AMERICAN NATIONAL STANDARD

ANSI/ISA–7.0.01–1996
Formerly ANSI/ISA–S7.0.01–1996

Quality Standard for

Instrument Air

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Approved 12 November 1996

TM

ISA–The Instrumentation,
Systems, and
Automation Society
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---
ANSI/ISA-7.0.01-1996, Quality Standard for Instrument Air
ISBN: 1-55617-606-6

Copyright ã 1996 by the Instrument Society of America. All rights reserved. Printed in the United
States of America. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or
otherwise), without the prior written permission of the publisher.

ISA
67 Alexander Drive
P.O. Box 12277
Research Triangle Park, North Carolina 27709

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Preface

This preface, as well as all material contained in the footnotes and annexes, is included for
information purposes and is not part of the ANSI/ISA-7.0.01-1996.
This Standard has been prepared as a part of the service of ISA, the international society for
measurement and control, toward a goal of uniformity in the field of instrumentation. To be of real
value, this document should not be static but should be subject to periodic review. Toward this
end, the Society welcomes all comments and criticisms and asks that they be addressed to the
Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P.O. Box 12277; Research
Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288; E-mail:
[email protected].
The ISA Standards and Practices Department is aware of the growing need for attention to the
metric system of units in general, and the International System of Units (SI) in particular, in the
preparation of instrumentation standards, recommended practices, and technical reports. The
Department is further aware of the benefits to USA users of ISA Standards of incorporating
suitable references to the SI (and the metric system) in their business and professional dealings
with other countries. Toward this end, this Department will endeavor to introduce SI and
acceptable metric units as optional alternatives to English units in all new and revised standards,
recommended practices, and technical reports to the greatest extent possible. The Metric
Practice Guide, which has been published by the Institute of Electrical and Electronics Engineers
as ANSI/IEEE Standard 268-1982, and future revisions, will be the reference guide for
definitions, symbols, abbreviations, and conversion factors. SI (metric) conversions in this
Standard are given only to the precision intended in selecting the original numerical value. When
working in SI units, the given SI value should be used; when working in customary U.S. units, the
given U.S. value should be used.
It is the policy of ISA to encourage and welcome the participation of all concerned individuals and
interests in the development of ISA standards, recommended practices, and technical reports.
Participation in the ISA standards-making process by an individual in no way constitutes
endorsement by the employer of that individual, of ISA, or of any of the standards that ISA
develops.
This Standard, complete with all updates, incorporates the following previous SP7
Subcommittees and documents:

SP7.1 Pneumatic Control Circuit Pressure Test

SP7.3 Air Quality Standards for Pneumatic Instruments
SP7.3 Application and Tests for Quality Standards for Instrument Air
SP7.4 Air Pressures for Pneumatic Controllers and Transmission
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Systems
SP7.6 Pneumatic Control Circuit Transmission Distances

ISA-RP7.1-1956 Pneumatic Control Circuit Pressure Test

ISA-7.3-1975 (R1981) Quality Standard for Instrument Air
ISA-7.4-1981 Air Pressures for Pneumatic Controllers, Transmitters and
Transmission Systems
ISA-RP7.7-1984 Producing Quality Instrument Air

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 3
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 The following people served as members of ISA Committee SP7:

NAME COMPANY

D. Hendrick, Chairman Consultant

C. Parry, Co-Chairman Pacific Gas & Electric Company
T. McAvinew, Managing Director Metro Wastewater Reclamation District
R. Hires, Secretary Tennessee Valley Authority
C. Essex Detroit Edison
B. Fitzgerald Fisher Service Company
D. Frey Computer & Control Consultants
G. Hagerty, Jr.* Retired/Consultant
M. Kostelnik BGE
D. Lewko Bantrel, Inc.
B. Lyke Atlas Copco M. NayOmaha Public Power
H. Ornstein U.S. Nuclear Regulatory Commission
P. Papish* Pall Pneumatic Products Corporation
F. Quinn* Retired/Consultant
L. Sweezo GPU Nuclear Corporation
J. Werner New York Power Authority
M. Widmeyer Washington Public Power Supply System
G. Wilkinson Arizona Public Service Company

This Standard was approved for publication by the ISA Standards and Practices Board on
June 5, 1996.

NAME COMPANY

M. Widmeyer, Vice President Washington Public Power Supply System

H. Baumann H. D. Baumann, Inc.
D. Bishop Chevron USA Production Company
P. Brett Honeywell Industrial Automation Controls
W. Calder III Calder Enterprises
H. Dammeyer Phoenix Industries, Inc.
R. Dieck Pratt & Whitney
W. Holland Southern Company Services, Inc.
A. Iverson Lyondell Petrochemical Company
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

K. Lindner Endress + Hauser GmbH + Company

T. McAvinew Metro Wastewater Reclamation District
A. McCauley, Jr. Chagrin Valley Controls, Inc.
G. McFarland Honeywell Industrial Automation Controls
E. Montgomery Fluor Daniel, Inc.
D. Rapley Rapley Engineering Services
R. Reimer Rockwell Automation A-B
R. Webb Pacific Gas & Electric Company
W. Weidman Consultant
J. Weiss Electric Power Research Institute
J. Whetstone National Inst. of Standards & Technology

