E000004-0000 Fuser

E000227-001 Power Supply (12 V ) (24 V)

Code: E000-0001
Description:
The temperature of the fixing assembly is abnormally high.While startup control is under way, the reading of the main
thermistor is less than 30 degC continuously for 200 msec or more 1 sec after the start of power supply. While
startupcontrol is under way, the reading of the main thermistor is less than 70 deg C continuouslyfor 200 msec or more 2
sec after the start of power supply. While startup control is underway, the reading of the main thermistor is less than 120
deg C continuously for 200 msec6 sec after the start of power supply. The startup control does not end 30 sec after thestart
of power supply.

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the main thermistor. Replace the DC
controller PCB.

Code: E001-0000

Description:
The temperature of the fixing assembly is abnormally high.The reading of the main thermistor is 250 deg C or more
continuously for 200 msec.

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the main thermistor. Replace the DC
controller PCB.

Code: E001-0001

Description:
The temperature of the fixing assembly is abnormally high.The hardware circuit detects overheating of the main or sub
thermistor for 200 msec

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the DC controller PCB.

Code: E001-0002

Description:
The temperature of the fixing assembly is abnormally high.The reading of the sub thermistor is 295 deg C or more
continuously for 200 msec.

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the sub thermistor. Replace the DC controller
PCB.

Code: E002-0000

Description:
The rise in temperature of the fixing assembly is faulty.While startup control is under way, the reading of the main
thermistor is less than 115 degC continuously for 400 msec 1.3 sec after it has indicated 100 deg C. While startup controlis
under way, the reading of the main thermistor is less than 150 deg C continuously for400 msec 1.3 sec after it has indicated
140 deg C.

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the main thermistor. Replace the DC
controller PCB.

Code: E003-0000
Description:
The fixing temperature is too low after a standby state.While regular temperature control is under way, the reading of the
main thermistor is lessthan 140 deg C continuously for 400 msec or more

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the main thermistor. Replace the DC
controller PCB.

Code: E004-0000

Description:
Failure in main/sub thermistorWhen disconnection is detected with connector of the main/sub thermistor for 30
seccontinuously while DC controller is working.

Remedy:
Clear the error in Service Mode: COPIER > FUNCTION > CLEAR > ERR.Replace the main thermistor (film unit). Replace DC
controller PCB.

Code: E007-0000

Description:
The rotation of the fixing film is faulty.While the fixing motor is rotating, the marker signal is not detected for 6 sec with
thereading of the main thermistor indicating 100 deg C or more.

Remedy:
Reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.Replace the main thermistor. Replace the DC
controller PCB.

Code: E010-0001

Description:
The rotation of the main motor is faulty.Detection is executed every 100 msec after the start of motor rotation; however,
the drivedetection signal is absent for 2 sec.

Remedy:
Replace the main motor. Replace the DC controller PCB.

Code: E010-0002

Description:
The rotation of the main motor is faulty.During motor rotation, detection is executed every 100 msec; however, the drive
signal isabsent 5 times in sequence.

Remedy:
Replace the main motor. Replace the DC controller PCB.

Code: E014-0001

Description:
The rotation of the fixing motor is faulty.Detection is executed every 100 msec after the start of motor rotation; however,
the drivedetection signal is absent for 2 sec.

Remedy:
Replace the fixing motor. Replace the DC controller PCB.

Code: E014-0002

Description:
The rotation of the fixing motor is faulty.During motor rotation, detection is executed every 100 msec; however, the drive
signal isabsent 5 times in sequence.

Remedy:
Replace the fixing motor. Replace the DC controller PCB.

Code: E019-0000
Description:
The waste toner case is full, or the waste toner case full sensor is faulty.When the waste toner case is identified as being
full for 2000 prints continuously, an alertis issued; thereafter, the case is identified as being full continuously for 100 prints.
Remedy:
Replace the waste toner sensor. Replace the DC controller PCB.

Code: E020-0000

Description:
The path between the sub hopper and the developing assembly is cloggedwith tonerThe developing assembly toner sensor
detects the absence of toner, while the sub hoppertoner sensor detects the presence of toner. With the developing clutch
turned on, thehopper feedscrew motor is rotated for 1 sec intermittently 194 times; still, the developingassembly toner
sensor does not detect the presence of toner

Remedy:
Replace the developing assembly toner sensor. Replace the sub hopper tonersensor. Replace the DC control PCB

Code: E024-0000

Description:
The developing assembly connector is disconnected/Disconnection of Tonersensor.The connection detection signal is
absent continuously for 100 msec

Remedy:
Replace the developing assembly toner sensor. Connect the connector. Replacethe DC controller PCB.

Code: E024-0001

Description:
The developing assembly connector is disconnected/Disconnection of Tonersensor.Disconnection of the wire used for
detecting the connection of the toner level sensor isfound. When the disconnection of the wire used for detecting the
connection of the tonerlevel sensor has been detected for 7.5 min without interruption (12.5 min in the manual/envelop
cassette feeding). When the disconnection of the wire used for detecting theconnection of the toner level sensor has been
detected for 12.5 min without interruption.-iR 3225When the disconnection of the wire used for detecting the connection
of the toner levelsensor has been detected for 7.5 min without interruption (12.5 min in the manual/envelop cassette
feeding).-iR 3245/3235/3230When the disconnection of the wire used for detecting the connection of the toner
levelsensor has been detected for 12.5 min without interruption.

Remedy:
Correct the cable. Replace the sensor.

Code: E025-0000

Description:
The hopper motor or the bottle motor is faulty.The sub hopper toner sensor connection detection signal is absent for 100
msec 10 timesin sequence.

Remedy:
Replace the sub hopper toner sensor. Connect the connector. Replace thedetection PCB.
Code: E025-0001

Description:
The hopper motor or the bottle motor is faulty.While the hopper motor is rotating, the motor error lock signal is detected
continuously 4times every 56 msec. Or, while the bottle motor is rotating, the motor error lock signal isdetected 22 times in
sequence every 10 msec.

Remedy:
Replace the hopper motor. Replace the bottle motor. Replace the DC controllerPCB.

Code: E032-0001

Description:
The NE controller counter malfunctions. An open circuit is detected for the count pulse signal.

Remedy:
Turn off the main power, and check the cable for an open circuit; then, turn themain power back on.

Code: E064-0001

Description:
The voltage of the power supply is faulty (high-voltage error).The value read from the EEPORM is outside a specific range.

Remedy:
Turn off and then back on the main power. Replace the EEPROM.

Code: E064-0002

Description:
The voltage of the power supply is faulty (high-voltage error).While output is being generated, the AD value of the primary
DC voltage is 230 (DEC) ormore for 100 msec 2 times in sequence. (However, after output, it is not detected for 100msec.)

Remedy:
Replace the high-voltage power supply. Replace the DC controller PCB.

Code: E064-0003

Description:
The voltage of the power supply is faulty (high-voltage error).While output is being generated, the AD value of the
developing DC voltage is 224 (DEC)or more for 10 msec 2 times in sequence. (However, after output, it is not detected for
100msec.)

Remedy:
Replace the high-voltage power supply. Replace the DC controller PCB.

Code: E064-0004

Description:
The voltage of the power supply is faulty (high-voltage error).While output is being generated, the AD value of the transfer
output current is 205 (DEC)or more for 100 msec 2 times in sequence. (However, after output, it is not detected for100
msec.)

