ABSTRACT OF COST

Name of the work : DSR - 2023 IN MS EXCEL

S.H. No. Description of Sub-Head Amount (Rs)

01. Earth Work : 76358.00

02. Concrete Work : 480106.00
03. Reinforced Cement Concrete : 839767.00
04. Masonry Work : 390279.00
05. Stone Work : 2195632.00
06. Cladding Work : 454453.00
07. Wood and P.V.C. Work : 1941900.00
08. Steel Work : 56882.00
09. Flooring : 242519.00
10. Roofing : 115861.00
11. Finishing : 35009.00
12. Repairs to Buildings : 693389.00
13. Dismantling and Demolishing : 82595.00
14. Road Work : 382465.00
15. Sanitary Installations : 535787.00
16. Water Supply : 1952347.00
17. Drainage : 820929.00
18. Pile Work : 655287.00
19. Aluminium Work : 36680.00
20. Water Proofing : 54919.00
21. Rain Water Harvesting and Tube Well : 51686.00
22. Conservation of Heritage Buildings : 1886.00
23. Structural Glazing and Aluminium Co : 25428.00
24. New Technologies and Materials : 358756.00
Total : : 12480920.00 ###
Add GST @ 18.00% on (A) : 2246566.00
Add contingencies @ 5% on (A) : 624046.00
Grand Total 15351532.00

Say Rs. 1,53,51,600/-

Junior Telecom Officer (Civil) Sub-Divisional Engineer (Civil)

BSNL Civil Sub-Division BSNL Civil Sub-Division
NALGONDA NALGONDA

Estimate prepared with Jalli's App - 2023 (Civil) :: Estimate Code :DSR_23
 Executive Engineer (Civil)
BSNL Civil Dn-I
HYDERABAD

Estimate prepared with Jalli's App - 2023 (Civil) :: Estimate Code :DSR_23
 DSR-2023 IN MS EXCEL (Dated 04.11.2023)

I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)

Sub-Head : Earth Work
2.1 Earth work in surface excavation not exceeding 30 cm
in depth but exceeding 1.5 m in width as well as 10 sqm
on plan including getting out and disposal of excavated
earth upto 50 m and lift up to 1.5 m, as directed by
Engineer-in-Charge:

2.1.1 All kinds of soil 1.00 Sqm 129.85 One Square 130.00
Metre
2.2 Earth work by mechinical / manual means in rough
excavation, banking excavated earth in layers not
exceeding 20cm in depth, breaking clods, watering,
rolling each layer with 1/2 tonne roller or wooden or
steel rammers, and rolling every 3rd and top-most layer
with power roller of minimum 8 tonnes and dressing up
in embankments for roads, flood banks, marginal banks
and guide banks or filling up ground depressions, lead
upto 50 m and for all lift

2.2.1 All kinds of soil 1.00 Cum 395.30 One Cubic 395.00
Metre
2.3 Banking excavated earth by mechanical / manual
means in layers not exceeding 20 cm in depth, breaking
clods, watering, rolling each layer with 1/2 tonne roller,
or wooden or steel rammers, and roiling every 3rd and
top-most layer with power roller of minimum 8 tonnes
and dressing up, in embankments for roads, flood
banks, marginal banks, and guide banks etc, lead upto
50 m and for all lift:

2.3.1 All kinds of soil 1.00 Cum 197.90 One Cubic 198.00
Metre
2.4 Deduct for not rolling with power roller of minimum 8 1.00 Cum -5.25 One Cubic -5.00
tonnes for banking excavated earth in layers not Metre
exceeding 20 cm in depth.
2.5 Deduct for not watering the excavated earth for 1.00 Cum -14.25 One Cubic -14.00
banking Metre
2.6 Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means over areas
(exceeding 30cm in depth, 1.5m in width as well as 10
sqm on plan) including getting out and disposal of
excavated earth, lead up to 50m and lift up to 1.5m,as
directed by Engineer-in-Charge.

2.6.1 All kinds of soil 1.00 Cum 177.50 One Cubic 178.00
Metre
2.7 Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means over areas
(exceeding 30 cm in depth, 1.5m in width as well as 10
sqm on plan) including getting out and disposal of
excavated earth, lead up to 50 m and lift up to 1.5m, as
directed by Engineer-in-Charge.

2.7.1 Ordinary rock 1.00 Cum 498.90 One Cubic 499.00

Metre
2.7.2 Hard rock (requiring blasting) 1.00 Cum 874.40 One Cubic 874.00
Metre

DSR - 2023 IN MS EXCEL Page 3 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
2.7.3 Hard rock (blasting prohibited) 1.00 Cum 1432.95 One Cubic 1433.00
Metre
2.8 Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10
sqm on plan) including dressing of sides and ramming of
bottoms, lift up to 1.5 m, including getting out the
excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m.

2.8.1 All kinds of soil. 1.00 Cum 260.30 One Cubic 260.00
Metre
2.9 Excavation work by mechanical means (Hydraulic
excavator)/ manual means in foundation trenches or
drains (not exceeding 1.5m in width or 10 sqm on plan)
including dressing of sides and ramming of bottoms, lift
up to 1.5 m, including getting out the excavated soil and
disposal of surplus excavated soils as directed, within a
lead of 50m.

2.9.1 Ordinary rock 1.00 Cum 632.95 One Cubic 633.00

Metre
2.9.2 Hard rock (requiring blasting) 1.00 Cum 1049.80 One Cubic 1050.00
Metre
2.9.3 Hard rock (blasting prohibited) 1.00 Cum 1523.05 One Cubic 1523.00
Metre
2.10 Excavating trenches of required width for pipes, cables,
etc including excavation for sockets, and dressing of
sides, ramming of bottoms, depth up to 1.5 m, including
getting out the excavated soil, and then returning the
soil as required, in layers not exceeding 20 cm in depth,
including consolidating each deposited layer by
ramming, watering, etc. and disposing of surplus
excavated soil as directed, within a lead of 50 m :

2.10.1 All kinds of soil

2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. 1.00 Nos 215.60 One Metre 216.00
2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not 1.00 Nos 352.15 One Metre 352.00
exceeding 300 mm dia
2.10.1.3 Pipes, cables etc. exceeding 300 mm dia but not 1.00 Nos 549.75 One Metre 550.00
exceeding 600 mm.
2.13 Excavating trenches of required width for pipes, cables,
etc, including excavation for sockets, depth up to 1.5 m,
including getting out the excavated materials, returning
the soil as required in layers not exceeding 20 cm in
depth, including consolidating each deposited layers by
ramming, watering etc., stacking serviceable material
for measurements and disposal of unserviceable
material as directed, within a lead of 50m :

2.13.1 Ordinary rock :

2.13.1.1 Pipes, cables etc. not exceeding 80 mm dia. 1.00 Nos 403.30 One Metre 403.00
2.13.1.2 Pipes, cables etc. exceeding 80 mm dia but not 1.00 Nos 998.65 One Metre 999.00
exceeding 300 mm dia.
2.13.1.3 Pipes, cables exceeding 300 mm dia but not exceeding 1.00 Nos 1149.10 One Metre 1149.00
600mm dia
2.13.2 Hard rock (requiring blasting)
2.13.2.1 Pipes, cables etc. not exceeding 80 mm dia. 1.00 Nos 603.20 One Metre 603.00
2.13.2.2 Pipes, cables etc. exceeding 80 mm dia. but not 1.00 Nos 1493.60 One Metre 1494.00
exceeding 300 mm dia.

DSR - 2023 IN MS EXCEL Page 4 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
2.13.2.3 Pipes, cables etc. exceeding 300 mm dia but not 1.00 Nos 1718.45 One Metre 1718.00
exceeding 600mm dia
2.13.3 Hard rock (blasting prohibited)
2.13.3.1 Pipes, cables etc. not exceeding 80 mm dia. 1.00 Nos 826.80 One Metre 827.00
2.13.3.2 Pipes, cables etc. exceeding 80 mm dia. but not 1.00 Nos 2047.30 One Metre 2047.00
exceeding 300 mm dia.
2.13.3.3 Pipes, cables etc. exceeding 300 mm dia but not 1.00 Nos 2355.75 One Metre 2356.00
exceeding 600mm dia.
2.14 Extra for excavating trenches for pipes, cables etc. in
ordinary / hard rock exceeding 1.5m in depth but not
exceeding 3m.(Rate is over corresponding basic item for
depth upto 1.5 metre).

2.14.1 Ordinary rock

2.14.1.1 Pipes, cables etc., exceeding 80 mm dia but not 1.00 m 729.80 One metre 730.00
exceeding 300 mm dia.
2.14.1.2 Pipes, cables etc., exceeding 300 mm dia but not 1.00 m 867.45 One metre 867.00
exceeding 600 mm dia.
2.14.2 Hard rock
2.14.2.1 Pipes, cables etc., exceeding 80 mm dia but not 1.00 m 1091.45 One metre 1091.00
exceeding 300 mm dia.
2.14.2.2 Pipes, cables etc., exceeding 300 mm dia but not 1.00 m 1297.40 One metre 1297.00
exceeding 600 mm dia.
2.14.3 Hard rock (blasting prohibited)
2.14.3.1 Pipes, cables etc., exceeding 80 mm dia but not 1.00 m 1496.10 One metre 1496.00
exceeding 300 mm dia.
2.14.3.2 Pipes, cables etc., exceeding 300 mm dia but not 1.00 m 1778.15 One metre 1778.00
exceeding 600 mm dia.
2.15 Extra for excavating trenches for pipes, cables etc. in
ordinary / hard rock exceeding 3m in depth, but not
exceeding 4.5m.(Rate is over corresponding basic item
for depth upto 1.5 metre).

2.15.1 Ordinary rock

2.15.1.1 Pipes, cables etc., exceeding 300 mm dia but not 1.00 m 2352.25 One metre 2352.00
exceeding 600 mm dia.
2.16 Close timbering in trenches including strutting, shoring
and packing cavities (wherever required) complete.
(Measurements to be taken of the face area timbered).

2.16.1 Depth not exceeding 1.5 m. 1.00 Sqm 139.95 One Square 140.00
Metre
2.16.2 Depth exceeding 1.5 m but not exceeding 3 m. 1.00 Sqm 155.30 One Square 155.00
Metre
2.16.3 Depth exceeding 3 m but not exceeding 4.5 m. 1.00 Sqm 189.65 One Square 190.00
Metre
2.17 Close timbering in case of shafts, wells, cesspits,
manholes and the like including strutting, shoring and
packing cavities (wherever required) etc. complete.
(Measurements to be taken of the face area timbered).

2.17.1 Depth not exceeding 1.5 m. 1.00 Sqm 151.50 One Square 152.00
Metre
2.17.2 Depth exceeding 1.5 m but not exceeding 3 m. 1.00 Sqm 184.00 One Square 184.00
Metre
2.17.3 Depth exceeding 3 m but not exceeding 4.5 m. 1.00 Sqm 218.20 One Square 218.00
Metre
2.18 Close timbering over areas including strutting, shoring
and packing cavities (wherever required) etc. complete.
(Measurements to be taken of the face area timbered) :

DSR - 2023 IN MS EXCEL Page 5 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
2.18.1 Depth not exceeding 1.5 m. 1.00 Sqm 125.80 One Square 126.00
Metre
2.18.2 Depth exceeding 1.5 m but not exceeding 3 m. 1.00 Sqm 144.10 One Square 144.00
Metre
2.18.3 Depth exceeding 3 m but not exceeding 4.5 m. 1.00 Sqm 163.15 One Square 163.00
Metre
2.19 Extra for planking, strutting and packing materials for 1.00 Sqm 1692.45 One Square 1692.00
cavities (in close timbering) if required to be left Metre
permanently in position. (Face area of timber
permanently left to be measured).

2.20 Open timbering in trenches including strutting and

shoring complete (measurements to be taken of the
face area timbered):
2.20.1 Depth not exceeding 1.5 m. 1.00 Sqm 72.05 One Square 72.00
Metre
2.20.2 Depth exceeding 1.5 m but not exceeding 3 m. 1.00 Sqm 81.60 One Square 82.00
Metre
2.20.3 Depth exceeding 3 m but not exceeding 4.5 m. 1.00 Sqm 97.25 One Square 97.00
Metre
2.21 Open timbering in case of shafts, wells, cesspits,
manholes and the like including strutting and shoring
complete (Measurements to be taken of the face area
timbered):

2.21.1 Depth not exceeding 1.5 m. 1.00 Sqm 66.40 One Square 66.00
Metre
2.21.2 Depth exceeding 1.5 m but not exceeding 3 m. 1.00 Sqm 81.65 One Square 82.00
Metre
2.21.3 Depth exceeding 3 m but not exceeding 4.5 m. 1.00 Sqm 101.85 One Square 102.00
Metre
2.22 Open timbering over areas including strutting, shoring
etc. complete. (Measurements to be taken of the face
area timbered):
2.22.1 Depth not exceeding 1.5 m. 1.00 Sqm 44.85 One Square 45.00
Metre
2.22.2 Depth exceeding 1.5 m but not exceeding 3 m. 1.00 Sqm 54.95 One Square 55.00
Metre
2.22.3 Depth exceeding 3 m but not exceeding 4.5 m. 1.00 Sqm 71.30 One Square 71.00
Metre
2.23 Extra for planking and strutting in open timbering if 1.00 Sqm 872.55 One Square 873.00
required to be left permanently in position. (Face area Metre
of the timber permanently left to be measured).
2.25 Filling available excavated earth (excluding rock) in 1.00 Cum 196.00 One Cubic 196.00
trenches, plinth, sides of foundations etc. in layers not Metre
exceeding 20cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
up to 1.5 m.

2.25A Excavating, supplying and filling of local earth (including 1.00 Cum 700.50 One Cubic 701.00
royalty) by mechanical transport up to a lead of 5 km, Metre
also including ramming and watering of the earth in
layers not exceeding 20 cm in trenches, plinth, sides of
foundation etc., complete.

2.26 Extra for every additional lift of 1.5 m or part thereof in

excavation /banking excavated or stacked materials.

2.26.1 All kinds of soil. 1.00 Cum 126.80 One Cubic 127.00
Metre
2.26.2 Ordinary or hard rock. 1.00 Cum 227.40 One Cubic 227.00
Metre

DSR - 2023 IN MS EXCEL Page 6 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
2.27 Supplying and filling in plinth with sand under floors, 1.00 Cum 2123.75 One Cubic 2124.00
including watering, ramming, consolidating and Metre
dressing complete.
2.28 Surface dressing of the ground including removing
vegetation and inequalities not exceeding 15 cm deep
and disposal of rubbish, lead up to 50 m and lift upto1.5
m.

2.28.1 All kinds of soil. 1.00 Sqm 34.15 One Square 34.00
Metre
2.29 Ploughing the existing ground to a depth of 15 cm to 25
cm and watering the same.
2.29.1 All kinds of soil. 1.00 Sqm 34.60 One Square 35.00
Metre
2.30 Excavating holes more than 0.10 cum & up to 0.5 cum
including getting out the excavated soil, then returning
the soil as required in layers not exceeding 20 cm in
depth, including consolidating each deposited layer by
ramming, watering etc, disposing of surplus excavated
soil, as directed within a lead of 50 m and lift upto1.5
m.

2.30.1 All kinds of soil. 1.00 No. 82.45 Each 82.00

2.30.2 Ordinary rock 1.00 No. 194.25 Each 194.00
2.30.3 Hard rock (requiring blasting) 1.00 No. 319.30 Each 319.00
2.30.4 Hard rock (blasting prohibited) 1.00 No. 461.30 Each 461.00
2.31 Clearing jungle including uprooting of rank vegetation, 1.00 Sqm 17.60 One Square 18.00
grass, brush wood, trees and saplings of girth up to 30 Metre
cm measured at a height of 1 m above ground level and
removal of rubbish up to a distance of 50m outside the
periphery of the area cleared.

2.32 Clearing grass and removal of the rubbish up to a 1.00 Sqm 8.95 One Square 9.00
distance of 50 m outside the periphery of the area Metre
cleared.
2.33 Felling trees of the girth (measured at a height of 1 m
above ground level) including cutting of trunks and
branches, removing the roots and stacking of
serviceable material and disposal of unserviceable
material.

2.33.1 Beyond 30 cm girth up to and including 60 cm girth 1.00 No. 532.35 Each 532.00
2.33.2 Beyond 60 cm girth up to and including 120 cm girth 1.00 No. 2373.50 Each 2374.00
2.33.3 Beyond 120 cm girth up to and including 240 cm girth 1.00 No. 11020.15 Each 11020.00
2.33.4 Above 240 cm girth 1.00 No. 22075.20 Each 22075.00
2.34 Supplying chemical emulsion in sealed containers
including delivery as specified.
2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 1.00 Ltr 234.75 One Litre 235.00

2.35 Diluting and injecting chemical emulsion for POST-

CONSTRUCTIONAL anti- termite treatment (excluding
the cost of chemical emulsion) :
2.35.1 Along external wall where the apron is not provided
using chemical emulsion @ 7.5 litres / sqm of the
vertical surface of the substructure to a depth of 300
mm including excavation channel along the wall &
rodding etc. complete:

2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% 1.00 Nos 38.90 One Metre 39.00
concentration.
2.35.2 Along the external wall below concrete or masonry
apron using chemical emulsion @ 2.25 litres per linear
metre including drilling and plugging holes etc.

DSR - 2023 IN MS EXCEL Page 7 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
2.35.2.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% 1.00 Nos 53.45 One Metre 53.00
concentration.
2.35.3 Treatment of soil under existing floors using chemical
emulsion @ one litre per hole, 300 mm apart including
drilling 12 mm diameter holes and plugging with
cement mortar 1 :2 (1 cement : 2 Coarse sand) to match
the existing floor :

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% 1.00 Sqm 310.05 One Square 310.00
concentration. Metre
2.35.4 Treatment of existing masonry using chemical emulsion
@ one litre per hole at 300 mm interval including
drilling holes at 45 degree and plugging them with
cement mortar 1:2 (1 cement : 2 coarse sand) to the full
depth of the hole :

2.35.4.1 With Chlorpyriphos/Lindane E.C. 20% with 1% 1.00 Nos 43.00 One Metre 43.00
concentration.
2.35.5 Treatment at points of contact of wood work by 1.00 Nos 279.70 One Metre 280.00
chemical emulsion Chlorpyriphos/ Lindane (in oil or
kerosene based solution) @ 0.5 litres per hole by
drilling 6 mm dia holes at downward angle of 45 degree
at 150 mm centre to centre and sealing the same.

2.36 Extra for levelling & neatly dressing of disposed soil 1.00 Cum 93.05 One Cubic 93.00
completely as directed by Engineer-in-Charge. Metre
2.37 Supply and stacking of Fly ash conforming to IRC- 58 at 1.00 Cum 281.05 One Cubic 281.00
site, including carriage, loading , unloading & stacking Metre
up to any lead (measured stacks will be reduced by 20%
for payment).

2.38 Filling with available fly ash and earth (excluding rock) 1.00 Cum 308.20 One Cubic 308.00
in trenches or embankment in layers (each layer should Metre
not exceed 15 cm), with intermediate layer of
compacted earth (Soil density of 98%) after every four
layers of compacted depth of fly ash, sides & top layer
of filling shall be done with earth having total minimum
compacted thickness 30 cm or as decided by Engineer -
in- charge, including compacting each layer by rolling/
ramming and watering , all complete as per drawing
and direction of Engineer -in - charge.

Total of the Sub-Head - Earth Work : 76358.00

Sub-Head : Concrete Work
4.1 Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
4.1.2 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived 1.00 Cum 8340.85 One Cubic 8341.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).
4.1.2A 1:1.5:3 (1 Cement: 1.5 coarse sand(zone-III) including 1.00 Cum 8127.80 One Cubic 8128.00
manufactured sand derived from Recycled concrete Metre
aggregate (RCA) up to 25% : 3 graded stone aggregate
20 mm nominal size incuding Recycled Concrete
Aggregate (RCA) up to 25%).

4.1.3 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from 1.00 Cum 7878.50 One Cubic 7879.00
natural sources : 4 graded stone aggregate 20 mm Metre
nominal size derived from natural sources)

DSR - 2023 IN MS EXCEL Page 8 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.1.3A 1:2:4 (1 cement : 2 coarse sand(zone-III) including 1.00 Cum 7654.85 One Cubic 7655.00
manufactured sand derived from Recycled concrete Metre
aggregate (RCA) up to 25% : 4 graded stone aggregate
20 mm nominal size including Recycled Concrete
Aggregate (RCA) upto 25% )

4.1.4 1:2:4 (1 Cement : 2 coarse sand(zone-III) derived from 1.00 Cum 7780.30 One Cubic 7780.00
natural sources : 4 graded stone aggregate 40 mm Metre
nominal size derived from natural sources).
4.1.5 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from 1.00 Cum 7294.70 One Cubic 7295.00
natural sources : 6 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).
4.1.5A 1:3:6 (1 Cement : 3 manufactured sand derived from 1.00 Cum 6347.75 One Cubic 6348.00
Recycled Concrete Aggregate (RCA) : 6 graded stone Metre
aggregate 20 mm nominal size Recycled Concrete
Aggregate (RCA)).

4.1.5B 1:3:6 (1 Cement : 3 manufactured sand derived from 1.00 Cum 5639.85 One Cubic 5640.00
Recycled concrete Aggregate (RCA) : 6 graded stone Metre
aggregate 20 mm nominal size Recycled Aggregate
(RA)).

4.1.6 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from 1.00 Cum 7178.75 One Cubic 7179.00
natural sources : 6 graded stone aggregate 40 mm Metre
nominal size derived from natural sources).
4.1.6A 1:3:6 (1 Cement : 3 manufactured sand derived from 1.00 Cum 5572.00 One Cubic 5572.00
Recycled Concrete Aggregate (RCA) up to 25% : 6 Metre
graded stone aggregate 40 mm nominal size Recycled
Aggregate (RA)).

4.1.8 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from 1.00 Cum 6812.00 One Cubic 6812.00
natural sources : 8 graded stone aggregate 40 mm Metre
nominal size derived from natural sources).
4.1.8A 1:4:8 (1 Cement : 4 manufactured sand derived from 1.00 Cum 5205.25 One Cubic 5205.00
Recycled Concrete Aggregate (RCA) : 8 graded stone Metre
aggregate 40 mm nominal size Recycled Aggregate
(RA)).

4.1.10 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from 1.00 Cum 6518.60 One Cubic 6519.00
natural sources : 10 graded stone aggregate 40 mm Metre
nominal size derived from natural sources)
4.1.10A 1:5:10 (1 cement : 5 manufactured sand derived from 1.00 Cum 4911.85 One Cubic 4912.00
Recycled Concrete Aggregate (RCA) : 10 graded stone Metre
aggregate 40 mm nominal size including Recycled
Aggregate (RA))

4.1.11 1:5:10 (1 cement : 5 fine sand derived from natural 1.00 Cum 6189.65 One Cubic 6190.00
sources : 10 graded stone aggregate 40 mm nominal Metre
size derived from natural sources)
4.1.12 1:2:3½:9 (1 ordinary portland cement : 2 Fly ash : 3½ 1.00 Cum 6667.25 One Cubic 6667.00
coarse sand (zone-III) derived from natural sources : 9 Metre
graded stone aggregate 40 mm nominal size derived
from natural sources).

4.1.12A 1:2:3½:9 (1 ordinary portland cement : 2 Fly ash : 3½ 1.00 Cum 5130.65 One Cubic 5131.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) : 9 graded stone aggregate 40 mm
nominal size Recycled Aggregate (RA)).

4.1.13 1:2½:4:11 (1 ordinary portland cement : 2½ fly ash : 4 1.00 Cum 6311.95 One Cubic 6312.00
coarse sand (zone-III) derived from natural sources) : 11 Metre
graded stone aggregate 40 mm nominal size derived
from natural sources)

4.1.13A 1:2½:4:11 (1 ordinary portland cement : 2½ fly ash : 4 1.00 Cum 4796.40 One Cubic 4796.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) : 11 graded stone aggregate 40 mm
nominal size Recycled Aggregate (RA))

DSR - 2023 IN MS EXCEL Page 9 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.2 Providing and laying cement concrete in retaining walls,
return walls, walls (any thickness) including attached
pilasters, columns, piers, abutments, pillars, posts,
struts, buttresses, string or lacing courses, parapets,
coping, bed blocks, anchor blocks, plain window sills,
fillets, sunken floor, etc., up to floor five level, excluding
the cost of centering, shuttering and finishing :

4.2.2 1:1½:3 (1 cement : 1½ coarse sand(zone-III) derived 1.00 Cum 10357.55 One Cubic 10358.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).
4.2.2A 1:1½:3 (1 cement : 1½ coarse sand (zone-III) including 1.00 Cum 10144.50 One Cubic 10145.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 3 graded stone aggregate
20 mm nominal size including Recycled Concrete
Aggregate (RCA) upto 25%).

4.2.3 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from 1.00 Cum 9895.20 One Cubic 9895.00
natural sources : 4 graded stone aggregate 20 mm Metre
nominal size derived from natural sources)
4.2.3A 1:2:4 (1 Cement : 2 coarse sand (zone-III) including 1.00 Cum 9671.50 One Cubic 9672.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 4 graded stone aggregate
20 mm nominal size including Recycled Concrete
Aggregate (RCA) upto 25%).

4.2.5 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from 1.00 Cum 9311.40 One Cubic 9311.00
natural sources : 6 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).
4.2.5A 1:3:6 (1 cement : 3 manufactured sand derived from 1.00 Cum 8364.45 One Cubic 8364.00
Recycled Concrete Aggregate (RCA) : 6 graded stone Metre
aggregate 20 mm nominal size Recycled Concrete
Aggregate (RCA))

4.2.5B 1:3:6 (1 cement : 3 manufactured sand derived from 1.00 Cum 7656.55 One Cubic 7657.00
Recycled Concrete Aggregate (RCA) : 6 graded stone Metre
aggregate 20 mm nominal size Recycled Aggregate
(RA)).

4.2.8 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from 1.00 Cum 8519.20 One Cubic 8519.00
natural sources : 10 graded stone aggregate 40 mm Metre
nominal size derived from natural sources).
4.2.8A 1:5:10 (1 cement : 5 manufactured sand derived from 1.00 Cum 6912.45 One Cubic 6912.00
Recycled Concrete Aggregate (RCA) : 10 graded stone Metre
aggregate 40 mm nominal size Recycled Aggregate
(RA)).

4.3 Centering and shuttering including strutting, propping

etc. and removal of form work for :
4.3.1 Foundations, footings, bases for columns. 1.00 Sqm 392.15 One Square 392.00
Metre
4.3.2 Retaining walls, return walls, walls (any thickness) 1.00 Sqm 842.50 One Square 843.00
including attached pilasters, buttresses, plinth and Metre
string courses fillets, kerbs and steps etc..
4.3.3 Columns, piers, abutments, pillars, posts and struts. 1.00 Sqm 961.30 One Square 961.00
Metre
4.4 Providing and laying cement concrete in kerbs, steps
and the like at or near ground level excluding the cost
of centering, shuttering and finishing.
4.4.1 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) derived 1.00 Cum 8340.85 One Cubic 8341.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).

DSR - 2023 IN MS EXCEL Page 10 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.4.1A 1:1.5:3 (1 Cement : 1.5 coarse sand (zone-III) including 1.00 Cum 8127.80 One Cubic 8128.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 3 graded stone aggregate
20 mm nominal size including Recycled Concrete
Aggregate (RCA) upto 25%).

4.5 Providing and fixing up to floor five level precast

cement concrete string or lacing courses, copings, bed
plates, anchor blocks, plain window sills, shelves,
louvers, steps, stair cases, etc. including hoisting and
setting in position with cement mortar 1:3 (1 Cement : 3
coarse sand), cost of required Centering complete.

4.5.1 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived 1.00 Cum 10105.10 One Cubic 10105.00
from natural sources : 3 graded stone aggregate 20mm Metre
nominal size derived from natural sources).
4.5.1A 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) including 1.00 Cum 9893.45 One Cubic 9893.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 3 graded stone aggregate
20mm nominal size Recycled Concrete Aggregate (RCA)
up to 25%).

4.6 Providing and fixing at or near ground level precast

cement concrete in kerbs, edgings etc. as per approved
pattern and setting in position with cement mortar 1:3
(1 Cement : 3 coarse sand), including the cost of
required centering, shuttering complete.

4.6.1 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) derived 1.00 Cum 8726.85 One Cubic 8727.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).
4.6.1A 1:1.5:3 (1 Cement : 1.5 coarse sand (zone-III) including 1.00 Cum 8514.85 One Cubic 8515.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 3 graded stone aggregate
20 mm nominal size Recycled Concrete Aggregate (RCA)
up to 25%).

4.7 Providing and fixing up to floor five level precast

cement concrete solid block including hoisting and
setting in position with cement mortar 1:3 (1 cement : 3
coarse sand), cost of required centering, shuttering
complete :

4.7.1 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) derived 1.00 Cum 17889.25 One Cubic 17889.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).
4.7.1A 1:1.5:3 (1 Cement : 1.5 coarse sand (zone-III) including 1.00 Cum 17677.25 One Cubic 17677.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 3 graded stone aggregate
20 mm nominal size including (Recycled Concrete
Aggregate (RCA) up to 25%).

4.8 Providing and fixing up to floor five level precast

cement concrete hollow block including hoisting and
setting in position with cement mortar 1:3 (1 cement : 3
coarse sand), cost of required centering, shuttering
complete.

4.8.1 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) derived 1.00 Cum 14624.20 One Cubic 14624.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources).

DSR - 2023 IN MS EXCEL Page 11 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.8.1A 1:1.5:3 (1 Cement : 1.5 coarse sand (zone-III) including 1.00 Cum 14526.20 One Cubic 14526.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 25% : 3 graded stone aggregate
20 mm nominal size including (Recycled Concrete
Aggregate (RCA) up to 25%).

4.9 Precasting and placing in position 125 mm dia Bollards 1.00 No. 929.80 Each 930.00
600 mm high of required shape including providing M.S.
Pipe Sleeve 50 mm dia 300 mm long in the Bollard and
M.S. Pipes 40 mm dia and 450mm long with
150x150x6mm M.S. plate welded at bottom and
embedded 150mm in cement concrete 1:3:6 (1
Cement : 3 coarse sand (zone-III) derived from natural
sources : 6 graded stone aggregate 20 mm nominal size
derived from natural sources), including necessary
excavation of size 250x250x450mm deep for the same
in bitumen/ concrete pavement at specified spacing.

4.9A Precasting and placing in position 125 mm dia Bollards 1.00 No. 900.15 Each 900.00
600 mm high of required shape including providing M.S.
Pipe Sleeve 50 mm dia 300 mm long in the Bollard and
M.S. Pipes 40 mm dia and 450mm long with
150x150x6mm M.S. plate welded at bottom and
embedded 150mm in cement concrete 1:3:6 (1
Cement : 3 manufactured sand derived from Recycled
Concrete Aggregate (RCA) : 6 graded stone aggregate
20 mm nominal size (Recycled Concrete Aggregate
(RCA)), including necessary excavation of size
250x250x450mm deep for the same in bitumen/
concrete pavement at specified spacing.

4.9B Precasting and placing in position 125 mm dia Bollards 1.00 No. 878.90 Each 879.00
600 mm high of required shape including providing M.S.
Pipe Sleeve 50 mm dia 300 mm long in the Bollard and
M.S. Pipes 40 mm dia and 450mm long with
150x150x6mm M.S. plate welded at bottom and
embedded 150mm in cement concrete 1:3:6 (1
Cement : 3 manufactured sand derived from Recycled
Concrete Aggregate (RCA) : 6 graded stone aggregate
20 mm nominal size (Recycled Aggregate (RA), including
necessary excavation of size 250x250x450mm deep for
the same in bitumen/ concrete pavement at specified
spacing.

4.10 Providing and laying damp-proof course 40mm thick 1.00 Sqm 410.85 One Square 411.00
with cement concrete 1:2:4 (1 cement : 2 coarse sand Metre
(zone-III) derived from natural sources : 4 graded stone
aggregate 12.5mm nominal size derived from natural
sources).

4.10A Providing and laying damp-proof course 40mm thick 1.00 Sqm 402.50 One Square 403.00
with cement concrete 1:2:4 (1 cement : 2 coarse sand Metre
(zone-III) including manufactured sand derived from
Recycled Concrete Aggregate (RCA) up to 25% : 4
graded stone aggregate 12.5mm nominal size including
(Recycled Concrete Aggregate (RCA) up to 25%)).

4.11 Providing and laying damp-proof course 50mm thick 1.00 Sqm 495.75 One Square 496.00
with cement concrete 1:2:4 (1 cement : 2 coarse sand Metre
(zone-III) derived from natural sources : 4 graded stone
aggregate 20mm nominal size derived from natural
sources).

DSR - 2023 IN MS EXCEL Page 12 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.11A Providing and laying damp-proof course 50mm thick 1.00 Sqm 484.60 One Square 485.00
with cement concrete 1:2:4 (1 cement : 2 coarse sand Metre
(zone-III) including manufactured sand derived from
Recycled Concrete Aggregate (RCA) up to 25% : 4
graded stone aggregate 20mm nominal size (Recycled
concrete aggregate (RCA) up to 25%)).

4.12 Extra for providing and mixing water proofing material 1.00 units 18.15 per bag of 50 18.00
in cement concrete work in doses by weight of cement kg cement
as per manufacturer’s specification. used
4.13 Providing and applying a coat of residual petroleum 1.00 Sqm 146.15 One Square 146.00
bitumen of grade of VG-10 of approved quality using Metre
1.7 kg per square metre on damp proof course after
cleaning the surface with brushes and finally with a
piece of cloth lightly soaked in kerosene oil.

4.14 Extra for concrete work in superstructure above floor V 1.00 Cum 169.45 One Cubic 169.00
level for each four floors or part thereof by mechanical Metre
means.
4.15 Extra for laying concrete in or under water and/or liquid 1.00 units 1098.80 cum per 1099.00
mud including cost of pumping or bailing out water and metre depth
removing slush etc. complete. Note for item No. 4.15 :-
The quantity will be calculated by multiplying the depth
measured from the sub-soil water level up to centre of
gravity of concrete under sub-soil water level with
quantity of concrete in cum executed under sub-soil
water. The depth of centre of gravity shall be reckoned
correct to 0.1m. (0.05m or more shall be taken as 0.1m
and less than0.05m ignored).

4.16 Extra for laying concrete in or under foul positions. 1.00 Cum 467.55 One Cubic 468.00
Metre
4.17 Making plinth protection 50mm thick of cement 1.00 Sqm 749.30 One Square 749.00
concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) Metre
derived from natural sources : 6 graded stone
aggregate 20 mm nominal size derived from natural
sources) over 75mm thick bed of dry brick ballast 40
mm nominal size, well rammed and consolidated and
grouted with fine sand, including necessary excavation
leveling & dressing & finishing the top smooth.

4.17A Making plinth protection 50mm thick of cement 1.00 Sqm 702.30 One Square 702.00
concrete 1:3:6 (1 cement : 3 manufactured sand Metre
derived from Recycled Concrete Aggregate (RCA) : 6
graded stone aggregate 20 mm nominal size Recycled
Concrete Aggregate (RCA) over 75mm thick bed of dry
brick ballast 40 mm nominal size, well rammed and
consolidated and grouted with fine sand, including
necessary excavation leveling & dressing & finishing the
top smooth.

4.17B Making plinth protection 50mm thick of cement 1.00 Sqm 666.90 One Square 667.00
concrete 1:3:6 (1 cement : 3 manufactured sand Metre
derived from Recycled Concrete Aggregate (RCA) : 6
graded stone aggregate 20 mm nominal size Recycled
Concrete Aggregate (RCA) over 75mm thick bed of dry
brick ballast 40 mm nominal size, well rammed and
consolidated and grouted with fine sand, including
necessary excavation leveling & dressing & finishing the
top smooth.

DSR - 2023 IN MS EXCEL Page 13 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.18 Extra for addition of synthetic Polyester triangular fiber 1.00 units 70.35 Per Bag of 70.00
of length 12mm, effective diameter 10-40 microns and 50Kg. of
specific gravity of 1.34 to 1.40 in cement concrete/ cement
RCC/ Flooring/ water retaining structures by using 125
gram of synthetic Polyester triangular fiber for 50 Kg
cement used as per direction of Engineer-in-Charge.

4.20 Providing and laying in position ready mixed or site

batched design mix cement concrete for plain cement
concrete work; using coarse aggregate and fine
aggregate derived from natural sources, Portland
Pozzolana/Ordinary Portland/Portland Slag cement,
admixtures in recommended proportions as per IS :
9103 to accelerate/ retard setting of concrete, to
improve durability and workability without impairing
strength; including pumping of concrete to site of
laying, curing, carriage for all leads; but excluding the
cost of centering, shuttering and finishing as per
direction of the Engineer-in-charge; for the following
grades of concrete.

Note : Extra cement upto 10% of the minimum

specified cement content in design mix shall be payable
separately. In case the cement content in design mix is
more than 110% of the minimum specified cement
content, the contractor shall have discretion to either
re-design the mix or bear the cost of extra cement.

4.20.1 All works up to plinth level:

4.20.1.1 Concrete of M-10 grade with minimum cement content 1.00 Cum 8835.15 One Cubic 8835.00
of 220 kg/cum. Metre
4.20.1.2 Concrete of M-15 grade with minimum cement content 1.00 Cum 8986.15 One Cubic 8986.00
of 240 kg/cum. Metre
4.20.1.3 Concrete of M20 grade with minimum cement content 1.00 Cum 9212.60 One Cubic 9213.00
of 270 kg /cum Metre
4.20.1.4 Concrete of M25 grade with minimum cement content 1.00 Cum 9439.05 One Cubic 9439.00
of 300 kg /cum Metre
4.20.2 All works above plinth and upto floor V level :
4.20.2.1 Concrete of M-10 grade with minimum cement content 1.00 Cum 9190.80 One Cubic 9191.00
of 220 kg/cum. Metre
4.20.2.2 Concrete of M-15 grade with minimum cement content 1.00 Cum 9341.80 One Cubic 9342.00
of 240 kg/cum. Metre
4.20.2.3 Concrete of M20 grade with minimum cement content 1.00 Cum 9568.25 One Cubic 9568.00
of 270 kg /cum Metre
4.20.2.4 Concrete of M25 grade with minimum cement content 1.00 Cum 9794.70 One Cubic 9795.00
of 300 kg /cum Metre

DSR - 2023 IN MS EXCEL Page 14 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
4.20A Providing and laying in position ready mixed or site
batched design mix cement concrete for plain cement
concrete work; using coarse aggregate and fine
aggregate derived from natural sources and using
recycled concrete aggregate (RCA) as coarse aggregate
and fine aggregate within the permissible utilization,
Portland Pozzolana / Ordinary Portland/Portland Slag
cement, admixtures in recommended proportions as
per IS: 9103 to accelerate / retard setting of concrete to
improve durability and workability without impairing
strength; including pumping of concrete to site of
laying, curing, carriage for all leads; but excluding the
cost of centering, shuttering and finishing as per
direction of the engineer-in-charge; for the following
grades of concrete.

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be payable
separately. In case the cement content in design mix is
more than 110% of the minimum specified cement
content, the contractor shall have discretion to either
re-design the mix or bear the cost of extra cement.

4.20A.1 All works upto plinth level

4.20A.1.1 Concrete of M10 grade with minimum cement content
of 220 kg /cum.
(Note: The permissible utilization of Recycled Concrete 1.00 Cum 7936.10 One Cubic 7936.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 100% each).
4.20A.1.2 Concrete of M15 grade with minimum cementcontent
of 240 kg /cum.
(Note: The permissible utilization of Recycled Concrete 1.00 Cum 8779.40 One Cubic 8779.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 25% each).
4.20A.1.3 Concrete of M20 grade with minimum cement content
of 270 kg /cum.
(Note:The permissible utilization of RecycledConcrete 1.00 Cum 9005.85 One Cubic 9006.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 25% each).
4.20A.1.4 Concrete of M25 grade with minimum cement content
of 300 kg /cum.
(Note: The permissible utilization of Recycled Concrete 1.00 Cum 9232.30 One Cubic 9232.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 25% each).
4.20A.2 All works above plinth and upto floor V level
4.20A.2.1 Concrete of M10 grade with minimum cement content
of 220 kg /cum.
(Note: The permissible utilization of Recycled Concrete 1.00 Cum 8291.75 One Cubic 8292.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 100% each).
4.20A.2.2 Concrete of M15 grade with minimum cement content
of 240 kg /cum.
(Note: The permissible utilization of Recycled Concrete 1.00 Cum 9135.05 One Cubic 9135.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 25% each).
4.20A.2.3 Concrete of M20 grade with minimum cement content
of 270 kg /cum.

DSR - 2023 IN MS EXCEL Page 15 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
(Note: The permissible utilization of Recycled Concrete 1.00 Cum 9361.50 One Cubic 9362.00
Aggregate (RCA) as coarse aggregate and fine aggregate Metre
is 25% each).
4.20A.2.4 Concrete of M25 grade with minimum cement content 1.00 Cum 9587.95 One Cubic 9588.00
of 300 kg /cum. Metre
(Note: The permissible utilization of Recycled Concrete
Aggregate (RCA) as coarse aggregateand fine aggregate
is 25% each).
Total of the Sub-Head - Concrete Work : 480106.00
Sub-Head : Reinforced Cement Concrete
5.1 Providing and laying in position specified grade of
reinforced cement concrete, excluding the cost of
centering, shuttering, finishing and reinforcement - All
work up to plinth level :

5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived 1.00 Cum 9045.75 One Cubic 9046.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources)
5.1.2A 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) including 1.00 Cum 8874.95 One Cubic 8875.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) up to 20% : 3 graded stone aggregate
20 mm nominal size of Recycled Concrete Aggregate
(RCA) up to 20%)

5.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from 1.00 Cum 8583.40 One Cubic 8583.00
natural sources : 4 graded stone aggregate 20 mm Metre
nominal size derived from natural sources)
5.1.3A 1:2:4 (1 cement : 2 coarse sand incuding manufactured 1.00 Cum 8404.05 One Cubic 8404.00
sand derived from Recycled Concrete Aggregate (RCA) Metre
upto 20% : 4graded stone aggregate 20 mm nominal
size of Recycled Concrete Aggregate (RCA) upto 20%).

5.2 Reinforced cement concrete work in walls (any

thickness), including attached pilasters, buttresses,
plinth and string courses, fillets, columns, pillars, piers,
abutments, posts and struts etc. above plinth level up
to floor five level, excluding cost of centering,
shuttering, finishing and reinforcement :

5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived 1.00 Cum 10852.95 One Cubic 10853.00
from natural sources : 3 graded stone aggregate 20 mm Metre
nominal size derived from natural sources)
5.2.2A 1:1.5:3 (1 cement : 1.5 coarse sand incuding 1.00 Cum 10682.15 One Cubic 10682.00
manufactured sand derived from Recycled Concrete Metre
Aggregate (RCA) upto 20% : 3 graded stone aggregate
20 mm nominal size including Recycled Concrete
Aggregate (RCA) upto 20% .

5.3 Reinforced cement concrete work in beams, suspended 1.00 Cum 11505.50 One Cubic 11506.00
floors, roofs having slope up to 15° landings, balconies, Metre
shelves, chajjas, lintels, bands, plain window sills,
staircases and spiral stair cases above plinth level up to
floor five level, excluding the cost of centering,
shuttering, finishing and reinforcement with 1:1.5:3 (1
cement : 1.5 coarse sand(zone-III)derived from natural
sources : 3 graded stone aggregate 20 mm nominal
sizederived from natural sources).

DSR - 2023 IN MS EXCEL Page 16 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.3A Reinforced cement concrete work in beams, suspended 1.00 Cum 11334.70 One Cubic 11335.00
floors, roofs having slope up to 15° landings, balconies, Metre
shelves, chajjas, lintels, bands, plain window sills,
staircases and spiral stair cases above plinth level up to
floor five level excluding the cost of centering,
shuttering, finishing and reinforcement with 1:1.5:3 (1
cement : 1.5 coarse sand including manufactured sand
derived from Recycled Concrete Aggregate (RCA) upto
20% : 3 graded stone aggregate 20 mm nominal size
including Recycled Concrete Aggregate (RCA) upto
20%).

5.4 Providing and laying reinforced cement concrete in 1.00 Cum 8821.65 One Cubic 8822.00
kerbs, steps and the like at or near ground level Metre
excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) derived from natural sources : 3 graded
stone aggregate 20 mm nominal size derived from
natural sources ).

5.4A Providing and laying reinforced cement concrete in 1.00 Cum 8650.85 One Cubic 8651.00
kerbs, steps and the like at or near ground level Metre
excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand
including manufactured sand derived from Recycled
Concrete Aggregate (RCA) upto 20% : 3 graded stone
aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20%).

5.5 Reinforced cement concrete work in arches, archribs, 1.00 Cum 12205.85 One Cubic 12206.00
domes, vaults, shells, folded plate and roofs having Metre
slope more than 15° up to floor five level, excluding the
cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand
(zone-III)derived from natural sources : 3 graded stone
aggregate 20 mm nominal size derived from natural
sources ).

5.5A Reinforced cement concrete work in arches, archribs, 1.00 Cum 12035.00 One Cubic 12035.00
domes, vaults, shells, folded plate and roofs having Metre
slope more than 15° up to floor five level, excluding the
cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand
including manufactured sand derived from Recycled
Concrete Aggregate (RCA)upto 20% : 3 graded stone
aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20% ).

5.6 Reinforced cement concrete work in chimneys, shafts, 1.00 Cum 11125.20 One Cubic 11125.00
up to floor five level, excluding the cost of centering, Metre
shuttering, finishing and reinforcement with 1:1.5:3 (1
cement : 1.5 coarse sand(zone-III) derived from natural
sources: 3 graded stone aggregate 20 mm nominal size
derived from natural sources).

DSR - 2023 IN MS EXCEL Page 17 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.6A Reinforced cement concrete work in chimneys, shafts, 1.00 Cum 10954.40 One Cubic 10954.00
up to floor five level, excluding the cost of centering, Metre
shuttering, finishing and reinforcement with 1:1.5:3 (1
cement : 1.5 coarse sand including manufactured sand
derived from Recycled Concrete Aggregate (RCA)upto
20% : 3 graded stone aggregate 20 mm nominal size
including Recycled Concrete Aggregate (RCA) upto
20%).

5.7 Reinforced cement concrete work in well-steining, 1.00 Cum 8424.60 One Cubic 8425.00
excluding the cost of centering, shuttering, finishing and Metre
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) derived from natural sources: 3 graded
stone aggregate 20 mm nominal sizederived from
natural sources).

5.7A Reinforced cement concrete work in well-steining, 1.00 Cum 8253.80 One Cubic 8254.00
excluding the cost of centering, shuttering, finishing and Metre
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand
including manufactured sand derived from Recycled
Concrete Aggregate (RCA) upto 20%: 3 graded stone
aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20%).

5.8 Reinforced cement concrete work in vertical and 1.00 Cum 11454.35 One Cubic 11454.00
horizontal fins individually or forming box louvers, Metre
facias and eaves boards above plinth level up to floor
five level, excluding the cost of centering, shuttering,
finishing and reinforcement with 1:1.5:3 (1 cement : 1.5
coarse sand(zone-III)derived from natural sources : 3
graded stone aggregate 20mm nominal size derived
from natural sources).

5.8A Reinforced cement concrete work in vertical and 1.00 Cum 11283.55 One Cubic 11284.00
horizontal fins individually or forming box louvers, Metre
facias and eaves boards above plinth level up to floor
five level, excluding the cost of centering, shuttering,
finishing and reinforcement with 1:1.5:3 (1 cement : 1.5
coarse sand including manufactured sand derived from
Recycled Concrete Aggregate (RCA)upto 20% : 3 graded
stone aggregate 20mm nominal sized including
Recycled Concrete Aggregate (RCA)upto 20%).

5.9 Centering and shuttering including strutting, propping

etc. and removal of form for :
5.9.1 Foundations, footings, bases of columns, etc. for mass 1.00 Sqm 392.15 One Square 392.00
concrete Metre
5.9.2 Walls (any thickness) including attached pilasters, 1.00 Sqm 842.50 One Square 843.00
butteresses, plinth and string courses etc. Metre
5.9.3 Suspended floors, roofs, landings, balconies and access 1.00 Sqm 927.25 One Square 927.00
platform Metre
5.9.4 Shelves (Cast in situ) 1.00 Sqm 927.25 One Square 927.00
Metre
5.9.5 Lintels, beams, plinth beams, girders, bressumers and 1.00 Sqm 736.40 One Square 736.00
cantilevers Metre
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 1.00 Sqm 961.30 One Square 961.00
Metre
5.9.7 Stairs, (excluding landings) except spiral-staircases 1.00 Sqm 764.95 One Square 765.00
Metre
5.9.8 Spiral staircases (including landing) 1.00 Sqm 798.35 One Square 798.00
Metre

DSR - 2023 IN MS EXCEL Page 18 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.9.9 Arches, domes, vaults up to 6 m span 1.00 Sqm 2154.35 One Square 2154.00
Metre
5.9.10 Extra for arches, domes, vaults exceeding 6 m span 1.00 Sqm 608.15 One Square 608.00
Metre
5.9.11 Chimneys and shafts 1.00 Sqm 803.25 One Square 803.00
Metre
5.9.12 Well steining 1.00 Sqm 263.65 One Square 264.00
Metre
5.9.13 Vertical and horizontal fins individually or forming box 1.00 Sqm 1296.70 One Square 1297.00
louvers band, facias and eaves boards Metre
5.9.15 Small lintels not exceeding 1.5 m clear span, moulding 1.00 Sqm 392.15 One Square 392.00
as in cornices, window sills, string courses, bands, Metre
copings, bed plates, anchor blocks and the like

5.9.16 Edges of slabs and breaks in floors and walls

5.9.16.1 Under 20 cm wide 1.00 Nos 208.55 One Running 209.00
Metre
5.9.16.2 Above 20 cm wide 1.00 Sqm 879.05 One Square 879.00
Metre
5.9.17 Cornices and mouldings 1.00 Sqm 856.80 One Square 857.00
Metre
5.9.18 Small surfaces such as cantilever ends, brackets and 1.00 Sqm 964.85 One Square 965.00
ends of steps, caps and bases to pilasters and columns Metre
and the like
5.9.19 Weather shade, Chajjas, corbels etc., including edges 1.00 Sqm 951.10 One Square 951.00
Metre
5.9.20 Suspended floors, roofs, landings, balconies and access 1.00 Sqm 1028.40 One Square 1028.00
platform with water proof ply 12 mm thick Metre
5.9.21 Lintels, beams, plinth beams, girders, bressumers and 1.00 Sqm 841.95 One Square 842.00
cantilevers with water proof ply 12 mm thick Metre
5.10 Providing and fixing tie bolt, spring coil and plastic cone
in wall shuttering complete as per the direction of
Engineer-in-charge.
5.10.1 12 mm dia. & 100 mm length 1.00 sets 156.05 Each Set 156.00
5.10.2 12 mm dia. & 150 mm length 1.00 sets 170.25 Each Set 170.00
5.10.3 20 mm dia. & 150 mm length 1.00 sets 184.50 Each Set 185.00
5.10.4 20 mm dia.& 225 mm length 1.00 sets 201.55 Each Set 202.00
5.11 Extra for additional height in centering, shuttering
where ever required with adequate bracing, propping
etc., including cost of de-shuttering and decentering at
all levels, over a height of 3.5 m, for every additional
height of 1 metre or part thereof (Plan area to be
measured).

5.11.1 Suspended floors, roofs, landing, beams and balconies 1.00 Sqm 384.30 One Square 384.00
(Plan area to be measured) Metre
5.12 Providing, hoisting and fixing above plinth level up to 1.00 Cum 10585.90 One Cubic 10586.00
floor five level precast reinforced cement concrete work Metre
in string courses, bands, copings, bed plates, anchor
blocks, plain window sills and the like, including the cost
of required centering, shuttering but, excluding cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) derived from natural sources : 3 graded
stone aggregate 20 mm nominal size derived from
natural sources).

DSR - 2023 IN MS EXCEL Page 19 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.12A Providing, hoisting and fixing above plinth level up to 1.00 Cum 10416.75 One Cubic 10417.00
floor five level precast reinforced cement concrete work Metre
in string courses, bands, copings, bed plates, anchor
blocks, plain window sills and the like, including the cost
of required centering, shuttering but, excluding cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand
incuding manufactured sand derived from Recycled
Concrete Aggregate (RCA) upto 20% : 3 graded stone
aggregate 20 mm nominal size Recycled Concrete
Aggregate (RCA) upto 20%).

5.13 Providing, hoisting and fixing up to floor five level 1.00 Cum 14325.95 One Cubic 14326.00
precast reinforced cement concrete in small lintels not Metre
exceeding 1.5m clear span up to floor five level,
including the cost of required centering, shuttering but,
excluding the cost of reinforcement, with 1:1.5:3 (1
cement : 1.5 coarse sand(zone- III) derived from natural
sources : 3 graded stone aggregate 20 mm nominal size
derived from natural sources ).

5.13A Providing, hoisting and fixing up to floor five level 1.00 Cum 14155.35 One Cubic 14155.00
precast reinforced cement concrete in small lintels not Metre
exceeding 1.5m clear span up to floor five level,
including the cost of required centering, shuttering but,
excluding the cost of reinforcement, with 1:1.5:3 (1
cement : 1.5 coarse sand incuding manufactured sand
derived from Recycled Concrete Aggregate (RCA) upto
20% : 3 graded stone aggregate 20 mm nominal size
including Recycled Concrete Aggregate (RCA) upto
20%).

5.14 Providing, hoisting and fixing above plinth level up to 1.00 Cum 18234.95 One Cubic 18235.00
floor five level precast reinforced cement concrete in Metre
mouldings as in cornices, windows sills etc, including
setting in cement mortar 1:3 (1 cement : 3 coarse sand)
cost of required centering, shuttering but, excluding the
cost of reinforcement, with 1:1.5:3 (1 cement : 1.5
coarse sand(zone- III)derived from natural sources : 3
graded stone aggregate 20 mm nominal size derived
from natural sources ).

5.14A Providing, hoisting and fixing above plinth level up to 1.00 Cum 18064.15 One Cubic 18064.00
floor five level precast reinforced cement concrete in Metre
mouldings as in cornices, windows sills etc, including
setting in cement mortar 1:3 (1 cement : 3 coarse sand)
cost of required centering, shuttering but, excluding the
cost of reinforcement, with 1:1.5:3 (1 cement : 1.5
coarse sand incuding manufactured sand derived from
Recycled Concrete Aggregate (RCA) upto 20% : 3 graded
stone aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20%).

5.15 Providing, transporting, hoisting and fixing above plinth 1.00 Cum 13899.20 One Cubic 13899.00
level up to floor five level precast reinforced cement Metre
concrete in lintels, beams and bressumers, including
setting in cement mortar 1:3 (1 cement : 3 coarse sand),
cost of required centering and shuttering but, excluding
the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5
coarse sand(zone- III)derived from natural sources : 3
graded stone aggregate 20 mm nominal size derived
from natural sources ).

DSR - 2023 IN MS EXCEL Page 20 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.15A Providing, transporting, hoisting and fixing above plinth 1.00 Cum 13728.40 One Cubic 13728.00
level up to floor five level precast reinforced cement Metre
concrete in lintels, beams and bressumers, including
setting in cement mortar 1:3 (1 cement : 3 coarse sand),
cost of required centering and shuttering but, excluding
the cost of reinforcement, with 1:1.5:3(1 cement : 1.5
coarse sand incuding manufactured sand derived from
Recycled Concrete Aggregate (RCA) upto 20% : 3 graded
stone aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20%).

5.16 Providing, transporting, hoisting and fixing above plinth 1.00 Cum 20355.80 One Cubic 20356.00
level up to floor five level precast reinforced cement Metre
concrete in shelves, including setting in cement mortar
1:3 (1 cement : 3 coarse sand), cost of required
centering, shuttering and finishing with neat cement
punning on exposed surfaces but, excluding the cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand
(zone- III) derived from natural sources : 3 graded stone
aggregate 20 mm nominal size derived from natural
sources ).

5.16A Providing, transporting, hoisting and fixing above plinth 1.00 Cum 20185.00 One Cubic 20185.00
level up to floor five level precast reinforced cement Metre
concrete in shelves, including setting in cement mortar
1:3 (1cement : 3 coarse sand), cost of required
centering, shuttering and finishing with neat cement
punning on exposed surfaces but, excluding the cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand
including manufactured sand derived from Recycled
Concrete Aggregate (RCA) upto 20% : 3 graded stone
aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20%).

5.17 Providing, transporting, hoisting and fixing above plinth 1.00 Cum 12043.35 One Cubic 12043.00
level up to floor five level precast reinforced cement Metre
concrete in vertical & horizontal fins, individually or
forming box louvers, setting in cement mortar 1:2 (1
cement : 2 coarse sand), including the cost of required
centering, shuttering but, excluding the cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone- III)derived from natural sources : 3 graded
stone aggregate 20 mm nominal size derived from
natural sources ).

5.17A Providing, transporting, hoisting and fixing above plinth 1.00 Cum 11872.55 One Cubic 11873.00
level up to floor five level precast reinforced cement Metre
concrete in vertical & horizontal fins, individually or
forming box louvers, setting in cement mortar 1:2 (1
cement : 2 coarse sand), including the cost of required
centering, shuttering but, excluding the cost of
reinforcement, with 1:1.5:3(1 cement : 1.5 coarse sand
incuding manufactured sand derived from Recycled
Concrete Aggregate (RCA) upto 20% : 3 graded stone
aggregate 20 mm nominal size including Recycled
Concrete Aggregate (RCA) upto 20%).

DSR - 2023 IN MS EXCEL Page 21 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.18 Providing precast cement concrete Jali 1:2:4 (1 cement :
2 coarse sand(zone-III) : 4 graded stone aggregate 6mm
nominal size ), reinforced with 1.6 mm dia mild steel
wire, including centering and shuttering, roughening
cleaning, fixing and finishing in cement mortar 1:3 (1
cement: 3 fine sand) etc. complete, excluding plastering
of the jambs, sills and soffits.

5.18.1 50 mm thick 1.00 Sqm 1886.90 One Square 1887.00

Metre
5.18.2 40 mm thick 1.00 Sqm 1706.55 One Square 1707.00
Metre
5.18.3 25 mm thick 1.00 Sqm 1539.00 One Square 1539.00
Metre
5.19 Encasing rolled steel sections, in beams and columns, 1.00 Cum 16089.40 One Cubic 16089.00
with cement concrete 1:1.5:3 (1 cement : 1.5 coarse Metre
sand(zone-III)derived from natural sources : 3 graded
stone aggregate 20 mm nominal size derived from
natural resources ), including centering and shuttering
complete but, excluding cost of reinforcement.

5.19A Encasing rolled steel sections, in beams and columns, 1.00 Cum 15918.60 One Cubic 15919.00
with cement concrete 1:1.5:3 (1 cement : 1.5 coarse Metre
sand incuding manufactured sand derived from
Recycled Concrete Aggregate (RCA) upto 20% : 3 graded
stone aggregate 20 mm nominal size Recycled Concrete
Aggregate (RCA) upto 20%), including centering and
shuttering complete but, excluding cost of
reinforcement.

5.20 Encasing rolled steel section in grillages with cement 1.00 Cum 9663.25 One Cubic 9663.00
concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone- Metre
III)derived from natural sources : 3 graded stone
aggregate 20 mm nominal size derived from natural
sources ) including centering and shuttering but,
excluding cost of expanded metal and hangers.

5.20A Encasing rolled steel section in grillages with cement 1.00 Cum 9492.45 One Cubic 9492.00
concrete 1:1.5:3(1 cement : 1.5 coarse sand incuding Metre
manufactured sand derived from Recycled Concrete
Aggregate (RCA) upto 20% : 3 graded stone aggregate
20 mm nominal size Recycled Concrete Aggregate (RCA)
upto 20%), including centering and shuttering but,
excluding cost of expanded metal and hangers.

5.21 Extra for providing and fixing expanded metal mesh of 1.00 Sqm 485.05 One Square 485.00
size 20x60 mm and strands 3.25 mm wide 1.6 mm thick Metre
weighing 3.64 kg per sqm for encasing of rolled steel
sections in beams, columns and grillages, excluding cost
of hangers.

5.22 Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position and
binding all complete upto plinth level.
5.22.1 Mild steel and Medium Tensile steel bars 1.00 Kg 107.10 One Kilogram 107.00

5.22.2 Hard drawn steel wire 1.00 Kg 95.80 One Kilogram 96.00

5.22.3 Cold twisted bars 1.00 Kg 107.85 One Kilogram 108.00

5.22.4 Hot rolled deformed bars 1.00 Kg 107.85 One Kilogram 108.00

DSR - 2023 IN MS EXCEL Page 22 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.22.5 Hard drawn steel wire fabric 1.00 Kg 102.20 One Kilogram 102.00

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or 1.00 Kg 107.85 One Kilogram 108.00
more.
5.22A Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete above plinth level.
5.22A.1 Mild steel and Medium Tensile steel bars 1.00 Kg 107.10 One Kilogram 107.00

5.22A.2 Hard drawn steel wire 1.00 Kg 95.80 One Kilogram 96.00

5.22A.3 Cold twisted bars 1.00 Kg 107.85 One Kilogram 108.00

5.22A.4 Hot rolled deformed bars 1.00 Kg 107.85 One Kilogram 108.00

5.22A.5 Hard drawn steel wire fabric 1.00 Kg 102.20 One Kilogram 102.00

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or 1.00 Kg 107.85 One Kilogram 108.00
more.
5.22B Steel reinforcement for R.C.C. work ready to use "cut
and bend" rebars of approved make from
factory/workshop to construction site including placing
in position and binding all complete upto plinth level.

5.22B.1 Thermo-Mechanically Treated bars of grade Fe-500D or 1.00 Kg 99.65 One Kilogram 100.00
more.
5.22C Steel reinforcement for R.C.C. work ready to use "cut
and bend" rebars of approved make from
factory/workshop to construction site including placing
in position and binding all complete above plinth level.

5.22C.1 Thermo-Mechanically Treated bars of grade Fe-500D or 1.00 Kg 99.65 One Kilogram 100.00
more.
5.23 Smooth finishing of the exposed surface of R.C.C. work 1.00 Sqm 300.45 One Square 300.00
with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine Metre
sand).
5.24 Extra for rendering smooth the top of suspended floors, 1.00 Sqm 150.50 One Square 151.00
landings and staircases (treads and risers) with cement Metre
mortar 1:2 (1 cement : 2 coarse sand), including a
floating coat of neat cement and protecting the surface
with a layer of 7.5 cm of earth laid over 15 mm of fine
sand in case of suspended floor and bricks laid in mud
mortar in case of landings and steps, including
subsequent removal and cleaning of the same.

5.25 Providing and fixing in position copper plate as per 1.00 Kg 811.85 One Kilogram 812.00
design for expansion joints.
5.26 Providing and filling in position, blown bitumen in 1.00 Cum 74854.65 One Cubic 74855.00
expansion joints. Metre
5.27 Providing and filling in position bitumen mix filler of 1.00 Cum 28212.60 One Cubic 28213.00
proportion 80 kg. of hot bitumen, 1 kg. of cement and Metre
0.25 cubic metre of coarse sand for expansion joints.

5.28 Providing and fixing in position 12mm thick bitumen 1.00 units 655.75 per cm depth 656.00
impregnated fiber board conforming to IS: 1838, per 100m
including cost of primer, sealing compound Grade-A in
expansion joints.

5.29 Providing and fixing sheet covering over expansion

joints with iron screws as per design.

DSR - 2023 IN MS EXCEL Page 23 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.29.1 Non-asbestos 6 mm thick fibre cement board, Type-A,
Category-Ill as per IS: 14862:2000
5.29.1.1 150mm wide 1.00 m 245.45 One Metre 245.00
5.29.1.2 200mm wide 1.00 m 330.20 One Metre 330.00
5.29.2 Aluminium fluted strips 3.15 mm thick.
5.29.2.1 150 mm wide 1.00 m 567.60 One Metre 568.00
5.29.2.2 200 mm wide 1.00 m 753.85 One Metre 754.00
5.29.3 Cement bonded wood particle board 6mm thick as per
IS : 14276
5.29.3.1 150 mm wide 1.00 m 237.40 One Metre 237.00
5.29.3.2 200 mm wide 1.00 m 319.40 One Metre 319.00
5.30 Add for plaster drip course/ groove in plastered surface 1.00 m 78.40 One Metre 78.00
or moulding to R.C.C. projections
5.31 Extra for laying reinforced cement concrete in or under
water and/ or liquid mud, including cost of pumping or
bailing out water and removing slush etc., complete.

Note For above Item 5.31 :- The quantity will be 1.00 Cum 1098.80 One Cubic 1099.00
calculated by multiplying the depth measured from the Metre
subsoil water level up to the centre of gravity of the
R.C.C. under subsoil water with the quantity of R.C.C. in
cubic metre executed under subsoil water. The depth of
centre of gravity shall be reckoned correct to 0.1 m
(0.05 m or more shall be taken as 0.1 m and less than
0.05 m ignored). No extra payment shall be made for
placing reinforcement or centering & shuttering under
sub - soil water conditions.

5.32 Extra for laying reinforced cement concrete in or under 1.00 Cum 467.55 One Cubic 468.00
foul positions. Metre
5.33 Providing and laying in position ready mixed or site
batched design mix cement concrete for reinforced
cement concrete work; using coarse aggregate and fine
aggregate derived from natural sources, Portland
Pozzolana / Ordinary Portland /Portland Slag cement,
admixtures in recommended proportions as per IS:
9103 to accelerate / retard setting of concrete, to
improve durability and workability without impairing
strength; including pumping of concrete to site of
laying, curing, carriage for all leads; but excluding the
cost of centering, shuttering, finishing and
reinforcement as per direction of the engineer-in-
charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be payable
separately. In case the cement content in design mix is
more than 110% of the specified minimum cement
content, the contractor shall have discretion to either
re-design the mix or bear the cost of extra cement

5.33.1 All works upto plinth level

5.33.1.1 Concrete of M25 grade with minimum cement content 1.00 Cum 9504.75 One Cubic 9505.00
of 330 kg /cum Metre
5.33.1.2 Concrete of M30 grade with minimum cement content 1.00 Cum 9655.70 One Cubic 9656.00
of 350 kg /cum Metre
5.33.1.3 Concrete of M35 grade with minimum cement content 1.00 Cum 9806.70 One Cubic 9807.00
of 370 kg /cum Metre

DSR - 2023 IN MS EXCEL Page 24 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.33.1.4 Concrete of M40 grade with minimum cement content 1.00 Cum 9957.65 One Cubic 9958.00
of 390 kg /cum Metre
5.33.1.5 Concrete of M50 grade with minimum cement content 1.00 Cum 10108.65 One Cubic 10109.00
of 410 kg /cum Metre
5.33.2 All works above plinth level upto floor V level
5.33.2.1 Concrete of M25 grade with minimum cement content 1.00 Cum 9860.40 One Cubic 9860.00
of 330 kg /cum Metre
5.33.2.2 Concrete of M30 grade with minimum cement content 1.00 Cum 10011.35 One Cubic 10011.00
of 350 kg /cum Metre
5.33.2.3 Concrete of M35 grade with minimum cement content 1.00 Cum 10162.35 One Cubic 10162.00
of 370 kg /cum Metre
5.33.2.4 Concrete of M40 grade with minimum cement content 1.00 Cum 10313.30 One Cubic 10313.00
of 390 kg /cum Metre
5.33.2.5 Concrete of M50 grade with minimum cement content 1.00 Cum 10464.30 One Cubic 10464.00
of 410 kg /cum Metre
5.33A Providing and laying in position ready mixed or site
batched design mix cement concrete for reinforced
cement concrete work; using coarse aggregate and fine
aggregate derived from natural sources and using
recycled concrete aggregate (RCA) as coarse aggregate
and fine aggregate within permissible utilization of 20%
each, Portland Pozzolana /Ordinary Portland/Portland
Slag cement, admixtures in recommended proportions
as per IS: 9103 to accelerate / retard setting of
concrete, to improve durability and workability without
impairing strength; including pumping of concrete to
site of laying, curing, carriage for all leads; but excluding
the cost of centering, shuttering, finishing and
reinforcement as per direction of the engineer-in-
charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be payable
separately. In case the cement content in design mix is
more than 110% of the specified minimum cement
content, the contractor shall have discretion to either
re-design the mix or bear the cost of extra cement

5.33A.1 All works upto plinth level

5.33A.1.1 Concrete of M25 grade with minimum cement content 1.00 Cum 9333.95 One Cubic 9334.00
of 330 kg /cum Metre
5.33A.2 All works above plinth level upto floor V level
5.33A.2.1 Concrete of M25 grade with minimum cement content 1.00 Cum 9689.60 One Cubic 9690.00
of 330 kg /cum Metre
5.35 Add for using extra cement in the items of design mix 1.00 Qtl 733.50 One Quintal 734.00
over and above the specified cement content therein.

DSR - 2023 IN MS EXCEL Page 25 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.36 Providing and placing in position precast reinforced 1.00 Cum 33018.75 One Cubic 33019.00
cement concrete waffle units, square or rectangular, as Metre
per design and shape for floors and roofs in 1:1½:3 (1
Cement : 1½ coarse sand (zone-III)derived from natural
sources : 3 graded stone aggregate 10 mm nominal size
derived from natural sources), including flush or deep
ruled pointing at joints in Cement mortar 1:2 (1 Cement
: 2 Fine sand), making necessary holes of required sizes
for carrying through service lines etc., providing steel
hooks for lifting etc, form work in precasting, handling,
hoisting, centering and erection complete for all floor
levels but, excluding the cost of reinforcement.

5.36A Providing and placing in position precast reinforced 1.00 Cum 32847.95 One Cubic 32848.00
cement concrete waffle units, square or rectangular, as Metre
per design and shape for floors and roofs in 1:1½:3 (1
cement : 1.5 coarse sand incuding manufactured sand
derived from Recycled Concrete Aggregate (RCA) upto
20% : 3 graded stone aggregate 10 mm nominal size
including Recycled Concrete Aggregate (RCA) upto
20%), including flush or deep ruled pointing at joints in
Cement mortar 1:2 (1 Cement : 2 Fine sand), making
necessary holes of required sizes for carrying through
service lines etc., providing steel hooks for lifting etc,
form work in precasting, handling, hoisting, centering
and erection complete for all floor levels but, excluding
the cost of reinforcement.

5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level 1.00 Cum 355.65 One Cubic 356.00
for each four floors or part thereof. Metre
5.41 Supplying and applying pre tested and approved water
based concrete curing compound to concrete/ masonry
surface, all as per manufacturer’s specification and
direction of Engineer-in-charge.

5.41.1 Non pigmented wet curing compound 1.00 Sqm 69.05 One Square 69.00
Metre
5.42 Providing and fixing parallel threaded couplers
conforming to IS code on “Reinforcement Couplers for
Mechanical Splices of Bars for Concrete Reinforcement
- Specification”, to reinforcement bars including
threading, enlargement at connection by forging,
protecting the prepared reinforcement bars and related
operations as required to complete the works per
direction of Engineer- in-Charge.

5.42.1 Coupler for 16 mm diameter reinforcement bar 1.00 No. 115.10 Each 115.00
5.42.2 Coupler for 20 mm diameter reinforcement bar 1.00 No. 160.10 Each 160.00
5.42.3 Coupler for 25 mm diameter reinforcement bar 1.00 No. 228.95 Each 229.00
5.42.4 Coupler for 28 mm diameter reinforcement bar 1.00 No. 267.55 Each 268.00
5.42.5 Coupler for 32 mm diameter reinforcement bar 1.00 No. 318.80 Each 319.00
5.43 Providing and fixing in position Stainless steel Grade
304 plate-1.0 mm thick as per design for expansion
joints.
5.43.1 200 mm wide. 1.00 m 859.75 One Metre 860.00
5.43.2 300 mm wide. 1.00 m 1208.05 One Metre 1208.00

DSR - 2023 IN MS EXCEL Page 26 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.44 Providing and fixing of expansion joint system related
with floor location as per drawings and direction of
Engineer-In-Charge. The joints system will be of
extruded aluminum base members, self aligning / self
centering arrangement and support plates etc. as per
ASTM B221-02. The system shall be such that it
provides floor to floor /floor to wall expansion control
system for various vertical location in load application
areas that accommodates multi directional seismic
movement without stress to it's components. System
shall consist of metal profiles with a universal aluminum
base member designed to accommodate various
project conditions and finish floor treatments.

The cover plate shall be designed of width and

thickness required to satisfy projects movement and
loading requirements and secured to base members by
utilizing manufacturer’s pre-engineered self- centering
arrangement that freely rotates / moves in all
directions. The Self - centering arrangement shall
exhibit circular sphere ends that lock and slide inside
the corresponding aluminum extrusion cavity to allow
freedom of movement and flexure in all directions
including vertical displacement. Provision of Moisture
Barrier Membrane in the Joint System to have
watertight joint is mandatory requirement all as per the
manufactures design and as approved by Engineer -in-
Charge. (Material shall confirm to ASTM 6063).

5.44.1 Floor Joint of 100 mm gap 1.00 m 6392.55 One Metre 6393.00
5.44.2 Floor Joint of 150 mm gap 1.00 m 7812.35 One Metre 7812.00
5.44.3 Floor Joint of 200 mm gap 1.00 m 9903.65 One Metre 9904.00
5.45 Providing and fixing of expansion joint system related
with wall joint (internal/external) location as per
drawings and direction of Engineer-In- Charge.The
joints shall be of extruded aluminum base members,
self aligning /centering arrangement and support plates
as per ASTM B221- 02. The material shall be such that it
provides an Expansion Joints System suitable for
vertical wall to wall/ wall to corner application, both
new and existing construction in office Buildings &
complexes with no slipping down tendency amongst
the components of the Joint System. The Joint System
shall utilize light weight aluminum profiles exhibiting
minimal exposed aluminum surfaces mechanically snap
locking the multicellular to facilitate movement.
(Material shall confirm to ASTM 6063).

5.45.1 Wall Joint of 100 mm gap 1.00 m 5305.65 One Metre 5306.00
5.45.2 Wall Joint of 150 mm gap 1.00 m 5981.40 One Metre 5981.00
5.45.3 Wall Joint of 200 mm gap 1.00 m 6889.05 One Metre 6889.00

DSR - 2023 IN MS EXCEL Page 27 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.46 Providing and fixing of expansion joint system of
approved make and manufactures for various roof
locations as per approved drawings and direction of
Engineer-In-Charge. The joints shall be of extruded
aluminum base members with, self aligning and self
centering arragement support plates asper ASTM B221-
02. The system shall be such that it provides watertight
roof to roof/roof to corner joint cover expansion
control system that is capable of accommodating
multidirectional seismic movement without stress to its
components. System shall consist of metal profile that
incorporates an universal aluminum base member
designed to accommodate various project conditions
and roof treatments. The cover plate shall be designed
of width and thickness required to satisfy movement
and loading requirements and secured to base
members by utilizing manufacturer’s pre-engineered
self-centering arrangement that freely rotates / moves
in all directions.

The Self centering arrangement shall exhibit circular

sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow
freedom of movement and flexure in all directions
including vertical displacement. The Joint System shall
resists damage or deterioration from the impact of
falling ice, exposure to UV, airborne contaminants and
occasional foot traffic from maintenance personnel.
Provision of Moisture Barrier Membrane in the Joint
System to have water tight joint is mandatory
requirement. (Material shall confirm to ASTM 6063.)

5.46.1 Roof Joint of 100 mm gap 1.00 m 5985.70 One Metre 5986.00
5.46.2 Roof Joint of 150 mm gap 1.00 m 6699.85 One Metre 6700.00
5.46.3 Roof Joint of 200 mm gap 1.00 m 7927.60 One Metre 7928.00
5.47 Providing and fixing in position factory made precast
RCC M-40 door and window frame fixing with hold fast
embedded in 1:3:6 concrete block having excellent
smooth finish as per IS: 6523 with reinforcement of 3
Nos, 6 mm dia main bars tied with 3 mm M.S stirrups
placed @ 200 mm C/C and 6 numbers high strength
polymer blocks of required size for fixing hinges
including providing 6 no specially designed M.S.
galvanised sleeves for accomodating 6 mm dia fully
threaded bolts for fixing hold fast on vertical members,
providing suitable arrangement for recieving sliding
door bolts and tower bolt etc all complete, as per the
direction of Engineer in charge. The frame shall be
measured in running metre correct to two places of
decimal.