*Non-voting members

Copyright The Instrumentation, Systems, and Automation Society 4 ANSI/ISA-7.0.01-1996

Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 NAME COMPANY

H. Wiegle Canus Corporation

C. Williams Eastman Kodak Company
G. Wood Graeme Wood Consulting
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

M. Zielinksi Fisher-Rosemount

Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996 Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 5
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Contents

1 Scope ....................................................................................................................................... 9

2 Purpose.................................................................................................................................... 9

3 Definitions ............................................................................................................................... 9

4 Instrument air system design ...............................................................................................11

5 Instrument air, quality standard ...........................................................................................11

5.1 Pressure dew point ...................................................................................................... 11
5.2 Particle size ................................................................................................................. 11
5.3 Lubricant content ......................................................................................................... 11
5.4 Contaminants .............................................................................................................. 12

Annexes

A — References.......................................................................................................................... 13
B — Equipment and application guidelines for producing instrument air.................................... 17
B.1 Instrument air system design ...................................................................................... 17
B.2 Air quality considerations ............................................................................................ 25
B.3 Instrument air supply pressure and pneumatic pressure transmission signal............. 27
C — Guideline for testing pneumatic systems ........................................................................... 29
C.1 Application .................................................................................................................. 29
C.2 Inspections and testing ............................................................................................... 29
C.3 Tests ........................................................................................................................... 30

Figures

B.1 — Compressed air-drying system: desiccant dryer ........................................................... 21

B.2 — Compressed air-drying system: refrigerant dryer (air cooled) ....................................... 22
B.3 — Compressed air-drying system: refrigerant dryer (water cooled) .................................. 23
C.1 — Moisture content of air vs. dewpoint.............................................................................. 31

Tables

B.1 — Typical compressed air dryer types .............................................................................. 20

B.2 — Typical spans, ranges, and supply pressures ............................................................... 27

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 7
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 1 Scope

The scope of this Standard is

a) to provide limits for moisture content in instrument quality air;
b) to provide limits for entrained particle size and oil content in instrument quality air;
c) to establish an awareness of possible sources of corrosive or toxic contamination
entering the air system through the compressor suction, plant air system cross
connection, or instrument air connections directly connected to processes;
d) to establish standard air supply pressures (with limit values) and operating ranges for
pneumatic devices;
e) to specify ranges of pneumatic transmission signals used in measurement and control
systems between elements of systems. It includes, but is not limited to, the following:
1) Pneumatic controllers

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---
2) Pneumatic transmitters and information transmission systems
3) Current-to-Pressure transducers
4) Pneumatic control loops; and
f) to establish criteria for testing compliance with instrument-quality air standards.

2 Purpose

The purpose of this Standard is to establish a standard for instrument quality air.

3 Definitions

3.1 ambient temperature: The temperature of the medium surrounding a device.

3.2 dew point temperature: The temperature, referred to at a specific pressure, at which water
vapor condenses.

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 9
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 3.3 elements of measurement and control systems: Functional units or integrated
combinations thereof that ensure the transducing, transmitting, or processing of measured values,
control quantities or variables, and reference variables. A valve actuator in combination with a
current to pressure transducer, valve positioner, or a booster relay is considered an element that
receives the standard pneumatic transmission signal or standard electric current transmission
signal.

3.4 instrument quality air: Air, which is the working media for various devices, that has been
treated to minimize liquid and particulate matter.
NOTE — Some individual devices may require further conditioning of the air (filtration,
dehumidification) to ensure reliable operation.

3.5 lower limit: The lowest value of the measured variable that a device can be adjusted to
measure.

3.6 measured value: The numerical quantity resulting, at the instant under consideration, from
the information obtained by a measuring device.

3.7 micrometer (m): A metric measure with a value of 10-6 meters or 0.000001 meter
(previously referred to as "micron").

3.8 parts per million (ppm): Represents parts per million and should be given on a weight
basis. The abbreviation shall be ppm (w/w). If inconvenient to present data on a weight basis
(w/w), it may be given in a volume basis; (v/v) must be stated after the term ppm; e.g.,
5 ppm (v/v) or 7 ppm (w/w).

3.9 pneumatic controller: A device that compares the value of a variable quantity or condition
to a selected reference and operates by pneumatic means to correct or limit the deviation.

3.10 pneumatic transmission system: A system that develops an output directly

corresponding to the input information for conveying information—comprising a transmitting
mechanism that converts input information into a corresponding air pressure, interconnecting
tubing, and a receiving element responsive to air pressure.

3.11 pressure dew point: The dew point value at line pressure of the compressed air system
(usually measured at the outlet of the dryer system or at any instrument air supply source prior to
pressure reduction). When presenting or referencing dew point, the value shall be given in terms
of the line pressure; e.g., -40°C (-40°F) dew point at 690 kPa (approximate) (100 psig).

3.12 range of a pneumatic transmission signal: The range determined by the lower and upper
limit of the signal pressure.

3.13 relative humidity: The ratio (expressed as a percentage) of the partial pressure of water
vapor contained in the air at a given temperature and pressure to the maximum partial pressure
of water vapor that could be present at the same temperature under saturated conditions.

