DES C R IPTION Sure-Lites

The LED ALX7RGSAL series is UL924 code compliant solution for indoor Catalog # Type
exit requirements. It is available self-powered with a maintenance free
nickel cadmium battery. The self-powered version will operate for a
Project
minimum of 90 minutes during a power outage. This exit is field
configurable for red or green letters and for single or double face. It is
Comments Date
can be universally mounted (ceiling, wall, or end). The polycarbonate
housing is available in white.
Prepared by

SP EC IFIC A TION FEA T U R E S

E le c t r i c a l located inside the exit housing Cod e Co mplian ce

- Dual Voltage Input 120/277VAC, - Snap-out or snap-in chevron - UL 924 Listed
60Hz directional indicators have full - UL Damp Location Listed
- Line-latching 3/4” stroke - Life Safety NFPA 101
- Solid-State Voltage Limited - Universal exits can be field - NEC/OSHA
Charger configured as single face or - Most State and Local Codes
- Solid-State Switching double face - California Energy Code
- Brownout Protection - Snap-fit canopy with captive compliant
- Low Voltage Disconnect mounting screws included with - NOM listed
- Overload/Short Circuit Protection all exits
- Test Switch / Power Indicator - Exit can be ceiling, wall, or end Lamp Data
Light mounted - AC LED: Long life LED lamps
- Universal J-box mounting pattern provide uniform diffused
H ou s i n g C o n s t r u cti on - Operating temperature range illumination
- All components are injection 10 °C to 40 °C - DC: LED DC lamps (Brighter in
molded, color stable, high impact emergency mode)
polycarbonate material Ba tte ry - NOM listed
- Textured finish available in white - Sealed nickel cadmium
- Components are of snap-fit - Maintenance free, long life Warranty
construction to facilitate under - Full recharge time: - Five-year warranty
5-minute installation 24 hrs (max.) - Seven-year prorated battery
- Reinforcing ribs throughout warranty
to provide maximum strength
- Molded-in wireways facilitate APX7RGSAL
internal wire routing and
connections
SERIES
- All components including
battery and electronics are

8 7 6 5 4 3 2 1

POLYCARBONATE EXIT
REVISIONS

REV. DESCRIPTION DATE CHANGE_NUMBER BY APPROVED

5-1/2"
140mm
4-3/32"
104mm
SELF POWERED
F

EMERGENCY
F
3/4"
19mm

LED LAMPS
EXIT LIGHTING
-20˚to
10˚ to 40˚C
50˚C
8-1/4" 7-1/2"
210mm 191mm operating SALIDA EXIT
E temperature E

range

11-23/32"
298mm
1-11/16"
43mm ENERGY
DATA
D D
4-3/32"
104mm
Maximum power
3/4" consumption
19mm
under all charge
conditions:

Sealed Nickel Energy Data

OR D ER ING INFOR M A T I O N AC Only LED
C 8-1/4" 7-1/2" C
Cadmium Battery
210mm 191mm
LED Exits - Red Exits - Red
SAMPLE NUMBER: APX7RGSAL Input Power: Input Power:
Series Battery Face Options Letter Colors Housing Color SALIDA Catalog numbers 120V = 1.31W 120V = 2.34W
277V = 1.68W 277V = 1.62W
APX 7 = nickel _ = Universal RG = field _ = White SAL = SALIDA APX7RGSAL Input Current Input Current
cadmium 11-23/32" configurable 1-11/16"

battery 298mm
for red or green
43mm
2-11/32"
(Max.): (Max.):
B B
16-9/16"
421mm
60mm
120V = 0.09A 120V = 0.14A
USE WITH MULTI-SHEET DRAWINGS
REV
277V = 0.09A 277V = 0.10A
SL014-LineArt

20 19 18
ELECTRONIC CAD DRAWING. DO
17 16 15 14 13 12
DIMENSIONS THAT AFFECT
11 10
DENOTES CRITICAL
9 8 7 6 5
DENOTES FIRST PIECE
4 3 2
DENOTES FIRST
PAGE
Power Factor: Power Factor:
NOT REVISE MANUALLY. S SAFE HANDLING OR C DIMENSIONS AND P AND IN-PROCESS F PIECE

120V = >0.12 120V = >0.14

DIMENSIONS ARE IN INCHES OPERATION GUAGE CHECK POINTS INSPECTION INSPECTION ONLY
DIMENSIONS IN [ ] ARE IN MM
TOLERANCE GENERAL SHEET
APPROVALS
277V = >0.07 277V = >0.06
METAL
.X 0.030 .XX 0.03 DATE
ENGLISH (IN) .XX 0.010 .XXX 0.015
.XXX
.X
0.005
0.75 0.75
DRWN:
.XX
METRIC (MM) .XX 0.25 .XXX 0.38