5.47.1 Door frame 125 mmx 60 mm 1.00 m 814.85 One Metre 815.00
5.47.2 Door frame 100 mmx 60 mm 1.00 m 757.10 One Metre 757.00
5.47.3 Door frame 85 mmx60 mm 1.00 m 727.30 One Metre 727.00

DSR - 2023 IN MS EXCEL Page 28 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
5.48 Providing and laying Reinforced cement concrete for
construction of piers, abutments, portal frames, pier
caps and bearing pedestals and seismic arresters over
pier/ abutment caps at all locations with specified grade
using Ordinary Portland Cement (conforming to
strength requirement of IS:8112) including the cost of
steel centering and shuttering etc. complete including
testing of materials etc. for casting pier & pier cap in
one/two stage, necessary tools, plants, machinery and
all related operations as required to complete the work
as per drawings and Specifications with all leads, lifts
and depths true to level and position but excluding the
cost of providing reinforcement. Reinforcement shall be
measured and paid separately.

Note:- Cement content considered in this item is 480

Kg/ Cum. Excess/ less cement used as per design mix is
payable/ recoverable separately.
5.48.1 Reinforced Cement Concrete -M-50 1.00 Cum 8509.95 One Cubic 8510.00
Metre
5.48.2 Reinforced Cement Concrete -M-60 1.00 Cum 9500.30 One Cubic 9500.00
Metre
5.48.3 Extra for using M -50/ M-60 Grade Self-compacting 1.00 Cum 664.85 One Cubic 665.00
Cement Concrete Metre
5.49 Constructing cast-in situ RCC diaphragm wall by
providing and laying machine batched, machine mixed,
self compacting, ready mix reinforced cement concrete,
tramie controlled, of M 30 grade using minimum 400kg.
cement per cum of concrete including providing and
mixing required admixtures in recommended
proportions as per IS : 9103, as approved by the
Engineer-in-charge, for achieving 150- 200mm slump,
for diaphragm wall having thickness as per approved
structural design not exceeding 600 mm, in pannels of
required depth and lengths as per approved drawing,
including constructing necessary guide walls as required
and as specified including boring in all kinds of soils and
rocks,including working in or under water and / or
liquid mud

in foul conditions and pumping or bailing out of water

and removing slush, including disposal of earth/ rock /
slush etc. for all leads and all lifts, including preparing,
providing and re-circulating bentonite slurry in the
trench as and when required for all depths, including
agitating bentonite slurry during trenching etc.,
providing and fixing stop ends or form tubes, upto the
required depth of diaphragm wall including extracting
the same after casting including chipping off the
bentonite adulterated concrete or unsound concrete up
to the cut off level for obtaining the sound concrete,
dressing undulations on the exposed face of diaphragm
wall after excavation by chipping / chiseling etc.
including filling the depression/ cavities with sound
concrete etc. complete and as directed by the Engineer-
in-charge,

DSR - 2023 IN MS EXCEL Page 29 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
including providing recess for bearing plates and fixing
insert boxes for inclined rock anchors etc. complete as
per the specifications and approved design and as
directed by the Engineer-in-charge, but excluding the
cost of reinforcement and inserts.

(rates include cost of all inputs of labour, material and

T&P, cost of handling, lifting & placing in position the
reinforcement bars etc. involved in the work and all
other incidental expenditure for completing the work
aas directed by the Engineer-in-charge), However, the
actual area of the diaphragm wall, correct to two places
of decimal, from design bottom level to the design cut
off level (including portion anchored in the rock upto
the design bottom level) only shall be measured for
payment.

Excess/less cement used for design mix including the 1.00 Cum 20460.45 One Cubic 20460.00
extra cement required for under water concreting is Metre
payable / recoverable seperately.
Total of the Sub-Head - Reinforced Cement Concrete : 839767.00
Sub-Head : Masonry Work
6.1 Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in foundation
and plinth in:
6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 7370.65 One Cubic 7371.00
Metre
6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 7132.25 One Cubic 7132.00
Metre
6.2 Brick work with common burnt clay modular bricks of
class designation 7.5 in foundation and plinth in:
6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 6504.90 One Cubic 6505.00
Metre
6.2.2 Cement Mortar 1:6 (1 cement : 6 coarse sand). 1.00 Cum 6295.15 One Cubic 6295.00
Metre
6.3 Brick work with common burnt clay machine moulded
perforated bricks of class designation 12.5 conforming
to IS: 2222 in superstructure above plinth level up to
floor five level in cement mortar 1:6 (1 cement : 6
coarse sand) :

6.3.1 With F.P.S.(non modular) bricks. 1.00 Cum 9299.90 One Cubic 9300.00
Metre
6.3.2 With Modular bricks. 1.00 Cum 8942.35 One Cubic 8942.00
Metre
6.4 Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in
all shapes and sizes in :

6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 9344.35 One Cubic 9344.00
Metre
6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 9105.95 One Cubic 9106.00
Metre
6.5 Extra for brick work / AAC block masonry / Tile brick 1.00 Cum 169.45 One Cubic 169.00
masonry in superstructure above floor V level, for each Metre
four floors or part thereof by mechanical means.

DSR - 2023 IN MS EXCEL Page 30 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
6.6 Extra for forming cavity 5 cm to 11.5 cm wide in cavity 1.00 Sqm 234.20 One Square 234.00
walls with necessary weep and vent holes including use Metre
of cores and cost of providing and fixing bitumastic
coated M .S. ties 300 mm long of 25x 3 mm section at
not less than 3 ties per sqm as per approved design.

6.7 Providing half brick masonry with common burnt clay 1.00 m 300.75 One Metre 301.00
F.P.S. (non modular) bricks of class designation 7.5 in
cement mortar 1:3 (1 Cement : 3 coarse sand) in
superstructure for closing cavity 5 to 7.5 cm wide in
cavity wall complete with 10cm / 11.4 cm wide bitumen
felt type 3 grade 1.

6.8 Brick work 7 cm thick with common burnt clay F.P.S. 1.00 Sqm 865.65 One Square 866.00
(non modular) brick of class designation 7.5 in cement Metre
mortar 1:3 (1 cement : 3 coarse sand) in superstructure
above plinth level and upto floor five level.

6.9 Brick work in plain arches in superstructure above 1.00 Cum 15077.95 One Cubic 15078.00
plinth level and upto floor five level including centering Metre
and shuttering complete for span up to 6 metres with
common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 in cement mortar 1:3 (1 cement : 3
coarse sand).

6.10 Brick work in gauged arches in sperstructure above 1.00 Cum 19066.10 One Cubic 19066.00
plinth level and upto floor five level in cement mortar Metre
1:3 (1 cement : 3 coarse sand) including centering and
shuttering complete, for span up to 6 meters with
common burnt clay F.P.S. (non modular) bricks of class
designation 7.5.

6.11 Extra for additional cost of centering for arches 1.00 Sqm 608.15 One Square 608.00
exceeding 6m span including all shuttering, bolting, Metre
wedging and removal (Area of the soffit to be
measured).

6.12 Half brick masonry with common burnt clay F.P.S. (non
modular) bricksof class designation 7.5 in foundations
and plinth in :
6.12.1 Cement mortar 1:3 (1 cement : 3 coarse sand) 1.00 Sqm 931.75 One Square 932.00
Metre
6.12.2 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Sqm 905.05 One Square 905.00
Metre
6.13 Half brick masonry with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level.
6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) 1.00 Sqm 1150.50 One Square 1151.00
Metre
6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 1.00 Sqm 1123.80 One Square 1124.00
Metre
6.14 Extra for half brick masonry in superstructure, above 1.00 Sqm 15.00 One Square 15.00
floor V level for every four floors or part thereof by Metre
mechanical means.
6.15 Extra for providing and placing in position 2 Nos 6mm 1.00 Sqm 104.80 One Square 105.00
dia. M.S. bars at every third course of half brick Metre
masonry.ird course of half brick masonry.
6.16 Tile brick masonry with common burnt clay F.P.S. (non
modular) tile bricks of class designation 10 in
foundation and plinth in:
6.16.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 11212.50 One Cubic 11213.00
Metre

DSR - 2023 IN MS EXCEL Page 31 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
6.16.2 Cement mortar 1:6 (1 cement : 6 coarse sand). 1.00 Cum 10831.05 One Cubic 10831.00
Metre
6.17 Tile brick masonry with common burnt clay machine 1.00 Cum 11328.50 One Cubic 11329.00
moulded tile bricks of class designation 12.5 conforming Metre
to IS : 2690 (Part I) in foundation and plinth in cement
mortar 1:6 (1 cement : 6 coarse sand).

6.18 Tile brick masonry with common burnt clay F.P.S. (non 1.00 Cum 12883.05 One Cubic 12883.00
modular) tile bricks of class designation 10 in Metre
superstructure above plinth level up to floor V level in
cement mortar 1:6 (1 cement : 6 coarse sand).

6.20 Tile brick masonry with common burnt clay F.P.S. (non 1.00 Cum 18975.15 One Cubic 18975.00
modular) tile bricks of class designation 10 in plain arch Metre
work in superstructure above plinth and upto floor five
level in cement mortar 1:4 (1 cement : 4 coarse sand)
including centering and shuttering complete.

6.21 Tile brick masonry with common burnt clay F.P.S. (non 1.00 Cum 23019.75 One Cubic 23020.00
modular) tile bricks of class designation 10 in gauged Metre
arch work in superstructure above plinth and upto floor
five level in cement mortar 1:4 (1 cement : 4 coarse
sand) including centering and shuttering complete.

6.22 Tile brick masonry work 5 cm thick with common burnt 1.00 Sqm 885.45 One Square 885.00
clay F.P.S. (non modular) tile bricks of class designation Metre
10 in cement mortar 1:3 (1 cement : 3 coarse sand) in
superstructure above plinth and upto floor five level.

6.23 Honey-comb brick work 10 / 11.4 cm thick with 1.00 Sqm 711.50 One Square 712.00
common burnt clay bricks of class designation 7.5 in Metre
super structure above plinth level upto floor V level
with cement mortar 1:4 (1 cement : 4 coarse sand).

6.25 Extra for laying brick work in or under foul position. 1.00 Cum 467.55 One Cubic 468.00
Metre
6.26 Brick work with common burnt clay selected F.P.S. (non
modular) bricks of class designation 7.5 in exposed brick
work including making horizontal and vertical grooves
10 mm wide 12 mm deep complete in cement mortar
1:6 (1 cement : 6 coarse sand)

6.26.1 From ground level upto plinth level 1.00 Cum 7361.35 One Cubic 7361.00
Metre
6.26.2 Above plinth level upto floor V level. 1.00 Cum 9439.75 One Cubic 9440.00
Metre
6.27 Brick work with common burnt clay modular bricks of
class designation 7.5 in exposed brick work including
making horizontal and vertical grooves 10mm wide 12
mm deep complete in cement mortar 1:6 (1 cement : 6
coarse sand).

6.27.1 From ground level upto plinth level. 1.00 Cum 6339.20 One Cubic 6339.00
Metre
6.27.2 Above plinth level upto floor V level. 1.00 Cum 8312.90 One Cubic 8313.00
Metre
6.28 Brick work with common burnt clay machine moulded
modular bricks of class designation 12.5 in exposed
brick work including making horizontal and vertical
grooves 10 mm wide 12 mm deep complete in cement
mortar 1:6 (1 cement : 6 coarse sand).

6.28.1 From ground level upto plinth level. 1.00 Cum 6997.40 One Cubic 6997.00
Metre

DSR - 2023 IN MS EXCEL Page 32 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
6.28.2 Above plinth level upto floor V level. 1.00 Cum 8971.10 One Cubic 8971.00
Metre
6.29 Brick work with common burnt clay machine moulded
F.P.S. (non modular) bricks of class designation 12.5 in
exposed brick work including making horizontal and
vertical grooves 10 mm wide 12 mm deepcomplete in
cement mortar 1:6 (1 cement : 6 coarse sand).

6.29.1 From ground level upto plinth level. 1.00 Cum 7581.15 One Cubic 7581.00
Metre
6.29.2 Above plinth level upto floor V level. 1.00 Cum 9481.70 One Cubic 9482.00
Metre
6.30 Brick work with common burnt clay machine moulded
perforated F.P.S. (non modular) bricks of class
designation 12.5 conforming IS : 2222 in exposed brick
work including making horizontal and vertical grooves
10mm wide 12 mm deep complete in cement mortar
1:6 (1 cement : 6 coarse sand).

6.30.1 From ground level upto plinth level. 1.00 Cum 7370.30 One Cubic 7370.00
Metre
6.30.2 Above plinth level upto floor V level. 1.00 Cum 9344.00 One Cubic 9344.00
Metre
6.31 Brick work with common burnt clay machine moulded
perforated modular bricks of class designation 12.5
conforming to IS : 2222 in exposed brick work including
making horizontal and vertical grooves 10 mm wide
12mm deep complete in cement mortar 1:6 (1 cement :
6 coarse sand).

6.31.1 From ground level upto plinth level. 1.00 Cum 7032.05 One Cubic 7032.00
Metre
6.31.2 Above plinth level upto floor V level. 1.00 Cum 9005.75 One Cubic 9006.00
Metre
6.32 Brick work with clay flyash F.P.S. (non modular) brick of
class designation 7.5 in superstructure above plinth
level up to floor five level in :
6.32.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 9333.45 One Cubic 9333.00
Metre
6.32.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 9095.05 One Cubic 9095.00
Metre
6.34 Brick work with non modular fly ash bricks conforming
to IS:12894, class designation 10 average compressive
strength in super structure above plinth level up to floor
V level in :

6.34.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 8962.35 One Cubic 8962.00
Metre
6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) 1.00 Cum 8752.55 One Cubic 8753.00
Metre
6.35 Brick work with modular calcium silicate bricks machine
moulded conforming to IS:4139, class designation 10
average compressive strength in super structure above
plinth level up to floor V level in :

6.35.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 1.00 Cum 9793.75 One Cubic 9794.00
Metre
6.35.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) 1.00 Cum 9583.95 One Cubic 9584.00
Metre

DSR - 2023 IN MS EXCEL Page 33 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
6.36 Brick work with modular extruded brunt fly ash clay
sewer bricks (Conforming to IS: 4885 ) in cement mortar
1:4 (1 cement : 4 coarse sand) in foundation and plinth :

6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) 1.00 Cum 7197.75 One Cubic 7198.00
Metre
6.37 Brick work with modular extruded brunt fly ash clay 1.00 Cum 13427.30 One Cubic 13427.00
sewer bricks (conforming to IS : 4885) in arches in Metre
foundation and plinth in cement mortar 1:3 ( 1 cement :
3 fine sand).

6.38 Providing and laying autoclaved aerated Concrete (AAC) 1.00 Cum 10195.45 One Cubic 10195.00
blocks masonry with 100mm / 125 mm thick with Grade Metre
1 AAC blocks of density 551 to 650 kg/cum conforming
to IS:2185 (Part 3) in super structure above plinth level
up to floor V level in cement mortar 1:4 (1 cement : 4
coarse sand ). The rate includes providing and placing in
position 2 Nos 6 mm dia M.S. bars at every third course
of masonry work.

6.40 Providing and laying Gypsum panel partitions 100 mm 1.00 Sqm 1023.60 One Square 1024.00
thick with water proof Gypsum panels of size Metre
666x500x100 mm, made of calcite phosphor Gypsum
fixed with tongue and groove, jointed with bonding
plaster as per manufacturer’s specifications in
superstructure above plinth level up to floor V level.
Gypsum blocks will have a minimum compressive
strength of 9.3 kg/cm2

6.41 Extra for Gypsum panel Partitions in superstructure 1.00 Sqm 181.15 One Square 181.00
above floor V level for every four floors or part thereof. Metre

6.44 Brick edging 7cm wide 11.4 cm deep to plinth 1.00 m 59.45 One Metre 59.00
protection with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 including
grouting with cement mortar 1:4 (1 cement : 4 fine
sand).

6.45 Half brick masonry with non modular fly ash bricks of
class designation 10, conformingio IS :12894, in super
structure above plinth and upto floor V level.
6.45.1 Cement mortar 1 : 3 (1 cement : 3 coarse sand) 1.00 Sqm 1132.50 One Square 1133.00
Metre
6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) 1.00 Sqm 1105.80 One Square 1106.00
Metre
6.47 Providing and laying autoclaved aerated cement blocks 1.00 Cum 8333.65 One Cubic 8334.00
masonry with 150mm/230mm/300 mm thick AAC Metre
blocks in super structure above plinth level up to floor V
level with RCC band at sill level and lintel level with
approved block laying polymer modified adhesive
mortar all complete as per direction of Engineer-in-
Charge. (The payment of RCC band and reinforcement
shall be made for seperately).

Total of the Sub-Head - Masonry Work : 390279.00

Sub-Head : Stone Work
7.1 Random rubble masonry with hard stone in foundation
and plinth including levelling up with cement concrete
1:6:12 (1 cement : 6 coarse sand : 12 graded stone
aggregate 20mm nominal size) upto plinth level with :

7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand). 1.00 Cum 7311.25 One Cubic 7311.00
Metre

DSR - 2023 IN MS EXCEL Page 34 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
7.2 Random rubble masonry with hard stone in
superstructure above plinth level and upto floor five
level, including leveling up with cement concrete 1:6:12
(1 cement : 6 coarse sand : 12 graded stone aggregate
20mm nominal size) at window sills, ceiling level and
the like.

7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand). 1.00 Cum 9275.45 One Cubic 9275.00
Metre
7.4 Extra for random rubble masonry with hard stone in :

7.4.1 Square or rectangular pillars 1.00 Cum 956.00 One Cubic 956.00
Metre
7.4.2 Circular pillars. 1.00 Cum 2530.60 One Cubic 2531.00
Metre
7.5 Extra for random rubble masonry with hard stone 1.00 Cum 1046.20 One Cubic 1046.00
curved on plan for a mean radius not exceeding 6 m. Metre
7.6 Coursed rubble masonry (first sort) with hard stone in
foundation and plinth with :
7.6.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 8812.05 One Cubic 8812.00
Metre
7.7 Coursed rubble masonry (second sort) with hard stone
in foundation & plinth with :
7.7.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 8198.55 One Cubic 8199.00
Metre
7.8 Coursed rubble masonry with hard stone (first or
second sort) in superstructure above plinth level and
upto floor five level.
7.8.1 Masonry work (first sort) , in cement mortar 1:6 (1 1.00 Cum 10741.60 One Cubic 10742.00
cement : 6 coarse sand) Metre
7.8.2 Masonry work (second sort) , in cement mortar 1:6 (1 1.00 Cum 10128.10 One Cubic 10128.00
cement : 6 coarse sand) Metre
7.10 Extra for coursed rubble masonry with hard stone (first
or second sort) in :
7.10.1 Square or rectangular pillars 1.00 Cum 1060.50 One Cubic 1061.00
Metre
7.10.2 Circular pillars. 1.00 Cum 2874.20 One Cubic 2874.00
Metre
7.11 Extra for coursed rubble masonry with hard stone (first 1.00 Cum 1133.65 One Cubic 1134.00
or second sort) curved on plan for a mean radius not Metre
exceeding 6 m.
7.12 Stone work in plain ashlar in super structure upto floor
five level in cement mortar 1:6 (1 cement : 6 coarse
sand) including pointing with cement mortar 1:2 (1
white cement : 2 stone dust) with an admixture of
pigment matching the stone shade :

7.12.1 One face dressed.

7.12.1.1 Red sand stone 1.00 Cum 68294.00 One Cubic 68294.00
Metre
7.12.1.2 White sand stone 1.00 Cum 82518.00 One Cubic 82518.00
Metre
7.12.2 Both face dressed.
7.12.2.1 Red sand stone. 1.00 Cum 91295.00 One Cubic 91295.00
Metre
7.12.2.2 White sand stone 1.00 Cum 105519.00 One Cubic 105519.00
Metre

DSR - 2023 IN MS EXCEL Page 35 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
7.13 Stone work plain ashlar in arches in super structure
upto floor V level in cement mortar 1:3 (1 cement : 3
coarse sand) including centring, shuttering and pointing
with white cement mortar 1:2 (1 white cement : 2 stone
dust) with an admixture of pigment matching the stone
shade.

7.13.1 One face dressed

7.13.1.1 Red sand stone 1.00 Cum 75263.00 One Cubic 75263.00
Metre
7.13.1.2 White sand stone 1.00 Cum 89487.00 One Cubic 89487.00
Metre
7.13.2 Both face dressed
7.13.2.1 Red sand stone 1.00 Cum 98265.00 One Cubic 98265.00
Metre
7.13.2.2 White sand stone 1.00 Cum 112488.00 One Cubic 112488.00
Metre
7.14 Stone work plain ashlar in domes, in super structure
upto floor V level in cement mortar 1:3 (1 cement : 3
coarse sand) including centring, shuttering and pointing
with white cement mortar 1:2 (1 white cement : 2 stone
dust) with an admixture of pigment matching the stone
shade.

7.14.1 One face dressed

7.14.1.1 Red sand stone 1.00 Cum 114277.00 One Cubic 114277.00
Metre
7.14.1.2 White sand stone 1.00 Cum 128500.00 One Cubic 128500.00
Metre
7.14.2 Both face dressed
7.14.2.1 Red sand stone 1.00 Cum 169953.00 One Cubic 169953.00
Metre
7.14.2.2 White sand stone 1.00 Cum 184177.00 One Cubic 184177.00
Metre
7.15 Stone work ashlar punched (ordinary) in superstructure
upto floor five level in cement mortar 1:6 (1 white
cement : 6 coarse sand) including pointing with cement
mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment matching the stone shade.

7.15.1 One face Punched

7.15.1.1 Red sand stone. 1.00 Cum 64926.00 One Cubic 64926.00
Metre
7.15.1.2 White sand stone. 1.00 Cum 79150.00 One Cubic 79150.00
Metre
7.15.2 Both faced punched
7.15.2.1 Red sand stone. 1.00 Cum 84560.00 One Cubic 84560.00
Metre
7.15.2.2 White sand stone. 1.00 Cum 98784.00 One Cubic 98784.00
Metre
7.16 for Extra stone work, random rubble / coursed rubble 1.00 Cum 169.45 One Cubic 169.00
masonry / ashlar masonry above floor V level for every Metre
four floors or part thereof by mechnical means.

7.17 Extra for plain ashlar or ashlar punched in :

7.17.1 Square or rectangular pillars 1.00 Cum 2896.00 One Cubic 2896.00
Metre
7.18 Extra for stone work; plain ashlar or ashlar punched 1.00 Cum 2014.00 One Cubic 2014.00
curved on plan with a mean radius not exceeding 6 m. Metre

DSR - 2023 IN MS EXCEL Page 36 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
7.19 Extra for additional cost of centering for arches 1.00 Sqm 608.15 One Square 608.00
exceeding 6m span including all strutting, bolting, Metre
wedging etc. and removal (area of soffit to be
measured).

7.20 Stone work ashlar sunk or moulded or sunk and

moulded upto floor five level in cement mortar 1:6 (1
cement : 6 coarse sand) including pointing with white
cement mortar 1:2 (1 white cement : 2 stone dust) with
an admixture of pigment matching the stone shade :

7.20.1 Red sand stone 1.00 Cum 94463.00 One Cubic 94463.00
Metre
7.20.2 White sand stone 1.00 Cum 108686.00 One Cubic 108686.00
Metre
7.21 Extra for stone work ashlar sunk or moulded or sunk
and moulded or carved in :
7.21.1 Triangular or Square or rectangular pillars 1.00 Cum 3779.00 One Cubic 3779.00
Metre
7.21.2 Circular or polygonal pillars 1.00 Cum 10706.00 One Cubic 10706.00
Metre
7.22 Extra for stone work ashlar sunk or moulded in 1.00 units 303.50 per metre per 304.00
cornices. cm girth
7.24 Extra for stone work (veneer work) curved on plan with 1.00 Cum 2896.00 One Cubic 2896.00
a mean radius not exceeding 6 m. Metre
7.26 Providing and fixing stone dowels 10x5x2.50 cm cut to 1.00 No. 54.55 Each 55.00
double wedge shape as per design in cement mortar 1:2
(1 cement : 2 coarse sand) including making the
necessary chases.

7.28 Providing and fixing sloping chajja of stone 40 mm thick

and upto 80 cm wide beyond the wall as measured
along the slope in cement mortar 1:4 (1 cement : 4
coarse sand) with 12mm diameter anchoring steel bar
45 cm long fixed in each stone and supported on and
including with bricks cove in cement mortar 1:4 (1
cement : 4 coarse sand) including pointing in cement
mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment matching the stone shade:

7.28.1 Red sand stone:

7.28.1.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 Sqm 2854.35 One Square 2854.00
class designation 7.5 Metre
7.28.2 White sand stone:
7.28.2.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 Sqm 2932.60 One Square 2933.00
class designation 7.5 Metre
7.29 Providing and fixing horizontal chajja of stone 40 mm
thick and upto 80 cm projection in cement mortar 1:4
(1 cement : 4 coarse sand) including pointing in white
cement mortar 1:2 (1 white cement : 2 stone dust) with
an admixture of pigment matching the stone shade: :

7.29.1 Red sand stone 1.00 Sqm 1833.25 One Square 1833.00
Metre
7.29.2 White sand stone 1.00 Sqm 1901.55 One Square 1902.00
Metre
7.30 30mm red sand stone sun-shade (chisel-dressed) 1.00 Sqm 2159.90 One Square 2160.00
supported on red sand stone brackets, fixed in walls Metre
with cement mortar 1:4 (1 cement : 4 coarse sand)
including finishing complete.

DSR - 2023 IN MS EXCEL Page 37 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
7.31 Providing and fixing red sand stone brackets 1.00 No. 6788.85 Each 6789.00
55x22.5x45cm sunk and moulded including providing
and fixing with 4 Nos. gun metal cramp 25x6mm 30 cm
long and dowel bars 7.5 cm long 6 mm dia as per
design.

7.32 Stone work, plain in copings, cornices, string courses

and plinth courses, upto 75 mm thick in Cement mortar
1:6 (1 cement : 6 coarse sand) including pointing with
white cement mortar 1:2 (1 white cement : 2 stone
dust) with an admixture of pigment matching the stone
shade.

7.32.1 Red sand stone 1.00 Cum 93741.10 One Cubic 93741.00
Metre
7.32.2 White sand stone 1.00 Cum 107965.10 One Cubic 107965.00
Metre
7.33 Providing and fixing stone jali 40mm thick throughout in
cement mortar 1:3 (1 cement : 3 coarse sand) including
pointing in white cement mortar 1:2 (1 white cement :
2 stone dust) with an admixture of pigment, matching
the stone shade, jali slab without any chamfers etc.

7.33.1 Red sand stone 1.00 Sqm 14931.55 One Square 14932.00
Metre
7.33.2 White sand stone 1.00 Sqm 14994.15 One Square 14994.00
Metre
7.34 Extra for laying stone work in or under water and/or 1.00 units 1098.80 cum/ mtr 1099.00
liquid mud including cost of pumping or bailing out depth
water and removing slush etc., complete. (NOTE:-The
quantity will be calculated by multiplying the depth
measured from sub-soil water level upto the centre of
gravity of stone work under sub-water with the
quantity of stone work in cum executed under the sub-
soil water. The depth of centre of gravity shall be
reckoned correct to 0.1m 0.05m or more shall be taken
as 0.1m and less than 0.05m ignored).

7.35 Extra for laying stone work in or under foul position. 1.00 Cum 467.55 One Cubic 468.00
Metre
7.38 Stone tile work for wall lining upto 10 m height with
special adhesive over 12mm thick bed of cement
mortar 1:3 (1 cement : 3 coarse sand) including pointing
in white cement with an admixture of pigment to match
the stone shade.

7.38.1 8mm thick (mirror polished and machine cut edge)

7.38.1.1 Granite stone of any colour and shade. 1.00 Sqm 3094.55 One Square 3095.00
Metre
7.38.1.2 Raj Nagar plain white marble/ Udaipur green marble/ 1.00 Sqm 2766.45 One Square 2766.00
Zebra black marble. Metre
Total of the Sub-Head - Stone Work : 2195632.00
Sub-Head : Cladding Work
8.1 Marble work gang saw cut (polished and machine cut)
of thickness 18 mm for wall lining (veneer work),
backing filled with a grout of average 12 mm thick in
cement mortar 1:3 (1 cement : 3 coarse sand), including
pointing with white cement mortar 1:2 (1 white cement
: 2 marble dust) with an admixture of pigment to match
the marble shade (To be secured to the backing by
means of cramps, which shall be paid for separately)

DSR - 2023 IN MS EXCEL Page 38 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
8.1.1 Raj Nagar Plain white marble/ Udaipur green marble/
Zebra black marble.
8.1.1.1 Area of slab upto 0.50 sqm 1.00 Sqm 5742.55 One Square 5743.00
Metre
8.1.1.2 Area of slab over 0.50 sqm 1.00 Sqm 5938.00 One Square 5938.00
Metre
8.2 Providing and fixing 18 mm thick gang saw cut, mirror
polished, premoulded and prepolished, machine cut for
kitchen platforms, vanity counters, window sills, facias
and similar locations of required size,approved shade,
colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated
with white cement, mixed with matching pigment,
epoxy touch ups, including rubbing, curing, moulding
and polishing to edges to give high gloss finish etc.
complete at all levels.

8.2.1 Raj Nagar Plain white marble/ Udaipur green marble/

Zebra black marble
8.2.1.1 Area of slab upto 0.50 sqm 1.00 Sqm 3414.80 One Square 3415.00
Metre
8.2.1.2 Area of slab over 0.50 sqm 1.00 Sqm 3078.40 One Square 3078.00
Metre
8.2.2 Granite stone slab colour black, Cherry/Ruby red
8.2.2.1 Area of slab upto 0.50 sqm 1.00 Sqm 5413.50 One Square 5414.00
Metre
8.2.2.2 Area of slab over 0.50 sqm 1.00 Sqm 5136.30 One Square 5136.00
Metre
8.2.3 Granite stone slab all colour and texture except black,
Cherry/ Ruby red
8.2.3.1 Area of slab upto 0.50 sqm 1.00 Sqm 4170.70 One Square 4171.00
Metre
8.2.3.2 Area of slab over 0.50 sqm 1.00 Sqm 3848.70 One Square 3849.00
Metre
8.3 Providing edge moulding to 18 mm thick marble stone
counters, Vanities etc., including machine polishing to
edge to give high gloss finish etc. complete as per
design approved by Engineer-in-Charge.

8.3.1 Marble work 1.00 m 298.60 One Metre 299.00

8.3.2 Granite work 1.00 m 510.95 One Metre 511.00
8.4 Extra for fixing marble /granite stone, over and above 1.00 m 568.55 One Metre 569.00
corresponding basic item, in facia and drops of width
upto 150 mm with epoxy resin based adhesive,
including cleaning etc. complete.

8.5 Extra for providing opening of required size & shape for 1.00 No. 978.70 Each 979.00
wash basin/kitchen sink in kitchen platform, vanity
counter and similar location in marble/ Granite/ stone
work, including necessary holes for pillar taps etc.
including moulding, rubbing and polishing of cut edges
etc. complete

8.6 Mirror polishing on marble work/Granite work/stone 1.00 Sqm 506.70 One Square 507.00
work where ever required to give high gloss finish Metre
complete.
8.7 Providing and fixing cramps of required size & shape in
RCC/ CC / Brick masonry backing with cement mortar
1:2 ( 1 cement :2 coarse sand),including drilling
necessary hole in stones and embedding the cramp in
the hole (fastener to be paid separately).

DSR - 2023 IN MS EXCEL Page 39 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
8.7.1 Gunmetal cramps 1.00 Kg 723.45 One Kilogram 723.00

8.7.2 Stainless steel cramps 1.00 Kg 714.40 One Kilogram 714.00

8.8 Providing and fixing expansion hold fasteners on C.C.

/R.C.C. /Brick masonry surface backing including drilling
necessary holes and the cost of bolt etc complete.

8.8.1 Wedge expansion type

8.8.1.1 Fastener with threaded dia 6 mm 1.00 No. 36.75 Each 37.00
8.8.1.2 Fastener with threaded dia 10 mm 1.00 No. 40.00 Each 40.00
8.8.1.3 Fastener with threaded dia 12 mm 1.00 No. 61.70 Each 62.00
8.9 Stone tile (polished) work for wall lining over 12 mm
thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and cement slurry @ 3.3 kg/sqm including
pointing in white cement complete.

8.9.1 8mm thick

8.9.1.1 Raj nagar plain white marble/ Udaipur green marble/ 1.00 Sqm 3190.30 One Square 3190.00
Zebra black marble Metre
8.9.1.2 Granite of any colour and shade 1.00 Sqm 3617.55 One Square 3618.00
Metre
8.10 Providing and fixing stone slab with table rubbed, edges
rounded and polished, of size 75x50 cm deep and 1.8
cm thick, fixed in urinalpartitions by cutting a chase of
appropriate width with chase cutter and embedding the
stone in the chase with epoxy grout or with cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 6 mm nominal size) as per direction of
Engineer-in-charge and finishedsmooth.

8.10.1 White Agaria Marble Stone 1.00 Sqm 3500.45 One Square 3500.00
Metre
8.10.2 Granite Stone of approved shade 1.00 Sqm 4051.85 One Square 4052.00
Metre
8.11 Providing and fixing machine cut, mirror/ eggshell
polished , Marble stone work for wall lining (veneer
work) including dado, skirting, risers of steps etc., in
required design and pattern wherever required, stones
of different finished surface texture, on 12 mm
(average) thick cement mortar 1:3 (1 cement : 3 coarse
sand) laid and jointed with white cement slurry @ 3.3
kg/sqm including pointing with white cement slurry
admixed with pigment of matching shade, including
rubbing, curing, polishing etc. all complete as per
Architectural drawings, and as directed by the Engineer-
in-Charge.

8.11.1 18 mm thick Italian Marble stone slab,Perlato, Rosso 1.00 Sqm 10414.80 One Square 10415.00
verona, Fire Red or Dark Emperadore etc. Metre
8.14 Stone work (machine cut edges) for wall lining etc.
(veneer work) upto 10 metre height, backing filled with
a grout of average 12 mm thick cement mortar 1:3 (1
cement : 3 coarse sand) including pointing in white
cement mortar 1:2 (1 white cement : 2 stone dust) with
an admixture of pigment matching the stone shade :
(To be secured to the backing and the sides by means of
cramps and pins which shall be paid for separately) :

8.14.1 Red sand stone - exposed face fine dressed with rough
backing.

DSR - 2023 IN MS EXCEL Page 40 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
8.14.1.1 70 mm thick 1.00 Sqm 6282.40 One Square 6282.00
Metre
8.14.1.2 60 mm thick 1.00 Sqm 6035.85 One Square 6036.00
Metre
8.14.1.3 50 mm thick 1.00 Sqm 5789.90 One Square 5790.00
Metre
8.14.1.4 40 mm thick 1.00 Sqm 5542.60 One Square 5543.00
Metre
8.14.1.5 30 mm thick 1.00 Sqm 5295.90 One Square 5296.00
Metre
8.14.2 Red sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.2.1 70 mm thick 1.00 Sqm 8502.25 One Square 8502.00
Metre
8.14.2.2 60 mm thick 1.00 Sqm 8255.75 One Square 8256.00
Metre
8.14.2.3 50 mm thick 1.00 Sqm 8009.75 One Square 8010.00
Metre
8.14.2.4 40 mm thick 1.00 Sqm 7762.50 One Square 7763.00
Metre
8.14.2.5 30 mm thick 1.00 Sqm 7515.80 One Square 7516.00
Metre
8.14.3 Red sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.3.1 70 mm thick 1.00 Sqm 7278.20 One Square 7278.00
Metre
8.14.3.2 60 mm thick 1.00 Sqm 6889.45 One Square 6889.00
Metre
8.14.3.3 50 mm thick 1.00 Sqm 6501.55 One Square 6502.00
Metre
8.14.3.4 40 mm thick 1.00 Sqm 6110.75 One Square 6111.00
Metre
8.14.3.5 30 mm thick 1.00 Sqm 5722.60 One Square 5723.00
Metre
8.14.4 White sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.4.1 70 mm thick 1.00 Sqm 9498.10 One Square 9498.00
Metre
8.14.4.2 60 mm thick 1.00 Sqm 9109.30 One Square 9109.00
Metre
8.14.4.3 50 mm thick 1.00 Sqm 8721.45 One Square 8721.00
Metre
8.14.4.4 40 mm thick 1.00 Sqm 8330.65 One Square 8331.00
Metre
8.14.4.5 30 mm thick 1.00 Sqm 7942.50 One Square 7943.00
Metre
8.14.5 Gang saw cut stone
8.14.5.1 30mm thick White sand stone 1.00 Sqm 3256.65 One Square 3257.00
Metre
8.14.5.2 30mm thick Red sand stone 1.00 Sqm 3119.20 One Square 3119.00
Metre
8.15 Providing and fixing stainless steel cramps of required 1.00 Kg 714.40 One Kilogram 714.00
size and shape for anchoring stone wall lining to the
backing or securing adjacent stones in stone wall lining
in cement mortar 1:2 (1 cement : 2 coarse sand),
including making the necessary chases in stone and
holes in wallswherever required.

DSR - 2023 IN MS EXCEL Page 41 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
8.16 Providing and fixing copper pins 7.5 cm long 6 mm 1.00 No. 43.90 Each 44.00
diameter for securing adjacent stones in stone wall
lining in cement mortar 1:2 (1 cement : 2 coarse sand),
including making the necessary chases.

8.17 Wall lining butch work upto 10m height with Dholpur 1.00 Sqm 3135.00 One Square 3135.00
stone 40 mm thick rough facing on the exposed surface Metre
with stone strips of minimum length 300 mm and
required width, including embedding every tenth layer
and bottom most layer in masonry or concrete after
making necessary chases of size 75x75 mm and by
providing layer of 75 mm thick strips i/c 12 mm thick
bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c
ruled pointing in cement mortar 1:2 (1 white cement : 2
stone dust) with an admixture of pigment to match the
shade of stone complete as per direction of Engineer-
in-charge.

8.18 Stone work (machine cut edges Veneer work) for wall
lining upto 10 m height, backing filled with a grout of 12
mm thick cement mortar 1:3 (1 Cement : 3 coarse sand)
and jointed with Cement mortar 1:2 (1 cement : 2 stone
dust), including rubbing and polishing complete. (To be
secured to the backing and the sides by means of
cramps and pins which shallbe paid for separately).

8.18.1 Kota stone slabs exposed face dressed and rubbed.

8.18.1.1 25 mm thick 1.00 Sqm 2651.35 One Square 2651.00
Metre
8.19 Extra for stone work for wall lining on exterior walls of 1.00 Sqm 165.85 One Square 166.00
height more than 10 m from ground level for every Metre
additional height of 3 m or part there of.
8.20 Providing and fixing dry cladding upto 10 metre heights
with 30mm thick gang saw cut stone with (machine cut
edges) of uniform colour andsize upto 1mx1m, fixed to
structural steel frame work and/ or with the help of
cramps, pins etc. and sealing the joints with approved
weather sealant as per Architectural drawing and
direction of Engineer-in-charge. (The steel frame work,
stainless steel cramps and pins etc. shall be paid for
separately).

8.20.1 Red sand stone - 30mm thick gang saw cut stone 1.00 Sqm 2902.65 One Square 2903.00
Metre
8.20.2 White sand stone - 30mm thick gang saw cut stone 1.00 Sqm 3040.10 One Square 3040.00
Metre
8.22 Providing and fixing adjustable stainless steel cramps of 1.00 No. 437.00 Each 437.00
approved quality, required shape and size, adjustable
with stainless steel nuts, bolts and washer (total weight
not less than 260 gms), for dry stone cladding fixed on
frame work at suitable location, including making
necessary recesses in stone slab, drilling required holes
etc complete as per direction of the Engineer-in-charge.

8.23 Providing 50x50x50 mm 2nd class teak wood plugs 1.00 No. 40.85 Each 41.00
including cutting brick work and fixing in cement mortar
1:3 (1 cement : 3 fine sand) and making good the walls
etc.

DSR - 2023 IN MS EXCEL Page 42 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
8.24 Providing and fixing expandable fasteners of specified
size with necessary plastic sleeves and galvanised M.S.
screws including drilling holes in masonry work /CC/
R.C.C. and making good etc. complete.

8.24.1 25 mm long 1.00 No. 22.35 Each 22.00

8.24.2 32 mm long 1.00 No. 24.05 Each 24.00
8.24.3 40 mm long 1.00 No. 28.30 Each 28.00
8.24.4 50 mm long 1.00 No. 29.75 Each 30.00
8.25 Providing and fixing 2nd class teak wood plain lining
tongued and grooved, including wooden plugs
complete with necessary screws and priming coat on
unexposed surface.

8.25.1 40 mm thick 1.00 Sqm 6646.70 One Square 6647.00

Metre
8.25.2 25 mm thick 1.00 Sqm 4437.80 One Square 4438.00
Metre
8.25.3 20 mm thick 1.00 Sqm 3601.30 One Square 3601.00
Metre
8.25.4 12 mm thick 1.00 Sqm 2423.25 One Square 2423.00
Metre
8.26 Providing and fixing in wall lining flat pressed three
layer (medium density) particle board or graded wood
Pre-laminated one side decorative lamination and other
side balancing lamination Grade I, Type II, IS : 12823
marked, including priming coat on unexposed
arrangement andscrews etc. complete :

8.26.1 12 mm thick 1.00 Sqm 1430.20 One Square 1430.00

Metre
8.26.2 18 mm thick 1.00 Sqm 1492.80 One Square 1493.00
Metre
8.26.3 25 mm thick 1.00 Sqm 1979.50 One Square 1980.00
Metre
8.27 Providing and fixing specified wood frame work
consisting of battens 50x25mm fixed with rawl plug and
drilling necessary holes for rawl plug etc. including
priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 1.00 Cum 187277.65 One Cubic 187278.00
Metre
8.28 Providing and fixing plywood 4 mm thick, one side
decorative veneer conforming to IS: 1328 (type-1), for
plain lining / cladding with necessary screws, including
priming coat on unexposed surface with :

8.28.1 Decorative veneer facings of approved manufacture 1.00 Sqm 1946.25 One Square 1946.00
Metre
8.29 Providing and fixing 4mm thick coir veneer board, ISI 1.00 Sqm 1825.05 One Square 1825.00
marked IS : 14842, plain lining with necessary screws, Metre
priming coat on unexposed surface etc., complete.
8.30 Providing and fixing skirting with Pre-laminated (one
side decorative and other side balancing lamination) flat
pressed 3 layer or graded particle board (medium
density) Grade I, Type II, IS :12823 marked, with
necessary fixing arrangements and screws, including
drilling necessary holes for rawl plugs etc. and priming
coat on unexposed surface complete :

8.30.1 18 mm thick 1.00 Sqm 1976.45 One Square 1976.00

Metre
8.30.2 25 mm thick 1.00 Sqm 2463.10 One Square 2463.00
Metre

DSR - 2023 IN MS EXCEL Page 43 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
8.31 Providing and fixing Ist quality ceramic glazed wall tiles 1.00 Sqm 1267.95 One Square 1268.00
conforming to IS: 15622 (thickness to be specified by Metre
the manufacturer), of approvedmake, in all colours,
shades except burgundy, bottle green, black of any size
as approved by Engineer-in-Charge, in skirting, risers of
steps and dados, over 12 mm thick bed of cement
mortar 1:3 (1 cement : 3 coarse sand) and jointing with
grey cement slurry @ 3.3kg per sqm, including pointing
in white cement mixed with pigment of matching shade
complete.

8.32 Designing, fabricating, testing, installing and fixing in 1.00 Sqm 5015.05 One Square 5015.00
position Curtain Wall with Aluminium Composite Panel Metre
Cladding, with open grooves for linear as well as
curvilinear portions of the building , for all heights and
all levels etc. including:

(a) Structural analysis & design and preparation of shop

drawings for pressure equalisation or rain screen
principle as required, proper drainage of water to make
it watertight including checking of all the structural and
functional design.

(b) Providing, fabricating and supplying and fixing

panels of aluminium composite panel cladding in pan
shape in metalic colour of approved shades made out
of 4mm thick aluminium composite panel material
consisting of 3mm thick FR grade mineral core
sandwiched between two Aluminium sheets (each
0.5mm thick). The aluminium composite panel cladding
sheet shall be coil coated, with Kynar 500 based PVDF /
Lumiflon based fluoropolymer resin coating of
approved colour and shade on face # 1 and polymer
(Service) coating on face # 2 as specified using stainless
steel screws, nuts, bolts, washers, cleats, weather
silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 /

MS with Hot Dip Galvanised with serrations and
serrated washers to arrest the wind load movement,
fasteners, SS 316 Pins and anchor bolts of approved
make in SS 316, Nylon separators to prevent bi-metallic
contacts all complete required to perform as per
specification and drawing. The item includes cost of all
material & labour component, the cost of all mock ups
at site, cost of all samples of the individual components
for testing in an approved laboratory, field tests on the
assembled working curtain wall with aluminium
composite panel cladding, cleaning and protection of
the curtain wall with aluminium composite panel
cladding till the handing over of the building for
occupation. Base frame work for ACP cladding is
payable under the relevant aluminium items.

DSR - 2023 IN MS EXCEL Page 44 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
The Contractor shall provide curtain wall with
aluminium composite panel cladding, having all the
performance characteristics all complete , as per the
Architectural drawings, as per item description, as
specified, as per the approvedshop drawings and as
directed by the Engineer-in-Charge. However, for the
purpose of payment, only the actual area on the
external face of the curtain wall with Aluminum
Composite Panel Cladding (including width of groove)
shall be measured in sqm. up to two decimal places.

Total of the Sub-Head - Cladding Work : 454453.00

Sub-Head : Wood and P.V.C. Work
9.1 Providing wood work in frames of doors, windows,
clerestory windows and other frames, wrought framed
and fixed in position with hold fast lugs or with dash
fasteners of required dia & length (hold fast lugs or
dash fastener shall be paid for separately).

9.1.1 Second class teak wood 1.00 Cum 142949.70 One Cubic 142950.00
Metre
9.1.2 Sal wood 1.00 Cum 116520.30 One Cubic 116520.00
Metre
9.1.3 Kiln seasoned and chemically treated hollock wood. 1.00 Cum 83378.05 One Cubic 83378.00
Metre
9.2 Providing laminated veneer lumber conforming to 1.00 Cum 131981.10 One Cubic 131981.00
IS:14616 and TAD -15: 2001 (Part B) in factory made Metre
frames of doors, windows, clerestory windows and
other frames, wrought framed and fixing in position
with hold fast lugs or with dash fasteners of required
dia & length (hold fast lugs or dash fastener shall be
paid for separately).

9.3 Providing wood work in frames of false ceiling,

partitions etc. sawn and fixed in position with necessary
stainless steel screws etc.
9.3.1 Sal wood 1.00 Cum 104754.35 One Cubic 104754.00
Metre
9.3.2 Kiln seasoned and chemically treated hollock wood 1.00 Cum 71337.85 One Cubic 71338.00
Metre
9.4 Extra for additional labour for circular works, such as in
frames of fan light
9.4.1 Second class teak wood 1.00 Cum 14294.95 One Cubic 14295.00
Metre
9.4.2 Sal wood 1.00 Cum 11652.05 One Cubic 11652.00
Metre
9.4.3 Kiln seasoned and chemically treated hollock wood 1.00 Cum 8338.10 One Cubic 8338.00
Metre
9.5 Providing and fixing panelled or panelled and glazed
shutters for doors, windows and clerestory windows,
fixing with butt hinges of required size with necessary
screws, excluding panelling which will be paid for
separately, all complete as per direction of Engineer-in-
charge. (Note: Butt hinges and necessary screws shall
be paid separately)

9.5.1 Second class teak wood

9.5.1.1 35 mm thick shutters 1.00 Sqm 4111.95 One Square 4112.00
Metre
9.5.1.2 30 mm thick shutters 1.00 Sqm 3747.30 One Square 3747.00
Metre

DSR - 2023 IN MS EXCEL Page 45 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.5.2 Kiln seasoned and chemically treated hollock wood
9.5.2.1 35 mm thick shutters 1.00 Sqm 2869.10 One Square 2869.00
Metre
9.5.2.2 30 mm thick shutters 1.00 Sqm 2676.85 One Square 2677.00
Metre
9.5.3 Kiln seasoned selected planks of sheesham wood
9.5.3.1 35 mm thick shutters 1.00 Sqm 3638.35 One Square 3638.00
Metre
9.5.3.2 30 mm thick shutters 1.00 Sqm 3338.65 One Square 3339.00
Metre
9.6 Providing and fixing 35 mm thick factory made
laminated veneer lumber door shutter conforming to
IS : 14616 and TADS 15:2001 (Part B), fixing with butt
hinges of required size with necessary screws, all
complete as per directions of Engineer- in-charge and
panelling with panels of : (Note:- Butt hinges and
necessary screws shall be paid separately)

9.6.1 12 mm thick plain grade -1, medium density flat 1.00 Sqm 3069.05 One Square 3069.00
pressed three layer particle board FPT - I or graded Metre
wood particle board FPT- I, IS : 3087 marked, bonded
with BWP type synthetic resin adhesive as per IS : 848 :

9.6.2 12 mm thick pre-laminated particle board (decorative 1.00 Sqm 3212.70 One Square 3213.00
lamination on both sides) grade -1, medium density flat Metre
pressed, three layer particle board FPT- I or graded
wood particle board FPT- I, conforming to IS : 3087,
bonded with BWP type synthetic resin adhesive as per
IS : 848 and pre-laminated conforming to IS : 12823,
Grade 1, Type - II marked.

9.6.3 12 mm thick one side Pre-laminated particle board 1.00 Sqm 3450.30 One Square 3450.00
(decorative lamination on one side and other sides Metre
balancing lamination) grade -1, medium density flat
pressed, three layer particle board FPT - I or graded
wood particle board FPT-1 conforming to IS : 3087
bonded with BWP type synthetic resin adhesive as per
IS : 848 and pre-laminated conforming to IS : 12823,
Grade -1, Type II marked.

9.7 Providing and fixing panelling or panelling and glazing in

panelled or panelled and glazed shutters for doors,
windows and clerestory windows (Area of opening for
panel inserts excluding portion inside grooves or
rebates to be measured). Panelling for panelled or
panelled and glazed shutters 25 mm to 40 mm thick.

9.7.1 Second class teak wood 1.00 Sqm 3323.20 One Square 3323.00
Metre
9.7.2 Kiln seasoned and chemically treated hollock wood. 1.00 Sqm 2327.10 One Square 2327.00
Metre
9.7.3 Ply wood 5 ply, 9 mm thick
9.7.3.1 Decorative plywood both side decorative veneer (Type - 1.00 Sqm 2724.25 One Square 2724.00
I) conforming to IS 1328 BWR type Metre
9.7.3.2 Decorative plywood one side decorativeveneer and 1.00 Sqm 2698.40 One Square 2698.00
commercial veneer on other face (Type 1) conforming Metre
to IS 1328 BWR Type
9.7.4 Ply wood 7 ply, 9 mm thick
9.7.4.1 Decorative plywood one side decorativeveneer and 1.00 Sqm 2907.05 One Square 2907.00
commercial veneer on other face (Type 1) conforming Metre
to IS 1328 BWR Type

DSR - 2023 IN MS EXCEL Page 46 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.7.5 Particle Board 12 mm thick
9.7.5.1 Plain particle board flat pressed, 3 layer or graded wood 1.00 Sqm 1693.00 One Square 1693.00
particle board medium density Grade I, IS : 3087 Metre
marked
9.7.5.2 Veneered flat pressed three layer or graded wood 1.00 Sqm 2012.05 One Square 2012.00
particle board with commercial veneering on both sides Metre
conforming to IS:3097, grade I
9.7.5.3 Pre-laminated particle board with decorative lamination 1.00 Sqm 2081.05 One Square 2081.00
on one side and balancing lamination on other side, Metre
Grade I, Type II IS: 12823 marked
9.7.5.4 Pre-laminated particle board with decorativelamination 1.00 Sqm 2053.45 One Square 2053.00
on both sides, Grade I, Type II, IS:12823 marked Metre

9.7.6 Coir Veneer Board (conforming to IS 14842)

9.7.6.1 12 mm thick 1.00 Sqm 2253.45 One Square 2253.00
Metre
9.7.7 Float glass panes
9.7.7.1 4 mm thick glass pane (weight not less than 10 kg/sqm). 1.00 Sqm 2241.80 One Square 2242.00
Metre
9.7.7.2 5.0 mm thick glass panes (weight not less than 12.50 1.00 Sqm 2600.45 One Square 2600.00
kg/sqm). Metre
9.7.8 Fly proof stainless steel grade 304 wire gauge with 0.5 1.00 Sqm 1800.45 One Square 1800.00
mm dia. wire and 1.4 mm wide aperture with matching Metre
wood beading
9.9 Providing and fixing glazed shutters for doors, windows
and clerestory windows using 4 mm thick float glass
panes (weight not less than 10 kg per sqm) fixing with
ISI marked M.S. pressed butt hinges bright finished of
required size with necessary screws.

9.9.1 Second class teak wood

9.9.1.1 35 mm thick 1.00 Sqm 4940.20 One Square 4940.00
Metre
9.9.1.2 30 mm thick 1.00 Sqm 4523.40 One Square 4523.00
Metre
9.9.2 Kiln seasoned and chemically treated hollock wood
9.9.2.1 35 mm thick 1.00 Sqm 3524.85 One Square 3525.00
Metre
9.9.2.2 30 mm thick 1.00 Sqm 3305.20 One Square 3305.00
Metre
9.9.3 Kiln seasoned selected planks of sheesham wood
9.9.3.1 35 mm thick 1.00 Sqm 4401.55 One Square 4402.00
Metre
9.9.3.2 30 mm thick 1.00 Sqm 4059.05 One Square 4059.00
Metre
9.10 Providing and fixing factory made laminated veneer
lumber glazed shutter conforming to IS: 14616 and
TADS 15:2001 (Part B), using 4 mm thick float glass
panes for doors, windows and clerestory windows,
fixing with butt hinges of required size with necessary
screws, all as per directions of Engineer-in-charge
(Note:- Butt hinges and necessary screws shall be paid
separately)

9.10.1 30 mm thick shutters 1.00 Sqm 3066.20 One Square 3066.00

Metre
9.11 Extra for providing heavy sheet float glass panes instead
of ordinary float glass in glazed doors, windows and
clerestory window shutters. (Area of opening for glass
panes excluding portion inside rebate shall be
measured)

DSR - 2023 IN MS EXCEL Page 47 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.11.1 5.0 mm thick (weight not less than 12.50 kg per sqm) 1.00 Sqm 295.90 One Square 296.00
instead of 4 mm thick (weight not less than 10 kg per Metre
sqm).
9.12 Extra for providing frosted glass panes 4 mm thick 1.00 Sqm 176.40 One Square 176.00
(weight not less than 10 kg per sqm) instead of ordinary Metre
float glass panes 4 mm thick (weight not less than 10 kg
per sqm) in doors, windows and clerestory window
shutters. (Area of opening for glass panes excluding
portion inside rebate shall be measured).

9.13 Deduct for providing pin headed glass panes instead of 1.00 Sqm -73.95 One Square -74.00
ordinary float glass panes 4 mm thick (weight not less Metre
than 10 kg per sqm) in doors, windows and clerestory
windows shutters (Area of opening for glass panes
excluding portion inside rebate shall be measured).

9.14 Extra for providing ISI marked Stainless Steel butt 1.00 Sqm 193.55 One Square 194.00
hinges instead of M.S. pressed butt hinges bright Metre
finished of required size with necessary screws. (Shutter
area to be measured).

9.15 Deduct for not providing hinges in doors, windows or

clerestory window shutters with :
9.15.1 ISI marked Stainless steel butt hinges with stainless
steel screws :
9.15.1.1 For 2nd class teak wood and other class of wood 1.00 Sqm -253.30 One Square -253.00
shutters Metre
9.15.2 ISI marked M.S. pressed butt hinges bright finished of
required size with necessary screws.
9.15.2.1 For 2nd class teak wood and other class of wood 1.00 Sqm -59.80 One Square -60.00
shutters Metre
9.16 Providing and fixing 25 mm thick shutters for cup board
etc.
9.16.1 Panelled or panelled & glazed shutters
9.16.1.1 Second class teak wood including ISI marked anodised 1.00 Sqm 4402.85 One Square 4403.00
aluminium butt hinges with necessary screws Metre

9.16.1.2 Second class teak wood including ISI marked nickel 1.00 Sqm 4542.90 One Square 4543.00
plated bright finished M.S. piano hingeswith necessary Metre
screws
9.16.2 Glazed shutters :
9.16.2.1 Second class teak wood including ISI marked anodized 1.00 Sqm 4193.25 One Square 4193.00
aluminium butt hinges with necessary screws Metre

9.16.2.2 Second class teak wood including ISI marked nickel 1.00 Sqm 4241.15 One Square 4241.00
plated bright finished M.S. piano hingeswith necessary Metre
screws
9.17 Providing and fixing flat pressed three layer particle or
graded plain wood board medium density exterior
grade (Grade I) FPT-I, conforming and marked to frame,
backing or studding with screws etc. complete (Frames,
backing or studding to be paid separately):

9.17.1 12 mm thick 1.00 Sqm 802.95 One Square 803.00

Metre
9.17.2 18 mm thick 1.00 Sqm 1020.95 One Square 1021.00
Metre

DSR - 2023 IN MS EXCEL Page 48 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.18 Providing and fixing Pre-laminated flat pressed 3 layer
(medium density) particle board or graded wood
particle board IS : 3087 marked, with one side
decorative and other side balancing lamination Grade I,
Type II exterior grade IS : 12823 marked, in shelves with
screws and fittings wherever required, edges to be
painted with polyurethane primer (fittings to be paid
separately).

9.18.1 18 mm thick 1.00 Sqm 1245.75 One Square 1246.00

Metre
9.18.2 25 mm thick 1.00 Sqm 1715.20 One Square 1715.00
Metre
9.20 Providing and fixing ISI marked flush door shutters
conforming to IS : 2202 (Part I) decorative type, core of
block board construction with frame of 1st class hard
wood and well matched teak 3 ply veneering with
vertical grains or cross bands and face veneers on both
faces of shutters.

9.20.1 35 mm thick including ISI marked Stainless Steel butt 1.00 Sqm 3473.85 One Square 3474.00
hinges with necessary screws. Metre
9.20.2 30 mm thick including ISI marked Stainless Steel butt 1.00 Sqm 3167.95 One Square 3168.00
hinges with necessary screws Metre
9.20.3 25 mm thick (for cupboard) including ISI marked nickel 1.00 Sqm 2819.25 One Square 2819.00
plated bright finished M.S. Piano hinges IS : 3818 Metre
marked with necessary screws
9.21 Providing and fixing ISI marked flush door shutters
conforming to IS : 2202 (Part I) non-decorative type,
core of block board construction with frame of 1st class
hard wood and well matched commercial 3 ply
veneering with vertical grains or cross bands and face
veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt 1.00 Sqm 2392.65 One Square 2393.00
hinges with necessary screws Metre
9.21.2 30 mm thick including ISI marked Stainless Steel butt 1.00 Sqm 2172.10 One Square 2172.00
hinges with necessary screws Metre
9.21.3 25 mm thick (for cupboard) including ISI marked nickel 1.00 Sqm 2093.70 One Square 2094.00
plated bright finished M.S. piano hinges with necessary Metre
screws
9.22 Extra for Providing and fixing flush doors with
decorative veneering instead of non decorative ISI
marked flush door shutters conforming to IS: 2202 (Part
I)

9.22.1 On one side only. 1.00 Sqm 478.00 One Square 478.00
Metre
9.23 Extra for providing lipping with 2nd class teak wood 1.00 Sqm 462.35 One Square 462.00
battens 25 mm minimum depth on all edges of flush Metre
door shutters (over all area of door shutter to be
measured).

9.24 Extra for providing vision panel not exceeding 0.1 sqm
in all type of flush doors (cost of glass excluded) (overall
area of door shutter to be measured):
9.24.1 Rectangular or square 1.00 Sqm 199.15 One Square 199.00
Metre
9.24.2 Circular 1.00 Sqm 206.30 One Square 206.00
Metre
9.25 Extra if louvers (not exceeding 0.2 sqm) are provided in
flush door shutters (overall area of door shutters to be
measured).

DSR - 2023 IN MS EXCEL Page 49 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.25.1 Decorative type door 1.00 Sqm 405.45 One Square 405.00
Metre
9.26 Extra for cutting rebate in flush door shutters (Total 1.00 Sqm 106.70 One Square 107.00
area of the shutter to be measured). Metre
9.27 Providing and fixing wire gauge shutters using
galvanized M.S. wire gauge of average width of
aperture 1.4 mm in both directions with wire of dia 0.63
mm, for doors, windows and clerestory windows with
hinges and necessary screws :

9.27.1 35 mm thick shutters.

9.27.1.1.1 with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 4852.30 One Square 4852.00
of required size - Second class teak wood Metre
9.27.1.1.2 with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 3599.20 One Square 3599.00
of required size - Kiln seasoned and chemically treated Metre
hollock wood
9.27.1.1.3 with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 4375.00 One Square 4375.00
of required size - Kiln seasoned selected class of Metre
sheesham wood
9.27.1.2.1 With ISI marked stainless steel butt hinges of required 1.00 Sqm 5045.85 One Square 5046.00
size - Second class teak wood Metre
9.27.1.2.2 With ISI marked stainless steel butt hinges of required 1.00 Sqm 3792.75 One Square 3793.00
size - Kiln seasoned and chemically treated hollock Metre
wood
9.27.1.2.3 With ISI marked stainless steel butt hinges of required 1.00 Sqm 4568.50 One Square 4569.00
size - Kiln seasoned selected class of sheesham wood Metre

9.27.2 30 mm thick shutters

9.27.2.11 with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 4326.80 One Square 4327.00
of required size - Second class teak wood Metre
9.27.2.12 with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 3254.25 One Square 3254.00
of required size - Kiln seasoned and chemically treated Metre
hollock wood
9.27.2.13 with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 3918.15 One Square 3918.00
of required size - Kiln seasoned selected class of Metre
sheesham wood
9.27.2.21 With ISI marked stainless steel butt hinges ofrequired 1.00 Sqm 4520.30 One Square 4520.00
size - Second class teak wood Metre
9.27.2.22 With ISI marked stainless steel butt hinges ofrequired 1.00 Sqm 3447.80 One Square 3448.00
size - Kiln seasoned and chemically treated hollock Metre
wood
9.27.2.23 With ISI marked stainless steel butt hinges ofrequired 1.00 Sqm 4111.70 One Square 4112.00
size - Kiln seasoned selected class of sheesham wood Metre

9.31 Providing and fixing wire gauge laminated veneer

lumber shutters conforming to IS : 14616, and as per
TADS 15 :2001 (Part B) using galvanised wire gauge with
average width of aperture 1.4 mm in both directions
with wire of dia 0.63 mm as per IS :1568, for doors,
windows and clerestory windows, fixing with butt
hinges of required size with necessary screws, as per
directions of Engineer-in-charge: (Note:- Butt hinges
and necessary screws shall be paid separately)

9.31.1 35 mm thick shutters 1.00 Sqm 3066.20 One Square 3066.00

Metre
9.31.2 30 mm thick shutters 1.00 Sqm 2803.00 One Square 2803.00
Metre

DSR - 2023 IN MS EXCEL Page 50 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.40 Providing and fixing wooden moulded beading to door
and window frames with iron screws, plugs and priming
coat on unexposed surface etc. complete :
9.40.1 2nd class teak wood
9.40.1.1 50x12 mm 1.00 m 221.10 One Metre 221.00
9.40.1.2 50 x 20 mm 1.00 m 271.75 One Metre 272.00
9.40.2 Kiln seasoned and chemically treated hollock wood.
9.40.2.1 50x12 mm 1.00 m 185.95 One Metre 186.00
9.40.2.2 50x20 mm 1.00 m 213.20 One Metre 213.00
9.41 Providing and fixing plain jaffri of 35x10 mm laths
placed 35 mm apart (frames to be paid separately),
including fixing 50x12 mm beading complete with
9.41.1 Second class teak wood. 1.00 Sqm 2945.10 One Square 2945.00
Metre
9.42 Providing and fixing 18 mm thick, 150 mm wide pelmet 1.00 m 600.55 One Metre 601.00
of flat pressed three layer or graded plain wood particle
board medium density grade I, ISI marked and
conforming to IS : 3087 marked, including top cover of 6
mm commercial ply wood conforming to IS: 303 BWR
grade, nickel plated M.S. pipe 20 mm dia ( heavy type)
curtain rod with nickel plated brackets, including fixing
with 25x3 mm M.S. flat 10 cm long fixed to pelmet with
hollock wood cleats of size 100 mm x 40 mm x 40 mm
on both inner side of pelmet and rawl plugs 75 mm long
etc. all complete.

9.43 Providing and fixing 18 mm thick, 150 mm wide pelmet 1.00 m 725.85 One Metre 726.00
of coir veneer board ISI marked IS : 14842, including top
cover of 6 mm coir veneer board, nickle plated M.S.
Pipe 20 mm dia. (heavy type) curtain rod with nickel
plated brackets, including fixing with 25x3 mm M.S. Flat
10 cm long fixed to pelmet with hollock wood cleats of
size 100 mm x 40 mm x 40 mm on both inner side of
pelmet and rawl plugs 75 mm long etc. all complete.

9.44 Extra for using veneered particle board conforming to IS

3097 Grade I, in item of pelmet 18 mm thick 150 mm
wide.
9.44.1 Non decorative veneer on both sides. 1.00 m 38.70 One Metre 39.00
9.44.2 Particle board with decorative veneering on both sides 1.00 m 125.20 One Metre 125.00

9.45 Providing and fixing teak wood lipping of size 25x3 mm 1.00 m 73.70 One Metre 74.00
in pelmet.
9.46 Providing and fixing chromium plated brass curtain rod
having wall thickness of 1.25 mm with two chromium
plated brass brackets fixed withC.P. brass screws and
PVC sleeves etc., wherever necessary complete :

9.46.1 12 mm dia 1.00 m 285.10 One Metre 285.00

9.46.2 20 mm dia 1.00 m 393.25 One Metre 393.00
9.46.3 25 mm dia 1.00 m 525.55 One Metre 526.00
9.47 Providing and fixing nickel plated M.S. pipe curtain rods
with nickel plated brackets :
9.47.1 20 mm dia (heavy type) 1.00 m 175.00 One Metre 175.00
9.47.2 25 mm dia (heavy type) 1.00 m 186.40 One Metre 186.00
9.48 Providing and fixing M.S. grills of required pattern in
frames of windows etc. with M.S. flats, square or round
bars etc. including priming coat with approved steel
primer all complete.

DSR - 2023 IN MS EXCEL Page 51 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.48.1 Fixed to steel windows by welding 1.00 Kg 219.10 One Kilogram 219.00

9.48.2 Fixed to openings /wooden frames with rawl plugs 1.00 Kg 238.35 One Kilogram 238.00
screws etc.
9.49 Providing and fixing expanded metal 20x60 mm strands 1.00 Sqm 1421.95 One Square 1422.00
3.25 mm wide and 1.6 mm thick for windows etc. Metre
including 62 x19 mm beading of second class teak wood
and priming coat with approved steel primer all
complete.

9.50 Providing and fixing hard drawn steel wire fabric 75x25 1.00 Sqm 1641.15 One Square 1641.00
mm mesh of weight not less than 7.75 Kg per sqm to Metre
window frames etc. including 62x19 mm beading of
second class teak wood and priming coat with approved
steel primer all complete.

9.51 Providing and fixing fly proof galvanized M.S. wire

gauge to windows and clerestory windows using wire
gauge with average width of aperture 1.4 mm in both
directions with wire of dia 0.63 mm all complete.

9.51.1 With second class teak wood beading 62X19 mm 1.00 Sqm 1308.35 One Square 1308.00
Metre
9.51.2 With 12 mm mild steel U beading 1.00 Sqm 939.20 One Square 939.00
Metre
9.52 Deduct for fixing 75x25 mm hard drawn steel wire 1.00 Sqm -155.10 One Square -155.00
fabric of weight not less than 7.75 Kg per sqm in Metre
panelled and glazed door and window shutter instead
of glass sheet 4 mm thick (weight not less than 10 kg
per sqm)

9.53 Providing 40x5 mm flat iron hold fast 400 mm long 1.00 No. 228.85 Each 229.00
including fixing to frame with 10 mm diameter bolts,
nuts and wooden plugs and embedding in cement
concrete block 300x100x150 mm 1:3:6 mix (1 cement :
3 coarse sand : 6 graded stone aggregate 20 mm
nominal size)

9.54 Providing beams including hoisting, fixing in position

and applying wood preservative for the unexposed
surfaces, etc. complete with :
9.54.1 Sal wood 1.00 Cum 103140.10 One Cubic 103140.00
Metre
9.54.2 Hollock wood 1.00 Cum 69178.05 One Cubic 69178.00
Metre
9.55 Providing and fixing ISI marked IS:1341 M.S. pressed
butt hinges bright finished with necessary screws etc.
complete :
9.55.1 125x65x2.12 mm 1.00 No. 53.00 Each 53.00
9.55.2 100x58x1.90 mm 1.00 No. 45.00 Each 45.00
9.55.3 75x47x1.70 mm 1.00 No. 39.30 Each 39.00
9.55.4 50x37x1.50 mm 1.00 No. 18.85 Each 19.00
9.56 Providing and fixing ISI marked, IS : 1341, M.S. heavy
weight bright finished butt hinges with necessary
screws etc. complete :
9.56.1 125x90x4.00 mm 1.00 No. 71.25 Each 71.00
9.56.2 100x75x3.50 mm 1.00 No. 62.05 Each 62.00
9.56.3 75x60x3.10 mm 1.00 No. 48.15 Each 48.00
9.56.4 50x40x2.50 mm 1.00 No. 27.50 Each 28.00
9.57 Providing and fixing ISI marked IS:1341 oxidised M.S.
pressed butt hinges with necessary screws etc.
complete. (Copper oxidised as per IS 1378)
9.57.1 125x65x2.12 mm 1.00 No. 55.75 Each 56.00

DSR - 2023 IN MS EXCEL Page 52 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.57.2 100x58x1.90 mm 1.00 No. 48.20 Each 48.00
9.57.3 75x47x1.70 mm 1.00 No. 40.50 Each 41.00
9.57.4 50x37x1.50 mm 1.00 No. 20.00 Each 20.00
9.58 Providing and fixing ISI marked IS: 1341 oxidised M.S.
Pressed Parliamentary hinges with necessary screws
etc. complete (Copper oxidised as per IS 1378)
9.58.1 150x125x27x2.80 mm 1.00 No. 91.70 Each 92.00
9.58.2 125x125x27x2.80 mm 1.00 No. 86.00 Each 86.00
9.58.3 100x125x27x2.80 mm 1.00 No. 75.35 Each 75.00
9.58.4 75x100x20x2.24 mm 1.00 No. 66.65 Each 67.00
9.59 Providing and fixing ISI marked oxidised M.S. single
acting spring hinges with necessary screws etc.
complete (Copper oxidised as per IS 1378)
9.59.1 150 mm 1.00 No. 291.35 Each 291.00
9.59.2 125 mm 1.00 No. 262.90 Each 263.00
9.59.3 100 mm 1.00 No. 232.70 Each 233.00
9.60 Providing and fixing ISI marked IS : 453 oxidised M.S.
double acting spring hinges with necessary screws etc.
complete (Copper oxidised as per IS 1378)
9.60.1 150 mm 1.00 No. 326.90 Each 327.00
9.60.2 125 mm 1.00 No. 291.35 Each 291.00
9.60.3 100 mm 1.00 No. 261.15 Each 261.00
9.61 Providing M.S. Piano hinges ISI marked IS : 3818
finished with nickel chromium plating grade 1 as per IS:
1068 and fixing with necessaryscrews etc., complete.

9.61.1 Overall width 35 mm 1.00 m 336.45 One Metre 336.00

9.61.2 Overall width 50 mm 1.00 m 337.90 One Metre 338.00
9.61.3 Overall width 65 mm 1.00 m 357.80 One Metre 358.00
9.62 Providing and fixing ISI marked oxidised M.S. sliding
door bolts with nuts and screws etc. complete (Copper
oxidised as per IS 1378)
9.62.1 300x16 mm 1.00 No. 216.55 Each 217.00
9.62.2 250x16 mm 1.00 No. 193.70 Each 194.00
9.63 Providing and fixing ISI marked oxidised M.S. tower bolt
black finish, (Barrel type) with necessary screws etc.
complete (Copper oxidised as per IS 1378)
9.63.1 250x10 mm 1.00 No. 83.90 Each 84.00
9.63.2 200x10 mm 1.00 No. 69.40 Each 69.00
9.63.3 150x10 mm 1.00 No. 59.45 Each 59.00
9.63.4 100x10 mm 1.00 No. 44.30 Each 44.00
9.64 Providing and fixing ISI marked 85x42 mm oxidised M.S. 1.00 No. 122.15 Each 122.00
pull bolt lock conforming to IS : 7534 with necessary
screws bolts, nut and washers etc. complete (Copper
oxidised as per IS 1378).

9.65 Providing and fixing ISI marked oxidised M.S. door

latches conforming to IS:5930 with screws etc.
complete (Copper oxidised as per IS 1378)
9.65.1 300x20x6 mm 1.00 No. 98.35 Each 98.00
9.65.2 250x20x6 mm 1.00 No. 79.85 Each 80.00
9.66 Providing and fixing ISI marked oxidised M.S. handles
conforming to IS:4992 with necessary screws etc.
complete (Copper oxidised as per IS 1378)
9.66.1 125 mm 1.00 No. 39.95 Each 40.00
9.66.2 100 mm 1.00 No. 32.55 Each 33.00
9.66.3 75 mm 1.00 No. 29.70 Each 30.00

DSR - 2023 IN MS EXCEL Page 53 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.67 Providing and fixing oxidised M.S. hasp and staple
(safety type) conforming to IS : 363 with necessary
screws etc. complete (Copper oxidised as per IS 1378)

9.67.1 150 mm 1.00 No. 33.10 Each 33.00

9.67.2 115 mm 1.00 No. 29.70 Each 30.00
9.67.3 90 mm 1.00 No. 25.30 Each 25.00
9.68 Providing and fixing oxidised M.S. casement stays
(straight peg type) with necessary screws etc. complete
(Copper oxidised as per IS 1378)
9.68.1 300 mm weighing not less than 330 grams 1.00 No. 67.40 Each 67.00
9.68.2 250 mm weighing not less than 280 grams 1.00 No. 61.05 Each 61.00
9.68.3 200 mm weighing not less than 240 grams 1.00 No. 53.95 Each 54.00
9.69 Providing and fixing oxidised M.S. Safety chain with 1.00 No. 100.60 Each 101.00
necessary fixtures for doors, (weighting not less than
450 gms) and Copper oxidised as per IS 1378
9.70 Providing and fixing IS : 12817 marked stainless steel
butt hinges with stainless steel screws etc. complete :
9.70.1 125x64x1.90 mm 1.00 No. 118.20 Each 118.00
9.70.2 100X58X1.90 mm 1.00 No. 107.10 Each 107.00
9.70.3 75x47x1.80 mm 1.00 No. 80.05 Each 80.00
9.70.4 50x37x1.50 mm 1.00 No. 43.75 Each 44.00
9.71 Providing and fixing IS : 12817 marked stainless steel
butt hinges (heavy weight) with stainless steel screws
etc. complete :
9.71.1 125x64x2.50 mm 1.00 No. 129.85 Each 130.00
9.71.2 100x60x2.50 mm 1.00 No. 106.35 Each 106.00
9.71.3 75x50x2.50 mm 1.00 No. 89.30 Each 89.00
9.72 Providing and fixing bright finished brass butt hinges
with necessary screws etc. complete :
9.72.1 125x85x5.5 mm (heavy type) 1.00 No. 268.65 Each 269.00
9.72.2 125x70x4 mm (ordinary type) 1.00 No. 185.15 Each 185.00
9.72.3 100x85x5.5 mm (heavy type) 1.00 No. 206.40 Each 206.00
9.72.4 100x70x4 mm (ordinary type) 1.00 No. 148.25 Each 148.00
9.72.5 75x65x4 mm (heavy type) 1.00 No. 173.40 Each 173.00
9.72.6 75x40x2.5 mm (ordinary type) 1.00 No. 101.85 Each 102.00
9.72.7 50x40x2.5 mm (ordinary type) 1.00 No. 40.90 Each 41.00
9.73 Providing and fixing bright finished brass parliamentary
hinges with necessary screws etc. complete :

9.73.1 150x125x27x5 mm 1.00 No. 463.15 Each 463.00

9.73.2 125x125x27x5 mm 1.00 No. 414.60 Each 415.00
9.73.3 100x125x27x5 mm 1.00 No. 381.75 Each 382.00
9.73.4 75x100x20x3.2 mm 1.00 No. 339.20 Each 339.00
9.74 Providing and fixing bright finished brass tower bolts
(barrel type) with necessary screws etc. complete :
9.74.1 250x10 mm 1.00 No. 441.60 Each 442.00
9.74.2 200x10 mm 1.00 No. 358.40 Each 358.00
9.74.3 150x10 mm 1.00 No. 287.25 Each 287.00
9.74.4 100x10 mm 1.00 No. 197.50 Each 198.00
9.75 Providing and fixing bright finished brass door latch
with necessary screws etc. complete :
9.75.1 300x16x5 mm 1.00 No. 322.20 Each 322.00
9.75.2 250x16x5 mm 1.00 No. 308.00 Each 308.00
9.76 Providing and fixing bright finished brass 100 mm 1.00 No. 854.65 Each 855.00
mortice latch and lock with 6 levers and a pair of lever
handles of approved quality with necessary screws etc.
complete.

