The Next Step in Belting

Food
Flat Belts
Grade
Positive
Food Industry
Drive Line
ConveyingSolutions
Conveying Solutions
SuperDrive™
ITE ITO-50 MC IRT
Impression Impression Mini Impression
Top Embossed Top Oval Cleats Roof Top

The homogeneous Positive Drive, recognized worldwide as the best choice where hygiene and conveying efficiency are essential.
Smooth Top SuperDrive™ Belts
Coefficient Thickness Minimum Pulley Maximum Pull
Product Shore Temperature Diameter Force
of Friction Certifications
& Color Hardness Range on UHMW mm mm Inch kg/cm lbs/in
3 126 431/32 7 39.2
-20°C to 90° C
FHB-SD Blue 16 55D 0.20 4 176 615/16 9 50.40 FDA/USDA/EU
-5°F to 194° F
6 300 1113/16 14 78.40
-20°C to 90°C 3 126 431/32 7 39.2
FHW-SD Off White 55D 0.20 FDA/USDA/EU
-5°F to 194°F 4 176 615/16 9 50.40
-20°C to 90°C 3 126 431/32 7 39.2
FEHB-SD-ITM2 Blue 16 55D 0.18 FDA/USDA/EU
-5°F to 194°F 4 176 615/16 9 50.40
3 80 31/4 6.25 35
-20°C to 70°C
FMB-SD Blue 53D 0.28 4 120 43/4 8 44.80 FDA/USDA/EU
-5°F to 158°F
6 240 93/4 12.50 70
-20°C to 70°C 3 80 31/4 6.25 35
FMW-SD Beige 53D 0.28 FDA/USDA/EU
-5°F to 158°F 4 120 43/4 8 44.80
-20°C to 70°C
FMB-SD Blue 02 53D 0.28 3 80 31/4 6.25 35 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C 3 80 31/4 6.25 35
FEMB-SD-ITM2 Blue 53D 0.22 4 120 43/4 8 44.80 FDA/USDA/EU
-5°F to 158°F
Impression Top SuperDrive™ Belts
-20°C to 90°C 3 126 431/32 7 39.2
FHB-SD-ITO50 Blue 16 55D 0.20 FDA/USDA/EU
-5°F to 194°F 4 176 615/16 9 50.40
-20°C to 90°C
FHB-SD-ITE Blue 16 55D 0.20 3 126 431/32 7 39.2 FDA/USDA/EU
-5°F to 194°F
-20°C to 70°C
FMB-SD-ITO50 Blue 53D 0.28 3 80 31/4 6.25 35 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C
FMB-SD-ITE Blue 53D 0.28 3 80 31/4 6.25 35 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C
FMB-SD-MC Blue 53D 0.28 3 100 4 6.25 35 FDA/USDA/EU
-5°F to 158°F
Hydrolysis & Chemical Resistant SuperDrive™ Belts
-20°C to 70°C 3 100 4 6.5 36.3
FDR-SD-V1 Blue 15 53D 0.28 FDA/USDA/EU
-5°F to 158°F 4 130 51/8 8.6 48.4
FEDR-SD- -20°C to 70°C
Blue 15 53D 0.22 3 100 4 6.5 36.3 FDA/USDA/EU
ITM2-V1 -5°F to 158°F
FEDR-SD- -20°C to 70°C
Blue 15 53D 0.22 3 100 4 5.5 30.7 FDA/USDA/EU
ITO50-V1 -5°F to 158°F
-20°C to 70°C
FDR-SD-IRT-V1 Blue 15 53D 0.22 4 140 51/2 6.5 36.3 FDA/USDA/EU
-5°F to 158°F
Low Temperature (LT) SuperDrive™ Belts
-35°C to 65°C
FMB-SD-LT Blue 15 95A/46D 0.30 3 80 31/4 3 16.80 FDA/EU
-31°F to 149°F
Metal Detectable (MD) SuperDrive™ Belt
-20°C to 60°C
FMB-SD-MD Blue 09 53D 0.28 3 100 4 6 33.6 FDA/EU
-5°F to 140°F
FMB-SD- -20°C to 60°C
Blue 09 53D 0.28 3 100 4 6 33.6 FDA/EU
ITO50-MD -5°F to 140°F

+/- 200mm / 8” +/- 200mm / 8” +/- 100mm / 4”

40mm

Pitch size for reference only SuperDrive™ Drive Pulley SuperDrive™ Tail Pulley SuperDrive™ Support Pulley

www.voltabelting.com
 Food Grade - Positive Drive Line

Mini SuperDrive™
The only trackable Mini Positive Drive product.
The MiniSD™ design is similar to the world leader, Volta SuperDrive™; scaled down for a smaller minimum pulley.Standard belt width:
1524mm/60”or 2032mm/80”. Please contact Volta Belting representative for additional information.