Remedy:
Replace the high-voltage power supply. Replace the controller PCB.

Code: E064-0005

Description:
The voltage of the power supply is faulty (high-voltage error).While output is being generated, the AD value of the transfer
output voltage is 0 (DEC) for100 msec 2 times in sequence. (However, after output, it is not detected for 100 msec.)

Remedy:
Replace the high-voltage power supply. Replace the DC controller PCB.
Code: E110-0001

Description:
The scanner motor is faulty.The scanner motor speed lock signal does not indicate a locked state a specific period oftime
after the scanner motor has been started.

Remedy:
Replace the laser unit. Replace the DC controller PCB. Check the wiring.

Code: E110-0002

Description:
The scanner motor is faulty.The speed lock signal indicates a deviation 10 times in sequence at intervals of 10 msecafter
the signal has indicated a locked state.

Remedy:
Replace the laser unit. Replace the DC controller PCB. Check the wiring.

Code: E110-0003
Description:
With the image clock switched over, the scanner motor speed lock signaldoes not indicate a locked state 6.5 sec after a
switchover is made from low to normalspeed or 8 sec after a switchover is made from normal to low speed.

Remedy:
Replace the laser unit. Replace the DC controller PCB. Check the wiring.

Code: E191-0000

Description:
There is an error in the communication with the high-voltage power supply.The data transmission/reception does not end
normally 500 msec after the most recenttransmission/reception of data ended normally.

Remedy:
Replace the high-voltage power supply. Replace the DC controller PCB.

Code: E197-0000
Description:
Error in communication of laser driver PCBCommunication error with IMG1L (communication data)

Remedy:
- Check routing (wiring) - Replace the laser unit - Replace DC controller PCBP

Code: E197-0001

Description:
Error in communication of laser driver PCBCommunication error with IMG1L. (Serial communication ENG)

Remedy:
- Check routing (wiring) - Replace the laser unit - Replace DC controller PCBP

Code: E197-0003

Description:
Error in communication of laser driver PCBDisconnection of laser harness

Remedy:
- Check routing (wiring) - Replace the laser unit - Replace DC controller PCB

Code: E202-0001

Description:
There is an error in the detection of the CCD home position.The attempt to detect the home position fails when the CCD is
moved forward.

Remedy:
Disconnect and then connect the harness connector. Replace the optical HPsensor, optical motor, and reader controller
PCB.

Code: E202-0002
Description:
There is an error in the detection of the CCD home position.The attempt to detect the home position fails when the CCD is
moved back.

Remedy:
Disconnect and then connect the harness connector. Replace the optical HPsensor, optical motor, and reader controller
PCB.

Code: E225
Description:
The light intensity of the CCD is faulty.

Remedy:
Disconnect and then connect the flexible cable. Replace the flexible cable, CCDunit, and reader controller PCB.

Code: E227-0001

Description:
The reader unit power supply (24V) is faulty. At time of power-on, the 24V port is off.

Remedy:
Disconnect and then connect the power supply harness connector. Replace thepower supply.

Code: E227-0002

Description:
The reader unit power supply (24V) is faulty. At the start of a job, the 24V port is off.

Remedy:
Disconnect and then connect the power supply harness connector. Replace thepower supply

Code: E227-0003

Description:
The reader unit power supply (24V) is faulty. At the end of a job, the 24V port is off.

Remedy:
Disconnect and then connect the power supply harness connector. Replace thepower supply.

Code: E227-0004

Description:
The reader unit power supply (24V) is faulty.When a load is being driven, the 24V port is off.

Remedy:
Disconnect and then connect the power supply harness connector. Replace thepower supply.

Code: E248-0001

Description:
EEPROM error An error has occurred at power-on.

Remedy:
Replace the reader controller PCB.

Code: E248-0002

Description:
EEPROM error An error has occurred during write operation.

Remedy:
Replace the reader controller PCB.

Code: E248-0003
Description:
EEPROM error An error has occurred during read operation following write operation.

Remedy:
Replace the reader controller PCB

Code: E261-0000
Description:
The zero-cross signal is faulty.When the relay is on, the zero-cross signal is not detected for 500 msec or more.

Remedy:
Replace the AC driver PCB. Replace the DC controller PCB.

Code: E280-0001

Description:
Reading unit communication errorReception status error

Remedy:
Disconnect and then connect the flexible cable. Replace the flexible cable

Code: E280-0002

Description:
Reading unit communication errorReception interrupt error

Remedy:
Disconnect and then connect the flexible cable. Replace the flexible cable

Code: E280-0003

Description:
Reading unit communication errorInsufficient insertion of the reading unit connector

Remedy:
Disconnect and then connect the flexible cable. Replace the flexible cable

Code: E315-0007

Description:
There is an error in image data.There is an error in JBIG encoding.

Remedy:
Turn off and then back on the power.

Code: E315-000d

Description:
There is an error in image data.There is an error in JBIG decoding.

Remedy:
Turn off and then back on the power.

Code: E315-000e

Description:
There is an error in image data.Error in decoding of software

Remedy:
Replace the main controller PCB

Code: E315-0025

Description:
There is an error in image data.Error in ROTU hardware

Remedy:
Replace SDRAM. Replace HDD. Replace the main controller PCB

Code: E315-0027
Description:
There is an error in image data.Error in ROTU timeout

Remedy:
Replace SDRAM. Replace HDD. Replace the main controller PCB.

Code: E315-0033

Description:
There is an error in image data.Error in MemFill hardware

Remedy:
Replace the main controller PCB.

Code: E315-0035

Description:
There is an error in image data.Error in MemFill timeout

Remedy:
Replace the main controller PCB.

Code: E315-0100

Description:
There is an error in image data.Error in PrcOverRun

Remedy:
Replace the main controller PCB.

Code: E315-0500

Description:
There is an error in image data.Error in device timeout [location to be detected] image process module (SCIO)
[Detectiontiming] when there is no interruption 2 min after the operation has been started

Remedy:
Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Code: E315-0501

Description:
There is an error in image data.Device: abnormal termination error [location to be detected] image process module(SCIO)
[Detection timing] When abnormal interruption is detected after the operation hasbeen started.

Remedy:
Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Code: E315-0510
Description:
There is an error in image data.Device: timeout error [Location to be detected] image process module (SCIP)
[Detectiontiming] when there is no interruption 2 min after the operation has been started.

Remedy:
Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Code: E315-0511

Description:
There is an error in image data.Device: abnormal termination error [Location to be detected] image process module(SCIP)
[Detection timing] when abnormal interruption is detected after the operation hasbeen detected

Remedy:
Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Code: E315-0520
Description:
There is an error in image data.Device: timeout error [Location to be detected] image process module (CMIP)
[Detectiontiming] When there is no interruption 2 min after the operation has been started

Remedy:
Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Code: E315-0521

Description:
There is an error in image data.Device: abnormal termination error [Location to be detected] image process module(CMIP)
[Detection timing] when abnormal interruption is detected after the operation hasbeen detected

Remedy:
Check connection with DDI-S cable(RCON). Replace the main controller PCB
Code: E315-0530

Description:
There is an error in image data.Device: timeout error [Location to be detected] image process module (JPEN)
[Detectiontiming] when there is no interruption 2 min after the operation has been started.