DSR - 2023 IN MS EXCEL Page 54 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.77 Providing and fixing bright finished brass 100 mm 1.00 No. 726.60 Each 727.00
mortice latch with one dead bolt and a pair of lever
handles of approved quality with necessary screws etc.
complete.

9.78 Providing and fixing bright finished brass night latch of 1.00 No. 1183.30 Each 1183.00
approved quality including necessary screws etc.
complete.
9.79 Providing and fixing special quality bright finished brass
cupboard or ward robe locks with four levers of
approved quality including necessary screws etc.
complete.

9.79.1 40 mm 1.00 No. 311.20 Each 311.00

9.79.2 50 mm 1.00 No. 356.75 Each 357.00
9.79.3 65 mm 1.00 No. 362.40 Each 362.00
9.79.4 75 mm 1.00 No. 386.60 Each 387.00
9.80 Providing and fixing 50 mm bright finished brass cup 1.00 No. 74.25 Each 74.00
board or wardrobe knob of approved quality with
necessary screws.
9.81 Providing and fixing bright finished brass handles with
screws etc. complete:
9.81.1 125 mm 1.00 No. 256.65 Each 257.00
9.81.2 100 mm 1.00 No. 234.70 Each 235.00
9.81.3 75 mm 1.00 No. 184.95 Each 185.00
9.82 Providing and fixing bright finished brass hanging type 1.00 No. 121.65 Each 122.00
floor door stopper with necessary screws, etc.
complete.
9.83 Providing and fixing aluminium die cast body tubular 1.00 No. 1124.85 Each 1125.00
type universal hydraulic door closer (having brand logo
with ISI, IS : 3564, embossed on the body, door weight
upto 35 kg and door width upto 700 mm), with
necessary accessories and screws etc. complete.

9.84 Providing and fixing aluminium extruded section body 1.00 No. 983.15 Each 983.00
tubular type universal hydraulic door closer (having
brand logo with ISi, IS : 3564, embossed on the body,
door weight upto 36 kg to 80 kg and door width from
701 mm to 1000 mm), with double speed adjustment
with necessaryaccessories and screws etc. complete.

9.85 Providing and fixing bright finished brass casement 1.00 No. 89.00 Each 89.00
window fastener with necessary screws etc. complete.

9.86 Providing and fixing bright finished brass casement

stays (straight peg type) with necessary screws etc.
complete :
9.86.1 300 mm weighing not less than 330 gms 1.00 No. 218.15 Each 218.00
9.86.2 250 mm weighing not less than 280 gms 1.00 No. 175.80 Each 176.00
9.86.3 200 mm weighing not less than 240 gms 1.00 No. 167.25 Each 167.00
9.87 Providing and fixing bright finished brass hasp and
staple (safety type) with necessary screws etc.
complete :
9.87.1 150 mm 1.00 No. 139.10 Each 139.00
9.87.2 115 mm 1.00 No. 126.00 Each 126.00
9.87.3 90 mm 1.00 No. 111.05 Each 111.00
9.88 Providing and fixing chromium plated brass 100 mm 1.00 No. 998.35 Each 998.00
mortice latch and lock with 6 levers and a pair of lever
handles of approved quality with necessary screws etc.
complete.

DSR - 2023 IN MS EXCEL Page 55 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.89 Providing and fixing chromium plated brass night latch 1.00 No. 952.80 Each 953.00
of approved quality including necessary screws etc.
complete.
9.90 Providing and fixing special quality chromium plated
brass cupboard locks with six levers of approved quality
including necessary screws etc. complete.
9.90.1 Size 40 mm 1.00 No. 319.75 Each 320.00
9.90.2 Size 50 mm 1.00 No. 333.95 Each 334.00
9.90.3 Size 65 mm 1.00 No. 372.40 Each 372.00
9.90.4 Size 75 mm 1.00 No. 409.35 Each 409.00
9.91 Providing and fixing chromium plated brass 50 mm 1.00 No. 151.05 Each 151.00
cupboard or wardrobe knobs with nuts complete.
9.92 Providing and fixing chromium plated brass handles
with necessary screws etc. complete:
9.92.1 125 mm 1.00 No. 231.05 Each 231.00
9.92.2 100 mm 1.00 No. 206.25 Each 206.00
9.92.3 75 mm 1.00 No. 176.40 Each 176.00
9.93 Providing and fixing chromium plated brass casement 1.00 No. 155.45 Each 155.00
window fastener with necessary screws etc. complete.

9.94 Providing and fixing chromium plated brass casement

stays (straight peg type) with necessary screws etc.
complete :
9.94.1 300 mm weighing not less than 330 gms 1.00 No. 215.20 Each 215.00
9.94.2 250 mm weighing not less than 280 gms 1.00 No. 191.00 Each 191.00
9.94.3 200 mm weighing not less than 240 gms 1.00 No. 166.80 Each 167.00
9.95 Providing and fixing ISI marked aluminium butt hinges
anodised (anodic coating not less than grade AC 10 as
per IS: 1868) transparent or dyed to required colour or
shade with necessary screws etc. complete:

9.95.1 125x75x4 mm 1.00 No. 150.10 Each 150.00

9.95.2 125x63x4 mm 1.00 No. 126.65 Each 127.00
9.95.3 100x75x4 mm 1.00 No. 115.40 Each 115.00
9.95.4 100x63x4 mm 1.00 No. 104.75 Each 105.00
9.95.5 100x63x3.2 mm 1.00 No. 96.90 Each 97.00
9.95.6 75x63x4 mm 1.00 No. 87.90 Each 88.00
9.95.7 75x63x3.2 mm 1.00 No. 81.50 Each 82.00
9.95.8 75x45x3.2 mm
Note:- Aluminium hinges shall not be used in wooden 1.00 No. 76.50 Each 77.00
shutters , Stainless steel hinges shall be preferred

9.96 Providing and fixing aluminium sliding door bolts ISI

marked anodised (anodic coating not less than grade AC
10 as per IS : 1868) transparent or dyed to required
colour or shade with nuts and screws etc. complete :

9.96.1 300x16 mm 1.00 No. 303.25 Each 303.00

9.96.2 250x16 mm 1.00 No. 260.60 Each 261.00
9.97 Providing and fixing aluminium tower bolts ISI marked
anodised (anodic coating not less than grade AC 10 as
per IS : 1868 ) transparent or dyed to required colour or
shade with necessary screws etc. complete :

9.97.1 300x10 mm 1.00 No. 130.10 Each 130.00

9.97.2 250x10 mm 1.00 No. 115.15 Each 115.00
9.97.3 200x10 mm 1.00 No. 99.70 Each 100.00
9.97.4 150x10 mm 1.00 No. 82.55 Each 83.00
9.97.5 100x10 mm 1.00 No. 64.70 Each 65.00

DSR - 2023 IN MS EXCEL Page 56 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.98 Providing and fixing aluminium pull bolt lock, ISI 1.00 No. 100.80 Each 101.00
marked, anodised (anodic coating not less than grade
AC 10 as per IS : 1868) transparent or dyed to required
colour and shade with necessary screws bolts, nut and
washers etc. complete.

9.99 Providing and fixing 50 cm long aluminium kicking plate 1.00 No. 239.40 Each 239.00
of size 100x3.15 mm, anodised (anodic coating not less
than grade AC 10 as per IS :1868) transparent or dyed
to required colour or shade, with necessary screws etc.
complete.

9.100 Providing and fixing aluminium handles ISI marked,

anodised (anodic coating not less than grade AC 10 as
per IS : 1868) transparent or dyed to required colour or
shade with necessary screws etc. complete :

9.100.1 125 mm 1.00 No. 66.25 Each 66.00

9.100.2 100 mm 1.00 No. 59.55 Each 60.00
9.100.3 75 mm 1.00 No. 51.75 Each 52.00
9.101 Providing and fixing aluminium hanging floor door
stopper, ISI marked, anodised (anodic coating not less
than grade AC 10 as per IS : 1868) transparent or dyed
to required colour and shade, with necessary screws
etc. complete.

9.101.1 Single rubber stopper 1.00 No. 39.60 Each 40.00

9.101.2 Twin rubber stopper 1.00 No. 72.35 Each 72.00
9.102 Providing and fixing aluminium casement stays, ISI 1.00 No. 71.50 Each 72.00
marked, anodised (anodic coating not less than grade
AC 10 as per IS : 1868) transparent or dyed to required
colour and shade, with necessary screws etc. complete.

9.103 Providing and fixing bright finished brass 100 mm 1.00 No. 868.95 Each 869.00
mortice latch and lock, ISI marked, with six levers and a
pair of anodised (anodic coating not less than grade AC
10 as per IS : 1868) aluminium lever handles of
approved quality with necessary screws etc. complete.

9.104 Providing and fixing aluminium tee channels (heavy 1.00 m 160.35 One Metre 160.00
duty) with rollers & stop end in pelmets as curtain rod.

DSR - 2023 IN MS EXCEL Page 57 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.105 Providing and fixing partition upto ceiling height
consisting of G.l. frame and required board, including
providing and fixing of frame work made of special
section power pressed/ roll form G.l. sheet with zinc
coating of 120 gms/sqm(both side inclusive), consisting
of floor and ceiling channel 50mm wide having equal
flanges of 32 mm and 0.50 mm thick, fixed to the floor
and ceiling at the spacing of 610 mm centre to centre
with dash fastener of 12.5 mm dia meter 50 mm length
or suitable anchor fastener or metal screws with nylon
plugs and the studs 48 mm wide having one flange of
34 mm and other flange 36 mm and 0.50 mm thick
fixed vertically within flanges of floor and ceiling
channel and placed at a spacing of 610 mm centre to
centre by 6 mm dia bolts and nuts, including fixing of
studs along both ends of partition fixed flush to wall
with suitable anchor fastener or metal screws with
nylon plugs at spacing of 450 mm centre to centre, and
fixing of boards to both side of frame work by 25 mm
long dry wall screws on studs, floor and ceiling channels
at the spacing of 300 mm centre to centre. The boards
are to be fixed to the frame work with joints staggered
to avoid through cracks, M.S. fixing channel of 99 mm
width (0.9 mm thick having two flanges of 9.5 mm each)
to be provided at the horizontal joints of two boards,
fixed to the studs using metal to metal flat head screws,
including jointing and finishing to a flush finish with
recommended jointing compound, jointing tape, angle
beads at corners (25 mm x 25 mm x 0.5 mm), joint
finisher and two coats of primer suitable for board as
per manufacture's specification and direction of
engineer in charge all complete.

9.105.1 75 mm overall thickness partition with 12.5 mm thick 1.00 Sqm 2131.10 One Square 2131.00
double skin fire rated Glass Reinforced Gypsum (GRG) Metre
plaster board conforming to IS: 2095: (part 3) (Board
with BIS certification marks)

9.105.2 75mm overall thickness partition with 12.5 mm thick 1.00 Sqm 1818.15 One Square 1818.00
double skin tapered edged plain Gypsum plaster board Metre
conforming to IS: 2095: (part 1) : 2011 (Board with BIS
certification marks)

9.105.3 66mm overall thickness Partition with 8mm thick 1.00 Sqm 2225.00 One Square 2225.00
double skin Calcium Silicate Board made with Metre
Calcareous & Siliceous materials reinforced with
cellulose fiber manufactured through autoclaving
process with Compressive Strength 225 kg/sq.cm,
Bending Strength 100 kg./ sq.cm

9.105.4 66mm overall thickness partition using 8mm thick, 1.00 Sqm 2062.85 One Square 2063.00
double skin multipurpose cement board, Type-B, Metre
Category-Ill as per IS : 14862:2000 reinforced with
cellulose fibre manufactured through autoclaving
process (High pressure steam cured) with suitable fibre
cement screws

9.105.5 66 mm overall thickness partition using 8 mm thick 1.00 Sqm 2034.40 One Square 2034.00
double skin multipurpose cement bonded wood particle Metre
board manufactured as per IS: 14276 with suitable
cement bonded board screws

9.106 Providing and fixing PTMT handles with necessary

screws etc. complete.
9.106.1 125x34x24 mm weighing not less than 23 gms 1.00 No. 42.95 Each 43.00
9.106.2 150x34x24 mm weighing not less than 26 gms 1.00 No. 41.55 Each 42.00
9.107 Providing and fixing PTMT Butt hinges with necessary
screws etc. complete.

DSR - 2023 IN MS EXCEL Page 58 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.107.1 75 x 60 x 10 mm fitted with 5.5 mm dia M.S. Bright Bar 1.00 No. 75.90 Each 76.00
Rod weighing not less than 34 gms
9.107.2 100 x 75 x 10 mm fitted with 5.5 mm dia MS Bright Bar 1.00 No. 89.10 Each 89.00
Rod weighing not less than 53 gms
9.108 Providing and fixing PTMT Tower Bolts with 12 mm one
piece rod inside and necessary screws etc., complete.

9.108.1 152x42x18 mm weighing not less than 60 gms 1.00 No. 69.75 Each 70.00
9.108.2 202x42x18 mm weighing not less than 78 gms 1.00 No. 106.15 Each 106.00
9.109 Providing and fixing PTMT door catcher of length 72 1.00 No. 40.05 Each 40.00
mm and dia. of 42 mm with suitable washers weighing
not less than 33 gms
9.110 Providing and fixing Bamboo jaffery/ fencing consisting 1.00 Sqm 689.40 One Square 689.00
of superior quality 25 mm dia (Average) half cut Metre
bamboo placed vertically and fixed together with three
numbers horizontal running members of hollock wood
in scantling of section 50X25 mm, fixed with nails and
G.I wire on existing support complete as per direction of
Engineer-in-charge.

9.111 Providing and fixing wooden moulded corner beading of

triangular shape to the junction of panelling etc. with
iron screws, plugs and priming coat on unexposed
surface etc. complete 2nd class teak wood.

9.111.1 50x50mm (base and height). 1.00 m 354.35 One Metre 354.00
9.112 Providing and fixing 2nd class teak wood lipping/ 1.00 m 102.15 One Metre 102.00
moulded beading or taj beading of size 18X5 mm fixed
with wooden adhesive of approved quality and screws/
nails on the edges of the Pre-laminated particle board
as per direction of Engineer-in-charge.

9.113 Providing and fixing bright finished 100 mm mortice 1.00 No. 850.05 Each 850.00
lock with 6 levers without pair of handles of approved
quality for aluminium door, with necessary screws etc
complete as per direction of Engineer-in-charge.

9.114 Providing and fixing magnetic catcher of approved

quality in cupboard / ward robe shutters, including
fixing with necessary screws etc. complete.
9.114.1 Triple strip vertical type 1.00 No. 52.50 Each 53.00
9.114.2 Double strip (horizontal type) 1.00 No. 39.70 Each 40.00
9.115 Providing and fixing powder coated telescopic drawer 1.00 sets 414.20 Each Set 414.00
channels 300 mm long with necessary screws etc.
complete as per directions of Engineer-in-charge.

9.116 Providing and fixing sliding arrangement in racks/ 1.00 No. 20.40 Each 20.00
cupboards/cabinets shutter with stainless steel rollers
to run inside C or E aluminium channel section (The
payment of C or E channel shall be made separately)

DSR - 2023 IN MS EXCEL Page 59 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.117 Providing and fixing factory made uPVC door frame
made of uPVC extruded sections having an overall
dimension as below (tolerance ±1mm), with wall
thickness 2.0 mm (± 0.2 mm), corners of the door frame
to be Jointed with galvanized brackets and stainless
steel screws, joints mitred and Plastic welded. The
hinge side vertical of the frames reinforced by
galvanized M.S. tube of size 19 X 19 mm and 1mm (±
0.1 mm) wall thickness and 3 nos. stainless steel hinges
fixed to the frame complete as per manufacturer’s
specification and direction of Engineer-in-charge

9.117.1 Extruded section profile size 48x40 mm 1.00 m 270.20 One Metre 270.00
9.117.2 Extruded section profile size 42x50 mm 1.00 m 331.35 One Metre 331.00
9.118 Providing and fixing to existing door frames.
9.118.1 24 mm thick factory made PVC door shutters made of 1.00 Sqm 2969.25 One Square 2969.00
styles and rails of a uPVC hollow section of size 59x24 Metre
mm and wall thickness 2 mm (± 0.2 mm) with inbuilt
edging on both sides. The styles and rails mitred and
joint at the corners by means of M.S. galvanised/plastic
brackets of size 75x220 mm having wall thickness 1.0
mm and stainless steel screws. The styles of the shutter
reinforced by inserting galvanised M.S. tube of size
20x20 mm and 1 mm (± 0.1 mm) wall thickness. The
lock rail made up of ‘H’ section, a uPVC hollow section
of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,
fixed to the shutter styles by means of
plastic/galvanised M.S. ‘U’ cleats. The shutter frame
filled with a uPVC multi-chambered single panel of size
not less than 620 mm, having over all thickness of 20
mm and 1 mm (± 0.1 mm) wall thickness. The panels
filled vertically and tie bar at two places by inserting
horizontally 6 mm galvanised M.S. rod and fastened
with nuts and washers, complete as per manufacturer’s
specification and direction of Engineer-in-charge. (For
W.C. and bathroom door shutter).

9.118.2 30 mm thick factory made Polyvinyl Chloride (PVC) door 1.00 Sqm 3253.80 One Square 3254.00
shutter made of styles and rails of a uPVC hollow Metre
section of size 60x30 mm and wall thickness 2 mm (±
0.2 mm), with inbuilt decorative moulding edging on
one side. The styles and rails mitred and joint at the
corners by means of M.S. galvanised/ plastic brackets of
size 75x220 mm having wall thickness 1.0 mm and
stainless steel screws. The styles of the shutter
reinforced by inserting galvanised M.S. tube of size
25x20 mm and 1 mm (± 0.1 mm) wall thickness. The
lock rail made up of ‘H’ section, a uPVC hollow section
of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness
fixed to the shutter styles by means of plastic/
galvanised M.S. ‘U’ cleats. The shutter frame filled with
a uPVC multi-chambered single panel of size not less
than 620 mm, having over all thickness of 20 mm and 1
mm (± 0.1 mm) wall thickness . The panels filled
vertically and tie bar at two places by inserting
horizontally 6 mm galvanised M.S. rod and fastened
with nuts and washers, complete as per manufacturer’s
specification and direction of Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 60 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.118.3 25 mm thick PVC flush door shutters made out of a one 1.00 Sqm 3068.85 One Square 3069.00
piece Multi chamber extruded PVC section of the size of Metre
762 mm X 25 mm or less as per requirement with an
average wall thickness of 1 mm (± 0.3 mm). PVC foam
end cap of size 23x10 mm are provided on both vertical
edges to ensure the overall thickness of 25 mm. M.S.
tube having dimensions 19 mm x 19 mm and 1.0 mm (±
0.1 mm) is inserted along the hinge side of the door.
Core of the door shutter should be filled with High
Density Polyurethane foam. The Top & Bottom edges of
the shutter are covered with an end-cap of the size 25
mm X 11 mm. Door shutter shall be reinforced with
special polymeric reinforcements as per manufacturer’s
specification and direction of Engineer- in-charge to
take up necessary hardware and fixtures. Stickers
indicating the locations of hardware will be pasted at
appropriate places.

9.119 Providing and fixing factory made P.V.C. door frame of 1.00 m 492.70 One Metre 493.00
size 50x47 mm with a wall thickness of 5 mm, made out
of extruded 5mm rigid PVC foam sheet, mitred at
corners and joined with 2 Nos of 150 mm long brackets
of 15x15 mm M.S. square tube, the vertical door frame
profiles to be reinforced with 19x19 mm M.S. square
tube of 19 gauge, EPDM rubber gasket weather seal to
be provided through out the frame. The door frame to
be fixed to the wall using M.S. screws of 65/100 mm
size, complete as per manufacturer’s specification and
direction of Engineer-in-Charge.

9.120 Providing and fixing factory made panel PVC door

shutter consisting of frame made out of M.S. tubes of
19 gauge thickness and size of 19 mm x 19 mm for
styles and 15x15 mm for top & bottom rails. M.S. frame
shall have a coat of steel primers of approved make and
manufacture. M.S. frame covered with 5 mm thick heat
moulded PVC ‘C’ channel of size 30mm thickness, 70
mm width out of which 50 mm shall be flat and 20 mm
shall be tapered in 45 degree angle on both side
forming styles and 5 mm thick, 95 mm wide PVC sheet
out of which 75 mm shall be flat and 20 mm shall be
tapered in 45 degree on the inner side to form top and
bottom rail and 115 mm wide PVC sheet out of which
75 mm shall be flat and 20 mm shall be tapered on both
sides to form lock rail. Top, bottom and lock rails shall
be provided both side of the panel. 10 mm (5 mm x 2 )
thick, 20 mm wide cross PVC sheet be provided as gap
insert for top rail & bottom rail, paneling of 5 mm thick
both side PVC sheet to be fitted in the M.S. frame
welded/ sealed to the styles & rails with 7 mm (5 mm+2
mm) thick x 15 mm wide PVC sheet beading on inner
side, and joined together with solvent cement adhesive.
An additional 5 mm thick PVC strip of 20 mm width is to
be stuck on the interior side of the ‘C’ Channel using
PVC solvent adhesive etc. complete as per direction of
Engineer-in-charge, manufacturer’s specification &
drawing.

DSR - 2023 IN MS EXCEL Page 61 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.120.1 30 mm thick plain PVC door shutters. 1.00 Sqm 3182.95 One Square 3183.00
Metre
9.120.2 30 mm thick pre laminated PVC door shutters 1.00 Sqm 3663.80 One Square 3664.00
Metre
9.121 Providing and fixing Fiber Glass Reinforced plastic (FRP) 1.00 m 570.95 One Metre 571.00
Door Frames of cross-section 90 mm x 45 mm having
single rebate of 32 mm x 15 mm to receive shutter of 30
mm thickness. The laminate shall be moulded with fire
resistant grade unsaturated polyester resin and
chopped mat. Door frame laminate shall be 2 mm thick
and shall be filled with suitable wooden block in all the
three legs. The frame shall be covered with fiber glass
from all sides. M.S. stay shall be provided at the bottom
to steady the frame.

9.122 Providing and fixing to existing door frames.

9.122.1 30 mm thick Glass Fibre Reinforced Plastic (FRP) 1.00 Sqm 3720.75 One Square 3721.00
panelled door shutter of required colour and approved Metre
brand and manufacture, made with fire - retardant
grade unsaturated polyester resin, moulded to 3 mm
thick FRP laminate for forming hollow rails and styles,
with wooden frame and suitable blocks of seasoned
wood inside at required places for fixing of fittings, cast
monolithically with 5 mm thick FRP laminate for panels
conforming to IS: 14856, including fixing to frames.

9.122.2 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush 1.00 Sqm 4488.95 One Square 4489.00
door shutter in different plain and wood finish made Metre
with fire retardant grade unsaturated polyester resin,
moulded to 3 mm thick FRP laminate all around, with
suitable wooden blocks inside at required places for
fixing of fittings and polyurethane foam (PUF)/
Polystyrene foam to be used as filler material
throughout the hollow panel, casted monolithically with
testing parameters of F.R.P. laminate conforming to
table - 3 of IS: 14856, complete as per direction of
Engineer-in-charge.

9.123 Providing and fixing factory made door frame (single 1.00 m 696.00 One Metre 696.00
rebate) made out of solid foam PVC extruded profile of
minimum 60mm width and minimum 30 mm thickness,
having homogenous fine cellular structure and integral
smooth outer skin. The frame's vertical and horizontal
members to be mitered cut and joined together with
PVC solvent adhesive / cement and both corners
strengthened with fully threaded steel screws (of
required size) fixed diagonally. The door frame is to be
fixed to door jambs using 6 Nos. SS 304 grade minimum
8 mm dia CSK Phillips stainless steel self tapping
screws/fasteners with PA6 grade polyamide sleeves
both of required size, and gap if any between the door
frame and the jamb must be filled with clear silicon,
complete as per direction of the Engineer-in- Charge.

DSR - 2023 IN MS EXCEL Page 62 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.123A Providing PVC moulding / architrave for door frame 1.00 m 135.80 One Metre 136.00
made up of extruded solid foam PVC profile having
homogenous fine cellular structure with smooth outer
integral skin, minimum 30 mm width and minimum
12mm thick suitable for fixing to frame. The moulding
shall be snap fitted in the groove provided in the frame
& fixed with PVC solvent adhesive / cement and self
tapping screws (of required size) complete as per
direction of Engineer-in-Charge.

9.124 Providing and fixing factory made PVC Door shutter

made of solid foam PVC profiles of thickness 5 mm and
15 mm at edges integrally extruded for vertical style
and horizontal (top / bottom / lock) rails of minimum
cross section of 70mm x 28mm, of shape and design as
per manufacturer's specifications having homogenous
fine cellular structure and smooth integral outer skin,
inserted with G.l. 'C' section/ rectangular tube profile of
minimum 0.30 mm thickness with 120 gsm coating as
stiffeners as per manufacturer's specifications Mitered
cut joints for styles and rails provided with telescopic
polymeric L' corners are joined together using solvent
adhesive and strengthened with fully threaded stainless
steel screws (of required size) through reinforcement
stiffener with paneling of specified solid foam PVC
board / high pressure laminate of required thickness
and of approved design and shade (matching the styles
and rails), secured within styles and rails with specially
designed solid foam PVC moulded headings of required
size using PVC solvent adhesive / cement. The finished
door shutter including SS hardware, 1 no. SS sliding
door bolt 200 x 10mm, 1 no. SS tower bolt 200 x 10mm
and 2 nos. SS handles 125 mm, shall be fixed to frame
with 3 Nos. stainless steel hinges of minimum size
100x58x1.9mm and stainless steel screws of required
size complete as per direction of the Engineer-in-
Charge.(Cost of above hardware is inclusive in rates)

9.124.1 5 mm thick solid foam PVC panel of required size with 1.00 Sqm 3754.20 One Square 3754.00
moulded/extruded beading of appropriate design shape Metre
and size as per manufacturer's specifications (to secure
the panel insert tight in place within the style and rails
of the shutter)matching the color &shade of shutter
frame - Non decorative type.

9.124.2 5 mm thick solid foam PVC panel of required size with 1.00 Sqm 4138.35 One Square 4138.00
moulded / extruded beading of appropriate design Metre
shape and size as per manufacturer's specifications (to
secure the panel insert tight in place within the style
and rails of the shutter)matching the design, color &
shade of shutter frame. - Decorative type.

DSR - 2023 IN MS EXCEL Page 63 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.124.3 3 mm thick high pressure laminate (decorative type) 1.00 m 4678.95 One Metre 4679.00
with moulded /extruded beading of appropriate design
shape and size as per manufacturer's specifications (to
secure the panel insert tight in place within the style
and rails of the shutter) matching the design, color &
shade of shutter frame. Non Ddcorative type

9.126 Providing and fixing 12 mm thick panelling or panelling

and glazing in panelled or panelled and glazed shutters
for doors, windows and clerestory windows (area of
opening for panel inserts excluding portion inside
grooves or rebates to be measured). Panelling for
panelled or panelled and glazed shutters 25 mm to 40
mm thick.

9.126.1 Marine plywood conforming to IS: 710 1.00 Sqm 2486.25 One Square 2486.00
Metre
9.126.2 Fire retardant plywood conforming to IS: 5509. 1.00 Sqm 2777.70 One Square 2778.00
Metre
9.127 Providing & Fixing decorative high pressure laminated
sheet of plain / wood grain in gloss / matt / suede finish
with high density protective surface layer and reverse
side of adhesive bonding quality conforming to IS : 2046
Type S, including cost of adhesive of approved quality.

9.127.1 1.5 mm thick. 1.00 Sqm 1045.95 One Square 1046.00

Metre
9.127.2 1.0 mm thick. 1.00 Sqm 897.30 One Square 897.00
Metre
9.128 Providing and fixing factory made Fiberglass Reinforced 1.00 Sqm 5207.45 One Square 5207.00
Plastic (F.R.P.) Chhajja 4mm thick of required colour size Metre
and design made of Resin Transfer moulding
(RTM)Machine technology, resulting in void free
compact laminate in single piece, having smooth
gradual slope curvature for easy drainage of water and
duly reinforced by 2 nos vertically and 1 no horizontally
mm thick MS flat with 12mm inbuilt hole for grouting
on the existing wallalongwith 50mm flangesduly
inserted and sealed in the wall completein one single
piece casted monolithically, including all necessary
fittings. The FRP chhajja should be manufactured using
unsaturated polyester resin as per IS: 6746, duly
reinforced with fiber glass chopped strand mash (CSM)
as per IS:11551 complete with protective Gel coat U/V
coating on top for complete resistance from the
extreme of tempetrature, weather & sunlight (only plan
area of chhajjas shall be measured for making payment)

9.129 Providing and fixing cup board shutters 25mm thick, 1.00 Sqm 2307.35 One Square 2307.00
with Pre-laminated flat pressed three layer particle Metre
board or graded wood particle board IS: 12823 marked
exterior grade (Grade l Type ll) having one side
decorative lamination and other side balancing
lamination including IInd class teak wood lipping of
25mm wide x12 mm thick with necessary screws and
bright finished stainless steel piano hinges complete as
per direction of the Engineer-in-Charge

DSR - 2023 IN MS EXCEL Page 64 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.130 Providing and fixing cup board shutters with 25mm
thick veneered particle board IS : 3097 marked exterior
grade (Grade I) of approved make including IInd class
teak wood lipping of 25mm wide x 12 mm thick with
necessary screws and bright finished stainless steel
piano hinges complete as per direction of Engineer-in-
Charge.

9.130.1 With decorative veneering on one side and commercial 1.00 Sqm 1927.50 One Square 1928.00
veneering on other side. Metre
9.130.2 With non decorative veneering on both sides. 1.00 Sqm 1809.40 One Square 1809.00
Metre
9.131 Providing and fixing factory made shutters of Pre-
laminated particle board flat pressed three layer or
graded wood particle board with one side decorative
finish and other side balancing lamination conforming
to IS: 12823 Grade l Type ll, of approved design, and
edges sealed with water resistant paint and lipped with
aluminium 'U' type edge beading all-round the shutter,
including fixing with angle cleat, grip strip, cadmium
plated steel screws including fixing of aluminium hinges
100x63x4 mm etc. complete as per architectural
drawing and direction of Engineer-in-Charge (Cost of 'U'
beading and hinges will be paid for separately).

9.131.1 25 mm thick. 1.00 Sqm 1801.60 One Square 1802.00

Metre
9.132 Providing and fixing aluminum U beading of required 1.00 Kg 596.15 One Kilogram 596.00
size to Pre-laminated /flush door shutter including fixing
etc. complete as per direction of Engineer-in-charge.

9.133 Providing and fixing, in position concealed G.l. section

for wall paneling using board of required thickness fixed
on the 'W profile (0.55 mm thick) having a knurled web
of 51.55 and two flanges of 26mm each with lips of
10.55mm placed @610mm c/c mm with thickness of
0.55 mm and web in perimeter channel having one
flange of 20mm and another flange of 30mm with
thickness of 0.55 mm and web of length 27 mm.
Perimeter channel is fixed on the floor and the ceiling
with the nylon sleeves @610 mm C/C with fully
threaded self-tapping dry wall screws. Board is fixed to
the W profile with 25 mm countersunk ribbed head
screws @ 200 mm C/C., all complete as per the drawing
& directions of engineer-in-charge, the joints of the
boards are finished with specially formulated jointing
compound and 48mm wide jointing tape to provide
seamless finish.

9.133.1 Tapered edge calcium silicate board made with

calcareous & siliceous materials reinforced with
cellulose fiber manufactured through autoclaving
process to give stable crystalline structure with
compressive strength 225 kg/sq.cm, Bending strength
100kg/sq.cm.

9.133.1.1 10mm thick. 1.00 Sqm 1790.95 One Square 1791.00

Metre
9.133.2 Multipurpose cement board reinforced with suitable
fibre cement screw

DSR - 2023 IN MS EXCEL Page 65 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.133.2.1 8 mm thick cement fibre board, Type- B, Category- III as 1.00 Sqm 1443.45 One Square 1443.00
per IS 14862:2000 Metre
9.133.2.2 8 mm thick cement bonded wood particle board as per 1.00 Sqm 1427.80 One Square 1428.00
IS:14276. Metre
9.133.3 Plain Gypsum plaster board conforming to IS:
2095( Part - I) : 2011 (Board with BIS certification
marks)
9.133.3.1 12.5 mm thick. 1.00 Sqm 1308.85 One Square 1309.00
Metre
9.134 Providing and fixing wire gauge shutters using stainless
steel grade 304 wire gauge with wire of dia 0.5 mm and
average width of aperture 1.4 mm in both directions for
doors, windows and clerestory windows with necessary
screws:

9.134.1 35 mm thick shutters

9.134.1.1.1with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 5024.15 One Square 5024.00
of required size - Second class teak wood Metre
9.134.1.1.2with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 3771.00 One Square 3771.00
of required size-Kiln seasoned and chemically treated Metre
hollock wood.
9.134.1.1.3with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 4546.80 One Square 4547.00
of required size - Kiln seasoned selected class of Metre
sheesham wood.
9.134.1.2.1With ISI marked stainless steel butt hinges of required 1.00 Sqm 5217.65 One Square 5218.00
size. - Second class teak wood. Metre
9.134.1.2.2With ISI marked stainless steel butt hinges of required 1.00 Sqm 3964.55 One Square 3965.00
size. - Kiln seasoned and chemically treated hollock Metre
wood.
9.134.1.2.3With ISI marked stainless steel butt hinges of required 1.00 Sqm 4740.30 One Square 4740.00
size. - Kiln seasoned selected class of sheesham wood. Metre

9.134.2 30 mm thick shutters.

9.134.2.1.1with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 4498.60 One Square 4499.00
of required size - Second class teak wood. Metre
9.134.2.1.2with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 3426.05 One Square 3426.00
of required size. - Kiln seasoned and chemically treated Metre
hollock wood.
9.134.2.1.3with ISI marked M.S. pressed butt hinges bright finished 1.00 Sqm 4090.00 One Square 4090.00
of required size. - Kiln seasoned selected class of Metre
sheesham wood.
9.134.2.2.1With ISI marked stainless steel butt hinges of required 1.00 Sqm 4692.10 One Square 4692.00
size. - Second class teak wood Metre
9.134.2.2.2With ISI marked stainless steel butt hinges of required 1.00 Sqm 3619.60 One Square 3620.00
size - Kiln seasoned and chemically treated hollock Metre
wood.
9.134.2.2.3With ISI marked stainless steel butt hinges of required 1.00 Sqm 4283.50 One Square 4284.00
size - Kiln seasoned selected class of sheesham wood. Metre

9.135 Providing and fixing fly proof stainless steel grade 304
wire gauge, to windows and clerestory windows using
wire gauge with average width of aperture 1.4mm in
both directions with wire of dia. 0.50 mm all complete.

9.135.1 With 2nd class teak wood beading 62X19 mm. 1.00 Sqm 1597.15 One Square 1597.00
Metre
9.135.2 With 12 mm mild steel U beading. 1.00 Sqm 1228.00 One Square 1228.00
Metre

DSR - 2023 IN MS EXCEL Page 66 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.136 Providing and fixing fire resistant door frame of section 1.00 m 1709.25 One Running 1709.00
143 x 57 mm having built in rebate made out of 16 SWG Metre
G.I. sheet (zinc coating not less than 120gm/sqm) duly
filled with vermiculite based concrete mix, suitable for
mounting 60 minutes fire rated door shutters. The
frame is fitted with intumuscent fire seal strip of size
10x4 mm (minimum) alround the frame and fixing with
dash fastener of approved size and make, including
applying a coat of approved brand fire resistant primer
etc. complete as per direction of Engineer-in-
charge(Dash fastener to be paid for separately).

9.137 Providing and fixing 50 mm thick glazed fire resistant 1.00 Sqm 7533.20 One Square 7533.00
door shutters of 60 minutes fire rating conforming to Metre
IS:3614 (Part-II) tested and certified as per laboratory
approved by Engineer-in-charge with suitable mounting
on doorframe, consisting of vertical styles, lock rail, top
rail 100mm wide, bottom rail 200mm wide, made out of
16 SWG G.I. sheet (zinc coating not less than 120
gm/sqm) duly filled FR insulation material and fixing
with necessary stainless steel ball bearing hinges of
approved make, including applying a coat of approved
fire resistant primer etc. all complete as per direction of
Engineer-in- charge (pannelling to be paid for
separately).

9.138 Providing and fixing glazing in fire resistant door 1.00 Sqm 40405.55 One Square 40406.00
shutters, fixed panels & partitions etc., with G.I. beading Metre
made out 1.6 mm thick G.I. sheet (zinc coating not less
than 120 gm/sqm) of size 20 x 33 mm screwed with M4
x 38 mm SS screws at distance of 75 mm from the
edges and 150 mm c/c, including applying a coat of
approved fire resistant primer/ powder coating of not
less than 30 micron on G.I. beading & special ceramic
tape of 5 x 20 mm size etc. complete in all respect as
per NBC 2016, IS 16231 (Part 3) :2016 and as per
direction of Engineer-in-charge with glass of required
thickness having 60 minutes of fire resistance both
integrity & radiation control (EW60) and minimum 20
min of insulation (EI20). The manufacturer has to give
test report / certification of fire glass and the glass
should have the stamp showing the value of E, EW & EI.
The glass shall be tested in approved NABL accredited
lab or any other accreditation body which operates in
accordance with ISO/ IEC 17011 and accredits labs as
per ISO/ IEC 17025 for testing and calibration scopes
shall be eligible. The maximum glazing size shall not be
more than 1100 x 2200 mm (w x h) or 2.42 sqm.

9.139 Providing and fixing panic bar / latch (Double point) 1.00 No. 8366.15 Each 8366.00
fitted with a single body, Trim Latch & Lock on back side
of the Panic Latch of reputed brand and manufacture to
be approved by the Engineer- in- charge, all complete.

9.140 Providing and fixing plain lining with necessary

screws/nuts & bolts/nails including a coat of approved
primer on one face and fixed on wooden /steel frame
work, complete as per direction of Engineer-in-charge.
(Frame work shall be paid for separately)

DSR - 2023 IN MS EXCEL Page 67 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.140.1 12mm thick commercial ply conforming to IS : 1328 1.00 Sqm 1224.65 One Square 1225.00
BWR type. Metre
9.141 Providing and fixing PVC Door Frame of size 50x47mm 1.00 m 573.45 One Running 573.00
with a wall thickness of 5 mm (± 0.2 mm) made out of Metre
single piece extruded PVC profile, with mitred cut joints
and joint with 2nos of PVC bracket of size 190 mm x 100
mm long arms of cross section size 35 x 15mm & self
driven self taping screws, the vertical door profiles to be
reinforced with 40x20mm M.S. rectangular tube of 0.8
mm , including providing EPDM rubber gasket weather
seal throughout the frame, including jointing 5mm PVC
frame strip with PVC solvent cement on the back of the
profile. The door frame to be fixed to the wall using
8x100mm long anchor fasteners complete, all as per
manufacturer's specification and direction of Engineer -
in- charge.

9.142 35 mm thick factory made Solid panel PVC Door shutter

made out of single piece extruded solid PVC profiles, 5
mm (± 0.2mm) thick, having styles & rails (except lock
rail) of size 95 mm x 35 mm x 5 mm, out of which 75
mm shall be flat and 20 mm shall be tapered (on both
side), having one side thickness of 15 mm integrally
extruded on the hinge side of the profile for better
screw holding power, including reinforcing with MS
tube of size 40 mm X 20 mm x 1 mm, joints of styles &
rails to be mitered cut & joint with the help of PVC
solvent cement, self driven self tapping screws & M.S.
rectangular pipes bracket of size 190 mm X 100 mm of
cross section size 35 mm x 17 mm x 1 mm at each
corner. Single piece extruded 5mm thick solid PVC lock
rail of size 115mm X 35mm out of which 75mm to be
flat and 20mm to be tapered at both ends having 15mm
solid core in middle of rail section integrally extruded,
fixing the styles and rails with the help of solvent and
self driven self tapping screws of 125mm X 11mm
including providing 5mm single piece solid PVC
extruded sheet inserted in the door as panel, all
complete as per manufacturer's specification and
direction of Engineer-in-Charge.

9.142.1 Non decorative finish (matt finish). 1.00 Sqm 3997.45 One Square 3997.00
Metre
9.142.2 Decorative finish (wood grained finish). 1.00 Sqm 4713.05 One Square 4713.00
Metre
9.143 Providing and Fixing factory made uPVC door frame, 1.00 m 623.00 One Running 623.00
made of uPVC exturded sections, of size 65 mm x 55 Metre
mm with wall thickness 2.0 mm (± 0.2 mm), corners of
the door frame to be mitred cut and jointed with plastic
brackets and stainless steel screws, reinforcing hinge
side vertical of the frames with PVC profile of Size 28
mm x 30 mm having wall thickness 2 mm (±0.2 mm),
including providing & fixing 3 nos of 125 mm long
stainless steel hinges to the frame, fixing the frame with
jamb with required number & size of anchor dash
fastners, all complete as per manufacturer's
specification and direction of Engineer-in-charge

DSR - 2023 IN MS EXCEL Page 68 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.144 Providing and fixing 37 mm thick factory made PVC 1.00 Sqm 4076.05 One Square 4076.00
door shutter, styles and rails made of PVC hollow Metre
section of size 100 mm x 37 mm with wall thickness 2
mm (± 0.2 mm), with inbuilt bead on one side, styles
and rails mitered cut and joint at the corners by means
of 2 nos of plastic brackets of size 75 mm x 220 mm at
each corner and stainless steel screws, reinforcing the
hinge side of style by inserting PVC profile of size 28
mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm).
Lockrail of size 100 mm x 37 mm, wall thickness 2 mm
(+ 0.2 mm) will be fixed to the vertical styles. Providing
with PVC snapfit beads and panel of size 100 mm x 20
mm, and inserting 2 nos tie bar of 6 mm dia and
fastening with nuts and washers complete, all as per
manufacturer's specification and direction of Engineer-
in-charge.

9.145 Providing and Fixing factory made PVC door frame 1.00 m 763.85 One Running 764.00
made of PVC extruded sections of size 75 mm x 53 mm, Metre
having wall thickness 2.0 mm (± 0.2 mm). Both vertical
sides of the frame reinforced with PVC profile of cross
section size 28 mm x 30 mm x 2 mm thickness (± 0.2
mm) and 75 mm x 200 mm long, including reinforcing
both ends of the top frame with PVC profile. PVC Door
Frame and PVC reinforcement profile to be mitred cut,
jointed and fusion welded together, including providing
and fixing 3 nos of 125 mm long stainless steel hinges to
frame, fixing the frame with jamb with required nos &
sizes of anchor dash fastener, all complete as per
manufacturer's specification and direction of engineer-
in- charge.

9.146 Providing and fixing 37 mm thick factory made PVC 1.00 Sqm 4362.00 One Square 4362.00
Door shutter, styles and rails made of PVC hollow Metre
extruded printed and laminated section having overall
dimension 115 mm x 37 mm with wall thickness 2 mm
(± 0.2 mm) with inbuilt beading on one side, the styles
and rails mitred cut and joint at corners by inserting 2
nos PVC profile reinforcement of size 75 mm x 200 mm
long with cross section size of 28 mm x 30 mm having
wall thickness 2 mm (± 0.2 mm). Styles, rails and
reinforcements to be fusion welded together. Only
hinge side vertical style to be reinforced with PVC
profile reinforcement in full length. Printed and
laminated PVC lock rail of size 110 mm x 37 mm having
wall thickness 2 mm (± 0.2 mm) to be welded
horizontally with the vertical styles after inserting PVC
profile reinforcement as in styles and rails, providing
with PVC snap fit beading, panels of 100 x 20 mm
printed & laminated and inserting 2 nos 6 mm dia bright
steel rod horizontally with both side threaded and
tightened with check nuts and washers complete, all as
per manufacturer's specification and direction of
engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 69 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147A Providing and fixing factory made uPVC glazed/wire
mesh windows/doors comprising of lead free uPVC
multi-chambered frame, sash and mullion/coupler
(where ever required) extruded profiles having
minimum wall thickness of 1.70 mm for Series R1 and
R2 profiles and 2.10 mm for Series R3 and R4 profiles
conforming to EN: 12608 in any shape, colour and
design duly reinforced with galvanized mild steel
section made of required shape & size as per CPWD
Specification, uPVC extruded glazing beads, interlocks
and Inline sash adaptor (where ever required) of
appropriate dimension, EPDM gasket, hardware, SS 304
grade fasteners of minimum 8 mm dia with
countersunk head, comprising of matching polyamide
PA6 grade sleeve for fixing frame to finished wall as per
IS 1367 : Part 1 to 14, plastic packers, plastic caps and
necessary stainless steel screws etc. Profile of frame,
sash & mullion (if required) shall be mitred cut and
fusion welded/mechanically jointed duly sealed at all
corners, including drilling of holes for fixing hardware
and drainage of water etc.

After fixing frame the gap between frame and adjacent

finished wall shall be filled with weather proof silicon
sealant over backer rod pf approved size and quality, all
complete as per approved drawing conforming to
CPWD specification & direction of Engineer-in-Charge.

Section of steel reinforcement and cross sections of

uPVC profiles to be as per design approved by Engineer-
in-Charge. Wire mesh / Glazing of plain/ toughened/
laminated/ double glass unit with / without high
performance coatings as per design requirements and
conforming to IS: 3548 & IS:16231 shall be paid
separately.

Note:- Structural design proof checked from a

Government Engineering Institute, to be provided by
the manufacturer for:
(i) Sites with basic wind speed > 45 m/sec as per IS 875 -
Part 3
(ii) Sites with structure height more than 20m for all
wind speeds.
9.147.A1 Two track two panels sliding window with Aluminium
channel for roller track, wool pile, nylon rollers with SS
304 body.
9.147.A1.1 Using R2 series with frame (40mm & above) x (40mm & 1.00 Sqm 8298.85 One Square 8299.00
above) & sash (25mm & above) x (50mm & above) with Metre
zinc alloy (zamak) powder coated touch locks with hook
(Height upto 1.2 meter)

9.147.A1.2 Using R3 series with frame (55mm & above) x (40mm & 1.00 Sqm 8799.25 One Square 8799.00
above) & sash (30mm & above) x (55mm & above) with Metre
zinc alloy (zamak) powder coated handle on every panel
along with multi-point locking system (Height upto
1.8m)

9.147.A1.3 Using R4 series with frame (64mm & above) x (45mm & 1.00 Sqm 9628.60 One Square 9629.00
above) & sash (44mm & above) x (55mm & above) with Metre
zinc alloy (zamak) powder coated handle on every panel
along with multi-point locking system (Height above
1.8m).

DSR - 2023 IN MS EXCEL Page 70 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147.A2 Two track four panels sliding windows with Aluminium
channel for roller track, wool pile, zinc alloy (zamak)
powder coated handle on three panels along with
multi-point locking system, nylon rollers with SS 304
body.

9.147.A2.1 Using R3 series with frame (55mm & above) x (40mm & 1.00 Sqm 7860.35 One Square 7860.00
above) & sash (30mm & above) x (55mm & above) Metre
(Height upto 1.8m).
9.147.A2.2 Using R4 series with frame (64mm & above) x (45mm & 1.00 Sqm 8579.55 One Square 8580.00
above) & sash (44mm & above) x (55mm & above) Metre
(Height above 1.8m).
9.147.A3 Two and half track three panels sliding window with
two glazed & one wire mesh panels with Aluminium
channel for roller track, wool pile, nylon rollers with SS
304 body.

9.147.A3.1 Using R2 series with frame (65mm & above) x (40mm & 1.00 Sqm 9873.05 One Square 9873.00
above) & glazed sash (25mm & above) x (50mm & Metre
above) & fly screen sash (18mm & above) x (40mm &
above) with zinc alloy (zamak) powder coated touch
locks with hook (Height upto 1.2 meter)

9.147.A3.2 Using R3 series with frame (85mm & above) x (40mm & 1.00 Sqm 9968.70 One Square 9969.00
above) & glazed sash (30mm & above) x (55mm & Metre
above) & fly screen sash (20mm & above) x (50mm &
above) with zinc alloy (zamak) powder coated handle
on every glazed panel along with multi-point locking
system. (Height upto 1.8 meter).

9.147.A4 Three track three panels sliding window with two

glazed & one wire mesh panels with Aluminium channel
for roller track, wool pile, nylon rollers with SS 304
body.

9.147.A4.1 Using R2 series with frame (70mm & above) x (40mm & 1.00 Sqm 10993.55 One Square 10994.00
above) & both glazed and fly screen sash (25mm & Metre
above) x (50mm & above) with zinc alloy (zamak)
powder coated touch locks with hook. (Height upto 1.2
meter).

9.147.A4.2 Using R3 series with frame (98mm & above) x (40mm & 1.00 Sqm 10874.20 One Square 10874.00
above) & both glazed and fly screen sash (30mm & Metre
above) x (55mm & above) with zinc alloy (zamak)
powder coated handle on every glazed panel along with
multi-point locking system, (Height upto 1.8m).

9.147.A4.3 Using R4 series with frame (115mm & above) x (45mm 1.00 Sqm 12372.25 One Square 12372.00
& above) & both glazed and fly screen sash (44mm & Metre
above) x (55mm & above) with zinc alloy (zamak)
powder coated handle on every glazed panel along with
multi-point locking system. (Height above 1.8m)

9.147.A5 Three track three panels sliding window with

Aluminium channel for roller track, wool pile, nylon
rollers with SS 304 body.
9.147.A5.1 Using R2 series with frame (70mm & above) x (40mm & 1.00 Sqm 8748.35 One Square 8748.00
above) & sash (25mm & above) x (50mm & above) with Metre
zinc alloy (zamak) powder coated touch locks with
hook. (Height upto 1.2 meter).

9.147.A5.2 Using R3 series with frame (98mm & above) x (40mm & 1.00 Sqm 8543.60 One Square 8544.00
above) & sash (30mm & above) x (55mm & above) with Metre
zinc alloy (zamak) powder coated handle on two end
panels along with multi-point locking system (Height
upto 1.8 meter).

DSR - 2023 IN MS EXCEL Page 71 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147.A5.3 Using R4 series with frame (115mm & above) x (45mm 1.00 Sqm 9888.35 One Square 9888.00
& above) & sash (44mm & above) x (55mm & above) Metre
with zinc alloy (zamak) powder coated handle on two
end panels along with multi-point locking system.
(Height above 1.8 meter).

9.147.B1 Two track two panels sliding door with Aluminium

channel for roller track, wool pile, zinc alloy (zamak)
powder coated handle on every panel along with multi-
point locking system, adjustable nylon rollers with SS
304 body.

9.147.B1.1 Using R3 series with frame (55mm & above) x (40mm & 1.00 Sqm 8106.30 One Square 8106.00
above) & sash (30mm & above) x (74mm & above). Metre
(Height upto 2.5 meter).
9.147.B1.2 Using R4 series with frame (64mm & above) x (45mm & 1.00 Sqm 7732.85 One Square 7733.00
above) & sash (44mm & above) x (85mm & above). Metre
(Height above 2.5 meter).
9.147.B2 Two track four panels sliding door with Aluminium
channel for roller track, wool pile, zinc alloy (zamak)
powder coated handle on three panels along with
multi-point locking system, adjustable nylon rollers with
SS 304 body.

9.147.B2.1 Using R3 series with frame (55mm & above) x (40mm & 1.00 Sqm 7345.35 One Square 7345.00
above) & sash (30mm & above) x (74mm & above). Metre
(Height upto 2.5 meter).
9.147.B2.2 Using R4 series with frame (64mm & above) x (45mm & 1.00 Sqm 7196.70 One Square 7197.00
above) & sash (44mm & above) x (85mm & above). Metre
(Height above 2.5 meter).
9.147.B3 Three track three panels sliding door with two glazed &
one wire mesh panels with Aluminium channel for roller
track, wool pile, zinc alloy (zamak) powder coated
handle on two panels along with multi-point locking
system, adjustable nylon rollers with SS 304 body.

9.147.B3.1 Using R3 series with frame (98mm & above) x (40mm & 1.00 Sqm 10078.95 One Square 10079.00
above) & both glazed and fly screen sash (30mm & Metre
above) x (74mm & above). (Height upto 2.5 meter).
9.147.B3.2 Using R4 series with frame (115mm & above) x (45mm 1.00 Sqm 9894.80 One Square 9895.00
& above) & both glazed and fly screen sash (44mm & Metre
above) x (85mm & above). (Height above 2.5 meter).

9.147.B4 Three track three panels sliding door with Aluminium

channel for roller track, wool pile, zinc alloy (zamak)
powder coated handle on two panels along with multi-
point locking system, adjustable nylon rollers with SS
304 body.

9.147.B4.1 Using R3 series with frame (98mm & above) x (40mm & 1.00 Sqm 8287.05 One Square 8287.00
above) & sash (30mm & above) x (74mm & above). Metre
(Height upto 2.5 meter).
9.147.B4.2 Using R4 series with frame (115mm & above) x (45mm 1.00 Sqm 7943.95 One Square 7944.00
& above) & sash (44mm & above) x (85mm & above). Metre
(Height above 2.5 meter).
9.147.C1 Fixed window / ventilator without mullion / transom
9.147.C1.1 Using R1 series with frame (33mm & above ) x (35mm & 1.00 Sqm 8247.25 One Square 8247.00
above). (Height upto 0.90 meter) Metre
9.147.C1.2 Using R2 series with frame (39mm & above ) x (39mm & 1.00 Sqm 8054.75 One Square 8055.00
above). (Height upto 1.2 meter) Metre
9.147.C1.3 Using R3 series with frame (55mm & above) x (45mm & 1.00 Sqm 7080.05 One Square 7080.00
above). (Height upto 2.5 meter) Metre

DSR - 2023 IN MS EXCEL Page 72 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147.C1.4 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 6032.85 One Square 6033.00
above). (Height above 2.5 meter) Metre
9.147.C2 Fixed window / ventilator with mullion / transom.
9.147.C2.1 Using R1 series with frame (33mm & above ) x (35mm & 1.00 Sqm 9155.20 One Square 9155.00
above) & mullion (33mm & above) x (50mm & above). Metre
(Height upto 0.90 meter)
9.147.C2.2 Using R2 series with frame (39mm & above ) x (39mm & 1.00 Sqm 8765.40 One Square 8765.00
above) & mullion (39mm & above) x (60mm & above). Metre
(Height upto 1.2 meter)
9.147.C2.3 Using R3 series with frame (55mm & above ) x (45mm & 1.00 Sqm 7827.75 One Square 7828.00
above) & mullion (55mm & above) x (65mm & above). Metre
(Height upto 2.5 meter)
9.147.C2.4 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 6528.80 One Square 6529.00
above) & mullion (64mm & above) x (70mm & above). Metre
(Height above 2.5 meter)
9.147.D1 Ventilator Casement window single panel with or
without fixed panel with S S. 304 friction hinges as per
size and weight of sash, single point locking zinc alloy
(zamak) powder coated handles.

9.147.D1.1Using R1 series with frame (33mm & above ) x (35mm & 1.00 Sqm 13201.20 One Square 13201.00
above) & sash /mullion (33mm & above) x (50 mm & Metre
above). (Height upto 0.90 meter).
9.147.D1.2Using R2 series with frame (39mm & above ) x (39mm & 1.00 Sqm 12254.90 One Square 12255.00
above) & sash /mullion (39mm & above) x (60mm & Metre
above). (Height upto 1.2 meter)
9.147.D1.3Using R3 series with frame (55mm & above ) x (45mm & 1.00 Sqm 11919.85 One Square 11920.00
above) & sash /mullion (55mm & above) x (65mm & Metre
above). (Height above 1.2 meter)
9.147.E1 Casement window single panel with S.S. 304 friction
hinges as per size and weight of sash, multi-point
locking system, zinc alloy (zamak) powder coated
handles.

9.147.E1.1 Using R2 series with frame (39mm & above) x (39mm & 1.00 Sqm 14449.25 One Square 14449.00
above) & sash (39mm & above) x (60mm & above). Metre
(Height upto 1.2 meter)
9.147.E1.2 Using R3 series with frame (55mm & above ) x (45mm & 1.00 Sqm 13387.15 One Square 13387.00
above) & sash (55mm & above) x (65mm & above). Metre
(Height upto 1.8 meter)
9.147.E1.3 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 14587.05 One Square 14587.00
above) & sash (64mm & above) x (70mm & above). Metre
(Height above 1.8 meter)
9.147.E2 Casement window double panels with fixed mullion
with S.S. 304 friction hinges as per size and weight of
sash, multi-point locking system, zinc alloy (zamak)
powder coated handles.

9.147.E2.1 Using R2 series with frame (39mm & above ) x (39mm & 1.00 Sqm 13078.70 One Square 13079.00
above) & sash (39mm & above) x (60mm & above) & Metre
mullion (39mm & above) x (60mm & above). (Height
upto 1.2 meter).

9.147.E2.2 Using R3 series with frame (55mm & above ) x (45mm & 1.00 Sqm 12472.95 One Square 12473.00
above) & sash (55mm & above) x (65mm & above) & Metre
mullion (55mm & above) x (65mm & above). (Height
upto 1.8 meter).

9.147.E2.3 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 13477.10 One Square 13477.00
above) & sash (64mm & above) x (70mm & above) & Metre
mullion (64mm & above) x (70mm & above). (Height
above 1.8 meter).

DSR - 2023 IN MS EXCEL Page 73 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147.E3 Casement window double panels with French (False)
Mullion with S.S. 304 friction hinges as per size and
weight of sash, multi-point locking system, zinc alloy
(zamak) powder coated handles.

9.147.E3.1 Using R2 series with frame (39mm & above ) x (39mm & 1.00 Sqm 11715.95 One Square 11716.00
above) & sash (39mm & above) x (60mm & above) & Metre
French (False) mullion (39mm & above) x (60mm &
above). (Height upto 1.2 meter)

9.147.E3.2 Using R3 series with frame (55mm & above ) x (45mm & 1.00 Sqm 11466.80 One Square 11467.00
above) & sash (55mm & above) x (65mm & above) & Metre
French (False) mullion (55mm & above) x (60mm &
above), (Height upto 1.8 meter).

9.147.E3.3 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 12496.30 One Square 12496.00
above) & sash (64mm & above) x (70mm & above) & Metre
French (False) mullion (64mm & above) x (60mm &
above). (Height above 1.8 meter)

9.147.E4 Casement cum fixed panel window having one single

casement panel & one fixed panel with S.S. 304 friction
hinges as per size and weight of sash, multi point
locking system, zinc alloy (zamak) powder coated
handles.

9.147.E4.1 Using R2 series with frame (39mm & above ) x (39mm & 1.00 Sqm 9870.15 One Square 9870.00
above) & sash (39mm & above) x (60mm & above) & Metre
mullion (39mm & above) x (60mm & above). (Height
upto 1.2 meter; each openable shutter upto 0.8m
width)

9.147.E4.2 Using R3 series with frame (55mm & above ) x (45mm & 1.00 Sqm 9308.00 One Square 9308.00
above) & sash (55mm & above) x (65mm & above) & Metre
mullion (55mm & above) x (65mm & above). (Height
upto 1.8 meter; each openable shutter upto 0.8m
width)

9.147.E4.3 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 10212.60 One Square 10213.00
above) & sash (64mm & above) x (70mm & above) & Metre
mullion (64mm & above) x (70mm & above). (Height
above 1.8 meter; each openable shutter upto 0.8m
width)

9.147.E5 Casement cum fixed panel window having single

casement panel at both ends & middle fixed panel with
S.S 304 friction hinges as per size and weight of sash,
multi-point locking system, zinc alloy (zamak) powder
coated handles.

9.147.E5.1 Using R2 series with frame (39mm & above) x (39mm & 1.00 Sqm 10474.05 One Square 10474.00
above) & sash (39mm & above) x (60mm & above) & Metre
mullion (39mm & above) x (60mm & above). (Height
upto 1.2 meter; each openable shutter upto 0.8m
width)

9.147.E5.2 Using R3 series with frame (55mm & above) x (45mm & 1.00 Sqm 10051.20 One Square 10051.00
above) & sash (55mm & above) x (65mm & above) & Metre
mullion (55mm & above) x (65mm & above). (Height
upto 1.8 meter; each openable shutter upto 0.8m
width)

9.147.E5.3 Using R4 series with frame (64mm & above ) x (50mm & 1.00 Sqm 10200.75 One Square 10201.00
above) & sash (64mm & above) x (70mm & above) & Metre
mullion (64mm & above) x (70mm & above). (Height
above 1.8 meter; each openable shutter upto 0.8m
width)

DSR - 2023 IN MS EXCEL Page 74 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147.E6 Casement Window with Double Rebate Frame with one
Side Hung Glazed Panel and one Side Hung wire mesh
Panel with S.S. 304 friction hinges as per size and
weight of sash, multi-point locking system, zinc alloy
(zamak) powder coated handles on both glazed and fly
screen panel

9.147.E6.1 Using R3 series with frame (110mm & above ) x (45mm 1.00 Sqm 22785.35 One Square 22785.00
& above) & glazed sash (55mm & above) x (65mm & Metre
above) & fly screen sash (30mm & above) x (55mm &
above) & metal grill (if required to be paid separately).
(Height upto 1.8 meter)

9.147.E7 Casement Window with Double Rebate Frame with two

Side Hung Glazed Panel and two Side Hung wire mesh
Panel and Fixed Mullion with S.S. 304 friction hinges as
per size and weight of sash, multi-point locking system,
zinc alloy (zamak) powder coated handles on both
glazed and fly screen panel.

9.147.E7.1 Using R3 series with frame (110mm & above ) x (45mm 1.00 Sqm 20576.30 One Square 20576.00
& above) & glazed sash (55mm & above) x (65mm & Metre
above) & fly screen sash (30mm & above) x (55mm &
above) & mullion (55mm & above) x (65mm & above) &
metal grill (if required to be paid separately). (Height
upto 1.8 meter)

9.147.E8 Casement Window with Double Rebate Frame with two

Side Hung Glazed Panel on outside and two Side Hung
wire mesh Panel on inside and French (False) Mullion
with S.S. 304 friction hinges as per size and weight of
sash, multi-point locking system, zinc alloy (zamak)
powder coated handles with shoot bolt on both glazed
and fly screen panel.

9.147.E8.1 Using R3 series with frame (110mm & above ) x (45mm 1.00 Sqm 19047.60 One Square 19048.00
& above) & glazed sash (55mm & above) x (65mm & Metre
above) & fly screen sash (30mm & above) x (55mm &
above) & French (False) mullion (55mm & above) x
(60mm & above) & metal grill (if required to be paid
separately). (Height upto 1.8 meter)

9.147.F1 Casement door single panel with zinc alloy (zamak) 3D

hinges, multi-point locking system with cylinder, zinc
alloy (zamak) powder coated handles on both sides.

9.147.F1.1 Using R3 series with frame (55 mm & above) x (50mm & 1.00 Sqm 12496.05 One Square 12496.00
above) & sash (55 mm & above) x (85mm & above) Metre
(Height upto 2.5 meter).
9.147.F1.2 Using R4 series with frame (64 mm & above) x (55mm & 1.00 Sqm 12454.40 One Square 12454.00
above) & sash (64 mm & above) x (100mm & above). Metre
(Height above 2.5 meter).
9.147.F2 Casement door double panel with French (False)
Mullion with zinc alloy (zamak) 3D hinges, multi-point
locking system with cylinder, zinc alloy (zamak) powder
coated handles on both sides.

9.147.F2.1 Using R3 series with frame (55 mm & above) x (50mm & 1.00 Sqm 11903.75 One Square 11904.00
above) & sash (55 mm & above) x (85mm & above) & Metre
French (False) mullion (55 mm & above) x (60mm &
above). (Height upto 2.5 meter).

9.147.F2.2 Using R4 series with frame (64 mm & above) x (55mm & 1.00 Sqm 11818.95 One Square 11819.00
above) & sash (64 mm & above) x (100mm & above) & Metre
French (False) mullion (64 mm & above) x (60mm &
above). (Height above 2.5 meter).

DSR - 2023 IN MS EXCEL Page 75 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.147.F3 Casement Door with Double Rebate Frame with one
Side Hung Glazed Panel and one Side Hung wire mesh
Panel with zinc alloy (zamak) 3D hinges, multi- point
locking system with cylinder, zinc alloy (zamak) powder
coated handles on both sides of glazed panel and zinc
alloy (Zamak) powder coated handle along with multi-
point locking system on one side of fly screen panel.

9.147.F3.1 Using R3 series with frame (110mm & above) x (45mm 1.00 Sqm 19994.40 One Square 19994.00
& above) & glazed sash (55mm & above) x (85mm & Metre
above) & fly screen sash (55mm & above) x (65mm &
above). (Height upto 2.5 meter).

9.148 Providing and fixing stainless steel (SS-304 grade)

friction hinges to the side/top hung uPVC windows, of
approved quality, with necessary stainless steel screws
etc. as per direction of Engineer-in-charge.

9.148.1 200 x 19 x 1.9 mm 1.00 No. 381.30 Each 381.00

9.148.2 250 x 19 x 1.9 mm 1.00 No. 422.55 Each 423.00
9.148.3 300 x 19 x 1.9 mm 1.00 No. 459.55 Each 460.00
9.148.4 350 x 19 x 1.9 mm 1.00 No. 624.60 Each 625.00
9.148.5 400 x 19 x 1.9 mm 1.00 No. 610.35 Each 610.00
9.149 Providing and fixing casement handle made of zinc 1.00 No. 231.05 Each 231.00
alloyed (white powder coated) for uPVC casement
window with necessary screws etc. complete.
9.150 Providing and fixing zinc alloyed (white powder coated) 1.00 No. 204.00 Each 204.00
touch lock for uPVC sliding window with necessary
screws etc. complete.
9.151 Providing and fixing steel roller for uPVC sliding window 1.00 No. 115.80 Each 116.00
with necessary screws etc. complete.
9.152 Providing and fixing steel roller for uPVC sliding door 1.00 No. 185.50 Each 186.00
with necessary screws etc. complete.
9.153 Providing and fixing steel (white power coated) crescent 1.00 No. 198.30 Each 198.00
lock for uPVC sliding window/ door with necessary
screws etc. complete.
9.154 Providing and fixing frame work for partitions/ wall 1.00 Kg 166.80 One Kilogram 167.00
lining etc. made of 50x50x1.6 mm hollow MS tube,
placed along the walls, ceiling and floor in a grid pattern
with spacing @ 60 cm centre to centre both ways
(vertically & horizontally) or at required spacing near
opening, with necessary welding at junctions and fixing
the frame to wall/ ceiling/ floors with steel dash
fasteners of 8 mm dia, 75 mm long bolt, including
making provision for opening for doors, windows,
electrical conduits, switch boards etc., including
providing with two coats of approved steel primer etc.
complete, all as per direction of Engineer-in-charge.

9.155 Providing and fixing panelling or panelling and glazing in 1.00 Sqm 1956.90 One Square 1957.00
panelled or panelled and glazed shutters for doors, Metre
windows and clerestory windows ( area of opening for
panel inserts excluding portion inside grooves or
rebated to be measured). Panelling for panelled and
glazed shutters 25mm to 40mm thick: Pre-laminated
with decorative lamination on both side exterior Grade
- I MDF Board 12 mm thick confirming to IS:14587

DSR - 2023 IN MS EXCEL Page 76 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.156 Providing and fixing Pre -laminated medium density
fibre board exterior grade (Grade-I) IS:14587:1998
marked, to frame, backing or studding with screws etc.
complete ( Frames, backing or studding to be paid
separately).

9.156.1 Pre-laminated with decorative lamination on both side 1.00 Sqm 1031.50 One Square 1032.00
exterior Grade - I MDF Board 12 mm thick confirming to Metre
IS:14587
9.156.2 Pre-laminated with decorative lamination on both side 1.00 Sqm 1248.00 One Square 1248.00
exterior Grade - I MDF Board 18 mm thick confirming to Metre
IS:14587
9.157 Providing and fixing Pre-laminated medium density
fibre board IS: 14587:1998 marked, with one side
decorative lamination other side balancing lamination
Grade-I(exterior grade) in shelves with screws and
fittings wherever required, edges to be sealed with PVC
edge bending tape 2.00 mm thick of approved brand
(fittings to be paid separately).

9.157.1 Pre-laminated with decorative lamination one side and 1.00 Sqm 1415.70 One Square 1416.00
other side balancing lamination exterior Grade - I MDF Metre
Board 18 mm thick confirming to IS:14587
9.157.2 Pre-laminated with decorative lamination one side and 1.00 Sqm 1874.70 One Square 1875.00
other side balancing lamination exterior Grade - I MDF Metre
Board 25 mm thick confirming to IS:14587
9.158 Providing and fixing in wall lining medium density fibre
board IS: 14587:1998 marked, Pre-laminated one side
decorative lamination and other side balancing
lamination, with necessary fixing arrangement and
screws etc. complete.

9.158.1 12 mm thick. 1.00 Sqm 1212.75 One Square 1213.00

Metre
9.158.2 18 mm thick. 1.00 Sqm 1436.55 One Square 1437.00
Metre
9.158.3 25 mm thick. 1.00 Sqm 1912.25 One Square 1912.00
Metre
9.159 Providing and fixing 25mm thick pre-laminated medium 1.00 Sqm 2135.25 One Square 2135.00
density fibre board exterior grade ( Grade-I) Metre
IS:14587:1998 marked with one side decorative and
other side balancing lamination for cupboard shutters
edges to be sealed with PVC edge bending tape 2.00
mm thick of approved brand including ISI marked nickel
plated bright finishing M.S. piano hinges conforming to
IS:3818 marked with necessary screw etc all complete.

9.160 Providing and fixing skirting with Pre-laminated medium

density fibre board exterior grade (Grade-I) conforming
to IS: 14587:1998 marked, with (one side decorative
and other side balancing lamination and edges to be
sealed with PVC edge bending tape 2.00 mm thick of
approved brand with necessary fixing arrangements
and screws, including drilling necessary holes for rawl
plugs etc. all complete.

9.160.1 18 mm thick. 1.00 Sqm 2076.65 One Square 2077.00

Metre
9.160.2 25 mm thick. 1.00 Sqm 2552.40 One Square 2552.00
Metre

DSR - 2023 IN MS EXCEL Page 77 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.161 Providing and fixing fire resistant door frame of section 1.00 m 2202.90 One Metre 2203.00
50 x 60 mm on horizontal side & 35 x 60 mm on vertical
sides having built in rebate made out of 1.6 mm thick GI
sheet (Zinc coating not less than 120 gm/sqm) suitable
for mounting 120 minutes Fire Rated Glazed Door
Shutters. The frame shall be filled with mineral wood
Insulation having density minimum 96Kg/sqm. The
frame will have a provision of G.I. anchor fastners 14
nos (5 each on vertical style & 4 on horizontal style of
size M10 x 80) suitable for fixing in the opening along
with factory made template for SS ball bearing hinges
of size 100x89x3 mm for fixing of fire rated glazed
shutter. The fram shall be finished with an approved fire
resistant primer or powder coating of not less than 30
micron in desired shade as per the directions of
Engineer -in- Charge. (Cost of SS ball bearing hinges is
excluded).

9.162 Providing and fixing 60 mm thick glazed fire resistant 1.00 Sqm 12017.90 One Square 12018.00
door shutters of 120 min Fire rating confirming to Metre
IS:3614 (Part II) or EN1634-1:1999, tested and certified
as per laboratory approved by Engineer-in-charge, with
suitable mounting on door frame, consisting of vertical
styles, top rail & side rail 60 mm x 60 mm wide and
bottom rail of 110 mm x 60 mm made out of 1.6mm
thick G.I. sheet (zinc coating not less than 120gm/sqm)
duly filled mineral wool insulation having density min
96 kg/ cum and fixing with necessary stainless steel ball
bearing hinges of size 100x89x3mm of approved make,
including applying a coat of approved fire resistant
primer or powder coating not less than 30 micron etc all
complete as per direction of Engineer-in-charge
(panelling to be paid for seperately).

9.163 Providing and fixing non load bearing fixed frame for 1.00 m 2202.90 One running 2203.00
fire resistant glazed Partition for 120 minutes Fire Metre
Rating, made out to a profile of dimension 60mm x 70
mm of 1.6 mm thick galvanised steel sheet as per test
evidence suitable for fixing fire rated glass for 120
minutes of both integrity & radiation control (EW120) &
minimum 20 minutes of insulation (EI20).The profile has
to be fixed to the supporting construction by means of
anchor fasteners of size M10 x 80, every 150 mm from
the edges and every 500 mm (approx) c/c. Linear
measurement of frame shall be measured for payment.
The frame shall be filled with mineral wool insulation of
density min 96kg/ cum and finished with a approved
fire resistant primer or powder coating of not less than
30 micron in desired shade as per NBC 2016, IS 16231
(Part 3):2016 and directions of Engineer - in- charge.

9.165 Providing and fixing bright /matt finished Stainless Steel

handles of approved quality & make with necessary
screws etc all complete.
9.165.1 125mm 1.00 No. 119.20 Each 119.00
9.165.2 100mm 1.00 No. 90.45 Each 90.00
9.165.3 75mm 1.00 No. 58.75 Each 59.00

DSR - 2023 IN MS EXCEL Page 78 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.166 Providing and fixing 18 mm thick both side Pre-
laminated cement bonded wood particle board as per
IS : 15786:2008 of approved brand and shade with
suitable full threaded steel screws etc. in partitions,
boxes, shelves, racks and cupboard, kitchen cabinet
under kitchen counter etc. all complete as per direction
of Engineer-in-charge (Note: Fittings to be paid
separately).

9.166.1 18 mm thick. 1.00 Sqm 1362.30 One Square 1362.00

Metre
9.167 Providing and fixing 6 mm thick both sides Pre- 1.00 Sqm 1010.60 One Square 1011.00
laminated cement bonded wood particle board as per Metre
IS : 15786:2008 of approved brand and shade with
suitable full threaded steel screws etc. on the backing
of racks, drawer, cupboard, kitchen cabinet under
kitchen counter etc. all complete as per direction of
Engineer-in-charge.

9.168 Providing and fixing cuboard shutter with 19 mm thick 1.00 Sqm 2829.25 One Square 2829.00
one side decorative and other side balancing lamination Metre
factory pressed BWP grade marine ply as per IS 710 of
approved brand including 2 mm thick PVC edege
banding tape with hot glue by edege bending machine
etc. with auto closing spring loaded hinges (hydraulic
type) etc. complete as per direction of Engineer-in-
charge. (Payment of providing and fixing auto closing
hinges shall be paid separately)

9.169 Providing and fixing 19 mm thick both side balancing 1.00 Sqm 2593.15 One Square 2593.00
lamination factory pressed BWP grade marine ply as per Metre
IS 710 of approved brand boxes, shelves, racks, almirah,
cupboard and drawer etc. including necessary nails,
screws etc. complete as per direction of Engineer-in-
charge.

9.170 Providing and fixing stainless steel fancy handle of

approved make fixed with SS screws etc. complete as
per direction of Engineer-in-charge.
9.170.1 200 mm 1.00 No. 186.65 Each 187.00
9.171 Providing and fixing stainless steel soft closing spring 1.00 No. 272.00 Each 272.00
hinges at 0 degree hinges (hydrarlic type) of approved
make/brand to cupboard shutters with full threaded
steel screws including making necessary recess in board
and finished etc. complete as per direction of Engineer-
in-charge.

9.172 Providing and fixing stainless steel soft closing heavy 1.00 sets 885.10 One Set 885.00
type telescopic drawer channels of approved make 500
mm long with screws etc. complete as per directions of
Engineer- in-charge.

DSR - 2023 IN MS EXCEL Page 79 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
9.173 Providing and fixing ready made 304 grade stainless 1.00 Kg 533.25 One Kilogram 533.00
steel Modular kitchen basket and accessories such as
right angle basket (Plain Cup & Saucer, plant, Partition,
Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner
set basket, kitchen grain basket, Multipurpose basket as
per site requirement including finishing (wherever
required) and fittings. The same shall be fixed with
necessary stainless steel nuts & bolst, Stainless Steel
screws & telescopic channel etc. as per direction of
Engineer-in-charge. (For payment purpose only weight
of Stainless steel basket shall be considered excluding
weight of all fixing accessories such as nuts, bolts,
fasteners telescopic basket channels etc. Payment of
providing and fixing telescopic channel shall be paid
separately)

9.174 Providing and fixing 2 mm thick 16 to 19 mm wide PVC 1.00 m 43.80 One running 44.00
edge binding tape of approved quality for Metre
cuboard/wardrobe shutters including necessary
synthetic resin hot pressed to edges on binding
machine etc. complete as per direction of Engineer-in-
charge.

