Thank you for choosing our pallet truck.

For your safety and correct operation, please carefully read

the manual before use.

NOTE: All of the information reported herein is based on data available at the time of printing. The
factory reserves the right to modify its own products at any time without notice or incurring in any
sanction. Please verify with the factory for possible updates.

1. GENERAL SPECIFICATIONS

Capacity 2500kg / 5500lbs

Max. Fork Height 200mm / 7.9”
Min. Fork Height 75mm / 2.9”
Fork Length 1220mm /48”
Width Overall Forks 520 or 685mm / 20.5 or 27”
Individual Fork Width 160mm / 6.3”
Load Wheel Diameter Ø 74 x 70mm / 2.9 x 2.75” Nylon, Polyurethane
Steering Wheel Diameter Ø 180 Nylon, Polyurethane, Rubber

Materials and specification are subject to change without notice.

2. TO ATTACH HANDLE TO PUMP UNIT

2.1 Remove 3 bolts (D611) from the handle bracket (D151).
2.2 Set handle (D610A, D610B or D610AS) on the bracket (D151), notice to allow the chain (D612)
and the adjusting bolts (D614) assembly to pass through the hole in the center of the bracket (D151)
and shaft (D153).
2.3 Insert the 3 bolts (D611) through the handle into the bracket (D151), then tighten them securely.
2.4 Raise the lever plat (D132) and insert the adjusting bolt (D614) into the front slot, keeping the
adjusting nut (D615) on the under side of the lever plat (D132).

3. TO ADJUST RELEASE DEVICE

On the draw-bar of this pallet truck, you can find the control handle (D608 or D608S) which can be
regulated in three positions:
Raise - handle down
Drive position - handle in center position
Lower - handle up, the lever moves back the drive position when released.
If however they have been changed, you can adjust according to following step:
3.1 If the forks elevate while pumping in the DRIVE position, turn the adjusting nut (D615) on the
adjusting bolt (D614) or adjusting screw (D133) clockwise until pumping action does not raise the
forks and the DRIVE position functions properly.
3.2 If the forks descend while pumping in the DRIVE position, turn the nut (D615) or adjusting screw
(D133) counter-clockwise until the forks do not lower.
3.3 If the forks do not descent when the control handle (D608 or D608S) is in the LOWER position,
turn the nut (D615) or adjusting screw(D133) clockwise until raising the control handle(D608 or
D608S) lowers the forks. Then check the DRIVE position according to item 3.1 and 3.2 to be sure
the nut (D615) or adjusting screw (D133) is in the proper position.
1
3.4 If the forks do not elevate while pumping in the RAISE position, turn the nut (D615) or adjusting
screw (D133) counter-clockwise until the forks elevate while pumping in the RAISE position. Then
check the LOWER and DRIVE position according to item 3.1, 3.2 and 3.3.

4. MAINTENANCE
Your pallet truck is largely maintenance-free.
4.1 OIL
Please check the oil level every six months. The oil capacity is about 0.3lt. Use the hydraulic type
oil according to temperature scale below.

Temperature Oil
-20℃~+40℃ L-HV46 Hydraulic oil

4.2 HOW TO EXPEL AIR FROM THE PUMP UNIT

The air may come into the hydraulic oil because of transportation or pump in upset position. It can
cause that the forks do not elevate while pumping in the RAISE position. The air can been banished
in the following way: let the control handle (D608 or D608S) on the LOWER position, then move the
handle (D610A, D610B or D610AS) up and down for several times.

4.3 DAILY CHECK AND MAINTENANCE

Daily check of the pallet truck can limit wear as much as possible. Special attention should be paid
to the wheels, the axles, as thread, rags, etc. It may block the wheels. The forks should be
unloaded and lowered in the lowest position when the job is over.

4.4 LUBRICATION
Use motor oil or grease to lubricate all moveable parts.

5. GUIDE TO SAFETY OPERATION

For safe operation of the Hand Pallet Truck, please read all warning signs and instructions
here and on the pallet truck prior to use.