Remedy:
Turn OFF and then ON the power. Replace the main controller PCB if thisoccurs frequently.

Code: E315-0531

Description:
There is an error in image data.Device: abnormal termination error [Location to be detected] image process module(JPEN)
[Detection timing] when abnormal interruption is detected after the operation hasbeen started.

Remedy:
Turn OFF and then ON the power. Replace the main controller PCB if thisoccurs frequently.

Code: E315-0540

Description:
There is an error in image data.Device: timeout error [Location to be detected] image process module (JPDE)
[Detectiontiming] when there is no interruption 2 min after the operation has been started.

Remedy:
Turn OFF and then ON the power. Replace the main controller PCB if thisoccurs frequently.

Code: E315-0541

Description:
There is an error in image data.Device: abnormal termination error [Location to be detected] image process module(JPDE)
[Detection timing] when abnormal interruption is detected after the operation hasbeen started

Remedy:
Turn OFF and then ON the power. Replace the main controller PCB if thisoccurs frequently.

Code: E315-0550

Description:
There is an error in image data.Device: timeout error [Location to be detected] image process module (PRIP)
[Detectiontiming] when there is no interruption 2 min after the operation has been started.
Remedy:
Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Code: E315-0551
Description:
There is an error in image data.Device: abnormal termination error [Location to be detected] image process module(PRIP)
[Detection timing] when abnormal interruption is detected after the operation hasbeen started.

Remedy:
Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Code: E315-0560

Description:
There is an error in image data.Device: timeout error [Location to be detected] image process module (PRIO)
[Detectiontiming] when there is no interruption 2 min after the operation has been started.

Remedy:
Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Code: E315-0561

Description:
There is an error in image data.Device: abnormal termination error [Location to be detected] image process module(PRIO)
[Detection timing] when abnormal interruption is detected after the operation hasbeen started.

Remedy:
Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Code: E400-0001

Description:
Fault in communication with the ADF driver PCBThe checksum values of data from the ADF driver PCB are inconsistent 14
timesconsecutively.

Remedy:
Check connection of ADF lattice cable (cleaning of connecting point). Replace ADF driver PCB. Replace the reader controller
PCB.

Code: E400-0002

Description:
The statuses of data from the ADF driver PCB are inconsistent 14 timesconsecutively.

Remedy:
Check connection of ADF lattice cable (cleaning of connecting point). Replace ADF driver PCB. Replace the reader controller
PCB.

Code: E400-0003

Description:
SCI serial communication error interrupt is detected 14 times consecutively.

Remedy:
Check connection of ADF lattice cable (cleaning of connecting point). Replace ADF driver PCB. Replace the reader controller
PCB.

Code: E413-0001

Description:
The level of the pressure HP sensor does not change in a specified period oftime.When the pressure motor is activated, the
level of the pressure HP sensor does notchange in a specified period of time with the lead roller opened.

Remedy:
Replace the pressure motor. Replace the pressure HP sensor
Code: E413-0002
Description:
The level of the pressure HP sensor does not change in a specified period oftime.When the pressure motor is activated, the
level of the pressure HP sensor does notchange in a specified period of time with the lead roller closed.

Remedy:
Replace the pressure motor. Replace the pressure HP sensor.

Code: E490-0001

Description:
The ADF installed is not supported.Error with an incorrect ADF model

Remedy:
The ADF installed is not supported. Replace the DC controller PCB.

Code: E500-0001

Description:
fault in communication with the finisher (common among all finishers)

Remedy:
Replace the finisher controller PCB. Replace the DC controller PCB.

Code: E503-0002

Description:
fault in communicationfault in communication between finisher and saddle unit

Remedy:
Replace the finisher controller PCB. Replace the saddle controller PCB. Checkthe cable.

Code: E503-0003

Description:
with the finisher (External finisher)fault in communication between finisher and punch unit

Remedy:
Replace the finisher controller PCB. Replace the punch drive PCB. Check thecable.

Code: E505-0001

Description:
fault in the backup memory of the finisher (common among all finishers)fault in the data stored in backup memory

Remedy:
Turn off the main power. Check the wiring of the DC controller PCB and thefinisher controller, and check the fuse of the 24-
V power supply. Thereafter, turn the mainpower back on.

Code: E505-0002

Description:
fault in the EEPROM data of the punch unit

Remedy:
Replace the punch driver PCB. Replace the finisher controller PCB.

Code: E514-0001

Description:
fault in stack delivery motor (Finisher-S1)When the stack retaining spacer is returned to home position, the belt escape
homeposition sensor does not go on within 1.5 sec.
Remedy:
Replace the finisher controller PCB. Replace the stack delivery motor. Check thestack delivery drive mechanism.
Code: E514-0001

Description:
fault in trailing edge assist motor (External finisher)The home position sensor does not go off even when the trailing edge
assist motor hasrotated for a specific period of time.

Remedy:
Replace the finisher control PCB. Replace the trailing edge assist motor

Code: E514-0002

Description:
fault in stack delivery motor (Finisher-S1)When the stack retaining spacer is shifted from home position, the belt escape
homeposition sensor does not go off within 1.5 sec.

Remedy:
Replace the finisher controller PCB. Replace the stack delivery motor. Check thestack delivery drive mechanism.

Code: E514-0002

Description:
fault in trailing edge assist motor (External finisher)The home position sensor does not go on even after the trailing edge
assist motor hasrotated for a specific period of time.

Remedy:
Replace the finisher control PCB. Replace the trailing edge assist motor

Code: E519-0001

Description:
Gear change motor error (External finisher)The home position sensor does not go off even when the gear change motor
has rotatedfor a specific period of time.

Remedy:
Replace the finisher controller PCB. Replace the gear change motor. Check thegear change mechanism.

Code: E519-0002

Description:
Gear change motor error (External finisher)The home position sensor does not go on even when the gear change motor
has rotatedfor a specific period of time.

Remedy:
Replace the finisher controller PCB. Replace the gear change motor. Check thegear change mechanism.

Code: E520-0001

Description:
The offset motor or the finisher controller PCB is faulty. The offset homeposition sensor is faulty (Finisher-S1).While the
offset motor is in operation, drive was applied for 1000 msec for movementtoward the home position sensor; however, the
offset home position sensor does not goon.

Remedy:
Replace the offset motor. Replace the offset home position sensor. Replace thefinisher controller PCB.

Code: E520-0002

Description:
The offset motor or the finisher controller PCB is faulty. The offset homeposition sensor is faulty (Finisher-S1).While the
offset motor is in operation, drive was applied for 1000 msec for movement away from the home position sensor;
however, the offset home position sensor does notgo off.
Remedy:
Replace the offset motor. Replace the offset home position sensor. Replace thefinisher controller PCB.

Code: E530-0001

Description:
Front alignment error (External finisher)The home position sensor does not go off even when the front alignment motor
has beenrotated for a specific period of time.

Remedy:
Replace the finisher controller PCB. Replace the front alignment motor. Checkthe front aligning plate drive mechanism.
Check the front alignment home position sensor.

Code: E530-0002

Description:
Front alignment error (External finisher)The home position sensor does not go on even when the front alignment motor
has beenrotated for a specific period of time.

Remedy:
Replace the finisher controller PCB. Replace the front alignment motor. Checkthe front aligning plate drive mechanism.
Check the front alignment home position sensor.