Total of the Sub-Head - Wood And P.V.C Work : 1941900.00

Sub-Head : Steel Work
10.1 Structural steel work in single section, fixed with or 1.00 Kg 117.35 One Kilogram 117.00
without connecting plate,including cutting, hoisting,
fixing in position and applying a priming coat of
approved steel primer all complete

10.2 Structural steel work riveted, bolted or welded in built 1.00 Kg 133.70 One Kilogram 134.00
up sections, trusses and framed work, including cutting,
hoisting, fixing in position and applying a priming coat
of approved steel primer all complete.

10.3 Providing and fixing in position collapsible steel shutters 1.00 Sqm 11439.60 One Square 11440.00
with vertical channels 20x10x2 mm and braced with flat Metre
iron diagonals 20x5 mm size, with top and bottom rail
of T-iron 40x40x6 mm, with 40 mm dia steel pulleys,
complete with bolts, nuts, locking arrangement,
stoppers, handles, including applying a priming coat of
approved steel primer.

10.4 Providing and fixing 1 mm thick M.S. sheet sliding- 1.00 Sqm 6566.20 One Square 6566.00
shutters, with frame and diagonal braces of 40x40x6 Metre
mm angle iron, 3 mm M.S. gusset plates at the junctions
and corners, 25 mm dia pulley, 40x40x6 mm angle and
T- iron guide at the top and bottom respectively,
including applying a priming coat of approved steel
primer.

10.5 Providing and fixing 1mm thick M.S. sheet door with
frame of 40x40x6 mm angle iron and 3 mm M.S. gusset
plates at the junctions and corners, all necessary fittings
complete, including applying a priming coat of
approved steel primer.

10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces 1.00 Sqm 5804.35 One Square 5804.00
Metre
10.5.2 Using flats 30x6mm for diagonal braces and central 1.00 Sqm 5563.75 One Square 5564.00
cross piece Metre

DSR - 2023 IN MS EXCEL Page 80 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
10.6 Supplying and fixing rolling shutters of approved make,
made of required size M.S. laths, interlocked together
through their entire length and jointed together at the
end by end locks, mounted on specially designed pipe
shaft with brackets, side guides and arrangements for
inside and outside locking with push and pull operation
complete, including the cost of providing and fixing
necessary 27.5 cm long wire springs manufactured from
high tensile steel wire of adequate strength conforming
to IS: 4454 - part 1 and M.S. top cover of required
thickness for rolling shutters.

10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover. 1.00 Sqm 3653.20 One Square 3653.00
Metre
10.6.2 80x1.20 mm M.S. laths with 1.20 mm thick top cover. 1.00 Sqm 3307.05 One Square 3307.00
Metre
10.6.3 80x0.90 mm M.S. laths with 0.90 mm thick top cover. 1.00 Sqm 3191.35 One Square 3191.00
Metre
10.7 Providing and fixing ball bearing for rolling shutters. 1.00 No. 492.35 Each 492.00
10.8 Extra for providing mechanical device chain and crank
operation for operating rolling shutters.
10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area. 1.00 Sqm 1281.35 One Square 1281.00
Metre
10.8.2 Exceeding 16.80 sqm in area. 1.00 Sqm 1181.80 One Square 1182.00
Metre
10.9 Extra for providing grilled rolling shutters manufactured 1.00 Sqm 768.25 One Square 768.00
out of 8 mm dia M.S. bar instead of laths as per design Metre
approved by Engineer-in- charge, (area of grill to be
measured).

10.10 Fixing standard steel glazed doors, windows and

ventilators in walls, including fixing of float glass panes
with glazing clips and special metalsash putty of
approved make, or metal beading with screws, (only
steel windows, glass panes cut to size and glazing clips
or metal beading with screws, shall be supplied by
department free of cost.

10.10.1 Fixing with 15x3 mm lugs 10 cm long embedded in 1.00 Kg 82.45 One Kilogram 82.00
cement concrete block 15x10x10 cm of C.C. 1:3:6 (1
Cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size).

10.10.2 Fixing with carbon steel galvanised dash fastener of 1.00 Kg 40.80 One Kilogram 41.00
required dia and size (to be paid for separately).
10.11 Providing and fixing factory made ISI marked steel
glazed doors, windows and ventilators, side /top
/centre hung, with beading and all members such as
F7D,F4B, K11 B and K12 B etc. complete of standard
rolled steel sections, joints mitred and flash butt welded
and sash bars tenoned and riveted, including providing
and fixing of hinges, pivots, priming coat of approved
steel primer, but excluding the cost of other fittings,
glass panes complete all as per approved design,
(sectional weight of only steel members shall be
measured for payment).

10.11.1 Fixing with 15x3 mm lugs 10 cm long embedded in 1.00 Kg 131.05 One Kilogram 131.00
cement concrete block 15x10x10 cm of C.C. 1:3:6 (1
Cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size)

10.11.2 Fixing with carbon steel galvanised dash fastener of 1.00 Kg 128.25 One Kilogram 128.00
required dia and size (to be paid for separately)

DSR - 2023 IN MS EXCEL Page 81 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
10.12 Extra for providing and fixing steel beading of size 10 x 1.00 m 49.60 One Metre 50.00
10 x 1.6 mm (box type), approved shape and section
with screws instead of glazing clips and metal sash
putty, in steel doors, windows, ventilators and
composite units.

10.13 Providing and fixing T-iron frames for doors, windows

and ventilators of mild steel Tee-sections, joints mitred
and welded, including fixing of necessary butt hinges
and screws and applying a priming coat of approved
steel primer.

10.13.1 Fixing with 15x3 mm lugs 10 cm long embedded in 1.00 Kg 141.70 One Kilogram 142.00
cement concrete block 15x10x10 cm of C.C. 1:3:6 (1
Cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size).

10.13.2 Fixing with carbon steel galvanised dash fastener of 1.00 Kg 136.00 One Kilogram 136.00
required dia and size (to be paid for separately)
10.14 Providing and fixing pressed steel door frames
conforming to IS: 4351, manufactured from commercial
mild steel sheet of 1.60 mm thickness, including hinges,
jamb, lock jamb, bead and if required angle threshold of
mild steel angle of section 50x25 mm, or base ties of
1.60 mm, pressed mild steel welded or rigidly fixed
together by mechanical means, including M.S. pressed
butt hinges 2.5 mm thick with mortar guards, lock
strike-plate and shock absorbers as specified and
applying a coat of approved steel primer after pre-
treatment of the surface as directed by Engineer-in-
charge:

10.14.1 Profile B
10.14.1.1 Fixing with adjustable lugs with split end tail to each 1.00 m 583.30 One Metre 583.00
jamb.
10.14.1.2 Fixing with carbon steel galvanised dash fastener of 1.00 m 570.40 One Metre 570.00
required dia and size (to be paid for separately).
10.14.2 Profile C
10.14.2.1 Fixing with adjustable lugs with split end tail to each 1.00 m 611.75 One Metre 612.00
jamb.
10.14.2.2 Fixing with carbon steel galvanised dash fastener of 1.00 m 598.85 One Metre 599.00
required dia and size (to be paid for separately).
10.14.3 Profile E
10.14.3.1 Fixing with adjustable lugs with split end tail to each 1.00 m 640.20 One Metre 640.00
jamb.
10.14.3.2 Fixing with carbon steel galvanised dash fastener of 1.00 m 627.30 One Metre 627.00
required dia and size (to be paid for separately).
10.15 Providing and fixing M.S. Tubular frames for doors,
windows, ventilators and cupboard with rectangular/ L-
Type sections, made of 1.60 mm thick M.S. Sheet, joints
mitred, welded and grinded finish, with profiles of
required size, including fixing of necessary butt hinges
and screws and applying a priming coat of approved
steel primer.

10.15.1 Fixing with 15x3 mm lugs 10 cm. long embedded in 1.00 Kg 195.20 One Kilogram 195.00
cement concrete block 15x10x10 cm of C.C. 1:3:6 (1
Cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size).

10.15.2 Fixing with carbon steel galvanised dash fastener of 1.00 Kg 181.25 One Kilogram 181.00
required dia and size (to be paid for separately).

DSR - 2023 IN MS EXCEL Page 82 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
10.16 Steel work in built up tubular (round, square or
rectangular hollow tubes etc.) trusses etc., including
cutting, hoisting, fixing in position and applying a
priming coat of approved steel primer, including
welding and bolted with special shaped washers etc.
complete.

10.16.1 Hot finished welded type tubes. 1.00 Kg 194.40 One Kilogram 194.00

10.16.2 Hot finished seamless type tubes. 1.00 Kg 206.35 One Kilogram 206.00

10.16.3 Electric resistance or induction butt welded tubes. 1.00 Kg 194.40 One Kilogram 194.00

10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm 1.00 No. 226.00 Each 226.00
dia M.S. bar, bent to shape with hooked ends in R.C.C.
slabs or beams during laying, including painting the
exposed portion of loop, all as per standard design
complete.

10.18 Providing and fixing circular/ Hexagonal cast iron or 1.00 No. 220.65 Each 221.00
M.S. sheet box for ceiling fan clamp, of internal dia 140
mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet
with its top surface hacked for proper bonding, top lid
shall be screwed into the cast iron/ M.S. sheet box by
means of 3.3 mm dia round headed screws, one lock at
the corners. Clamp shall be made of 12 mm dia M.S. bar
bent to shape as per standard drawing.

10.19 Providing and fixing mild steel round holding down 1.00 Kg 97.20 One Kilogram 97.00
bolts with nuts and washer plates complete.
10.20 Providing and fixing bolts including nuts and washers 1.00 Kg 159.35 One Kilogram 159.00
complete.
10.21 Providing and fixing M.S. rivets of sizes in position. 1.00 Kg 278.30 One Kilogram 278.00

10.22 Welding by gas or electric plant including transportation 1.00 cm 3.70 One 4.00
of plant at site etc. complete. Centimetre
10.25 Steel work welded in built up sections/ framed work,
including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer using
structural steel etc. as required.

10.25.1 In stringers, treads, landings etc. of stair cases, including 1.00 Kg 123.60 One Kilogram 124.00
use of chequered plate wherever required, all
complete.
10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, 1.00 Kg 172.60 One Kilogram 173.00
gates and similar works.
10.26 Providing and fixing hand rail of approved size by
welding etc. to steel ladder railing, balcony railing,
staircase railing and similar works, including applying
priming coat of approved steel primer.

10.26.1 M.S. tube. 1.00 Kg 196.80 One Kilogram 197.00

10.26.2 E.R.W. tubes. 1.00 Kg 205.75 One Kilogram 206.00

10.26.3 G.I. pipes 1.00 Kg 203.05 One Kilogram 203.00

DSR - 2023 IN MS EXCEL Page 83 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
10.27 Providing and fixing carbon steel galvanised (minimum
coating 5 micron) dash fastener of 10 mm dia double
threaded 6.8 grade (yield strength 480 N/mm2),
counter sunk head, comprising of 10 mm dia polyamide
PA 6 grade sleeve, including drilling of hole in frame ,
concrete/ masonry, etc. as per direction of Engineer-in-
charge.

10.27.1 10 x 60 mm 1.00 No. 131.10 Each 131.00

10.27.2 10 x 80 mm 1.00 No. 137.65 Each 138.00
10.27.3 10 x 120 mm 1.00 No. 170.95 Each 171.00
10.27.4 10 x 140 mm 1.00 No. 182.20 Each 182.00
10.27.5 10 x 160 mm 1.00 No. 224.50 Each 225.00
10.28 Providing and fixing stainless steel (Grade 304) railing 1.00 Kg 772.40 One Kilogram 772.00
made of Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and making
curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c
fixing the railing with necessary accessories & stainless
steel dash fasteners , stainless steel bolts etc., of
required size, on the top of the floor or the side of waist
slab with suitable arrangement as per approval of
Engineer-incharge, (for payment purpose only weight of
stainless steel members shall be considered excluding
fixing accessories such as nuts, bolts, fasteners etc.).

10.29 Providing & fixing fly proof wire gauze to windows,

clerestory windows & doors with M.S. Flat 15 x 3 mm
and nuts & bolts complete.
10.29.1 Galvanised M.S. Wire gauze with 0.63mm dia wire and 1.00 Sqm 844.70 One Square 845.00
1.4 mm aperture on both sides. Metre
10.29.2 Stainless steel (grade 304) wire gauze of 0.5 mm dia 1.00 Sqm 1133.55 One Square 1134.00
wire and 1.4 mm aperture on both sides. Metre
10.30 Providing & fixing glass panes with putty and glazing
clips in steel doors, windows, clerestory windows all
complete with :
10.30.1 4.0 mm thick glass panes. 1.00 Sqm 1064.65 One Square 1065.00
Metre
10.30.2 5.5 mm thick glass panes. 1.00 Sqm 1390.15 One Square 1390.00
Metre
10.31 Providing and fixing angle iron frames for doors, 1.00 Kg 130.50 One Kilogram 131.00
windows and ventilators of mild steel Angle sections of
size 35x35x5 mm, joints mitred and welded by angle
iron 35x35x5 mm or 35x 5 mm flat pieces to the existing
T-iron frame or to the wall with dash fastener, including
fixing of necessary butt hinges and screws and applying
a priming coat of approved steel primer, all complete as
per the direction of Engineer-In-charge.

Total of the Sub-Head - Steel Work : 56882.00

Sub-Head : Flooring
11.1 Brick on edge flooring with bricks of class designation
7.5 on a bed of 12 mm cement mortar, including filling
the joints with same mortar, with common burnt clay
non modular bricks:

11.1.1 1:4 (1 cement : 4 coarse sand) 1.00 Sqm 1006.95 One Square 1007.00
Metre
11.1.2 1:6 (1cement : 6 coarse sand) 1.00 Sqm 965.55 One Square 966.00
Metre

DSR - 2023 IN MS EXCEL Page 84 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.2 Dry brick on edge flooring in required pattern with 1.00 Sqm 792.05 One Square 792.00
bricks of class designation 7.5 on a bed of 12 mm mud Metre
mortar, including filling joints with sand, with common
burnt clay non modular bricks.

11.3 Cement concrete flooring 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate) finished with a floating
coat of neat cement, including cement slurry, but
excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate 1.00 Sqm 614.20 One Square 614.00
Metre
11.4 52 mm thick cement concrete flooring with concrete 1.00 Sqm 978.45 One Square 978.00
hardener topping, under layer 40 mm thick cement Metre
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) and top layer 12
mm thick cement hardener consisting of mix 1:2 (1
cement hardener mix : 2 graded stone aggregate 6 mm
nominal size) by volume, hardening compound mixed
@ 2 litre per 50 kg of cement or as per manufacturer's
specifications. This includes cost of cement slurry, but
excluding the cost of nosing of steps etc. complete.

11.5 62 mm thick cement concrete flooring with concrete 1.00 Sqm 1056.15 One Square 1056.00
hardener topping, under layer 50 mm thick cement Metre
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20mm nominal size) and top layer
12mm thick cement hardener consisting of mix 1:2 (1
cement hardener mix : 2 graded stone aggregate, 6mm
nominal size) by volume, hardening compound mixed
@ 2 litre per 50 kg of cement or as per manufacture’s
specifications. This includes cost of cement slurry, but
excluding the cost of nosing of steps etc. complete.

11.6 Cement plaster skirting up to 30 cm height, with

cement mortar 1:3 (1 cement : 3 coarse sand), finished
with a floating coat of neat cement.
11.6.1 18 mm thick. 1.00 Sqm 662.05 One Square 662.00
Metre
11.7 Cement concrete pavement with 1:2:4 (1 cement : 2 1.00 Cum 8595.15 One Cubic 8595.00
coarse sand : 4 graded stone aggregate 20 mm nominal Metre
size), including finishing complete.
11.8 Extra for making chequers of approved pattern on 1.00 Sqm 83.85 One Square 84.00
cement concrete floors, steps, landing, pavements etc. Metre

11.9 40 mm thick marble chips flooring rubbed and polished

to granolithic finish, under layer 34 mm thick cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 12.5 mm nominal size) and top layer
6mm thick with white, black, chocolate, grey, yellow or
green marble chips of sizes from 1 mm to 4 mm
nominal size, laid in cement marble powder mix 3:1 (3
cement : 1 marble powder) by weight in proportion of
4:7 (4 cement marble powder mix : 7 marble chips) by
volume, including cement slurry etc. complete :

11.9.1 Dark shade pigment with ordinary cement. 1.00 Sqm 1065.75 One Square 1066.00
Metre
11.9.2 Light shade pigment with white cement. 1.00 Sqm 1092.50 One Square 1093.00
Metre

DSR - 2023 IN MS EXCEL Page 85 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.9.3 Medium shade pigment with 50% white cement and 1.00 Sqm 1075.10 One Square 1075.00
50% ordinary cement. Metre
11.9.4 White cement without any pigment. 1.00 Sqm 1067.50 One Square 1068.00
Metre
11.9.5 Light shade pigment with ordinary cement. 1.00 Sqm 1061.70 One Square 1062.00
Metre
11.9.6 Ordinary cement without any pigment. 1.00 Sqm 1034.25 One Square 1034.00
Metre
11.10 40 mm thick marble chips flooring, rubbed and polished
to granolithic finish, under layer 31 mm thick cement
concrete 1:2:4 (1 cement : 2coarse sand : 4 graded
stone aggregate 12.5 mm nominal size) and top layer 9
mm thick with white, black, chocolate, grey, yellow or
green marble chips of sizes from 4 mm to 7 mm
nominal size, laid in cement marble powder mix 3:1 (3
cement : 1 marble powder) by weight in proportion of
4:7 (4 cement marble powder : 7 marble chips) by
volume, including cement slurry etc. complete.

11.10.1 Dark shade pigment with Ordinary cement. 1.00 Sqm 1072.10 One Square 1072.00
Metre
11.10.2 Light shade pigment with white cement. 1.00 Sqm 1110.30 One Square 1110.00
Metre
11.10.3 Medium shade pigment with 50% white cement and 1.00 Sqm 1085.45 One Square 1085.00
50% ordinary cement. Metre
11.10.4 White cement without any pigment. 1.00 Sqm 1071.05 One Square 1071.00
Metre
11.10.5 Light shade pigment with ordinary cement. 1.00 Sqm 1066.35 One Square 1066.00
Metre
11.10.6 Ordinary cement without any pigment. 1.00 Sqm 1027.10 One Square 1027.00
Metre
11.11 40 mm thick marble chips flooring, rubbed and polished
to granolithic finish, under layer 28 mm thick cement
concrete 1:2:4 (1 cement : 2coarse sand : 4 graded
stone aggregate 12.5 mm nominal size) and top layer 12
mm thick with white, black, chocolate, grey yellow or
green marble chips of sizes from 7 mm to 10 mm
nominal size, laid in cement marble powder mix 3:1 (3
cement : 1 marble powder) by weight in proportion of
2:3 (2 cement marble powder mix : 3 marble chips) by
volume, including cement slurry etc. complete :

11.11.1 Dark shade pigment with ordinary cement. 1.00 Sqm 1110.75 One Square 1111.00
Metre
11.11.2 Light shade pigment with white cement. 1.00 Sqm 1164.25 One Square 1164.00
Metre
11.11.3 Medium shade pigment with 50% white cement and 1.00 Sqm 1129.45 One Square 1129.00
50% ordinary cement. Metre
11.11.4 White cement without any pigment. 1.00 Sqm 1109.85 One Square 1110.00
Metre
11.11.5 Light shade pigment with ordinary cement. 1.00 Sqm 1102.70 One Square 1103.00
Metre
11.11.6 Ordinary cement without any pigment. 1.00 Sqm 1048.25 One Square 1048.00
Metre

DSR - 2023 IN MS EXCEL Page 86 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.12 Marble chips skirting up to 30 cm height, rubbed and
polished to granolithic finish, top layer 6 mm thick with
white, black, chocolate, grey, yellow or green marble
chips of sizes from smallest to 4 mm nominal size, laid
in cement marble powder mix 3:1 (3 cement : 1marble
powder) by weight in proportion of 4:7 (4 cement
marble powder mix : 7 marble chips) by volume :

11.12.1 18 mm thick with under layer 12 mm thick in cement

plaster 1:3 (1 cement : 3 coarse sand) :
11.12.1.1 Dark shade pigment with ordinary cement. 1.00 Sqm 1864.30 One Square 1864.00
Metre
11.12.1.2 Light shade pigment with white cement. 1.00 Sqm 1891.05 One Square 1891.00
Metre
11.12.1.3 Medium shade pigment with 50% white cement and 1.00 Sqm 1873.65 One Square 1874.00
50% ordinary cement. Metre
11.12.1.4 White cement without any pigment. 1.00 Sqm 1863.60 One Square 1864.00
Metre
11.12.1.5 Light shade pigment with ordinary cement. 1.00 Sqm 1860.25 One Square 1860.00
Metre
11.12.1.6 Ordinary cement without any pigment. 1.00 Sqm 1832.80 One Square 1833.00
Metre
11.13 Providing and fixing glass strips in joints of terrazzo/
cement concrete floors.
11.13.1 40 mm wide and 4 mm thick. 1.00 m 91.75 One Metre 92.00
11.14 Extra for laying terrazzo flooring on staircase treads not 1.00 Sqm 97.65 One Square 98.00
exceeding 30 cm in width including cost of forming, Metre
nosing etc.
11.15 Crazy marble stone flooring, including filling the gaps
with light shade pigment with white cement marble
powder mixture (3 parts of white cement : 1 part of
marble powder) by weight in proportion of 4:7
(4cement marble powder mix : 7 white, black or white
and black marble chips of sizes from 1 mm to 4 mm
nominal size by volume), with under layer 25 mm thick
cement concrete 1:2:4 (1 cement : 2 coarse sand :4
graded stone aggregate 12.5 mm nominal size),
including rubbing, polishing and cement slurry etc.
complete :

11.15.1 18 mm thick crazy marble stone white, black or as 1.00 Sqm 1714.80 One Square 1715.00
specified. Metre
11.16 Precast terrazzo tiles 22 mm thick with graded marble
chips of size upto12 mm, laid in floors, and landings,
jointed with neat cement slurry mixed with pigment to
match the shade of the tiles, including rubbing and
polishing complete, on 20 mm thick bed of cement
mortar 1:4 (1cement:4 coarse sand) :

11.16.1 Light shade pigment using white cement. 1.00 Sqm 1549.45 One Square 1549.00
Metre
11.16.2 Medium shade pigment using 50%white cement and 1.00 Sqm 1507.10 One Square 1507.00
50% ordinary cement. Metre
11.16.3 Dark shade pigment using ordinary cement. 1.00 Sqm 1450.00 One Square 1450.00
Metre
11.16.4 Ordinary cement without any pigment. 1.00 Sqm 1386.80 One Square 1387.00
Metre
11.17 Extra if terrazzo tiles are laid in treads of steps not 1.00 Sqm 124.05 One Square 124.00
exceeding 30 cm in width. Metre

DSR - 2023 IN MS EXCEL Page 87 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.18 Precast terrazzo tiles 22 mm thick with graded marble
chips of sizes upto 12 mm, in skirting and risers of steps
not exceeding 30 cm in height, on 12 mm thick cement
plaster 1:3 (1 cement : 3 coarse sand),jointed with neat
cement slurry mixed with pigment to match the shade
of the tiles, including rubbing and polishing complete
with tiles of :

11.18.1 Light shade pigment using white cement. 1.00 Sqm 2422.80 One Square 2423.00
Metre
11.18.2 Medium shade pigment using 50% white cement and 1.00 Sqm 2370.95 One Square 2371.00
50% ordinary cement. Metre
11.18.3 Dark shade pigment using ordinary cement. 1.00 Sqm 2308.75 One Square 2309.00
Metre
11.18.4 Ordinary cement without any pigment. 1.00 Sqm 2229.15 One Square 2229.00
Metre
11.19 Chequered terrazzo tiles 22 mm thick with graded
marble chips of size up to 6 mm in floors, jointed with
neat cement slurry mixed with pigment to match the
shade of the tiles, including rubbing and polishing
complete, on 20 mm thick bed of cement mortar 1:4 (1
cement :4 coarse sand) :

11.19.1 Light shade pigment using white cement. 1.00 Sqm 1533.80 One Square 1534.00
Metre
11.19.2 Medium shade pigment using 50% white cement, 50% 1.00 Sqm 1483.60 One Square 1484.00
ordinary cement. Metre
11.19.3 Dark shade pigment using ordinary cement. 1.00 Sqm 1442.15 One Square 1442.00
Metre
11.19.4 Ordinary cement without any pigment. 1.00 Sqm 1379.00 One Square 1379.00
Metre
11.20 Chequerred precast cement concrete tiles 22 mm thick
in footpath &courtyard, jointed with neat cement slurry
mixed with pigment to match the shade of tiles,
including rubbing and cleaning etc. complete, on 20mm
thick bed of cement mortar 1:4 (1 cement: 4 coarse
sand).

11.20.1 Light shade pigment using white cement. 1.00 Sqm 1402.00 One Square 1402.00
Metre
11.20.2 Medium shade pigment using 50% white cement 50% 1.00 Sqm 1328.35 One Square 1328.00
Grey cement. Metre
11.20.3 Dark shade pigment using ordinary cement. 1.00 Sqm 1119.50 One Square 1120.00
Metre
11.20.4 Ordinary cement without any pigment. 1.00 Sqm 1056.35 One Square 1056.00
Metre
11.21 Providing and fixing 10 mm thick acid and/or alkali
resistant tiles of approved make and colour using acid
and/or alkali resisting mortar bedding, and joints filled
with acid and/or alkali resisting cement as perish : 4457,
complete as per the direction of Engineer-in- Charge.

11.21.1 In flooring on a bed of 10 mm thick mortar 1:4 (1 acid

proof cement : 4 coarse sand).
11.21.1.1 Acid and alkali resistant tile. 1.00 Sqm 1738.15 One Square 1738.00
Metre
11.21.2 In dado/skirting on 12 mm thick mortar 1:4 (1 acid
proof cement : 4 coarse sand).
11.21.2.1 Acid and alkali resistant tile. 1.00 Sqm 1884.90 One Square 1885.00
Metre

DSR - 2023 IN MS EXCEL Page 88 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.22 Tile work in skirting, risers of steps and dado up to 2 m
height over 12 mm thick bed of cement mortar 1:3 (1
cement :3 coarse sand) and jointed with grey cement
slurry @ 3.3 kg/sqm including pointing in white cement
mixed with pigment of matching shade complete.

11.22.1 Marble tiles (polished) Raj Nagar.

11.22.1.1 8 mm thick. 1.00 Sqm 1475.35 One Square 1475.00
Metre
11.23 Marble stone flooring with 18mm thick marble stone as
per sample of marble shall be approved by Engineer-in-
charge over 20 mm (average) thick base of cement
mortar 1:4 (1 cement : 4 coarse sand) laid and jointed
with grey cement slurry including rubbing and polishing
complete with :

11.23.1 Makrana white second quality. 1.00 Sqm 3737.45 One Square 3737.00
Metre
11.23.2 Raj Nagar plain. 1.00 Sqm 2346.80 One Square 2347.00
Metre
11.23.3 Agaria White 1.00 Sqm 3164.80 One Square 3165.00
Metre
11.23.4 Black Zebra. 1.00 Sqm 3001.20 One Square 3001.00
Metre
11.23.5 Udaipur green marble 1.00 Sqm 2428.60 One Square 2429.00
Metre
11.23.6 Pink plain marble. 1.00 Sqm 2510.40 One Square 2510.00
Metre
11.24 Extra for pre finished nosing to treads of steps of 1.00 m 719.90 One Metre 720.00
marble stone.
11.25 Extra for marble stone flooring in treads of steps and 1.00 Sqm 851.80 One Square 852.00
risers using single length up to 2.00 metre . Metre
11.26 Kota stone slab flooring over 20 mm (average) thick
base laid over and jointed with grey cement slurry
mixed with pigment to match the shade of the slab
including rubbing and polishing complete with base of
cement mortar 1 : 4 (1 cement : 4 coarse sand) :

11.26.1 25 mm thick. 1.00 Sqm 1948.25 One Square 1948.00

Metre
11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, 1.00 Sqm 2354.70 One Square 2355.00
dado and pillars laid on 12 mm (average) thick cement Metre
mortar 1:3 (1 cement 3 coarse sand) and jointed with
grey cement slurry mixed with pigment to match the
shade of the slabs, including rubbing and polishing
complete.

11.28 40 mm thick fine dressed stone flooring over 20 mm

(average) thick base of cement mortar 1:5 ( 1cement : 5
coarse sand) with joints finished flush.
11.28.1 Red sand stone 1.00 Sqm 1280.10 One Square 1280.00
Metre
11.28.2 White sand stone 1.00 Sqm 1342.65 One Square 1343.00
Metre
11.29 40 mm thick fine dressed stone flooring over 20 mm
(average)thick base of cement mortar 1:5 (1 cement : 5
coarse sand) including pointing with cement mortar 1:2
(1 cement : 2 stone dust) with an admixture of pigment
to match the shade of stone.

11.29.1 Red sand stone 1.00 Sqm 1526.05 One Square 1526.00
Metre

DSR - 2023 IN MS EXCEL Page 89 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.29.2 White sand stone 1.00 Sqm 1588.65 One Square 1589.00
Metre
11.30 40 mm thick rubbed stone flooring over 20 mm
(average) thick base of cement mortar 1:5 (1 cement :5
coarse sand) with joints 3mm thick, side buttered with
cement mortar 1:2 (1 cement : 2 stone dust) admixed
with pigment to match the shade of stone and pointing
with same mortar

11.30.1 Red sand stone 1.00 Sqm 1647.00 One Square 1647.00
Metre
11.30.2 White sand stone 1.00 Sqm 1709.60 One Square 1710.00
Metre
11.31 Extra for pre finished nosing in treads of steps of Kota 1.00 m 191.40 One Metre 191.00
stone/ sand stone slab.
11.32 Extra for Kota stone/ sand stone in treads of steps and 1.00 Sqm 44.15 One Square 44.00
risers using single length above normal size up to 2.00 Metre
metre .
11.33 25mm wooden planking, tongued and grooved in
flooring including fixing with iron screws complete
with :
11.33.1 Second class teak wood 1.00 Sqm 4508.95 One Square 4509.00
Metre
11.33.2 Second class deodar wood 1.00 Sqm 3029.75 One Square 3030.00
Metre
11.34 38mm thick wood block flooring of first class teak wood 1.00 Sqm 12020.45 One Square 12020.00
laid over 25mm thick leveling layer of cement concrete Metre
1:2:4 (1 cement : 2 coarse sand: 4 graded stone
aggregate 10mm nominal size) to be paid separately
coated with a thin layer of hot bitumen penetration
80/25 (blown type)@ 2.45 kg per sqm. including fixing
blocks in position after dipping in hot bitumen (blown
type) up to half depth, planed, levelled smooth and
finished complete.

11.35 Providing and fixing M.S. angle 50x50x5 mm to act as 1.00 Kg 177.80 One Kilogram 178.00
nosing with lugs of M.S. flat 10x5 mm 10cm long forked
at end 60cm apart (minimum three lugs to be provided)
including necessary welding and applying a priming coat
of approved primer on exposed surface etc. complete.

11.37 Providing and laying Ceramic glazed floor tiles of size 1.00 Sqm 1096.55 One Square 1097.00
300x300 mm(thickness to be specified by the Metre
manufacturer) of 1st quality conforming to IS : 15622 of
approved make in colours such as White, Ivory, Grey,
Fume Red Brown, laid on 20 mm thick cement mortar
1:4 (1 Cement :4 Coarse sand), jointing with grey
cement slurry @ 3.3kg/sqm including pointing the joints
with white cement and matching pigment etc.,.,
complete.

11.37A Providing and fixing 1st quality ceramic glazed floor tiles 1.00 Sqm 1112.70 One Square 1113.00
conforming to IS : 15622 (thickness to be specified by Metre
the manufacturer ) of approved make in all colours,
shades except burgundy, bottle green, black of any size
as approved by Engineer-in-Charge in skirting, risers of
steps and dados over 12 mm thick bed of cement
Mortar 1:3 (1cement: 3 coarse sand) and jointing with
grey cement slurry @ 3.3kgper sqm including pointing
the joints with white cement mixed with pigment of
matching shade complete.

DSR - 2023 IN MS EXCEL Page 90 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.38 Providing and laying Ceramic glazed floor tiles of size 1.00 Sqm 1315.30 One Square 1315.00
300x300 mm(thickness to be specified by the Metre
manufacturer), of 1st quality conforming to IS : 15622,
of approved make, in all colours, shades, except White,
Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed
of cement mortar1:4 (1 Cement : 4 Coarse sand),
jointing with grey cement slurry @3.3kg/sqm including
pointing the joints with white cement and matching
pigments etc., complete.

11.39 Providing and laying rectified Glazed Ceramic floor tiles 1.00 Sqm 1330.00 One Square 1330.00
of size 300x300mm or more (thickness to be specified Metre
by the manufacturer), of 1stquality conforming to IS :
15622, of approved make, in colours White, Ivory, Grey,
Fume Red Brown, laid on 20 mm thick cement mortar
1:4(1 Cement: 4 Coarse sand), jointing with grey cement
slurry @ 3.3kg/sqm including grouting the joints with
white cement and matching pigments etc., complete.

11.40 Providing and laying rectified Glazed Ceramic floor tiles 1.00 Sqm 1439.40 One Square 1439.00
of size 300x300 mm or more (thickness to be specified Metre
by the manufacturer), of 1st quality conforming to IS :
15622, of approved make, in all colours, shades, except
White, Ivory, Grey, Fume Red Brown, laid on 20 mm
thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand),
jointing with grey cement slurry @ 3.3kg/sqm including
pointing the joints with white cement and matching
pigments etc., complete.

11.41 Providing and laying vitrified floor tiles in different sizes

(thickness to be specified by the manufacturer) with
water absorption less than 0.08%and conforming to IS :
15622 , of approved make, in all colours and shades,
laid on 20mm thick cement mortar 1:4 (1 cement : 4
coarse sand) jointing with grey cement slurry @
3.3kg/sqm including grouting the joints with white
cement and matching pigments etc., complete.

11.41.1 Size of Tile 500x500 mm 1.00 Sqm 1524.30 One Square 1524.00
Metre
11.41.2 Size of Tile 600x600 mm 1.00 Sqm 1553.45 One Square 1553.00
Metre
11.41.3 Size of Tile 800x800 mm 1.00 Sqm 1885.50 One Square 1886.00
Metre
11.41.4 Size of Tile 1000x1000 mm 1.00 Sqm 2089.65 One Square 2090.00
Metre
11.41A Providing and laying Vitrified tiles in floor in different
sizes (thickness to be specified by the manufacturer)
with water absorption less than 0.08% and conforming
to IS:15622, of approved brand & manufacturer, in all
colours and shade, laid on 20 mm thick cement mortar
1:4 (1 cement: 4 coarse sand) jointing with grey cement
slurry @3.3 kg/sqm including grouting the joints with
white cement and matching pigments etc. The tiles
must be cut with the zero chipping diamond cutter
only . Laying of tiles will be done with the notch trowel,
plier, wedge, clips of required thickness, leveling system
and rubber mallet for placing the tiles gently and easily.

11.41A.1 Double charge vitrified tile polished finish of size

DSR - 2023 IN MS EXCEL Page 91 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.41A.1.1Size of Tile 600 x 600 mm 1.00 Sqm 1453.65 One Square 1454.00
Metre
11.41A.1.2Size of Tile 800 x 800 mm 1.00 Sqm 1534.85 One Square 1535.00
Metre
11.41A.1.3Size of Tile 600 x 1200 mm 1.00 Sqm 1577.15 One Square 1577.00
Metre
11.41A.1.4Size of Tile 800 x 1200 mm 1.00 Sqm 1870.25 One Square 1870.00
Metre
11.41A.1.5Size of Tile 1000 x 1000 mm 1.00 Sqm 1801.70 One Square 1802.00
Metre
11.41A.2 Glazed vitrified floor tiles polished finish of size
11.41A.2.1Size of Tile 600 x 600 mm 1.00 Sqm 1502.75 One Square 1503.00
Metre
11.41A.2.2Size of Tile 600 x 1200 mm 1.00 Sqm 1798.80 One Square 1799.00
Metre
11.41A.2.3Size of Tile 800 x 800 mm 1.00 Sqm 1728.80 One Square 1729.00
Metre
11.41A.2.4Size of Tile 800 x 1200 mm 1.00 Sqm 2056.90 One Square 2057.00
Metre
11.41A.2.5Size of Tile 1200 x 1200 mm 1.00 Sqm 2541.00 One Square 2541.00
Metre
11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size
11.41A.3.1Size of Tile 600 x 600 mm 1.00 Sqm 1464.85 One Square 1465.00
Metre
11.41A.3.2Size of Tile 600 x 1200 mm 1.00 Sqm 1797.30 One Square 1797.00
Metre
11.41A.3.3Size of Tile 800 x 800 mm 1.00 Sqm 1724.40 One Square 1724.00
Metre
11.41A.3.4Size of Tile 800 x 1200 mm 1.00 Sqm 2056.90 One Square 2057.00
Metre
11.41A.3.5Size of Tile 1200 x 1200 mm 1.00 Sqm 2838.50 One Square 2839.00
Metre
11.42 Deduct for not using 20 mm thick cement mortar 1:4 (1 1.00 Sqm -850.10 One Square -850.00
cement : 4coarse sand) bedding in laying of floor tiles Metre
and jointing with grey cement slurry @ 3.3kg/sqm

11.43 Fixing glazed/ Ceramic/ Vitrified floor tiles with cement 1.00 Sqm 753.25 One Square 753.00
based high polymer modified quick-set tile adhesive Metre
(Water based) conforming to IS: 15477, in average 3mm
thickness.

11.44 Crazy ceramic tile flooring, with under layer 12 mm 1.00 Sqm 954.15 One Square 954.00
thick cement mortar 1:4 (1 cement: 4 coarse sand), with Metre
joints not exceeding 5 mm, including filling the gaps
with ordinary cement mixture & mixing with synthetic
polyester fibre, triangular in shape having specific
gravity of1.34 to 1.40, cross section size ranging from
10 to 40 micron & length upto 6 mm , mixing fibre @
125 grams per 50 kg of cement in cement mortar,
including providing and mixing water proofing material
in mortar@ 1 kg per 50 kg of cement , all complete as
per direction of Engineer-in-charge.

11.45 Providing and laying 500x500x40mm thick Turf paver 1.00 Sqm 1708.10 One Square 1708.00
(Turf pave XD) on 150mm thick sub grade of compacted Metre
bed of 20mm thick nominal size stone aggregate and
base course and filling with 150mm thick jamuna sand
including spreading, well ramming, consolidating and
finishing smooth etc. all complete as per direction of
Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 92 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.46 Providing and laying Vitrified tiles in different sizes
(thickness to be specified by manufacturer) with water
absorption less than 0.08 % and conforming to I.S.
15622, of approved make in all colours & shade in
skirting, riser of steps, over 12 mm thick bed of cement
mortar 1:3 (1cement: 3 coarse sand), jointing with grey
cement slurry @ 3.3kg/sqm including grouting the joint
with white cement & matching pigments etc. complete.

11.46.1 Size of Tile 500x500 mm 1.00 Sqm 1593.90 One Square 1594.00
Metre
11.46.2 Size of Tile 600x600 mm 1.00 Sqm 1623.05 One Square 1623.00
Metre
11.46.3 Size of Tile 800x800 mm 1.00 Sqm 1958.45 One Square 1958.00
Metre
11.46.4 Size of Tile 1000x1000 mm 1.00 Sqm 2162.60 One Square 2163.00
Metre
11.46A Providing and fixing glazed screen printed border tile 1.00 m 216.20 One Metre 216.00
75mm wide having thickness 5mm, of approved quality
& make, in all shades, design and prints, in dado, over
12mm thick bed of cement mortar1:3 (1 Cement : 3
Coarse sand) and jointing with grey cement slurry @ 3.3
kg/sqm including pointing with white cement mixed
with pigment of matching shade, all complete as
approved by Engineer - in - Charge.

11.47 Providing and laying Vitrified tiles in different sizes

(thickness to be specified by the manufacturer), with
water absorption less than 0.08%and conforming to IS:
15622, of approved brand & manufacturer in all colours
and shade in skirting, riser of steps, laid with cement
based high polymer modified quick set tile adhesive
(water based) conforming to IS: 15477, in average 6 mm
thickness, including grouting of joints(Payment for
grouting of joints to be made separately).

11.47.1 Size of Tile 500x500 mm 1.00 Sqm 1864.75 One Square 1865.00
Metre
11.47.2 Size of Tile 600x600 mm 1.00 Sqm 1893.90 One Square 1894.00
Metre
11.47.3 Size of Tile 800x800 mm 1.00 Sqm 2229.25 One Square 2229.00
Metre
11.47.4 Size of Tile 1000x1000 mm 1.00 Sqm 2433.40 One Square 2433.00
Metre
11.48 Grouting the joints of flooring tiles having joints of 3
mm width, using epoxy grout mix of 0.70 kg of organic
coated filler of desired shade(0.10 kg of hardener and
0.20 kg of resin per kg), including filling/grouting and
finishing complete as per direction of Engineer-in-
charge.

11.48.1 Size of Tile 500x500 mm 1.00 Sqm 373.35 One Square 373.00
Metre
11.48.2 Size of Tile 600x600 mm 1.00 Sqm 309.05 One Square 309.00
Metre
11.48.3 Size of Tile 800x800 mm 1.00 Sqm 244.75 One Square 245.00
Metre
11.48.4 Size of Tile 1000x1000 mm 1.00 Sqm 174.50 One Square 175.00
Metre

DSR - 2023 IN MS EXCEL Page 93 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.49 Providing and laying Vitrified tiles in floor with different
sizes (thickness to be specified by the manufacturer),
with water absorption less than 0.08% and conforming
to IS:15622, of approved brand & manufacturer, in all
colours and shade, laid with cement based high
polymer modified quick set tile adhesive (water based)
conforming to IS : 15477, in average 6 mm thickness,
including grouting of joints (Payment for grouting of
joints to be made separately).

11.49.1 Size of Tile 500x500 mm 1.00 Sqm 1696.20 One Square 1696.00
Metre
11.49.2 Size of Tile 600x600 mm 1.00 Sqm 1725.35 One Square 1725.00
Metre
11.49.3 Size of Tile 800x800 mm 1.00 Sqm 2060.75 One Square 2061.00
Metre
11.49.4 Size of Tile 1000x1000 mm 1.00 Sqm 2264.90 One Square 2265.00
Metre
11.49A Providing and laying full body vitrified tile in floor of
minimum thickness 15 mm with water absorption less
than 0.06% and conforming to IS: 15622, of approved
make, brand and manufacturer, laid on 20 mm thick
base cement mortar 1:4 (1 cement: 4 coarse sand)
jointing with grey cement slurry @3.30 kg / sqm
including grouting the joints with white cement and
matching pigments etc. The slab must be cut with the
zero chipping diamond cutter only. Laying of slab will be
done with the help of notch trowel, wedge, clips of
required thickness, vacuum cups for lifting, leveling
system and rubber mallet for placing the slab gently
and easily.

Size of tile 800x2400mm of all colours and shades 1.00 Sqm 3623.95 One Square 3624.00
Metre
11.50 Deduct for not grouting the joints with white cement 1.00 Sqm -13.30 One Square -13.00
and matching pigment in the items of fixing of vitrified Metre
tiles
11.51 Providing and laying machine cut, mirror polished,
Italian Marble stone flooring laid in required pattern in
linear portion of the building all complete as per
architectural drawings, with 18 mm thick stone slab laid
over 20mm (average) thick base of cement mortar 1:4
(1 cement : 4 coarse sand) laid and jointed with white
cement slurry @ 4.4 kg/sqm, including pointing with
white cement slurry admixed with pigment to match
the marble shade including rubbing, curing and
polishing etc. all complete as specified and as directed
by the Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso 1.00 Sqm 6603.35 One Square 6603.00
verona, Fire Red or Dark Emperadore etc Metre

DSR - 2023 IN MS EXCEL Page 94 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.52 Providing and laying machine cut, mirror polished
Marble stone flooring, in required design (Simple
geometrical, abstract etc.) and in patterns in
combination with Italian marble stones of different
colours, shades and finished surface texture etc., in
linear portions of the building, all complete as per the
architectural drawings, with 18 mm thick stone slab laid
over 20 mm (average) thick base of cement mortar 1:4
(1 cement : 4 coarse sand) laid and jointed with white
cement slurry @ 4.4 kg/sqm including pointing with
white cement slurry admixed with pigment to match
the marble shade including rubbing, curing and
polishing etc. all complete as specified and as directed
by the Engineer-in-Charge.

11.52.1 18 mm thick Italian Marble stone slab, Perlato, Rosso 1.00 Sqm 6927.35 One Square 6927.00
verona, Fire Red or Dark Emperadore etc. Metre
11.53 Providing and fixing Glass mossaic tiles on finished plain 1.00 Sqm 3891.15 One Square 3891.00
wall surface of size 20 mm x 20 mm x 4 mm in all Metre
colour, design , fixing in customized design as per
direction of Engineer in charge. The glass mosaic tiles
shall be fixed on the wall surface with the help of
approved adhesive applied at the rate of 2.5 kg per sqm
and grouting of the same. The rate is inclusive of all
operations, material and required pattern approved by
Engineer-in-charge.

11.54 Providing and fixing removable raised/false access

flooring with system and its components of approved
make for different plenum height with possible height
adjustment upto 50 mm, comprising of modular load
bearing floor panels supported on G.I. rectangular
stinger frame work and G.I. Pedestal etc. all complete,
as per the architectural drawings, as specified and as
directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular

framework, pedestals made out of GI tube of thickness
minimum 2 mm and 25 mm outer diameter, fully
welded on to the G.I. Base plate of size 100mm x
100mm x 3mm at the bottom of the pedestal tube, G.I.
pedestal head of size 75mmx75mmx3.5 mm welded
with GI fully threaded stud 16mm outer diameter with
two GI Check nuts screwed on the stud for level
adjustment upto 50mm, locking and stabilizing the
pedestal head in position at the required level. The
pedestals shall be fixed to the subfloor (base) through
base plate using epoxy based adhesive of approved
make or the machine screw with rawl plug.

DSR - 2023 IN MS EXCEL Page 95 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
(b) Stringers system in all steel construction hot dipped
galvanized of rectangular size 570x20x30x0.80mm thick
having holes at both ends for securing the stringers on
to the pedestal head using fully threaded screws
ensuring maximum lateral stability in all directions, the
grid formed by the pedestal and stringer assembly shall
receive the floor panel, this system shall provide
adequate solid, rigid support for access floor panel, the
system shall provide a minimum clear uninterrupted
clearance between the bottom of the floor for electrical
conduits and wiring etc. all complete as per the
architectural drawings, as specified and as directed by
the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of

600x600x32 mm medium grade Filled Steel anti static
high pressure Lamination of 800H grade (FS800H).
Access Floor panel shall be steel welded construction
with an enclosed bottom pan with uniform pattern of
64 hemispherical cones. The top and bottom plates of
Steel Gauges: top 0.6 mm and bottom 0.7 mm fused
spot welded together (minimum 64 welds in each dome
and 20 welds along each flange).

The panel should be Corroresist epoxy coated for

lifetime rust protection and cavity formed by the top
and bottom plate is filled with Pyrogrip noncombustible
Portland cementitious core mixed with lightweight
foaming compound. The access floor shall be factory
finished with Anti-static High Pressure laminate with
Non Warp technology upto 1mm thickness for superior
adhesion and Surface flatness within 0.75mm.The panel
is to withstand a Concentrated Load of 363 kgs applied
on area 25mm x 25mm without collapse in the centre
of the panel which is placed on four steel blocks. The
panel will withstand and Uniformly Distributed Load
(UDL) minimum 1250 kg/sqm and an impact load of
50kg all complete as per the approved manufacturers
specification and as per the direction of Engineer-in-
charge. All specification must be printed on the side of
the panel to ensure the quality of the product.

11.54.1 300 mm Finished Floor Height (FFH) 1.00 Sqm 5623.95 One Square 5624.00
Metre
11.54.2 450 mm Finished Floor Height (FFH). 1.00 Sqm 5977.35 One Square 5977.00
Metre
11.55 Providing and laying flamed finish Granite stone flooring
in required design and patterns, in linear as well as
curvilinear portions of the building all complete as per
the architectural drawings with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4
(1 cement : 4 coarse sand) laid and jointed with cement
slurry and pointing with white cement slurry admixed
with pigment of matching shade including rubbing,
curing and polishing etc. all complete as specified and
as directed by the Engineer-in-Charge :

11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, 1.00 Sqm 3186.70 One Square 3187.00
Elite Brown, Cat Eye or equivalent. Metre

DSR - 2023 IN MS EXCEL Page 96 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
11.56 Providing and laying Polished Granite stone flooring in
required design and patterns, in linear as well as
curvilinear portions of the building all complete as per
the architectural drawings with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4
(1 cement : 4 coarse sand) laid and jointed with cement
slurry and pointing with white cement slurry admixed
with pigment of matching shade including rubbing ,
curing and polishing etc. all complete as specified and
as directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab jet Black, Cherry Red, Elite 1.00 Sqm 4481.30 One Square 4481.00
Brown, Cat Eye or equivalent Metre
11.56.2 Polished Granite stone slab of all colour and texture 1.00 Sqm 3071.05 One Square 3071.00
except Black, Cherry/Ruby Red Metre
Total of the Sub-Head - Flooring : 242519.00
Sub-Head : Roofing
12.1 Providing corrugated G.S. sheet roofing including
vertical / curved surface fixed with polymer coated J or
L hooks, bolts and nuts 8 mm diameter with bitumen
and G.I. limpet washers or with G.I. limpet washers
filled with white lead, including a coat of approved steel
primer and two coats of approved paint on overlapping
of sheets complete (up to any pitch in horizontal/
vertical or curved surfaces), excluding the cost of
purlins, rafters and trusses and including cutting to size
and shape wherever required.

12.1.1 1.00 mm thick with zinc coating not less than 275 1.00 Sqm 1457.15 One Square 1457.00
gm/m* Metre
12.1.2 0.80 mm thick with zinc coating not less than 275 1.00 Sqm 1257.55 One Square 1258.00
gm/m* Metre
12.1.3 0.63 mm thick with zinc coating not less than 275 gm/ 1.00 Sqm 1087.65 One Square 1088.00
m* Metre
12.2 Extra for straight cutting in C.G.S. sheet roofing for
making opening of area exceeding 40 sq. decimeter for
chimney stacks, sky light etc.:
12.2.1 1.00 mm thick 1.00 m 116.15 One Running 116.00
Metre
12.2.2 0.80 mm thick 1.00 m 92.95 One Running 93.00
Metre
12.2.3 0.63 mm thick 1.00 m 92.95 One Running 93.00
Metre
12.3 Extra for circular cutting in C.G.S. sheet roofing for
making opening of area exceeding 40 sq. decimeter:
12.3.1 1.00 mm thick 1.00 m 671.45 One Running 671.00
Metre
12.3.2 0.80 mm thick 1.00 m 536.30 One Running 536.00
Metre
12.3.3 0.63 mm thick 1.00 m 536.30 One Running 536.00
Metre
12.4 Providing ridges or hips of width 60 cm overall width
plain G.S. sheet fixed with polymer coated J or L hooks,
bolts and nuts 8 mm dia G.I. limpet and bitumen
washers complete.

12.4.1 0.80 mm thick with zinc coating not less than 275 1.00 m 1083.30 One Running 1083.00
gm/m* Metre
12.4.2 0.63 mm thick with zinc coating not less than 275 1.00 m 980.50 One Running 981.00
gm/m* Metre

DSR - 2023 IN MS EXCEL Page 97 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.5 Providing valleys of 90 cm wide overall in plain G.S.
sheet fixed with polymer coated J or L hooks, bolts and
nuts 8 mm dia G.I. limpet and bitumen washers
complete :

12.5.1 1.60 mm thick with zinc coating not less than 350 1.00 m 1863.90 One Running 1864.00
gm/m* Metre
12.6 Providing and fixing of 40 cm overall width plain G.S.
sheet fixed with polymer coated J or L hooks, bolts and
nuts, G.I. limpet and bitumen washer complete, bent to
shape and fixed in wall with cement mortar 1:3 (1
cement : 3 coarse sand).

12.6.1 1.00 mm thick with zinc coating not less than 275 1.00 m 857.55 One Running 858.00
gm/m* Metre
12.7 Providing and fixing 15 cm wide, 45 cm overall semi-
circular plain G.S. sheet gutter with iron brackets 40x3
mm size, bolts, nuts and washers etc., including making
necessary connections with rain water pipes complete.

12.7.1 0.80 mm thick with zinc coating not less than 275 1.00 m 1029.65 One Running 1030.00
gm/m* Metre
12.7.2 0.63 mm thick with zinc coating not less than 275 1.00 m 944.05 One Running 944.00
gm/m* Metre
12.8 Providing reinforced by organic fibres and/or inorganic 1.00 Sqm 536.40 One Square 536.00
synthetic fibres cement 6 mm thick corrugated sheets Metre
(as per IS: 14871) roofing up to any pitch and fixing with
polymer coated J or L hooks, bolts and nuts 8 mm dia.
G.I. plain and bitumen washers or with self drilling
fastener and EPDM washers etc. complete (excluding
the cost of purlins, rafters and trusses), including cutting
sheets to size and shape wherever required.

12.9 Extra for straight cutting in reinforced by organic fibres 1.00 m 92.95 One Running 93.00
and/or inorganic synthetic fibres cement corrugated, Metre
semi corrugated 6 mm thick sheet roofing for making
openings of area exceeding 40 square decimeter
forchimney stacks, skylights etc.

12.10 Extra for circular cutting in reinforced by organic fibres 1.00 m 256.70 One Running 257.00
and/or inorganic synthetic fibres cement corrugated/ Metre
semi corrugated 6 mm thick sheet roofing for making
openings of area exceeding 40 square decimeter.

12.11 Extra for providing and fixing wind ties of 40x 6 mm flat 1.00 m 195.60 One Running 196.00
iron section. Metre
12.12 Providing and fixing ridges and hips in fibre cement
reinforced by organic fibres and/or inorganic synthetic
fibres roofing with suitable fixing accessories or self
drilling fastener and EPDM washer etc. complete.

12.12.1 Corrugated serrated adjustable ridges 1.00 m 522.95 One Metre 523.00
12.12.2 Plain wing adjustable ridges 1.00 m 522.95 One Metre 523.00
12.12.3 Close fitting adjustable ridges 1.00 m 585.70 One Metre 586.00
12.12.4 Unserrated adjustable hips 1.00 m 521.85 One Metre 522.00
12.13 Providing and fixing fibre cement reinforced by organic
fibres and/or inorganic synthetic fibres roofing
accessories in all colours with polymer coated J or L
hooks, bolts and nuts and or G.I. seam bolts and nuts,
G.I.plain and bitumen washers or with self drilling
fastener and EPDM washer etc. complete:

DSR - 2023 IN MS EXCEL Page 98 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.13.1 Corrugated apron pieces 1.00 m 428.50 One Running 429.00
Metre
12.13.2 Eave's filler pieces 1.00 m 345.05 One Running 345.00
Metre
12.13.3 North light curves 1.00 m 567.20 One Running 567.00
Metre
12.13.4 Ventilator curves 1.00 m 627.30 One Running 627.00
Metre
12.13.5 Barge boards 1.00 m 724.65 One Running 725.00
Metre
12.13.6 Ridge finials 1.00 pairs 303.70 Each Pair 304.00
12.13.7 Special north light curves 1.00 No. 1013.85 Each 1014.00
12.13.8 S type louvers 1.00 m 560.05 One Running 560.00
Metre
12.14 Providing flat iron brackets 50x3 mm size with 1.00 m 92.40 One Running 92.00
necessary bolts, nuts and washers etc. for fixing G.S. Metre
sheets gutters with purlins.
12.15 Painting top of roofs with bitumen of approved quality
@ 17kg per 10 sqm impregnated with a coat of coarse
sand at 60 cudm per 10 sqm, including cleaning the slab
surface with brushes and finally with a piece of cloth
lightly soaked in kerosene oil complete :

12.15.1 With residual type petroleum bitumen of grade VG -10 1.00 Sqm 166.20 One Square 166.00
Metre
12.16 10 cm thick (average) mud phaska of damped brick
earth on roofs laid to slope consolidated and plastered
with 25 mm thick mud mortar mixed with bhusa @ 35
kg per cum of earth and gobri leaping with mix 1:1 (1
clay : 1 cow dung) and covered with flat tile bricks,
grouted with cement mortar 1:3 (1 cement : 3 fine
sand) mixed with 2% of integral water proofing
compound by weight of cement and finished neat:

12.16.1 With common burnt clay F.P.S.(non modular) brick tile 1.00 Sqm 1050.20 One Square 1050.00
of class designation 10 Metre
12.17 10 cm thick (average) mud phaska of damped brick
earth on roofs laid to slope consolidated and plastered
with 25 mm thick mud mortar with bhusha @ 35 kg per
cum of earth and gobri leaping with mix 1:1 (1 clay : 1
cow-dung) and covered with machine moulded tile
bricks, grouted with cement mortar 1:3 (1 cement : 3
fine sand) mixed with 2% of integralwater proofing
compound by weight of cement and finished neat.

12.17.1 With machine moulded common burnt clay F.P.S. (non 1.00 Sqm 1074.50 One Square 1075.00
modular) brick tiles of class designation 12.5, Metre
conforming to IS 2690
12.18 Extra for every additional 1 cm thickness of mud 1.00 Sqm 24.20 One Square 24.00
phaska. Metre
12.19 Providing and laying brick tiles over mumty roofs,
grouted with cement mortar 1:3 (1 cement : 3 fine
sand) mixed with 2% of integral water proofing
compound by weight of cement, over 12 mm layer of
cement mortar 1:3 (1 cement : 3 fine sand) and finished
neat:

12.19.1 With common burnt clay F.P.S. (non modular) brick tiles 1.00 Sqm 607.40 One Square 607.00
of class designation 10 Metre

DSR - 2023 IN MS EXCEL Page 99 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.20 Providing and laying pressed clay tiles (as per approved 1.00 Sqm 709.75 One Square 710.00
pattern 20 mm nominal thickness of approved size) on Metre
roofs jointed with cement mortar 1:4 (1 cement : 4
coarse sand) mixed with 2% integral water proofing
compound, laid over a bed of 20 mm thick cement
mortar 1:4 (1 cement : 4 coarse sand) and finished neat
complete.

12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 stone aggregate 10 mm and
down gauge), including finishing with cement mortar
1:3 (1 cement : 3 fine sand) as per standard design :

12.21.1 In 75x75 mm deep chase 1.00 m 305.15 One Running 305.00

Metre
12.22 Making khurras 45x45 cm with average minimum 1.00 No. 298.25 Each 298.00
thickness of5 cm cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate of 20 mm
nominal size) over P.V.C. sheet 1 m x1 m x 400 micron,
finished with 12 mm cement plaster 1:3 (1 cement : 3
coarse sand) and a coat of neat cement, rounding the
edges and making and finishing the outlet complete.

12.23 Providing sand stone slab for roofing and laying them in
cement mortar 1 : 4 (1 cement : 4 coarse sand) over
wooden karries or R.C.C. battens or structural steel
sections (Karries or battens or structural steel sections
to be paid separately), including pointing the ceiling
joints with cement mortar 1:3 (1 cement : 3 fine sand )
complete :

12.23.1 Red sand stone slab

12.23.1.1 40 to 50 mm thick 1.00 Sqm 1138.20 One Square 1138.00
Metre
12.23.2 White sand stone slab :
12.23.2.1 40 to 50 mm thick 1.00 Sqm 1106.90 One Square 1107.00
Metre
12.24 Providing and fixing insulating board ceiling of approved
quality with necessary nails etc. complete (frame work
to be paid separately) :
12.24.1 Natural colour insulating board
12.24.1.1 12 mm thick 1.00 Sqm 924.35 One Square 924.00
Metre
12.24.2 White face insulating board
12.24.2.1 12 mm thick 1.00 Sqm 966.60 One Square 967.00
Metre
12.24.3 Flame retardant face insulating board
12.24.3.1 12 mm thick 1.00 Sqm 1121.55 One Square 1122.00
Metre
12.25 Providing and fixing flat pressed 3 layer medium density
particle board or graded particle board (Grade I) IS:
3087 marked, in ceiling with necessary nails etc.
complete (frame work to be paid separately):

12.25.1 12 mm thick 1.00 Sqm 1070.60 One Square 1071.00

Metre
12.26 Providing and fixing plain multipurpose cement
board(Hight pressure steam cured) with suitable screws
for cement particle board in ceiling etc. complete
(frame work to be paid seperatately).

DSR - 2023 IN MS EXCEL Page 100 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.26.1 6 mm thick Cement fiber board, Type-B, Category-III as 1.00 Sqm 921.95 One Square 922.00
per IS: 14862 : 2000 Metre
12.26.2 6 mm thick Cement bonded wood particle board as per 1.00 Sqm 890.65 One Square 891.00
IS:14276 Metre
12.27 Extra for Circular cutting including wastages in ceiling
with:
12.27.1 2nd class teak wood planks 20 mm thick 1.00 m 726.30 One Running 726.00
Metre
12.27.2 Natural colour insulating board
12.27.2.1 12 mm thick 1.00 m 487.00 One Running 487.00
Metre
12.27.3 White face insulating board:
12.27.3.1 12 mm thick 1.00 m 492.25 One Running 492.00
Metre
12.27.4 Flame retardant face insulating board:
12.27.4.1 12 mm thick 1.00 m 511.50 One Running 512.00
Metre
12.27.5 Standard quality hard board sheet:
12.27.5.1 3 mm thick 1.00 m 470.10 One Running 470.00
Metre
12.27.5.2 4.5 mm thick 1.00 m 485.70 One Running 486.00
Metre
12.28 Extra for providing and fixing ceiling to curved surfaces 1.00 Sqm 453.10 One Square 453.00
in narrow widths Metre
12.31 Providing 10 mm thick plaster of Paris (gypsum
anhydrous) ceiling up to a height of 5 m above floor
level, over first class kail wood strips 25x6 mm with 10
mm gap in between and reinforced with rabbit wire
mesh fixed to wooden frame (frame work to be paid
separately):

12.31.1 Flat surfaces 1.00 Sqm 1718.95 One Square 1719.00

Metre
12.31.2 Curved surfaces 1.00 Sqm 2067.45 One Square 2067.00
Metre
12.32 Extra for sunk or raised mouldings in the plaster of Paris 1.00 Sqm 607.45 One Square 607.00
(Gypsum anhydrous) ceiling. Metre
12.33 Extra for providing plaster of Paris (Gypsum anhydrous) 1.00 units 265.70 sqm per 266.00
ceiling above 5 metres height from floor level. metre height

12.34 Providing fixing thermal insulation of ceiling (under 1.00 Sqm 703.05 One Square 703.00
deck insulation) with Resin Bonded Fibre glass wool Metre
conforming to IS : 8183, density 24kg / m3, 50 mm
thick, wrapped in 200 G Virgin Polythene bags, fixed to
ceiling with metallic cleats (50x50x3 mm) @ 60 cm and
wire mesh of 12.5 mm x 24 gauge wire mesh, for top
most ceiling of building.

12.35 Providing and fixing thermal insulation with Resin 1.00 Sqm 297.25 One Square 297.00
Bonded Fibre glass wool conforming to IS: 8183. Density Metre
16 kg/m°, 50 mm thick, wrapped in 200G Virgin
Polythene bags placed over existing false ceiling and
held in position by criss-crossing GI wire.

12.36 Thermal Insulation of roofing with Expanded

polystyrene fixed with suitable adhesive to the false
ceiling as per the directions of the Engineer- in-charge:

12.36.1 With Type N - Normal 50 mm thick 1.00 Sqm 321.75 One Square 322.00
Metre
12.36.2 With Type SE - Self Extinguishing type 50 mm thick 1.00 Sqm 353.05 One Square 353.00
Metre

DSR - 2023 IN MS EXCEL Page 101 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.37 Providing and fixing 100 mm diameter and 60 cm long
rain water spout in cement mortar 1:4 (1 cement : 4
fine sand).
12.37.1 Stone ware spout 1.00 Nos 164.20 One Each 164.00
12.38 Providing and fixing M.S. holder bat clamps of approved
design to C.I. or S.C.I. rain water pipes embedded in and
including cement concrete blocks 10x10x10 cm of 1:2:4
mix (1 cement : 2 coarse sand : 4 gradedstone
aggregate 20 mm nominal size) and cost of cutting
holes and making good the walls etc. :

12.38.1 100 mm diameter 1.00 Nos 362.85 One Each 363.00

12.38.2 150 mm diameter 1.00 Nos 395.60 One Each 396.00
12.39 Providing lead caulked joints to sand cast iron rain
water pipes and fittings:
12.39.1 100 mm dia. Pipe 1.00 Nos 580.50 One Each 581.00
12.39.2 150 mm dia. Pipe 1.00 Nos 798.00 One Each 798.00
12.40 Providing, fixing and embedding sand cast iron
accessories for rain water pipes in the masonry
surrounded with 12 mm thick cement mortar of the
same mix, as that of masonry (lead caulking will be paid
for separately):

12.40.1 Sand cast iron plain shoes :

12.40.1.1 150 mm diameter 1.00 Nos 511.90 One Each 512.00
12.41 Providing and fixing on wall face unplasticised Rigid PVC
rain water pipes conforming to IS : 13592 Type A,
including jointing with seal ring conforming to IS : 5382,
leaving 10 mm gap for thermal expansion, (i) Single
socketed pipes.

(i)Single socketed pipes.

12.41.1 75 mm diameter 1.00 m 248.80 One Running 249.00
Metre
12.41.2 110 mm diameter 1.00 m 377.40 One Running 377.00
Metre
12.42 Providing and fixing on wall face unplasticised - PVC
moulded fittings/accessories for unplasticised Rigid PVC
rain water pipes conforming to IS 13592 Type A,
including jointing with seal ring conforming to IS : 5382,
leaving 10 mm gap for thermal expansion.

12.42.1 Coupler
12.42.1.1 75mm 1.00 Nos 91.70 One Each 92.00
12.42.1.2 110mm 1.00 Nos 136.15 One Each 136.00
12.42.2 Single pushfit Coupler :
12.42.2.1 75mm 1.00 Nos 93.10 One Each 93.00
12.42.2.2 110mm 1.00 Nos 127.60 One Each 128.00
12.42.3 Single tee with door
12.42.3.1 75x75x75 mm 1.00 Nos 164.20 One Each 164.00
12.42.3.2 110x110x110 mm 1.00 Nos 234.15 One Each 234.00
12.42.4 Single tee without door
12.42.4.1 75x75x75 mm 1.00 Nos 144.30 One Each 144.00
12.42.4.2 110x110x110 mm 1.00 Nos 221.35 One Each 221.00
12.42.5 Bend 87.5°
12.42.5.1 75 mm bend 1.00 Nos 105.90 One Each 106.00
12.42.5.2 110 mm bend 1.00 Nos 150.35 One Each 150.00
12.42.6 Shoe (Plain)
12.42.6.1 75 mm Shoe 1.00 Nos 93.10 One Each 93.00
12.42.6.2 110 mm Shoe 1.00 Nos 131.85 One Each 132.00

DSR - 2023 IN MS EXCEL Page 102 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.43 Providing and fixing unplasticised -PVC pipe clips of
approved design to unplasticised - PVC rain water pipes
by means of 50x50x50 mm hard wood plugs, screwed
with M.S. screws of required length, including cutting
brick work and fixing in cement mortar 1:4 (1 cement :
4 coarse sand) and making good the wall etc. complete.

12.43.1 75 mm 1.00 Nos 369.85 One Each 370.00

12.43.2 110 mm 1.00 Nos 371.30 One Each 371.00
12.44 Providing and fixing to the inlet mouth of rain water 1.00 Nos 54.70 One Each 55.00
pipe cast iron grating 15 cm diameter and weighing not
less than 440 grams.
12.45 Providing and fixing false ceiling at all height including
providing and fixing of frame work made of special
sections, power pressed from M.S. sheets and
galvanized with zinc coating of 120 gms/sqm (both side
inclusive) as per IS : 277 and consisting of angle cleats
of size 25 mm wide x 1.6 mm thick with flanges of 27
mm and 37 mm, at 1200 mm centre to centre, one
flange fixed to the ceiling with dash fastener 12.5 mm
dia x 50 mm long with 6 mm dia bolts, other flange of
cleat fixed to the angle hangers of 25x10x0.50 mm of
required length with nuts & bolts of required size and
other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200
mm centre to centre, to which the ceiling section 0.5
mm thick bottom wedge of 80 mm with tapered flanges
of 26 mm each having lips of 10.5 mm, at 450 mm
centre to centre,

shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of
2.64 mm dia x 230 mm long G.I. wire at every junction,
including fixing perimeter channels 0.5 mm thick 27 mm
high having flanges of 20 mm and 30 mm long, the
perimeter of ceiling fixed to wall/partition with the help
of rawl plugs at 450 mm centre, with 25mm long dry
wall screws @ 230 mm interval, including fixing of
gypsum board to ceiling section and perimeter channel
with the help of dry wall screws of size 3.5 x 25 mm at
230 mm c/c, including jointing and finishing to a flush
finish of tapered and square edges of the board with
recommended jointing compound , jointing tapes ,
finishing with jointing compound in 3 layers covering
upto 150 mm on both sides of joint and two coats of
primer suitable for board, all as per manufacturer's
specification and also including the cost of making
openings for light fittings, grills, diffusers, cutouts made
with frame of perimeter channels suitably fixed, all
complete as per drawings, specification and direction of
the Engineer in Charge but excluding the cost of
painting with :

12.45.1 12.5 mm thick tapered edge gypsum plain board 1.00 Sqm 1355.80 One Square 1356.00
conforming to IS: 2095- (Part I) : 2011 (Board with BIS Metre
certification marks)
12.45.2 12.5 mm thick tapered edge Glass Reinforced Gypsum 1.00 Sqm 1520.10 One Square 1520.00
(GRG) board conforming to IS: 2095- (Part 3) : 1996 Metre
(Board with BIS certification marks)

DSR - 2023 IN MS EXCEL Page 103 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.45.3 12.5 mm thick tapered edge gypsum moisture resistant 1.00 Sqm 1529.10 One Square 1529.00
board. Metre
12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x 1.00 Sqm 1744.15 One Square 1744.00
2400 x 12.5 mm having approx. 15 % perforated area Metre
with perforation size and pattern as approved by the
Engineer-in-charge and as per manufacturer's
specification, with all 4 sides tapered and backed by
acoustical tissue with NRC value not less than 0.60.

12.46 Providing and fixing to the inlet mouth of rain water 1.00 No. 84.55 Each 85.00
pipe PTMT (an Engineering Thermoplastic) grating
square (Slit) 150 mm square with a height of 8 mm and
weighing not less than 100 gms.

12.47 Providing & fixing UV stabilised fiberglass reinforced

plastic sheet roofing up to any pitch, including fixing
with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8 mm
dia. G.I plain/bitumen washers complete but excluding
the cost of purlins, rafters, trusses etc. The sheets shall
be manufactured out of 2400 TEX panel rovigs
incorporating minimum 0.3% ultra-violet stabiliser in
resin system under approximately 2400 psi and hot
cured. They shall be of uniform pigmentation and
thickness without air pockets and shall conform to IS
10192 and IS 12866.The sheets shall be opaque or
translucent, clear or pigmented, textured or smooth as
specified.

12.47.1 2 mm thick corrugated (2.5” or 4.2” or 6”) or step-down 1.00 Sqm 1401.35 One Square 1401.00
(2” or 3” or 6” ) as specified Metre
12.47.2 2mm thick flat. 1.00 Sqm 1245.65 One Square 1246.00
Metre
12.48 Providing & fixing on roof pressed clay tile (Mangalore 1.00 Sqm 433.45 One Square 433.00
tile) of 20 mm nominal thickness and of approved size Metre
and as per approved pattern on steel frame work
complete (steel frame work to be paid separately).

12.49 Providing & laying on roof pressed clay tile ridge 1.00 Sqm 96.90 One Square 97.00
(Mangalore tile) of 20 mm thickness and of approved Metre
pattern on steel frame work complete (steel frame
work to be paid separately).

12.50 Providing and fixing precoated galvanised iron profile 1.00 Sqm 738.65 One Square 739.00
sheets (size, shape and pitch of corrugation as approved Metre
by Engineer-in-Charge) of total coated thickness 0.50
mm (base metal of minimum 0.45 mm thickness with
total coating thickness of 0.05mm) with zinc coating
120 grams per sqm as per IS: 277, in 240 mpa steel
grade, 5-7 microns epoxy primer on both side of the
sheet and polyester top coat 15-18 microns. Sheet
should have protective guard film of 25 microns
minimum to avoid scratches during transportation and
should be supplied in single length upto 12 metre or as
desired by Engineer-in-charge. The sheet shall be fixed
using self drilling /seIf tapping screws of size (5.5x 55
mm) with EPDM seal, complete upto any pitch in
horizontal/ vertical or curved surfaces, excluding the
cost of purlins, rafters and trusses and including cutting
to size and shape wherever required.

DSR - 2023 IN MS EXCEL Page 104 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.51 Providing and fixing precoated galvanised steel sheet
roofing accessories of total coated thickness 0.50 mm
(base metal of minimum 0.45 mm thickness with total
coating thickness of 0.05 mm) with Zinc coating 120
gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7
microns epoxy primer on both side of the sheet and
polyester top coat 15-18 microns using self drilling/ self
tapping screws complete :

12.51.1 Ridges plain (500 - 600mm) 1.00 m 532.35 One Metre 532.00
12.51.2 Flashings/ Aprons.( Upto 600 mm) 1.00 m 485.60 One Metre 486.00
12.51.3 North light curves 1.00 m 546.10 One Metre 546.00
12.51.4 Barge board (Upto 300 mm) 1.00 m 451.50 One Metre 452.00
12.51.5 Crimp curve 1.00 m 496.75 One Metre 497.00
12.51.6 Gutter (600 mm over all girth) 1.00 m 1313.70 One Metre 1314.00
12.52 Providing and fixing tiled false ceiling of specified
materials of size 595x595 mm in true horizontal level,
suspended on inter locking metal grid of hot dipped
galvanized steel sections ( galvanized @ 120 grams/
sqm, both side inclusive) consisting of main "T" runner
with suitably spaced joints to get required length and of
size 24x38 mm made from 0.30 mm thick (minimum)
sheet, spaced at 1200 mm center to center and cross
"T" of size 24x25 mm made of 0.30 mm thick
(minimum) sheet, 1200 mm long spaced between main
"T" at 600 mm center to center to form a grid of
1200x600 mm and secondary cross "T" of length 600
mm and size 24x25 mm made of 0.30 mm thick
(minimum) sheet to be interlocked at middle of the
1200x600 mm panel to form grids of 600x600 mm and
wall angle of size 24x24x0.3 mm and laying false ceiling
tiles of approved texture in the grid including, required
cutting/making, opening for services like diffusers, grills,
light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI

slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to
ceiling with 12.5 mm dia and 50 mm long dash
fasteners, 4 mm GI adjustable rods with galvanised
butterfly level clips of size 85 x 30 x 0.8 mm spaced at
1200 mm center to center along main T, bottom
exposed width of 24 mm of all T-sections shall be pre-
painted with polyester paint, all complete for all heights
as per specifications, drawings and as directed by
Engineer-in-charge.

12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white 1.00 Sqm 1902.95 One Square 1903.00
color tiles of size 595x595 mm, and 0.5 mm thick with 8 Metre
mm drop; made of G I sheet having galvanizing of 100
gms/sqm (both sides inclusive) and electro statically
polyester powder coated of thickness 60 microns
(minimum), including factory painted after bending.

DSR - 2023 IN MS EXCEL Page 105 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.52.2 GI Metal Ceiling Lay in perforated Tegular edge global 1.00 Sqm 2068.75 One Square 2069.00
white color tiles of size 595x595 mm and 0.5 mm thick Metre
with 8 mm drop; made of GI sheet having galvanizing of
100 gms/sqm (both sides inclusive) and 20% perforation
area with 1.8 mm dia holes and having NRC (Noise
Reduction Coefficient ) of 0.5, electro statically
polyester powder coated of thickness60 microns
(minimum), including factory painted after bending and
perforation and backed with a black Glass fiber
acoustical fleece.

12.52.3 12.5 mm thick square edge PVC Laminated Gypsum Tile 1.00 Sqm 2215.15 One Square 2215.00
of size 595x595 mm, made of Gypsum plasterboard, Metre
manufactured from natural gypsum as per IS 2095 part I
and laminated with white 0.16 mm thick fire retardant
PVC film on the face side and 12 micron metalized
polyester on the back side with all edges sealed with
the face side PVC film which goes around and wraps the
edges and is bonded to the edges and the back side
metalized polyester film so as to make the tile a
completely sealed unit.

