EXCEPT BR6 * 1-848-803-11 RCA CONVERSION CABLE EXCEPT UC2/ BR6
4-549-186-01 SHEET, THERMAL(BM) Refer P34/65/92 4-546-910-01 STAND NECK ASSY 65"
4-549-528-11 SHEET, THERMAL (SC) 4-564-539-01 STAND NECK ASSY (LAK) 55" (EXCEPT BR6)
7-600-031-97 TAPE (3M 1350FB-1)15MMX66M BLK 4-569-957-01 STAND, SHAFT (L SWN) A 55" (EXCEPT BR6)
A-2083-990-A STAND, SHAFT (L SWN) A 55" (BR6)
* 4-547-493-01 HEAT, SINK (MUFF) 4-569-963-01 STAND, SHAFT (2L SWN) A 65"
* 4-548-743-01 HOLDER, HS WS (MUF)
* 4-549-188-01 HOLDER(HS MUF) 4-570-853-01 BAG, SCREW (2L SWN) 65"
* 4-547-493-01 HEAT, SINK (MUFF) EXCEPT BR6 (2-580-607-01) (SCREW, +PSW M5X12)
* 4-563-516-01 HEAT SINK(MUFF CP) BR6 (SCREW, +PSW M5X20)
* 7-600-040-44 ADHESIVE (SV380C) 333CC GRY
4-570-854-01 BAG, SCREW (L SWN) 55" (EXCEPT BR6)
(2-580-607-01) (SCREW, +PSW M5X12)

2-580-607-01 SCREW, +PSW M5X12 49"/55" (BR6)

* 4-576-185-11 REFERENCE GUIDE UC2

* 4-576-187-11 REFERENCE GUIDE LA8/ CO1
* 4-576-188-11 REFERENCE GUIDE ECU
* 4-576-189-11 REFERENCE GUIDE AR4
* 4-579-449-11 REFERENCE GUIDE BR6
* 4-579-768-31 REFERENCE GUIDE LA1

7-600-031-96 TAPE (3M 1350FW-1)15MMX66M WHT EXCEPT BR6

1-785-504-21 ADAPTOR, CONVERSION LA8/ CO1

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 179
END

English
2015GL08-Data
Made in Japan
9-888-581-01 Sony Visual Products Inc. © 2015. 7
KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 180
APPENDIX-1
How to USB update

1:Download USB image and unzip file.

2: copy unzip file to USB memory root folder.

3: USB memory insert TV.

4:USB image is newer soft version. 4:USB image is not newer soft version.
Automatically show message and start update. Automatically show message and start update.
Please follow directions. Please follow directions.

Copying update file from USB. Please wait...

Preparing for system software update. During the No newer version of the system software was found.
system software update, the TV will automatically Please remove the USB device and select “OK” to exit.
restart. Please do not remove the USB device until an
update complete message is displayed. The update may
take up to 30 minutes to complete.

5: finished

The system software update is complete.

Some user settings may have changed during the update.
Please remove the USB device and select "OK" to exit.

5: finished

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 181
 APPENDIX-1

Software update for B board replacement

B board replacement Check the leftmost bit

of NVM version by “0”
Service mode to
confirm RCD version.
Is it except 0 or 0?
After AC Plug-in, wait for <Case1>
Panel : No Picture Except “0” Check the software
30sec then turn on TV by
SMART CORE LED : Red LED 3x blinking version by Service
power key on TV or remote
commander. mode.
Is it latest version?
No
Model Number setting
<Case3> Yes
Panel : Picture appear
SMART CORE LED : White Lit
Check condition.
Is it the Case 1,2 or 3?
Update to the latest
<Case2>
software version
*Remove all signal
Panel : No Picture
connection.
SMART CORE LED : Amber & Green blinking (antenna, external input,
or lit in white ether cable, etc)
Update to the latest *Insert the USB memory.
software version SMART CORE LED will
change to white blinking. Serial Number input and
*Remove all signal
connection. Check Model name by *After completes, TV will WB/Gamma, MURA, CUC
Different
(antenna, external input, Service mode. reboot by itself and turns on. data transfer by Service mode
ether cable, etc) Is it the same or *Disconnect the USB
*Insert the USB memory. memory.
different?
SMART CORE LED will
change to white blinking. *
Same
After completes, TV will Reconfirm Software version
reboot by itself and turns on.
*Disconnect the USB Note1:
and Model name by Service
memory. Check NVM version For a success of software writing, mode
affix by Service mode Different it will take 20~30 min/time.
to confirm the country.
Is it the same or
different? Note2:
Do not turn off TV while updating software. Turn off the TV by remote
In case of BRA&COL, TV will enter If older software package version is used, software
power key then reboot the set
STDBY status. Then press "Power" key of Same (AC OFF wait 10sec then AC
cannot be update.
plug-in), turn on the TV by
remote commander to turn on TV. TV will reboot and turn on again. remote power key.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 182
 APPENDIX-1

Software update for Panel/T-CON replacement

Check the software No

Panel/T-CON replacement version by Service
Model Number setting
mode.
Is it latest version?

Yes
Update to the latest
After AC Plug-in, wait for 30sec software version
then turn on TV by power key *Remove all signal
on TV or remote commander. connection.
(antenna, external input,
ether cable, etc)
Model Number setting *Insert the USB memory.
SMART CORE LED will
change to white blinking.
*After completes, TV will
Check condition
reboot by itself and turns on.
Is it the Case 1 or 2?
<Case2> *Disconnect the USB memory.
Panel : Picture appear
SMART CORE LED : White Lit

<Case1>
Panel : No Picture WB/Gamma, MURA, CUC data
SMART CORE LED : Amber & Green blinking transfer by Service mode
or lit in white

In case of BRA&COL, TV will enter STDBY

Update to the latest
status. Then press "Power" key of remote
software version
commander to turn on TV.
*Remove all signal
Reconfirm Software version
connection.
and Model name by Service
(antenna, external input, Note1:
For a success of software writing,
mode
ether cable, etc)
*Insert the USB memory. it will take 20~30 min/time.
SMART CORE LED will
Note2:
change to white blinking. Do not turn off TV while updating software.
*After completes, TV will Turn off the TV by remote
If older software package version is used, software power key then reboot the set
reboot by itself and turns on. cannot be update. (AC OFF wait 10sec then AC
*Disconnect the USB memory. TV will reboot and turn on again. plug-in), turn on the TV by
remote power key.

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 183
APPENDIX-2
Wire Dressing (KD-49X8005C)

VA Tape x8 Slide Clamp x1

・Fix wire • Hold wires

Harness Tie x6
• Fix wire

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 184
 APPENDIX-2

Wire Dressing (XBR-55X805C, 807C, 809C, 810C : 120Hz)

VA Tape x10 Slide Clamp x1

・Fix wire • Hold wires

Harness Tie x4
• Fix wire

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 185
 APPENDIX-2

Wire Dressing (KD-55X8005C : 60Hz)

Slide Clamp x1
VA Tape x9
• Hold wires
・Fix wire

Harness Tie x4
• Fix wire

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 186
 APPENDIX-2

Wire Dressing (XBR-65X800C, 805C, 807C, 809C, 810C)

VA Tape x10 Slide Clamp x3

・Fix wire • Hold wires

Harness Tie x2
• Fix wire

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 187
APPENDIX-3
Caution for Panel handling

Don’t grab plastic bezel only. Don’t push screen.

Risk of bezel broken. Risk of screen broken.

OK NG

KD-49/55X8005C,XBR-55/65X800C,805C,807C,809C,810C 188