Code: E530-8001

Description:
Rear alignment error (Finisher-S1)The home position sensor does not go on within 2000 msec after the start of
operationwhen the rear aligning plate is shifted to home position.

Remedy:
Replace the finisher controlled PCB. Replace the rear alignment motor. Checkthe rear aligning plate drive mechanism.
Check the rear alignment home position sensor.

Code: E530-8002

Description:
Rear alignment error (Finisher-S1)The home position sensor does not go off within 1000 msec after the start of
operationwhen the rear aligning plate is shifted from home position.

Remedy:
Replace the finisher controlled PCB. Replace the rear alignment motor. Checkthe rear aligning plate drive mechanism.
Check the rear alignment home position sensor.

Code: E531-0001

Description:
Stapler error (External finisher)The home position sensor does not go off even when the stapler motor has rotated for
aspecific period of time.

Remedy:
Replace the finisher controller PCB. Replace the stapler. Check the harness.

Code: E531-0002

Description:
Stapler error (External finisher)The home position sensor does not go on even when the stapler motor has rotated for
aspecific period of time.

Remedy:
Replace the finisher controller PCB. Replace the stapler. Check the harness.

Code: E531-8001
Description:
Stapler error (Finisher-S1) At time of staple jam recovery, the home position sensor does not go on with 500 msecafter the
start of reverse rotation of the stapler motor.

Remedy:
Replace the finisher controller PCB. Replace the stapler. Check the harness.

Code: E531-8002

Description:
Stapler error (Finisher-S1)The home position sensor does not go off within 500 msec after the stapler motor hasbeen
started.

Remedy:
Replace the finisher controller PCB. Replace the stapler. Check the harness.

Code: E532-0001

Description:
Stapler shift error (External finisher)The home position sensor does not go off even after the stapler shift motor has rotated
fora specific period of time.

Remedy:
Replace the finisher controller PCB. Replace the swing cam motor. Check theswing cam home position sensor. Check the
harness.

Code: E532-0002

Description:
Stapler shift error (External finisher)The home position sensor does not go on even when the stapler shift motor has
rotatedfor a specific period of time.

Remedy:
Replace the finisher controller PCB. Replace the swing cam motor. Check theswing cam home position sensor. Check the
harness.

Code: E532-8001

Description:
Stapler shift error (Finisher-S1)The stapler slide home position sensor does not go on within 11 sec when the stapler
isshifted to home position.

Remedy:
Replace the finisher controller PCB. Replace the stapler shift motor. Check thestapler shift home position sensor. Check the
harness.

Code: E532-8002

Description:
Stapler shift error (Finisher-S1)The stapler slide home position sensor does not go off within 1.0 sec when the stapler
isshifted from home position.

Remedy:
Replace the finisher controller PCB. Replace the stapler shift motor. Check thestapler shift home position sensor. Check the
harness.

Code: E535-0001

Description:
Swing cam error (Finisher-S1)The home position sensor does not go off within 1000 msec after the start of operationwhen
the swing arm is shifted from home position.

Remedy:
Replace the finisher controller PCB. Replace the swing cam motor. Check theswing cam home position sensor. Check the
harness
Code: E535-0001

Description:
Swing cam error (External finisher)The home position sensor does not go off even when the swing motor has rotated for
aspecific period of time.

Remedy:
Replace the finisher controller PCB. Replace the swing cam motor. Check theswing cam home position sensor. Check the
harness.

Code: E535-0002

Description:
Swing cam error (Finisher-S1)The home position sensor does not go off within 1.0 sec when the stack delivery rollerswing
arm is moved from home position.

Remedy:
Replace the finisher controller PCB. Replace the swing cam motor. Check theswing cam home position sensor. Check the
harness

Code: E535-0002

Description:
Swing cam error (External finisher)The home position sensor does not go on even when the swing motor has rotated for
aspecific period of time.

Remedy:
Replace the finisher controller PCB. Replace the swing cam motor. Check theswing cam home position sensor. Check the
harness.

Code: E537-0001

Description:
Rear alignment error (External finisher)The home position sensor does not go on within 2000 msec after the start of
operationwhen the read aligning plate is moved to home position.

Remedy:
Replace the finisher controller PCB. Replace the rear alignment motor. Checkthe rear aligning plate drive mechanism.
Check the rear alignment home position sensor

Code: E537-0002

Description:
Rear alignment error (External finisher)The home position sensor does not go off within 1000 msec after the start of
operationwhen the rear aligning plate is moved form home position.

Remedy:
Replace the finisher controller PCB. Replace the rear alignment motor. Checkthe rear aligning plate drive mechanism.
Check the rear alignment home position sensor

Code: E537-8001

Description:
Front alignment error (Finisher-S1)The home position sensor does not go on within 2.0 sec when the front aligning plate
ismoved to home position.

Remedy:
Replace the finisher controller PCB. Replace the front alignment motor. Checkthe front aligning plate drive mechanism.
Check the front alignment home position sensor.

Code: E537-8002
Description:
Front alignment error (Finisher-S1)The home position sensor dos not go off within 1.0 sec when the front aligning plate
isshifted from home position.
Remedy:
Replace the finisher controller PCB. Replace the front alignment motor. Checkthe front aligning plate drive mechanism.
Check the front alignment home position sensor.

Code: E540-0002

Description:
Upper tray ascent/descent motor error (External finisher)Upper tray ascent/descent motor clock error

Remedy:
Replace the No. 1 tray shift motor. Replace the finisher controller PCB. Checkthe tray ascent/descent mechanism.

Code: E540-0003

Description:
Area error

Remedy:
Replace the No. 1 tray area sensor PCB. Replace the finisher controller PCB.

Code: E540-0004

Description:
Safety switch activation

Remedy:
Check the No. 1 tray closed detecting switch. Replace the finisher controllerPCB.

Code: E540-8002

Description:
Stack tray motor error (FinisherS1)The operation to detect the paper surface of the stack tray does not end within 1.0 sec.

Remedy:
Replace the finisher controller PCB. Replace the tray ascent/descent motor.Check the stack tray drive mechanism. Check
the paper surface sensor.

Code: E540-8003

Description:
Stack tray motor error (FinisherS1) An abnormal combination of sensor states has been detected.

Remedy:
Replace the finisher controller PCB. Check the stack tray upper limit sensor.Check the stack tray lower limit sensor. Check
the stack tray upper paper surface sensor.Check the stack tray lower paper surface sensor.

Code: E542-0002

Description:
Lower tray ascent/descent motor error (External finisher)Lower tray ascent/descent motor clock error

Remedy:
Replace the No. 2 tray shift motor. Replace the finisher controller PCB. Checkthe tray ascent/descent mechanism

Code: E542-0003

Description:
Lower tray ascent/descent motor error (External finisher) Area error
Remedy:
Replace the No. 2 tray shift area sensor PCB. Replace the finisher controllerPCB.

Code: E577-8001
escription:
Paddle error (Finisher-S1)The paddle home position sensor does not go on within 1.5 sec when the paddle is shiftedto
home position.

Remedy:
Check the paddle motor. Check the paddle home position sensor. Replace thefinisher controller PCB

Code: E577-8002

Description:
The paddle home position sensor does not go off within 1.0 sec when thepaddle is moved to home position.