Smooth Top Mini SuperDrive™ Belts

Thickness Minimum Pulley Maximum Pull
Product Shore Temperature Coefficient Diameter* Force**
of Friction Certifications
& Color Hardness Range*** on UHMW mm mm Inch kg/cm lbs/in
-20°C to 70°C
FMB-MSD Blue 95A/46D 0.28 2.5 48 1.89 4 22.4 FDA/USDA/EU
-5°F to 158°F
Impression Top Mini SuperDrive™ Belts
FMB-MSD- -20°C to 70°C
Blue 95A/46D 0.28 2.5 48 1.89 4 22.4 FDA/USDA/EU
ITO50 -5°F to 158°F
-20°C to 70°C
FMB-MSD-MC Blue 95A/46D 0.28 2.5 80 3.15 4 22.4 FDA/USDA/EU
-5°F to 158°F
Note: * Minimum Pulley Diameter – Normal Flex. Dimensions are relevant for an ambient temperature above 0°C / 32°F.
** Maximum Pull Force – in kg/cm width & lb/in width.
***To determine the allowable Pull force, check the “Temperature Correction Factor” table.
Declaration of Conformity in compliance with Food Contact Regulations: EU No.-10/2011 amended by 2017/752, 1935/2004 and 2023/2006
and FDA Art. 21. CFR.177.2600. Compatible with HACCP principles.

M-Material 150mm / 6” 100mm / 4” 50mm / 2”

25.4mm

H-Material
25.4mm

Pitch size for reference only Tail Pulley Drive Pulley Support Pulley

Mini DualDrive™
A scaled-down version of the original DualDrive™ tooth geometry. Standard belt width: 2032mm/80”.
Smooth Top Mini DualDrive™ Belts
Coefficient Thickness Minimum Pulley Maximum Pull
Product Shore Temperature Diameter* Force**
of Friction Certifications
& Color Hardness Range*** on UHMW mm mm Inch kg/cm lbs/in
-20°C to 70°C
FMB-MDD Blue 95A/46D 0.28 2.5 48 1.89 4 22.4 FDA/USDA/EU
-5°F to 158°F
Impression Top Mini DualDrive™ Belts
FMB-MDD- -20°C to 70°C
Blue 95A/46D 0.28 2.5 48 1.89 4 22.4 FDA/USDA/EU
ITO50 -5°F to 158°F

Note: * Minimum Pulley Diameter – Normal Flex. Dimensions are relevant for an ambient temperature above 0°C / 32°F.
** Maximum Pull Force – in kg/cm width & lb/in width.
***To determine the allowable Pull force, check the “Temperature Correction Factor” table. Declaration of Conformity in compliance with Food
Contact Regulations: EU No.-10/2011 amended by 2017/752, 1935/2004 and 2023/2006 and FDA Art. 21. CFR.177.2600. Compatible with HACCP principles.

25.4mm
25mm / 1”

Pitch size for reference only MDD Sprocket MDD Sprocket

Volta Belting Technology Ltd.

DualDrive™
| Minimal retrofitting required. DualDrive™ is suited to some 2”
pitch modular belt sprockets but for both reliability and hygiene
these should be replaced.
| DualDrive™ is a fully extruded Positive Drive belt with drive teeth
running the full width of the belt at a 2” pitch.
Mechanical Benefits:
| Replaces modular systems that require extensive cleaning and
lengthy soaking and wear quickly at the joints.
| Greatly reduced noise levels in comparison with to modular belts.
| Integrated teeth for a Positive Drive with no slippage. IRT
Dr ive™
No pretension of the belt is needed. Dual
|
| Extruded in 30 or 60m (100 or 200ft) length and 1524mm (60”) width.
-5 0
Material Features: alD r i ve ™ ITO
| Smooth or textured homogeneous surface. Du
ace
| Special texture available for non-stick applications. oth Surf
™ Smo
| No ply/fraying of fibers. Drive
Dual
| Easy and effective cleaning.
| No cracks or crevices that can potentially harbor bacteria.