3.14 span: The algebraic difference between the upper and lower range values.

3.15 supply pressure: The pneumatic supply pressure that enables the system element to
generate the pneumatic transmission signals specified to provide the final device with required
operational force.

3.16 upper limit: The highest value of the measured variable that a device can be adjusted to
measure.

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

10
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 4 Instrument air system design

The specifications for instrument air systems vary in order to meet a range of application
requirements. This makes the specification of any specific design requirements impractical, but
in general, a properly designed instrument air system should
a) provide a sufficient quantity of air to supply the highest anticipated load plus margin for
future growth including leakage;
b) provide the quality air required by the user; and
c) provide for maintenance and testing of the system.

5 Instrument air, quality standard

This Standard establishes four elements of instrument air quality for use in pneumatic
instruments (see Annex B.2).

5.1 Pressure dew point

The pressure dew point as measured at the dryer outlet shall be at least 10°C (18°F) below the
minimum temperature to which any part of the instrument air system is exposed. The pressure
dew point shall not exceed 4°C (39°F) at line pressure. A monitored alarm is preferred;
however, if a monitored alarm is unavailable, per shift monitoring is recommended. See Annex
B.2.1. See Table B-1, Note 3 when using a refrigerant dryer.

5.2 Particle size

A maximum 40 micrometer particle size in the instrument air system is acceptable for the majority
of pneumatic devices. Pneumatic devices that require instrument air with less than
40 micrometer particle sizes shall have additional filtration to meet the particulate size limit for the
device.
Subsequent to any maintenance or modification of the air system, maximum particle size in the
instrument air system should be verified to be less than 40 micrometers.
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 11
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 5.3 Lubricant content

The lubricant content should be as close to zero as possible, and under no circumstances shall it
exceed one (1) ppm w/w or v/v. Any lubricant in the compressed air system shall be evaluated
for compatibility with end-use pneumatic devices. For example, the use of automatic oilers is
strongly discouraged.*

5.4 Contaminants

Instrument air should be free of corrosive contaminants and hazardous gases, which could be
drawn into the instrument air supply. The air system intake should be monitored for
contaminants. If contamination exists in the compressor intake area, the intake should be moved
to a different elevation or location free from contamination. Some sources of contamination are
a) painting;
b) chemical cleaning; and
c) engine exhaust.

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

*For details on why the use of automatic oilers is strongly discouraged, read the United States Nuclear
Regulatory Commission Inspection Report IN 95-53 (refer to Annex A). Some cylinder-type actuators
recommend a lubricant. If an in-line automatic oiler is used in such a case, the location of the oiler must be
selected to minimize the amount of the air system exposed to the lubricant. Also, the other control devices
exposed to the lubricant must be of compatible material. The typical installation for an automatic oiler is at
the point of use. Often the oiler is an integral part of an actuator assembly.

12
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Annex A — References

NOTE — This annex is for information purposes only and is not part of ISA-7.0.01.

AMERICAN NATIONAL STANDARD INSTITUTE (ANSI)

ANSI/B93.2 Fluid Power Systems and Products, 1986

ANSI/B93.45M Pneumatic Fluid Power, Compressed Air Dryers, Methods for
Rating and Testing, 1982
ANSI/ANS-59.3 Nuclear Safety Criteria for Control Air Systems, 1992
ANSI/IEEE 268 Metric Practice, 1982
Available from: ANSI
11 W. 42nd Street, 13th Floor
New York, NY 10036 Tel. (212) 398-0023

AMERICAN PETROLEUM INSTITUTE (API)

API 550 Manual on Installation of Refinery Instruments and Control

Systems, Fourth Edition, Part 1, Section 9, February, 1980
Available from: API
1220 L Street, NW
Washington D.C. 20005 Tel. (202) 682-8232

AMERICAN SOCIETY OF HEATING, REFRIGERATING, AND AIR CONDITIONING

ENGINEERS (ASHRAE)

1993 ASHRAE Handbook Fundamentals, Chapters 11, 13, and 19

Available from: ASHRAE
1791 Tullie Circle, NE
Atlanta, GA 30329-5478 Tel. (404) 636-8400

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 13
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 CHEMICAL RUBBER COMPANY (CRC)

Handbook of Chemistry and Physics, 75th Edition (1994-1995), Chapter 6: Fluid properties,
6.1 Thermodynamic properties of air
Available from: CRC
CRC Press
2000 Corporate Blvd. Northwest
Boca Raton, FL 33431 Tel. (407) 994-0555

MISCELLANEOUS

Compressed Air and Gas Handbook, Fifth Edition, 1989; Published by Prentice-Hall, Inc.
Compressed Gas Association, Inc., Chapter 3, Methods of Producing Compressed Air for
Human Respiration.
Considine, D.M., Handbook of Applied Instrumentation, 1982; McGraw-Hill Book Company.
Hankison, Paul M., Theory and Filtering Technique for Compressed Air Instruments,
November 1953.
Hehn, A.H., “Can Component Failures in Air and Oil Systems be Predicted?” Hydraulics and
Pneumatics, July 1971.
Lapple, C.E., “Characteristics of Particles and Particle Dispersoids,” Stanford Research Institute
Journal, 1961; Stanford Research Institute, Palo Alto, CA.
Queer, Elmer R. & McLaughlin, E.R., Desiccation of Air for Air Control Instruments,
Pennsylvania State University Press, State College, PA.
Talbott, E.M., Compressed Air Systems, Volume 2: A Guidebook on Energy and Cost Savings,
1993; Fairmont Press, Inc., 700 Indian Trail, Lilburn, GA 30247.
Weiner, Arnold L., “How to Clean and Dry Compressed Air,” Hydrocarbon Processing,
February 1966; CGA Publishing, Arlington, VA.