Remedy:
Check the paddle motor. Check the paddle home position sensor. Replace thefinisher controller PCB

Code: E584-0001

Description:
Shutter unit error (External finisher)The shutter open sensor does not go off (i.e., the shutter does not close).

Remedy:
Check the stack edging motor. Check the open/close clutch. Check the shutterhome position sensor. Replace the finisher
controller PCB.

Code: E584-0002

Description:
Shutter unit error (External finisher)The shutter open sensor does not go on (i.e., the shutter does not open).

Remedy:
Check the stack edging motor. Check the open/close clutch. Check the shutterhome position sensor. Replace the finisher
controller PCB.

Code: E590-0001

Description:
Punch motor errorThe punching home position is not detected even when the puncher motor has beendriven for 20 msec.

Remedy:
Check the punch motor. Check the punch motor clock sensor. Check the punchdriver PCB. Replace the finisher controller
PCB.

Code: E590-0002

Description:
Punch motor errorThe punch home position sensor is not defected even after the motor has stopped at timeof punch
motor initial operation.

Remedy:
Check the punch motor. Check the punch motor clock sensor. Check the punchdriver PCB. Replace the finisher controller
PCB.

Code: E591-0001

Description:
Punch dust sensor errorError in light-receiving voltage while light is emitted

Remedy:
Check the waste paper case full sensor. Check the punch driver PCB. Replacethe finisher controller PCB.
Code: E591-0002
Description:
Punch dust sensor errorError in light-receiving voltage while light is not emitted

Remedy:
Check the waste paper case full sensor. Check the punch driver PCB. Replacethe finisher controller PCB.

Code: E592-0001

Description:
Paper trailing edge sensor/ horizontal sensor errorError in light-receiving voltage when light is emitted (trailing edge
sensor)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller PCB.

Code: E592-0002

Description:
paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is not emitted (trailing edge
sensor)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch drive PCB. Replace the
finisher controller PCB.

Code: E592-0003

Description:
paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is emitted (horizontal
registration sensor 1)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller PCB.

Code: E592-0004

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is not emitted (horizontal
registration sensor 1)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller PCB.

Code: E592-0005

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is emitted (horizontal
registration sensor 2)

Remedy:
Check the paper training edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller PCB.

Code: E592-0006

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is not emitted (horizontal
registration sensor 2)
Remedy:
Check the paper training edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller.

Code: E592-0007

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is emitted (horizontal
registration sensor 3)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller PCB
Code: E592-0008

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is not emitted (horizontal
registration sensor 3)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch drive PCB. Replace the
finisher controller PCB.

Code: E592-0009

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is not emitted (horizontal
registration sensor 4)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch driver PCB. Replace the
finisher controller PCB.

Code: E592-000A

Description:
Paper trailing edge sensor/ registration sensor errorError in light-receiving voltage when light is not emitted (horizontal
registration sensor 4)

Remedy:
Check the paper trailing edge sensor. Check the horizontal registration sensor.Check the punch drive PCB. Replace the
finisher controller PCB.

Code: E593-0001

Description:
Punch shift motor errorThe light-receiving voltage home position sensor does not go off when light is emitted.

Remedy:
Check the horizontal registration motor. Check the horizontal registration homeposition sensor. Check the punch driver
PCB. Replace the finisher controller PCB. Checkthe punch shift mechanism.

Code: E593-0002

Description:
Punch shift motor errorThe light-receiving voltage home position sensor does not go on when light is not emitted.

Remedy:
Check the horizontal registration motor. Check the horizontal registration homeposition sensor. Check the punch driver
PCB. Replace the finisher controller PCB. Checkthe punch shift mechanism.

Code: E5F0-0001
Description:
Saddle paper positioning plate errorThe paper positioning plate home position sensor does to go on when the
paperpositioning motor has been driven for 1.33 sec. Paper positioning plate motor (M4S)/paperpositioning plate home
position sensor (P17S)

Remedy:
Check the paper positioning plate motor. Check the paper positioning platehome position sensor. Replace the finisher
controller PCB. Check the paper positioningplate drive mechanism

Code: E5F0-0002

Description:
Saddle paper positioning plate errorThe paper positioning plate home position sensor doest not go off when the
paperpositioning plate motor has been driven for 1 sec. Paper positioning plate motor(M4S)/paper positioning plate home
position sensor (P17S)
Remedy:
Check the paper positioning plate motor. Check the paper positioning platehome position sensor. Replace the finisher
controller PCB. Check the paper positioningplate drive mechanism

Code: E5F1-0001

Description:
Saddle paper folding errorThe number of detection pulses of the paper folding motor clock sensor has droppedbelow a
specific value. Paper folding motor (M2S)/paper folding motor clock sensor(P14S)

Remedy:
Check the paper folding motor. Check the paper folding motor clock sensor.Replace the finisher controller PCB. Check the
paper folding plate drive mechanism.

Code: E5F1-0002

Description:
Saddle paper folding errorThe state of the paper folding home position sensor doest not change when the paperfolding
motor has been driven for 3 sec. Paper folding motor (M2S)/paper folding motorclock sensor (P14S)

Remedy:
Check the paper folding motor. Check the paper folding motor clock sensor.Replace the finisher controller PCB. Check the
paper folding plate drive mechanism.

Code: E5F2-0001

Description:
Saddle guide errorThe guide home position sensor does not go on when the guide motor has been driven for0.455 sec.
Guide motor (M3S)/guide home position sensor (PI13S)

Remedy:
Check the guide motor. Check the guide home position sensor. Replace thefinisher controller PCB. Check the guide drive
mechanism.

Code: E5F2-0002

Description:
Saddle guide errorThe guide home position sensor does not go off when the guide motor has been driven for1 sec. Guide
motor (M3S)/guide home position sensor (PI13S)

Remedy:
Check the guide motor. Check the guide home position sensor. Replace thefinisher controller PCB. Check the guide drive
mechanism.

Code: E5F3-0001

Description:
Saddle alignment errorThe aligning plate home position sensor does not go on when the alignment motor hasbeen driven
for 0.5 sec. (at time of initialization, 1.67 sec.) Alignment motor (M5S)/aligningplate home position sensor (PI5S)

Remedy:
Check the alignment motor. Check the alignment home position sensor. Checkthe aligning plate drive mechanism. Replace
the finisher controller PCB.

Code: E5F3-0002

Description:
Saddle alignment errorThe aligning plate home position sensor does not go off when the alignment motor hasbeen driven
for 1 sec. Alignment motor (M5S)/aligning plate home position sensor (PI5S)
Remedy:
Check the alignment motor. Check the alignment home position sensor. Checkthe aligning plate drive mechanism. Replace
the finisher controller PCB.

Code: E5F4-0001

Description:
Saddle rear stapling errorThe stitching home position sensor does not go on when the stitch motor (rear) has beenrotated
in reverse for 0.5 sec or more. Stitch motor (rear; M6S)/stitching home positionsensor (rear; MS5S)

Remedy:
Replace the stitcher (rear). Check the harness. Replace the finisher controllerPCB.

Code: E5F4-0002

Description:
Saddle rear stapling errorThe stitching home position sensor does not go off when the stitch motor (rear) has beenrotated
in normal direction for 0.5 sec or more. Stitch motor (rear; MS)/stitching homeposition sensor (rear; MS5S)

Remedy:
Replace the stitcher (rear). Check the harness. Replace the finisher controllerPCB.