12.52.4 12.5 mm thick fully Perforated Gypsum Board tile made 1.00 Sqm 1528.00 One Square 1528.00
from plasterboard having glass fibre conforming to IS: Metre
2095 part I, of size 595x595 mm, having perforation of
9.7x9.7 mm at 19.4 mm c/c with center borders of 48
mm and the side borders of 30 mm, backed with non
woven tissue on the back side, having an NRC (Noise
Reduction Coefficient) of 0.79,with 50 mm resin bonded
glass wool backing.

12.54 Providing and fixing GI Clip in Metal Ceiling System of

600x600 mm module which includes providing and
fixing ‘C’ wall angle of size 20x30x20mm made of
0.5mm thick pre painted steel along the perimeter of
the room with help of nylon sleeves and wooden
screws at 300 mm center to centre, suspending the
main C carrier of size 10x38x10mm made of G.I steel
0.7 mm thick from the soffit with help of soffit cleat
37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C
carrier suspension clip and main carrier bracket at 1000
mm c/c. Inverted triangle shaped Spring Tee having
height of 24 mm and width of 34 mm made of GI steel
0.45 mm thick is then fixed to the main C carrier and in
direction perpendicular to it at 600 mm centers with
help of suspension brackets. Wherever the main C
carrier and spring T have to join, C carrier and spring T
connectors have to be used. All sections to be
galvanized @ 120 gms/sqm (both side inclusive), fixing
with clip intiles into spring 'T' with :

12.54.1 GI Metal Ceiling Clip in plain Beveled edge global white 1.00 Sqm 2221.70 One Square 2222.00
color tiles of size 600x600 and 0.5mm thick with 25 mm Metre
height, made of G I sheet having galvanizing of 100
gms/sqm (both sides inclusive) and electro statically
polyester powder coated of thickness 60 microns
(minimum), including factory painted after bending.

DSR - 2023 IN MS EXCEL Page 106 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.54.2 GI Metal Ceiling Clip in plain Beveled edge global white 1.00 Sqm 2354.65 One Square 2355.00
color tiles of size 600x600 and 0.5mm thick with 25 mm Metre
height, made of G I sheet having galvanizing of 100
gms/sqm (both sides inclusive) and 20% perforation
area with 1.8mm dia holes and having NRC of 0.5,
electro statically polyester powder coated of thickness
60 microns (minimum), including factory painted after
bending and perforation.

12.55 Providing and fixing Heat Resistant Terrace Tiles (300 1.00 Sqm 1703.95 One Square 1704.00
mm x 300 mm x 20 mm) with SRI (solar refractive index) Metre
> 78, solar reflection >0.70 and initial emittance >0.75
on waterproof and sloped surface of terrace, laid on 20
mm thick cement sand mortar in the ratio of 1:4 (1
cement : 4coarse sand) and grouting the joints with mix
of white cement & marble powder in ratio of 1:1,
including rubbing and polishing of the surface upto 3
cuts complete, including providing skirting upto 150
mm height along the parapet walls in the same manner.

12.56 Providing and laying roof insulation with 40 mm thick 1.00 Sqm 1570.00 One Square 1570.00
impervious sprayed, closed cell free Rigid Polyurethane Metre
foam over deck insulation conforming to IS - 12432 Pt.
III (density of foam being 40-45 kg/ cum), over a coat of
polyurethane primer applied @ 6-8 sqm per litre, laying
400 G polythene sheet over PUF spray and providing a
wearing course of 40 mm thick cement screed 1:2:4 (1
cement : 2 coarse sand : 4 stone aggregate 20 mm
nominal size) in chequered rough finish, in panels of 2.5
m x 2.5 m and embedding with 24 G wire netting and
sealing the joints with polymerized mastic, all complete
as per direction of Engineer-in-Charge.

12.57 Providing and fixing thermal insulation with Resin 1.00 Sqm 358.50 One Square 359.00
Bonded Fibre glass wool conforming to IS: 8183 having Metre
density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin
Polythene Bags fixed to wall with screw, rawel plug &
washers and held in position by criss crossing GI wire
etc. complete as per directions of Engineer-in-Charge.

12.58 Providing and fixing tiled false ceiling of approved

materials of size 595x595 mm in true horizontal level,
suspended on interlocking metal grid of hot dipped
galvanized steel sections ( galvanized @ 120 grams/
sqm, both side inclusive) consisting of main "T" runner
with suitably spaced joints to get required length and of
size 24x38 mm made from 0.30 mm thick (minimum)
sheet, spaced at 1200 mm center to center and cross
"T" of size 24x25 mm made of 0.30 mm thick
(minimum) sheet, 1200 mm long spaced between main
"T" at 600 mm center to center to form a grid of
1200x600 mm and secondary cross "T" of length 600
mm and size 24x25 mm made of 0.30 mm thick
(minimum) sheet to be interlocked at middle of the
1200x600 mm panel to form grids of 600x600 mm and
wall angle of size 24x24x0.3 mm and laying false ceiling
tiles of approved texture in the grid including, required
cutting/making, opening for services like diffusers, grills,
light fittings, fixtures, smoke detectors etc.

DSR - 2023 IN MS EXCEL Page 107 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
Main "T" runners to be suspended from ceiling using GI
slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to
ceiling with 12.5 mm dia and 50 mm long dash
fasteners, 4 mm GI adjustable rods with galvanized
butterfly level clips of size 85 x 30 x 0.8 mm spaced at
1200 mm center to center along main T, bottom
exposed width of 24 mm of all T-sections shall be pre-
painted with polyester paint, all complete for all heights
as per specifications, drawings and as directed by
Engineer-in-charge.

12.58.1 8 mm thick fully perforated calcium silicate board made 1.00 Sqm 1789.45 One Square 1789.00
with Calcareous & Siliceous materials reinforced with Metre
cellulose fiber manufactured through autoclaving
process to give stable crystalline structure with
minimum compressive strength 225 kg/ sq. cm, bending
strength 100 kg/sq. cm , of size 595x595 mm, having
perforation of dia. 10 mm with minimum perforated
area 18 % with non woven tissue on the back side,
having an NRC (Noise Reduction Coefficient) of 0.85,
with 50 mm thick rockwool of 48 kg /cum backing.

12.59 Providing & fixing false ceiling at all height including

providing & fixing of framework made of special
section, power pressed from M.S. sheets and galvanised
with zinc coating of 120 gms/ sqm ( both side inclusive)
as per IS : 277 and consisting of angle cleat of size
25mm wide x 1.6mm thick with flanges of 27mm and
37mm, at 1200mm c/c, one flange fixed to the ceiling
with dash fastener 12.5mm dia x 50mm long with 6mm
dia bolts, other flange of cleat fixed to the angle
hangers of 25 x10 x0.50mm of required length with
nuts & bolts of required size and other end of angle
hanger fixed with intermediate G.I channels 45 x15 x
0.90mm running at the spacing of 1200 mm c/c, to
which the ceiling section 0.5mm thick bottom wedge of
80mm with tapered flanges of 26 mm each having lips
of 10.5mm, at 450mm c/c, shall be fixed in a direction
perpendicular to G.I intermediate channel with
connecting clip made out of 2.64mm dia x 230mm long
G.I.

DSR - 2023 IN MS EXCEL Page 108 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
wire at every junction, including fixing perimeter
channels 0.50mm thick 27mm high having flanges of
20mm and 30mm long, the perimeter of ceiling fixed to
wall/ partitions with the help of Rawl plugs at 450mm
centre, with 25mm long dry wall screws @ 230mm
interval, including fixing of Calcium Silicate Board to
ceiling section and perimeter channels with the help of
dry wall screws of size 3.5 x25mm at 230mm c/c,
including jointing & finishing to a flush finish of tapered
and square edges of the board with recommended
jointing compounds, jointing tapes, finishing with
jointing compounds in three layers covering up to
150mm on both sides of joints and two coats of primer
suitable for boards, all as per manufacture's
specification and also including the cost of making
opening for light fittings, grills, diffusers, cut outs made
with frame of perimeter channels suitably fixed, all
complete as per drawings, specification and direction of
the Engineer in charge but excluding the cost of
painting with:

12.59.1 8 mm thick Calcium Silicate Board made with 1.00 Sqm 1572.30 One Square 1572.00
Calcareous & Siliceous materials reinforced with Metre
cellulose fiber manufactured through autoclaving
process.

12.60 Providing and fixing thermal insulation of ceiling (under 1.00 Sqm 667.05 One Square 667.00
deck insulation) with Resin Bonded Rockwool Metre
conforming to IS: 8183, density 48 kg/ m3, 50 mm thick,
wrapped in 200 G Virgin Polythene bags fixed to ceiling
with metallic cleats (50x50x3 mm) @ 60 cm and wire
mesh of 12.5mm x 24 gauge wire mesh, for top most
ceiling of building.

12.61 Providing and fixing thermal insulation with Resin 1.00 Sqm 316.05 One Square 316.00
bonded rock wool conforming to IS: 8183, density 48 Metre
kg/m3, 50 mm thick, wrapped in 200 G virgin Polythene
bags placed over existing false ceiling and held in
position by criss- crossing GI wire.

12.62 Providing and fixing thermal insulation with Resin 1.00 Sqm 322.50 One Square 323.00
Bonded rock wool conforming to IS: 8183, having Metre
density 48 kg/m3, 50 mm thick, wrapped in 200 G Virgin
Polythene Bags fixed to wall with screw, rawl plug &
washers and held and in position by criss crossing GI
wire etc. complete as per directions of Engineer-in-
Charge.

12.63 Providing and applying two coats of High Albedo paint 1.00 Sqm 357.60 One Square 358.00
having minimum Solar Reflective Index (SRI) 108 (with Metre
solar reflectance & thermal emittance tested as per
ASTM) C 1549 and ASTM C 1371 respectively), VOC less
than 10 cc/gm. The coating thickness and the
methodology of application shall strictly as per
manufacturer's specifications and as approved by
engineer In charge. Surface preparation includes
cleaning with metal wire brush to remove all dust,
fungus etc., washing with water all complete. The
contractor shall give guarantee for the performance of
SRI and also the durability of coating, all complete as
per direction of Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 109 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.64 Providing & fixing at all heights, levels and locations Mill
finishAluminium alloy roofing sheets of alloy IS
designation 31500, temperHx8 conforming to IS 737
and dimensions as per IS code 2676 withcharacteristics
of good formability and corrosion resistance. Theprofile
sheets shall be fixed to truss members in slope or
requiredpitch or curvature with Hex cap headed self
drilling/tapping Stainlesssteel screws M6, 50 mm long
with 3 mm EPDM seal washer etc. allinclusive of labour,
scaffolding, T&P and sundries etc. complete asper
directions of the Engineer-In-Charge. (Cost of
truss/frame workshall be paid separately).

12.64.1 0.56 mm, Aluminium troughed profile with center to 1.00 Sqm 1034.10 One Square 1034.00
center pitch of 200 mm, depth of 32 mm, overall profile Metre
width1092 mm, cover width 1000mm.
12.64.2 0.71 mm, troughed profile with center to center pitch 1.00 Sqm 1252.75 One Square 1253.00
of 200 mm, depth of 32 mm, overall profile width1092 Metre
mm,cover width 1000mm.
12.64.3 0.91 mm, troughed profile with center to center pitch 1.00 Sqm 1572.80 One Square 1573.00
of 200 mm, depth of 32 mm, overall profile width1092 Metre
mm, cover width 1000mm.
12.64.4 0.56mm Aluminium profile with center to center pitch 1.00 Sqm 1313.70 One Square 1314.00
of175 mm, depth of 46mm, top crest width of Metre
41mm,bottom valley width of 80mm, overall profile
width of1144mm, cover width 1050mm.

12.64.5 0.71mm Aluminium profile with center to center pitch 1.00 Sqm 1616.45 One Square 1616.00
of 175 mm, depth of 46mm, top crest width of 41mm, Metre
bottom valley width of 80mm, overall profile width of
1144mm, cover width 1050mm.

12.64.6 0.91mm Aluminium profile with center to center pitch 1.00 Sqm 2026.40 One Square 2026.00
of 175 mm, depth of 46mm, top crest width of 41mm, Metre
bottom valley width of 80mm, overall profile width of
1144mm, cover width 1050mm.

12.64.7 0.56mm Aluminium Circular (sinusoidal) profile with 1.00 Sqm 1012.15 One Square 1012.00
center to center pitch of 75 mm, depth of 19 mm, Metre
overall profile width 1250mm,cover width 1150mm.
12.64.8 0.71mm Aluminium Circular (sinusoidal) profile with 1.00 Sqm 1256.95 One Square 1257.00
center to center pitch of 75 mm, depth of 19 mm, Metre
overall profile width 1250mm,cover width 1150mm.
12.64.9 0.91mm Aluminium Circular (sinusoidal) profile with 1.00 Sqm 1596.45 One Square 1596.00
center to center pitch of 75 mm, depth of 19 mm, Metre
overall profile width 1250mm,cover width 1150mm.
12.65 Providing & fixing at all heights, levels and locations
colour finish Aluminium alloy roofing sheets of alloy IS
designation 31500, temper Hx8 conforming to IS 737
and dimensions as per IS code 2676 with characteristics
of good formability and corrosion resistance. Theprofile
sheets shall be fixed to truss members in slope or
requiredpitch or curvature with Hex cap headed self
drilling/tapping Stainlesssteel screws M6, 50 mm long
with 3 mm EPDM seal washer etc. allinclusive of labour,
scaffolding, T&P and sundries etc. complete asper
directions of the Engineer-In-Charge. (Cost of
truss/frame workshall be paid separately).

DSR - 2023 IN MS EXCEL Page 110 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
12.65.1 0.56 mm, Aluminium Color coated troughed profile with 1.00 Sqm 1176.70 One Square 1177.00
center to center pitch of 200 mm, depth of 32 mm, Metre
overall profile width1092 mm, cover width 1000mm.

12.65.2 0.71 mm, Aluminium Color coated troughed profile with 1.00 Sqm 1430.20 One Square 1430.00
center to center pitch of 200 mm, depth of 32 mm, Metre
overall profile width1092 mm, cover width 1000mm.

12.65.3 0.91 mm, Aluminium Color coated troughed profile with 1.00 Sqm 1797.75 One Square 1798.00
center to center pitch of 200 mm, depth of 32 mm, Metre
overall profile width1092 mm, cover width 1000mm.

12.65.4 0.56mm Aluminium color profile with center to center 1.00 Sqm 1484.00 One Square 1484.00
pitch of 175 mm, depth of 46mm, top crest width of Metre
41mm, bottom valley width of 80mm, overall profile
width of 1144mm, cover width 1050mm.

12.65.5 0.71mm Aluminium color coated profile with center to 1.00 Sqm 1865.60 One Square 1866.00
center pitch of 175 mm, depth of 46mm, top crest Metre
width of 41mm, bottom valley width of 80mm, overall
profile width of 1144mm, cover width 1050mm.

12.65.6 0.91mm Aluminium color coated profile with center to 1.00 Sqm 2335.45 One Square 2335.00
center pitch of 175 mm, depth of 46mm, top crest Metre
width of 41mm, bottom valley width of 80mm, overall
profile width of 1144mm, cover width 1050mm.

12.65.7 0.56 mm Aluminium profile with center to center pitch 1.00 Sqm 1221.15 One Square 1221.00
of 177.5 mm, depth of 28.5 mm, 987mm overall profile Metre
width, cover width 900mm
12.65.8 0.71 mm Aluminium profile with center to center pitch 1.00 Sqm 1533.00 One Square 1533.00
of 177.5 mm, depth of 28.5 mm, 987mm overall profile Metre
width, cover width 900mm
12.66 Providing and fixing of Pre-coated colour or mill finish
Aluminium Roofing Accessories in 0.71 mm
thickness ,Alloy 31500 (IS designation) [Aluminium Alloy
(AA) 3004 (ISO designation)] For color, coating shall be
5-7 microns epoxy primer on both sides of the sheet
and polyester top coat 15-18 microns, using self
drilling/ tapping SS screws of size 6 x 50mm with 3mm
thick EPDM seal and SS plain washer complete :

12.66.1 Precoated/mill finish aluminium Ridges plain (500- 1.00 m 1066.20 One Running 1066.00
600mm) Metre
12.66.2 Precoated/mill finish aluminium Flashings/ Aprons 1.00 m 977.15 One Running 977.00
(Upto 600 mm) Metre
12.66.3 Precoated/mill finish aluminium North light curves 1.00 m 1055.90 One Running 1056.00
Metre
12.66.4 Precoated/mill finish aluminium Barge board (Upto 200 1.00 m 813.25 One Running 813.00
mm) Metre
12.66.5 Precoated/mill finish aluminium Crimp curve 1.00 m 914.70 One Running 915.00
Metre
12.66.6 Precoated/mill finish aluminium Gutter (600 mm over 1.00 m 1808.65 One Running 1809.00
all girth) Metre
Total of the Sub-Head - Roofing : 115861.00
Sub-Head : Finishing
13.1 12 mm cement plaster of mix :
13.1.1 1:4 (1 cement: 4 fine sand) 1.00 Sqm 347.05 One Square 347.00
Metre

DSR - 2023 IN MS EXCEL Page 111 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.1.2 1:6 (1 cement: 6 fine sand) 1.00 Sqm 333.35 One Square 333.00
Metre
13.2 15 mm cement plaster on the rough side of single or
half brick wall of mix :
13.2.1 1:4 (1 cement: 4 fine sand) 1.00 Sqm 399.45 One Square 399.00
Metre
13.2.2 1:6 (1 cement: 6 fine sand) 1.00 Sqm 383.00 One Square 383.00
Metre
13.3 20 mm cement plaster of mix :
13.3.1 1:4 (1 cement: 4 fine sand) 1.00 Sqm 471.35 One Square 471.00
Metre
13.3.2 1:6 (1 cement: 6 fine sand) 1.00 Sqm 450.00 One Square 450.00
Metre
13.4 12 mm cement plaster of mix :
13.4.1 1:4 (1 cement: 4 coarse sand) 1.00 Sqm 357.35 One Square 357.00
Metre
13.4.2 1:6 (1 cement: 6 coarse sand) 1.00 Sqm 343.65 One Square 344.00
Metre
13.5 15 mm cement plaster on rough side of single or half
brick wall of mix :
13.5.1 1:4 (1 cement: 4 coarse sand) 1.00 Sqm 411.75 One Square 412.00
Metre
13.5.2 1:6 (1 cement: 6 coarse sand) 1.00 Sqm 395.35 One Square 395.00
Metre
13.6 20 mm cement plaster of mix :
13.6.1 1:4 (1 cement: 4 coarse sand) 1.00 Sqm 487.40 One Square 487.00
Metre
13.6.2 1:6 (1 cement: 6 coarse sand) 1.00 Sqm 466.05 One Square 466.00
Metre
13.7 12 mm cement plaster finished with a floating coat of
neat cement of mix :
13.7.1 1:3 (1 cement: 3 fine sand) 1.00 Sqm 439.25 One Square 439.00
Metre
13.7.2 1:4 (1 cement: 4 fine sand) 1.00 Sqm 425.55 One Square 426.00
Metre
13.8 15 mm cement plaster on rough side of single or half
brick wall finished with a floating coat of neat cement
of mix :
13.8.1 1:3 (1 cement: 3 fine sand) 1.00 Sqm 494.30 One Square 494.00
Metre
13.8.2 1:4 (1 cement: 4 fine sand) 1.00 Sqm 477.90 One Square 478.00
Metre
13.9 Cement plaster 1:3 (1 cement: 3 coarse sand) finished
with a floating coat of neat cement.
13.9.1 12 mm cement plaster 1.00 Sqm 449.55 One Square 450.00
Metre
13.9.2 20 mm cement plaster 1.00 Sqm 587.20 One Square 587.00
Metre
13.10 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) 1.00 Sqm 506.60 One Square 507.00
finished with a floating coat of neat cement on the Metre
rough side of single or half brick wall.
13.11 18 mm cement plaster in two coats under layer 12 mm 1.00 Sqm 518.55 One Square 519.00
thick cement plaster 1:5 (1 cement: 5 coarse sand) Metre
finished with a top layer 6mm thick cement plaster 1:6
(1 cement: 6 fine sand).

DSR - 2023 IN MS EXCEL Page 112 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.12 18 mm cement plaster in two coats under layer 12 mm 1.00 Sqm 537.45 One Square 537.00
thick cement plaster 1:5 (1 cement: 5 coarse sand) and Metre
a top layer 6 mm thick cement plaster 1:3 (1 cement: 3
coarse sand) finished rough with sponge.

13.13 12 mm cement plaster 1:2 (1 cement: 2 stone dust) 1.00 Sqm 378.70 One Square 379.00
Metre
13.14 15 mm cement plaster 1:2 (1 cement: 2 stone dust) on 1.00 Sqm 437.20 One Square 437.00
the rough side of single or half brick wall. Metre
13.15 20 mm cement plaster 1:2 (1 cement: 2 stone dust) 1.00 Sqm 520.55 One Square 521.00
Metre
13.16 6 mm cement plaster of mix :
13.16.1 1:3 (1 cement: 3 fine sand) 1.00 Sqm 300.45 One Square 300.00
Metre
13.17 6 mm cement plaster 1:3 (1 cement: 3 fine sand) 1.00 Sqm 396.65 One Square 397.00
finished with a floating coat of neat cement and thick Metre
coat of Lime wash on top of walls when dry for bearing
of R.C.C. slabs and beams.

13.18 Neat cement punning 1.00 Sqm 79.95 One Square 80.00
Metre
13.19 Rough cast plaster upto 10 m height above ground level
with a mixture of sand and gravel or crushed stone
from 6 mm to 10 mm nominal size, dashed over and
including the fresh plaster in two layers, under layer
12mm cement plaster 1:4 (1 cement: 4 coarse sand)
and top layer 10 mm cement plaster 1:3 (1 cement: 3
fine sand) mixed with 10% finely grounded hydrated
lime by volume of cement.

13.19.1 Ordinary cement finish using ordinary cement 1.00 Sqm 886.60 One Square 887.00
Metre
13.20 Pebble dash plaster upto 10 m height above ground 1.00 Sqm 829.95 One Square 830.00
level with a mixture of washed pebble or crushed stone Metre
6mm to 12.5 mm nominal size, dashed over and
including fresh plaster in two layers under layer 12 mm
cement plaster 1:4 (1 cement: 4 coarse sand) and top
layer 10 mm cement plaster with cement mortar 1:3 (1
cement: 3 fine sand) mixed with 10% finely grounded
hydrated lime by volume of cement.

13.21 Extra for providing and mixing water proofing material 1.00 units 22.10 Per 50 kg bag 22.00
in cement plaster work in proportion recommended by of cement
the manufacturers. used in the
mix

13.22 Extra for plastering exterior walls of height more than 1.00 Sqm 87.10 One Square 87.00
10 m from ground level for every additional height of 3 Metre
m or part thereof.
13.23 Extra for plastering on circular work not exceeding 6 m
in radius:
13.23.1 In one coat 1.00 Sqm 47.65 One Square 48.00
Metre
13.23.2 In two coats 1.00 Sqm 72.30 One Square 72.00
Metre
13.24 Extra for plastering done on moulding cornices or
architraves including neat finish to line and level:
13.24.1 In one coat 1.00 Sqm 713.20 One Square 713.00
Metre
13.24.2 In two coats 1.00 Sqm 1175.75 One Square 1176.00
Metre
13.25 Extra for plastering :

DSR - 2023 IN MS EXCEL Page 113 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.25.1 Spherical ceiling 1.00 Sqm 177.60 One Square 178.00
Metre
13.25.2 Groined ceiling 1.00 Sqm 192.30 One Square 192.00
Metre
13.25.3 Flewing soffits 1.00 Sqm 117.65 One Square 118.00
Metre
13.26 Providing and applying plaster of paris putty of 2 mm 1.00 Sqm 262.70 One Square 263.00
thickness over plastered surface to prepare the surface Metre
even and smooth complete.
13.27 Extra for lining out plaster to imitate stone or concrete 1.00 Sqm 113.90 One Square 114.00
blocks walling. Metre
13.28 12 mm thick plain cement mortar bands in cement
mortar 1:4 (1 cement: 4 fine sand) :
13.28.1 Flush Band 1.00 units 7.50 cm per metre 8.00

13.28.2 Sunk Band 1.00 units 8.20 cm per metre 8.00

13.28.3 Raised Band 1.00 units 9.35 cm per metre 9.00

13.28.4 Moulded Band 1.00 units 16.10 cm per metre 16.00

13.29 18 mm thick plain cement mortar band in cement

mortar 1:4 (1 cement: 4 fine sand):
13.29.1 Flush Band 1.00 units 9.05 cm per metre 9.00

13.29.2 Sunk Band 1.00 units 10.00 cm per metre 10.00

13.29.3 Raised Band 1.00 units 11.40 cm per metre 11.00

13.29.4 Moulded Band 1.00 units 21.40 cm per metre 21.00

13.30 18 mm thick moulded cement mortar band in two coats 1.00 units 21.45 cm per metre 21.00
under layer 12 mm thick with cement mortar 1:5 (1
cement: 5 coarse sand) top layer 6mm thick with
cement mortar 1:4 (1 cement: 4 fine sand).

13.31 Pointing on brick work or brick flooring with cement

mortar 1:3 (1 cement: 3 fine sand) :
13.31.1 Flush / Ruled/ Struck or weathered pointing. 1.00 Sqm 257.35 One Square 257.00
Metre
13.31.2 Raised and cut pointing 1.00 Sqm 419.90 One Square 420.00
Metre
13.32 Pointing on tile brick work with cement mortar 1:3 (1
cement: 3 fine sand) :
13.32.1 Flush / Ruled/ Struck or weathered pointing. 1.00 Sqm 350.20 One Square 350.00
Metre
13.33 Pointing on stone work with cement mortar 1:3 (1
cement: 3 fine sand) :
13.33.1 Flush/ Ruled pointing 1.00 Sqm 385.40 One Square 385.00
Metre
13.33.2 Raised and cut pointing 1.00 Sqm 701.05 One Square 701.00
Metre
13.34 Raised and cut pointing on stone work in white cement 1.00 Sqm 716.95 One Square 717.00
mortar 1:3 (1 white cement: 3 marble dust) Metre
13.35 Pointing on stone slab ceiling with cement mortar 1:2 (1
cement: 2 fine sand):
13.35.1 Flush/ Ruled pointing 1.00 Sqm 214.20 One Square 214.00
Metre

DSR - 2023 IN MS EXCEL Page 114 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.36 Extra for pointing on walls on the outside at height 1.00 Sqm 8.65 One Square 9.00
more than 10 m from ground level for every additional Metre
height of 3 m or part there of.
13.37 White washing with lime to give an even shade:
13.37.1 New work (three or more coats) 1.00 Sqm 39.05 One Square 39.00
Metre
13.38 Satna lime wash on walls with one coat 1.00 Sqm 15.75 One Square 16.00
Metre
13.39 Colour washing such as green, blue or buff to give an
even shade :
13.39.1 New work (two or more coats) with a base coat of 1.00 Sqm 53.30 One Square 53.00
white washing with lime Metre
13.39.2 New work (two or more coats) with a base coat of 1.00 Sqm 52.75 One Square 53.00
whiting Metre
13.44 Finishing walls with water proofing cement paint of
required shade :
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 1.00 Sqm 116.90 One Square 117.00
sqm). Metre
13.45 Finishing walls with textured exterior paint of required
shade :
13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 1.00 Sqm 223.60 One Square 224.00
sqm) over and including priming coat of exterior primer Metre
applied @2.20kg/10 sqm.
13.48 Finishing with Deluxe Multi surface paint system for
interiors and exteriors using Primer as per
manufacturers specifications :
13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm. 1.00 Sqm 193.70 One Square 194.00
over and including one coat of Special primer applied @ Metre
0.75 ltr / 10sqm
13.48.2 Painting wood work with Deluxe Multi Surface Paint of 1.00 Sqm 176.25 One Square 176.00
required shade. Two or more coat applied @ 0.90 ltr/10 Metre
sqm over an under coat of primer applied @0.75 ltr/ 10
sqm of approved brand or manufacture

13.48.3 Painting Steel work with Deluxe Multi Surface Paint to 1.00 Sqm 170.70 One Square 171.00
give an even shade. Two or more coat applied @ 0.90 Metre
ltr/10 sqm over an under coat of primer applied @ 0.80
ltr/ 10 sqm of approved brand or manufacture

13.50 Applying priming coat :

13.50.2 With ready mixed aluminium primer of approved brand 1.00 Sqm 74.65 One Square 75.00
and manufacture on resinous wood and plywood. Metre

13.50.3 With ready mixed red oxide zinc chromate primer of 1.00 Sqm 67.40 One Square 67.00
approved brand and manufacture on steel galvanised Metre
iron/steel works
13.50.4 With ready mixed red oxide zinc chromate primer of 1.00 Sqm 36.10 One Square 36.00
approved brand and manufacture on steel work Metre
(second coat)
13.51 Painting with silicon & acrylic emulsion based water
thinnable sealer of approved brand and manufacture
on wet or patchy portion of plastered surfaces:

13.51.1 One coat 1.00 Sqm 101.70 One Square 102.00

Metre
13.51.2 Two coats 1.00 Sqm 161.70 One Square 162.00
Metre

DSR - 2023 IN MS EXCEL Page 115 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.52 Finishing with Epoxy paint (two or more coats) at all
locations prepared and applied as per manufacturer's
specifications including appropriate priming coat,
preparation of surface, etc. complete.

13.52.1 On steel work 1.00 Sqm 241.75 One Square 242.00

Metre
13.52.2 On concrete work 1.00 Sqm 235.15 One Square 235.00
Metre
13.53 Painting on G.S. sheet with synthetic enamel paint of
approved brand and manufacture of required colour to
give an even shade :
13.53.1 New work (two or more coats) including a coat of 1.00 Sqm 180.85 One Square 181.00
approved steel primer but excluding a coat of mordant Metre
solution.
13.54 Applying a coat of mordant solution on G.S. sheet :
13.54.1 With a solution of 38 gms of copper acetate in a litre of 1.00 Sqm 63.35 One Square 63.00
soft water Metre
13.54.2 With a solution made of 13 gms of hydrochloric acid in 1.00 Sqm 63.05 One Square 63.00
a solution of 13 gms each of copper chloride, copper Metre
nitrate and ammonium chloride dissolved in a litre of
soft water.

13.55 Painting (two or more coats) on rain water, soil, waste

and vent pipes and fittings with black anticorrosive
bitumastic paint of approved brand and manufacture,
over and including a priming of ready mixed zinc
chromate yellow primer on new work :

13.55.1 100 mm diameter pipes 1.00 m 76.35 One Metre 76.00

13.55.2 150 mm diameter pipes 1.00 m 113.80 One Metre 114.00
13.56 Painting (two or more coats) on rain water, soil, waste
and vent pipes and fittings with synthetic enamel paint
of approved brand and manufacture and required
colour over a priming coat of approved steel primer on
new work.

13.56.1 100 mm diameter pipes 1.00 m 82.00 One Metre 82.00

13.56.2 150 mm diameter pipes 1.00 m 122.15 One Metre 122.00
13.57 Painting with oil type wood preservative of approved
brand and manufacture:
13.57.1 New work (two or more coats) 1.00 Sqm 54.40 One Square 54.00
Metre
13.58 Providing and applying two coats of fire retardant paint 1.00 Sqm 334.50 One Square 335.00
on cleaned wood/ply surface @ 3.5 sqm per litre per Metre
coat including preparation of base surface as per
recommendations of manufacturer to make the surface
fire retardant.

13.59 Coal tarring two coats on new work using 0.16 and 0.12 1.00 Sqm 66.90 One Square 67.00
litre coal tar per sqm in the first coat and second coat Metre
respectively.
13.61 Painting with synthetic enamel paint of approved brand
and manufacture to give an even shade :
13.61.1 Two or more coats on new work. 1.00 Sqm 155.90 One Square 156.00
Metre
13.62 Painting with synthetic enamel paint of approved brand
and manufacture of required colour to give an even
shade:
13.62.1 Two or more coats on new work over an under coat of 1.00 Sqm 226.25 One Square 226.00
suitable shade with ordinary paint of approved brand Metre
and manufacture.

DSR - 2023 IN MS EXCEL Page 116 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.63 Painting with aluminium paint of approved brand and
manufacture to give an even shade .
13.63.1 Two or more coats on new work 1.00 Sqm 146.80 One Square 147.00
Metre
13.64 Painting with acid proof paint of approved brand and
manufacture of required colour to give an even shade:

13.64.1 Two or more coats on new work. 1.00 Sqm 163.35 One Square 163.00
Metre
13.65 Painting with black anti-corrosive bitumastic paint of
approved brand and manufacture to give an even
shade:
13.65.1 Two or more coats on new work. 1.00 Sqm 140.25 One Square 140.00
Metre
13.67 Varnishing with varnish of approved brand and
manufacture:
13.67.1 Two or more coats of glue sizing with copal varnish over 1.00 Sqm 233.80 One Square 234.00
an under coat of flatting varnish. Metre
13.67.2 Two or more coats glue sizing with spar varnish or an 1.00 Sqm 236.90 One Square 237.00
under coat of flatting varnish. Metre
13.68 French spirit polishing :
13.68.1 Two or more coats on new works including a coat of 1.00 Sqm 446.25 One Square 446.00
wood filler. Metre
13.69 Polishing on wood work with ready mixed wax polish of
approved brand and manufacture :
13.69.1 New work 1.00 Sqm 197.65 One Square 198.00
Metre
13.70 Floor polishing on masonry or concrete floors with wax 1.00 Sqm 96.10 One Square 96.00
polish of approved brand and manufacture. Metre
13.71 Lettering with black Japan paint of approved brand and 1.00 units 6.15 per letter per 6.00
manufacture cm height

13.72 Washed stone grit plaster on exterior walls of height 1.00 Sqm 1162.25 One Square 1162.00
upto 10 metre above ground level, in two layers, under Metre
layer 12mm cement plaster 1:4 (1cement: 4 coarse
sand), furrowing the under layer with scratching tool,
applying cement slurry on the under layer @ 2 Kg of
cement per square metre, top layer 15mm cement
plaster 1:1/2:2 (1 cement: 1/2 coarse sand :2 stone
chipping 10mm nominal size), in panels with groove all
around as per approved pattern, including scrubbing
and washing the top layer with brushes and water to
expose the stone chippings, complete as per
specification and direction of Engineer-in- charge
(Payment for providing grooves shall be made
separately).

13.73 Forming groove of uniform size in the top layer of

washed stone grit plaster as per approved pattern using
wooden battens, nailed to the under layer, including
removal of wooden battens, repair to the edges of
panels and finishing the groove complete as per
specifications and direction of the Engineer-in-charge :

13.73.1 15 mm wide and 15 mm deep groove 1.00 m 75.15 One Metre 75.00
13.73.2 20 mm wide and 15 mm deep groove 1.00 m 75.80 One Metre 76.00
13.74 Extra for washed grit plaster on exterior walls of height 1.00 Sqm 165.85 One Square 166.00
more than 10m from ground level for every additional Metre
height of 3 m or part thereof.

DSR - 2023 IN MS EXCEL Page 117 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.75 Extra for washed stone grit plaster on circular work not 1.00 Sqm 133.55 One Square 134.00
exceeding 6m in radius (in two coats). Metre
13.76 Forming groove of uniform size from 12x12mm and 1.00 m 100.60 One Metre 101.00
upto 25x15mm in the top layer of washed stone grit
plastered surface as per approved pattern, including
providing and fixing aluminum channels of appropriate
size and thickness (not less than 2 mm), nailed to the
under layer with rust proof screws and nails and
finishing the groove complete as per specifications and
direction of the Engineer-in-Charge.

13.77 Extra for using white cement in place of ordinary 1.00 Sqm 76.05 One Square 76.00
cement in the top layer of the item of washed stone grit Metre
plaster.
13.78 Providing and applying 12 mm thick (average) premixed 1.00 Sqm 468.90 One Square 469.00
formulated one coat gypsum lightweight plaster having Metre
additives and light weight aggregates as vermiculite/
per liter respectively conforming to IS: 2547 (Part- 1 &
II) 1976, applied on hacked / uneven background such
as bare brick/block/ RCC work on walls & ceiling at all
floors and locations, finished in smooth line and level
etc. complete.

13.79 Extra for addition of synthetic Polyester triangular fibre 1.00 units 78.35 Per Bag of 78.00
of length 6 mm, effective diameter 10-40 microns and 50kg of
specific gravity of 1.34 to 1.40 in cement plaster/mortar Cement
by using 125 gms. of synthetic Polyester triangular fibre
for 50 Kgs. cement used in cement mortar as per
directions of Engineer-in-Charge.

13.80 Providing and applying white cement based putty of 1.00 Sqm 156.05 One Square 156.00
average thickness 1 mm, of approved brand and Metre
manufacturer, over the plastered wall surface to
prepare the surface even and smooth complete.

13.81 Distempering with 1st quality acrylic distemper (ready

mixed) having VOC (Volatile Organic Compound )
content less than 50 gram/ litre, of approved brand and
of required shade and colour complete to give and even
shade.

13.81.1 Old work (one or more coats) 1.00 Sqm 62.70 One Square 63.00
Metre
13.82 Wall painting with acrylic emulsion paint, having VOC
(Volatile Organic Compound ) content less than 50
grams/ litre, of approved brand and manufacture,
including applying additional coats wherever required,
to achieve even shade and colour.

13.82.1 One coat. 1.00 Sqm 92.00 One Square 92.00

Metre
13.82.2 Two coats. 1.00 Sqm 137.45 One Square 137.00
Metre
13.83 Wall painting with premium acrylic emulsion paint of
interior grade, having VOC (Volatile Organic
Compound ) content less than 50 grams/ litre. of
approved brand and manufacture, including applying
additional coats wherever required to achieve even
shade and colour.

13.83.1 One coat. 1.00 Sqm 95.45 One Square 95.00

Metre
13.83.2 Two coats. 1.00 Sqm 142.80 One Square 143.00
Metre

DSR - 2023 IN MS EXCEL Page 118 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.85 Applying priming coats with primer of approved brand
and manufacture, having low VOC (Volatile Organic
Compound ) content.
13.85.1 With ready mixed pink or grey primer on wood work 1.00 Sqm 70.35 One Square 70.00
(hard and soft wood) having VOC content less than 50 Metre
grams/ litre.
13.85.3 With water thinnable cement primer on wall surface 1.00 Sqm 73.95 One Square 74.00
having VOC content less than 50 grams/litre. Metre
13.86 6 mm plaster on cement concrete or reinforced cement 1.00 Sqm 269.15 One Square 269.00
concrete work with white cement based polymer Metre
modified self curing mortar of approved make as per
the direction of Engineer-In-Charge.

13.87 White washing with lime to give an even shade :

13.87.1 Old work (two or more coats) . 1.00 Sqm 22.85 One Square 23.00
Metre
13.87.2 Old work (one or more coats) . 1.00 Sqm 13.90 One Square 14.00
Metre
13.88 Removing white or colour wash by scrapping and sand 1.00 Sqm 19.75 One Square 20.00
papering and preparing the surface smooth including Metre
necessary repairs to scratches etc. complete

13.92 Painting on G.S. sheet with synthetic enamel paint of

approved brand and manufacture of required colour to
give an even shade :
13.92.1 Old work (one or more coats) . 1.00 Sqm 93.30 One Square 93.00
Metre
13.93 Painting (two or more coats) on rain water, soil, waste
and vent pipes and fittings with black anticorrosive
bitumastic paint of approved brand and manufacture
over and including a priming coat of ready mixed zinc
chromate yellow primer on new work :

13.93.1 75 mm diameter pipes . 1.00 m 57.25 One Metre 57.00

13.94 Painting (one or more coats) on rain water, soil, waste
and vent pipes and fittings with black anticorrosive
bitumastic paint of approved brand and manufacture
on old work :

13.94.1 75 mm diameter pipes . 1.00 m 26.85 One Metre 27.00

13.94.2 100 mm diameter pipes . 1.00 m 35.50 One Metre 36.00
13.94.3 150 mm diameter pipes . 1.00 m 51.20 One Metre 51.00
13.95 Painting (two or more coats) on rain water, soil, waste
and vent pipes and fittings with aluminium paint of
approved brand and manufacture over a priming coat
of ready mixed zinc chromate yellow primer on new
work :

13.95.1 75 mm diameter pipes . 1.00 m 58.90 One Metre 59.00

13.95.2 100 mm diameter pipes . 1.00 m 81.45 One Metre 81.00
13.95.3 150 mm diameter pipes . 1.00 m 121.35 One Metre 121.00
13.96 Painting (one or more coats) on rain water, soil, waste
and vent pipes and fittings with synthetic enamel paint
of approved brand and manufacture and required
colour on old work :

13.96.1 75 mm diameter pipes . 1.00 m 28.20 One Metre 28.00

13.96.2 100 mm diameter pipes . 1.00 m 36.25 One Metre 36.00
13.96.3 150 mm diameter pipes . 1.00 m 52.25 One Metre 52.00
13.97 Painting with oil type wood preservative of approved
brand and manufacture :
13.97.1 Old work (one or more coats) . 1.00 Sqm 41.20 One Square 41.00
Metre

DSR - 2023 IN MS EXCEL Page 119 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.99 Painting with synthetic enamel paint of approved brand
and manufacture of required colour to give an even
shade :
13.99.1 One or more coats on old work. 1.00 Sqm 102.80 One Square 103.00
Metre
13.100 Painting with aluminium paint of approved brand and
manufacture to give an even shade :
13.100.1 One or more coats on old work. 1.00 Sqm 96.00 One Square 96.00
Metre
13.101 Painting with acid proof paint of approved brand and
manufacture of required colour to give an even shade :

13.101.1 One or more coats on old work. 1.00 Sqm 107.25 One Square 107.00
Metre
13.102 Painting with black anti-corrosive bitumastic paint of
approved brand and manufacture to give an even shade
:
13.102.1 One or more coats on old work. 1.00 Sqm 93.70 One Square 94.00
Metre
13.103 French spirit polishing :
13.103.1 One or more coats on old work. 1.00 Sqm 224.80 One Square 225.00
Metre
13.104 Polishing on wood work with ready made wax polish of
approved brand and manufacture :
13.104.1 Old work . 1.00 Sqm 99.80 One Square 100.00
Metre
13.105 Re-lettering with black Japan paint of approved brand 1.00 units 3.85 Per Letter Per 4.00
and manufacture. Cm Height

13.106 Painting (one or more coats) with black Japan paint of 1.00 Sqm 95.80 One Square 96.00
approved brand and manufacture to give an even Metre
shade.
13.107 Providing and fixing C.P. brass chain and rubber plug
complete for sink or wash basin :
13.107.1 32 mm dia. 1.00 No. 80.10 Each 80.00
13.107.2 40 mm dia. 1.00 No. 78.65 Each 79.00
13.109 Finishing walls with water proofing cement paint of
required shade :
13.109.1 Old work (one or more coats applied @ 2.20 kg/10 sqm) 1.00 Sqm 112.90 One Square 113.00
over priming coat of primer applied @ 0.80 litrs/10 sqm Metre
complete including cost of Priming coat.
13.109.2 Old work (one or more coats @ 2.20 kg/10 sqm) 1.00 Sqm 75.80 One Square 76.00
complete. Metre
13.110 Finishing walls with textured exterior paint of required
shade :
13.110.1 Old work (Two or more coats on existing cement paint 1.00 Sqm 169.20 One Square 169.00
surface applied @ 3.28 ltr/10 sqm. Metre
13.110.2 Old work (One or more coats) applied @ 1.82 ltr/10 1.00 Sqm 109.10 One Square 109.00
sqm. Metre
13.111 Finishing walls with Acrylic Smooth exterior paint of
required shade :
13.111.1 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) 1.00 Sqm 120.75 One Square 121.00
on existing cement paint surface). Metre
13.111.2 Old work (One or more coat applied @ 0.90 ltr/10 sqm). 1.00 Sqm 80.65 One Square 81.00
Metre
13.112 Finishing walls with Premium Acrylic Smooth exterior
paint with Silicone additives of required shade :
13.112.1 Old work (Two or more coats applied @ 1.43 ltr/ 10 1.00 Sqm 131.30 One Square 131.00
sqm) over existing cement paint surface. Metre

DSR - 2023 IN MS EXCEL Page 120 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
13.112.2 Old work (one or more coats applied @ 0.83 ltr/10 1.00 Sqm 88.55 One Square 89.00
sqm). Metre
13.113 Varnishing with varnish of approved brand and
manufacture:
13.113.1 One or more coats with copal varnish. 1.00 Sqm 94.60 One Square 95.00
Metre
13.113.2 One or more coats with spar varnish. 1.00 Sqm 95.05 One Square 95.00
Metre
13.114 Melamine polishing on wood work (one or more coat). 1.00 Sqm 1192.30 One Square 1192.00
Metre
13.115 Varnishing with flatting varnish of approved brand and 1.00 Sqm 99.70 One Square 100.00
manufacture one or more coats on old work. Metre
13.116 Polishing in high gloss/matt finish melamine clear polish 1.00 Sqm 3049.85 One Square 3050.00
on wood work in required color/wooden shade texture Metre
with following process in the sequence as detailed
below:

1. The surface to be polished is rubbed with sand paper

80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and

allowing sufficient drying time for 1st coat and 2nd coat
is allowed to dry for 8 to 12 hrs.
3. On drying of sealer coat, wet rubbing with emery
cloth of finer grading with water to remove excess
sealer layer and make the surface further smooth after
this wet rubbing, then surface is applied with special
grade melamine fillers to fill all the small and big
holes/grooves etc. Filler coat to be allowed to dry for 4
to 6 hrs on which again a light wet rubbing is done this
surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with

spray gun using melamine clear polish and melamine
thinner in required proportion. This 1st coat is allowed
to dry for 24 hrs then this dry surface is again fine wet
rubbed smooth, which is further allowed to dry for 12
hrs. The final melamine polish is applied with
compressor pressure spray gun using melamine clear
polish and melamine thinner mixed in required
proportion complete as per direction of Engineer-in-
Charge. (Finalo coat to be done in 1 or 2 layers without
gap of time.)

Total of the Sub-Head - Finishing : 35009.00

Sub-Head : Repairs to Buildings
14.1 Repairs to plaster of thickness 12 mm to 20 mm in
patches of area 2.5 sq.meters and under, including
cutting the patch in proper shape, raking out joints and
preparing and plastering the surface of the walls
complete, including disposal of rubbish to the dumping
ground, all complete as per direction of Engineer-in-
harge.

14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand). 1.00 Sqm 547.40 One Square 547.00
Metre
14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand). 1.00 Sqm 560.50 One Square 561.00
Metre

DSR - 2023 IN MS EXCEL Page 121 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.2 Fixing chowkhats in existing opening including
embedding chowkhats in floors or walls cutting
masonry for holdfasts, embedding hold fasts in cement
concrete blocks of size 15 x 10 x 10 cm with cement
concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size), painting two
coats of approved wood preservative to sides of
chowkhats and making good the damages to walls and
floors as required complete, including disposal of
rubbish to the dumping ground, all complete as per
directions of Engineer-In-Charge.

14.2.1 Door chowkhats . 1.00 No. 1782.55 Each 1783.00

14.2.2 Window chowkhats . 1.00 No. 1125.15 Each 1125.00
14.2.3 Clerestory window chowkhats . 1.00 No. 851.00 Each 851.00
14.3 Fixing chowkhat in existing opening in brick / RCC wall 1.00 No. 217.10 Each 217.00
with dash fasteners/Chemical fasteners of appropriate
size (3 nos on each vertical member of door chowkhat
and 2 nos on each vertical member of window
chowkhats), including Cost of dash fasteners/ chemical
fastener.

14.4 Making the opening in brick masonry including

dismantling in floor or walls by cutting masonry and
making good the damages to walls, flooring and jambs
complete, to match existing surface i/c disposal of
mulba/rubbish to the nearest municipal dumping
ground, all complete as per directions of Engineer-In-
Charge.

14.4.1 For door/ window/ clerestory window. 1.00 Sqm 1264.35 One Square 1264.00
Metre
14.5 Renewing glass panes, with putty and nails wherever
necessary including racking out the old putty:
14.5.1 Float glass panes of nominal thickness 4 mm (weight 1.00 Sqm 1090.65 One Square 1091.00
not less than 10kg/sqm). Metre
14.5.2 Float glass panes of nominal thickness 5 mm (weight 1.00 Sqm 1416.15 One Square 1416.00
not less than 12.5kg/sqm). Metre
14.6 Renewing glass panes, with wooden fillets wherever
necessary:
14.6.1 Float glass panes of nominal thickness 4 mm (weight 1.00 Sqm 1580.90 One Square 1581.00
not less than 10kg/sqm). Metre
14.6.2 Float glass panes of nominal thickness 5 mm (weight 1.00 Sqm 1906.40 One Square 1906.00
not less than 12.5kg/sqm). Metre
14.7 Renewing glass panes and refixing existing wooden
fillets:
14.7.1 Float glass panes of nominal thickness 4 mm (weight 1.00 Sqm 1227.30 One Square 1227.00
not less than 10kg/sqm). Metre
14.7.2 Float glass panes of nominal thickness 5 mm (weight 1.00 Sqm 1552.75 One Square 1553.00
not less than 12.5kg/sqm). Metre
14.8 Supplying and fixing new wooden fillets wherever
necessary:
14.8.1 2nd class teak wood fillets . 1.00 m 77.70 One Running 78.00
Metre
14.8.2 Hollock wood fillets. 1.00 m 70.75 One Running 71.00
Metre
14.9 Renewal of old putty of glass panes (length) . 1.00 m 56.15 One Running 56.00
Metre
14.10 Refixing old glass panes with putty and nails . 1.00 Sqm 729.85 One Square 730.00
Metre
14.11 Fixing old glass panes with wooden fillets (excluding 1.00 Sqm 679.60 One Square 680.00
cost of fillets) . Metre

DSR - 2023 IN MS EXCEL Page 122 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.12 Providing and fixing 16 mm M.S. Fan clamps of standard 1.00 No. 563.90 Each 564.00
shape and size in existing R.C.C. slab including cutting
chase, anchoring clamp to reinforcement bar, including
cleaning, refilling, making good the chase with matching
concrete, plastering and painting the exposed portion
of the clamps complete.

14.13 Regrading terracing of mud phaska covered with tiles or 1.00 Sqm 696.05 One Square 696.00
brick, in cement by dismantling tiles or bricks, removing Metre
mud plaster, preparing the surface of mud phaska to
proper slope, relaying mud plaster gobri leaping and
tiles or bricks, grouted in cement mortar 1:3 (1 cement :
3 fine sand) including replacing unserviceable tiles or
bricks with new ones and disposal of unserviceable
material to the dumping ground (the cost of the new
tiles or brick excluded), all complete as per directions of
Engineer-In-Charge.

14.14 Replacing sand stone slabs in roofing, laid in cement

mortar 1:4 (1 cement : 4 coarse sand) including
necessary repairs and cement pointing with same
mortar complete including disposal of rubbish to
dumping ground, all complete as per directions of
Engineer-In-Charge.

14.14.1 Red/ white sand stone slabs 30 to 50 mm thick. 1.00 Sqm 1365.85 One Square 1366.00
Metre
14.15 Renewing wooden battens in roofs, including making
good the holes in wall and painting with oil type wood
preservative of approved brand and manufacture
complete including removal of rubbish to the dumping
ground, all complete as per directions of Engineer-In-
Charge.

14.15.1 Sal wood battens. 1.00 Cum 99120.65 One Cubic 99121.00
Metre
14.16 Renewing wooden beams in roofs including making
good the holes in walls and painting with oil type wood
preservative of approved brand and manufacture
complete including removal of rubbish to the dumping
ground, all complete as per directions of Engineer-In-
Charge.

14.16.1 Not exceeding 4.00 metres in length.

14.16.1.1 Sal wood beams . 1.00 Cum 104573.95 One Cubic 104574.00
Metre
14.16.1.2 Hollock wood beams . 1.00 Cum 70271.70 One Cubic 70272.00
Metre
14.16.2 Above 4.00 metres and upto 5.00 metres length.
14.16.2.1 Sal wood beams . 1.00 Cum 107320.00 One Cubic 107320.00
Metre
14.16.2.2 Hollock wood beams . 1.00 Cum 72987.25 One Cubic 72987.00
Metre
14.17 Raking out joints in lime or cement mortar and 1.00 Sqm 72.45 One Square 72.00
preparing the surface for re-pointing or replastering Metre
including disposal of rubbish to the dumping ground, all
complete as per directions of Engineer-In-Charge.

14.18 Flush pointing with cement mortar 1:3 (1 cement : 3

fine sand) mixed with 2% of integral water proofing
compound by weight of cement for flat tile bricks on
top of mud phaska :

14.18.1 With F.P.S. brick tiles 1.00 Sqm 137.70 One Square 138.00
Metre

DSR - 2023 IN MS EXCEL Page 123 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.18.2 With modular brick tiles 1.00 Sqm 139.05 One Square 139.00
Metre
14.19 Taking out wind ties from roof including cutting out 1.00 Kg 5.40 One Kilogram 5.00
rusted bolts, nuts etc. and removing materials to any
distance within compound and stacking.
14.20 Fixing of old wind tie with new fittings including 1.00 m 126.00 One Running 126.00
painting two or more coats with anticorrosive Metre
bitumastic paint of approved brand & manufacturer
over and including priming coat of ready mixed zinc
chromate yellow primer of approved brand.

14.21 Renewing bottom rail and/or top runner of collapsible 1.00 m 298.85 One Kilogram 299.00
gate including making good all damages and applying
priming coat of zinc chromate yellow primer of
approved brand and manufacturer.

14.22 Renewing Wrought iron or M.S. Wheel or roller of steel

door or gate and fitting and fixing the same with
necessary clamps, nuts and bolts / welding and erection
etc. complete.

14.22.1 Wheel 50 mm dia. and below. 1.00 wheel 123.70 Per Wheel 124.00
14.22.2 Wheel above 50 mm dia. 1.00 wheel 304.55 Per Wheel 305.00
14.23 Pumping out water caused by springs, tidal or river 1.00 kLtr 231.05 One Kilo Litre 231.00
seepage, broken water mains or drains and the like.
14.25 Brick work with common burnt clay bricks of class 1.00 Cum 6207.25 One Cubic 6207.00
designation 7.5 in mud mortar Metre
14.26 Providing and fixing 25 mm thick shutters for cup board
etc. :
14.26.1 Panelled or panelled & glazed shutters :
14.26.1.1 Superior class teak wood including nickel plated bright 1.00 Sqm 5127.00 One Square 5127.00
finished M.S. piano hinges with necessary screws. Metre

14.26.1.2 Ist class teak wood including nickel plated bright 1.00 Sqm 4484.85 One Square 4485.00
finished M.S. piano hinges with necessary screws. Metre
14.26.2 Glazed shutters :
14.26.2.1 Superior class teak wood including nickel plated bright 1.00 Sqm 5054.05 One Square 5054.00
finished M.S. piano hinges with necessary screws. Metre

14.26.2.2 Ist class teak wood including nickel plated bright 1.00 Sqm 4362.45 One Square 4362.00
finished M.S. piano hinges with necessary screws. Metre
14.27 Providing and fixing plain jaffri door and window
shutters including bright or/and black enamelled M.S.
butt hinges with necessary screws 35x10mm laths
placed 35mm apart (frames to be paid separately)
including fixing 50x12mm beading complete with :

14.27.1 Second class teak wood. 1.00 Sqm 4602.65 One Square 4603.00
Metre
14.28 Providing and fixing brass curtain rods of wall thickness
1.25mm with two brass brackets fixed with brass
screws and wooden plugs etc. wherever necessary
complete.

14.28.1 20 mm diameter. 1.00 m 343.50 One Running 344.00

Metre
14.28.2 25 mm diameter. 1.00 m 421.75 One Running 422.00
Metre
14.29 Providing and fixing M.S. round or square bars with 1.00 Kg 120.75 One Kilogram 121.00
M.S. flats at required spacing in wooden frames of
windows and clerestory windows.

DSR - 2023 IN MS EXCEL Page 124 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.30 Providing joists (karries) including hoisting, fixing in
position and applying wood preservative on unexposed
surface etc. complete with:
14.30.1 Sal wood. 1.00 Cum 97978.30 One Cubic 97978.00
Metre
14.30.2 Hollock wood. 1.00 Cum 64022.85 One Cubic 64023.00
Metre
14.31 Providing and fixing bright finished brass single acting
spring hinges with necessary brass screws etc. complete
:
14.31.1 150 mm . 1.00 No. 765.05 Each 765.00
14.31.2 125 mm . 1.00 No. 546.00 Each 546.00
14.31.3 100 mm . 1.00 No. 485.65 Each 486.00
14.32 Providing and fixing bright finished brass double acting
spring hinges with necessary brass screws etc. complete
:
14.32.1 150 mm 1.00 No. 851.85 Each 852.00
14.32.2 125 mm 1.00 No. 726.65 Each 727.00
14.32.3 100 mm 1.00 No. 704.75 Each 705.00
14.33 Providing and fixing bright finished brass flush bolts
with necessary brass screws etc. complete :
14.33.1 250 mm 1.00 No. 285.05 Each 285.00
14.33.2 150 mm 1.00 No. 245.35 Each 245.00
14.33.3 100 mm 1.00 No. 188.45 Each 188.00
14.34 Providing and fixing 150 mm bright finished floor brass 1.00 No. 271.45 Each 271.00
door stopper with rubber cushion, necessary brass
screws etc. to suit shutter thickness complete .
14.35 Providing and fixing bright finished brass hard drawn
hooks and eyes :
14.35.1 300 mm 1.00 No. 101.85 Each 102.00
14.35.2 250 mm 1.00 No. 97.70 Each 98.00
14.35.3 200 mm 1.00 No. 87.75 Each 88.00
14.35.4 150 mm 1.00 No. 70.55 Each 71.00
14.35.5 100 mm 1.00 No. 61.85 Each 62.00
14.36 Providing and fixing bright finished brass fan light pivot 1.00 No. 47.30 Each 47.00
with necessary brass screws etc. complete.
14.37 Providing and fixing 300 mm long bright finished brass 1.00 No. 74.80 Each 75.00
chain with hook for fan light including necessary brass
screws etc. complete.
14.38 Providing and fixing bright finished brass quadrant stay 1.00 No. 191.45 Each 191.00
300mm long with necessary brass screws etc. complete.

14.39 Providing and fixing bright finished brass helical door 1.00 No. 543.95 Each 544.00
spring (superior quality).
14.40 Providing and fixing chromium plated brass butt hinges
with necessary chromium plated brass screws etc.
complete.
14.40.1 125x70x4 mm (ordinary type) . 1.00 No. 171.05 Each 171.00
14.40.2 100x70x4 mm (ordinary type) . 1.00 No. 148.75 Each 149.00
14.40.3 75x65x4 mm (heavy type) . 1.00 No. 181.00 Each 181.00
14.40.4 75x40x2.5 mm (ordinary type) . 1.00 No. 102.60 Each 103.00
14.40.5 50x40x2.5 mm (ordinary type) . 1.00 No. 47.60 Each 48.00
14.41 Providing and fixing 85x42mm chromium plated brass 1.00 No. 278.60 Each 279.00
pull bolt lock with necessary chromium plated brass
screws, nuts, bolts and washers etc. complete.

DSR - 2023 IN MS EXCEL Page 125 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.72 Providing and fixing double scaffolding system (cup lock 1.00 Sqm 338.25 One Square 338.00
type) on the exterior side, up to seven story height Metre
made with 40 mm dia M.S. tube 1.5 m centre to centre,
horizontal & vertical tubes joining with cup & lock
system with M.S. tubes, M.S. tube challies, M.S. clamps
and M.S. staircase system in the scaffolding for working
platform etc. and maintaining it in a serviceable
condition for the required duration as approved and
removing it there after. The scaffolding system shall be
stiffened with bracings, runners, connection with the
building etc wherever required for inspectionof work at
required locations with essential safety features for the
workmen etc. complete as per directions and approval
of Engineer-in-charge. The elevational area of the
scaffolding shall be measured for payment purpose. The
payment shall be made once irrespective of duration of
scaffolding.Note: - This item to be used for
maintenance work judicially, necessary deduction for
scaffolding in the existing item to be done.

14.73 Providing and fixing bright finished brass casement 1.00 Kg 557.20 One Kilogram 557.00
window fasteners or peg stays to windows/ ventilators
with necessary welding and machine screws etc.
complete.

14.74 Providing and fixing 14 mm bright finished brass spring 1.00 No. 68.35 Each 68.00
catch to steel centre hung ventilators with necessary
welding and machine screws etc. complete.

14.75 Repair to plaster of thickness 12mm to 20 mm in 1.00 Sqm 670.95 One Square 671.00
patches of area 2.5 sqm and under, including cutting Metre
the patch in proper shape, raking out joints and
preparing plastering the wall surface with white cement
based polymer modified self curing mortar, including
disposal of rubbish, all complete as per the direction of
Engineer-In- Charge.

14.75A Cleaning of terrace/loft water storage tank (inside 1.00 Ltr 0.50 One Litre 1.00
surface area) upto 2000 litre capacity at all heights with
coconut brushes, duster etc., removal of silt, rubbish
from the tank and cleaning the tank with fresh water
disinfecting with bleaching powder @ 0.5gm per litre
capacity of tank, including marking the date of cleaning
on the side of tank body with the help of stencil and
paint and disposing of malba, all complete as per
direction of Engineer-in-Charge. (The old date already
written on tank should be removed with paint remover
or black paint and if date is not written with the stencil
or old date is not removed deduction will be made @
Rs. 0.10 per litre if during cleaning any GI fittings or ball
cock is damaged that is to be repaired by contractor at
his own cost and nothing extra will be paid on this
account)

14.76 Cleaning and de-silting of gully trap chamber, including 1.00 No. 108.30 Each 108.00
removal of rubbish mixed with earth etc. and disposal
of same, all as per the direction of Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 126 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.77 Cleaning of chocked sewer line by diesel running vehicle 1.00 m 340.75 One Metre 341.00
mounting hydraulic operated high pressure suction cum
jetting sewer cleaning machine fitted with pump having
4000 litres suction capacity and 6000 litres water jetting
tank capacity including skilled operator, supervising
engineer etc. for cleaning and partial de-silting of
manholes and de-chocking of sewer lines. De-chocking
and flushing of sewer line from one manhole to another
by high pressure jetting system of 2200 PSI for sewer
line from 150mm dia upto 300mm dia for all depth.

14.78 Cleaning of under ground sump, Over Head R.C.C. Tank

(independent staging) including disposal of slit and
rubbish, all as per direction of Engineer-in-Charge. The
cleaning shall consist following operations:-

(i) Tank shall be emptied of water by pumping & bottom

shall be cleaned of slit and other deposits.
(ii) Entire surface area of the sump shall then scrubbed
thoroughly with wire brush etc. and pressure washed
with water.
(iii) Chlorination of RCC internal surface by liquid
chlorine.
(iv) The treated surface shall be dried using air jetting
and all loose particles shall be removal from the
surface.
(v) Finally the surface shall be treated with ultraviolet 1.00 Sqm 422.70 One Square 423.00
radiation etc. as per direction of Engineer-in-Charge. Metre
14.79 Disconnecting damaged overhead/terrace PVC water 1.00 No. 433.75 Each 434.00
storage tank of any size from water supply line and
removing from the terrace including shifting at ground
level as per direction of Engineer-in- charge.

14.80 Providing & fixing White vitreous china water closet

squatting pan (Indian type) along with "S" or "P" trap
including dismantling of old WC seat and "S" or "P" trap
at site complete with all operations including all
necessary materials, labour and disposal of dismantled
material i/c malba, all complete as per the direction of
Engineer-in charge.

14.80.1 Long pattern W.C Pan of size 580x440 mm 1.00 No. 3501.70 Each 3502.00
14.80.2 Orissa pattern W.C Pan of size 580x440 mm 1.00 No. 4478.75 Each 4479.00
14.81 Cutting holes of required size in brick masonry wall for 1.00 No. 288.10 Each 288.00
fixing of exhaust fan including providing and fixing 300
mm dia PVC pipe conforming BIS-12818 and making
good the same etc. complete as per direction of
Engineer-in-charge.

14.82 Dismantling W.C. Pan of all sizes including disposal of 1.00 No. 134.10 Each 134.00
dismantled materials i/c malba all complete as per
directions of Engineer-in- Charge.
14.83 Hacking of CC flooring including cleaning for surface etc. 1.00 Sqm 3.45 One Square 3.00
complete as per direction of the Engineer-in-Charge. Metre

14.84 Dismantling 15 to 40 mm dia G.I. pipe including stacking

of dismantled pipes (within 50 metres lead) as per
direction of Engineerin-Charge.
(a) Internal Work- Exposed on wall 1.00 m 3.25 One Metre 3.00

DSR - 2023 IN MS EXCEL Page 127 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.85 Taking out existing wooden door shutter, repair by 1.00 No. 429.10 Each 429.00
cutting, painting etc. and refixing of repaired door
shutters to existing door frames, including replacement
of hinges with screws, etc. as required, all complete as
per the direction of the Engineer-in-charge.

14.86 Providing and laying in situ seven course water proofing

treatment with APP (Atactic poly-propylene) modified
Polymeric membrane over roof consisting of first coat
of bitumen primer @ 0.40Kg per sqm, 2nd, 4th & 6th
courses of bonding material @ 1.20 Kg/sqm, which shall
consist of blown type bitumen of grade 85/25
conforming to IS : 702, 3rd and 5th layers of roofing
membrane APP modified Polymeric membrane 1.5mm
thick of 2.25 Kg/sqm weight consisting of five layers
prefabricated with centre core as 20micron HMHDPE
film sandwiched on both sides with polymeric mix and
the polymeric mix is protected on both side with
20micron HMHDPE film.

7th, the top most layer shall be finished with brick tiles 1.00 Sqm 730.55 One Square 731.00
of class designation 10 grouted with cement mortar Metre
1:3(1cement:3 fine sand) mixed with 2% integral water
proofing compound by weight of cement over a 12mm
layer of cement mortar 1:3 (1 cement: 3 fine sand) and
finished neat ( item of laying brick tiles shall be paid for
separately).

14.87 Providing and laying in situ five course water proofing

treatment with APP (Atactic Polypropylene) modified
Polymeric memberane over roof consisting of first coat
of bitumen primer @ 0.40 litre per sqm, 2nd & 4th
courses of bonding material @ 1.20 kg/sqm, which shall
consist of blown type bitumen of grade 85/25
conforming to IS : 702, 3rd layer of roofing membrane
APP modified Polymeric membrane 2.0 mm thick of
3.00 Kg/ sqm weight consisting of five layers
prefabricated with centre core as 100 micron HMHDPE
film sandwiched on both sides with polymeric mix and
the polymeric mix is protected on both side with 20
micron HMHDPE film. 5th, the top most layer shall be
finished with brick tiles of class designation 10 grouted
with cement mortar 1:3 (1 cement : 3 fine sand) mixed
with 2% integral water proofing compound by weight of
cement over a 12 mm layer of cement mortar 1:3 (1
cement : 3 fine sand) and finished neat (item of laying
brick tiles shall be paid for separately).

7th, the top most layer shall be finished with brick tiles 1.00 Sqm 532.05 One Square 532.00
of class designation 10 grouted with cement mortar 1:3 Metre
(1cement : 3 fine sand) mixed with 2% integral water
proofing compound by weight of cement over a 12 mm
layer of cement mortar 1:3 (1 cement : 3 fine sand) and
finished neat (item of laying brick tiles shall be paid for
separately).

DSR - 2023 IN MS EXCEL Page 128 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
14.88 Providing and laying in situ seven course water proofing
treatment with APP (Atactic Polypropylene) modified
Polymeric memberane over roof consisting of first coat
of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th
courses of bonding material @ 1.20 kg/sqm, which shall
consist of blown type bitumen of grade 85/25
conforming to IS : 702, 3rd and 5th layers of roofing
membrane APP modified Polymeric membrane 2.0 mm
thick of 3.00 Kg/sqm weight consisting of five layers
prefabricated with centre core as 100 micron HMHDPE
film sandwiched on both sides with polymeric mix and
the polymeric mix is protected on both side with 20
micron HMHDPE film.

7th, the top most layer shall be finished with brick tiles 1.00 Sqm 855.70 One Square 856.00
of class designation 10 grouted with cement mortar 1:3 Metre
(1 cement : 3 fine sand) mixed with 2% integral water
proofing compound by weight of cement over a 12 mm
layer of cement mortar 1:3 ( 1 cement : 3 fine sand) and
finished neat (item of laying brick tiles shall be paid for
separately).

14.89 Providing and fixing APP (Atactic Polypropylene

Polymer) modified prefabricated five layer 2 mm thick
water proofing membrane , black finished reinforced
with glass fibre matt consisting of a coat of bitumen
primer for bitumen membrane @ 0.40 litre/sqm by the
samemembrance manufacture of density at 25°C, 0.87 -
0.89 kg/ litre and viscocity 70 - 160 cps. Over the primer
coat the layer of membrane shall be laid using Butane
torch and sealing all joints etc., and preparing the
surface complete.

The vital physical and chemical parameters of the

membrane shall be as under : Joint strength in
longitudinal and transverse direction at 23°C as
350/300 N/ 5 cm. Tear strength in longitudinal and
transverse direction as 60/80N. Softening point of
membrane not less than 150°C. Cold flexibility shall be
upto -2°C when tested in accordance with ASTM, D -
5147. The laying of membrane shall be got done
through the authorised applicator of the manufacture
of membrane.

14.89.1 2mm (for corrugated roof sheets) 1.00 Sqm 498.35 One Square 498.00
Metre
14.90 Providing and laying APP (Atactic Polypropylene
Polymer) modified prefabricated five layer, 3 mm thick
water proofing membrane, black finished reinforced
with glass fibre matt consisting of a coat of bitumen
primer for bitumen membrane @ 0.40 litre/sqm by the
samemembrane manufactured of density at 25°C, 0.87 -
0.89 kg/litre and viscocity 70 - 160 cps. Over the primer
coat the layer of membrane shall be laid using butane
torch and sealing all joints etc., and preparing the
surface complete. The vital physical and chemical
parameters of the membrane shall be as under : Joint
strength in longitudinal and transverse direction at 23°C
as 350/300 N/5 cm.

DSR - 2023 IN MS EXCEL Page 129 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
Tear strength in longitudinal and transverse direction as
60/80N. Softening point of membrane not less than
150°C. Cold flexibility shall be upto -2°C when tested in
accordance with ASTM, D - 5147. The laying of
membrane shall be got done through the authorised
applicator of the manufacturer of membrane :

14.90.1 3 mm thick 1.00 Sqm 537.45 One Square 537.00

Metre
14.91 Providing and laying APP (Atactic Polypropylene
Polymer) modified prefabricated five layer 3 mm thick
water proofing membrane, black finished reinforced
with non-woven polyester matt consisting of a coat of
bitumen primer for bitumen membrane @ 0.40
litre/sqm by the same membrane manufacture of
density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160
cps. Over the primer coat the layer of membrane shall
be laid using Butane Torch and sealing all joints etc, and
preparing the surface complete.

The vital physical and chemical parameters of the

membrane shall be as under : Joint strength in
longitudinal and transverse direction at 23°C as 650/
450N/ 5cm. Tear strength in longitudinal and transverse
direction as 300/250N. Softening point of membrane
not less than 150°C. Cold flexibility shall be upto -2°C
when tested in accordance with ASTM, D - 5147. The
laying of membrane shall be got done through the
authorised applicator of the manufacturer of
membrane :

14.91.1 3 mm thick 1.00 Sqm 560.95 One Square 561.00

Metre
14.92 Extra for covering top of membrane with Geotextile, 1.00 Sqm 88.90 One Square 89.00
120 gsm non woven, 100% polyester of thickness 1 to Metre
1.25 mm bonded to the membrane with intermittent
touch by heating the membrane by Butane Torch as per
manufactures recommendation.

14.93 Providing round the clock security guard without gun 1.00 job 1308.40 Each Job 1308.00
for watch & ward of Government premises and its all
belongings by deploying neatly dressed security guards
in 8 hour’s shift including necessary T&P like torch, lathi
and uniform etc.complete,as per the direction of
Engineer-in-charge.(One job means 8 hour’s duty).

14.94 Providing round the clock security guard with gun for 1.00 job 1416.50 Each Job 1417.00
watch & ward of Government premises and its all
belongings by deploying neatly dressed security guards
in 8 hour’s shift including necessary T&P like torch, lathi
and uniform etc.complete, as per the direction of
Engineer-in-charge. (One job means 8 hour’s duty).

Total of the Sub-Head - Repairs To Buildings : 693389.00

Sub-Head : Dismantling and Demolishing
15.1 Demolishing lime concrete manually/ by mechanical 1.00 Cum 851.50 One Cubic 852.00
means and disposal of material within 50 metres lead as Metre
per direction of Engineer in-charge

DSR - 2023 IN MS EXCEL Page 130 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
15.2 Demolishing cement concrete manually/ by mechanical
means including disposal of material within 50 metres
lead as per direction of Engineer - in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent 1.00 Cum 2434.25 One Cubic 2434.00
design mix) Metre
15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent 1.00 Cum 1503.60 One Cubic 1504.00
design mix) Metre
15.3 Demolishing R.C.C. work manually/ by mechanical 1.00 Cum 3551.25 One Cubic 3551.00
means including stacking of steel bars and disposal of Metre
unserviceable material within 50 metres lead as per
direction of Engineer - in- charge.

15.4 Demolishing R.B. work manually/ by mechanical means 1.00 Cum 3177.25 One Cubic 3177.00
including stacking of steel bars and disposal of Metre
unserviceable material within 50 metres lead as per
direction of Engineer-in- charge.

15.5 Extra for cutting reinforcement bars manually/ by 1.00 Sqm 1147.20 One Square 1147.00
mechanical means in R.C.C. or R.B. work (Payment shall Metre
be made on the cross sectional area of R.C.C. or R.B.
work) as per direction of Engineer in-charge.

15.6 Extra for scrapping, cleaning and straightening 1.00 Kg 9.05 One Kilogram 9.00
reinforcement from R.C.C. or R.B. work.
15.7 Demolishing brick work manually/ by mechanical means
including stacking of serviceable material and disposal
of unserviceable material within 50 metres lead as per
direction of Engineer-in-charge..

15.7.1 In mud mortar 1.00 Cum 704.90 One Cubic 705.00

Metre
15.7.2 In lime mortar with old mughal bricks 1.00 Cum 1783.35 One Cubic 1783.00
Metre
15.7.3 In lime mortar 1.00 Cum 851.50 One Cubic 852.00
Metre
15.7.4 In cement mortar 1.00 Cum 2060.20 One Cubic 2060.00
Metre
15.8 Removing mortar from bricks and cleaning bricks
including stacking within a lead of 50 m (stacks of
cleaned bricks shall be measured):
15.8.1 From brick work in mud mortar 1.00 Units 4658.45 1000 nos 4658.00
15.8.2 From brick work in lime mortar 1.00 Units 5355.30 1000 nos 5355.00
15.8.3 From brick work in cement mortar 1.00 Units 6700.80 1000 nos 6701.00
15.9 Demolishing stone rubble masonry manually/ by
mechanical means including stacking of serviceable
material and disposal of unserviceable material within
50 metres lead as per direction of Engineer-in-charge :

15.9.1 In lime mortar 1.00 Cum 1158.10 One Cubic 1158.00

Metre
15.9.2 In cement mortar 1.00 Cum 2458.95 One Cubic 2459.00
Metre
15.10 Dismantling dressed stone work ashlar face stone work,
marble work or precast concrete work manually/ by
mechanical means including stacking of serviceable and
disposal of unserviceable material within 50 metres
lead as per direction of Engineer-in-charge :

15.10.1 In lime mortar 1.00 Cum 1464.25 One Cubic 1464.00

Metre
15.10.2 In cement mortar 1.00 Cum 2877.75 One Cubic 2878.00
Metre

DSR - 2023 IN MS EXCEL Page 131 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
15.11 Removing mortar from and cleaning stones and
concrete articles (net quantity of stacks of cleaned
materials will be measured):
15.11.1 In lime mortar 1.00 Cum 478.55 One Cubic 479.00
Metre
15.11.2 In cement mortar 1.00 Cum 689.20 One Cubic 689.00
Metre
15.12 Dismantling doors, windows and clerestory windows
(steel or wood) shutter including chowkhats, architrave,
holdfasts etc. complete and stacking within 50 metres
lead :

15.12.1 Of area 3 sq. metres and below 1.00 No. 367.20 Each 367.00
15.12.2 Of area beyond 3 sq. metres 1.00 No. 502.75 Each 503.00
15.13 Taking out doors, windows and clerestory window
shutters (steel or wood) including stacking within 50
metres lead:
15.13.1 Of area 3 sq. metres and below 1.00 No. 143.50 Each 144.00
15.13.2 Of area beyond 3 sq. metres 1.00 No. 188.90 Each 189.00
15.14 Dismantling wood work in frames, trusses, purlins and
rafters up to 10 metres span and 5 metres height
including stacking the material within 50 metres lead :

15.14.1 Of sectional area 40 square centimetres and above. 1.00 Cum 4459.10 One Cubic 4459.00
Metre
15.14.2 Of sectional area below 40 square centimetres. 1.00 m 17.85 One Running 18.00
Metre
15.15 Extra for dismantling trusses, rafters, purlins etc. of
wood work for every additional span of one metre or
part thereof beyond 10 metres :
15.15.1 Of sectional area 40 square centimetres and above 1.00 units 589.55 Cum per 590.00
metre span
15.15.2 Of sectional area below 40 square centimetres 1.00 unit 1.65 Metre per 2.00
metre span
15.16 Extra for dismantling trusses, rafters, purlins etc. of
wood work for every additional height of one metre or
part thereof beyond 5 metres :
15.16.1 Of sectional area 40 square centimetres and above. 1.00 ubits 857.00 Cum per 857.00
metre height
15.16.2 Of sectional area below 40 square centimetres. 1.00 unit 3.40 Metre per 3.00
metre height
15.17 Dismantling steel work in single sections including
dismembering and stacking within 50 metres lead in:
15.17.1 R.S. Joists 1.00 Kg 3.40 One Kilogram 3.00

15.17.2 Channels, angles, tees and flats 1.00 Kg 2.30 One Kilogram 2.00

15.18 Dismantling steel work in built up sections in angles, 1.00 Kg 5.65 One Kilogram 6.00
tees, flats and channels including all gusset plates, bolts,
nuts, cutting rivets, welding etc. including
dismembering and stacking within 50 metres lead.