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

NFPA, Document No. 70, Chapter 5

Available from: NFPA
P. O. Box 9101
One Batterymarch Park
Quincy, MA 02269-9101 Tel. (617) 770-3000
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

14
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 SOCIETY OF AUTOMOTIVE ENGINEERS, INTERNATIONAL (SAE)

ARP-1156 Requisites for Design Specifications for Absorptive Systems,

1969 (Revised 1992)
Available from: SAE International
400 Commonwealth Drive
Warrendale, PA 15096-0001 Tel. (412) 776-4841

UNITED STATES NUCLEAR REGULATORY COMMISSION (U. S. NRC)

NRC Information Notice

95-53 Failures of Main Steam Isolation Valves as a Result of Sticking
Solenoid Pilot Valves, December 1, 1995
This notice is available on the World Wide Web @URL:
http:/www.nrc.gov/
NUREG 1275 Volume 2 Air Systems Problems in U.S. Light Water Reactors, 1987
Available from: U.S. NRC
11555 Rockville Pike
Rockville, MD 20852 Tel. (301) 492-7000
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996 Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 15
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Annex B — Equipment and application guidelines for producing
instrument air

NOTE — This annex is for information purposes only and is not part of ISA-7.0.01.

B.1 Instrument air system design

An instrument air supply and conditioning system consists of components required to provide an
adequate volume of instrument quality air at the desired pressure.

B.1.1 Instrument air supply system

Typical components of the air supply system (see Figures B-1, B-2, & B-3) include the following:
Filters Aftercoolers and moisture separators
Compressors Pressure regulators
Air treatment systems Pressure-relief devices
Air receivers Piping
Drain traps

B.1.1.1 Intake filters

A dry cartridge intake filter should be provided for the compressor in accordance with the
manufacturer's recommendations. Filters should be located so they are readily accessible for
maintenance.

B.1.1.2 Compressor
Compressors should be sized to deliver air at the specified pressure under all conditions, plus a
margin for future demand and leakage.
Various types of compressors are available including the following:
a) Reciprocating oiled piston
b) Reciprocating oil-less piston
c) Rotary vane
d) Rotary liquid ring
e) Diaphragm
f) Rotary screw
g) Centrifugal
Some compressors are lubricated internally by water, or by water with small amounts of soap or
oil. Compressors identified as "unlubricated" do use lubrication for the bearings and working
parts of the compressor, but the compressor chamber or cylinder is not lubricated because the
plastic or other low friction seals used on the piston eliminate the need for lubricating the cylinder
walls. The "diaphragm-type" compressor likewise is considered as being unlubricated because

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 17
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 the compression chamber is separated from the lubricated portions of the compressor by a
diaphragm.
Some compressors are identified as "oil-free" even though the compressor is internally oil
lubricated because filters are used. Filter limitations can allow lubricant carryover; therefore,
"unlubricated" compressors are recommended.
Although not recommended, if lubricated compressors are used, lubricant removal is required to
avoid the damaging effects on air system components and end-use devices. Provisions should
be made to recover lubricants for disposal in accordance with national and local environmental
requirements.
If synthetic oil is used to lubricate compressors, compatibility should be evaluated for end-use
devices. For example, effects of ester vapor released by synthetic oil can cause elastomeric
damage to end-use devices.

B.1.1.3 Aftercooler and moisture separator

The aftercooler is a heat exchanger that cools the hot compressor discharge air below its dew
point. The condensate is collected in a mechanical separator, which can remove 70 to 80
percent of the moisture and some particulate. Moisture is typically drained by an automatic drain
valve with a manual bypass or drip leg. This moisture should be removed from the air system to
prevent equipment damage downstream.
Water-cooled aftercoolers are usually sized to cool outlet air to within 5°C (approximate) to 8°C
(9°F to 15°F) of the inlet cooling water temperature.
Air-cooled aftercoolers are usually sized to cool outlet air to within 14°C to 17°C (25°F to 31°F) of
the ambient air temperature.

B.1.1.4 Air receiver

Air receivers should be sized to provide an adequate volume of air surge and allow for future
growth. The air receiver surge time can be calculated by using the methodology found in the
Compressed Air and Gas Handbook (see Annex A). A pressure-relieving device should be
installed as required by applicable local and national codes.
The receiver ambient temperature is typically lower than the dew point temperature of the air
entering the receiver. This causes moisture to condense inside the receiver. To help prevent
condensate and particulate intrusion, the outlet line should be located near the top of the receiver
and above the inlet line.
An automatic drain with a manual bypass should be located near the bottom of an air receiver to
dispose of the condensate. Drains on a receiver are susceptible to plugging; therefore an ability
to clean the lines should be provided.

