VAL MANUAL 005 Process Validation of Bulk Drug API and Intermediate Sample
Uploaded by
Vinay PatelVAL MANUAL 005 Process Validation of Bulk Drug API and Intermediate Sample
Uploaded by
Vinay PatelProcess Validation of Bulk Drug (API and Intermediate)
Regulatory Basis:
FDA Quality Systems Regulations
Reference: FDA CFR - Code of Federal Regulations Title 21
1 Purpose
The purpose of this document is to provide guidance on the validation of
processes for the manufacture of bulk drug i.e. those synthetic stages from
introduction of the defined API Starting Materials into the process up to and
including the physical processing of the API (Active Pharmaceutical Ingredient).
Validation should extend to those operations determined to be critical to the
quality and purity of the API. The validation of stages prior to the API Starting
Materials is not mandatory. A risk assessment may deem it necessary.
2 Scope and Applicability
All functions, departments and manufacturing sites or their contractors. The
manufacture of intermediates post API starting materials up to and including
final API, for onward sale external to the site or for use in site formulated products.
3 Definitions
3.1 Process Validation
Establishing documented evidence, which provides a high degree of assurance
that a specific process will consistently produce a product meeting its predetermined
specifications and quality characteristics.
3.2 Validation Protocol
A written plan stating how validation will be conducted and defining acceptance
criteria. For example, the protocol for a manufacturing process identifies processing equipment,
critical process parameters/operating ranges, product characteristics,
sampling, test data to be collected, number of validation runs, and acceptable test results.
Note: for process validation, the protocol would identify the number of validation batches.
3.3 API Starting Material
A raw material, intermediate, or an API that is used in the production of an API
and that is incorporated as a significant structural fragment into the structure of
the API. An API Starting Material can be an article of commerce, a material purchased
from one or more suppliers under contract or commercial agreement, or produced in-house. API
Copyright©www.gmpsop.com. All rights reserved
Unauthorized copying, publishing, transmission and distribution of any part of the content by electronic means are
strictly prohibited. Page 2 of 9
Process Validation of Bulk Drug (API and Intermediate)
The validation of a process for a product that has been marketed based upon
accumulated manufacturing, testing and control batch data. It may be used as the
basis to support (but not in lieu of) prospective/concurrent validation activities.
5.2.4 Prior to Commercial Process
Process validation activities during product development are the responsibility of
the development function. Development reports provide a repository of product
knowledge that the processing and testing are understood. In addition they help
in setting process parameters by providing information on worst case testing
carried out on small-scale laboratory batches.
5.2.5 Commercial Process
It is the responsibility of the manufacturing site to ensure that all manufacturing
processes used for commercial materials are validated. Prospective validation,
follows a pre-prepared validation protocol that derives any critical parameters
/activities and acceptance criteria from the product development/scale up/optimization
experiences for new products, and/or from historical manufacturing information
on existing processes. Validation should be undertaken under the fixed process
conditions to be used for routine manufacture using appropriately trained individuals.
5.3 New and Modified Products and Processes
For new or modified product or processes, it is now frequent practice to derive
parameter ranges from Factorial Experimental Design (FED) work in the
laboratory, then to establish the process on the plant using Established Parameter
Ranges (EPR).
There is invariably a period of experimental manufacture on plant, during which
processing conditions may be adjusted until optimization of the process is
achieved. This experimental work should be carried out in accordance with a
program, which should specify the objectives, methods and criteria for
completion of the work.
When all experimental work has been successfully completed and the product or
process can be considered established, it still requires validation to provide
assurance that it satisfies its intended purpose, that is, to consistently yield a
product of the required quality. Validation should be carried out after completion
of the experimental or establishment phase and should normally cover the
manufacture of three consecutive batches nominated in advance.
Minor changes are allowed between establishment and validation but critical
process parameters must remain unchanged.
An example of processing steps normally covered in a validation program are
shown in the table in appendix 1, together with examples of objectives, sampling
& testing and acceptance criteria for each step. This information should be used
only as a guideline, however, and appropriate programs should be produced to
Copyright©www.gmpsop.com. All rights reserved
Unauthorized copying, publishing, transmission and distribution of any part of the content by electronic means are
strictly prohibited. Page 5 of 9
Process Validation of Bulk Drug (API and Intermediate)
Copyright©www.gmpsop.com. All rights reserved
Unauthorized copying, publishing, transmission and distribution of any part of the content by electronic means are strictly
prohibited. Page 8 of 9
