0% found this document useful (0 votes)
61 views1 page

Ekoled Instrukcijos Juostos ENG

The document provides instructions for operating LED strip lights, including technical specifications, installation instructions, and safety guidelines. It details how to correctly connect and install single-color and RGB LED strips, including recommended power supplies and controllers. Cutting marks and polarity are also indicated.

Uploaded by

samer.almia
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
61 views1 page

Ekoled Instrukcijos Juostos ENG

The document provides instructions for operating LED strip lights, including technical specifications, installation instructions, and safety guidelines. It details how to correctly connect and install single-color and RGB LED strips, including recommended power supplies and controllers. Cutting marks and polarity are also indicated.

Uploaded by

samer.almia
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

LED strip operating instruction

Before using the product read the entire installation manual.


Because only correctly connected and properly used equipment can operate safely and reliably long.
Technical characteristics:

Power 4,8W 7,2W 9,6W 12W 14,4W


Length in the roll 5m
60 LED/m, 30 LED/m, 120 LED/m, 60 LED/m 60 LED/m,
LED quantity, type
SMD3528 SMD5050 SMD3528 SMD2835 SMD5050
Luminous 300 Lm/m 360 Lm/m 600 Lm/m 1200 Lm/m 720 Lm/m
Color 3200K (warm white)/6000K (cold white)/RGB
Voltage DC 12 V
Beam angle 120°
IP rating IP 20/IP 65/IP 68
Every 3 diodes cut only scissors symbol market locations. If there is not such
market, cut contacts intersection location only.
Way of cutting

Lifetime 30 000 hours.


Temperature range from -20 C to +40 C
width 8 mm (10 width 10 mm (12
mm with mm with width 11 mm (13 mm with silicone)/height 3 mm
Dimensions
silicone)/height silicone)/height 4
3 mm mm

LED strips using:


• The strip can be cut every 3 diodes (LEDs), on scissors symbol market locations.
• The strip allocates the heat after connecting the system to the network. So stick to the aluminum profile.
Cooling for the strip 14,4W is necessary!
• Bending angle must be not less 90° in avoidance of damage of hermetic layer.
• Only fully installed LED strips chain can be connect to the network. LED strip installation

For LED one color strip connection are necessary:


•Power supply 12V DC of suitable power;
Suitable power of power supply = length of strip x power of 1m strip + 20%
• The additional power supply for connecting more than 5m LED strip.
• Connectors of strip

For RGB strip connection are necessary:


• Power supply 12V DC of suitable power;
• RGB controller;
• Signals amplifier and power supply for it (for connecting more than 5m LED strip);
*RGB installation
• Connectors of strip.

Instruction of installation:
• Clear the working surface from dirt and grease;
• Remove the protective layer of the adhesive tape;
• Stick the tape to the surface;
• Connect LED strip (check connection scheme).

Marking of LED strip:


„+” „12V+“– positive pole of power supply.
„-“„12V-“– negative pole of power supply.
„R“„G“„B“– R - red, G - green, B - blue.

*R G B colors of LED strip - „R“ „G“ „B“ are „-“ and „+” is „12V+“ – the positive pole of power supply .

Valid from 2014 11 06

You might also like