Smooth Top DualDrive™ Belts

Thickness Minimum Pulley Maximum Pull
Product Shore Temperature Coefficient Diameter Force
of Friction Certifications
& Color Hardness Range on UHMW mm mm Inch kg/cm lbs/in
-20°C to 90°C
FHB-DD Blue 16 55D 0.20 3 126 431/32 7 39.2 FDA/USDA/EU
-5°F to 194°F
-20°C to 70°C
FMB-DD Blue 02 53D 0.28 3 80 31/4 6 33.6 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C 3 80 31/4 6 33.6
FMB-DD Blue 53D 0.28 FDA/USDA/EU
-5°F to 158°F 4 120 43/4 7.7 43
-20°C to 70°C
FMB-DD-ITM2 Blue 53D 0.28 3 80 31/4 6 33.6 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C
FMW-DD Beige 53D 0.28 3 80 31/4 6 33.6 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C
FMW-DD-ITM2 Beige 53D 0.28 3 80 31/4 6 33.6 FDA/USDA/EU
-5°F to 158°F
Impression Top DualDrive™ Belts
-20°C to 70°C
FMB-DD-ITO50 Blue 53D 0.28 3 80 31/4 6 33.6 FDA/USDA/EU
-5°F to 158°F
-20°C to 70°C
FMB-DD-IRT Blue 53D 0.28 4 100 4 6 33.6 FDA/USDA/EU
-5°F to 158°F
Hydrolysis & Chemical Resistant DualDrive™ Belts
-20°C to 70°C
FDR-DD-V1 Blue 15 53D 0.28 3 100 4 6.5 36.3 FDA/USDA/EU
-5°F to 158°F
FDR-DD- -20°C to 70°C
Blue 15 53D 0.28 3 100 4 6.5 36.3 FDA/USDA/EU
ITM2-V1 -5°F to 158°F
Low Temperature (LT) DualDrive™ Bel
-35°C to 65°C
FMB-DD-LT Blue 15 95A/46D 0.30 3 80 31/4 3 16.80
-31°F to 149°F
Metal Detectable (MD) DualDrive™ Belt
-20°C to 60°C
FMB-DD-MD Blue 09 53D 0.28 3 100 4 6 33.6 FDA/EU
-5°F to 140°F

50mm 38mm/1½" 38mm/1½" 38mm/1½" 38mm/1½"

Pitch size for reference only Machined Drive Machined Drive Molded Drive Molded Tail Roller
Sprockets Sprockets Sprocket
www.voltabelting.com
 Food Grade - Positive Drive Line

Volta RoundFlex™ Lace

New, improved geometry for a better grip on pulleys. Compatible with Volta MB,MW,MB-MD and DR material
Flat and Positive Drive belts including MSD & MDD belts from 2.5 to 5mm thickness.
All Volta belt materials are easy to clean without removing from conveyor and therefore we only recommend
lace when absolutely necessary. The strength of the belt will be affected at the joint where lace is used.

RoundFlex™ Lace

RoundFlex™ Lace

We are committed to providing a complete package focusing on

servicing our customers all the way, up until the belts are safely
installed and the conveyor is running smoothly.

Volta Belting Technology Ltd.

Fabrications on Positive Drive Belts

Perforated SuperDrive™ SuperDrive™ Trough Conveyor with Perforated Mini DualDrive™ Belt
with Spaced Flights Chevron Flights

Mini SuperDrive™ Belt Perforated DD-IRT Belt SuperDrive™ Z-elevator with Flights, 
Guides and Sidewalls

DualDrive™ with Impression Top IRT SuperDrive™ with Flights Working SuperDrive™ with Sidewalls 
Flights & Guides under Water and Special Flights

CORPORATE USA EUROPE

HEADQUARTERS Tel. +1 830 229 2384 Tel. +31 546 580166
Sales and Manufacturing [email protected] [email protected]
[email protected]

Volta Belting makes no warranty with respect to any of its products Copyright© Volta Belting Technology Ltd.
www.voltabelting.com for a particular purpose. S
 ee Volta General Terms and Conditions.  CAT501EN00. Ver.Z - January.2024