5.1 Do not operate the pallet truck unless you are familiar with it and have been trained or
authorised to do so.
5.2 Do not operate the truck unless you have been trained and authorised. Give special attention to
the wheels, the handle assembly, the forks, and the lower control.
5.3 Do not use the truck on sloping ground.
5.4 Never place any part of your body in the lifting mechanism or under the forks or load. Do not
carry passengers.
5.5 We advise that operators should wear gloves and safety shoes.
5.6 Do not handle unstable or loosely stacked loads.
5.7 Do not overload the truck.
5.8 Always place loads centrally across the forks and not at the end of the forks (See Fig. 2).
5.9 The capacity of the truck assumes an evenly distributed load with the centre of the load being
2
 at the halfway point of the length of the forks.
5.10 Make sure that length of the forks matches the length of the pallet.
5.11 Lower the forks to lowest height when the truck is not being used.
5.12 In other specific conditions the operators should take extra care in operating the truck.

6. TROUBLES SHOOTING
No Trouble CAUSE ACTION
1 The forks can not be - The hydraulic oil is not - Pour in the oil.
up the max height. enough.
- Without hydraulic oil. - Fill in the oil.
- The oil has impurities. - Change the oil.
2 The forks can not be - The nut (D615) is too high or - Adjust the nut (D615) or the screw
lifted up. the screw (D133) is too close, (D133) .(see item 3.4)
keep the pumping valve open.
- Air come into the hydraulic - Banish the air.(see item 4.2)
oil.
- The piston rod (D147) or - Replace the piston rod (D147) or
pump body is deformed pump body.
resulting from partial loading
slanting to one side or
3 The forks can not be over-loading.
descended. - The fork was kept in the high - Keeping the fork in the lowest
position for long time with position if not using, and pay more
piston rod bared to arise in attention to lubricate the rod.
rusting and jamming of the
rod.
- The adjusting nut (D615) or - Adjust the nut (D615) or the screw
the screw (D133) is not in the (D133). (see item 3.3)
correct position.
- Sealing parts worn or - Replace with the new one.
4 Leaks damaged.
- Some part cracked or worn - Replace with the new one.
into small.
- The impurities in the oil - Replace with new oil.
cause the release valve to be
unable to close tight.
- Some parts of hydraulic - Inspect and replace the waste
5 The fork descends system is cracked or bored. parts.
without the release - Air has gotten into the oil. - Banish the air. (See item 4.2)
valve worked.
- Sealing parts worn or - Replace with the new one.
damaged.
- The adjusting nut (D615) or - Adjusting the nut (D615) or the
the screw (D133) is not in the screw (D133). (See item 3.2)
correct position.

*NOTE: DO NOT ATTEMPT TO REPAIR THE PALLET TRUCK UNLESS YOU ARE
TRAINED AND AUTHORIZED TO DO SO.

3
4
 List of Handle
Mobile Mobile
No. Description Qty. Remark No. Description Qty. Remark
Part # Part #
For
D601 ND601 Spring 1 D610A ND610A Handle (Shell) 1
Type B
D602 ND602 Blade Spring 1 D611 ND611 Screw 3
D603 ND603 Roller 1 D612 Chain 1
D604 ND604 Elastic Pin 1 D613 ND1214 Pin 1
D605 ND605 Elastic Pin 1 D614 Adjusting Bolt 1
D606 ND606 Elastic Pin 1 D615 ND615 Adjusting Nut 1
D607 ND607 Elastic Pin 1 D616 ND616 Elastic Washer 3
Control Complete For
D608 ND608 1 D402 ND402 1
Handle Handle Assy. Type B
D609 ND609 Pull Board 1

