恒通未来 HTFUTURE CO.

, LIMITED
www.htfuture.com The leader of fiber
transmission

10/100/1000 BASE-T Copper SFP Transceiver

HTST-ERTx

Features
 Up to 1.25 Gb/s bi-directional data links
 Link lengths at 1.25 Gb/s up to 100 meter
 10/100/1000 BASE-T operation in host
systems with SGMII interface
 Support TX_ disable and no Link function
 Compliant with SFP MSA
 Compact RJ-45 connector assembly
 Hot-pluggable SFP Footprint
 Single + 3.3V Power Supply
 Fully Metallic Enclosure for Low EMI
 Low power dissipation(1.05W typical) Applications
 RoHS compliant and lead-free
 LAN 1000Base-T
 Operating case temperature
 Switch to Switch Interface
Commercial: 0 ~ +70oC
 Router/Server interface
Extended: -10 ~ +80oC
 Switched backplane
Industrial: -40 ~ +85oC
applications

Link Indicator TX_

Data Rate Transmission Temperature (oC)
Part Number on RX_ LOS disable
(Mb/s) Distance(m) (Operating Case)
pin with PHY

HTST-ERTC 10/100/1000 100 No Yes 0~70 commercial

HTST-ERTE 10/100/1000 100 No Yes -10~80 Extended

HTST-ERTI 10/100/1000 100 No Yes -40~85 Industrial

Part Number Ordering Information

1. Absolute Maximum Ratings

Tel.: (+86)755-23777185 Email: [email protected] www.htfuture.com

1
 恒通未来 HTFUTURE CO., LIMITED
www.htfuture.com The leader of fiber
transmission
It has to be noted that the operation in excess of any individual absolute maximum ratings might cause
permanent damage to this module.

Parameter Symbol Min Max Unit Notes

o
Storage Temperature TS -40 85 C

Power Supply Voltage VCC -0.5 3.6 V

Relative Humidity (non-condensation) RH 5 95 %

2. Recommended Operating Conditions and Power Supply Requirements

Parameter Symbol Min Typical Max Unit Notes

0 70 commercial
o
Operating Case Temperature TOP -10 80 C extended

-40 85 industrial

Power Supply Voltage VCC 3.135 3.3 3.465 V

Data Rate 10 1000 Mb/s

Link Distance (SMF) D 100 m

3. General Description
HTF’ HTST-ERTx Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source
Agreement (MSA). They are compatible with the Gigabit Ethernet standards as specified in IEEE STD
802.3. The 10/100/1000 BASE-T physical layer IC (PHY) can be accessed via I2C, allowing access to all
PHY settings and features.

The HTST-ERTx is compatible with 1000BASE-X auto-negotiation and support a SERDES, but does not
have a link indication feature.

4. Pin Assignment and Pin Description

Tel.: (+86)755-23777185 Email: [email protected] www.htfuture.com

2
 恒通未来 HTFUTURE CO., LIMITED
www.htfuture.com The leader of fiber
transmission

Figure1. Diagram of host board connector block pin numbers and names

PIN Name Name/Description Notes

1 VEET Transmitter Ground (Common with Receiver Ground) 1

2 TXFAULT Transmitter Fault.

3 TXDIS Transmitter Disable. Laser output disabled on high or open.

4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 2

5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 2

6 MOD_DEF(0) Module Definition 0. Grounded within the module. 2

7 Rate Select No connection required

8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 3

9 VEER Receiver Ground (Common with Transmitter Ground) 1

10 VEER Receiver Ground (Common with Transmitter Ground) 1

11 VEER Receiver Ground (Common with Transmitter Ground) 1

12 RD- Receiver Inverted DATA out. AC Coupled

13 RD+ Receiver Non-inverted DATA out. AC Coupled

14 VEER Receiver Ground (Common with Transmitter Ground) 1

15 VCCR Receiver Power Supply

Tel.: (+86)755-23777185 Email: [email protected] www.htfuture.com

3
 恒通未来 HTFUTURE CO., LIMITED
www.htfuture.com The leader of fiber
transmission

16 VCCT Transmitter Power Supply

17 VEET Transmitter Ground (Common with Receiver Ground) 1

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled.