Code: E5F5-0001

Description:
Saddle front stapling errorThe stitching home position sensor does not go on when the stitch motor (front) has
beenrotated in reverse for 0.5 sec or more. Stitch motor (front; M7S)/stitching home positionsensor (front; MS7S)

Remedy:
Replace the stitcher (front). Check the harness. Replace the finisher controllerPCB.

Code: E5F5-0002

Description:
Saddle front stapling errorThe stitching home position sensor does not go off when the switch motor (front) has
beenrotated in normal direction for 0.5 sec or more. Stitch motor (front; M7S)/stitching homeposition sensor (front; MS7S)

Remedy:
Replace the stitcher (front). Check the harness. Replace the finisher controllerPCB.

Code: E5F6-0001

Description:
Saddle butting errorThe paper butting plate home position sensor does not go on when the paper butting platemotor has
been driven for 0.3 sec. Paper butting plate motor (M8S)/paper butting platehome position sensor (PI14S)

Remedy:
Check the paper butting plate motor. Check the paper butting plate homeposition sensor. Replace the finisher controller
PCB.

Code: E5F6-0002
Description:
Saddle butting errorThe paper butting plate home position sensor does not go off when the paper butting plate
Remedy:
Check the alignment motor. Check the alignment home position sensor. Checkthe aligning plate drive mechanism. Replace
the finisher controller PCB.

Code: E5F4-0001

Description:
Saddle rear stapling errorThe stitching home position sensor does not go on when the stitch motor (rear) has beenrotated
in reverse for 0.5 sec or more. Stitch motor (rear; M6S)/stitching home positionsensor (rear; MS5S)

Remedy:
Replace the stitcher (rear). Check the harness. Replace the finisher controllerPCB.

Code: E5F4-0002

Description:
Saddle rear stapling errorThe stitching home position sensor does not go off when the stitch motor (rear) has beenrotated
in normal direction for 0.5 sec or more. Stitch motor (rear; MS)/stitching homeposition sensor (rear; MS5S)

Remedy:
Replace the stitcher (rear). Check the harness. Replace the finisher controllerPCB.

Code: E5F5-0001

Description:
Saddle front stapling errorThe stitching home position sensor does not go on when the stitch motor (front) has
beenrotated in reverse for 0.5 sec or more. Stitch motor (front; M7S)/stitching home positionsensor (front; MS7S)

Remedy:
Replace the stitcher (front). Check the harness. Replace the finisher controllerPCB.


Code: E5F5-0002

Description:
Saddle front stapling errorThe stitching home position sensor does not go off when the switch motor (front) has
beenrotated in normal direction for 0.5 sec or more. Stitch motor (front; M7S)/stitching homeposition sensor (front; MS7S)

Remedy:
Replace the stitcher (front). Check the harness. Replace the finisher controllerPCB.

Code: E5F6-0001

Description:
Saddle butting errorThe paper butting plate home position sensor does not go on when the paper butting platemotor has
been driven for 0.3 sec. Paper butting plate motor (M8S)/paper butting platehome position sensor (PI14S)

Remedy:
Check the paper butting plate motor. Check the paper butting plate homeposition sensor. Replace the finisher controller
PCB.

Code: E5F6-0002

Description:
Saddle butting errorThe paper butting plate home position sensor does not go off when the paper butting plate
Description:
Saddle connector errorThe connector of the paper butting plate leading edge sensor has been identified as
beingdisconnected. Connector of paper butting plate leading edge sensor (PI15S)

Remedy:
Connect the connector of the paper butting plate leading edge sensor. Check theharness. Replace the finisher controller
PCB.

Code: E5F9-0001

Description:
Saddle switch errorThe inlet cover switch has been identified as being open for 1 sec or more after the start ofprinting or
the start of initial rotation with the following sensors identifying their respectivecovers as being closed: -inlet cover sensor
(PI9S) -nt cover open/closed sensor (PI2S) -delivery cover sensor (PI3S) Or, the front over switch (MS2S) or the delivery
cover switch(MS3S) is open. Inlet cover switch (MS1S)/front cover switch (MS2S)/delivery coverswitch (MS3S)

Remedy:
Check the inlet cover switch. Check the inlet cover sensor. Check the front coveropen/ closed sensor. Check the delivery
cover sensor. Replace the finisher controllerPCB.

Code: E5F9-0002

Description:
Saddle switch errorThe front cover switch has been identified as being open from the start of printing or thestart of initial
rotation with the following sensors identifying their respective covers asbeing closed. -inlet cover sensor (PI9S) -front cover
open/closed sensor (PI2S) -deliverycover sensor (PI3S) -front cover switch (MS2S)/delivery cover switch (MS3S)

Remedy:
Check the front cover switch. Check the inlet cover sensor. Check the frontcover open/ closed sensor. Check the delivery
cover sensor. Replace the finishercontroller PCB.

Code: E5F9-0003

Description:
Saddle switch errorThe delivery cover switch has been identified as being open after the start of printing orthe start of
initial rotation of the host machine with the following sensors identifying theirrespective covers as being closed: -inlet
cover sensor (PI9S) -front cover open/closedsensor (PI2S) -delivery cover sensor (PI3S) - delivery cover switch (MS3S)

Remedy:
Check the delivery cover switch. Check the inlet cover sensor. Check the inletcover sensor. Check the front cover
open/closed sensor. Check the delivery cover sensor.Replace the finisher controller PCB.

Code: E602-0001

Description:
There is an error on the hard disk.[Cause] An HDD detection error has occurred. The HDD cannot be detected. The
HDDdoes not become ready. The HDD returns an error. [Detection] while boot ROM is insession BARSAC startup, mounting
(usrIde) [Timing of Detection] once at startup

Remedy:

Code: E602-0002
Description:
There is an error on the hard disk.[Cause] There is no startup file. The program for the main CPU does not exist on the
HDDor in BOOTDEV/BOOT, and so on. [Detection] while boot ROM is in use at time of systemfile loading (usrIde) [Timing of
Detection] once at startup

Remedy:

Code: E602-0003

Description:
There is an error on the hard disk.[Cause] An HD write abort error has occurred. The sectors for BOOTDEV on the HDcannot
be read. [Detection] BARSAC (all; at time of bootable startup) [Timing of Detection]once at startup

Remedy:
Code: E602-0006

Description:
There is an error on the hard disk.[Cause] A subbootable that matches the PDL type does not exit in BOOTDEV/BOOT.
[Detection] during loading of sub boot in oclibroot [Timing of Detection] once at bootablestartup

Remedy:

Code: E602-0007

Description:
There is an error on the hard disk.[Cause] An ICC profile that matches the PDL type does not exist in BOOTDEV/PDL.
[Detection] beginning of oclibroot; judgment based on functions of PDL team that arecalled in [Timing of Detection] once
at bootable startup

Remedy:

Code: E602-01XX

Description:
There is an error on the hard disk./DOSDEV is faulty

Remedy:

Code: E602-02XX

Description:
There is an error on the hard disk./FSTDEV is faulty.

Remedy:

Code: E602-03XX

Description:
There is an error on the hard disk./DOSDEV2 is faulty.

Remedy:

Code: E602-04XX

Description:
There is an error on the hard disk./FSTPDEV is faulty.