B.1.1.5 Drain traps

Automatic drain traps with manual bypasses should be located on receivers, air line driplegs,
intercoolers, and aftercooler separator drains, as previously mentioned.
Trap failure indications such as level gauges, sight glasses, or alarms are recommended.

B.1.1.6 Air treatment systems

An instrument air treatment system consists of a prefilter, an air dryer, and an afterfilter.

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

18
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 B.1.1.6.1 Prefilter
Coalescing prefilters are required to limit liquids, oil, and water (in aerosol form) from entering the
air dryers. An automatic drain with manual bypass is recommended.

B.1.1.6.2 Air dryer

The air drying equipment should meet the dew point requirements of this standard. Refer to 5.1.
Various types of dryers are available to remove moisture from compressed air. Selecting the
proper type and size of dryer should be based on the actual inlet flow conditions under which the

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---
dryer is expected to perform and on the quality of air that is to be produced. Refer to Table B-1
for additional information.
Refrigerant dryers have limited applications due to dew point restrictions. If design application
allows use of a refrigerant dryer, continuous monitoring is strongly recommended. (See
Table B-1 and Figure C-1.)
The following factors should be considered when selecting dryers:

a) Maximum flow rate: m3/s (m3/h, SCFM)*

b) Maximum inlet temperature: °C (°F)
c) Maximum percentage moisture saturation of inlet (if unknown, assume inlet temperature
at pressure dew point)
d) Minimum inlet pressure: kPa (psig)
e) Maximum inlet pressure: kPa (psig)
f) Maximum allowable outlet dew point temperature at dryer outlet pressure: °C (°F)
g) Required accessories (e.g., pressure gages, relief valves, thermometers, timers, safety
switches.
h) Other pertinent information, such as: contaminants that may be present (oil, liquid, etc.)
i) Utilities available, such as: electricity, steam, water, and control power
j) Electrical area classification where equipment is to be installed.
See the Compressed Air and Gas Handbook Reference in Annex A for additional information.

B.1.1.6.3 Afterfilter
Afterfilters provide final cleaning of the airstream by removing particulate matter from the dryer
discharge. Afterfilters should be specified by absolute particle size. Afterfilters are
recommended on all instrument air systems and should be provided for desiccant dryers to
prevent desiccant dust from passing downstream. Heat reactivated dryers require high
temperature afterfilters. For refrigerated dryers, coalescing filters are recommended.

B.1.1.7 Pressure regulators

Pressure regulators are provided to control the pressure to downstream devices. Pressure
regulator sizing and settings should be chosen such that each end-use device receives an
adequate air supply.
Design review and installation of pressure-relieving devices should be considered, since
pressure regulator failure will result in full system pressure on downstream system devices.

*SCFM = Standard Cubic Feet per Minute

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 19
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`--- Table B.1 — Typical compressed air dryer types(1)
1) Regenerative desiccant dryers

A. Regeneration with Heaters(5)

Flow Range:(2) 0 - 16,990 m3/h @ 38°C at 690 kPa
(0 - 50,000 SCFM @ 100°F at 100 psig)
Outlet Dew Point Range at Line Pressure:(4) -40°C
(-40°F)
Utility Requirements: Electricity or Steam
B. Regeneration without Heaters
Flow Range:(2) 0 - 16,990 m3/h @ 38°C & 690 kPa
(0 - 10,000 SCFM @ 100°F at 100 psig)
Outlet Dew Point Range at Line Pressure:(4) -40°C
(-40°F)
Utility Requirements: Dry Compressed Air

2) Heat of compression dryers(5)

A. Flow Range:(2) 0 - 17,000 m3/h @ 84°C at 690 kPa

(0 - 10,000 SCFM @ 300°F at 100 psig)
Outlet Dew Point Range at Line Pressure:(3) -18°C to 4°C
(0°F to 40°F)
Utility Requirements: Hot Air and Electricity
3) Refrigerant

A. Flow Range:(2) 0 - 8,500 m3/h @ 38°C & 690 kPa

(0 - 5,000 SCFM @ 100°F at 100 psig)
Outlet Dew Point Range at Line Pressure:(3) 2°C to 4°C
(35°F to 39°F)
Utility Requirements: Electricity

B. Flow Range:(2) 8,500 - 16,990 m3/h @ 38°C & 690 kPa

(5,000 - 10,000 SCFM @ 100°F at 100 psig)
Outlet Dew Point Range at Line Pressure:(3) 10°C
(50°F)
Utility Requirements: Electricity
NOTES
(1) The stated values are typical values only and may vary depending on manufacturer.
(2) Flow values are given at standard conditions; e.g., 16°C (60°F) and 101 kPa (14.7 psig).
(3) This dew point may be inadequate for many instrument air system applications. Refer to 5.1 for dew
point requirements. (See ANSI/B93.45M 1982.)
(4) Traditionally, regenerative desiccant dryers for instrument air systems are sized to provide -40°C
(-40°F) dew point air at pressure. However, in extremely cold climates, instrument air applications
may require dew points as low as -73°C (-100°F) at operating pressure.
(5) Heat regenerated dryers are not recommended for use with lubricated compressors.