15.19 Dismantling steel work manually/ by mechanical means 1.00 Kg 3.85 One Kilogram 4.00
in built up sections without dismembering and stacking
within 50 metres lead as per direction of Engineer-in-
charge

15.20 Extra for dismantling trusses, rafters, purlins etc. of 1.00 unit 0.85 Kg per metre 1.00
steel work for every additional span of one metre or span
part thereof beyond 10 metres

DSR - 2023 IN MS EXCEL Page 132 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
15.21 Extra for dismantling trusses, rafters, purlins etc. of 1.00 unit 0.85 Kg per metre 1.00
steel work for every additional height of one metre or height
part thereof beyond 5 metres.
15.22 Extra for marking of structural steel work required to be 1.00 Kg 4.65 One Kilogram 5.00
re-erected.
15.23 Dismantling tile work in floors and roofs laid in cement
mortar including stacking material within 50 metres
lead.
15.23.1 For thickness of tiles 10 mm to 25 mm 1.00 Sqm 73.40 One Square 73.00
Metre
15.23.2 For thickness of tiles above 25 mm and up to 40 mm 1.00 Sqm 113.35 One Square 113.00
Metre
15.24 Demolishing dry brick pitching in floors, drains etc. 1.00 Cum 1317.65 One Cubic 1318.00
including stacking of serviceable material and disposal Metre
of unserviceable material within 50 metres lead :

15.25 Dismantling stone slab flooring laid in cement mortar 1.00 Sqm 266.45 One Square 266.00
including stacking of serviceable material and disposal Metre
of unserviceable material within 50 metres lead

15.26 Demolishing brick tile covering in terracing including 1.00 Sqm 105.35 One Square 105.00
stacking of serviceable material and disposal of Metre
unserviceable material within 50 metres lead.
15.27 Demolishing mud phaska in terracing and disposal of 1.00 Cum 914.30 One Cubic 914.00
material within 50 metres lead. . Metre
15.28 Dismantling roofing including ridges, hips, valleys and
gutters etc., and stacking the material within 50 metres
lead of:
15.28.1 G.S. Sheet 1.00 Sqm 164.95 One Square 165.00
Metre
15.28.2 Asbestos cement sheet 1.00 Sqm 77.30 One Square 77.00
Metre
15.29 Dismantling stone slab roofing over wooden karries or 1.00 Cum 2664.65 One Cubic 2665.00
R.C.C. battens (dismantling karries and battens to be Metre
paid for separately), including stacking of serviceable
material and disposal of unserviceable material within
50 metres lead.

15.30 Dismantling jack arch roofing and floors including 1.00 Sqm 253.90 One Square 254.00
stacking of serviceable material and disposal of Metre
unserviceable material within 50 metres lead.
15.31 Dismantling tiled roofing with battens, boarding etc. 1.00 Sqm 209.90 One Square 210.00
complete including stacking of serviceable material and Metre
disposal of unserviceable material within 50 metres
lead.

15.32 Demolishing thatch roofing including mats, bamboo, 1.00 Sqm 57.70 One Square 58.00
jaffari etc. complete including stacking of serviceable Metre
material and disposal of unserviceable material within
50 metres lead.

15.33 Dismantling wooden ballies in posts and struts including 1.00 m 20.95 One Running 21.00
stacking within 50 metres lead. Metre
15.34 Dismantling and stacking within 50 metres lead, fencing
posts or struts including all earth work and dismantling
of concrete etc. in base of:
15.34.1 T’ or ‘L’ iron or pipe 1.00 No. 230.90 Each 231.00
15.34.2 R.C.C. 1.00 No. 243.30 Each 243.00
15.35 Cutting ballies or wooden posts of fencing at the point 1.00 No. 13.45 Each 13.00
of projection above the concrete or ground and
stacking the same within 50 metres lead.

DSR - 2023 IN MS EXCEL Page 133 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
15.36 Dismantling barbed wire or flexible wire rope in fencing 1.00 Kg 36.80 One Kilogram 37.00
including making rolls and stacking within 50 metres
lead.
15.37 Dismantling wooden trellis work excluding frames but 1.00 Sqm 64.85 One Square 65.00
including stacking the serviceable material within 50 Metre
metres lead..
15.38 Dismantling expanded metal or I.R.C. fabrics with 1.00 Sqm 75.80 One Square 76.00
necessary battens and beading including stacking the Metre
serviceable material within 50 metres lead.
15.39 Dismantling wooden boardings in lining of walls and
partitions, excluding supporting members but including
stacking within 50metres lead :
15.39.1 Up to 10 mm thick 1.00 Sqm 61.00 One Square 61.00
Metre
15.39.2 Thickness above 10 mm up to 25 mm 1.00 Sqm 77.75 One Square 78.00
Metre
15.39.3 Thickness above 25 mm up to 40 mm 1.00 Sqm 90.35 One Square 90.00
Metre
15.40 Dismantling precast concrete or stone slabs in walls,
partition walls etc. including stacking within 50 metres
lead :
15.40.1 Thickness up to 40 mm 1.00 Sqm 289.30 One Square 289.00
Metre
15.40.2 Thickness above 40 mm up to 75 mm 1.00 Sqm 433.55 One Square 434.00
Metre
15.41 Dismantling cement asbestos or other hard board 1.00 Sqm 56.35 One Square 56.00
ceiling or partition walls including stacking of Metre
serviceable materials and disposal of unserviceable
materials within 50 metres lead.

15.42 Dismantling C.I. or asbestos rain water pipe with fittings

and clamps including stacking the material within 50
metres lead :
15.42.1 75 to 80 mm dia pipe. 1.00 m 75.70 One Running 76.00
Metre
15.42.2 100 mm dia pipe 1.00 m 78.00 One Running 78.00
Metre
15.42.3 150 mm dia pipe 1.00 m 80.25 One Running 80.00
Metre
15.43 Dismantling manually/ by mechanical means including
stacking of serviceable material and disposal of
unserviceable material within 50 metres lead as per
direction of Engineer-in-charge :

15.43.1 Water bound macadam road 1.00 Sqm 217.45 One Square 217.00
Metre
15.43.2 Bituminous road 1.00 Sqm 428.50 One Square 429.00
Metre
15.44 Dismantling G.I. pipes (external work) including
excavation and refilling trenches after taking out the
pipes, manually/ by mechanical means including
stacking of pipes within 50 metres lead as per direction
of Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore 1.00 m 149.80 One Running 150.00

Metre
15.44.2 Above 40 mm nominal bore 1.00 m 161.40 One Running 161.00
Metre

DSR - 2023 IN MS EXCEL Page 134 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
15.45 Dismantling C.I. pipes including excavation and refilling
trenches after taking out the pipes, manually/ by
mechanical means breaking lead caulked joints, melting
of lead and making into blocks including stacking of
pipes & lead at site within 50 metre lead as per
direction of Engineer-in-charge:

15.45.1 Up to 150 mm diameter 1.00 m 332.40 One Running 332.00

Metre
15.45.2 Above 150 mm dia up to 300 mm dia. 1.00 m 456.65 One Running 457.00
Metre
15.45.3 Above 300 mm diameter 1.00 m 614.30 One Running 614.00
Metre
15.46 Dismantling steel cylinder R.C. pipes including
excavation and refilling trenches after taking out the
pipes, manually/ by mechanical means breaking lead
caulked joints, melting of lead and making into blocks
including stacking of pipes & lead at site within 50
metres lead as per direction of Engineer-in-charge :

15.46.1 Up to 600 mm diameter 1.00 m 695.25 One Running 695.00

Metre
15.46.2 Above 600 mm diameter 1.00 m 1752.45 One Running 1752.00
Metre
15.47 Dismantling asbestos cement pressure pipes including
excavation and refilling trenches after taking out the
pipes manually/ by mechanical means and stacking the
pipes within 50 metres lead as per direction of
Engineer-in-charge :

15.47.1 Up to 150 mm diameter 1.00 m 332.15 One Running 332.00

Metre
15.47.2 Above 150 mm diameter 1.00 m 403.05 One Running 403.00
Metre
15.48 Taking out C.I. cover with frame from R.C.C. top slab of 1.00 No. 697.40 Each 697.00
manholes of various sizes including demolishing of
R.C.C. work manually/ by mechanical means and
stacking of useful materials near the site and disposal of
unserviceable materials within 50 metres lead as per
direction of Engineer-in-charge.

15.49 Taking out C.I. cover with frame from R.C.C. top slab of 1.00 No. 406.75 Each 407.00
inspection chambers of various sizes including
demolishing of R.C.C. work manually/ by mechanical
means and stacking of useful materials near the site
and disposal of unserviceable materials within 50
metres lead as per direction of Engineer-in-charge.

15.50 Dismantling of R.C.C. spun vent shaft including 1.00 No. 4623.70 Each 4624.00
excavating the cement concrete pit completely, taking
out the shaft, refilling the excavated gap, stacking the
useful materials near the site and disposal of
unserviceable materials within 50 metres lead.

15.51 Dismantling of road gully chamber of various sizes 1.00 No. 958.75 Each 959.00
including C.I. grating with frame including stacking of
useful materials near the site and disposal of
unserviceable materials within 50metres lead including
refilling the excavated gap.

15.52 Dismantling of flushing cistern of all types 1.00 No. 112.05 Each 112.00
(C.I./PVC/Vitreous China) including stacking of useful
materials near the site and disposal of unserviceable
materials within 50 metres lead.

DSR - 2023 IN MS EXCEL Page 135 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
15.53 Dismantling of C.I. sluice valve including stacking of
useful materials within a lead of 50 metres
15.53.1 Up to 150 mm diameter 1.00 No. 319.50 Each 320.00
15.53.2 Above 150 mm diameter 1.00 No. 1184.15 Each 1184.00
15.54 Dismantling of spindle fire hydrant including stacking of 1.00 No. 726.35 Each 726.00
useful materials within 50 metres lead.
15.55 Dismantling of cement concrete platform along with
curtain walls and base concrete etc. including stacking
of useful materials near the site and disposal of
unserviceable materials within 50 metres lead :

15.55.1 120 x 120 cm (outside to outside) 1.00 No. 1104.05 Each 1104.00
15.55.2 210 x 120 cm (outside to outside) 1.00 No. 1693.35 Each 1693.00
15.55.3 320 x 120 cm (outside to outside) 1.00 No. 2396.95 Each 2397.00
15.56 Dismantling old plaster or skirting raking out joints and 1.00 Sqm 54.65 One Square 55.00
cleaning the surface for plaster including disposal of Metre
rubbish to the dumping ground within 50 metres lead.

15.57 Dismantling aluminium/ Gypsum partitions, doors, 1.00 Sqm 56.35 One Square 56.00
windows, fixed glazing and false ceiling including Metre
disposal of unserviceable material and stacking of
serviceable material with in 50 meters lead as directed
by Engineer-in-charge.

15.58 Demolishing R.C.C. work by mechanical means and 1.00 Cum 2818.90 One Cubic 2819.00
stockpiling at designated locations and disposal of Metre
dismantled materials up to a lead of 1 kilometre,
stacking serviceable and unserviceable material
separately including cutting reinforcement bars.

15.59 Dismantling of flexible pavement (bituminous courses) 1.00 Cum 420.80 One Cubic 421.00
by mechanical means and disposal of dismantled Metre
material up to a lead of 1 kilometre, as per direction of
Engineer-in-charge.

15.60 Disposal of building rubbish / malba / similar 1.00 Cum 263.95 One Cubic 264.00
unserviceable, dismantled or waste materials by Metre
mechanical means, including loading, transporting,
unloading to approved municipal dumping ground or as
approved by Engineer-in-charge, beyond 50 m initial
lead, for all leads including all lifts involved.

Total of the Sub-Head - Dismantling And Demolishing : 82595.00

Sub-Head : Road Work
16.1 Preparation and consolidation of sub grade with power 1.00 Sqm 218.90 One Square 219.00
road roller of 8 to 12 tonne capacity after excavating Metre
earth to an average of 22.5 cm depth, dressing to
camber and consolidating with road roller including
making good the undulations etc. and re- olling the sub
grade and disposal of surplus earthwith lead upto 50
metres.

16.2 Extra for compaction of earth work in embankment 1.00 Cum 24.85 One Cubic 25.00
under optimum moisture conditions to give at least 95% Metre
of the maximum dry density (proctor density).
16.3 Supplying and stacking at site.
16.3.1 90 mm to 45 mm size stone aggregate. 1.00 Cum 2098.40 One Cubic 2098.00
Metre
16.3.2 63 mm to 45 mm size stone aggregate. 1.00 Cum 1636.05 One Cubic 1636.00
Metre
16.3.3 53 mm to 22.4 mm size stone aggregate. 1.00 Cum 1842.30 One Cubic 1842.00
Metre
16.3.4 Over burnt (Jhama) brick aggregate 120 mm to 40 mm. 1.00 Cum 798.10 One Cubic 798.00
Metre

DSR - 2023 IN MS EXCEL Page 136 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.3.5 Over burnt (Jhama) brick aggregate 90 mm to 45 mm. 1.00 Cum 872.05 One Cubic 872.00
Metre
16.3.6 Stone screening 13.2 mm nominal size (Type A). 1.00 Cum 2034.35 One Cubic 2034.00
Metre
16.3.7 Stone screening 11.2 mm nominal size (Type B). 1.00 Cum 2247.75 One Cubic 2248.00
Metre
16.3.8 Red bajri 1.00 Cum 1564.90 One Cubic 1565.00
Metre
16.3.9 Good earth. 1.00 Cum 775.50 One Cubic 776.00
Metre
16.3.10 Moorum. 1.00 Cum 768.25 One Cubic 768.00
Metre
16.4 Laying, spreading and compacting stone aggregate of 1.00 Cum 1046.95 One Cubic 1047.00
specified sizes to WBM specifications in uniform Metre
thickness, hand picking, rolling with 3 wheeled road /
vibratory roller 8-10 tonne capacity in stages to proper
grade and camber, applying and brooming requisite
type of screening / binding material to fill up interstices
of coarse aggregate, watering and compacting to the
required density

16.5 Laying water bound macadam sub-base with brick

aggregate and binding material, earth etc. including
screening, sorting and spreading to template and
consolidation with light power road-roller etc.
complete.(payment for brick aggregate and moorum
etc. to be made separately)

16.5.1 Over burnt (Jhama) brick aggregate 120 mm to 40 mm. 1.00 Cum 879.70 One Cubic 880.00
Metre
16.5.2 Over burnt (Jhama) brick aggregate 90 mm to 45 mm. 1.00 Cum 879.70 One Cubic 880.00
Metre
16.6 Supplying, stacking and Spreading 6 mm thick red bajri,
watering and rolling complete including preparation of
the surface and rolling.
16.6.1 With road roller/ hand roller. 1.00 Sqm 24.45 One Square 24.00
Metre
16.7 Brick edging in full brick width and half brick depth
including excavation, refilling and disposal of surplus
earth lead upto 50 metres.
16.7.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 194.30 One Running 194.00
class designation 7.5 Metre
16.8 Brick edging laid lengthwise with half brick depth
including excavation, refilling and disposal of surplus
earth lead upto 50 metres :
16.8.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 53.45 One Running 53.00
class designation 7.5 Metre
16.9 Scarifying metalled (water-bound) road surface 1.00 Sqm 33.30 One Square 33.00
including disposal of rubbish, lead upto 50m and Metre
consolidation of the aggregate received from scarifying
with power road roller of 8 to 10 tonne capacity.

16.10 Making bajri path including preparation of sub grade, 1.00 Sqm 191.25 One Square 191.00
supplying and laying brick aggregate of 50mm nominal Metre
size 7.5 cm deep with binding material consisting of 12
mm moorum and 12 mm red bajri consolidated with
road roller.

16.11 Dry stone pitching 22.5 cm thick including supply of 1.00 Sqm 883.15 One Square 883.00
stones and preparing surface complete. Metre
16.12 Dry brick pitching half brick thick in drains including
supply of bricks and preparing the surface complete :

DSR - 2023 IN MS EXCEL Page 137 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.12.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 Sqm 644.05 One Square 644.00
class designation 7.5 Metre
16.13 Cutting road and making good the same including
supply of extra quantities of materials i.e. aggregate,
moorum screening, red bajri and labour required.
16.13.1 bituminous portion 1.00 Cum 5032.25 One Cubic 5032.00
Metre
16.13.2 Water bound macadam. 1.00 Cum 3078.05 One Cubic 3078.00
Metre
16.14 Cutting bajri paths and making good the same including 1.00 Sqm 284.20 One Square 284.00
supply of extra quantities of brick aggregate, moorum Metre
and red bajri required.
16.15 Supplying at site :
16.15.1 R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 1.00 Cum 32891.20 One Cubic 32891.00
(1 cement : 1.5 coarse sand : 3 graded stone aggregate Metre
12.5 mm nominal size) with wooden plugs or 6mm bar
nibs wherever required as per direction of Engineer-in-
charge (cost of earth works in excavation, concrete
works in foundation to be paid separately).

16.15.2 Welded steel wire fabric of required width having 1.00 Kg 78.95 One Kilogram 79.00
rectangular mesh painted with two or more coats of
enamel paint of approved shade over a coat of primer
(Priming & Painting to be paid for separately).

16.16 Supplying and fixing turn buckles and straining bolts for 1.00 sets 274.30 Each set 274.00
barbed wire fencing.
16.17 Fencing with R.C.C. post placed at required distance,
embedded in cement concrete blocks, every 15th post,
last but one end post and corner post shall be strutted
on both sides and end post one side only, provided with
horizontal lines and two diagonals of barbed wire
weighing 9.38 kg per 100 metres (minimum), between
the two posts fitted and fixed with G.I. staples on
wooden plugs or G.I. binding wire tied to 6 mm bar nibs
fixed while casting the post (cost of R.C.C. posts, struts,
earth work and concrete to be paid for separately) :-
Payment to be made per metre cost of total length of
barbed wire used.

16.17.1 With G.I. barbed wire 1.00 m 14.00 One Running 14.00
Metre
16.18 Fencing with angle iron post placed at required distance
embedded in cement concrete blocks, every 15th post,
last but one end post and corner post shall be strutted
on both sides and end post on one side only and
provided with horizontal lines and two diagonals
interwoven with horizontal wires, of barbed wire
weighing 9.38 kg per 100 m (minimum), between the
two posts fitted and fixed with G.I. staples, turn buckles
etc. complete. (Cost of posts, struts, earth work and
concrete work to be paid for separately). Payment to be
made per metre cost of total length of barbed wire
used.

16.18.1 With G.I. barbed wire 1.00 m 22.10 One Running 22.00
Metre
16.19 Supplying at site Angle iron post & strut of required size 1.00 Kg 125.75 One Kilogram 126.00
including bottom to be split and bent at right angle in
opposite direction for 10 cm length and drilling holes
upto 10 mm dia. etc. complete.

DSR - 2023 IN MS EXCEL Page 138 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.20 Welded steel wire fabric fencing with posts of specified 1.00 Sqm 66.15 One Square 66.00
material and of standard design placed and embedded Metre
in cement concrete blocks 45x45x 60 cm of mix 1:5:10
(1 cement:5 fine sand : 10 graded stoneaggregate 40
mm nominal size), every 15th post, last but one end
post and corner post shall be strutted on both sides and
end post on one side only and struts embedded in
cement concrete blocks 70x45x50 cm of the same mix,
provided with welded steel wire fabricfixed between
the posts fitted and fixed with G.I. staples on wooden
plugs or tied to 6 mm bar nibs with G.I. binding wire
(cost of posts, welded steel wire fabric, painting, earth
work in excavation and concrete to be paid for
separately).

16.21 Engraving letters in hard stone 1.00 units 10.55 per cm height 11.00
per letter

16.22 Providing and fixing 15x15x90cm boundary stone of 1.00 No. 252.90 Each 253.00
hard stone with top 30 cm chisel dressed on all four
sides including top (cost of excavation, refilling and
concrete etc. to be paid for separately).

16.23 Providing and fixing 15cm dia at top, 20cm at bottom 1.00 No. 852.40 Each 852.00
and 90cm high precast reinforced cement concrete
1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone
aggregate 20mm nominal size) boundary stone as per
standard design including finishing smooth with cement
mortar 1:3 (1 cement : 3 fine sand)(cost of excavation,
refilling and concreting to be paid for separately).

16.24 Providing and fixing precast reinforced cement concrete

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone
aggregate 20mm nominal size) kilo metre stone as per
standard design including finishing smooth in 1:3
cement mortar(1 cement : 3 fine sand) but excluding
the cost of earth work, concrete in foundation, painting
and lettering etc. which shall be paid for separately.

16.24.1 35x111x25 cm size. 1.00 No. 2876.70 Each 2877.00

16.24.2 50x152.5x25 cm size. 1.00 No. 5170.25 Each 5170.00
16.24.3 35x93.5x18 cm size. 1.00 No. 1924.50 Each 1925.00
16.25 Surface dressing on new surface with paving bitumen of 1.00 Sqm 225.35 One Square 225.00
grade VG - 10 of approved quality using 2.25 kg of Metre
bitumen per sqm with 1.65 cum of stone chippings 13.2
mm nominal size per 100 sqm of road surface, including
consolidation with road roller of 6 to 8 tonne capacity
etc. complete:

16.26 Surface dressing on new surface in two coats with 1.00 Sqm 311.85 One Square 312.00
bitumen of grade VG -10 of approved quality using 1.8 Metre
kg of bitumen per sqm with 1.5 cum of stone chippings
13.2 mm nominal size per 100 sqm of road surface for
first coat and 1.1 kg. of bitumen per sqm with 1.00 cu.
metre of stone chippings 11.2 mm nominal size per 100
sqm of road surface for second coat, including
consolidation of each coat separately with road roller of
6 to 8 tonne capacity etc. complete.

DSR - 2023 IN MS EXCEL Page 139 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.27 Surface dressing on old surface with hot bitumen of 1.00 Sqm 175.10 One Square 175.00
grade VG - 10 of approved quality using 1.95 kg of Metre
bitumen per sqm. with 1.50 cum of stone chippings
11.2 mm nominal size per 100 sqm of road surface
including consolidation with road roller of 6 to 8 tonne
capacity, etc. complete.

16.28 Surface dressing one coat on new surface with bitumen

of specified grade at a rate of 1.95 kg/sqm. of surface
area with 1.5 cum. of stone chippings 13.2mm nominal
size per 100 sqm. of road surface including
consolidation with road roller of 6 to 8 tonne capacity ,
etc. complete :

16.28.1 Using bitumen emulsion (minimum 50% bitumen 1.00 Sqm 198.45 One Square 198.00
content - RS grade conforming to IS : 8887). Metre
16.29 Surface dressing one coat on old surface with bitumen
of specified grade at the rate of 1.22 kg/ sqm of surface
area with 1.10 cum of stone chippings 11.2 mm nominal
size per 100 sqm. of road surface including
consolidation with road roller of 6 to 8 tonne capacity
etc. complete :

16.29.1 Using bitumen emulsion (minimum 50% bitumen 1.00 Sqm 125.30 One Square 125.00
content - RS grade conforming to IS : 8887). Metre
16.30 Providing and applying tack coat using hot straight run
bitumen of grade VG - 10 including heating the
bitumen, spraying the bitumen with mechanically
operated spray unit fitted on bitumen boiler, cleaning
and preparing the existing road surface as per
specifications :

16.30.1 On W.B.M. @ 0.75 Kg / sqm. 1.00 Sqm 60.50 One Square 61.00
Metre
16.30.2 On bituminous surface @ 0.50 Kg / sqm. 1.00 Sqm 48.20 One Square 48.00
Metre
16.31 Providing and applying tack coat using bitumen
emulsion conforming to IS: 8887, using emulsion
pressure distributer including preparing the surface &
cleaning with mechanical broom.

16.31.1 With rapid setting bitumen emulsion.

16.31.1.1 On W.B.M / W.M.M. @ 0.4kg/sqm. 1.00 Sqm 13.45 One Square 13.00
Metre
16.31.1.2 On bituminous surface @ 0.25kg/sqm. 1.00 Sqm 9.20 One Square 9.00
Metre
16.31.2 With medium setting bitumen emulsion.
16.31.2.1 On W.B.M / W.M.M. @ 0.4kg/sqm. 1.00 Sqm 21.20 One Square 21.00
Metre
16.31.2.2 On bituminous surface @ 0.25kg/sqm. 1.00 Sqm 14.05 One Square 14.00
Metre
16.32 2 cm premix carpet surfacing with 1.8 cum and 0.90
cum of stone chippings of 13.2 mm size and 11.2 mm
size respectively per 100 sqm and 52 kg and 56 kg of
hot bitumen per cum of stone chippings of 13.2 mm
and 11.2 mm size respectively, including a tack coat
with hot straight run bitumen, including consolidation
with road roller of 6 to 9 tonne capacity etc. complete
(tack coat to be paid for separately).

16.32.1 With paving Asphalt grade VG - 10 heated and then 1.00 Sqm 234.05 One Square 234.00
mixed with solvent at the rate of 70 grams per kg of Metre
asphalt.

DSR - 2023 IN MS EXCEL Page 140 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.32.2 With paving Asphalt grade VG - 30 with no solvent 1.00 Sqm 245.15 One Square 245.00
Metre
16.32.3 With Refinery Modified Bitumen CRMB 55 conforming 1.00 Sqm 233.15 One Square 233.00
to IRC: SP: 53. Metre
16.33 2.5 cm premix carpet surfacing with 2.25 cum and 1.12
cum of stone chippings of 13.2 mm and 11.2 mm size
respectively per 100 sqm and 52 kg and 56 kg of hot
bitumen per cum of stone chippings of 13.2 mm and
11.2 mm size respectively, including a tack coat with
hot straight run bitumen, including consolidation with
road roller of 6 to 9 tonne capacity etc. complete (tack
coat to be paid for separately).

16.33.1 With paving Asphalt grade VG - 10 heated and then 1.00 Sqm 281.00 One Square 281.00
mixed with solvent at the rate of 70 grams per kg of Metre
asphalt.
16.33.2 With paving Asphalt grade VG - 30 with no solvent 1.00 Sqm 294.95 One Square 295.00
Metre
16.33.3 With Refinery Modified Bitumen CRMB 55 conforming 1.00 Sqm 279.90 One Square 280.00
to IRC: SP: 53. Metre
16.34 2 cm premix carpet surfacing with 2.4 cum of stone 1.00 Sqm 208.90 One Square 209.00
chippings 11.2 mm nominal size per 100 sqm and Metre
bitumen emulsion (medium setting min. 65% bitumen
content) complying with IS : 8887, using 96 kg per cum
of chippings, including consolidation with road roller of
6 to 9 tonne capacity etc. complete.

16.35 2.5 cm premix carpet surfacing with 3 cum of stone 1.00 Sqm 252.15 One Square 252.00
chippings 10 mm nominal size per 100 sqm and Metre
bitumen emulsion (medium setting min. 65% bitumen
contents) complying with IS : 8887, using 96 kg per cum
of chippings of road surface, including consolidation
with road roller etc complete.

16.36 Providing and laying Bitumen Penetration Macadam

with hard stone aggregate of quality, size and grading
as specified, with bitumen of suitable penetration
grade, including required key aggregate as specified,
spreading coarse aggregate with the help of self
propelled/ tipper tail mounted aggregate spreader and
applying bitumen by a pressure distributor and then
spreading key aggregate with the help of aggregate
spreader complete, including consolidation with road
roller of minimum 8 to 10 tonne capacity to achieve
specified values of compaction and surface accuracy :

16.36.1 For 50mm compacted thickness using coarse aggregate 1.00 Sqm 505.65 One Square 506.00
of size 50-20 mm graded @ 0.60 cum per 10 sqm key Metre
aggregate of size 12.5 mm graded @ 0.15 cum per 10
sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10
sqm.

16.36.2 For 75 mm compacted thickness in two layers using 1.00 Sqm 744.15 One Square 744.00
stone aggregate of size 63-41 mm graded @ 0.90 cum Metre
per 10 sqm key aggregate of size 20.0 mm graded @
0.18 cum per 10 sqm. With paving asphalt grade VG -
10 @ 68 kg 10 sqm.

DSR - 2023 IN MS EXCEL Page 141 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.37 Providing and laying bitumen mastic wearing course (as
per specifications) with industrial bitumen of grade
85/25 conforming to IS : 702, prepared by using mastic
cooker and laid to required level and slope, including
providing antiskid surface with bitumen precoated fine
grained hard stone chipping of approved size at the rate
of 0.005 cum per 10 sqm and at approximate spacing of
10 cm centre to centre in both directions, pressed into
surface protruding 1 mm to 4 mm over mastic surface,
including cleaning the surface, removal of debris etc. all
complete. (Considering bitumen using 10.2% as per
MORTH specification).

16.37.1 25mm thick. 1.00 Sqm 854.15 One Square 854.00

Metre
16.37.2 40 mm thick 1.00 Sqm 1365.50 One Square 1366.00
Metre
16.38 2.5 cm thick bitumastic sheet with hot bitumen of
approved quality, using stone chippings (60% with 12.5
mm nominal size and 40% with 10 mm nominal size) @
1.65 cum per 100 sqm and coarse sand @ 1.65 cum per
100 sqm of road surface and with bitumen @ 56
kg/cum of stone chippings and @ 128 kg/cum of sand
over a tack coat with hot straight run bitumen,
including consolidation with road roller of 8 to 10 tonne
etc. complete. (tack coat to be paid separately) :

16.38.1 With paving Asphalt grade VG - 10 heated and then 1.00 Sqm 353.65 One Square 354.00
mixed with solvent at the rate of 70 grams per kg of Metre
asphalt.
16.38.2 With paving Asphalt grade VG - 30. 1.00 Sqm 377.05 One Square 377.00
Metre
16.38.3 With Refinery Modified Bitumen CRMB 55 conforming 1.00 Sqm 351.80 One Square 352.00
to IRC: SP : 53. Metre
16.39 4 cm thick bitumastic sheet with hot bitumen of
approved quality, using stone chippings (60% with 12.5
mm nominal size and 40% with 10 mm nominal size) @
2.60 cum per 100 sqm and coarse sand @ 2.60 cum per
100 sqm of road surface and with bitumen @ 56
kg/cum of stone chippings and @ 128 kg/cum of sand
over a tack coat with hot straight run bitumen,
including consolidation with road roller of 8 to 10 tonne
etc. complete. (tack coat to be paid separately) :

16.39.1 With paving Asphalt grade VG - 10 heated and then 1.00 Sqm 531.60 One Square 532.00
mixed with solvent at the rate of 70 grams per kg of Metre
asphalt.
16.39.2 With paving asphalt grade VG - 30 with no solvent 1.00 Sqm 568.60 One Square 569.00
Metre
16.39.3 With Refinery Modified Bitumen CRMB 55 conforming 1.00 Sqm 528.65 One Square 529.00
to IRC: SP : 53. Metre
16.40 Providing and laying seal coat of premixed fine 1.00 Sqm 88.55 One Square 89.00
aggregate ( passing 2.36 mm and retained on 180 Metre
micron sieve) with bitumen using 128 kg of bitumen of
grade VG - 10 bitumen per cum of fine aggregate and
0.60 cum of fine aggregate per 100 sqm of road surface,
including rolling and finishing with road roller all
complete.

DSR - 2023 IN MS EXCEL Page 142 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.41 Providing and laying seal coat over prepared surface of 1.00 Sqm 130.85 One Square 131.00
road with bitumen heated in bitumen boiler fitted with Metre
the spray set spraying using 98 kg of bitumen of grade
VG - 10 and blinding surface with 0.90 cum of stone
aggregate of 6.7 mm size (Passing 11.2 mm sieve and
retained on 2.36 mm sieve) per 100 sqm of road
surface, including rolling and finishing with power road
roller all complete. Note: Seal coat items to be operated
only with the prior approval of chief Engineer
concerned.

16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 1.00 Cum 7993.80 One Cubic 7994.00
graded stone aggregate 40 mm nominal size) in Metre
pavements, laid to required slope and camber in panels
as required including consolidation finishing and
tamping complete.

16.43 Providing and laying design mix cement concrete of M-

30 grade, in roads/ taxi tracks/ runways, using cement
content as per design mix, using coarse sand and
graded stone aggregate of 40 mm nominal size in
appropriate proportions as per approved & specified
design criteria, providing dowel bars with sleeve/ tie
bars wherever required, laying at site, spreading and
compacting mechanically by using needle and surface
vibrators, levelling to required slope/ camber,finishing
with required texture, including steel form work with
sturdy M.S. channel sections, curing, making provision
for contraction/ expansion, construction & longitudinal
joints (10 mm wide x 50 mm deep) by groove cutting
machine, providing and filling joints with approved joint
filler and sealants, complete all as per direction of
Engineer-in-charge (Item of joint fillers, sealants, dowel
bars with sleeve/ tie bars to be paid separately).

Note: Cement content considered in M-30 is @

340Kg/Cum. Excess/Less cement used as per design mix
is payable, recoverable separately.
16.43.1 Cement concrete prepared with batch mixing machine. 1.00 Cum 10529.35 One Cubic 10529.00
Metre
16.43.2 Cement concrete manufactured in automatic batching 1.00 Cum 11098.45 One Cubic 11098.00
plant (RMC plant) i/c transportation to site in transit Metre
mixer.
16.44 Extra for providing and mixing hardening compound of 1.00 Ltr 55.50 One Litre 56.00
approved quality as per manufacturer's specification in
cement concrete.
16.45 Providing and fixing pre-moulded joint filler in 1.00 units 5.30 Per cm depth 5.00
expansion joints of RCC roads / CC pavements after per cm width
making the joints dust free with high pressure air jet per m length
cleaners, all complete as per direction of the Engineer-
in-Charge. (Pre-moulded joint fillers shall be made of
bitumen hot sealing compound impregnated fibre
board having impregnation more than 35%, conforming
to IS:1838 for fibre board and IS: 1834 for hot sealing
bitumen compound grade A.)

16.46 Providing and filling in position rubberized bitumen hot

sealing compound for sealing of expansion joints in
roads / pavements all complete as per direction of the
Engineer-in-Charge.

DSR - 2023 IN MS EXCEL Page 143 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.46.1 Using grade 'A' sealing compound conforming to IS: 1.00 units 8.65 Per cm depth 9.00
1834. per cm width
per m length

16.47 Painting runway/taxi track/apron marking with

adequate nos of coats to give uniform finish with road
marking paint of superior make as approved by the
Engineer-in-charge, i/c cleaning the surface of all dirt,
scales, oil, grease and other foreign material etc. and
lining outcomplete.

16.47.1 New work (Two or more coats) 1.00 Sqm 188.20 One Square 188.00
Metre
16.47.2 Old work (One or more coats) 1.00 Sqm 120.80 One Square 121.00
Metre
16.48 Painting road surface marking with adequate nos of
coats to give uniform finish with ready mixed road
marking paint conforming to IS : 164, on bituminous
surface in white/yellow shade, including cleaning the
surface of all dirt, scales, oil, grease and foreign
material etc. complete.

16.48.1 New work (Two or more coats). 1.00 Sqm 288.90 One Square 289.00
Metre
16.48.2 Old work (One or more coats) 1.00 Sqm 189.85 One Square 190.00
Metre
16.49 Making bell mouth opening/ entrance of size 1.00 No. 3050.40 Each 3050.00
100x50x50 cm for drainage pipe under footpath,
including providing cement concrete 1:3:6 (1 cement : 3
coarse sand : 6 graded stone aggregate 20 mm nominal
size) for shape of bell mouth, including plastering
providing and fixing precast R.C.C./ S.F.R.C. slab
including plastering with cement mortar 1:3 (1 cement :
3 fine sand) of 6 mm thickness on exposed surface of
the slab & bell mouth including centring, shuttering &
neat cement punning inside the bell mouth etc. all
complete.

16.50 Providing and fixing Glow studs of size 100x20 mm 1.00 No. 206.30 Each 206.00
made of heavy duty body shall be moulded ASA (Acrylic
styrene Acryloretrite ) or HIP (High impact polystyrene)
or ABS having electronically welded micro- prismatic
lens with abrasion resistant coating as approved by
Engineer in charge. The glow stud shall support a load
of 13635 kg tested in accordance with ASTM D4280.
The slope of retro- reflective surface shall be 35 (+/-5)
degress to base .The reflective panels on both sides
with at least 12 cm of reflective area up each side. The
luminance intensity should be as per the specification
and shall be tested as described in ASTM I: 809 as
recommended in BS: 873 part 4 : 1973. The studs shall
be fixed to the Road surface using the adhesive
conforming to IS, as per procedure recommended by
the manufacturer complete and as per direction of
Engineer-in-charge.

16.51 Preparation of sub-base road pavement with

commercial dry lime (slaked), fly ash stabilised soil with
a mix of 3% lime, 12% fly ash and 85% local suitable soil
by weight, so as to achieve minimum field C.B.R. of 20,
including mixing, rolling with road roller curing etc. all
complete.

DSR - 2023 IN MS EXCEL Page 144 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.51.1 Minimum thickness 15 cm. 1.00 Sqm 1514.40 One Cubic 1514.00
Metre
16.52 Providing and fixing precast lime fly ash concrete blocks 1.00 Sqm 13719.05 One Cubic 13719.00
1:2:3:6 (1 lime: 2 fly ash : 3 coarse sand : 6 graded stone Metre
aggregate 20 mm nominal size), including finishing with
10mm thick cement mortar 1:3 (1 cement : 3 coarse
sand) in foot paths, including preparation of sub grade
with a hand rammer, laying 10 mm thick leveling course
of fine sand (jamuna sand) and filling the joints with
fine sand.

16.53 Providing and fixing concertina coil fencing with 1.00 m 375.80 One Running 376.00
punched tape concertina coil 600 mm dia 10 metre Metre
openable length ( total length 90 m), having 50 nos
rounds per 6 metre length, upto 3 m height of wall with
existing angle iron 'Y' shaped placed 2.4m or 3.00 m
apart and with 9 horizontal R.B.T. reinforced barbed
wire, stud tied with G.I. staples and G.I. clips to retain
horizontal, including necessary bolts or G.I. barbed wire
tied to angle iron, all complete as per direction of
Engineer-in-charge, with reinforced barbed
tape(R.B.T.) / Spring core (2.5mm thick) wire of high
tensile strength of 165 kg/ sq.mm with tape (0.52 mm
thick) and weight 43.478 gm/ metre (cost of M.S. angle,
C.C. blocks shall be paid separately)

16.54 Providing and laying Dense Graded Bituminous

Macadam using crushed stone aggregates of specified
grading, premixed with bituminous binder and filler,
transporting the hot mix to work site by tippers, laying
with paver finisher equiped with electronic sensor to
the required grade, level and alignment and rolling with
smooth wheeled, vibratory and tandem rollers as per
specifications to achieve the desired compaction and
density, complete as per specificatons and directions of
Engineer-in-Charge.

16.54.1 50 to 100 mm average compacted thickness with 1.00 Sqm 11129.55 One Cubic 11130.00
bitumen of grade VG-30 @ 5% (percentage by weight of Metre
total mix) and lime filler @ 2% (percentage by weight of
Aggregate) prepared in Batch Type Hot Mix Plant of
100-120 TPH capacity.

16.54.2 50 to 100 mm average compacted thickness with 1.00 Sqm 11032.20 One Cubic 11032.00
bitumen of grade VG-30 @ 5% (percentage by weight of Metre
total mix) and lime filler @ 2% (percentage by weight of
Aggregate) prepared in Drum Type Hot Mix Plant of 60-
90 TPH capacity.

16.55 Providing and laying bituminous macadam using

crushed stone aggregate of specified grading premixed
with bituminous binder, transported to site by tippers,
laid over a previously prepared surface with paver
finisher equipped with electronic sensor to the required
grade, level and alignment and rolling with smooth
wheeled, vibratory and tandem rollers as per
specifications to achieve the desired compaction and
density, complete as per specifications and directions of
Engineer-in-Charge.

16.55.1 50 to 100 mm average compacted thickness with 1.00 Sqm 8505.65 One Cubic 8506.00
bitumen of grade VG-30 @ 3.50% (percentage by Metre
weight of total mix) prepared in Batch Type Hot Mix
Plant of 100-120 TPH capacity.

DSR - 2023 IN MS EXCEL Page 145 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.55.2 50 to 100 mm average compacted thickness with 1.00 Sqm 8413.00 One Cubic 8413.00
bitumen of grade VG-30 @ 3.50% (percentage by Metre
weight of total mix) prepared in Drum type Hot Mix
plant of 60-90 TPH capacity.

16.56 Providing and laying semi-dense Bituminous concrete

using crushed stone aggregates of specified grading,
premixed with bituminous binder and filler,
transporting the hot mix to work site by tippers, laying
with paver finisher equipped with electronic sensor to
the required grade, level and alignment and rolling with
smooth wheeled, vibratory and tandem rollers to
achieve the desired compaction and density as per
specification, complete and as per directions of
Engineer-in-Charge.

16.56.1 25mm compacted thickness with bitumen of grade VG- 1.00 Sqm 277.70 One Square 278.00
30 @ 5% (percentage by weight of total mix) and lime Metre
filler @ 2% (percentage by weight of Aggregate)
prepared in Batch Type Hot Mix Plant of 100-120 TPH
capacity.

16.56.2 25mm compacted thickness with bitumen of grade VG- 1.00 Sqm 275.30 One Square 275.00
30 @ 5% (percentage by weight of total mix) and lime Metre
filler @ 2% (percentage by weight of Aggregate)
prepared in Drum Type Hot Mix Plant of 60-90 TPH
capacity.

16.57 Providing and laying Bituminous concrete using crushed

stone aggregates of specified grading premixed with
bituminous binder and filler, transporting the hot mix to
work site by tippers, laying with paver finisher equipped
with electronic sensor to the required grade, level and
alignment and rolling with smooth wheeled, vibratory
and tandem rollers to achieve the desired compaction
and density as per specification, complete and as per
directions of Engineer-in-Charge.

16.57.1 40/50mm compacted thickness with bitumen of grade 1.00 Sqm 12126.20 One Cubic 12126.00
VG-30 @ 5.5% (percentage by weight of total mix) and Metre
lime filler @ 3% (percentage by weight of Aggregate)
prepared in Batch type Hot Mix Plant of 100-120 TPH
capacity.

16.57.2 40/50mm compacted thickness with bitumen of grade 1.00 Sqm 12708.75 One Cubic 12709.00
VG-30 @ 5.5% (percentage by weight of total mix) and Metre
lime filler @ 3% (percentage by weight of Aggregate)
and waste plastic additive @ 8% (percentage by weight
of bitumen) prepared in Batch type Hot Mix Plant of
100-120 TPH capacity.

16.57.3 40/50 mm compacted thickness with bitumen of grade 1.00 Sqm 11204.10 One Cubic 11204.00
PMB-40 @ 5.5% (percentage by weight of total mix) Metre
and lime filler @ 3% (percentage by weight of
Aggregate) prepared in Batch Type Hot Mix Plant of
100-120 TPH capacity.

16.57.4 40/50 mm compacted thickness with bitumen of grade 1.00 Sqm 10660.30 One Cubic 10660.00
CRMB-60 @ 5.5% (percentage by weight of total mix) Metre
and lime filler @ 3% (percentage by weight of
Aggregate) prepared in Batch Type Hot Mix Plant of
100-120 TPH capacity.

DSR - 2023 IN MS EXCEL Page 146 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.57.5 40/50 mm compacted thickness with bitumen of grade 1.00 Sqm 12026.80 One Cubic 12027.00
VG-30 @ 5.5% (percentage by weight of total mix) and Metre
lime filler @ 3% (percentage by weight of Aggregate)
prepared in drum Type Hot Mix Plant of 60-90 TPH
capacity.

16.57.6 40/50 mm compacted thickness with bitumen of grade 1.00 Sqm 12609.30 One Cubic 12609.00
VG-30 @ 5.5% (percentage by weight of total mix) and Metre
lime filler @ 3% (percentage by weight of Aggregate)
and waste plastic additive @ 8% (percentage by weight
of bitumen) prepared in drum Type Hot Mix Plant of 60-
90 TPH capacity.

16.57.7 40/50 mm compacted thickness with bitumen of grade 1.00 Sqm 11104.65 One Cubic 11105.00
PMB-40 @ 5.5% (percentage by weight of total mix) Metre
and lime filler @ 3% (percentage by weight of
Aggregate) prepared in drum Type Hot Mix Plant of 60-
90 TPH capacity

16.57.8 40/50 mm compacted thickness with bitumen of grade 1.00 Sqm 10560.85 One Cubic 10561.00
CRMB-60 @ 5.5% (percentage by weight of total mix) Metre
and lime filler @ 3% (percentage by weight of
Aggregate) prepared in Drum Type Hot Mix Plant of 60-
90 TPH capacity.

16.59 Manufacturing, supplying and fixing retro reflective sign

boards made up of 2 mm thick aluminium sheet, face to
be fully covered with high intensity encapsulated type
heat activated retro reflective sheeting conforming to
type - IV of ASTM-D 4956-01 in blue and silver white or
other colour combination including subject matter,
message (bi-lingual), symbols and borders etc. as per
IRC ; 67:2001, pasted on substrate by an adhesive
backing which shall be activated by applying heat and
pressure conforming to class -2 of ASTM-D-4956-01 and
fixing the same with suitable sized aluminium alloy
rivets @ 20 cm c/c to back support frame of M.S. angle
iron of size 25x25x3 mm along with theft resistant
measures,

mounted and fixed with 2 Nos. M.S. angles of size

35x35x5 mm to a vertical post made up to M.S. Tee
section ISMT 50x50x6 mm welded with base plate of
size 100x100x5 mm at the bottom end and including
making holes in pipes, angles flats, providing & fixing
M.S. message plate of required size, steel work to be
painted with two or more coats of synthetic enamel
paint of required shade and of approved brand &
manufacture over priming coat of zinc chromate yellow
primer (vertical MS-Tee support to be painted in black
and white colours).

Backside of aluminium sheet to be painted with two or

more coats of epoxy paint over and including
appropriate priming coat including all leads and lifts etc.
complete as per drawing, specification and direction of
Engineer-in-charge.

16.59.1 Mandatory/ Regulatory sign boards of 900 mm 1.00 No. 7183.35 Each 7183.00
diametre with support length of 3750 mm
16.59.2 Cautionary /warning sign boards of equilateral 1.00 No. 5559.75 Each 5560.00
triangular shape having each side of 900 mm with
support length of 3650 mm

DSR - 2023 IN MS EXCEL Page 147 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.60 Manufacturing, supplying and fixing retro reflective
overhead signage boards made up of 2 mm thick
aluminium sheet, face to be fully covered with high
intensity and encapsulated lens type heat activated
retro reflective sheeting conforming to type - III of
ASTM-D-4956-01 as approved by Engineer-in-charge,
letters, borders etc. as per IRC : 67-2001 in silver white
with blue colour back ground and with high intensity
grade, pasted on substrate by pressure sensitive
adhesive backing which shall be activated by applying
pressure conforming to class II of ASTM-D-4956-01 and
fixing the same to the plate of structural frame work by
means of suitable sized aluminium alloys, rivets or bolts
& nuts @ 300 mm centre to centre all along the
periphery as well as in two vertical rows along with
theft resistant measures, including the cost of painting
with two or more coats of epoxy paint in grey colour on
the back side of aluminium sheet including appropriate
priming coat.

The rate includes the cost of rounding off the corners,

lowering down the structural frame work from the
gantry, fixing and erecting the same in position all
complete as per drawings, specification and direction of
the engineer-in charge.(Structural frame work including
M.S. plate to be provided separately. Rectangular area
of the sheet only shall be measured for payment).

16.60.1 Overhead informatory road signage 1.00 Sqm 5879.90 One Square 5880.00
Metre
16.61 Providing Retro-reflective regulatory sign board of size 1.00 No. 8154.35 Each 8154.00
900 mm dia meter made out of 2 mm thick aluminium
sheet, face to be fully covered with high intensity
encapsulated lens type retro-reflective sheeting as
approved by Engineer-in-charge . Letter, symbols,
borders etc. will be as per IRC - 67 with required colour
scheme on the boards and with the high intensity grade
A. The aluminium sheet to be riveted to M.S. frame of
angle iron of size 40x40x4 mm. The boards will be fixed
to 1 No. 50x50 mm square post made of M.S. angle
50x50x4 mm, 4 m long welded to the frame with
adequate anti-theft arrangement .Sheet work to be
painted with two or more coats of synthetic enamel
paint over an under coat (primer) and back side of
aluminium sheet to be painted with two or more coats
of epoxy paint including appropriate priming coat
complete in all respects as per direction of Engineer-in-
charge.

DSR - 2023 IN MS EXCEL Page 148 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.62 Providing and applying 2.5 mm thick road marking strips 1.00 Sqm 747.80 One Square 748.00
(retro-reflective) of specified shade/ colour using hot Metre
thermoplastic material by fully/ semi automatic
thermoplastic paint applicator machine fitted with
profile shoe, glass beads dispenser, propane tank
heater and profile shoe heater, driven by experienced
operator on road surface including cost of material,
labour, T&P, cleaning the road surface of all dirt, seals,
oil, grease and foreign material etc. complete as per
direction of Engineer-in-charge and accordance with
applicable specifications.

16.63 Providing, laying and making kerb channel 30 cm wide 1.00 Sqm 558.30 One Square 558.00
and 50 mm thick with cement concrete 1:3:6 (1 cement: Metre
3 coarse sand:6 graded stone aggregate 20 mm nominal
size) over 75mm bed of dry brick ballast 40 mm nominal
size, well rammed and consolidated and grouted with
fine sand, including finishing the top smooth etc.
complete and as per direction of Engineer-in-charge.

16.64 Providing and laying 75 mm thick compacted bed of dry 1.00 Sqm 199.35 One Square 199.00
brick aggregate of 40 mm thick nominal size including Metre
spreading, well ramming, consolidating and grouting
with jamuna sand, including finishing smooth etc.
complete as per direction of Engineer-in-charge.

16.65 Providing and fixing post delineators made of ABS 1.00 No. 904.20 Each 904.00
round body fitted with 2 nos 100 mm dia high reflective
reflectors and mounted on MS pipe of 65 mm dia duly
powder coated anti-rust and anti theft steel to be
installed as per direction of Engineer-in-charge.

16.66 Excavating holes upto 0.10 cum, including getting out

the excavated soil, then returning the soil as deported
in layers not exceeding 20 cm in depth, including
consolidating and deposited layer by ramming watering
etc., disposing of surplus excavated soil as directed with
in a lead of 50 mm and lift upto 1.5 m.

16.66.1 All kind of soil. 1.00 No. 27.50 Each 28.00

16.67 Providing and fixing at or near ground level factory 1.00 Sqm 1600.55 One Square 1601.00
made RCC pavement slab of M-30 grade of size Metre
450x450x50 mm, including reinforcement with 6 mm
dia M.S. bars 4 nos on each side, including setting in
position in footpath to the required level and line over a
bed of 20 mm average thick cement mortar 1:5 (1
cement : 5 coarse sand), having joint thickness not
more than 5mm except on curve, including filling of
joints with same cement mortar and making grooves
etc. complete as per direction of Engineer-in-charge.

16.68 Providing and laying 60mm thick factory made cement 1.00 Sqm 972.00 One Square 972.00
concrete interlocking paver block of M -30 grade made Metre
by block making machine with strong vibratory
compaction, of approved size, design & shape, laid in
required colour and pattern over and including 50mm
thick compacted bed of coarse sand, filling the joints
with fine sand etc. all complete as per the direction of
Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 149 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.69 Providing and laying at or near ground level factory 1.00 Sqm 10117.60 One Cubic 10118.00
made kerb stone of M-25 grade cement concrete in Metre
position to the required line, level and curvature,
jointed with cement mortar 1:3 (1 cement: 3 coarse
sand), including making joints with or without grooves
(thickness of joints except at sharp curve shall not to
more than 5mm), including making drainage opening
wherever required complete etc. as per direction of
Engineer-in-charge (length of finished kerb edging shall
be measured for payment). (Precast C.C. kerb stone
shall be approved by Engineer-in-charge).

16.70 Providing and fixing G.I. chain link fabric fencing of

required width in mesh size 50x50 mm including
strengthening with 2 mm dia wire or nuts, bolts and
washers as required complete as per the direction of
Engineer-in-charge.

16.70.1 Made of G.I. wire of dia 4 mm 1.00 Sqm 1017.80 One Square 1018.00
Metre
16.70.2 Made of G.I. wire of dia. 4 mm, PVC coated to achieve 1.00 Sqm 1067.10 One Square 1067.00
outer dia not less than 5 mm in required colour and Metre
shade
16.71 Providing and fixing G.I. chain link fabric fencing of 1.00 Sqm 1149.25 One Square 1149.00
required width in mesh size 25x25 mm made of G.I. Metre
wire of dia 3 mm including strengthening with 2 mm dia
wire or nuts, bolts and washers as required complete as
per the direction of Engineer-in-charge.

16.72 Supplying and stacking of hard stone (for stone 1.00 Sqm 995.85 One Cubic 996.00
pitching) 22.5 cm thick at site. Metre
16.73 Dry stone pitching 22.5 cm thick laid in courses and 1.00 Sqm 659.05 One Square 659.00
required profile with hammer dressed stones having no Metre
side less than 15 cm, with minimum depth of 20 cm
including preparing the bedding surface etc. all
complete. (Payment for Stone to be made separately).

16.74 75 mm thick back filling for pitching including supplying

of required materials and consolidation etc. complete
with :
16.74.1 Moorum 1.00 Sqm 76.30 One Square 76.00
Metre
16.74.2 Stone aggregate 20mm nominal size 1.00 Sqm 175.00 One Square 175.00
Metre
16.74.3 Stone aggregate 40mm nominal size 1.00 Sqm 172.35 One Square 172.00
Metre
16.75 Providing and laying C.C. pavement of mix M-25 with 1.00 Sqm 9823.80 One Cubic 9824.00
ready mixed concrete from batching plant. The ready Metre
mixed concrete shall be laid and finished with screed
board vibrator , vacuum dewatering process and finally
finished by floating, brooming with wire brush etc.
complete as per specifications and directions of
Engineer-in charge. (The panel shuttering work shall be
paid for separately). (Note:- Cement content considered
in this item is @ 330 kg/cum. Excess/less cement used
as per design mix is payable/ recoverable separately).

16.76 Deduct for using of M-20 grade concrete instead of M- 1.00 Sqm -203.80 One Cubic -204.00
25 grade concrete in C.C. pavement. Metre

DSR - 2023 IN MS EXCEL Page 150 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.77 Scarifying the existing bituminous road surface to a 1.00 Sqm 7.00 One Square 7.00
depth of 50 mm and disposal of scarified material Metre
within all lifts and lead upto 1km (by mechanical
means).

16.78 Construction of granular sub-base by providing close

graded Material conforming to specifications, mixing in
a mechanical mix plant at OMC, carriage of mixed
material by tippers to work site, for all leads & lifts,
spreading in uniform layers of specified thickness with
motor grader on prepared surface and compacting with
vibratory power roller to achieve the desired density,
complete as per specifications and directions of
Engineer-in-Charge.

16.78.1 With material conforming to Grade-I (size range 75 mm 1.00 Sqm 2784.00 One Cubic 2784.00
to 0.075 mm) having CBR Value-30 Metre
16.78.2 With material conforming to Grade-II (size range 53 mm 1.00 Sqm 2924.85 One Cubic 2925.00
to 0.075 mm) having CBR Value-25 Metre
16.78.3 With material conforming to Grade-III(size range 26.5 1.00 Sqm 2808.55 One Cubic 2809.00
mm to 0.075 mm) having CBR Value-20 Metre
16.79 Providing, laying, spreading and compacting graded 1.00 Sqm 2914.30 One Cubic 2914.00
stone aggregate (size range 53 mm to 0.075 mm ) to Metre
wet mix macadam (WMM) specification including
premixing the material with water at OMC in for all
leads & lifts, laying in uniform layers with mechanical
paver finisher in sub- base / base course on well
prepared surface and compacting with vibratory roller
of 8 to 10 tonne capacity to achieve the desired density,
complete as per specifications and directions of
Engineer-in-Charge.

16.80 Construction of dry lean cement concrete sub base over 1.00 Sqm 4148.65 One Cubic 4149.00
a prepared sub-grade with coarse and fine aggregate Metre
conforming to IS:383, the size of coarse aggregate not
exceeding 25 mm, aggregate cement ratio not to
exceed 15:1, aggregate gradation after blending to be
as per specifications, cement content not to be less
than 150 Kg/cum, optimum moisture content to be
determined during trial length construction, concrete
strength not to be less than 10 Mpa at 7 days, mixed in
a batching plant, transported to site, for all leads & lifts,
laid with a mechanical paver, compacting with 8-10
tonne vibratory roller, finishing and curing etc.
complete as per direction of Engineer-in-charge.

16.81 Providing and erecting 2.00 metre high temporary

barricading at site; each panel of size 2.50m x 2.00m
made of 40x40x6 mm angle iron or 50x50x3 mm hollow
MS tube posts/ horizontal members/ bracings covered
with 1.63 mm thick MS sheet. The sheet shall be fixed
with 30x5 mm MS flat by suitable welding / riveting.
The panels shall be made so that gap of 50 cm above
the ground is available making over all height as 2.50m.
MS channel ISLC 75 @ 5.70 kg/m, 50 cm long shall be
provided at the bottom having oval shaped holes of size
50x25 mm at both ends with 50 cm long MS angle
40x40x6 mm bracing.

Suitable arrangement shall be made to fix the

barricading to avoid from overturning by providing 250
mm long expansion fasteners at both ends.

DSR - 2023 IN MS EXCEL Page 151 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
The work shall be executed as per drawing/ direction of
Engineer-in-Charge which includes writing and painting,
arrangement for traffic diversion such as traffic signals
during construction at site for day and night, glow
lamps, reflective signs, marking, flags, caution tape as
directed by the Engineer-in- Charge. The barricading
provided shall be retained in position at site
continuously i/c shifting of barricading from one
location to another location as many times as required
during the execution of the entire work till its
completion. Rate include its maintenance for damages,
painting, all incidentals, labour, materials, equipments
and works required to execute the job. The barricading
shall not be removed without prior approval of
Engineer-in-Charge.

(Note :- One time payment shall be made for providing 1.00 Sqm 3439.50 One Running 3440.00
barricading from start of work till completion of work Metre
i/c shifting. The barricading provided shall remain to be
the property of the contractor on completion of the
work).

16.82 Taking out existing kerb stones of all types from 1.00 m 39.35 One Running 39.00
footpath/ central verge, including removal of mortar Metre
etc., disposal of unserviceable material to the dumping
ground, for which payment shall be made separately
and stacking of serviceable material within 50 metre
lead as per direction of Engineer-in-Charge.

16.83 Taking out existing CC interlocking paver blocks from 1.00 Sqm 131.75 One Square 132.00
footpath/ central verge, including removal of rubbish Metre
etc., disposal of unserviceable material to the dumping
ground, for which payment shall be made separately
and stacking of serviceable material within 50 metre
lead as per direction of Engineer-in-Charge.

16.84 Laying old cement concrete interlocking paver blocks of 1.00 Sqm 402.95 One Square 403.00
any design/ shape laid in required line, level, curvature, Metre
colour and pattern over and including 50 mm thick
compacted bed of coarse sand, filling the joints with
fine sand etc. all complete as per the direction of
Engineer in-charge. (Old CC paver blocks shall be
supplied by the department free of cost).

16.85 Laying at or near ground level old kerb stones of all 1.00 m 109.45 One Metre 109.00
types in position to the required line, level and
curvature, jointed with cement mortar 1:3 (1 cement : 3
coarse sand), including making joints with or without
grooves (thickness of joints, except at sharp curve, shall
not be more than 5 mm), including making drainage
opening wherever required etc. complete as per
direction of Engineer -in-charge. (Length of finished
kerb edging shall be measured for payment). (Old kerb
stones shall be supplied by the department free of
cost).

DSR - 2023 IN MS EXCEL Page 152 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.86 Providing and laying gang saw cut 18 mm thick, mirror
polished pre-moulded and pre polished machine cut
granite stone of required size and shape of approved
shade, colour and texture in footpath, flooring in road
side plazas and similar locations, laid over 20mm thick
base of cement mortar 1:4 (1cement : 4 coarse sand)
including grouting the joints with white cement mixed
with matching pigment, epoxy touch ups etc. complete
as per direction of Engineer-in-Charge.

16.86.1 With granite stone of area less than 0.50 sqm. 1.00 Sqm 4746.20 One Square 4746.00
Metre
16.87 Providing and laying gang saw cut 30 mm thick, mirror
polished pre moulded and pre polished machine cut
granite stone of required size and shape of approved
shade, colour and texture in footpath, flooring in road
side plazas and similar locations, laid over 20mm thick
base of cement mortar 1:4 (1 cement : 4 coarse sand)
including grouting the joints with white cement mixed
with matching pigment, epoxy touch ups etc. complete
as per direction of Engineer-in-Charge.

16.87.1 With granite stone of colour black, cherry/ruby red of 1.00 Sqm 4950.90 One Square 4951.00
area less than 0.50 sqm Metre
16.87.2 With granite stone of all colour except black, 1.00 Sqm 5272.05 One Square 5272.00
cherry/ruby red of area less than 0.50 sqm Metre
16.88 Providing and laying matt finished vitrified tile of size 1.00 Sqm 2159.85 One Square 2160.00
100x100x16mm having water absorption less than 0.5% Metre
and conforming to IS: 15622 of approved make in all
colours and shades in out door floors such as footpath,
court yard multi models etc., laid on 20mm thick base
of cement mortar 1:4 (1cement : 4 coarse sand) in all
shapes &patterns including grouting the joints with
white cement mixed with matching pigments etc.
complete as per direction of Engineer-in-Charge

16.89 Providing and laying matt finished vitrified tile of size 1.00 Sqm 1455.65 One Square 1456.00
300x300x9.8mm having water absorption less than Metre
0.5% and conforming to IS: 15622 of approved make in
all colours and shades in outdoor floors such as
footpath, court yard, multi modals location etc., laid on
20mm thick base of cement mortar 1:4 (1 cement : 4
coarse sand) in all shapes & patterns including grouting
the joints with white cement mixed with matching
pigments etc. complete as per direction of Engineer-in-
Charge.

16.90 Providing and laying tactile tile (for vision impaired 1.00 Sqm 2017.60 One Square 2018.00
persons as per standards) of size 300x300x9.8mm Metre
having water absorption less than 0.5% and conforming
to IS: 15622, of approved make in all colours and
shades in outdoor floors such as footpath, court yard,
multi modals location etc., laid on 20mm thick base of
cement mortar 1:4 (1 cement : 4 coarse sand) in all
shapes & patterns including grouting the joints with
white cement mixed with matching pigments etc.
complete as per direction of Engineer-in-Charge.

DSR - 2023 IN MS EXCEL Page 153 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.91 Providing and laying factory made chamfered edge
Cement Concrete paver blocks In foot path, park &
lawns driveway or light & traffic parking etc. of required
strength, thickness & size/ shape, made by table
vibratory method using PU mould, laid in required
colour & pattern over 50mm thick compacted bed of
course sand, compacting and proper embedding/ laying
of inter locking paver blocks into the sand bedding layer
through vibratory compaction by using plate vibrator,
filling the joints with sand and cutting of paver blocks as
per required size and pattern, finishing and sweeping
extra sand, all complete as per manufacturer's
specifications & direction of Engineer in-Charge.

16.91.1 60mm thick Cement concrete paver block of M-35 1.00 Sqm 1045.65 One Square 1046.00
grade with approved colour, design & pattern Metre
16.91.2 80mm thick Cement concrete paver block of M-30 1.00 Sqm 1091.50 One Square 1092.00
grade with approved colour, design & pattern. Metre
16.92 Providing and fixing 10x10x7.50 cm Granite stone block 1.00 Sqm 2189.15 One Square 2189.00
hand cut and chisel dressed on top, for paving in floors, Metre
drains etc. laid over 20mm thick base mortar 1:4 (1
cement : 4 coarse sand) with joints 10mm wide filled
with same mortar including ruled pointing etc.
complete as per direction of engineer-in-charge.

16.93 Providing and placing in position 100 mm thick factory 1.00 Sqm 3081.95 One Square 3082.00
made machine batched & machine mixed Precast RCC Metre
Rectangular Covers on drains of footpath of various
sizes, of M-25 grade cement concrete for RCC work,
including cost of centering, shuttering, reinforcement of
8 mm dia TMT bars of Fe 500 grade @ maximum
100mm c/c on both ways , neat cement punning on
finished surface, properly encased on all edges with 1.6
mm thick , 100 mm wide MS sheet duly painted over
priming coat , reinforcement to be welded at edges
with MS sheet and providing 2 Nos. 12 mm dia bar for
hooks etc i/c cost of cartage, all leads & lift, handling at
site etc. all complete as per direction of Engineer-in-
Charge.

16.94 Providing & making Gabion structure with Mechanically 1.00 Sqm 4178.00 One Cubic 4178.00
Woven Double Twisted Hexagonal Shaped Wire mesh Metre
Gabion Boxes as per IS 16014:2012, MORTH Clause
2500, of required size, Mesh Type 10x12 (D=100 mm
with tolerance of ± 2%) zinc coated, Mesh wire
diameter 3.0 mm, mechanically edged/ selvedged with
partitions at every 1m interval and shall have minimum
10 numbers of openings per meter of mesh
perpendicular to twist, tying with lacing wire of
diameter 2.2mm, supplied @3% by weight of Gabion
boxes, filled with boulders with least dimension of 200
mm, as per drawing, all complete as per direction of
Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 154 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
16.95 Providing & making Gabion structure with Mechanically 1.00 Sqm 4569.25 One Cubic 4569.00
Woven Double Twisted Hexagonal Shaped Wire mesh Metre
Gabion Boxes as per IS 16014:2012,MORTH Clause
2500, of required size, Mesh Type 10x12 (D=100 mm
with tolerance of ± 2%) Zinc+ PVC coated, Mesh wire
diameter 2.7/ 3.7mm, mechanically edged/ selvedged
with partitions at every 1m interval and shall have
minimum 10 numbers of openings per meter of mesh
perpendicular to twist, tying with lacing wire of
diameter 2.2/3.2mm(ID/OD), supplied @3% by weight
of Gabion boxes, filled with boulders with least
dimension of 200 mm, as per drawing, all complete as
per directions of Engineer-in- charge.

16.96 Providing & making Gabion structure with Mechanically 1.00 Sqm 4882.20 One Cubic 4882.00
Woven Double Twisted Hexagonal Shaped Wire mesh Metre
Gabion Boxes as per IS 16014:2012,MORTH Clause
2500, of required size, Mesh Type 10x12 (D=100 mm
with tolerance of ±2%), Zinc+ 10% Al alloy+PVC coated,
Mesh wire diameter 2.7/3.7mm (ID/OD),mechanically
edged/selvedged with partitions at every 1m interval
and shall have minimum 10 numbers of openings per
meter of mesh perpendicular to twist, tying with lacing
wire of diameter 2.2/3.2mm(ID/OD), supplied @3% by
weight of Gabion boxes, filled with boulders with least
dimension of 200 mm, as per drawing, all complete as
per directions of Engineer- in charge.

Total of the Sub-Head - Road Work : 382465.00

Sub-Head : Sanitary Installations
17.1 Providing and fixing water closet squatting pan (Indian
type W.C.pan ) with 100 mm sand cast Iron P or S trap,
10 litre low level white P.V.C. flushing cistern, including
flush pipe, with manually controlled device (handle
lever) conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good
the walls and floors wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. pan of size 1.00 No. 6767.40 Each 6767.00
580x440 mm with integral type foot rests
17.1.2 Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan 1.00 No. 11390.95 Each 11391.00
of size 585x480 mm with flush pipe and integrated type
foot rests
17.2 Providing and fixing white vitreous china pedestal type
water closet (European type W.C. pan) with seat and
lid, 10 litre low level white P.V.C. flushing cistern,
including flush pipe, with manually controlled device
(handle lever), conforming to IS : 7231, with all fittings
andfixtures complete, including cutting and making
good the walls and floors wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid 1.00 No. 6515.55 Each 6516.00

17.2.2 W.C. pan with ISI marked black solid plastic seat and lid 1.00 No. 6383.25 Each 6383.00

DSR - 2023 IN MS EXCEL Page 155 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.3 Providing and fixing white vitreous china pedestal type
water closet (European type) with seat and lid, 10 litre
low level white vitreous china flushing cistern & C.P.
flush bend with fittings & C.I. brackets, 40 mm flush
bend, overflow arrangement with specials of standard
make and mosquito proof coupling of approved
municipal design complete, including painting of fittings
and brackets, cutting and making good the walls and
floors wherever required :

17.3.1 W.C. pan with ISI marked white solid plastic seat and lid 1.00 No. 8006.60 Each 8007.00

17.3.2 W.C. pan with ISI marked black solid plastic seat and lid 1.00 No. 7874.30 Each 7874.00

17.4 Providing and fixing white vitreous china flat back or

wall corner type lipped front urinal basin of
430x260x350 mm and 340x410x265 mm sizes
respectively with automatic flushing cistern with
standard flush pipe and C.P. brass spreaders with brass
unions and G.I clamps complete, including painting of
fittings and brackets, cutting and making good the walls
and floors wherever required :

17.4.1 One urinal basin with 5 litre white P.V.C. automatic 1.00 No. 6258.75 Each 6259.00
flushing cistern
17.4.2 Range of two urinal basins with 5 litre white P.V.C. 1.00 No. 9612.40 Each 9612.00
automatic flushing cistern
17.4.3 Range of three urinal basins with 10litre white P.V.C. 1.00 No. 13417.30 Each 13417.00
automatic flushing cistern
17.4.4 Range of four urinal basins with 10 litre white P.V.C. 1.00 No. 18579.95 Each 18580.00
automatic flushing cistern
17.5 Providing and fixing white vitreous china flat back half
stall urinal of size 580x380x350 mm with white PVC
automatic flushing cistern, with fittings, standard size
C.P. brass flush pipe, spreaders with unions and clamps
(all in C.P. brass) with waste fitting as per IS : 2556, C.I.
trap with outlet grating and other couplings in C.P.
brass, including painting of fittings and cutting and
making good the walls and floors wherever required :

17.5.1 Single half stall urinal with 5 litre P.V.C. automatic 1.00 No. 12071.75 Each 12072.00
flushing cistern
17.5.2 Range of two half stall urinals with 5 litre P.V.C. 1.00 No. 18008.75 Each 18009.00
automatic flushing cistern
17.5.3 Range of three half stall urinals with 10 litre P.V.C. 1.00 No. 22058.25 Each 22058.00
automatic flushing cistern
17.5.4 Range of four half stall urinals with 10 litre P.V.C. 1.00 No. 25969.45 Each 25969.00
automatic flushing cistern
17.6 Providing and fixing one piece construction white
vitreous china squatting plate with an integral
longitudinal flushing pipe, white P.V.C. automatic
flushing cistern, with fittings, standard size G.I. / PVC
flush pipe for back and front flush with standard
spreader pipes with fittings, G.I clamps and C.P. brass
coupling complete, including painting of fittings and
cutting and making good the walls and floors etc.
wherever required :

17.6.1 Single squatting plate with 5 litre P.V.C. automatic 1.00 No. 9256.45 Each 9256.00
flushing cistern
17.6.2 Range of two squatting plates with 5 litre P.V.C. 1.00 No. 13476.35 Each 13476.00
automatic flushing cistern

DSR - 2023 IN MS EXCEL Page 156 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.6.3 Range of three squatting plates with 10 litre P.V.C. 1.00 No. 17702.20 Each 17702.00
automatic flushing cistern
17.6.4 Range of four squatting plates with 10 litre P.V.C. 1.00 No. 21203.20 Each 21203.00
automatic flushing cistern
17.7 Providing and fixing wash basin with C.I. brackets, 15
mm C.P. brass pillar taps, 32 mm C.P. brass waste of
standard pattern, including painting of fittings and
brackets, cutting and making good the walls wherever
require:

17.7.1 White Vitreous China Wash basin size 630x450 mm with 1.00 No. 2648.85 Each 2649.00
a pair of 15 mm C.P. brass pillar taps
17.7.2 White Vitreous China Wash basin size 630x450 mm with 1.00 No. 2226.35 Each 2226.00
a single 15 mm C.P. brass pillar tap
17.7.3 White Vitreous China Wash basin size 550x400 mm with 1.00 No. 2301.75 Each 2302.00
a pair of 15 mm C.P. brass pillar taps
17.7.4 White Vitreous China Flat back wash basin size 550x 1.00 No. 1879.20 Each 1879.00
400 mm with single 15 mm C.P. brass pillar tap
17.7.5 White Vitreous China Angle back wash basin size 600 x 1.00 No. 2226.35 Each 2226.00
480 mm with single 15mm C.P. brass pillar tap
17.7.6 White Vitreous China Angle back wash basin size 400 x 1.00 No. 1756.85 Each 1757.00
400 mm with single 15 mm C.P. brass pillar tap
17.7.7 White Vitreous China Flat back wash basin size 450x 1.00 No. 1513.60 Each 1514.00
300 mm with single 15mm C.P. brass pillar tap
17.7.8 White Vitreous China Surgeon type wash basin of size 1.00 No. 3600.60 Each 3601.00
660x460 mm with a pair of 15 mm C.P. brass pillar taps
with elbow including operated levers
17.7.9 White Vitreous China Surgeon type wash basin of size 1.00 No. 2940.50 Each 2941.00
660x460 mm with single 15 mm C.P. brass pillar taps
with elbow operated levers ISI Marked
17.7.10 Stainless Steel AISI-304(18/8) Round basin 405x355 mm 1.00 No. 3438.40 Each 3438.00
with single 15 mm C.P. brass pillar tap
17.7.11 Stainless Steel AISI-304(18/8) Wash basin 530x345 mm 1.00 No. 4149.75 Each 4150.00
with single 15 mm C.P. brass pillar tap
17.7B Providing and fixing wash basin with C.I. brackets, 15 1.00 No. 1550.60 Each 1551.00
mm PTMT pillar cock, 32 mm PTMT waste coupling of
standard pattern, including painting of fittings and
brackets, cutting and making good the walls wherever
required. White Vitreous China Flat back wash basin
size 550x400 mm with single 15 mm PTMT pillar cock.

