2012 Ford Focus SE

2012-13 TRANSMISSIONS Automatic Transmission - Vehicles With: 6-Speed Automatic Transmission - 6DCT250 -
Focus

Possible Sources

l Connectors damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals
l Clutch position sensor
l Clutch motor
l TCM

PINPOINT TEST A: P0805, P0806, P0809, P0900, P0901, P0902, P0903

A1 READ AND RECORD ALL DTCS

l Using the diagnostic scan tool, retrieve all Diagnostic Trouble Codes (DTCs).

Are Diagnostic Trouble Codes (DTCs) P0805, P0806, P0809, P0900, P0901, P0902 and/or P0903
present?

Yes: For Diagnostic Trouble Codes (DTCs) P0805, P0806 and/or P0809, GO to A2

For Diagnostic Trouble Codes (DTCs) P0900, P0901, P0902 and/or P0903, GO to A7

No: REFER to: Special Testing Procedures .

Clutch 1.

A2 CHECK HALL-EFFECT SUPPLY VOLTAGE

l Ignition OFF.

l Disconnect Clutch Motor C1633.

l Inspect the connector for damaged or pushed-out terminals, corrosion, loose wires and missing or
damaged seals.
l Ignition ON.

NOTE: Clutch motor Hall-effect supply voltage should measure 5.1 volts with
the ignition switch in the RUN position.

l Measure.

Click to display connectors

Positive Lead Measurement / Action Negative Lead

C1633-1 -

lunes, 26 de febrero de 2024 05:09:19

05:09:16 p. m. Page 1 © 2011 Mitchell Repair Information Company, LLC.
 2012 Ford Focus SE
2012-13 TRANSMISSIONS Automatic Transmission - Vehicles With: 6-Speed Automatic Transmission - 6DCT250 -
Focus

Is the voltage is greater than 5.2 volts?

Yes: GO to A5
No: GO to A3
A3 CHECK THE HALL-EFFECT SUPPLY VOLTAGE CIRCUIT FOR AN OPEN
l Disconnect TCM C1750B.

l Inspect the connector for damaged or pushed-out terminals, corrosion, loose wires and missing or
damaged seals.
l Measure.

Click to display connectors

Positive Lead Measurement / Action Negative Lead

C1633-1 ohms C1750B-58

Is the resistance less than 5 ohms?

Yes: GO to A4
No: REPAIR the circuit.
A4 CHECK THE HALL-EFFECT SUPPLY VOLTAGE CIRCUIT FOR A SHORT TO GROUND
l Measure.

Click to display connectors

Positive Lead Measurement / Action Negative Lead

C1633-1 ohms -

Is the resistance greater than 10, 000 ohms?

Yes: GO to A6
No: REPAIR the circuit.
A5 CHECK THE HALL-EFFECT SUPPLY VOLTAGE CIRCUIT FOR A SHORT TO POWER
l Ignition OFF.

l Disconnect TCM C1750B.

l Inspect the connector for damaged or pushed-out terminals, corrosion, loose wires and missing or
damaged seals.
l Ignition ON.

l Measure.

Click to display connectors

Positive Lead Measurement / Action Negative Lead

lunes, 26 de febrero de 2024 05:09:17 p. m. Page 2 © 2011 Mitchell Repair Information Company, LLC.
 2012 Ford Focus SE
2012-13 TRANSMISSIONS Automatic Transmission - Vehicles With: 6-Speed Automatic Transmission - 6DCT250 -
Focus

C1633-1 -

Is the voltage greater than 5.2 volts?

Yes: REPAIR the circuit.

No: REPLACE clutch motor 1 with clutch motor 2 and GO to A6
A6 RUN COMPONENT TEST
l Run the Component Test,

REFER to: Special Testing Procedures .

Clutch 1.

Are Diagnostic Trouble Codes (DTCs) P0805, P0806 and/or P0809 present?

Yes: INSTALL a new TCM.

REFER to: Transmission Control Module (TCM) .

PROGRAM the TCM with the latest calibration,

REFER to: Transmission Control Module (TCM) Adaptive Learning .

No: INSTALL a new clutch motor,

REFER to: Clutch Actuator Motor .

PERFORM the Clutch Adaptive Learn, REFER to: Transmission Control Module (TCM)
Adaptive Learning .

A7 CHECK THE CLUTCH MOTOR 3 PHASE CIRCUITS FOR AN OPEN

l Ignition OFF.

l Disconnect TCM C1750B.

l Disconnect Clutch Motor C1633.

l Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or
damaged seals.
l Measure.

Click to display connectors

lunes, 26 de febrero de 2024 05:09:17 p. m. Page 3 © 2011 Mitchell Repair Information Company, LLC.
 2012 Ford Focus SE
2012-13 TRANSMISSIONS Automatic Transmission - Vehicles With: 6-Speed Automatic Transmission - 6DCT250 -
Focus

Positive Lead Measurement / Action Negative Lead

C1633-5 ohms C1750B-57
C1633-6 ohms C1750B-6
C1633-7 ohms C1750B-4
C1633-8 ohms C1750B-5

Are the resistances less than 5 ohms on all circuits?

Yes: GO to A8
No: REPAIR the circuit.
A8 CHECK THE CLUTCH MOTOR 3 PHASE CIRCUITS FOR A SHORT TO GROUND
l Measure.

Click to display connectors

Positive Lead Measurement / Action Negative Lead

C1633-6 ohms -
C1633-7 ohms -
C1633-8 ohms -

Are the resistances greater than 10, 000 ohms?

Yes: REPLACE clutch motor 1 with clutch motor 2 and GO to A9

No: REPAIR the circuit.
A9 RUN COMPONENT TEST
l Run the Component Test,

REFER to: Special Testing Procedures .

Clutch 1.

Are Diagnostic Trouble Codes (DTCs) P0900, P0901, P0902 and/or P0903 present?

Yes: INSTALL a new TCM.

REFER to: Transmission Control Module (TCM) .

PROGRAM the TCM with the latest calibration,

REFER to: Transmission Control Module (TCM) Adaptive Learning .

No: INSTALL a new clutch motor,

REFER to: Clutch Actuator Motor .

lunes, 26 de febrero de 2024 05:09:17 p. m. Page 4 © 2011 Mitchell Repair Information Company, LLC.
 2012 Ford Focus SE
2012-13 TRANSMISSIONS Automatic Transmission - Vehicles With: 6-Speed Automatic Transmission - 6DCT250 -
Focus

PERFORM the Clutch Adaptive Learn, REFER to: Transmission Control Module (TCM)
Adaptive Learning .

lunes, 26 de febrero de 2024 05:09:17 p. m. Page 5 © 2011 Mitchell Repair Information Company, LLC.