Copyright The Instrumentation, Systems, and Automation Society 20 ANSI/ISA-7.0.01-1996

Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Figure B.1 — Compressed air-drying system: desiccant dryer

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 21
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Figure B.2 — Compressed air-drying system: refrigerant dryer (air cooled)

22
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Figure B.3 — Compressed air-drying system: refrigerant dryer (water cooled)

Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996 Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 23
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 B.1.1.8 Pressure relief devices
Pressure relief devices should be installed in accordance with applicable codes and to protect
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

devices from potential over-pressurization. Pressure relief devices may include self-relieving
pressure regulators, rupture discs, and relief valves. Check valves should be located and
oriented, so they do not defeat the intended operation of the relief valves.
Relief valve settings should be high enough to avoid continuous lifting. The relief device setting
should not exceed the design pressure rating of any device it protects.

B.1.1.9 Piping
Air distribution systems should be designed in accordance with local, national, and international
codes and standards. Air distribution systems should be designed to ensure that all end-use
devices receive adequate air supply to ensure their satisfactory operation.

B.1.1.9.1 Discharge piping

Piping between the compressor and the aftercooler, and the aftercooler separator and the air
receiver, is considered to be discharge piping. This portion of the air system up to the air dryer
will experience high moisture and high temperature variations. Corrosion-resistant pipe is
recommended in systems using oil-free compressors. Unlike a lubricated compressor system,
the piping lacks the oil film that protects the piping.
The corrosive effects are accelerated by the warm, moist air; vibration; pulsation; and
temperature variations as compressors load and unload. The corrosion by-products lead to
plugged lines, filters, and traps, and an increased corrosion rate can lead to premature wall
failure. When using carbon steel, an increased corrosion allowance should be used in
calculating wall thickness for piping, valves, and vessels.

B.1.1.9.2 Branch connections

The minimum pipe size for horizontal piping should not be less than 25 mm (1 inch) NPS*, except
when six-foot centered, horizontal piping supports are maintained, the minimum pipe size may be
reduced to 15 mm (½ inch) NPS. All branch takeoffs should be from the top of any horizontal
piping header. A typical instrument air supply and branch piping arrangement is shown in API
550 (see Annex A).

B.1.1.10 Manual valves

The effects of moisture, lubricants, and particle contaminants on a valve's internals should be
considered. Flow rate and pressure drop should be considered when selecting the proper type
of valve to use in each application. Valves should be installed per manufacturer's
recommendations and should be accessible for operation and maintenance.
Three basic types of valves are used commonly in instrument air distribution systems: globe,
gate, and ball. Some advantages and disadvantages of each valve type are listed in B.1.1.10.1
through B.1.1.10.3.

B.1.1.10.1 Globe valves

Advantages of globe valves are that they provide the capabilities to regulate system flow rates
and to provide tight shut-off. Globe valves with a dial pointer or stem scales can be used to
provide repeatable settings in a manual control mode.

*National Piping Size

Copyright The Instrumentation, Systems, and Automation Society 24 ANSI/ISA-7.0.01-1996

Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Disadvantages of globe valves are that they reduce flow rate, increase pressure loss, and allow
places for particulates to collect (which can cause valve leakage).

B.1.1.10.2 Gate valves

Advantages of gate valves are that they provide a full, line-size port for air flow with minimal
pressure drop and are conducive to internal cleaning. Gate valves typically are used for on/off
isolation.

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---
Disadvantages of gate valves are that they provide places for particulates to collect in their disc
guides, and the valve discs have been known to separate from their stems. Gate valves should
not be used for throttling.

B.1.1.10.3 Ball valves

Advantages of ball valves are that they provide a full, line-size port for air flow, with minimal
pressure drop, and are conducive to internal cleaning. Ball valves typically are used for on/off
isolation. Another advantage of ball valves is that they provide better shutoff than gate valves
due to their elastomeric ball seal design.
Disadvantages of ball valves are that they are more expensive than comparably-sized globe or
gate valves, and their sealing surfaces are susceptible to leakage from particulate scoring.

B.1.1.11 Valve location and installation

The following should be considered to determine valve location and orientation:
a) Valves should be accessible from grade level or from personnel platforms.
b) Valves required to isolate or bypass a component should be located as close to the
component as practical.
c) When globe or gate valves are used, rising-stem construction provides visual valve
position.
d) Valve orientation should be per the manufacturer's recommendations.

B.2 Air quality considerations

B.2.1 Dew point

ISA-7.0.01 establishes a maximum pressure dew point to protect instrument air systems from the
presence of moisture.
Compression and cooling stages in an instrument air system cause condensation. Compression
increases the partial pressure of the water vapor present. If the water vapor partial pressure is
increased to the saturation water vapor pressure, condensation occurs. Cooling reduces the
saturation water vapor pressure, a temperature-dependent variable. If the saturation water vapor
pressure is reduced to the partial pressure of the water vapor present, water or ice will result.
Therefore, moisture removal is a major consideration of instrument air treatment systems.
The most common methods of moisture removal are compression cooling, absorption, chemical
methods, mechanical separation, and combinations of these methods. See Figures B-1, B-2,
and B-3.