19 TD- Transmitter Inverted DATA in. AC Coupled.
20 VEET Transmitter Ground (Common with Receiver Ground) 1

Notes:
1. Circuit ground is connected to chassis ground
2. Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF (0) pulls line low to indicate
module is plugged in.
3. LVTTL compatible with a maximum voltage of 2.5V.

5. Power Supply Interface Electronic Characteristics

The HTST-ERTx has an input voltage range of 3.3 V ± 5%. The 4 V maximum voltage is not allowed for
continuous operation.

Parameter Symbol Min. Typical Max Unit Notes

Power Consumption 1.2 W

Supply Current Icc 375 mA

Input Voltage Tolerance -0.3 4.0 V

Surge Surge 30 mV

Current current See caution note

Notes: Power consumption and surge current are higher than the specified values in the SFP MSA

6. Low-Speed Signals Electronic Characteristics

MOD_DEF (1) (SCL) and MOD_DEF (2) (SDA) are open drain CMOS signals. Both MOD_ DEF (1) and MOD_DEF (2) must be pulled up to host_ VCC.

Parameter Symbol Min. Typical Max Unit Notes

SFP Output 4.7k to 10k pull-up to

VOL 0 0.5 V
LOW host_ Vcc.
SFP Output host_ Vcc - host_ Vcc 4.7k to 10k pull-up to
VOH V
HIGH 0.5 +0.3 host_ Vcc.
SFP Input 4.7k to 10k pull-up to
VIL 0 0.8 V
LOW Vcc.

Tel.: (+86)755-23777185 Email: [email protected] www.htfuture.com

4
 恒通未来 HTFUTURE CO., LIMITED
www.htfuture.com The leader of fiber
transmission

SFP Input 4.7k to 10k pull-up to

VIH 2 Vcc + 0.3 V
HIGH Vcc.

7. High-Speed Electrical Interface

All high-speed signals are AC-coupled internally.

High-Speed Electrical Interface, Transmission Line-SFP

Parameter Symbol Min. Typical Max Unit Notes

5-level encoding, per

Line Frequency fL 125 MHz
IEEE 802.3
Tx Output
Zout,TX 100 Ohm Differential
Impedance
Rx Input
Zin,RX 100 Ohm Differential
Impedance
High-Speed Electrical Interface, Host-SFP
Single Ended
Vinsing 250 1200 mV Single ended
Data Input Swing
Single Ended
Data Output Voutsing 350 800 mV Single ended
Swing
Rise/Fall Time Tr,Tf 175 ps 20%-80%
Tx Input
Zin 50 Ohm Single ended
Impedance
Rx Output
Zout 50 Ohm Single ended
Impedance

8. General Specifications
Parameter Symbol Min. Typical Max Unit Notes
Data Rate BR 10 1000 Mb/s IEEE 802.3 compatible
Category 5 UTP. BER
Cable Length L 100 m
<10-12

Notes:
1. Clock tolerance is +/- 50 ppm
2. By default, the HTST-ERTx is a full duplex device in preferred master mode
3. Automatic crossover detection is enabled. External crossover cable is not required
4. By default, 1000 BASE-T operation requires the host system to have an SERDES interface with no clocks.

Tel.: (+86)755-23777185 Email: [email protected] www.htfuture.com

5
 恒通未来 HTFUTURE CO., LIMITED
www.htfuture.com The leader of fiber
transmission

9. Serial Communication Protocol

HTST-ERTx supports the 2-wire serial communication protocol outlined in the SFP MSA. It uses an Atmel
AT24C02D 256 byte EEPROM with an address of A0h

Parameter Symbol Min. Typical Max Unit Notes

I 2C Clock Rate 0 100000 Hz

10. Mechanical Dimensions

Figure 2. Mechanical Outline

Tel.: (+86)755-23777185 Email: [email protected] www.htfuture.com