Code: E602-05XX
Description:
There is an error on the hard disk./DOSDEV3 is faulty.

Remedy:

Code: E602-06XX

Description:
There is an error on the hard disk./PDLDEV is faulty.

Remedy:

Code: E602-07XX

Description:
There is an error on the hard disk./DOSDEV4 is faulty.
Code: E602-08XX

Description:
There is an error on the hard disk./BOOTDEV is faulty.

Remedy:

Code: E602-09XX

Description:
There is an error on the hard disk./DOSDEV5 is faulty.

Remedy:

Code: E602-FFXX

Description:
There is an error on the hard disk.There is an error in a partition that cannot be identified.

Remedy:

Code: E604-0000

Description:
The image memory is faulty or is inadequate.The memory size does not match the model.

Remedy:
Increase the memory.

Code: E609-0008

Description:
There is an error on the HDD. At startup, the HDD fails to reach a specific temperature level within a specific period oftime.

Remedy:
Replace the hard disk. Replace the DC controller PCB.

Code: E609-0009

Description:
There is an error on the HDD. At time of sleep recovery, the temperature fails to reach a specific level.

Remedy:
Replace the hard disk. Replace the DC controller PCB.

Code: E610
Description:
The HDD coding key is faulty.

Remedy:

Code: E677-0001

Description:
Failure in PS Printer Kit-AA1Failure in exhaust fan of PS Printer Kit-AA1

Remedy:
- Check connection of the exhaust fan connector - Replace the exhaust fan

Code: E677-0003

Description:
Failure in PS Printer Kit-AA1 Abnormal detection with configuration check when PS Printer Kit-AA1 is started
Remedy:
- Check cable connection - Reinstall system of PS Printer Kit-AA1

Code: E677-0004

Description:
Failure in PS Printer Kit-AA1Failure in CPU cooling fan of PS Printer Kit-AA1

Remedy:
- Check connection of the connector for cooling CPU - Replace CPU cooling fan

Code: E677-0010

Description:
Failure in PS Printer Kit-AA1In the case that other type of controller is connected

Remedy:
- Check connection of controller that supports this machine

Code: E677-0080

Description:
Failure in PS Printer Kit-AA1Communication error between PS Printer Kit-AA1 and the main controller of the hostmachine
after PS Printer Kit-AA1 is started

Remedy:
- After checking connection, turn ON the power again. - Reinstall system of PSPrinter Kit-AA1.

Code: E710-0001

Description:
There is an error in the initialization of the IPC.The machine fails to become ready 3 sec or less after the IPC chip startup

Remedy:
Check the cable.

Code: E711-0001

Description:
There is an error in the IPC communication.The occurrence of an error has been recorded in the error register of the IPC
chip 4 timesor more within 1.5 sec.

Remedy:
Check the cable.

Code: E713-0000

Description:
There is an error in the communication with the finisher or 3 Way Unit-A1.The communication with the finisher does not
resume within 5 sec after it has beendisrupted.
Remedy:
Check the cable. Replace the DC controller PCB. Replace the finisher controllerPCB.

Code: E716-0000

Description:
There is an error in the communication with the pedestal. After the presence of a pedestal has been detected, the
communication fails to be normalfor 5 sec.

Remedy:
Check the cable. Replace the DC controller PCB. Replace the pedestal drivePCB.
Code: E716-0010

Description:
There is an error in the communication with the pedestal.When the communication with the 3 Way Unit-A1 is faulty after
detecting the connectionwith the finisher.

Remedy:
Install the 3 Way Unit-A1. Replace the DC controller PCB after checking thecable

Code: E717-0001

Description:
There is an error in the communication with the NE controller.The NE controller is not connected at power on, although it
was connected before thepower was turned off because of an error.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR.

Code: E717-0002

Description:
There is an error in the communication with the NE controller. An IPC error has occurred while the NE controller is in
operation. There is an open circuitfor the IPC. An error has occurred, and the IPC communication remains disabled.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR.

Code: E719-0001

Description:
There is a coin vendor error.The coin vendor is not connected when the power is turned on, although it was
connectedbefore the power was turned off because of an error.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR.

Code: E719-0002

Description:
There is a coin vendor error.While the coin vendor is in operation, an IPC error has occurred, IPC has developed anopen
circuit, or an error preventing recovery of IPC communication has occurred. An opencircuit has been detected in the line
for the pickup/delivery signal. An illegal signal hasbeen detected.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR
Remedy:
Check the cable. Replace the DC controller PCB. Replace the finisher controllerPCB.

Code: E716-0000

Description:
There is an error in the communication with the pedestal. After the presence of a pedestal has been detected, the
communication fails to be normalfor 5 sec.

Remedy:
Check the cable. Replace the DC controller PCB. Replace the pedestal drivePCB.

Code: E716-0010

Description:
There is an error in the communication with the pedestal.When the communication with the 3 Way Unit-A1 is faulty after
detecting the connectionwith the finisher.
Remedy:
Install the 3 Way Unit-A1. Replace the DC controller PCB after checking thecable

Code: E717-0001

Description:
There is an error in the communication with the NE controller.The NE controller is not connected at power on, although it
was connected before thepower was turned off because of an error.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR.

Code: E717-0002

Description:
There is an error in the communication with the NE controller. An IPC error has occurred while the NE controller is in
operation. There is an open circuitfor the IPC. An error has occurred, and the IPC communication remains disabled.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR.

Code: E719-0001

Description:
There is a coin vendor error.The coin vendor is not connected when the power is turned on, although it was
connectedbefore the power was turned off because of an error.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR.

Code: E719-0002

Description:
There is a coin vendor error.While the coin vendor is in operation, an IPC error has occurred, IPC has developed anopen
circuit, or an error preventing recovery of IPC communication has occurred. An opencircuit has been detected in the line
for the pickup/delivery signal. An illegal signal hasbeen detected.

Remedy:
Check the cable; thereafter, reset the condition in service mode:COPIER>FUNCTION>CLEAR>ERR
Description:
There is a PDL software error. An error that may be critical to the system (e.g., failed initialization) has occurred.

Remedy:
1. Execute PDL resetting. 2. Turn on the power once again.

Code: E730-9004

Description:
There is a PDL software error.There is an error in the communication (PAI) with an external controller.

Remedy:
1. Turn on the power once main. 2. Check the connection of the open I/F boardand the cable. 3. Replace the board for the
external controller open I/F. 4. Replace themain board.

Code: E730-9005

Description:
There is a PDL software error.There is a fault in the connector of the vide cable to the external controller.

Remedy:
1. Turn on the power once main. 2. Check the connection of the open I/F boardand the cable. 3. Replace the board for the
external controller open I/F. 4. Replace themain board.
Code: E730-A006

Description:
There is a PDL software error.The PDL board does not respond. A subbootable is faulty or absent.

Remedy:
1. Execute PDL resetting. 2. Turn on the power once again. 3. Check theconnection of the SURF board. 4. Re-install the
firmware. 5. Replace the main board.

Code: E730-A007

Description:
There is a PDL software error.There is a mismatch between the control software of the machine and the PDL
controlsoftware in regard to version.

Remedy:
1. Execute PDL resetting. 2. Turn on the power once again. 3. Execute systemformatting (all), and reinstall the system.

Code: E730-B013

Description:
There is a PDL software error.There is corruption in the font data.