5
 List of Fork Frame
Mobile Mobile
No. Description Qty. Remark No. Description Qty. Remark
Part # Part #
D201 ND201 Screw 1 D216 ND216 Elastic Pin 2
D202 ND202 Oil - holder 1 D217# ND217# Shaft for Roller 4
D203B ND203B Rock – arm 1 D218 ND218 Fork Frame 1
8 or
D204 ND204 Elastic Pin 1 D219 ND219 Washer
4
Retaining 8 or
D205 ND205 2 D220 ND220 Bearing
Ring 4
Nylon Load Roller
D207 ND207 Shaft 2 D221# ND221NT 4
(Tandem)
Polyurethane Load
D206D ND206D Joint 2 D221# ND221PT 4
ONLY Roller (Tandem)
D208D ND208D Pushing Rod 2 for D222# ND222# Linking Plate 4
Type B 8 or
D209D ND209D Nut 2 D223 ND223 Elastic Pin
2
D210 ND210 Pin 2 D224 ND224 Bushing 4
D211 ND211 Shaft 1 ONLY D225 ND225 Bushing 2
D212 ND212 Shaft 2 for D226 ND226 Bolt 2
D213 ND213 Elastic Pin 2 Type B D227 ND227 Enter Roller 2
D214 ND214 Shaft 2 D228 ND228 Nut 2
Frame of Nylon Load Roller
D215 ND215 2 D229* ND229NS 2
Roller (Single)
Polyurethane Load
D229* ND229PS 2
Roller (Single)
D230* ND230 Shaft for Roller 2
D231 ND231 Washer 2
D232 ND232 Washer 4

(Note # --For Tandem wheel, * --For single wheel)

6
 List of Pump Unit
No. Mobile Part # Description Qty. Remark
D101 ND101 Pump Piston Rod 1
D102 ND102 Washer 1
D103 ND103 Spring 1
D104 ND104 Dust Ring 1
D105 ND105 Y – Seal 1
D108 ND108 Spring 1
7
D109 ND109 Spindle of Pumping Valve 1
D112 ND112 Steel Ball 1
D106 ND106 Screw 1
D107 ND107 O – Ring 1
Only for TYPE A
D110 ND110 Seat of Pumping Valve 1
D111 ND111 O – Ring 1
D106B ND106B Screw 1
D107B ND107B O – Ring 1
D110B ND110B Seat of Pumping Valve 1
Only for TYPE B
D111B ND111B O – Ring 1
D159B ND159B Sleeve 1
D160B ND160B Screw 1
D113 ND113 Base of Pump 1
D115 ND115 Elastic Pin 1
D116 ND116 Steering Wheel 2
D118 ND118 Thrust Plate 1
D119 ND119 Oil – holder 1
D120 ND120 Retaining Ring 1
D121 ND121 Cover of Bearing 1
D122 ND122 Bearing 1
D123 ND123 Elastic Pin 2
D124 ND124 Dust Cover 2
D117 ND117 Shaft of Steering Wheel 1
D125 ND125 Round Nut 2 Only for TYPE C
D126 ND126 Tab Washer 2
D117 ND117 Shaft of Steering Wheel 1
D125 ND125 Round Nut 2 Only for TYPE D
D126 ND126 Tab Washer 2
D127 ND127 Bearing 4
D129 ND129 Spring 1
D130 ND130 Strike Pin 1
D131 ND131 O – Ring 2
D132 ND132 Lever Plat 1
D133 ND133 Adjusting Screw 1
D134 ND134 Nut 1
D135 ND135 O – Ring 1
D136 ND136 Axle Sleeve 1
D137 ND137 Adjusting Bolt 1
D139 ND139 Spindle of Safety Valve 1
D140 ND140 Spring 1
D141 ND141 O – Ring 1
D142 ND142 Screw 1
D143 ND143 O – Ring 1
D144 ND144 Y – Seal 1
D145 ND145 Elastic Pin 1
D146 ND146 Steel Ball 1
D147 ND147 Piston Rod 1
D148 ND148 Dust Ring 1
D149 ND149 Screw 1
D150 ND150 Shaft 1
D151 ND151 Bracket 1
D152 ND152 Pressure Roller 1
D153 ND153 Shaft 1
D154 ND154 Elastic Pin 1
D155 ND155 Elastic Pin 1
D156 ND156 Bushing 1
D157 ND157 Seal Washer 1
D158 ND158 Bushing 2
D405 ND405 Seal Kit 1
D404 ND404 Complete Pump Assembly 1
8