17.8 Providing and fixing white vitreous china pedestal for 1.00 No. 1683.35 Each 1683.00
wash basin completely recessed at the back for the
reception of pipes and fittings.
17.9 Providing and fixing kitchen sink with C.I. brackets, C.P.
brass chain with rubber plug, 40 mm C.P. brass waste
complete, including painting the fittings and brackets,
cutting and making good the walls wherever required:

17.9.1 White glazed fire clay kitchen sink of size 600x450x 250 1.00 No. 3892.75 Each 3893.00
mm
17.10 Providing and fixing Stainless Steel A ISI 304 (18/8)
kitchen sink as per IS:13983 with C.I. brackets and
stainless steel plug 40 mm, including painting of fittings
and brackets, cutting and making good the walls
wherever required :

17.10.1 Kitchen sink with drain board

17.10.1.1 510x1040 mm bowl depth 250 mm. 1.00 No. 6945.60 Each 6946.00
17.10.1.2 510x1040 mm bowl depth 225 mm. 1.00 No. 7514.65 Each 7515.00
17.10.1.3 510x1040 mm bowl depth 200 mm. 1.00 No. 7159.00 Each 7159.00

DSR - 2023 IN MS EXCEL Page 157 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.10.1.4 510x1040 mm bowl depth 178 mm. 1.00 No. 6917.20 Each 6917.00
17.10.2 Kitchen sink without drain board
17.10.2.1 610x510 mm bowl depth 200 mm. 1.00 No. 4940.80 Each 4941.00
17.10.2.2 610x460 mm bowl depth 200 mm. 1.00 No. 3873.80 Each 3874.00
17.10.2.3 470x420 mm bowl depth 178 mm. 1.00 No. 3407.20 Each 3407.00
17.11 Providing and fixing white vitreous china laboratory sink
with C.I. brackets, C.P. brass chain with rubber plug, 40
mm C.P brass waste and 40mm C.P. brass trap with
necessary C.P. brass unions complete, including
painting of fittings and brackets, cutting and making
good the wall wherever required :

17.11.1 Size 450x300x150 mm 1.00 No. 5020.85 Each 5021.00

17.11.2 Size 600x450x200 mm 1.00 No. 6585.80 Each 6586.00
17.12 Providing and fixing draining board with C.I. brackets
including painting of brackets, cutting and making good
the walls wherever required :
17.12.1 White glazed fire clay draining board of size 600x450x 1.00 No. 1579.65 Each 1580.00
25 mm
17.13 Providing and fixing white vitreous china water closet
squatting pan (Indian type) :
17.13.1 Long pattern W.C. pan of size 580 mm 1.00 No. 1959.80 Each 1960.00
17.13.2 Orissa pattern W.C. pan of size 580x440 mm 1.00 No. 3169.05 Each 3169.00
17.14 Extra for using colored W.C. pan instead of white W.C.
pan
17.14.1 Orissa pattern W.C. pan 580x440 mm 1.00 No. 426.80 Each 427.00
17.15 Providing and fixing white vitreous china pedestal type 1.00 No. 2784.95 Each 2785.00
(European type/ wash down type) water closet pan.

17.16 Extra for using coloured pedestal type W.C pan 1.00 No. 170.70 Each 171.00
(European type) with low level cistern of same colour
instead of white vitreous china W.C pan and cistern.
17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible 1.00 No. 349.15 Each 349.00
tube upto 1 metre long with S.S. triangular plate to
Eureopean type W.C. of quality and make as approved
by Engineer - in - charge.

17.17 Providing and fixing a pair of white vitreous china foot

rests of standard pattern for squatting pan water
closet :
17.17.1 250x130x30 mm 1.00 pairs 244.85 One Pair 245.00
17.17.2 250x125x25 mm 1.00 pairs 256.25 One Pair 256.00
17.18 Providing and fixing P.V.C. low level flushing cistern
with manually controlled device (handle lever)
conforming to IS : 7231, with all fittings and fixtures
complete.

17.18.1 10 litre capacity - White 1.00 No. 1190.65 Each 1191.00

17.18.2 10 litre capacity - coloured 1.00 No. 1136.60 Each 1137.00
17.19 Providing and fixing controlled flush, low level cistern
made of vitreous china with all fittings complete.
17.19.1 10 litre (full flush) capacity-white 1.00 No. 2243.75 Each 2244.00
17.19.2 10 litre (full flush) capacity-coloured 1.00 No. 2912.40 Each 2912.00
17.20 Providing and fixing solid plastic seat with lid for
pedestal type W.C. pan complete :
17.20.1 White solid plastic seat with lid 1.00 No. 684.85 Each 685.00
17.20.2 Black solid plastic seat with lid 1.00 No. 552.55 Each 553.00
17.20.3 Coloured (other than black & white) solid plastic seat 1.00 No. 590.95 Each 591.00
with lid
17.22 Providing and fixing G.I. inlet connection for flush pipe 1.00 No. 142.85 Each 143.00
connecting with W.C. pan.

DSR - 2023 IN MS EXCEL Page 158 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.22A Providing and fixing CP Brass 32mm size Bottle Trap of 1.00 No. 1034.80 Each 1035.00
approved quality & make and as per the direction of
Engineer-in-charge.
17.23 Providing and fixing white vitreous china flat back or 1.00 No. 1648.95 Each 1649.00
wall corner type lipped front urinal basin of
430x260x350 mm or 340x410x265 mm sizes
respectively.

17.24 Providing and fixing white vitreous china squatting plate 1.00 No. 4048.65 Each 4049.00
urinal with integral rim longitudinal flush pipe.
17.25 Providing and fixing white vitreous china wash basin
including making all connections but excluding the cost
of fittings :
17.25.1 Flat back wash basin of size 630x450 mm. 1.00 No. 1339.70 Each 1340.00
17.25.2 Flat back wash basin of size 550x400 mm. 1.00 No. 992.60 Each 993.00
17.25.3 Angle back wash basin of size 600x480 mm. 1.00 No. 1339.70 Each 1340.00
17.25.4 Angle back wash basin of size 400x400mm. 1.00 No. 870.25 Each 870.00
17.25.5 Flat back wash basin of size 450x300 mm. 1.00 No. 627.00 Each 627.00
17.25.6 Surgeon type wash basin of size 660x460 mm. 1.00 No. 1816.30 Each 1816.00
17.26 Providing and fixing kitchen sink including making all
connections excluding cost of fittings.
17.26.1 White glazed fire clay sink of size 600x450x250 mm. 1.00 No. 2199.80 Each 2200.00
17.27 Providing and fixing white vitreous china laboratory sink
including making all connections excluding cost of
fittings:
17.27.1 Size 450x300x150 mm. 1.00 No. 2512.75 Each 2513.00
17.27.2 Size 600x450x200 mm. 1.00 No. 4077.65 Each 4078.00
17.28 Providing and fixing P.V.C. waste pipe for sink or wash
basin including P.V.C. waste fittings complete.
17.28.1 Semi rigid pipe
17.28.1.1 32 mm dia 1.00 No. 103.90 Each 104.00
17.28.1.2 40 mm dia 1.00 No. 116.70 Each 117.00
17.28.2 Flexible pipe
17.28.2.1 32 mm dia 1.00 No. 119.55 Each 120.00
17.28.2.2 40 mm dia 1.00 No. 119.55 Each 120.00
17.29 Providing and fixing 100 mm sand cast Iron grating for 1.00 No. 53.25 Each 53.00
gully trap.
17.30 Providing and fixing in position 25mm diameter 1.00 No. 55.65 Each 56.00
mosquito proof coupling of approved municipal design.

17.31 Providing and fixing 600x450 mm beveled edge mirror 1.00 No. 1607.95 Each 1608.00
of superior glass (of approved quality) complete with 6
mm thick hard board ground fixed to wooden cleats
with C.P. brass screws and washers complete.

17.32 Providing and fixing mirror of superior glass (of

approved quality) and of required shape and size with
plastic moulded frame of approved make and shade
with 6 mm thick hard board backing :

17.32.1 Circular shape 450 mm dia. 1.00 No. 1479.05 Each 1479.00
17.32.2 Rectangular shape 453x357 mm 1.00 No. 1361.80 Each 1362.00
17.32.3 Oval shape 450x350 mm (outer dimensions) 1.00 No. 1377.10 Each 1377.00
17.32.4 Rectangular shape 1500x450 mm 1.00 No. 2093.00 Each 2093.00
17.33 Providing and fixing 600x120x5 mm glass shelf with 1.00 No. 1083.50 Each 1084.00
edges round off, supported on anodised aluminium
angle frame with C.P. brass brackets and guard rail
complete fixed with 40 mm long screws, rawl plugs etc.,
complete.

17.34 Providing and fixing toilet paper holder :

17.34.1 C.P. brass 1.00 No. 803.70 Each 804.00

DSR - 2023 IN MS EXCEL Page 159 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.34.2 Vitreous china 1.00 No. 546.35 Each 546.00
17.35 Providing and fixing soil, waste and vent pipes :
17.35.1 100 mm dia.
17.35.1.1 Sand cast iron S&S pipe as per IS: 1729. 1.00 m 1151.90 One Running 1152.00
Metre
17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe 1.00 m 1180.75 One Running 1181.00
as per IS: 3989. Metre
17.35.1.3 Hubless centrifugally cast (spun) iron pipes epoxy 1.00 m 1169.30 One Running 1169.00
coated inside & outside IS:15905 Metre
17.35.2 75 mm diameter :
17.35.2.1 Sand cast iron S&S pipe as per IS: 1729. 1.00 m 1044.75 One Running 1045.00
Metre
17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 1.00 m 1186.00 One Running 1186.00
3989. Metre
17.35.2.3 Hubless centrifugally cast (spun) iron pipes epoxy 1.00 m 964.25 One Running 964.00
coated inside & outside IS:15905 Metre
17.36 Providing and filling the joints with spun yarn, cement
slurry and cement mortar 1:2 ( 1 cement : 2 fine sand)
in S.C.I./ C.I. Pipes :
17.36.1 75 mm dia pipe 1.00 No. 168.20 Each 168.00
17.36.2 100 mm dia pipe 1.00 No. 198.15 Each 198.00
17.37 Providing and fixing M.S. holder-bat clamps of approved
design to Sand Cast iron/cast iron (spun) pipe
embedded in and includingcement concrete blocks
10x10x10 cm of 1:2:4 mix (1 cement : 2coarse sand : 4
graded stone aggregate 20 mm nominal size), including
cost of cutting holes and making good the walls etc. :

17.37.1 For 100 mm dia. Pipe 1.00 No. 362.85 Each 363.00
17.37.2 For 75 mm dia. Pipe 1.00 No. 360.00 Each 360.00
17.38 Providing and fixing bend of required degree with
access door, insertion rubber washer 3 mm thick, bolts
and nuts complete.
17.38.1 100 mm dia
17.38.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 598.50 Each 599.00
17.38.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 705.20 Each 705.00
17.38.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 567.20 Each 567.00
inside & outside as per IS:15905
17.38.2 75 mm dia
17.38.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 501.45 Each 501.00
17.38.2.2 Sand cast iron S&S as per IS- 3989 1.00 No. 522.80 Each 523.00
17.38.2.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 418.95 Each 419.00
inside & outside as per IS:15905
17.39 Providing and fixing plain bend of required degree.
17.39.1 100 mm dia
17.39.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 470.45 Each 470.00
17.39.1.2 Sand cast iron S&S as per IS : 3989 1.00 No. 570.05 Each 570.00
17.39.1.3 Hubless centrifugally cast (spun) iron pipes epoxy 1.00 No. 368.00 Each 368.00
coated inside & outside as per IS:15905
17.39.2 75 mm dia
17.39.2.1 Sand cast iron S&S as per IS -1729 1.00 No. 376.25 Each 376.00
17.39.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 390.50 Each 391.00
17.39.2.3 Hubless centrifugally cast (spun) iron pipes epoxy 1.00 No. 252.50 Each 253.00
coated inside & outside as per IS:15905
17.40 Providing and fixing heel rest sanitary bend
17.40.1 100 mm dia
17.40.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 584.25 Each 584.00
17.40.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 548.70 Each 549.00
17.40.2 75 mm dia

DSR - 2023 IN MS EXCEL Page 160 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.40.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 490.05 Each 490.00
17.40.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 504.30 Each 504.00
17.41 Providing and fixing double equal junction of required
degree with access door, insertion rubber washer 3 mm
thick, bolts and nuts complete :
17.41.1 100x100x100x100 mm
17.41.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 1138.65 Each 1139.00
17.41.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1103.10 Each 1103.00
17.41.2 75x75x75x75 mm
17.41.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 842.90 Each 843.00
17.41.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 885.60 Each 886.00
17.42 Providing and fixing double equal plain junction of
required degree.
17.42.1 100x100x100x100 mm
17.42.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 939.90 Each 940.00
17.42.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1075.05 Each 1075.00
17.42.1.3 Hubless centrifugally cast (spun) iron pipes epoxy 1.00 No. 760.70 Each 761.00
coated inside & outside as per IS:15905
17.42.2 75x75x75x75 mm
17.42.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 625.20 Each 625.00
17.42.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 803.05 Each 803.00
17.42.2.3 Hubless centrifugally cast (spun) iron pipes epoxy 1.00 No. 418.95 Each 419.00
coated inside & outside as per IS:15905
17.43 Providing and fixing single equal plain junction of
required degree with access door, insertion rubber
washer 3 mm thick, bolts and nuts complete.
17.43.1 100x100x100 mm
17.43.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 726.55 Each 727.00
17.43.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 925.70 Each 926.00
17.43.2 75x75x75 mm
17.43.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 629.50 Each 630.00
17.43.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 665.05 Each 665.00
17.44 Providing and fixing single equal plain junction of
required degree :
17.44.1 100x100x100 mm
17.44.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 626.95 Each 627.00
17.44.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 811.90 Each 812.00
17.44.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 581.45 Each 581.00
inside & outside as per IS:15905
17.44.2 75x75x75 mm
17.44.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 504.30 Each 504.00
17.44.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 561.20 Each 561.00
17.44.2.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 337.85 Each 338.00
inside & outside as per IS:15905
17.45 Providing and fixing double unequal junction of
required degree with access door, insertion rubber
washer 3 mm thick, bolts and nuts complete :
17.45.1 100x100x75x75 mm
17.45.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 1153.30 Each 1153.00
17.45.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1601.45 Each 1601.00
17.46 Providing and fixing double unequal plain junction of
required degree:
17.46.1 100x100x75x75 mm
17.46.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 954.15 Each 954.00
17.46.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1402.30 Each 1402.00
17.46.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 607.05 Each 607.00
inside & outside as per IS:15905

DSR - 2023 IN MS EXCEL Page 161 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.47 Providing and fixing single unequal junction of required
degree with access door, insertion rubber washer 3 mm
thick, bolts and nuts complete :
17.47.1 100x100x75 mm
17.47.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 911.45 Each 911.00
17.47.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1146.20 Each 1146.00
17.48 Providing and fixing single unequal plain junction of
required degree :
17.48.1 100x100x75 mm
17.48.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 811.90 Each 812.00
17.48.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1032.40 Each 1032.00
17.48.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 551.55 Each 552.00
inside & outside as per IS:15905
17.49 Providing and fixing double equal plain invert branch of
required degree:
17.49.1 100x100x100x100 mm
17.49.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 883.00 Each 883.00
17.49.1.2 Sand cast iron S&S as per IS 3989 1.00 No. 989.70 Each 990.00
17.49.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 1106.35 Each 1106.00
inside & outside as per IS:15905
17.49.2 75x75x75x75 mm
17.49.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 660.80 Each 661.00
17.49.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 803.05 Each 803.00
17.50 Providing and fixing single equal plain invert branch of
required degree:
17.50.1 100x100x100 mm
17.50.1.1 Sand cast iron S&S as per IS 1729 1.00 No. 698.05 Each 698.00
17.50.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 747.85 Each 748.00
17.50.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 645.45 Each 645.00
inside & outside as per IS:15905
17.50.2 75x75x75 mm
17.50.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 575.45 Each 575.00
17.50.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 575.45 Each 575.00
17.50.2.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 401.90 Each 402.00
inside & outside as per IS:15905
17.51 Providing and fixing double unequal invert branch of
required degree :
17.51.1 100x100x75x75 mm
17.51.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 1011.05 Each 1011.00
17.51.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 1274.25 Each 1274.00
17.52 Providing and fixing single unequal plain invert branch
of required degree :
17.52.1 100x100x75 mm
17.52.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 804.80 Each 805.00
17.52.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 996.85 Each 997.00
17.52.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 658.25 Each 658.00
inside & outside as per IS:15905
17.53 Providing and fixing sand cast iron S&S off sets as per IS:
1729
17.53.1 76 mm off sets
17.53.1.1 With 75 mm dia pipe 1.00 No. 376.25 Each 376.00
17.53.1.2 With 100 mm dia pipe 1.00 No. 603.90 Each 604.00
17.53.2 114 mm off sets
17.53.2.1 With 75 mm dia pipe 1.00 No. 527.35 Each 527.00
17.53.2.2 With 100 mm dia Pipe 1.00 No. 648.30 Each 648.00
17.53.3 152 mm off sets
17.53.3.1 With 75 mm dia Pipe 1.00 No. 619.90 Each 620.00
17.53.3.2 With 100 mm dia Pipe 1.00 No. 769.25 Each 769.00

DSR - 2023 IN MS EXCEL Page 162 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.53A Providing and fixing Hubless centrifugally cast iron
offsets epoxy coated inside & outside as per IS:15905
17.53A.1 65 mm offsets
17.53A.1.1With 100 mm dia pipe 1.00 No. 547.00 Each 547.00
17.53A.1.2With 75 mm dia pipe 1.00 No. 454.50 Each 455.00
17.54 Providing and fixing sand cast iron S&S off sets as per IS:
3989.
17.54.1 75 mm off sets
17.54.1.1 With 75 mm dia pipe 1.00 No. 418.95 Each 419.00
17.54.2 150 mm off sets
17.54.2.1 With 75 mm dia pipe 1.00 No. 585.55 Each 586.00
17.54.2.2 With 100 mm dia Pipe 1.00 No. 734.95 Each 735.00
17.54A Providing and fixing Hubless centrifugally cast iron
offsets epoxy coated inside & outside as per IS:15905
17.54A.1 130 mm offsets
17.54A.1.1With 100 mm dia 1.00 No. 632.65 Each 633.00
17.54A.1.2With 75 mm dia 1.00 No. 465.90 Each 466.00
17.55 Providing and fixing door piece, insertion rubber washer
3mm thick, bolts & nuts complete :
17.55.1 100 mm
17.55.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 783.45 Each 783.00
17.55.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 683.85 Each 684.00
17.55.2 75 mm
17.55.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 501.45 Each 501.00
17.55.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 537.00 Each 537.00
17.56 Providing and fixing terminal guard:
17.56.1 100 mm
17.56.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 442.00 Each 442.00
17.56.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 506.00 Each 506.00
17.56.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 427.80 Each 428.00
inside & outside as per IS:15905
17.56.2 75 mm
17.56.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 340.70 Each 341.00
17.56.2.2 Sand cast iron S&S as per IS - 3989 1.00 No. 404.75 Each 405.00
17.57 Providing and fixing collar:
17.57.1 100 mm
17.57.1.1 Sand cast iron S&S as per IS - 1729 1.00 No. 463.35 Each 463.00
17.57.1.2 Sand cast iron S&S as per IS - 3989 1.00 No. 513.15 Each 513.00
17.57.2 75 mm
17.57.2.1 Sand cast iron S&S as per IS - 1729 1.00 No. 305.15 Each 305.00
17.57.2.2 Sand cast iron S&S as per IS- 3989 1.00 No. 362.05 Each 362.00
17.57A Providing and fixing shielded coupling for Hubless
centrifugally cast iron pipe
17.57A.1 100 mm dia
17.57A.1.1SS 304 grade coupling with EPDM rubber gasket 1.00 No. 432.05 Each 432.00
17.57A.2 75 mm dia
17.57A.2.1SS 304 grade coupling with EPDM rubber gasket 1.00 No. 389.05 Each 389.00
17.58 Providing lead caulked joints to sand cast
iron/centrifugally cast (spun) iron pipes and fittings of
diameter:
17.58.1 100 mm 1.00 No. 622.50 Each 623.00
17.58.2 75 mm 1.00 No. 526.25 Each 526.00
17.58.3 50 mm 1.00 No. 423.15 Each 423.00
17.59 Providing and fixing M.S. stays and clamps for sand cast
iron/centrifugally cast (spun) iron pipes of diameter :

17.59.1 100 mm 1.00 No. 139.70 Each 140.00

17.59.2 75 mm 1.00 No. 90.30 Each 90.00
17.59.3 50 mm 1.00 No. 81.85 Each 82.00

DSR - 2023 IN MS EXCEL Page 163 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.60 Providing and fixing trap of self cleansing design with
screwed down or hinged grating with or without vent
arm complete, including cost of cutting and making
good the walls and floors :

17.60.1 100 mm inlet and 100 mm outlet

17.60.1.1 Sand cast iron S&S as per IS: 3989. 1.00 No. 1996.50 Each 1997.00
17.60.1.2 Sand Cast Iron S&S as per IS: 1729. 1.00 No. 1683.55 Each 1684.00
17.60.1.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 854.55 Each 855.00
inside & outside as per IS:15905
17.60.2 100 mm inlet and 75 mm outlet
17.60.2.1 Sand cast iron S&S as per IS - 3989 1.00 No. 1975.15 Each 1975.00
17.60.2.2 Sand Cast Iron S&S as per IS- 1729. 1.00 No. 1558.35 Each 1558.00
17.60.2.3 Hubless centrifugally cast (spun) iron epoxy coated 1.00 No. 591.40 Each 591.00
inside & outside as per IS:15905
17.61 Cutting chases in brick masonry walls for following
diameter sand cast iron/centrifugally cast (spun) iron
pipes and making good the same with cement concrete
1:3:6 ( 1 cement : 3 coarse sand :6graded stone
aggregate 12.5 mm nominal size), including necessary
plaster and pointing in cement mortar 1:4 (1 cement : 4
coarse sand) :

17.61.1 100 mm dia. 1.00 m 713.20 One Running 713.00

Metre
17.61.2 75 mm dia. 1.00 m 513.25 One Running 513.00
Metre
17.61.3 50 mm dia. 1.00 m 336.00 One Running 336.00
Metre
17.62 Painting C.I. cistern with bitumastic or any other anti- 1.00 No. 1020.60 Each 1021.00
corrosive paint inside and white paint over a coat of
zinc chromate yellow primer (of approved quality ) on
the outside surface of the cistern, flush pipe, other
fittings, etc. complete for new work.

17.63 Re-painting C.I. cistern with bitumastic or any other 1.00 No. 673.70 Each 674.00
anti-corrosive paint inside and white paint on the
outside surface of the cistern, flush pipe, other fittings,
etc. complete, including polishing of wooden seat and
lid and cleaning of W.C. pan with acid wherever
necessary..

17.64 Repainting C.I. cistern with synthetic enamel paint of 1.00 No. 292.55 Each 293.00
approved colour, brand and manufacture on the
outside surface of cistern, flush pipe, other fittings etc.
complete.

17.65 Painting sand cast iron/ centrifugally cast (spun) iron

soil, waste vent pipes and fittings with two coats of
synthetic enamel paint of any colour such as chocolate
grey, or buff etc. over a coat of primer (of approved
quality) for new work :

17.65.1 100 mm diameter pipe 1.00 m 82.80 One Metre 83.00

17.65.2 75 mm diameter pipe 1.00 m 62.95 One Metre 63.00
17.66 Repainting sand cast iron/ centrifugally cast iron (spun)
iron, soil, waste, vent pipes and fittings with one coat of
synthetic enamel paint of any colour such as chocolate,
grey or buff etc :

17.66.1 100 mm diameter pipe 1.00 m 39.50 One Metre 40.00

17.66.2 75 mm diameter pipe 1.00 m 29.55 One Metre 30.00
17.67 Repainting bath tub of size 1700x730x430 mm with 1.00 No. 804.30 Each 804.00
enamel paint.

DSR - 2023 IN MS EXCEL Page 164 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.68 Providing and fixing vitreous china dual purpose closet
suitable for use as squatting pan or European type
water closet (Anglo Indian W.C pan) with seat & lid
fixed with C.P. brass hinges and rubber buffers, 10 litre
low level flushing cistern with fitting and brackets, 40
mm flush bend, 20 mm over flow pipe, with specials of
standard make and mosquito proof coupling of
approved municipal design complete, including painting
of fittings and brackets, cutting and making good the
walls and floors wherever required:

17.68.1 White vitreous china dual purpose WC pan with white 1.00 No. 11847.65 Each 11848.00
solid plastic seat and lid with white vitreous china
flushing cistern and C.P. flush bend.
17.69 Providing and fixing PTMT Waste Coupling for wash
basin and sink, of approved quality and colour.
17.69.1 Waste coupling 31 mm dia of 79 mm length and 62 mm 1.00 No. 115.30 Each 115.00
breadth weighing not less than 45 gms.
17.69.2 Waste coupling 38 mm dia of 83 mm length and 77 mm 1.00 No. 122.40 Each 122.00
breadth, weighing not less than 60 gms.
17.70 Providing and fixing PTMT Bottle Trap for Wash basin
and sink.
17.70.1 Bottle trap 31mm single piece moulded with height of 1.00 No. 367.10 Each 367.00
270 mm, effective length of tail pipe 260 mm from the
centre of the waste coupling, 77 mm breadth with 25
mm minimum water seal, weighing not less than 260
gms

17.70.2 Bottle trap 38 mm single piece moulded with height of 1.00 No. 375.65 Each 376.00
270 mm, effective length of tail pipe 260 mm from the
centre of the waste coupling, 77 mm breadth with 25
mm minimum water seal, weighing not less than 263
gms

17.71 Providing and fixing PTMT liquid soap container 109 1.00 No. 168.35 Each 168.00
mm wide, 125 mm high and 112 mm distance from wall
of standard shape with bracket of the same materials
with snap fittings of approved quality and colour,
weighing not less than 105 gms.

17.72 Providing and fixing PTMT towel ring trapezoidal shape 1.00 No. 231.95 Each 232.00
215 mm long, 200 mm wide with minimum distances of
37 mm from wall face with concealed fittings
arrangement of approved quality and colour, weighing
not less than 88 gms.

17.73 Providing and fixing PTMT towel rail complete with

brackets fixed to wooden cleats with CP brass screws
with concealed fittings arrangement of approved
quality and colour.

17.73.1 450 mm long towel rail with total length of 495 mm, 78 1.00 No. 673.40 Each 673.00
mm wide and effective height of 88 mm, weighing not
less than 170 gms.
17.73.2 600 mm long towel rail with total length of 645 mm, 1.00 No. 708.95 Each 709.00
width 78 mm and effective height of 88 mm, weighing
not less than 190 gms.
17.74 Providing and fixing PTMT shelf 440 mm long, 124 mm 1.00 No. 713.20 Each 713.00
width and 36 mm height of approved quality and
colour, weighing not less than 300 gms.
17.75 Providing and fixing PTMT 15 mm Urinal spreader size 1.00 No. 107.20 Each 107.00
95x69x100 mm with 1/2" BSP thread and shapes,
weighing not less than 60 gms.

DSR - 2023 IN MS EXCEL Page 165 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
17.76 Providing and fixing PTMT urinal cock of approved
quality and colour.
17.76.1 15 mm nominal bore, 80 mm long. 42 mm high and 30 1.00 No. 175.40 Each 175.00
mm wide with BSP female threads weighing not less
than 48 gms.
17.77 Providing and fixing M.S. holder bat clamp of approved
design to sand cast iron/ cast iron (spun) pipes
comprising of M.S. flat brackets made of 50x5 mm flat
of specified shape, projecting 75 mm outside the wall
surface and fixed on wall with 4nos, 6mm dia expansion
hold fasteners, including drilling necessary holes in brick
wall/ CC/RCC surface and the cost of bolts etc. The
pipes shall be fixed to the already fixed brackets with
the help of 30 mm x1.6 mm galvanised M.S. flats of
specified shape and of total length 420 mm and shall be
fixed with M.S. nuts, bolts, & washers of size 25x6 mm,
one bolts on each side of the pipe.

17.77.1 Total bracket length 580 mm of approved shape and 1.00 No. 304.05 Each 304.00
design (for single 100 mm dia pipe).
17.77.2 Total bracket length 810 mm of approved shape and 1.00 No. 378.10 Each 378.00
design (for two 100 mm dia pipes).
17.77.3 Total bracket length 1040 mm of approved shape and 1.00 No. 451.90 Each 452.00
design (for three 100 mm dia pipes).
17.78 Providing and fixing white vitreous china extended wall 1.00 No. 14999.15 Each 14999.00
mounting water closet of size 780x370x690 mm of
approved shape including providing & fixing white
vitreous china cistern with dual flush fitting, of flushing
capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),
including seat cover, and cistern fittings, nuts, bolts and
gasket etc complete.

17.79 Providing & fixing white vitreous china water less urinal 1.00 No. 18088.45 Each 18088.00
of size 600 x 330 x 315 mm having antibacterial /germs
free ceramic surface, fixed with cartridge having debris
catcher and hygiene seal.

17.80 Providing and fixing white vitreous china battery based 1.00 No. 7979.20 Each 7979.00
infrared sensor operated urinal of approx. size 610 x
390 x 370 mm having pre & post flushing with water
(250 ml & 500 ml consumption), having water inlet
from back side, including fixing to wall with suitable
brackets all as per manufacturers specification and
direction of Engineer-in-charge.

17.81 Providing and fixing floor mounted, white vitreous china 1.00 No. 18212.90 Each 18213.00
single piece, double traps syphonic water closet of
approved brand/make, shape, size and pattern
including integrated white vitreous china cistern of
capacity 10 litres with dual flushing system, including all
fittings and fixtures with seat cover, cistern fittings,
nuts, bolts and gasket etc including making connection
with the existing P/S trap, complete in all respect as per
directions of Engineer-in-Charge.

Total of the Sub-Head - Sanitary Installations : 535787.00

Sub-Head : Water Supply

DSR - 2023 IN MS EXCEL Page 166 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.1 Providing and fixing Polyethelene-Aluminium-
Polyethelene PE-AL-PE Composite Pressure Pipes
conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & coldwater
supply, capable to withstand temperature up to 80°C,
including all special fittings of composite material
(engineering plastic blend and brass inserts wherever
required) e.g. elbows, tees, reducers, couplers &
connectors etc., with clamps at 1.00 metre spacing.This
includes testing of joints complete as per direction of
the Engineer-in-charge. INTERNAL WORK - EXPOSED ON
WALL

18.1.1 1216 (16 mm OD) pipe 1.00 m 286.75 One Running 287.00
Metre
18.1.2 1620 (20 mm OD) pipe 1.00 m 331.20 One Running 331.00
Metre
18.1.3 2025 (25 mm OD) pipe 1.00 m 401.55 One Running 402.00
Metre
18.1.4 2532 (32 mm OD) pipe 1.00 m 529.85 One Running 530.00
Metre
18.1.5 3240 (40 mm OD) pipe 1.00 m 684.45 One Running 684.00
Metre
18.1.6 4050 (50 mm OD) pipe 1.00 m 939.70 One Running 940.00
Metre
18.2 Providing and fixing Polyethylene- Aluminium -
Polyethylene (PE-AL- PE) Composite Pressure Pipes
conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water
supply, capable to withstand temperature up to 80°C,
including all special fittings of composite material
(engineering plastic blend and brass inserts wherever
required) e.g. elbows, tees, reducers, couplers &
connectors etc. with clamps at 1.00 metre spacing. This
includes the costs of cutting chases and including
testing of joints complete as per direction of the
engineer in charge. Concealed work, including cutting
chases and making good the wall etc.

18.2.1 1216 (16mm OD) pipe 1.00 m 522.70 One Running 523.00
Metre
18.2.2 1620 (20 mm OD) pipe 1.00 m 557.55 One Running 558.00
Metre
18.2.3 2025 (25 mm OD) pipe 1.00 m 627.25 One Running 627.00
Metre
18.2.4 2532 (32 mm OD) pipe 1.00 m 754.20 One Running 754.00
Metre
18.3 Providing and fixing Polyethylene- Aluminium-
Polyethylene (PE-AL- PE) Composite Pressure Pipes
conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water
supply, capable to withstand temperature up to 80°C
including all special fittings of composite material
(engineering plastic blend and brass inserts wherever
required ) e.g. elbows, tees, reducers, couplers &
connectors etc. with trenching, refilling and testing of
joints complete as per direction of the engineer in
charge : External work

18.3.1 1216 (16 mm OD) pipe 1.00 m 263.20 One Running 263.00
Metre

DSR - 2023 IN MS EXCEL Page 167 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.3.2 1620 (20 mm OD ) pipe. 1.00 m 289.10 One Running 289.00
Metre
18.3.3 2025 (25 mm OD ) pipe. 1.00 m 340.85 One Running 341.00
Metre
18.3.4 2532 (32 mm OD ) pipe. 1.00 m 435.20 One Running 435.00
Metre
18.3.5 3240 (40 mm OD ) pipe. 1.00 m 544.55 One Running 545.00
Metre
18.3.6 4050 (50 mm OD ) pipe. 1.00 m 799.80 One Running 800.00
Metre
18.4 Providing and fixing 3 layer PP-R (Poly propylene
Random copolymer) pipes confirming to IS 15801, UV
stabilized & anti- microbial fusion welded, having
thermal stability for hot & cold water supply, including
all PP - R plain & brass threadedpolypropylene random
fittings, i/c fixing the pipe with clamps at 1.00 m
spacing. This includes testing of joints complete as per
direction of Engineer-in-Charge.Internal Exposed on
walls.

18.4.1 PN - 16 Pipe, 20mm OD (SDR-7.4) 1.00 m 272.00 One Running 272.00

Metre
18.4.2 PN - 16 Pipe, 25mm OD (SDR-7.4) 1.00 m 318.35 One Running 318.00
Metre
18.4.3 PN - 16 Pipe, 32mm OD (SDR-7.4) 1.00 m 362.90 One Running 363.00
Metre
18.4.4 PN - 16 Pipe, 40mm OD (SDR-7.4) 1.00 m 545.75 One Running 546.00
Metre
18.4.5 PN - 10 Pipe, 50mm OD (SDR-11) 1.00 m 580.10 One Running 580.00
Metre
18.5 Providing and fixing 3 layer PP-R (Poly propylene
Random copolymer) pipes confirming to IS:15801, UV
stabilized & anti- microbial fusion welded, having
thermal stability for hot & cold water supply, including
all PP - R plain & brass threadedpolypropylene random
fittings, i/c fixing the pipe with clamps at 1.00 m
spacing. This includes the cost of cutting chases
andmaking good the same including testing of joints
complete as per direction of Engineer-in-
Charge.Concealed work,including cutting chases and
making good the wall etc.

18.5.1 PN - 16 Pipe, 20mm OD (SDR-7.4) 1.00 m 477.85 One Running 478.00

Metre
18.5.2 PN - 16 Pipe, 25mm OD (SDR-7.4) 1.00 m 515.20 One Running 515.00
Metre
18.5.3 PN - 16 Pipe, 32mm OD (SDR-7.4) 1.00 m 561.45 One Running 561.00
Metre
18.6 Providing and fixing 3 layer PP-R (Poly propylene
Random copolymer) pipes confirming to IS:15801 UV
stabilized & anti -microbial fusion welded, having
thermal stability for hot & cold water supply, including
all PP - R plain & brass threadedpolypropylene random
fittings, including trenching, refilling & testing of joints
complete as per direction of Engineer-in-
Charge.External work

18.6.1 PN - 16 Pipe, 20mm OD (SDR-7.4) 1.00 m 224.95 One Running 225.00

Metre
18.6.2 PN - 16 Pipe, 25 mm OD (SDR-7.4) 1.00 m 265.05 One Running 265.00
Metre

DSR - 2023 IN MS EXCEL Page 168 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.6.3 PN - 16 Pipe, 32 mm OD (SDR-7.4) 1.00 m 316.25 One Running 316.00
Metre
18.6.4 PN - 16 Pipe, 40 mm OD (SDR-7.4) 1.00 m 415.10 One Running 415.00
Metre
18.6.5 PN - 10 Pipe, 50 mm OD (SDR-11) 1.00 m 450.95 One Running 451.00
Metre
18.6.6 PN - 10 Pipe, 63 mm OD (SDR-11) 1.00 m 597.75 One Running 598.00
Metre
18.6.7 PN - 10 Pipe, 75 mm OD (SDR-11) 1.00 m 696.75 One Running 697.00
Metre
18.6.8 PN - 10 Pipe, 90 mm OD (SDR-11) 1.00 m 975.30 One Running 975.00
Metre
18.6.9 PN - 10 Pipe, 110 mm OD (SDR-11) 1.00 m 1301.35 One Running 1301.00
Metre
18.6.10 PN - 10 Pipe, 160 mm OD (SDR-11) 1.00 m 2746.85 One Running 2747.00
Metre
18.6A Providing and fixing PPR Unions
18.6A.1 PPR Union 20 mm 1.00 No. 315.50 Each 316.00
18.6A.2 PPR Union 25 mm 1.00 No. 334.00 Each 334.00
18.6A.3 PPR Union 32 mm 1.00 No. 403.70 Each 404.00
18.6A.4 PPR Union 40 mm 1.00 No. 543.10 Each 543.00
18.6A.5 PPR Union 50 mm 1.00 No. 782.10 Each 782.00
18.6A.6 PPR Union 63 mm 1.00 No. 913.00 Each 913.00
18.6A.7 PPR Union 75 mm 1.00 No. 1684.05 Each 1684.00
18.7 Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass threaded
fittings, including fixing the pipe with clamps at 1.00 m
spacing. This includes jointing of pipes & fittings with
one step CPVC solvent cement and testing of joints
complete as per direction of Engineer in Charge. :
Internal work - Exposed on wall

18.7.1 15 mm nominal outer dia. Pipes. 1.00 m 286.80 One Running 287.00
Metre
18.7.2 20 mm nominal outer dia. Pipes. 1.00 m 335.00 One Running 335.00
Metre
18.7.3 25 mm nominal outer dia .Pipes. 1.00 m 401.55 One Running 402.00
Metre
18.7.4 32 mm nominal outer dia. Pipes. 1.00 m 518.75 One Running 519.00
Metre
18.7.5 40 mm nominal outer dia. Pipes. 1.00 m 702.95 One Running 703.00
Metre
18.7.6 50 mm nominal outer dia. Pipes. 1.00 m 934.15 One Running 934.00
Metre
18.8 Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass threaded
fittings, i/c fixing the pipe with clamps at 1.00 m
spacing. This includes jointing of pipes & fittings with
one step CPVC solvent cement and the cost of cutting
chases and making good the same including testing of
joints complete as per direction of Engineer in
Charge. :Concealed work, including cutting chases and
making good the walls etc.

18.8.1 15 mm nominal outer dia .Pipes. 1.00 m 497.80 One Running 498.00
Metre
18.8.2 20 mm nominal outer dia .Pipes. 1.00 m 537.60 One Running 538.00
Metre

DSR - 2023 IN MS EXCEL Page 169 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.8.3 25 mm nominal outer dia .Pipes. 1.00 m 627.25 One Running 627.00
Metre
18.8.4 32 mm nominal outer dia .Pipes. 1.00 m 739.30 One Running 739.00
Metre
18.9 Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply including all CPVC plain & brass threaded
fittings. This includes jointing of pipes & fittings with
one step CPVC solvent cement, trenching, refilling &
testing of joints complete as per direction of Engineer in
Charge : External work

18.9.1 15 mm nominal outer dia. Pipes. 1.00 m 244.70 One Running 245.00
Metre
18.9.2 20 mm nominal outer dia. Pipes. 1.00 m 274.30 One Running 274.00
Metre
18.9.3 25 mm nominal outer dia. Pipes. 1.00 m 355.40 One Running 355.00
Metre
18.9.4 32 mm nominal outer dia. Pipes. 1.00 m 438.60 One Running 439.00
Metre
18.9.5 40 mm nominal outer dia. Pipes. 1.00 m 563.05 One Running 563.00
Metre
18.9.6 50 mm nominal outer dia. Pipes. 1.00 m 794.25 One Running 794.00
Metre
18.9.7 62.50 mm nominal inner dia. Pipes. 1.00 m 1674.40 One Running 1674.00
Metre
18.9.8 75 mm nominal inner dia. Pipes. 1.00 m 2166.35 One Running 2166.00
Metre
18.9.9 100mm nominal inner dia. Pipes. 1.00 m 3271.70 One Running 3272.00
Metre
18.9.10 150 mm nominal inner dia. Pipes. 1.00 m 6822.70 One Running 6823.00
Metre
18.10 Providing and fixing G.I. pipes complete with G.I. fittings
and clamps, i/c cutting and making good the walls etc. :
Internal work – Exposed on wall.
18.10.1 15 mm dia. nominal bore 1.00 m 366.40 One Running 366.00
Metre
18.10.2 20 mm dia. nominal bore 1.00 m 437.30 One Running 437.00
Metre
18.10.3 25 mm dia. nominal bore 1.00 m 551.70 One Running 552.00
Metre
18.10.4 32 mm dia. nominal bore 1.00 m 667.00 One Running 667.00
Metre
18.10.5 40 mm dia. nominal bore 1.00 m 811.90 One Running 812.00
Metre
18.10.6 50 mm dia. nominal bore 1.00 m 1048.35 One Running 1048.00
Metre
18.11 Providing and fixing G.I. Pipes complete with G.I. fittings
and clamps, i/c making good the walls etc. concealed
pipe, including painting with anticorrosive bitumastic
paint, cutting chases and making good the wall:

18.11.1 15 mm dia. nominal bore 1.00 m 580.45 One Running 580.00

Metre
18.11.2 20 mm dia. nominal bore 1.00 m 635.20 One Running 635.00
Metre
18.12 Providing and fixing G.I. pipes complete with G.I. fittings
including trenching and refilling etc. : External work

DSR - 2023 IN MS EXCEL Page 170 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.12.1 15 mm dia. nominal bore 1.00 m 322.15 One Running 322.00
Metre
18.12.2 20 mm dia. nominal bore 1.00 m 368.60 One Running 369.00
Metre
18.12.3 25 mm dia. nominal bore 1.00 m 467.75 One Running 468.00
Metre
18.12.4 32 mm dia. nominal bore 1.00 m 540.30 One Running 540.00
Metre
18.12.5 40 mm dia. nominal bore 1.00 m 617.05 One Running 617.00
Metre
18.12.6 50 mm dia. nominal bore 1.00 m 762.15 One Running 762.00
Metre
18.12.7 65 mm dia. nominal bore 1.00 m 896.60 One Running 897.00
Metre
18.12.8 80 mm dia. nominal bore 1.00 m 1041.70 One Running 1042.00
Metre
18.13 Making connection of G.I. distribution branch with G.I.
main of following sizes by providing and fixing tee,
including cutting and threading the pipe etc. complete :

18.13.1 25 to 40 mm nominal bore 1.00 No. 911.90 Each 912.00

18.13.2 50 to 80 mm nominal bore 1.00 No. 1785.35 Each 1785.00
18.14 Fixing water meter and stop cock in G.I. pipe line 1.00 No. 812.30 Each 812.00
including cutting and threading the pipe and making
long screws etc. complete (cost of water meter and
stop cock to be paid separately).

18.15 Providing and fixing brass bib cock of approved quality :

18.15.1 15 mm nominal bore 1.00 No. 353.25 Each 353.00

18.15.2 20 mm nominal bore 1.00 No. 379.20 Each 379.00
18.16 Providing and fixing brass stop cock of approved
quality :
18.16.1 15 mm nominal bore 1.00 No. 353.25 Each 353.00
18.16.2 20 mm nominal bore 1.00 No. 379.20 Each 379.00
18.17 Providing and fixing gun metal gate valve with C.I.
wheel of approved quality (screwed end) :
18.17.1 25 mm nominal bore 1.00 No. 622.40 Each 622.00
18.17.1A 20 mm nominal bore 1.00 No. 539.95 Each 540.00
18.17.2 32 mm nominal bore. 1.00 No. 689.60 Each 690.00
18.17.3 40 mm nominal bore 1.00 No. 826.10 Each 826.00
18.17.4 50 mm nominal bore 1.00 No. 1026.65 Each 1027.00
18.17.5 65 mm nominal bore 1.00 No. 1742.15 Each 1742.00
18.17.6 80 mm nominal bore 1.00 No. 2604.55 Each 2605.00
18.18 Providing and fixing ball valve (brass) of approved
quality, High or low pressure, with plastic floats
complete :
18.18.1 15 mm nominal bore 1.00 No. 406.85 Each 407.00
18.18.2 20 mm nominal bore 1.00 No. 462.50 Each 463.00
18.18.3 25 mm nominal bore 1.00 No. 464.05 Each 464.00
18.19 Providing and fixing gun metal non- return valve of
approved quality (screwed end) :
18.19.1 25 mm nominal bore
18.19.1.1 Horizontal 1.00 No. 591.40 Each 591.00
18.19.1.2 Vertical 1.00 No. 624.10 Each 624.00
18.19.2 32 mm nominal bore
18.19.2.1 Horizontal 1.00 No. 791.90 Each 792.00
18.19.2.2 Vertical 1.00 No. 850.25 Each 850.00
18.19.3 40 mm nominal bore
18.19.3.1 Horizontal 1.00 No. 952.60 Each 953.00

DSR - 2023 IN MS EXCEL Page 171 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.19.3.2 Vertical 1.00 No. 1134.70 Each 1135.00
18.19.4 50 mm nominal bore
18.19.4.1 Horizontal 1.00 No. 1371.20 Each 1371.00
18.19.4.2 Vertical 1.00 No. 1445.15 Each 1445.00
18.19.5 65 mm nominal bore
18.19.5.1 Horizontal 1.00 No. 2448.05 Each 2448.00
18.19.5.2 Vertical 1.00 No. 2291.55 Each 2292.00
18.19.6 80 mm nominal bore
18.19.6.1 Horizontal 1.00 No. 3664.75 Each 3665.00
18.19.6.2 Vertical 1.00 No. 3855.40 Each 3855.00
18.20 Providing and fixing brass ferrule with C.I. mouth cover
including boring and tapping the main :
18.20.1 15 mm nominal bore 1.00 No. 329.30 Each 329.00
18.20.2 20 mm nominal bore 1.00 No. 380.00 Each 380.00
18.20.3 25 mm nominal bore 1.00 No. 486.80 Each 487.00
18.21 Providing and fixing uplasticised PVC connection pipe
with brass unions :
18.21.1 30 cm length
18.21.1.1 15 mm nominal bore 1.00 No. 85.00 Each 85.00
18.21.1.2 20 mm nominal bore 1.00 No. 93.55 Each 94.00
18.21.2 45 cm length
18.21.2.1 15 mm nominal bore 1.00 No. 97.75 Each 98.00
18.21.2.2 20 mm nominal bore 1.00 No. 119.05 Each 119.00
18.22 Providing and fixing C.P. brass shower rose with 15 or
20 mm inlet :
18.22.1 100 mm diameter 1.00 No. 193.95 Each 194.00
18.22.2 150 mm diameter 1.00 No. 222.35 Each 222.00
18.23 Laying in position centrifugally cast (spun) iron S&S or 1.00 Qtl 361.65 One Quintal 362.00
flanged pipes (excluding cost of pipe)
18.24 Laying in position S&S or flanged C.I. special such as 1.00 Qtl 661.85 One Quintal 662.00
tees, bends, collars, tapers and caps etc.(excluding cost
of specials).
18.25 Providing and laying S&S C.I. standard specials such as
tees, bends, collars, tapers, caps etc. (Heavy class) :

18.25.1 Up to 300 mm dia. 1.00 Qtl 6352.40 One Quintal 6352.00

18.25.2 Over 300 mm dia. 1.00 Qtl 6352.40 One Quintal 6352.00
18.26 Providing and laying flanged C.I. standard specials such
as tees, bends, collars, tapers, caps etc., suitable for
flanged jointing as per IS : 1538 :
18.26.1 Up to 300 mm dia. 1.00 Qtl 8913.15 One Quintal 8913.00
18.26.2 Over 300 mm dia. 1.00 Qtl 8486.35 One Quintal 8486.00
18.27 Providing and laying S&S centrifugally cast (spun) iron
pipes (Class LA) conforming to IS - 1536 :
18.27.1 100 mm dia. pipe 1.00 m 1423.10 One Running 1423.00
Metre
18.27.2 125 mm dia. pipe 1.00 m 1729.35 One Running 1729.00
Metre
18.27.3 150 mm dia. pipe 1.00 m 2037.00 One Running 2037.00
Metre
18.27.4 200 mm dia. pipe 1.00 m 3406.85 One Running 3407.00
Metre
18.27.5 250 mm dia. pipe 1.00 m 4639.80 One Running 4640.00
Metre
18.27.6 300 mm dia. pipe 1.00 m 6128.65 One Running 6129.00
Metre
18.27.7 350 mm dia. pipe 1.00 m 7343.80 One Running 7344.00
Metre

DSR - 2023 IN MS EXCEL Page 172 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.27.8 400 mm dia. pipe 1.00 m 9701.00 One Running 9701.00
Metre
18.27.9 450 mm dia. pipe 1.00 m 11714.85 One Running 11715.00
Metre
18.27.10 500 mm dia. pipe 1.00 m 13728.75 One Running 13729.00
Metre
18.27.11 600 mm dia. pipe 1.00 m 18636.45 One Running 18636.00
Metre
18.28 Providing lead caulked joints to spun iron or C.I. pipes
and specials, including testing of joints but excluding
the cost of pig lead :
18.28.1 100 mm diameter pipe 1.00 No. 496.40 Each 496.00
18.28.2 125 mm diameter pipe 1.00 No. 737.50 Each 738.00
18.28.3 150 mm diameter pipe 1.00 No. 744.85 Each 745.00
18.28.4 200 mm diameter pipe 1.00 No. 990.20 Each 990.00
18.28.5 250 mm diameter pipe 1.00 No. 1237.80 Each 1238.00
18.28.6 300 mm diameter pipe 1.00 No. 1488.80 Each 1489.00
18.28.7 350 mm diameter pipe 1.00 No. 1513.60 Each 1514.00
18.28.8 400 mm diameter pipe 1.00 No. 1993.75 Each 1994.00
18.28.9 450 mm diameter pipe 1.00 No. 2238.45 Each 2238.00
18.28.10 500 mm diameter pipe 1.00 No. 2366.45 Each 2366.00
18.28.11 600 mm diameter pipe 1.00 No. 3211.40 Each 3211.00
18.29 Supplying pig lead at site of work. 1.00 Qtl 29875.40 One Quintal 29875.00
18.30 Providing flanged joints to double flanged C.I./ D.I.
pipes and specials, including testing of joints :
18.30.1 80 mm diameter pipe 1.00 No. 215.10 Each 215.00
18.30.2 100 mm diameter pipe 1.00 No. 332.00 Each 332.00
18.30.3 125 mm diameter pipe 1.00 No. 351.90 Each 352.00
18.30.4 150 mm diameter pipe 1.00 No. 387.40 Each 387.00
18.30.5 200 mm diameter pipe 1.00 No. 428.65 Each 429.00
18.30.6 250 mm diameter pipe 1.00 No. 596.65 Each 597.00
18.30.7 300 mm diameter pipe 1.00 No. 599.50 Each 600.00
18.30.8 350 mm diameter pipe 1.00 No. 762.90 Each 763.00
18.30.9 400 mm diameter pipe 1.00 No. 1066.80 Each 1067.00
18.30.10 450 mm diameter pipe 1.00 No. 1305.60 Each 1306.00
18.30.11 500 mm diameter pipe 1.00 No. 1437.80 Each 1438.00
18.30.12 600 mm diameter pipe 1.00 No. 1704.10 Each 1704.00
18.31 Providing and fixing C.I. sluice valves (with cap)
complete with bolts, nuts, rubber insertions etc. (the
tail pieces if required will be paid separately) :
18.31.1 100 mm diameter
18.31.1.1 Class I 1.00 No. 4791.20 Each 4791.00
18.31.1.2 Class II 1.00 No. 4985.85 Each 4986.00
18.31.2 125 mm diameter
18.31.2.1 Class I 1.00 No. 5160.80 Each 5161.00
18.31.2.2 Class II 1.00 No. 5943.00 Each 5943.00
18.31.3 150 mm diameter
18.31.3.1 Class I 1.00 No. 6966.55 Each 6967.00
18.31.3.2 Class II 1.00 No. 7312.40 Each 7312.00
18.31.4 200 mm diameter
18.31.4.1 Class I 1.00 No. 13554.70 Each 13555.00
18.31.4.2 Class II 1.00 No. 14622.95 Each 14623.00
18.31.5 250 mm diameter
18.31.5.1 Class I 1.00 No. 19566.55 Each 19567.00
18.31.5.2 Class II 1.00 No. 24623.50 Each 24624.00
18.31.6 300 mm diameter
18.31.6.1 Class I 1.00 No. 27059.30 Each 27059.00
18.31.6.2 Class II 1.00 No. 30203.00 Each 30203.00

DSR - 2023 IN MS EXCEL Page 173 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.32 Constructing masonry Chamber 30x30x50 cm inside, in
brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for stop cock, with C. I. surface box 100x100 x75
mm (inside) with hinged cover fixed in reinforced
cement concrete slab 1:1.5:3 mix (1 cement 1.5 coarse
sand : 3 graded stone aggregate 20 mm nominal size),
i/c necessary excavation, foundation concrete 1:5:10 (1
cement: 5 fine sand : 10 graded stone aggregate 40mm
nominal size) and inside plastering with cement mortar
1:3 (1 cement: 3 coarse sand) 12mm thick, finished with
a floating coat of neat cement complete as per standard
design :

18.32.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 No. 1992.60 Each 1993.00
class designation 7.5
18.33 Constructing masonry Chamber 60x60x75 cm inside, in
brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.l. surface box 100mm top
diameter, 160 mm bottom diameter and 180 mm deep
(inside) with chained lid and RCC top slab 1:1.5:3 mix (1
cement : 1.5 coarse sand : 3 graded stone aggregate
20mm nominal size ), i/c necessary excavation,
foundation concrete 1:5:10 (1 cement : 5 fine sand : 10
graded stone aggregate 40 mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat
cement complete as per standard design:

18.33.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 No. 10862.40 Each 10862.00
class designation 7.5
18.34 Constructing masonry Chamber 90x90x100 cm inside, in
brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.l. surface box 100mm top
diameter, 160 mm bottom diameter and 180 mm deep
(inside) with chained lid and RCC top slab 1:1.5:3 mix (1
cement : 1.5 coarse sand : 3 graded stone aggregate
20mm nominal size ), i/c necessary excavation,
foundation concrete 1:5:10 (1 cement : 5 fine sand : 10
graded stone aggregate 40 mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat
cement complete as per standard design:

18.34.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 No. 18896.70 Each 18897.00
class designation 7.5
18.35 Constructing masonry Chamber 120x120x100 cm inside,
in brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.l. surface box 100mm top
diameter, 160 mm bottom diameter and 180 mm deep
(inside) with chained lid and RCC top slab 1:1.5:3 mix (1
cement : 1.5 coarse sand : 3 graded stone aggregate
20mm nominal size ), i/c necessary excavation,
foundation concrete 1:5:10 (1 cement : 5 fine sand : 10
graded stone aggregate 40 mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat
cement complete as per standard design:

DSR - 2023 IN MS EXCEL Page 174 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.35.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 No. 26163.40 Each 26163.00
class designation 7.5
18.36 Constructing masonry Chamber 60x60x75 cm, inside in
brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for fire hydrants, with C.l. surface box 350x350
mm top and 165 mm deep (inside) with chained lid and
RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand 3
graded stone aggregate 20 mm nominal size) , i/c
necessary excavation, foundation concrete 1:5:10 (1
cement: 5 fine sand:10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar
1:3 (1 cement: 3 coarse sand) 12 mm thick, finished
with a floating coat of neat cement complete as per
standard design:

18.36.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 No. 10354.95 Each 10355.00
class designation 7.5
18.37 Constructing masonry Chamber 60x45x50 cm inside, in
brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for water meter complete with C.l. double flap
surface box 400x200x200 mm (inside) with locking
arrangement and RCC top slab 1:1.5:3 mix (1 cement :
1.5 coarse sand : 3 graded stone aggregate 20 mm
nominal size) , i/c necessary excavation, foundation
concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded
stone aggregate 40 mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat
cement complete as per standard design :

18.37.1 With common burnt clay F.P.S.(non modular) bricks of 1.00 No. 9698.55 Each 9699.00
class designation 7.5
18.38 Painting G.I. pipes and fittings with synthetic enamel
white paint with two coats over a ready mixed priming
coat, both of approved quality for new work :

18.38.1 15 mm diameter pipe. 1.00 m 19.40 One Running 19.00

Metre
18.38.2 20 mm diameter pipe. 1.00 m 23.25 One Running 23.00
Metre
18.38.3 25 mm diameter pipe. 1.00 m 30.25 One Running 30.00
Metre
18.38.4 32 mm diameter pipe. 1.00 m 36.35 One Running 36.00
Metre
18.38.5 40 mm diameter pipe. 1.00 m 42.65 One Running 43.00
Metre
18.38.6 50 mm diameter pipe. 1.00 m 51.00 One Running 51.00
Metre
18.39 Repainting G.I. pipes and fittings with synthetic enamel
white paint with one coat of approved quality :

18.39.1 15 mm diameter pipe. 1.00 m 9.50 One Running 10.00

Metre
18.39.2 20 mm diameter pipe. 1.00 m 11.30 One Running 11.00
Metre
18.39.3 25 mm diameter pipe 1.00 m 14.40 One Running 14.00
Metre
18.39.4 32 mm diameter pipe 1.00 m 17.25 One Running 17.00
Metre

DSR - 2023 IN MS EXCEL Page 175 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.39.5 40 mm diameter pipe 1.00 m 20.00 One Running 20.00
Metre
18.39.6 50 mm diameter pipe 1.00 m 23.85 One Running 24.00
Metre
18.39.7 65 mm diameter pipe 1.00 m 37.85 One Running 38.00
Metre
18.39.8 80 mm diameter pipe 1.00 m 44.00 One Running 44.00
Metre
18.40 Painting G.I. pipes and fittings with two coats of anti-
corrosive bitumastic paint of approved quality :
18.40.1 15 mm diameter pipe 1.00 m 12.05 One Running 12.00
Metre
18.40.2 20 mm diameter pipe 1.00 m 14.45 One Running 14.00
Metre
18.40.3 25 mm diameter pipe 1.00 m 18.35 One Running 18.00
Metre
18.40.4 32 mm diameter pipe 1.00 m 22.20 One Running 22.00
Metre
18.40.5 40 mm diameter pipe 1.00 m 25.25 One Running 25.00
Metre
18.40.6 50 mm diameter pipe 1.00 m 30.50 One Running 31.00
Metre
18.40.7 65 mm diameter pipe 1.00 m 37.85 One Running 38.00
Metre
18.40.8 80 mm diameter pipe 1.00 m 44.00 One Running 44.00
Metre
18.41 Providing and filling sand of grading zone V or coarser
grade all- round the G.I. pipes in external work.

18.41.1 15 mm diameter pipe 1.00 m 154.45 One Running 154.00

Metre
18.41.2 20 mm diameter pipe 1.00 m 156.55 One Running 157.00
Metre
18.41.3 25 mm diameter pipe 1.00 m 160.70 One Running 161.00
Metre
18.41.4 32 mm diameter pipe 1.00 m 164.90 One Running 165.00
Metre
18.41.5 40 mm diameter pipe 1.00 m 167.00 One Running 167.00
Metre
18.41.6 50 mm diameter pipe 1.00 m 173.25 One Running 173.00
Metre
18.41.7 65 mm diameter pipe 1.00 m 273.45 One Running 273.00
Metre
18.41.8 80 mm diameter pipe 1.00 m 281.80 One Running 282.00
Metre
18.41.9 100 mm diameter pipe 1.00 m 298.50 One Running 299.00
Metre
18.41.10 150 mm diameter pipe 1.00 m 444.60 One Running 445.00
Metre
18.42 Boring with 100 mm diameter casing pipe for hand
pump / tube well, in all soils except ordinary hard rocks
requiring blasting, including removing the casing pipe
after the hand pump / tube well is lowered and tested :

18.42.1 Up to 6 metres depth. 1.00 m 747.90 One Running 748.00

Metre
18.42.2 Beyond 6 m and up to 12 m depth. 1.00 m 884.85 One Running 885.00
Metre

DSR - 2023 IN MS EXCEL Page 176 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.42.3 Beyond 12 m and up to 18 m depth. 1.00 m 1025.95 One Running 1026.00
Metre
18.43 Providing and placing in position filters of 40 mm 1.00 m 960.30 One Running 960.00
diameter G.I. pipe with brass strainer of approved Metre
quality.
18.44 Providing and fixing to filter and lowering to proper 1.00 m 546.00 One Running 546.00
levels 40 mm G.I. pipe for tube well including cleaning Metre
and priming the tube well.
18.45 Providing and placing in position hand pump of 1.00 No. 1321.65 Each 1322.00
approved quality for 40 mm diameter G.I. pipe
complete with all accessories.
18.46 Providing and fixing G.I. Union in G.I. pipe including
cutting and threading the pipe and making long screws
etc. complete (New work)
18.46.1 15 mm nominal bore 1.00 No. 318.35 Each 318.00
18.46.2 20 mm nominal bore 1.00 No. 346.80 Each 347.00
18.46.3 25 mm nominal bore 1.00 No. 439.25 Each 439.00
18.46.4 32 mm nominal 1.00 No. 489.05 Each 489.00
18.46.5 40 mm nominal bore 1.00 No. 631.30 Each 631.00
18.46.6 50mm nominal bore 1.00 No. 823.80 Each 824.00
18.46.7 65mm nominal bore 1.00 No. 1136.80 Each 1137.00
18.46.8 80 mm nominal bore

1.00 No. 1207.95 Each 1208.00

18.47 Providing and fixing G.I. Union in existing G.I. pipe line,
cutting and threading the pipe and making long screws
including excavation, refilling the earth or cutting of
wall and making good the same complete wherever
required :

18.47.1 15 mm nominal bore. 1.00 No. 829.45 Each 829.00

18.47.2 20 mm nominal bore. 1.00 No. 857.85 Each 858.00
18.47.3 25 mm nominal bore. 1.00 No. 950.35 Each 950.00
18.47.4 32 mm nominal bore. 1.00 No. 1000.15 Each 1000.00
18.47.5 40 mm nominal bore. 1.00 No. 1142.40 Each 1142.00
18.47.6 50 mm nominal bore. 1.00 No. 1520.80 Each 1521.00
18.47.7 65 mm nominal bore. 1.00 No. 1833.75 Each 1834.00
18.47.8 80 mm nominal bore. 1.00 No. 1904.90 Each 1905.00
18.48 Providing and placing on terrace (at all floor levels) 1.00 Ltr 11.00 One Litre 11.00
polyethylene water storage tank, IS : 12701 marked,
with cover and suitable locking arrangement and
making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank.

18.48A Providing and fixing rectangular high density 1.00 Ltr 11.00 One Litre 11.00
polyethylene water storage loft tank with cover,
conforming to ISI : 12701, colour of opaque white or as
approved by Engineer-in-charge. The rate
includesmaking necessary holes for inlet, outlet & over
flow pipes. The base support i/c fittings & fixtures for
tank shall be paid separately.

18.49 Providing and fixing C.P. brass bib cock of approved

quality conforming to IS:8931:
18.49.1 15 mm nominal bore. 1.00 No. 506.80 Each 507.00
18.50 Providing and fixing C.P. brass long nose bib cock of
approved quality conforming to IS standards and
weighing not less than 810 gms.
18.50.1 15 mm nominal bore. 1.00 No. 820.70 Each 821.00

DSR - 2023 IN MS EXCEL Page 177 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.51 Providing and fixing C.P. brass long body bib cock of
approved quality conforming to IS standards and
weighing not less than 690 gms.
18.51.1 15 mm nominal bore 1.00 No. 798.95 Each 799.00
18.52 Providing and fixing C.P. brass stop cock (concealed) of
standard design and of approved make conforming to
IS:8931.
18.52.1 15 mm nominal bore. 1.00 No. 670.45 Each 670.00
18.53 Providing and fixing C.P. brass angle valve for basin
mixer and geyser points of approved quality conforming
to IS:8931 :
18.53.1 15mm nominal bore 1.00 No. 574.30 Each 574.00
18.53A Providing and fixing C.P. Brass extension nipple (size 1.00 No. 74.80 Each 75.00
15mmx50mm) of approved make and quality as per
direction of Engineer-in-charge.
18.54 Providing and fixing PTMT bib cock of approved quality
and colour.
18.54.1 15mm nominal bore, 86 mm long. Weighing not less 1.00 No. 125.60 Each 126.00
than 88 gms.
18.54.2 15 mm nominal bore, 122 mm long. Weighing not less 1.00 No. 161.20 Each 161.00
than 99 gms.
18.54.3 15 mm nominal bore, 165 mm long. Weighing not less 1.00 No. 176.85 Each 177.00
than 110 gms.
18.54.4 15mm nominal bore, 90 mm long. Weighing not less 1.00 No. 196.75 Each 197.00
than 93 gms.
18.55 Providing and fixing PTMT stop cock of approved quality
and colour.
18.55.1 15 mm nominal bore, 86 mm long. Weighing not less 1.00 No. 118.50 Each 119.00
than 88 gms.
18.55.2 20mm nominal bore, 89 mm long. Weighing not less 1.00 No. 129.90 Each 130.00
than 88 gms.
18.55.3 Concealed stop cock, 15 mm nominal bore, 108mm 1.00 No. 218.10 Each 218.00
long. Weighing not less than 108 gms.
18.56 Providing and fixing PTMT pillar cock of approved
quality and colour .
18.56.1 15mm nominal bore, 107 mm long. Weighing not less 1.00 No. 208.45 Each 208.00
than 110 gms.
18.56.2 15mm nominal bore, 125 mm long foam flow. Weighing 1.00 No. 224.10 Each 224.00
not less than 120 gms.
18.57 Providing and fixing PTMT, push cock of approved
quality and colour.
18.57.1 15 mm nominal bore, 98 mm long. Weighing not less 1.00 No. 112.80 Each 113.00
than 75 gms.
18.57.2 15 mm nominal bore, 80 mm long. Weighing not less 1.00 No. 95.75 Each 96.00
than 46 gms.
18.58 Providing and fixing PTMT grating of approved quality
and colour.
18.58.1 Circular type.
18.58.1.1 100 mm nominal dia. 1.00 No. 37.60 Each 38.00
18.58.1.2 125 mm nominal dia with 25 mm waste hole. 1.00 No. 51.85 Each 52.00
18.58.2 Rectangular type with openable circular lid.
18.58.2.1 150 mm nominal size square 100 mm diameter of the 1.00 No. 196.95 Each 197.00
inner hinged round grating.
18.59 Providing and fixing C.I. double acting air valve of
approved quality with bolts, nuts, rubber insertions etc.
complete (The tail pieces, tapers etc if required will be
paid separately) :

18.59.1 50 mm dia 1.00 No. 5748.80 Each 5749.00

18.59.2 80 mm dia 1.00 No. 6993.60 Each 6994.00

DSR - 2023 IN MS EXCEL Page 178 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.59.3 100 mm dia 1.00 No. 8893.00 Each 8893.00
18.60 Providing and fixing enclosed type water meter (bulk
type) conforming to IS : 2373 and tested by Municipal
Board complete with bolts, nuts, rubber insertions etc.
(The tail pieces if required will be paid separately) :

18.60.1 80 mm dia nominal bore 1.00 No. 3627.65 Each 3628.00

18.60.2 100 mm dia nominal bore 1.00 No. 5468.35 Each 5468.00
18.60.3 150 mm dia nominal bore 1.00 No. 8408.80 Each 8409.00
18.60.4 200 mm dia nominal bore 1.00 No. 9043.30 Each 9043.00
18.61 Providing and fixing C.I. dirt box strainer for bulk type
water meter with nuts, bolts, rubber insertions etc.
complete conforming to IS : 2373 :
18.61.1 80 mm dia 1.00 No. 4623.50 Each 4624.00
18.61.2 100 mm dia. 1.00 No. 7460.00 Each 7460.00
18.61.3 150 mm dia 1.00 No. 9433.10 Each 9433.00
18.61.4 200 mm dia 1.00 No. 12927.10 Each 12927.00
18.62 Providing and fixing PTMT Ball cock of approved quality,
colour and make complete with Epoxy coated
aluminium rod with L.P./ H.P.H.D. plastic ball.
18.62.1 15 mm nominal bore, 105 mm long. Weighing not less 1.00 No. 182.10 Each 182.00
than 138 gms.
18.62.2 20 mm nominal bore, 120 mm long. Weighing not less 1.00 No. 257.60 Each 258.00
than 198 gms.
18.62.3 25 mm nominal bore, 152 mm long. Weighing not less 1.00 No. 523.80 Each 524.00
than 440 gms.
18.62.4 40mm nominal bore, 206mm long. Weighing not less 1.00 No. 737.20 Each 737.00
than 690 gms.
18.62.5 50mm nominal bore, 242 mm long. Weighing not less 1.00 No. 1375.95 Each 1376.00
than 1240 gms.
18.63 Providing and fixing PTMT angle stop cock 15 mm 1.00 No. 156.90 Each 157.00
nominal bore. Weighing not less than 85 gms.
18.64 Providing and fixing PTMT swivelling shower, 15mm 1.00 No. 121.40 Each 121.00
nominal bore. Weighing not less than 40 gms.
18.65 Providing and fixing PTMT soap Dish Holder having 1.00 No. 111.45 Each 111.00
length of 138 mm, breadth 102 mm, height of 75 mm
with concealed fitting arrangements. Weighing not less
than 106 gms.

18.66 Providing and laying S&S C.I. Standard specials such as

tees, bends, collars tapers and caps etc, suitable for
flanged jointing as per IS :1538:
18.66.1 Up to 300 mm dia 1.00 Qtl 8628.60 One Quintal 8629.00
18.66.2 Above 300 mm dia 1.00 Qtl 10157.95 One Quintal 10158.00
18.67 Providing and laying S&S C.I. Standard specials suitable
for mechanical jointing as per IS : 13382 :
18.67.1 Up to 300 mm dia 1.00 Qtl 13764.35 One Quintal 13764.00
18.67.2 Above 300 mm dia 1.00 Qtl 14532.55 One Quintal 14533.00
18.68 Providing and laying D.I. specials of class K-12 suitable
for push-on jointing as per IS : 9523 :
18.68.1 Up to 600 mm dia 1.00 Qtl 20009.70 One Quintal 20010.00
18.68.2 Above 600 mm dia 1.00 Qtl 26696.10 One Quintal 26696.00
18.68A Providing and laying Class K-12 Ductile Iron double
chamber restrained joint (bolt less) specials such as
tees, bends, collars, tapers and caps etc. conforming to
IS 9523 including testing of joints all complete :

18.68A.1 Up to 600 mm dia 1.00 Qtl 30394.95 One Quintal 30395.00

18.68A.2 Above 600 mm dia 1.00 Qtl 39073.05 One Quintal 39073.00
18.69 Providing and laying D.I. Specials of Class K - 12 suitable
for mechanical jointing as per IS : 9523 :

DSR - 2023 IN MS EXCEL Page 179 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.69.1 Up to 600 mm dia 1.00 Qtl 21290.10 One Quintal 21290.00
18.69.2 Above 600 mm dia 1.00 Qtl 28403.25 One Quintal 28403.00
18.70 Providing push-on-joints to Centrifugally (Spun) Cast
Iron Pipes or Ductile Iron Pipes including testing of
joints and the cost of rubber gasket :
18.70.1 100 mm dia pipes 1.00 joint 119.45 One Joint 119.00
18.70.2 150 mm dia pipes 1.00 joint 192.85 One Joint 193.00
18.70.3 200 mm dia pipes 1.00 joint 280.85 One Joint 281.00
18.70.4 250 mm dia pipes 1.00 joint 340.35 One Joint 340.00
18.70.5 300 mm dia pipes 1.00 joint 435.45 One Joint 435.00
18.70.6 350 mm dia pipes 1.00 joint 495.00 One Joint 495.00
18.70.7 400 mm dia pipes 1.00 joint 696.80 One Joint 697.00
18.70.8 450 mm dia pipes 1.00 joint 820.35 One Joint 820.00
18.70.9 500 mm dia pipes 1.00 joint 871.45 One Joint 871.00
18.70.10 600 mm dia pipes 1.00 joint 1207.90 One Joint 1208.00
18.70.11 700 mm dia pipes 1.00 joint 1572.70 One Joint 1573.00
18.70.12 750 mm dia pipes 1.00 joint 1693.65 One Joint 1694.00
18.70.13 800 mm dia a pipes 1.00 joint 1844.40 One Joint 1844.00
18.70.14 900 mm dia pipes 1.00 joint 2314.65 One Joint 2315.00
18.70.15 1000 mm dia pipes 1.00 joint 2604.40 One Joint 2604.00
18.71 Providing and laying Double Flanged (screwed/ welded)
Centrifugally (Spun) Cast Iron, Class B (IS : 1536) :

18.71.1 100 mm dia C.I. Double Flanged Pipe 1.00 m 2089.35 One Running 2089.00
Metre
18.71.2 150 mm dia C.I. Double Flanged Pipe 1.00 m 3218.50 One Running 3219.00
Metre
18.71.3 200 mm dia C.I. Double Flanged Pipe 1.00 m 4995.85 One Running 4996.00
Metre
18.71.4 250 mm dia C.I. Double Flanged Pipe 1.00 m 6227.00 One Running 6227.00
Metre
18.71.5 300 mm dia C.I. Double Flanged Pipe 1.00 m 8094.30 One Running 8094.00
Metre
18.71.6 350 mm dia C.I. Double Flanged Pipe 1.00 m 10093.90 One Running 10094.00
Metre
18.71.7 400 mm dia C.I. Double Flanged Pipe 1.00 m 13136.65 One Running 13137.00
Metre
18.71.8 450 mm dia C.I. Double Flanged Pipe 1.00 m 16769.30 One Running 16769.00
Metre
18.71.9 500 mm dia C.I. Double Flanged Pipe 1.00 m 21619.65 One Running 21620.00
Metre
18.71.10 600 mm dia C.I. Double Flanged Pipe 1.00 m 27459.40 One Running 27459.00
Metre
18.72 Providing and laying S&S Centrifugally Cast (Spun) /
Ductile Iron Pipes conforming to IS : 8329 :
18.72.1 100 mm dia Ductile Iron Class K-7 pipes 1.00 m 1257.80 One Running 1258.00
Metre
18.72.2 150 mm dia Ductile Iron Class K-7 pipes 1.00 m 1789.60 One Running 1790.00
Metre
18.72.3 200 mm dia Ductile Iron Class K-7 pipes 1.00 m 2328.15 One Running 2328.00
Metre
18.72.4 250 mm dia Ductile Iron Class K-7 pipes 1.00 m 2880.70 One Running 2881.00
Metre
18.72.5 300 mm dia Ductile Iron Class K-7 pipes 1.00 m 3518.25 One Running 3518.00
Metre
18.72.6 350 mm dia Ductile Iron Class K-7 pipes 1.00 m 4186.50 One Running 4187.00
Metre
18.72.7 400 mm dia Ductile Iron Class K-7 pipes 1.00 m 5084.55 One Running 5085.00
Metre

DSR - 2023 IN MS EXCEL Page 180 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.72.8 450 mm dia Ductile Iron Class K-7 pipes 1.00 m 6163.35 One Running 6163.00
Metre
18.72.9 500 mm dia Ductile Iron Class K-7 pipes 1.00 m 6787.40 One Running 6787.00
Metre
18.72.10 600 mm dia Ductile Iron Class K-7 pipes 1.00 m 8965.95 One Running 8966.00
Metre
18.72.11 700 mm dia Ductile Iron Class K-7 pipes 1.00 m 11566.35 One Running 11566.00
Metre
18.72.12 800 mm dia Ductile Iron Class K-7 pipes 1.00 m 14609.05 One Running 14609.00
Metre
18.72.13 900 mm dia Ductile Iron Class K-7 pipes 1.00 m 18734.20 One Running 18734.00
Metre
18.72.14 1000 mm dia Ductile Iron Class K-7 pipes 1.00 m 19895.80 One Running 19896.00
Metre
18.72.15 100 mm dia Ductile Iron Class K-9 pipes 1.00 m 1344.60 One Running 1345.00
Metre
18.72.16 150 mm dia Ductile Iron Class K-9 pipes 1.00 m 1837.75 One Running 1838.00
Metre
18.72.17 200 mm dia Ductile Iron Class K-9 pipes 1.00 m 2478.14 One Running 2478.00
Metre
18.72.18 250 mm dia Ductile Iron Class K-9 pipes 1.00 m 3516.80 One Running 3517.00
Metre
18.72.19 300 mm dia Ductile Iron Class K-9 pipes 1.00 m 4344.40 One Running 4344.00
Metre
18.72.20 350 mm dia Ductile Iron Class K-9 pipes 1.00 m 5409.85 One Running 5410.00
Metre
18.72.21 400 mm dia Ductile Iron Class K-9 pipes 1.00 m 6844.30 One Running 6844.00
Metre
18.72.22 450 mm dia Ductile Iron Class K-9 pipes 1.00 m 7976.85 One Running 7977.00
Metre
18.72.23 500 mm dia Ductile Iron Class K-9 pipes 1.00 m 9679.85 One Running 9680.00
Metre
18.72.24 600 mm dia Ductile Iron Class K-9 pipes 1.00 m 12986.95 One Running 12987.00
Metre
18.72.25 700 mm dia Ductile Iron Class K-9 pipes 1.00 m 17431.60 One Running 17432.00
Metre
18.72.26 750 mm dia Ductile Iron Class K-9 pipes 1.00 m 18567.85 One Running 18568.00
Metre
18.72.27 800 mm dia Ductile Iron Class K-9 pipes 1.00 m 18891.20 One Running 18891.00
Metre
18.72.28 900 mm dia Ductile Iron Class K-9 pipes 1.00 m 23163.00 One Running 23163.00
Metre
18.72.29 1000 mm dia Ductile Iron Class K-9 pipes 1.00 m 25133.00 One Running 25133.00
Metre
18.72A Providing, laying, jointing and testing S&S Centrifugally
Cast Ductile Iron double chamber Class K-9 pressure
pipes conforming to IS 8329:2000 with restrained Joints
(bolt less), all complete.