Remedy:
1. Turn on the power once again. 2. Re-install the software. 3. Execute systemformatting (all), and reinstall the system.

Code: E732-0001

Description:
There is an error in the communication with the scannerThere is a DDI-S communication error.

Remedy:
1. Check the connector used to connect the scanner. 2. Check the power supplyof the scanner (to see if initialization takes
place at startup). 3. Replace the readercontroller, scanner board, or main board as necessary.

Code: E732-0010
Description:
There is an error in the communication with the scannerFault in detection of DDI-S Vsync signal

Remedy:
1. Check the connector used to connect the scanner. 2. Check the power supplyof the scanner (to see if initialization takes
place at startup). 3. Replace the readercontroller, scanner board, or main board as necessary.

Code: E732-9999

Description:
There is an error in the communication with the scanner A scanner is first detected from the printer model. (Not an error
code but only themessage 'Turn the main power switch OFF&ON again' is displayed on the users screen.The error is
recorded in service mode > DISPLAY > ERR

Remedy:
Turn the main power switch off/on

Code: E733-0000

Description:
There is an error in the communication with the printer At startup, communication with the printer fails

Remedy:
1. Check the connector used to connect to the printer. 2. Check the powersupply of the printer (to see if initialization takes
place at startup). 3. Replace the DCcontroller or the main board.

Code: E733-0001
Description:
There is an error in the communication with the printerThere is a DDI-P communication error

Remedy:
1. Check the connection with the printer. 2. Check the power supply of theprinter (to see if initialization takes place at
startup). 3. Replace the DC controller or themain board.

Code: E733-0010

Description:
There is an error in the communication with the printerFault in detection of DDI-P Vsync signal

Remedy:
1. Check the connection with the printer. 2. Check the power supply of theprinter (to see if initialization takes place at
startup). 3. Replace the DC controller or themain board.

Code: E733-0020

Description:
There is an error in the communication with the printerError in DDI-P communication

Remedy:
2. Check the power supply of the printer (to see if initialization takes place at startup). 3. Replace the DC controller or the
main board.

Code: E733-0021

Description:
There is an error in the communication with the printer Error in DDI-P communication

Remedy:
1. Check the connection with the printer. 2. Check the power supply of the printer (to see if initialization takes place at
startup). 3. Replace the DC controller or the main board.
Code: E740-0002

Description:
There is an error on the Ether board.The MAC address is illegal.

Remedy:
Replace the LAN card.

Code: E743-0000

Description:
There is an error in the DDI communication. An SCI error has occurred. The received data is faulty. A reception timeout
condition hasoccurred. An SEQ timeout error has occurred.

Remedy:
Disconnect and then connect the flexible cable used to connect the reader unitand the printer unit. Replace the following
as necessary: flexible cable, reader controllerPCB, main controller PCB.

Code: E744-0001

Description:
There is an error in the language file/boot ROM.The version of the language file on the HDD and that of the bootable do
not match.

Remedy:
Download a language file of the correct version.

Code: E744-0002
Description:
There is an error in the language file/boot ROM.The size of the language file on the HDD is too large.

Remedy:
Download a language file of the correct version.

Code: E744-0003

Description:
There is an error in the language file/boot ROM.There is no language file on the HDD indicated by config.txt for a
switchover.

Remedy:
Download a language file of the correct version.

Code: E744-0004

Description:
There is an error in the language file/boot ROM. An attempt to switchover to a language on the HDD fails.

Remedy:
Download a language file of the correct version.

Code: E744-1000

Description:
There is an error in the language file/boot ROM.The boot ROM that is mounted is of the wrong type

Remedy:
Replace the boot ROM with one of the model in question.

Code: E744-2000

Description:
There is an error in the language file/boot ROM.The engine ID indicated by the software ID is illegal.

Remedy:
Replace it with a software ID of the correct model.

Code: E744-3xxx

Description:
There is an error in the language file/boot ROM.Disagreement between the installed memory and the boot ROM

Remedy:
Confirm and correct the installed memory and the boot ROM.

Code: E745-0001

Description:
There is a fault on the TokenRing board. An attempt at PCI initialization has failed.

Remedy:
1. Disconnect and then connect the TokenRing board. 2. Replace the TokenRingboard.

Code: E745-0002

Description:
There is a fault on the TokenRing board.The MAC address is faulty.

Remedy:
1. Replace the TokenRing board.
Code: E745-0003

Description:
There is a fault on the TokenRing board.There is an error in the acquisition/setting of board information.

Remedy:
1. Replace the TokenRing board.

Code: E745-0004

Description:
There is a fault on the TokenRing board.There is a connection error.

Remedy:
1. Check the connection of the cable. 2. Replace the cable. 3. Check the powersource of the MAU. 4. Replace the MAU. 5.
Replace the TokenRing board.

Code: E745-0005

Description:
There is a fault on the TokenRing board.Other Errors

Remedy:

Code: E746-0003

Description:
The accessories board is of the wrong type. At startup, a board for a different model has been detected.

Remedy:
Replace the UFR board of the correct type (model).

Code: E748-2000

Description:
There is a mismatch between controller board and SDRAM size. An error occurs when accessing the chip on the main
controller PCB.

Remedy:
Replace the main controller PCB.

Code: E748-2001

Description:
There is a mismatch between controller board and SDRAM size. An error occurs when accessing the memory on the main
controller PCB.

Remedy:
1. Unplug/plug in the memory. 2. Replace the main controller PCB.

Code: E748-4910
Description:
There is a mismatch between controller board and SDRAM size. A controller board that does not match the product is
defected.

Remedy:
- Replace the main controller PCB.

Code: E804-0000

Description:
Error in power supply cooling fanFailure in power supply cooling fan (while the fan is not working) When lock signal
isdetected for 5 sec while the fan is stopped.

Remedy:
- Disconnect and then connect the connector (J303) on DC controller PCB. -Replace the power supply cooling fan - Replace
DC controller PC

Code: E804-

Description:
Error in power supply cooling fanFailure in rotation of power supply cooling fan When lock signal failed to be detected for
5sec while the fan is driven.

Remedy:
- Disconnect and then connect the connector (J303) on DC controller PCB. -Replace the power supply cooling fan - Replace
DC controller PCB

Code: E805-0000

Description:
There is a fan error.Failure in heat exhaust fan (front) (FM2) When lock signal is detected for 5 sec while thefan is stopped.

Remedy:
- Replace the heat exhaust fan (front) - Replace DC controller PCB.

Code: E805-0001

Description:
There is a fan error.Failure in rotation of heat exhaust fan (front) (FM2) When lock signal failed to be detectedfor 5 sec
while the fan is driven.

Remedy:
- Replace the heat exhaust fan (front) - Replace DC controller PCB

Code: E805-0002

Description:
There is a fan error.Failure in heat exhaust fan (rear) (FM1) When lock signal is detected for 5 sec while thefan is stopped.

Remedy:
- Replace the heat exhaust fan (rear) - Replace DC controller PCB

Code: E805-0003

Description:
There is a fan error.Failure in rotation of heat exhaust fan (rear) (FM1) When lock signal failed to be detectedfor 5 sec while
the fan is driven.

Remedy:
- Replace the heat exhaust fan (rear) - Replace DC controller PCB

Code: E911

Description:
Error in memory leak