MUST CONFORM TO ROHS SPECIFICATION CL-ES-1025

.XXX 0.12
SHEET METAL PIERCED,
+0.000
ENGLISH (IN) - 0.005 CHKD:
EXTRUDED, NAIL PUNCH HOLE METRIC (MM) +0.00
- 0.13

ANGLES ALL 1.0

A THIRD ANGLE PROJECTION APPR: TITLE:
CONFIDENTIAL - The information contained in this document is the property of Cooper A
Industries, Inc. It is not for public disclosure. Possession of the information does not x.x
L MOD: E0438910 2/21/2018
convey any right to loan, sell, or disclose the information. Unauthorized reproduction or
x.x
use of the information is prohibited. This document is to be returned to Cooper
Industries Inc. upon completion of the purpose for which it was loaned or upon request. MATERIAL: FINISH: SIZE: DWG NO:
SL014-LineArt REV: TD505071EN
COPYRIGHT Cooper Industries Inc. This is an unpublished work. The disclosure of this
work is limited to select personnel. Further dissemination or disclosure to the public is C DEV/ZINT NO:
0 May 15, 2018 4:44 PM
PROHIBITED. This unpublished work is protected by Federal Copyright law and all
rights thereunder are reserved by Cooper Industries, Inc.
PART NUMBER DO NOT SCALE DRAWING SURFACE AREA: 977.31 IN2 SCALE: WT: 1.53 LB VOL: 39.18 IN3 SHEET 1 OF 2
8 7 6 5 4 3 2 1
 AP SALIDA EXIT SERIES

TEC H NIC A L D A TA

Lam p s L i ne - L a tch ed Lo w Vo ltage Discon n ect

The AP Series Exits use energy All Pro’s line-latched electronic circuitry makes When the battery’s terminal voltage falls, the
efficient, long life LED’s to provide uniform installation easy and economical. A labor low voltage circuitry disconnects the lighting
diffuse illumination of the exit face. The efficient AC activated load switch prevents load. The disconnect remains in effect until
low operating costs and zero maintenance the lamps from turning on during installation normal utility power is restored, preventing
requirement makes LED lamps the wisest choice to a non-energized AC circuit. Line-latching deep battery discharge.
for exit signs today. eliminates the need for a contractor’s return
to a job site to connect the batteries when the T est S witch /P ower In d ica t o r Lig h t
H o u sin g C o n s t r u c t i o n building’s main power is turned on. A test switch located on the bottom of the exit
Rugged, durable, injection molded permits the activation of the emergency circuit
thermoplastic materials are used throughout Sol i d- State Charg er for a complete operational systems check. The
the AP Series Exits. All structural Supplied with a 120/277 VAC, voltage regulated Power Indicator Light provides visual assurance
components are designed with reinforcing solid-state charger. Immediately upon that the AC power is on.
ribs to add additional rigidity and to maximize restoration of AC current after a power failure,
structural integrity. These materials are impact the charger provides a high charge rate. The Overlo ad and S ho rt Circuit
and scratch resistant, and they have been UV charge circuit reacts to the condition of the P ro tection
stabilized to resist discoloration due to age battery and regulates the charging process in The solid-state overload monitoring device in
and ultraviolet radiation. All components are order to maintain peak battery capacity and the DC circuit disconnects the lamp load from
designed to be of snap-fit construction - no maximize battery life. Solid-state construction the battery should excessive wattage demands
mechanical fasteners - to facilitate installation recharges the battery following a power failure be made and automatically resets when the
in under 5-minutes. Any components required in accordance with UL 924. overload or short circuit is removed. This
for installation (wirenuts, wire leads, universal overload current protective feature eliminates
metal J-box bracket, etc.) are all included with Brownou t Circuit the need for fuses or circuit breakers for the DC
each exit. The design of the AP Series The brownout circuit on All Pro’s exits monitors load.
Exits enables configuration as single face or the flow of AC current to the exit and activates
double face in the field. The AP Series Exits the emergency lighting system when a S ealed Nickel Cadmiu m B at t er y
can be wall, ceiling, or end mounted. Housing predetermined reduction of AC power occurs. All Pro Emergency sealed nickel cadmium
available in white. This dip in voltage will cause most ballasted batteries are maintenance-free with a life
fixtures to extinguish causing loss of normal expectancy of 10 years. The sealed rechargable
Len s lighting even though a total power failure has nickel cadmium battery offers high discharge
Lenses for the AP Series Exits are made from not occurred. rates and stable performance over a wide
durable impact resistant range of temperatures. The specially designed
thermoplastic. All exit faces are designed with Sol i d- State T ran sfer resealable vent automatically controls cell
full 3/4” stroke snap-out or snap-in chevron The AP Series Exits incorporates pressure, assuring safety and reliability.
directional indicators to insure maximum solid-state switching which eliminates corroded This battery is best suited for harsh ambient
visibility and compliance with the latest codes. and pitted contacts or mechanical failures temperatures because the electrolyte is not
associated with relays. The switching circuit active in the electrochemical process.
is designed to detect a loss of AC voltage and
automatically energizes the lamps using DC Warranty
power. Upon restoration of AC power, the DC All-Pro products are backed by a five-year
power will be disconnected and the charger will warranty.
automatically recharge the battery.

Eaton
1121 Highway 74 South
Peachtree City, GA 30269 Specifications and
P: 770-486-4800 dimensions subject to
www.eaton.com/lighting change without notice.