B.2.2 Oil contamination

ISA-7.0.01 establishes an upper limit for oil contamination in instrument air systems.

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 25
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 If the upper limit is exceeded, special adsorption or collection equipment is required to remove oil
in the liquid or vapor state to minimize pneumatic end-user problems ranging from inaccuracies
to failure. Oil in the system can affect system dew point and desiccant life and can create a
potential fire hazard with use of heat reactivated desiccant dryers. Oil contamination of
instrument air systems can result in end-use device failures. For example, the oil can form a
varnish-like substance on hot surfaces, preventing proper component operation. (See
NUREG 1275, Volume 2.)
Using auto oilers in nuclear facilities is strongly discouraged since operating experience has
shown auto oilers to introduce oil contamination, which has resulted in component failures.
Other industries should evaluate specific applications to determine if using auto oilers is
acceptable.*

B.2.3 Particulate (particle size)

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---
Filters should be used to remove particulate from the instrument air system. The afterfilters
should meet the desiccant dryer's manufacturer's recommended micrometer ratings to prevent
desiccant carryover. Particulate can cause equipment malfunction by clogging and eroding small
orifices and working parts in pneumatic instruments and controls.
Each point-of-use filter shall be sized in accordance with the pressure and flow rate requirements
for the end-use device.
Particulate matter can be introduced into an instrument air system from a variety of sources;
such as ambient air through the intake filter and the formation of rust particles, oxide, scale, and
desiccant dust, which can be carried over from the air drying equipment.

B.2.4 Other contaminants

The compressor intake shall be located in an area free from potential air contamination. The
area shall be free from toxic and corrosive vapors, flammable gases and vapors, combustible
dust, and ignitible fibers. The air intake shall not be located in a hazardous (classified) location
as defined by National Fire Protection Association (NFPA) 70, the National Electrical Code,
Chapter 5, Article 500 — Hazardous (Classified) Locations. See reference to NFPA in Annex A.
Unless the air intake can be located in an area that is free of contaminants, an appropriate
scrubber or absorber may be required for the protection of the pneumatic devices. The range of
possible contaminants is so wide that each installation must be considered individually. The kind
and concentration of contaminant, the air dryness, and the amount of compression are all factors
for consideration.
Any cross connections or process connections to the instrument air piping should be isolated
and/or filtered to prevent contamination of the instrument air system.
Contaminants can originate from the system components, such as corrosive vapors generated
from the phosphate esters used in fireproofing synthetic lubricants for compressors. Materials
used for seals and diaphragms in pneumatic devices should be compatible with any synthetic
lubricant used, or an appropriate scrubber should be used in the air system to remove
contaminants.

*For details on why the use of automatic oilers is strongly discouraged, read the United States Nuclear
Regulatory Commission Inspection Report IN 95-53 (refer to Annex A). Some cylinder-type actuators
recommend a lubricant. If an in-line automatic oiler is used in such a case, the location of the oiler must be
selected to minimize the amount of the air system exposed to the lubricant. Also, the other control devices
exposed to the lubricant must be of compatible material. The typical installation for an automatic oiler is at
the point of use. Often the oiler is an integral part of an actuator assembly.

26
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 B.3 Instrument air supply pressure and pneumatic pressure transmission signal

See Table B-2 for Instrument air supply pressures, spans, and ranges.

B.3.1 Line pressure

Nominal instrument air line pressure for the utility industry should be 690 kPa (approximate)
(100 psi). For other industries, nominal instrument line pressure will vary based on specific
applications.

B.3.2 Supply pressure

Nominal supply pressure may vary between 0 kPa and 690 kPa (approximate) (100 psi) to meet
the requirements of the end-use device.

B.3.3 Pneumatic transmission signals

Pneumatic transmission signals are used in process measurement and control systems to
transmit information between components. Pneumatic transmission signals are used for
a) pneumatic controllers;
b) pneumatic transmitters and information transmission systems;
c) current-to-pressure (I/P) transducers;
d) valve positioners; and
e) pneumatic control loops.
Refer to Table B-2 for spans, ranges, and supply pressures.

Table B.2 — Typical spans, ranges, and supply pressures

SI Units (kPa) English Units (psi)

Supply Pressure Supply Pressure

Span Range Span Range
Min. Max. Min. Max.
80 20-100 130 150 12 3-15 19 22
140 35-175 230 260 20 5-25 33 38
160 40-200 260 300 24 6-30 38 44
170 20-190 205 240 24 3-27 30 35

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

ANSI/ISA-7.0.01-1996
Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 27
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 Annex C — Guideline for testing pneumatic systems

NOTE — This annex is for information purposes only and is not part of ISA-7.0.01.

The permissible leakage tolerance in a pneumatic system cannot be critically defined. These
pneumatic systems vary in characteristics; some are more tolerant of leaks than others.
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Current methods of testing vary widely in

a) test pressures;
b) static or cycling pressure; and
c) time duration of holding test pressures.
Pneumatic system design should minimize the number of probable leakage sources.

C.1 Application

A pneumatic system pressure test may be used for the following:

a) To establish initial system integrity
b) To guide trouble-shooting activities
c) To re-establish system integrity after modification
d) To confirm system integrity after maintenance

C.2 Inspections and testing

C.2.1 Initial inspection

Confirm that the name plate data is consistent with the system design criteria; e.g., pressure,
capacity, and temperature.

C.2.2 Verification of air path

Verify the air path from the air supply valve to the air-operated device by performing the following
steps:
a) Isolate the air supply to the air-operated device
b) Disconnect the air line at the air-operated device
c) Set the instrument to deliver air to the air-operated device
d) Observe air flows from the disconnected line at the air-operated device

Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996 Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 29
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 C.2.3 Pressure tests
Pressure testing should be performed after initial system or component installation, maintenance,
and/or modification to verify the following:
a) Component and/or system operability and integrity at design pressure, for initial testing
b) Component and/or system operability at operating pressure, for in-service testing
c) System integrity
Technicians can use a bubble fluid, ultrasonic probe, or tracer gas-measuring device
(electronic or infrared) to observe indication of leakage.

C.3 Tests

It is necessary to test for dew point, lubricants, particles, and other contaminates. Tests or
analysis must be conducted on initial start-up and periodically thereafter. However, continuous
monitoring for dew point is strongly recommended.
It is necessary to monitor performance of individual system devices because improper use or
malfunction can adversely affect system performance. For example, high dew point can result in
component malfunction and system degradation. Therefore, when high dew point problems
occur, action should be taken to lower dew point within limits. Continuous dew point monitoring
provides early detection and/or warning to help prevent high moisture content (see Figure C-1).

C.3.1 Dew point tests

A maximum allowable dew point should be established. A continuous monitoring alarm system
is recommended; however, periodic checks should be scheduled to help ensure delivery of
instrument quality air to end-use devices.
Various methods are available for determining moisture content. These methods include, but are
not limited to, dew point instruments: dewcup, chilled mirror, cloud chamber, hygroscopic salts,
electrical hygrometers, psychrometers, capacitance, spectroscopy, and thermal conductivity.
The dew point temperature value should be expressed at line pressure. If the determination is
made at other than the line pressure, the measured value and the pressure of measurement also
should be noted.

C.3.2 Lubricant content tests

The maximum lubricant content should be as close to zero as possible, and under no
circumstances shall it exceed one (1) ppm w/w or v/v. Any lubricant in the compressed air
system should be evaluated for compatibility with the end-use device. When using a lubricated
compressor, oil contamination is likely.
Periodic checks and routine filter maintenance are required to ensure air quality.
Various methods are available for determining the lubricant content. These methods include, but
are not limited to, microscopic techniques, infrared spectrometry, and ultraviolet molecular
emission for liquids. Gas chromatography can be used for vapors.

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

30
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 9000

8000 1 ATMOSPHERE

7000

6000
--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

5000

2 ATMOSPHERE
4000

3000

2000

3 ATMOSPHERE
1000

0
0 20 40

DEWPOINT ( oF)

Figure C.1 — Moisture content of air vs. dewpoint

Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996 Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004 31
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 C.3.3 Particle size tests
A maximum 40 micrometer particle size in the instrument air stream is acceptable for the majority
of pneumatic devices. Pneumatic devices that require instrument air with less than
40 micrometer particle sizes shall be provided with additional filtration to meet the particulate size
limit for the device.
Periodic checks for particulate matter are strongly recommended, especially if operating
problems are prevalent. Microscopic techniques normally are required for determining particle
size. Various methods are available for determining particle content. These methods include,
but are not limited to, laser analyzers.

C.3.4 Other contamination tests

The instrument air should be free of corrosive contaminants and hazardous gases, which may be
drawn into the instrument air system. The air system intake should be monitored as applicable
for contaminants. If contamination exists in the compressor intake area, the air should be taken
from a different elevation or a remote location free from contamination (see B.2.4 for details).
Examples of contamination sources are as follows:
a) Painting
b) Chemical cleaning
c) Engine exhaust

--```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

32
Copyright The Instrumentation, Systems, and Automation Society ANSI/ISA-7.0.01-1996
Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.
 --```,,,`,`,,```,`,,,,`,,``,,-`-`,,`,,`,`,,`---

Developing and promulgating technically sound consensus standards,

recommended practices, and technical reports is one of ISA's primary
goals. To achieve this goal the Standards and Practices Department
relies on the technical expertise and efforts of volunteer committee
members, chairmen, and reviewers.
ISA is an American National Standards Institute (ANSI) accredited
organization. ISA administers United States Technical Advisory
Groups (USTAGs) and provides secretariat support for International
Electrotechnical Commission (IEC) and International Organization for
Standardization (ISO) committees that develop process measurement
and control standards. To obtain additional information on the
Society's standards program, please write:

ISA
Attn: Standards Department
67 Alexander Drive
P.O. Box 12277
Research Triangle Park, NC 27709

ISBN: 1-55617-606-6

Copyright The Instrumentation, Systems, and Automation Society Document provided by IHS Licensee=Transalta Utilities/5910033100, 07/07/2004
Reproduced by IHS under license with ISA 00:19:53 MDT Questions or comments about this message: please call the Document
Policy Group at 303-397-2295.