18.72A.1 100 mm nominal dia pipe 1.00 m 1870.75 One Metre 1871.00
18.72A.2 150 mm nominal dia pipe 1.00 m 2590.90 One Metre 2591.00
18.72A.3 200 mm nominal dia pipe 1.00 m 3260.55 One Metre 3261.00
18.72A.4 250 mm nominal dia pipe 1.00 m 4357.60 One Metre 4358.00
18.72A.5 300 mm nominal dia pipe 1.00 m 5452.95 One Metre 5453.00
18.72A.6 350 mm nominal dia pipe 1.00 m 6636.80 One Metre 6637.00
18.72A.7 400 mm nominal dia pipe 1.00 m 8279.45 One Metre 8279.00
18.72A.8 450 mm nominal dia pipe 1.00 m 9861.20 One Metre 9861.00
18.72A.9 500 mm nominal dia pipe 1.00 m 11628.30 One Metre 11628.00
18.72A.10 600 mm nominal dia pipe 1.00 m 15202.60 One Metre 15203.00
18.72A.11 700 mm nominal dia pipe 1.00 m 19217.15 One Metre 19217.00

DSR - 2023 IN MS EXCEL Page 181 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.72A.12 750 mm nominal dia pipe 1.00 m 21627.85 One Metre 21628.00
18.72A.13 800 mm nominal dia pipe 1.00 m 23932.65 One Metre 23933.00
18.72A.14 900 mm nominal dia pipe 1.00 m 29836.95 One Metre 29837.00
18.72A.15 1000 mm nominal dia pipe 1.00 m 36164.10 One Metre 36164.00
18.73 Providing and laying Double Flanged (Screwed/ Welded)
Centrifugally (Spun) Ductile Iron Pipes of Class K - 9
conforming to IS: 8329 :
18.73.1 100 mm dia Ductile Iron Double Flanged 1.00 m 1821.55 One Running 1822.00
Metre
18.73.2 150 mm dia Ductile Iron Double Flanged 1.00 m 2607.50 One Running 2608.00
Metre
18.73.3 200 mm dia Ductile Iron Double Flanged 1.00 m 3360.80 One Running 3361.00
Metre
18.73.4 250 mm dia Ductile Iron Double Flanged 1.00 m 4696.15 One Running 4696.00
Metre
18.73.5 300 mm dia Ductile Iron Double Flanged 1.00 m 5895.70 One Running 5896.00
Metre
18.73.6 350 mm dia Ductile Iron Double Flanged 1.00 m 7550.45 One Running 7550.00
Metre
18.73.7 400 mm dia Ductile Iron Double Flanged 1.00 m 9744.40 One Running 9744.00
Metre
18.73.8 450 mm dia Ductile Iron Double Flanged 1.00 m 10136.10 One Running 10136.00
Metre
18.73.9 500 mm dia Ductile Iron Double Flanged 1.00 m 15472.95 One Running 15473.00
Metre
18.73.10 600 mm dia Ductile Iron Double Flanged 1.00 m 19925.30 One Running 19925.00
Metre
18.73.11 700 mm dia Ductile Iron Double Flanged 1.00 m 22830.80 One Running 22831.00
Metre
18.74 Providing and fixing unplasticised P.V.C. connection
pipe with PTMT Nuts, collar and bush of approved
quality and colour.
18.74.1 15 mm nominal bore with 30 cm length. 1.00 No. 96.35 Each 96.00
18.74.2 15 mm nominal bore with 45 cm length. 1.00 No. 121.90 Each 122.00
18.75 Providing and fixing PTMT extension nipple for water
tank pipe, fittings of approved quality and colour.
18.75.1 15 mm nominal bore. Weighing not less than 32 gms. 1.00 No. 53.60 Each 54.00
18.75.2 20mm nominal bore. Weighing not less than 40 gms. 1.00 No. 93.45 Each 93.00
18.75.3 25mm nominal bore. Weighing not less than 62 gms. 1.00 No. 113.35 Each 113.00
18.76 Cutting holes up to 30x30 cm in walls including making
good the same:
18.76.1 With common burnt clay F.P.S. (non modular) bricks. 1.00 No. 416.80 Each 417.00
18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs 1.00 No. 452.00 Each 452.00
for passing drain pipe etc. and repairing the hole after
insertion of drain pipe etc. with cement concrete 1:2:4
(1 cement :2 coarse sand : 4 graded stone aggregate 20
mm nominal size), including finishing complete so as to
make it leak proof.

18.78 Making chases up to 7.5x7.5 cm in walls including 1.00 m 202.90 One Running 203.00
making good and finishing with matching surface after Metre
housing G.I. pipe etc.
18.79 Making hole up to 20x20 cm and embedding pipes up 1.00 m 209.20 One Running 209.00
to 150 mm diameter in masonry and filling with cement Metre
concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size)including disposal
of malba.

DSR - 2023 IN MS EXCEL Page 182 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.80 Disinfecting C.I. water mains by flushing with water
containing bleaching powder @ 0.5 gms per litre of
water and cleaning the same with fresh water,
operation to be repeated three times including getting
the sample of water from the disinfected main tested in
the municipal laboratory.

18.80.1 80 mm diameter C.I. pipe 1.00 units 1844.00 100 Metre 1844.00
18.80.2 100 mm diameter C.I. pipe 1.00 units 2415.15 100 Metre 2415.00
18.80.3 125 mm diameter C.I. pipe 1.00 units 3006.40 100 Metre 3006.00
18.80.4 150 mm diameter C.I. pipe 1.00 units 3593.85 100 Metre 3594.00
18.80.5 200 mm diameter C.I. pipe 1.00 units 4771.60 100 Metre 4772.00
18.80.6 250 mm diameter C.I. pipe 1.00 units 5977.65 100 Metre 5978.00
18.80.7 300 mm diameter C.I. pipe 1.00 units 6618.15 100 Metre 6618.00
18.80.8 350 mm diameter C.I. pipe 1.00 units 7272.35 100 Metre 7272.00
18.80.9 400 mm diameter C.I. pipe 1.00 units 7950.85 100 Metre 7951.00
18.80.10 450 mm diameter C.I. pipe 1.00 units 8635.75 100 Metre 8636.00
18.80.11 500 mm diameter C.I. pipe 1.00 units 9351.25 100 Metre 9351.00
18.80.12 600 mm diameter C.I. pipe 1.00 units 10787.45 100 Metre 10787.00
18.81 Extra for every operation of disinfecting the C.I. main by
flushing with water containing bleaching powder @ 0.5
gms per litre of water and cleaning the same with fresh
water, including getting the samples of water tested in
the municipal laboratory:

18.81.1 80 mm diameter C.I. pipe 1.00 units 674.95 100 Metre 675.00
18.81.2 100 mm diameter C.I. pipe 1.00 units 824.95 100 Metre 825.00
18.81.3 125 mm diameter C.I. pipe 1.00 units 1003.95 100 Metre 1004.00
18.81.4 150 mm diameter C.I. pipe 1.00 units 1164.25 100 Metre 1164.00
18.81.5 200 mm diameter C.I. pipe 1.00 units 1753.10 100 Metre 1753.00
18.81.6 250 mm diameter C.I. pipe 1.00 units 2012.75 100 Metre 2013.00
18.81.7 300 mm diameter C.I. pipe 1.00 units 2255.15 100 Metre 2255.00
18.81.8 350 mm diameter C.I. pipe 1.00 units 2632.00 100 Metre 2632.00
18.81.9 400 mm diameter C.I. pipe 1.00 units 3011.20 100 Metre 3011.00
18.81.10 450 mm diameter C.I. pipe 1.00 units 3398.15 100 Metre 3398.00
18.81.11 500 mm diameter C.I. pipe 1.00 units 3787.10 100 Metre 3787.00
18.81.12 600 mm diameter C.I. pipe 1.00 units 4573.95 100 Metre 4574.00
18.82 Dismantling old C.I. pipes including excavation and
refilling trenches after taking out the pipes, breaking
lead caulked joints, melting of lead and making into
blocks including stacking of pipes at site lead upto 50
metre:

18.82.1 80 mm diameter C.I. pipe 1.00 m 315.55 One Running 316.00

Metre
18.82.2 100 mm diameter C.I. pipe 1.00 m 332.50 One Running 333.00
Metre
18.82.3 125 mm diameter C.I. pipe 1.00 m 348.75 One Running 349.00
Metre
18.82.4 150 mm diameter C.I. pipe 1.00 m 365.45 One Running 365.00
Metre
18.82.5 200 mm diameter C.I. pipe 1.00 m 411.50 One Running 412.00
Metre
18.82.6 250 mm diameter C.I. pipe 1.00 m 456.60 One Running 457.00
Metre
18.82.7 300 mm diameter C.I. pipe 1.00 m 497.80 One Running 498.00
Metre
18.82.8 350 mm diameter C.I. pipe 1.00 m 538.00 One Running 538.00
Metre
18.82.9 400 mm diameter C.I. pipe 1.00 m 575.80 One Running 576.00
Metre

DSR - 2023 IN MS EXCEL Page 183 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.82.10 450 mm diameter C.I. pipe 1.00 m 614.30 One Running 614.00
Metre
18.82.11 500 mm diameter C.I. pipe 1.00 m 649.45 One Running 649.00
Metre
18.82.12 600 mm diameter C.I. pipe 1.00 m 713.95 One Running 714.00
Metre
18.83 Labour for cutting C.I. pipe with steel saw.
18.83.1 80 mm diameter C.I. pipe 1.00 nos 145.25 Each cut 145.00
18.83.2 100 mm diameter C.I. pipe 1.00 nos 194.70 Each cut 195.00
18.83.3 125 mm diameter C.I. pipe 1.00 nos 269.80 Each cut 270.00
18.83.4 150 mm diameter C.I. pipe 1.00 nos 365.70 Each cut 366.00
18.83.5 200 mm diameter C.I. pipe 1.00 nos 487.75 Each cut 488.00
18.83.6 250 mm diameter C.I. pipe 1.00 nos 606.85 Each cut 607.00
18.83.7 300 mm diameter C.I. pipe 1.00 nos 728.85 Each cut 729.00
18.83.8 350 mm diameter C.I. pipe 1.00 nos 847.95 Each cut 848.00
18.83.9 400 mm diameter C.I. pipe 1.00 nos 969.55 Each cut 970.00
18.83.10 450 mm diameter C.I. pipe 1.00 nos 1089.10 Each cut 1089.00
18.83.11 500 mm diameter C.I. pipe 1.00 nos 1210.70 Each cut 1211.00
18.83.12 600 mm diameter C.I. pipe 1.00 nos 1445.95 Each cut 1446.00
18.84 Providing & fixing chrome plated brass battery based
infrared sensor operated pillar cock, having foam flow
technology.
18.84.1 15 mm nominal bore. 1.00 No. 8803.70 Each 8804.00
18.85 Providing and fixing Stainless Steel pipe and fitting of
grade AISI 304 as per JIS standard 3448 complete with
press type fitting (fitting shall be paid for separately) i/c
fixing of the pipe with clamps at 1.00 m spacing
including cutting and making good the walls including
testing of joints complete as per direction of Engineer-
in-charge. (The pipe length inserted in the fitting shall
not be measured for payment) Internal work - Exposed
on wall

18.85.1 15.88 mm outer dia Pipe 1.00 m 420.25 One Running 420.00
Metre
18.85.2 22.22 mm outer dia Pipe 1.00 m 599.50 One Running 600.00
Metre
18.85.3 28.58 mm outer dia Pipe 1.00 m 704.55 One Running 705.00
Metre
18.85.4 34.00 mm outer dia Pipe 1.00 m 913.65 One Running 914.00
Metre
18.85.5 42.70 mm outer dia Pipe 1.00 m 943.90 One Running 944.00
Metre
18.85.6 48.60 mm outer dia Pipe 1.00 m 1202.35 One Running 1202.00
Metre
18.85A Providing and fixing stainless Steel pipe and fitting of
grade 316L as per IS 6911:2017 and conforming to EN-
10312 standards complete with press type fitting
( fitting shall be paid for separately) i/c fixing of the pipe
with clamps at 1.00 m spacing including cutting and
making good the walls including testing of joints
complete as per the direction of Engineer- in- charge.
( The pipe length inserted in the fitting shall not be
measure for payment).

18.85A.1 15 mm outer dia Pipe 1.00 m 704.05 One Running 704.00

Metre
18.85A.2 22 mm outer dia Pipe 1.00 m 1025.25 One Running 1025.00
Metre
18.85A.3 28 mm outer dia Pipe 1.00 m 1272.15 One Running 1272.00
Metre

DSR - 2023 IN MS EXCEL Page 184 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.85A.4 35 mm outer dia Pipe 1.00 m 1765.10 One Running 1765.00
Metre
18.85A.5 42 mm outer dia Pipe 1.00 m 2124.00 One Running 2124.00
Metre
18.85A.6 54 mm outer dia Pipe 1.00 m 2699.10 One Running 2699.00
Metre
18.86 Providing and fixing Stainless Steel pipe and fitting of
grade AISI 304 as per JIS standard 3448 complete with
press type fitting (fitting shall be paid for separately) i/c
fixing of the pipe with clamps at 1.00 m spacing and
also including cutting of chases and making good the
walls including testing of joints complete as per
direction of Engineer-in-charge. (The pipe length
inserted in the fitting shall not be measured for
payment) Internal work- Concealed pipe

18.86.1 15.88 mm outer dia Pipes. 1.00 m 622.25 One Running 622.00
Metre
18.86.2 22.22 mm outer dia Pipes. 1.00 m 801.50 One Running 802.00
Metre
18.86A Providing and fixing stainless Steel pipe and fitting of
grade 316L as per IS 6911:2017 and conforming to EN-
10312 standards complete with press type fitting
( fitting shall be paid for separately) i/c fixing of the pipe
with clamps at 1.00 m spacing and also including cutting
of chases and making good the walls including testing of
joints complete as per the direction of Engineer- in-
charge. ( The pipe length inserted in the fitting shall not
be measure for payment). Internal work - Concealed
Pipe

18.86A.1 15 mm outer dia. Pipes 1.00 m 906.10 One Running 906.00

Metre
18.86A.2 22 mm outer dia Pipes 1.00 m 1227.25 One Running 1227.00
Metre
18.87 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge - Coupling/Socket.

18.87.1 For 15.88 mm outer dia pipe 1.00 No. 93.90 Each 94.00
18.87.2 For 22.22 mm outer dia pipe 1.00 No. 113.80 Each 114.00
18.87.3 For 28.58 mm outer dia pipe 1.00 No. 156.50 Each 157.00
18.87.4 For 34.00 mm outer dia pipe 1.00 No. 213.40 Each 213.00
18.87.5 For 42.70 mm outer dia pipe 1.00 No. 256.10 Each 256.00
18.87.6 For 48.60 mm outer dia pipe 1.00 No. 291.65 Each 292.00
18.87A Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge - Coupling/Socket.

18.87A.1 For 15 mm outer dia pipe 1.00 No. 341.45 Each 341.00
18.87A.2 For 22 mm outer dia pipe 1.00 No. 426.80 Each 427.00
18.87A.3 For 28 mm outer dia pipe 1.00 No. 497.90 Each 498.00
18.87A.4 For 35 mm outer dia pipe 1.00 No. 625.95 Each 626.00
18.87A.5 For 42 mm outer dia pipe 1.00 No. 846.45 Each 846.00
18.87A.6 For 54 mm outer dia pipe 1.00 No. 1017.20 Each 1017.00

DSR - 2023 IN MS EXCEL Page 185 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.88 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of providing and
fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard
with V-profile or M-profile and with O-ring sealing
gasket of EPDM material of required dia as per dirction
of Engineer-in-charge

Reducer
18.88.1 For 22.22 mm x 15.88 mm outer dia pipe 1.00 No. 139.40 Each 139.00
18.88.2 For 28.58 mm x 15.88 mm outer dia pipe 1.00 No. 186.35 Each 186.00
18.88.3 For 28.58 mm x 22.22 mm outer dia pipe 1.00 No. 189.20 Each 189.00
18.88.4 For 34.00 mm x 15.88 mm outer dia pipe 1.00 No. 313.00 Each 313.00
18.88.5 For 34.00 mm x 22.22 mm outer dia pipe 1.00 No. 327.20 Each 327.00
18.88.6 For 34.00 mm x 28.58 mm outer dia pipe 1.00 No. 327.20 Each 327.00
18.88.7 For 42.70 mm x 15.88 mm outer dia pipe 1.00 No. 517.85 Each 518.00
18.88.8 For 42.70 mm x 22.22 mm outer dia pipe 1.00 No. 529.25 Each 529.00
18.88.9 For 42.70 mm x 28.58 mm outer dia pipe 1.00 No. 606.05 Each 606.00
18.88.10 For 42.70 mm x 34.00 mm outer dia pipe 1.00 No. 643.05 Each 643.00
18.88.11 For 48.60 mm x 15.88 mm outer dia pipe 1.00 No. 643.05 Each 643.00
18.88.12 For 48.60 mm x 22.22 mm outer dia pipe 1.00 No. 643.05 Each 643.00
18.88.13 For 48.60 mm x 28.58 mm outer dia pipe 1.00 No. 643.05 Each 643.00
18.88.14 For 48.60 mm x 34.00 mm outer dia pipe 1.00 No. 664.35 Each 664.00
18.88.15 For 48.60 mm x 42.70 mm outer dia pipe 1.00 No. 667.20 Each 667.00
18.88A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS : 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of
requireddia as per dirction of Engineer-in-charge.

Reducer
18.88A.1 For 22 mm x 15 mm outer dia pipe 1.00 No. 405.45 Each 405.00
18.88A.2 For 28 mm x 15 mm outer dia pipe 1.00 No. 490.80 Each 491.00
18.88A.3 For 28 mm x 22 mm outer dia pipe 1.00 No. 597.50 Each 598.00
18.88A.4 For 35 mm x 22 mm outer dia pipe 1.00 No. 604.60 Each 605.00
18.88A.5 For 35 mm x 28 mm outer dia pipe 1.00 No. 746.85 Each 747.00
18.88A.6 For 42 mm x 22 mm outer dia pipe 1.00 No. 960.30 Each 960.00
18.88A.7 For 42 mm x 28 mm outer dia pipe 1.00 No. 1095.45 Each 1095.00
18.88A.8 For 42 mm x 35 mm outer dia pipe 1.00 No. 1145.25 Each 1145.00
18.88A.9 For 54 mm x 28 mm outer dia pipe 1.00 No. 1330.15 Each 1330.00
18.88A.10 For 54 mm x 35 mm outer dia pipe 1.00 No. 1572.00 Each 1572.00
18.88A.11 For 54 mm x 42 mm outer dia pipe 1.00 No. 1636.05 Each 1636.00
18.89 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge - Slip
Coupling/Socket

18.89.1 For 15.88 mm outer dia pipe 1.00 No. 92.45 Each 92.00
18.89.2 For 22.22 mm outer dia pipe 1.00 No. 113.80 Each 114.00
18.89.3 For 28.58 mm outer dia pipe 1.00 No. 156.50 Each 157.00
18.89.4 For 34.00 mm outer dia pipe 1.00 No. 220.50 Each 221.00
18.89.5 For 42.70 mm outer dia pipe 1.00 No. 256.10 Each 256.00
18.89.6 For 48.60 mm outer dia pipe 1.00 No. 277.40 Each 277.00

DSR - 2023 IN MS EXCEL Page 186 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.89A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Sleeve/Slip
Coupling/Socket

18.89A.1 For 15 mm outer dia pipe 1.00 No. 597.50 Each 598.00
18.89A.2 For 22 mm outer dia pipe 1.00 No. 711.30 Each 711.00
18.89A.3 For 28 mm outer dia pipe 1.00 No. 825.15 Each 825.00
18.89A.4 For 35 mm outer dia pipe 1.00 No. 917.60 Each 918.00
18.89A.5 For 42 mm outer dia pipe 1.00 No. 1066.95 Each 1067.00
18.89A.6 For 54 mm outer dia pipe 1.00 No. 1515.10 Each 1515.00
18.90 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Elbow 90 degrees

18.90.1 For 15.88 mm outer dia pipe 1.00 No. 99.60 Each 100.00
18.90.2 For 22.22 mm outer dia pipe 1.00 No. 113.80 Each 114.00
18.90.3 For 28.58 mm outer dia pipe 1.00 No. 163.60 Each 164.00
18.90.4 For 34.00 mm outer dia pipe 1.00 No. 204.85 Each 205.00
18.90.5 For 42.70 mm outer dia pipe 1.00 No. 221.95 Each 222.00
18.90.6 For 48.60 mm outer dia pipe 1.00 No. 273.15 Each 273.00
18.90A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Elbow 90
degrees

18.90A.1 For 15 mm outer dia pipe 1.00 No. 483.70 Each 484.00
18.90A.2 For 22 mm outer dia pipe 1.00 No. 682.85 Each 683.00
18.90A.3 For 28 mm outer dia pipe 1.00 No. 910.50 Each 911.00
18.90A.4 For 35 mm outer dia pipe 1.00 No. 1493.75 Each 1494.00
18.90A.5 For 42 mm outer dia pipe 1.00 No. 2418.50 Each 2419.00
18.90A.6 For 54 mm outer dia pipe 1.00 No. 3200.95 Each 3201.00
18.91 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge. : Reducing Elbow
90 degrees

18.91.1 For 22.22 mm x 15.88 mm outer dia pipe 1.00 No. 223.35 Each 223.00
18.91.2 For 28.58 mm x 15.88 mm outer dia pipe 1.00 No. 304.45 Each 304.00
18.91.3 For 28.58 mm x 22.22 mm outer dia pipe 1.00 No. 318.65 Each 319.00
18.91.4 For 34.00 mm x 22.22 mm outer dia pipe 1.00 No. 426.80 Each 427.00
18.91.5 For 34.00 mm x 28.58 mm outer dia pipe 1.00 No. 512.15 Each 512.00
18.91.6 For 42.70 mm x 34.00 mm outer dia pipe 1.00 No. 554.80 Each 555.00
18.92 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge. : Equal Tee

18.92.1 For 15.88 mm outer dia pipe 1.00 No. 197.75 Each 198.00
18.92.2 For 22.22 mm outer dia pipe 1.00 No. 300.20 Each 300.00
18.92.3 For 28.58 mm outer dia pipe 1.00 No. 466.60 Each 467.00
18.92.4 For 34.00 mm outer dia pipe. 1.00 No. 688.55 Each 689.00
18.92.5 For 42.70 mm outer dia pipe 1.00 No. 1088.30 Each 1088.00

DSR - 2023 IN MS EXCEL Page 187 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.92.6 For 48.60 mm outer dia pipe 1.00 No. 1429.75 Each 1430.00
18.92A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Equal Tee

18.92A.1 For 15 mm outer dia pipe 1.00 No. 796.70 Each 797.00
18.92A.2 For 22 mm outer dia pipe 1.00 No. 931.85 Each 932.00
18.92A.3 For 28 mm outer dia pipe 1.00 No. 1145.25 Each 1145.00
18.92A.4 For 35 mm outer dia pipe 1.00 No. 1422.65 Each 1423.00
18.92A.5 For 42 mm outer dia pipe 1.00 No. 1991.70 Each 1992.00
18.92A.6 For 54 mm outer dia pipe 1.00 No. 2390.05 Each 2390.00
18.93 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Reducing Tee

18.93.1 For 22.22 mm x 15.88 mm outer dia pipe 1.00 No. 268.85 Each 269.00
18.93.2 For 28.58 mm x 15.88 mm outer dia pipe 1.00 No. 357.10 Each 357.00
18.93.3 For 28.58 mm x 22.22 mm outer dia pipe 1.00 No. 362.75 Each 363.00
18.93.4 For 34.00 mm x 15.88 mm outer dia pipe 1.00 No. 633.10 Each 633.00
18.93.5 For 34.00 mm x 22.22 mm outer dia pipe 1.00 No. 654.40 Each 654.00
18.93.6 For 34.00 mm x 28.58 mm outer dia pipe 1.00 No. 675.75 Each 676.00
18.93.7 For 42.70 mm x 15.88 mm outer dia pipe 1.00 No. 1045.65 Each 1046.00
18.93.8 For 42.70 mm x 22.22 mm outer dia pipe 1.00 No. 1066.95 Each 1067.00
18.93.9 For 42.70 mm x 28.58 mm outer dia pipe 1.00 No. 1095.45 Each 1095.00
18.93.10 For 42.70 mm x 34.00 mm outer dia pipe 1.00 No. 1123.90 Each 1124.00
18.93.11 For 48.60 mm x 15.88 mm outer dia pipe 1.00 No. 1280.35 Each 1280.00
18.93.12 For 48.60 mm x 22.22 mm outer dia pipe 1.00 No. 1296.00 Each 1296.00
18.93.13 For 48.60 mm x 28.58 mm outer dia pipe 1.00 No. 1320.20 Each 1320.00
18.93.14 For 48.60 mm x 34.00 mm outer dia pipe 1.00 No. 1372.85 Each 1373.00
18.93.15 For 48.60 mm x 42.70 mm outer dia pipe 1.00 No. 1401.30 Each 1401.00
18.93A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Reducing
Tee

18.93A.1 For 22 mm x 15 mm outer dia pipe 1.00 No. 910.50 Each 911.00
18.93A.2 For 28 mm x 15 mm outer dia pipe 1.00 No. 1131.00 Each 1131.00
18.93A.3 For 28 mm x 22 mm outer dia pipe 1.00 No. 1138.10 Each 1138.00
18.93A.4 For 35 mm x 15 mm outer dia pipe 1.00 No. 1429.75 Each 1430.00
18.93A.5 For 35 mm x 22 mm outer dia pipe 1.00 No. 1436.85 Each 1437.00
18.93A.6 For 35 mm x 28 mm outer dia pipe 1.00 No. 1451.10 Each 1451.00
18.93A.7 For 42 mm x 22 mm outer dia pipe 1.00 No. 2013.05 Each 2013.00
18.93A.8 For 42 mm x 28 mm outer dia pipe 1.00 No. 2034.35 Each 2034.00
18.93A.9 For 42 mm x 35 mm outer dia pipe 1.00 No. 2048.60 Each 2049.00
18.93A.10 For 54 mm x 22 mm outer dia pipe 1.00 No. 2390.05 Each 2390.00
18.93A.11 For 54 mm x 28 mm outer dia pipe 1.00 No. 2446.95 Each 2447.00
18.93A.12 For 54 mm x 35 mm outer dia pipe 1.00 No. 2468.25 Each 2468.00
18.93A.13 For 54 mm x 42 mm outer dia pipe 1.00 No. 2496.75 Each 2497.00
18.94 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Male Thread Tee

DSR - 2023 IN MS EXCEL Page 188 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.94.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 291.65 Each 292.00

18.94.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 334.30 Each 334.00

18.94.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 355.65 Each 356.00

18.94.4 For 28.58 mm outer dia x 15 mm nominal dia threaded 1.00 No. 448.15 Each 448.00

18.94.5 For 28.58 mm outer dia x 20 mm nominal dia threaded 1.00 No. 462.35 Each 462.00

18.94.6 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 476.60 Each 477.00

18.94.7 For 34.00 mm outer dia x 15 mm nominal dia threaded 1.00 No. 661.50 Each 662.00

18.94.8 For 34.00 mm outer dia x 20 mm nominal dia threaded 1.00 No. 675.75 Each 676.00

18.94.9 For 34.00 mm outer dia x 25 mm nominal dia threaded 1.00 No. 704.20 Each 704.00

18.94.10 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 732.65 Each 733.00

18.94.11 For 42.70 mm outer dia x 15 mm nominal dia threaded 1.00 No. 1010.05 Each 1010.00

18.94.12 For 42.70 mm outer dia x 20 mm nominal dia threaded 1.00 No. 1031.40 Each 1031.00

18.94.13 For 42.70 mm outer dia x 25 mm nominal dia threaded 1.00 No. 1088.30 Each 1088.00

18.94.14 For 42.70 mm outer dia x 32 mm nominal dia threaded 1.00 No. 1131.00 Each 1131.00

18.94.15 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1173.65 Each 1174.00

18.94.16 For 48.60 mm outer dia x 15 mm nominal dia threaded 1.00 No. 1415.55 Each 1416.00

18.94.17 For 48.60 mm outer dia x 20 mm nominal dia threaded 1.00 No. 1442.55 Each 1443.00

18.94.18 For 48.60 mm outer dia x 25 mm nominal dia threaded 1.00 No. 1458.20 Each 1458.00

18.94.19 For 48.60 mm outer dia x 32 mm nominal dia threaded 1.00 No. 1493.75 Each 1494.00

18.94.20 For 48.60 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1536.45 Each 1536.00

18.94.21 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1586.25 Each 1586.00

18.95 Providing and fixing required Stainless Steel Fitting of

press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Female Thread Tee

18.95.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 277.40 Each 277.00

18.95.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 305.85 Each 306.00

18.95.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 320.10 Each 320.00

18.95.4 For 28.58 mm outer dia x 15 mm nominal dia threaded 1.00 No. 405.45 Each 405.00

18.95.5 For 28.58 mm outer dia x 20 mm nominal dia threaded 1.00 No. 419.70 Each 420.00

DSR - 2023 IN MS EXCEL Page 189 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.95.6 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 433.90 Each 434.00

18.95.7 For 34.00 mm outer dia x 15 mm nominal dia threaded 1.00 No. 647.30 Each 647.00

18.95.8 For 34.00 mm outer dia x 20 mm nominal dia threaded 1.00 No. 690.00 Each 690.00

18.95.9 For 34.00 mm outer dia x 25 mm nominal dia threaded 1.00 No. 732.65 Each 733.00

18.95.10 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 775.35 Each 775.00

18.95.11 For 42.70 mm outer dia x 15 mm nominal dia threaded 1.00 No. 995.85 Each 996.00

18.95.12 For 42.70 mm outer dia x 20 mm nominal dia threaded 1.00 No. 1010.05 Each 1010.00

18.95.13 For 42.70 mm outer dia x 25 mm nominal dia threaded 1.00 No. 1038.50 Each 1039.00

18.95.14 For 42.70 mm outer dia x 32 mm nominal dia threaded 1.00 No. 1066.95 Each 1067.00

18.95.15 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1145.25 Each 1145.00

18.95.16 For 48.60 mm outer dia x 15 mm nominal dia threaded 1.00 No. 1287.50 Each 1288.00

18.95.17 For 48.60 mm outer dia x 20 mm nominal dia threaded 1.00 No. 1301.70 Each 1302.00

18.95.18 For 48.60 mm outer dia x 25 mm nominal dia threaded 1.00 No. 1323.05 Each 1323.00

18.95.19 For 48.60 mm outer dia x 32 mm nominal dia threaded 1.00 No. 1394.20 Each 1394.00

18.95.20 For 48.60 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1429.75 Each 1430.00

18.95.21 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1543.55 Each 1544.00

18.95A Providing and fixing required Stainless Steel Fitting of

press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Female
Thread Tee

18.95A.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 889.15 each 889.00
18.95A.2 For 22 mm outer dia x 1/2" nominal dia threaded 1.00 No. 967.40 each 967.00
18.95A.3 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1095.45 each 1095.00
18.95A.4 For 28 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1159.45 each 1159.00
18.95A.5 For 28 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1202.15 each 1202.00
18.95A.6 For 28 mm outer dia x 1" nominal dia threaded 1.00 No. 1330.15 each 1330.00
18.95A.7 For 35 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1337.30 each 1337.00
18.95A.8 For 35 mm outer dia x 1-1/4" nominal dia threaded 1.00 No. 1842.30 each 1842.00
18.95A.9 For 42 mm outer dia x 1-1/4" nominal dia threaded 1.00 No. 2141.05 each 2141.00
18.95A.10 For 54 mm outer dia x 1-1/2" nominal dia threaded 1.00 No. 3058.65 each 3059.00
18.95A.11 For 54 mm outer dia x 2" nominal dia threaded 1.00 No. 3670.40 each 3670.00
18.96 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Female Thread
Connector/Adapter.

18.96.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 264.60 Each 265.00

18.96.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 291.65 Each 292.00

DSR - 2023 IN MS EXCEL Page 190 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.96.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 337.15 Each 337.00

18.96.4 For 28.58 mm outer dia x 15 mm nominal dia threaded 1.00 No. 394.05 Each 394.00

18.96.5 For 28.58 mm outer dia x 20 mm nominal dia threaded 1.00 No. 412.55 Each 413.00

18.96.6 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 505.05 Each 505.00

18.96.7 For 34.00 mm outer dia x 25 mm nominal dia threaded 1.00 No. 640.20 Each 640.00

18.96.8 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 768.25 Each 768.00

18.96.9 For 42.70 mm outer dia x 32 mm nominal dia threaded 1.00 No. 953.15 Each 953.00

18.96.10 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1002.95 Each 1003.00

18.96.11 For 48.60 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1287.50 Each 1288.00

18.96.12 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1387.05 Each 1387.00

18.96A Providing and fixing required Stainless Steel Fitting of

press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Female
Thread Connector/Adapter

18.96A.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 697.10 each 697.00
18.96A.2 For 22 mm outer dia x 1/2" nominal dia threaded 1.00 No. 782.45 each 782.00
18.96A.3 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 917.60 each 918.00
18.96A.4 For 28 mm outer dia x1" nominal dia threaded 1.00 No. 1515.10 each 1515.00
18.96A.5 For 35 mm outer dia x 1-1/4" nominal dia threaded 1.00 No. 1621.80 each 1622.00
18.96A.6 For 42 mm outer dia x1-1/2" nominal dia threaded 1.00 No. 2489.60 each 2490.00
18.96A.7 For 54 mm outer dia x 2" nominal dia threaded 1.00 No. 3819.80 each 3820.00
18.97 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Male Thread
Connector/Adapter

18.97.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 250.40 Each 250.00

18.97.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 268.85 Each 269.00

18.97.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 300.20 Each 300.00

18.97.4 For 28.58 mm outer dia x 20 mm nominal dia threaded 1.00 No. 458.10 Each 458.00

18.97.5 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 460.95 Each 461.00

18.97.6 For 34.00 mm outer dia x 25 mm nominal dia threaded 1.00 No. 675.75 Each 676.00

18.97.7 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 803.80 Each 804.00

18.97.8 For 42.70 mm outer dia x 32 mm nominal dia threaded 1.00 No. 1017.20 Each 1017.00

18.97.9 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1038.50 Each 1039.00

18.97.10 For 48.60 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1330.15 Each 1330.00

DSR - 2023 IN MS EXCEL Page 191 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.97.11 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1621.80 Each 1622.00

18.97A Providing and fixing required Stainless Steel Fitting of

press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Male Thread
Connector/Adapter

18.97A.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 640.20 each 640.00
18.97A.2 For 22 mm outer dia x 1/2" nominal dia threaded 1.00 No. 761.10 each 761.00
18.97A.3 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 803.80 each 804.00
18.97A.4 For 28 mm outer dia x1" nominal dia threaded 1.00 No. 1052.75 each 1053.00
18.97A.5 For 35 mm outer dia x 1-1/4" nominal dia threaded 1.00 No. 1543.55 each 1544.00
18.97A.6 For 42 mm outer dia x1-1/2" nominal dia threaded 1.00 No. 2247.75 each 2248.00
18.97A.7 For 54 mm outer dia x 2" nominal dia threaded 1.00 No. 3016.00 each 3016.00
18.98 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Valve Connector

18.98.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 317.25 Each 317.00

18.98.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 364.20 Each 364.00

18.98.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 395.50 Each 396.00

18.98.4 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 604.60 Each 605.00

18.98.5 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 917.60 Each 918.00

18.98.6 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1298.85 Each 1299.00

18.98.7 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1756.95 Each 1757.00

18.99 Providing and fixing required Stainless Steel Fitting of

press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Female Threaded
Elbow 90 degrees.

18.99.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 270.30 Each 270.00

18.99.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 305.85 Each 306.00

18.99.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 341.45 Each 341.00

18.99.4 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 369.90 Each 370.00

18.99.5 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 476.60 Each 477.00

18.99.6 For 42.70 mm outer dia x 32 mm nominal dia threaded 1.00 No. 754.00 Each 754.00

18.99.7 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 754.00 Each 754.00

18.99.8 For 48.60 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1123.90 Each 1124.00

18.99.9 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1123.90 Each 1124.00

DSR - 2023 IN MS EXCEL Page 192 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.99A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Female
Threaded Elbow 90 degrees

18.99A.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1017.20 each 1017.00
18.99A.2 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1365.70 each 1366.00
18.99A.3 For 28 mm outer dia x 1" nominal dia threaded 1.00 No. 1877.90 each 1878.00
18.99A.4 For 35 mm outer dia x1-1/4" nominal dia threaded 1.00 No. 3051.55 each 3052.00
18.99A.5 For 42 mm outer dia x 1-1/2" nominal dia threaded 1.00 No. 3321.85 each 3322.00
18.99A.6 For 54 mm outer dia x 2" nominal dia threaded 1.00 No. 5135.70 each 5136.00
18.100 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge : Male Threaded
Elbow 90 degrees

18.100.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 1.00 No. 325.80 Each 326.00

18.100.2 For 22.22 mm outer dia x 15 mm nominal dia threaded 1.00 No. 355.65 Each 356.00

18.100.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 1.00 No. 377.00 Each 377.00

18.100.4 For 28.58 mm outer dia x 25 mm nominal dia threaded 1.00 No. 405.45 Each 405.00

18.100.5 For 34.00 mm outer dia x 25 mm nominal dia threaded 1.00 No. 448.15 Each 448.00

18.100.6 For 34.00 mm outer dia x 32 mm nominal dia threaded 1.00 No. 448.15 Each 448.00

18.100.7 For 42.70 mm outer dia x 32 mm nominal dia threaded 1.00 No. 682.85 Each 683.00

18.100.8 For 42.70 mm outer dia x 40 mm nominal dia threaded 1.00 No. 754.00 Each 754.00

18.100.9 For 48.60 mm outer dia x 40 mm nominal dia threaded 1.00 No. 1088.30 Each 1088.00

18.100.10 For 48.60 mm outer dia x 50 mm nominal dia threaded 1.00 No. 1187.90 Each 1188.00

18.100A Providing and fixing required Stainless Steel Fitting of

press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Male
Threaded Elbow 90 degrees

18.100A.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 832.25 each 832.00
18.100A.2 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1251.95 each 1252.00
18.100A.3 For 28 mm outer dia x 1" nominal dia threaded 1.00 No. 1664.50 each 1665.00
18.100A.4 For 35 mm outer dia x1-1/4" nominal dia threaded 1.00 No. 2290.45 each 2290.00
18.100A.5 For 42 mm outer dia x 1-1/2" nominal dia threaded 1.00 No. 4196.80 each 4197.00
18.100A.6 For 54 mm outer dia x 2" nominal dia threaded 1.00 No. 4772.95 each 4773.00
18.101 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge. : Cap

18.101.1 For 15.88 mm outer dia pipe 1.00 No. 58.35 Each 58.00
18.101.2 For 22.22 mm outer dia pipe 1.00 No. 85.35 Each 85.00
18.101.3 For 28.58 mm outer dia pipe 1.00 No. 122.35 Each 122.00

DSR - 2023 IN MS EXCEL Page 193 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.101.4 For 34.00 mm outer dia pipe 1.00 No. 234.75 Each 235.00
18.101.5 For 42.70 mm outer dia pipe 1.00 No. 342.85 Each 343.00
18.101.6 For 48.60 mm outer dia pipe 1.00 No. 426.80 Each 427.00
18.101A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Cap

18.101A.1 For 15 mm outer dia pipe 1.00 No. 505.05 each 505.00
18.101A.2 For 22 mm outer dia pipe 1.00 No. 654.40 each 654.00
18.101A.3 For 28 mm outer dia pipe 1.00 No. 818.00 each 818.00
18.101A.4 For 35 mm outer dia pipe 1.00 No. 1145.25 each 1145.00
18.101A.5 For 42 mm outer dia pipe 1.00 No. 2489.60 each 2490.00
18.101A.6 For 54 mm outer dia pipe 1.00 No. 2738.55 each 2739.00
18.102 Providing and fixing required Stainless Steel Fitting of
press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as
per direction of Engineer-in-charge. : Pipe Bridge

18.102.1 For 15.88 mm outer dia pipe 1.00 No. 136.55 Each 137.00
18.102.2 For 22.22 mm outer dia pipe 1.00 No. 240.45 Each 240.00
18.102.3 For 28.58 mm outer dia pipe 1.00 No. 386.95 Each 387.00
18.102A Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Pipe Bridge

18.102A.1 For 15 mm outer dia pipe 1.00 No. 654.40 each 654.00
18.102A.2 For 22 mm outer dia pipe 1.00 No. 1764.10 each 1764.00
18.102A.3 For 28 mm outer dia pipe 1.00 No. 2425.60 each 2426.00
18.103 Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Male Union

18.103.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1408.40 each 1408.00
18.103.2 For 22 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1422.65 each 1423.00
18.103.3 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1628.90 each 1629.00
18.103.4 For 28 mm outer dia x1" nominal dia threaded 1.00 No. 2873.70 each 2874.00
18.103.5 For 35 mm outer dia x 1-1/4" nominal dia threaded 1.00 No. 3001.75 each 3002.00
18.103.6 For 42 mm outer dia x1-1/2" nominal dia threaded 1.00 No. 3385.85 each 3386.00
18.103.7 For 54 mm outer dia x 2" nominal dia threaded 1.00 No. 5861.25 each 5861.00
18.104 Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Female
Union

18.104.1 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1508.00 each 1508.00
18.104.2 For 28 mm outer dia x 1" nominal dia threaded 1.00 No. 2034.35 each 2034.00

DSR - 2023 IN MS EXCEL Page 194 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
18.105 Providing and fixing required Stainless Steel Fitting of
press fit design of grade 316L as per IS 6911:2017 and
conforming to EN-10312 standard with V-profile and
with O-ring sealing gasket of EPDM material of required
dia as per direction of Engineer-in-charge - Female
Transition Elbow / FTE

18.105.1 For 15 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1031.40 each 1031.00
18.105.2 For 22 mm outer dia x 1/2" nominal dia threaded 1.00 No. 1379.95 each 1380.00
18.105.3 For 22 mm outer dia x 3/4" nominal dia threaded 1.00 No. 1429.75 each 1430.00
Total of the Sub-Head - Water Supply : 1952347.00
Sub-Head : Drainage
19.1 Providing, laying and jointing glazed stoneware pipes
class SP-1 with stiff mixture of cement mortar in the
proportion of 1:1 (1 cement : 1 fine sand) including
testing of joints etc. complete :

19.1.1 100 mm diameter 1.00 m 443.60 One Running 444.00

Metre
19.1.2 150 mm diameter 1.00 m 695.80 One Running 696.00
Metre
19.1.3 200 mm diameter 1.00 m 970.35 One Running 970.00
Metre
19.1.4 250 mm diameter 1.00 m 1505.60 One Running 1506.00
Metre
19.1.5 300 mm diameter 1.00 m 2064.15 One Running 2064.00
Metre
19.2 Providing and laying cement concrete 1:5:10 (1
cement : 5 coarse sand : 10 graded stone aggregate 40
mm nominal size) all-round S.W. pipes including bed
concrete as per standard design :

19.2.1 100 mm diameter S.W. pipe 1.00 m 964.75 One Running 965.00
Metre
19.2.2 150 mm diameter S.W. pipe 1.00 m 1179.85 One Running 1180.00
Metre
19.2.3 200 mm diameter S.W. pipe 1.00 m 1375.45 One Running 1375.00
Metre
19.2.4 250 mm diameter S.W. pipe 1.00 m 1590.55 One Running 1591.00
Metre
19.3 Providing and laying cement concrete 1:5:10 (1
cement : 5 coarse sand : 10 graded stone aggregate 40
mm nominal size) up to haunches of S.W. pipes
including bed concrete as per standard design :

19.3.1 100 mm diameter S.W. pipe 1.00 m 458.50 One Running 459.00
Metre
19.3.2 150 mm diameter S.W. pipe 1.00 m 743.10 One Running 743.00
Metre
19.3.3 200 mm diameter S.W. pipe 1.00 m 873.50 One Running 874.00
Metre
19.3.4 250 mm diameter S.W. pipe 1.00 m 1016.90 One Running 1017.00
Metre
19.3.5 300 mm diameter S.W. pipe 1.00 m 1173.35 One Running 1173.00
Metre
19.4 Providing and fixing square-mouth S.W. gully trap class
SP-1 complete with C.I. grating brick masonry chamber
with water tight C.I. cover with frame of 300 x300 mm
size (inside) the weight of cover to be not less than 4.50
kg and frame to be not less than 2.70 kg as per standard
design:

19.4.1 100x100 mm size P type

DSR - 2023 IN MS EXCEL Page 195 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 2707.65 Each 2708.00
class designation 7.5
19.4.1.2 With Sewer bricks conforming to IS : 4885 1.00 No. 2685.20 Each 2685.00
19.4.2 150 x 100 mm size P type.
19.4.2.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 2734.20 Each 2734.00
class designation 7.5
19.4.2.2 With sewer bricks conforming to IS : 4885 1.00 No. 2711.70 Each 2712.00
19.4.3 180x150 mm size P type
19.4.3.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 2802.15 Each 2802.00
class designation 7.5
19.4.3.2 With Sewer bricks conforming to IS : 4885 1.00 No. 2779.65 Each 2780.00
19.5 Dismantling of old S.W. pipes including breaking of
joints and bed concrete stacking of useful materials
near the site within 50 m lead and disposal of
unserviceable materials into municipal dumps :

19.5.1 100 mm diameter 1.00 m 89.00 One Running 89.00

Metre
19.5.2 150 mm diameter 1.00 m 98.45 One Running 98.00
Metre
19.5.3 200 mm diameter 1.00 m 104.70 One Running 105.00
Metre
19.5.4 250 mm diameter 1.00 m 111.00 One Running 111.00
Metre
19.5.5 300 mm diameter 1.00 m 117.25 One Running 117.00
Metre
19.5.6 350 mm diameter 1.00 m 135.05 One Running 135.00
Metre
19.5.7 400 mm diameter 1.00 m 147.65 One Running 148.00
Metre
19.5.8 450 mm diameter 1.00 m 153.90 One Running 154.00
Metre
19.6 Providing and laying non-pressure NP2 class (light duty)
R.C.C. pipes with collars jointed with stiff mixture of
cement mortar in the proportion of 1:2 (1 cement : 2
fine sand) including testing of joints etc. complete :

19.6.1 100 mm dia. R.C.C. pipe 1.00 m 507.05 One Running 507.00
Metre
19.6.2 150 mm dia. R.C.C. pipe 1.00 m 556.45 One Running 556.00
Metre
19.6.3 250 mm dia. R.C.C. pipe 1.00 m 899.80 One Running 900.00
Metre
19.6.4 300 mm dia. R.C.C. pipe 1.00 m 994.30 One Running 994.00
Metre
19.6.5 450 mm dia. R.C.C. pipe 1.00 m 1620.95 One Running 1621.00
Metre
19.6.6 500 mm dia. R.C.C. pipe 1.00 m 1918.90 One Running 1919.00
Metre
19.6.7 600 mm dia. R.C.C. pipe 1.00 m 2243.40 One Running 2243.00
Metre
19.6.8 700 mm dia. R.C.C. pipe 1.00 m 2932.50 One Running 2933.00
Metre
19.6.9 800 mm dia. R.C.C. pipe 1.00 m 3511.95 One Running 3512.00
Metre
19.6.10 900 mm dia. R.C.C. pipe 1.00 m 4750.85 One Running 4751.00
Metre
19.6.11 1000 mm dia. R.C.C. pipe 1.00 m 5562.60 One Running 5563.00
Metre

DSR - 2023 IN MS EXCEL Page 196 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.6.12 1100 mm dia. R.C.C. pipe 1.00 m 6276.60 One Running 6277.00
Metre
19.6.13 1200 mm dia. R.C.C. pipe 1.00 m 7102.15 One Running 7102.00
Metre
19.7 Constructing brick masonry manhole in cement mortar
1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with
1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3
graded stone aggregate 20 mm nominal size),
foundation concrete 1:4:8 mix (1 cement : 4 coarse
sand (zone-III) : 8 graded stone aggregate 40 mm
nominal size), inside plastering 12 mm thick with
cement mortar 1:3 (1 cement : 3 coarse sand) finished
with floating coat of neat cement and making channels
in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) finished
with a floating coat of neat cement complete as per
standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I.

cover with frame (light duty) 455x610 mm internal
dimensions, total weight of cover and frame to be not
less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg) :

19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 12770.55 Each 12771.00
class designation 7.5
19.7.1.2 With Sewer bricks conforming to IS : 4885 1.00 No. 12711.80 Each 12712.00
19.7.2 Inside size 120x90 cm and 90 cm deep including C.I.
cover with frame (medium duty) 500 mm internal
diameter, total weight of cover and frame to be not less
than 1 16 kg (weight of cover 58 kg and weight of frame
58 kg) :

19.7.2.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 26405.50 Each 26406.00
class designation 7.5
19.7.2.2 With Sewer bricks conforming to IS : 4885 1.00 No. 26244.70 Each 26245.00
19.7.3 Inside size 120x90 cm and 90 cm deep including C.I.
cover with frame (heavy duty) 560 mm internal
diameter, total weight of cover and frame to be not less
than 208 kg (weight of cover 108 kg and weight of
frame 100 kg) :

19.7.3.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 32857.85 Each 32858.00
class designation 7.5
19.7.3.2 With Sewer bricks conforming to IS : 4885 1.00 No. 32719.50 Each 32720.00
19.8 Extra for depth for manholes
19.8.1 Size 90x80 cm
19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 8825.40 One Running 8825.00
class designation 7.5 Metre
19.8.1.2 With Sewer bricks conforming to IS : 4885 1.00 m 8654.25 One Running 8654.00
Metre
19.8.2 Size 120x90 cm
19.8.2.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 10585.50 One Running 10586.00
class designation 7.5 Metre
19.8.2.2 With Sewer bricks conforming to IS : 4885 1.00 m 10381.45 One Running 10381.00
Metre

DSR - 2023 IN MS EXCEL Page 197 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.9 Constructing brick masonry circular type manhole 0.91
m internal dia at bottom and 0.56m dia at top in
cement mortar 1:4 (1 cement : 4 coarse sand), inside
cement plaster 12 mm thick with cement mortar 1:3 (1
cement : 3 coarse sand) finished with a floating coat of
neat cement, foundation concrete 1:3:6 mix (1 cement :
3 coarse sand : 6 graded stone aggregate 40 mm
nominal size), and making necessary channel in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) finished with a
floating coat of neat cement, all complete as per
standard design :

19.9.1 0.91 m deep with S.F .R.C. cover and frame (heavy
duty , HD-20 grade designation) 560 mm internal
diameter conforming to I.S. 12592, total weight of
cover and frame to be not less than 182 kg., fixed in
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) including
centering, shuttering all complete. (Excavation, foot
rests and 12mm thick cement plaster at the external
surface shall be paid for separately) :

19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 12725.00 Each 12725.00
class designation 7.5
19.9.1.2 With Sewer bricks conforming to IS : 4885 1.00 No. 12600.40 Each 12600.00
19.10 Extra depth for circular type manhole 0.91 m internal
dia (at bottom) beyond 0.91 m to 1.67 m
19.10.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 7591.80 One Running 7592.00
class designation 7.5 Metre
19.10.2 With Sewer bricks conforming IS : 4885 1.00 m 7448.45 One Running 7448.00
Metre
19.11 Constructing brick masonry circular manhole 1.22 m
internal dia at bottom and 0.56 m dia at top in cement
mortar 1:4 (1 cement :4 coarse sand) inside cement
plaster 12 mm thick with cement mortar 1:3 (1 cement :
3 coarse sand) finished with a floating coat of neat
cement foundation concrete 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 40 mm nominal size)
and making necessary channel in cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) finished with a floating coat of neat
cement, all complete as per standard design :

19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty
HD-20 grade designation) 560 mm internal diameter
conforming to I.S. 12592, total weight of cover and
frame to be not less than 182 kg. fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) including
centering, shuttering all complete. (Excavation, foot
rests and 12 mm thick cement plaster at the external
surface shall be paid for separately) :

19.11.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 24702.75 Each 24703.00
class designation 7.5
19.11.1.2 With Sewer bricks conforming IS : 4885 1.00 No. 24446.70 Each 24447.00
19.12 Extra depth for circular type manhole 1.22 m internal
dia (at bottom) beyond 1.68 m to 2.29 m :
19.12.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 9861.45 One Running 9861.00
class designation 7.5 Metre

DSR - 2023 IN MS EXCEL Page 198 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.12.2 With Sewer bricks conforming IS : 4885 1.00 m 9674.40 One Running 9674.00
Metre
19.13 Constructing brick masonry circular manhole 1.52 m
internal dia at bottom and 0.56 m dia at top in cement
mortar 1:4 (1 cement : 4 coarse sand) inside cement
plaster 12 mm thick with cement mortar 1:3 (1 cement :
3 coarse sand) finished with a floating coat of neat
cement, foundation concrete 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 40 mm nominal size)
and making necessary channel in cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) finished with a floating coat of neat
cement, all complete as per standard design :

19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty
HD-20 grade designation) 560 mm internal diameter
conforming to I.S. 12592, total weight of cover and
frame to be not less than 182 kg. fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) including
centering, shuttering all complete. (Excavation, foot
rests and 12 mm thick cement plaster at the external
surface shall be paid for separately) :

19.13.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 52969.10 Each 52969.00
class designation 7.5
19.13.1.2 With Sewer bricks conforming IS : 4885 1.00 No. 52266.80 Each 52267.00
19.14 Extra depth for circular type manhole 1.52 m internal
dia (at bottom) beyond 2.30 m :
19.14.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 22771.85 One Running 22772.00
class designation 7.5 Metre
19.14.2 With Sewer bricks conforming IS : 4885 1.00 m 22288.10 One Running 22288.00
Metre
19.15 Providing M.S. foot rests including fixing in manholes
with 20x20x10 cm cement concrete blocks 1:3:6 (1
cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size) as per standard design :

19.15.1 With 20x20 mm square bar 1.00 No. 544.70 Each 545.00
19.15.2 With 20 mm diameter round bar 1.00 No. 496.50 Each 497.00
19.16 Providing orange colour safety foot rest of minimum 6 1.00 No. 553.70 Each 554.00
mm thick plastic encapsulated as per IS : 10910, on 12
mm dia steel bar conforming to IS: 1786, having
minimum cross section as 23 mmx25 mm and over all
minimum length 263 mm and width as 165 mm with
minimum 1 12 mm space between protruded legs
having 2 mm tread on top surface by ribbing or
chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard
drawing and suitable to with stand the bend test and
chemical resistance test as per specifications and having
manufacture's permanent identification mark to be
visible even after fixing, including fixing in manholes
with 30x20x15 cm cement concrete block 1:3:6 (1
cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size) complete as per design.

DSR - 2023 IN MS EXCEL Page 199 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.17 Replacement of M.S. foot rests in manholes including
dismantling concrete blocks and fixing with 20x20x10
cm cement concrete blocks 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size) :

19.17.1 With 20x20 mm square bar 1.00 No. 670.20 Each 670.00
19.17.2 With 20 mm diameter round bar 1.00 No. 621.95 Each 622.00
19.18 Supplying and fixing C.I. cover without frame for
manholes :
19.18.1 455x610 mm rectangular C.I. cover (light duty) the 1.00 No. 1358.00 Each 1358.00
weight of the cover to be not less than 23 kg.
19.18.2 500 mm diameter C.I. cover (medium duty) the weight 1.00 No. 3441.20 Each 3441.00
of the cover to be not less than 58 kg.
19.18.3 560 mm diameter C.I. cover (heavy duty) the weight of 1.00 No. 7575.40 Each 7575.00
the cover to be not less than 108 kg.
19.19 Providing and fixing in position pre-cast R.C.C. manhole
cover and frame of required shape and approved
quality
19.19.1 L D - 2.5
19.19.1.1 Rectangular shape 600x450 mm internal dimensions 1.00 No. 1437.65 Each 1438.00
19.19.1.2 Square shape 450 mm internal dimensions 1.00 No. 1155.45 Each 1155.00
19.19.1.3 Circular shape 450 mm internal diameter 1.00 No. 1169.65 Each 1170.00
19.19.2 M D - 10
19.19.2.1 Square shape 450 mm internal dimension 1.00 No. 1386.55 Each 1387.00
19.19.2.2 Circular shape 500 mm internal diameter 1.00 No. 1172.60 Each 1173.00
19.19.3 H D - 20
19.19.3.1 Circular shape 560 mm internal diameter 1.00 No. 1675.70 Each 1676.00
19.19.4 EHD - 35
19.19.4.1 Circular shape 560 mm internal dia. 1.00 No. 2123.80 Each 2124.00
19.20 Supplying and fixing C.I. cover 300x300 mm without 1.00 No. 787.00 Each 787.00
frame for gully trap (standard pattern) the weight of
cover to be not less than 4.5 kg.
19.21 Making connection of drain or sewer line with existing
manhole including breaking into and making good the
walls, floors with cement concrete 1:2:4 mix (1 cement :
2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) cement plastered on both sides with
cement mortar 1:3 (1 cement : 3 coarse sand) finished
with a floating coat of neat cement and making
necessary channels for the drain etc. complete :

19.21.1 For pipes 100 to 250 mm diameter 1.00 No. 810.45 Each 810.00
19.21.2 For pipes 250 to 300 mm diameter 1.00 No. 922.40 Each 922.00
19.21.3 For pipes 350 to 450 mm diameter 1.00 No. 1328.45 Each 1328.00

DSR - 2023 IN MS EXCEL Page 200 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.22 Providing sand cast iron drop connection externally for
60 cm drop from branch sewer line to main sewer
manhole including inspection and cleaning eye with
chain and lid, sand cast iron drop pipe and bend
encased all-round with cement concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40
mm nominal size) with all centering and shuttering
required, cutting holes in walls and making good with
brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) plastered with cement mortar 1:3 (1 cement : 3
coarse sand) on inside of the manhole wall, lead
caulked joints between sand cast iron pipes and fittings,
stiff cement mortar 1:1 (1 cement : 1 fine sand) joints
between sand cast iron tee and S.W. pipe, making
required channels complete as per standard design and
specifications :

19.22.1 100 mm dia. sand cast iron drop connection 1.00 No. 12172.05 Each 12172.00
19.22.2 150 mm dia. sand cast iron drop connection 1.00 No. 16577.80 Each 16578.00
19.23 Extra for depths beyond 60 cm of sand cast iron drop
connection complete :
19.23.1 For 100 mm dia. sand cast iron drop connection 1.00 m 3240.45 One Running 3240.00
Metre
19.23.2 For 150 mm dia. sand cast iron drop connection 1.00 m 4126.90 One Running 4127.00
Metre
19.24 Dismantling of manhole including R.C.C. top slab, C.I.
cover with frame, including stacking of useful materials
near the site and disposal of unserviceable materials
within 50 m lead as per direction of Engineer-in-
Charge :

19.24.1 Rectangular manhole 90x80 cm and 45 cm deep 1.00 No. 2540.85 Each 2541.00
19.24.2 Rectangular manhole 120x90 cm and 90 cm deep 1.00 No. 4475.50 Each 4476.00
19.24.3 Rectangular arch type manhole 140x90 cm and 2.45 m 1.00 No. 8466.35 Each 8466.00
deep
19.24.4 Circular manhole 122 cm diameter and 1.68 m deep 1.00 No. 6472.40 Each 6472.00
19.25 Extra for depth of manholes dismantled:
19.25.1 Rectangular manhole 90x80 cm and beyond 45 cm 1.00 m 2045.50 One Running 2046.00
depth Metre
19.25.2 Rectangular manhole 120x90 cm and beyond 90 cm 1.00 m 2436.90 One Running 2437.00
depth Metre
19.25.3 Rectangular arch type manhole 140x90 cm and beyond 1.00 m 1975.85 One Running 1976.00
2.45 m depth (up to 4.25 m depth). Metre
19.25.4 Circular manhole 122 cm diameter and beyond 1.68 m 1.00 m 2229.20 One Running 2229.00
depth (up to 2.29 m depth) Metre
19.26 Raising manhole cover and frame slab to required level
including dismantling existing slab and making good the
damage as required (Raising depth of manhole to be
paid separately) :

19.26.1 Rectangular manhole 90x80 cm with rectangular cover 1.00 No. 2625.50 Each 2626.00
600x450 mm of grade LD - 2.5
19.26.2 Rectangular manhole 120x90 cm with circular cover 500 1.00 No. 4168.05 Each 4168.00
mm dia of grade MD - 10
19.26.3 Rectangular manhole 120x90 cm with circular cover 560 1.00 No. 3881.50 Each 3882.00
mm dia of grade HD - 20
19.26.4 Circular manhole 140 cm dia with circular cover 600 1.00 No. 320.15 Each 320.00
mm dia of grade EHD - 35

DSR - 2023 IN MS EXCEL Page 201 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.27 Constructing brick masonry road gully chamber
50x45x60 cm with bricks in cement mortar 1:4 (1
cement : 4 coarse sand) including 500x450 mm pre-cast
R.C.C. horizontal grating with frame complete as per
standard design :

19.27.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 5957.90 Each 5958.00
class designation 7.5
19.28 Constructing brick masonry road gully chamber
45x45x77.5 cm with bricks in cement mortar 1:4 (1
cement : 4 coarse sand ) with pre-cast R.C.C. vertical
grating complete as per standard design :

19.28.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 6889.80 Each 6890.00
class designation 7.5
19.29 Constructing brick masonry road gully chamber
110x50x77.5 cm with bricks in cement mortar 1:4 (1
cement : 4 coarse sand) including 500x450 mm pre-cast
R.C.C. horizontal grating with frame and vertical grating
complete as per standard design :

19.29.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 11520.55 Each 11521.00
class designation 7.5
19.30 Constructing brick masonry chamber for underground
C.I. inspection chamber and bends with bricks in
cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover
with frame (light duty) 455x610 mm internal
dimensions, total weight of cover with frame to be not
less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1
cement : 1.5 fine sand : 3 graded stone aggregate 20
mm nominal size), foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40
mm nominal size), inside plastering 12 mm thick with
cement mortar 1:3 (1 cement : 3 coarse sand), finished
smooth with a floating coat of neat cement on walls
and bed concrete etc. complete as per standard design:

19.30.1 Inside dimensions 455x610 mm and 45 cm deep for

single pipe line :
19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 6937.90 Each 6938.00
class designation 7.5
19.30.2 Inside dimensions 500x700 mm and 45 cm deep for
pipe line with one or two inlets :
19.30.2.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 8150.50 Each 8151.00
class designation 7.5
19.30.3 Inside dimensions 600x850 mm and 45 cm deep for
pipe line with three or more inlets :
19.30.3.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 9594.35 Each 9594.00
class designation 7.5
19.31 Extra for depth beyond 45 cm of brick masonry
chamber :
19.31.1 For 455x610 mm size
19.31.1.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 6117.00 One Running 6117.00
class designation 7.5 Metre
19.31.2 For 500x700 mm size
19.31.2.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 6680.60 One Running 6681.00
class designation 7.5 Metre
19.31.3 For 600x850 mm size
19.31.3.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 m 7789.85 One Running 7790.00
class designation 7.5 Metre

DSR - 2023 IN MS EXCEL Page 202 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45
x 45 cm dry brick honey comb shaft with bricks and
S.W. drain pipe 100 mm diameter, 1.8 m long complete
as per standard design.

19.32.1 With common burnt clay F.P.S. (non modular) bricks of 1.00 No. 26861.90 Each 26862.00
class designation 7.5
19.33 Constructing soak pit 1.20x1.20x1.20 m filled with 1.00 No. 2890.10 Each 2890.00
brickbats including S.W. drain pipe 100 mm diameter
and 1.20 m long complete as per standard design.
19.34 Providing and fixing S.W. intercepting trap in manholes
with stiff mixture of cement mortar 1:1 (1 cement : 1
fine sand) including testing of joints etc. complete :

19.34.1 100 mm dia 1.00 No. 441.40 Each 441.00

19.34.2 150 mm dia 1.00 No. 602.65 Each 603.00
19.35 Providing and laying Non Pressure NP-3 class (Medium
duty) R.C.C. pipes including collars/ spigot jointed with
stiff mixture of cement mortar in the proportion of 1:2
(1 cement : 2 fine sand) including testing of joints etc.
complete

19.35.1 450 mm dia RCC pipes. 1.00 m 2676.55 One Running 2677.00
Metre
19.35.2 600 mm dia RCC pipes. 1.00 m 3401.25 One Running 3401.00
Metre
19.35.3 900 mm dia RCC pipes. 1.00 m 5377.25 One Running 5377.00
Metre
19.35.4 1000 mm dia RCC pipes. (Laying by manual/ mechanical 1.00 m 6656.55 One Running 6657.00
means) Metre
19.35.5 1200 mm dia RCC pipes. (Laying by manual/ mechanical 1.00 m 9126.20 One Running 9126.00
means) Metre
19.35.6 1800 mm dia RCC pipes. (Laying by manual/mechanical 1.00 m 16184.00 One Running 16184.00
means) Metre
19.36 Providing and laying Non Pressure NP-4 class (Heavy
duty) R.C.C. pipes including collars/spigot jointed with
stiff mixture of cement mortar in the proportion of 1:2
(1 cement : 2 fine sand) including testing of joints etc.
complete

19.36.1 450 mm dia RCC pipes. 1.00 m 3053.55 One Running 3054.00
Metre
19.36.2 600 mm dia RCC pipes. 1.00 m 3934.75 One Running 3935.00
Metre
19.36.3 900 mm dia RCC pipes. 1.00 m 7397.40 One Running 7397.00
Metre
19.36.4 1000 mm dia RCC pipes. (Laying by manual/mechanical 1.00 m 9181.75 One Running 9182.00
means) Metre
19.36.5 1200 mm dia RCC pipes. (Laying by manual/mechanical 1.00 m 11119.35 One Running 11119.00
means) Metre
19.36.6 1800 mm dia RCC pipes. (Laying by manual/mechanical 1.00 m 22578.75 One Running 22579.00
means) Metre
Total of the Sub-Head - Drainage : 820929.00
Sub-Head : Pile Work

DSR - 2023 IN MS EXCEL Page 203 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
20.1 Providing, driving with hydraulic piling rigs with power
units and installing driven cast-in-situ reinforced
cement concrete piles of grade M-25 of specified
diameter and length below the pile cap, to carry safe
working load not less than specified, excluding the cost
of steel reinforcement but including the cost of shoe
and the length of pile to be embedded in the pile cap
etc. all complete. (Length of pile for payment shall be
measured from top of shoe to the bottom of pile cap) :

20.1.1 400 mm dia piles 1.00 m 2767.00 One Running 2767.00

Metre
20.1.2 450 mm dia piles 1.00 m 3430.65 One Running 3431.00
Metre
20.1.3 500 mm dia piles 1.00 m 4129.95 One Running 4130.00
Metre
20.1.4 550 mm dia piles 1.00 m 4530.90 One Running 4531.00
Metre
20.1.5 750 mm dia piles 1.00 m 7738.55 One Running 7739.00
Metre
20.1.6 1000 mm dia piles 1.00 m 12748.45 One Running 12748.00
Metre
20.1.7 1200 mm dia piles 1.00 m 16671.05 One Running 16671.00
Metre
20.1.8 1500 mm dia piles 1.00 m 23577.75 One Running 23578.00
Metre
20.2 Boring, providing and installation bored cast-in-situ
reinforced cement concrete piles of grade M-25 of
specified diameter and length below the pile cap, to
carry a safe working load not less than specified,
excluding the cost of steel reinforcement but including
the cost of boring with bentonite solution and
temporary casing of appropriate length for setting out
and removal of same and the length of the pile to be
embedded in the pile cap etc. by percussion drilling
using Direct mud circulation (DMC) or Bailer and chisel
technique by tripod and mechanical Winch Machine all
complete, including removal of excavated earth with all
its lifts and leads (length of pile for payment shall be
measured up to bottom of pile cap).

20.2.1 450 mm dia piles 1.00 m 2278.30 One Running 2278.00

Metre
20.2.2 500mm dia piles 1.00 m 2703.25 One Running 2703.00
Metre
20.2.3 600 mm dia piles 1.00 m 3637.20 One Running 3637.00
Metre
20.2.4 750 mm dia piles 1.00 m 5581.20 One Running 5581.00
Metre

DSR - 2023 IN MS EXCEL Page 204 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
20.2A Boring, providing and installation bored cast-in-situ
reinforced cement concrete piles of grade M-25 of
specified diameter and length below pile cap, to carry a
safe working load not less than specified, excluding the
cost of steel reinforcement but including the cost of
boring with bentonite solution and temporary casing of
appropriate length for setting out and removal of same
and the length of the pile to be embedded in the pile
cap etc. by Crawler mounted, telescopic boom
hydraulic pilling Rig all complete, including removal of
excavated earth with all its lifts and leads (length of pile
for payment shall be measured up to bottom of pile
cap).

Note: Truck Mounted rotary/ TMR / Tubewell boring

machine shall not be used.
20.2A.1 600 mm dia piles. 1.00 m 5386.25 One Running 5386.00
Metre
20.2A.2 750 mm dia piles. 1.00 m 7758.75 One Running 7759.00
Metre
20.2A.3 1000 mm dia piles. 1.00 m 12990.80 One Running 12991.00
Metre
20.2A.4 1200 mm dia piles. 1.00 m 17025.75 One Running 17026.00
Metre
20.2A.5 1500 mm dia piles. 1.00 m 24408.80 One Running 24409.00
Metre
20.3 Boring with hydraulic piling rigs with power units,
Providing and installing cast in situ single under reamed
piles of specified diameter and length below pile cap in
M-25 cement concrete, to carry a safe working load not
less than specified, excluding the cost of steel
reinforcement but including the cost of boring with
bentonite solution and the length of the pile to be
embedded in pile cap etc. all complete. (Length of pile
for payment shall be measured upto the bottom of pile
cap):

20.3.1 300 mm dia piles 1.00 m 3065.60 One Running 3066.00

Metre
20.3.2 400 mm dia piles 1.00 m 3797.30 One Running 3797.00
Metre
20.3.3 450 mm dia. piles 1.00 m 4232.75 One Running 4233.00
Metre
20.3.4 550 mm dia piles 1.00 m 4721.15 One Running 4721.00
Metre
20.4 Extra over single under ream for providing additional
bulbs in under reamed piles ,under specified diameter.
(only the nos. of extra bulbs are to be paid)

20.4.1 300mm dia piles. 1.00 No. 2626.30 Each 2626.00

20.4.2 400mm dia piles. 1.00 No. 2924.45 Each 2924.00
20.4.3 450 mm dia piles. 1.00 No. 3104.20 Each 3104.00
20.4.4 550 mm dia piles. 1.00 No. 3360.15 Each 3360.00

DSR - 2023 IN MS EXCEL Page 205 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
20.5 Providing, driving (with vibrating pile driving hammer
complete with power units & accessories ) and installing
driven Pre-cast reinforced cement concrete piles of
specified diameter and length below the pile cap in M-
25 cement concrete to carry safe working load not less
than specified with a central through preformed hole
with M.S. black pipe of dia, 40 mm for grouting with
cement sand grouting of mix 1:2 (1cement : 2 coarse
sand) under sufficient positive pressure to ensure
complete filling including centring, shuttering, driving
and removing the steel casing pipe and lifting casing
etc. complete but excluding the cost of steel
reinforcement. (Length of pile for payment shall be
measured from top of the shoe to the bottom of pile
cap).

20.5.1 400 mm dia piles. 1.00 m 3727.80 One Running 3728.00

Metre
20.5.2 450 mm dia piles. 1.00 m 4766.25 One Running 4766.00
Metre
20.5.3 500 mm dia piles. 1.00 m 4931.35 One Running 4931.00
Metre
20.5.4 550 mm dia piles. 1.00 m 5633.00 One Running 5633.00
Metre
20.5.5 750 mm dia piles. 1.00 m 10846.80 One Running 10847.00
Metre
20.5.6 1000 mm dia piles. 1.00 m 14946.40 One Running 14946.00
Metre
20.6 Vertical load testing of piles in accordance with IS 2911
(Part IV) including installation of loading platform by
Kentledge/Anchor piles method and preparation of pile
head or construction of test cap and dismantling of test
cap after test etc. complete as per specification & the
direction of Engineer in-charge.

Note:- 1 . Initial and Routine Load test shall not be

carried out by Dynamic method of testing.
Note:-2. Testing agency shall submit the design of
loading platform for the approval of Engineer-in-charge.

20.6.1 Single pile upto 50 tonne safe capacity

20.6.1.1 Initial test. ( Test load 2.5 times the safe capacity) 1.00 Nos 54771.50 Per Test 54772.00
20.6.1.2 Routine test ( Test load 1.5 times the safe capacity) 1.00 Nos 19632.40 Per Test 19632.00
20.6.2 Single pile above 50 tonne and upto 100 tonne safe
capacity
20.6.2.1 Initial test ( Test load 2.5 times the safe capacity) 1.00 Nos 61173.35 Per Test 61173.00
20.6.2.2 Routine test. ( Test load 1.5 times the safe capacity) 1.00 Nos 32436.10 Per Test 32436.00
20.6.3 Group of two or more piles upto 50 tonne safe capacity

20.6.3.1 Initial test ( Test load 2.5 times the safe capacity) 1.00 Nos 70420.50 Per Test 70421.00
20.6.3.2 Routine test ( Test load 1.5 times the safe capacity) 1.00 Nos 40545.15 Per Test 40545.00
20.7 Cyclic vertical load testing of pile in accordance with IS
Code of practice IS: 2911 (part IV) by Kentledge method
including preparation of pile head etc for.
20.7.1 Single pile.
20.7.1.1 Upto 50 tonne safe capacity pile. 1.00 Nos 19632.40 Per Test 19632.00
20.7.1.2 Above 50 tonne and upto 100 tonne safe capacity pile. 1.00 Nos 32436.10 Per Test 32436.00

20.7.2 Group of two or more piles.

20.7.2.1 Upto 400 tonne safe capacity of group 1.00 Nos 40545.15 Per Test 40545.00

DSR - 2023 IN MS EXCEL Page 206 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
20.8 Lateral load testing of single pile in accordance with IS
Code of practice IS : 2911 (Part IV) for determining safe
allowable lateral load on pile :
20.8.1 Upto 50 tonne capacity pile. 1.00 Nos 19632.40 Per Test 19632.00
20.8.2 Above 50 tonne and upto 100 tonne capacity pile. 1.00 Nos 32862.90 Per Test 32863.00
20.9 Integrity testing of Pile using Low Strain/ Sonic Integrity
Test/ Sonic Echo Test method in accordance with IS
14893 including surface preparation of pile top by
removing soil, mud, dust & chipping lean concrete
lumps etc. and use of computerised equipment and
high skill trained personal for conducting the test &
submission of results, all complete as per direction of
Engineer-in-charge.

Note:- The inclusion of the above item in the schedule 1.00 Nos 1153.20 Per Test 1153.00
of work shall be judiciously decided by the technical
sanctioning authority, keeping in view the quality
control, Type of soil strata and importance of the
project.

Total of the Sub-Head - Pile Work : 655287.00

Sub-Head : Aluminium Work
21.1 Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded built
up standard tubular sections/appropriate Z sections and
other sections of approved make conforming to IS: 733
and IS: 1285, fixing with dash fasteners of required dia
and size, including necessary filling up the gaps at
junctions, i.e. at top, bottom and sides with required
EPDM rubber/neoprene gasket etc. Aluminium sections
shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P.
brass/ stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-
in-charge. (Glazing, paneling and dash fasteners to be
paid for separately) :

21.1.1 For fixed portion

21.1.1.1 Anodised aluminium (anodised transparent or dyed to 1.00 Kg 495.05 One Kilogram 495.00
required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
21.1.1.2 Powder coated aluminium (minimum thickness of 1.00 Kg 530.90 One Kilogram 531.00
powder coating 50 micron)
21.1.1.3 Polyester powder coated aluminium (minimum 1.00 Kg 539.85 One Kilogram 540.00
thickness of polyester powder coating 50 micron)
21.1.2 For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making
provision for fixing of fittings wherever required
including the cost of EPDM rubber / neoprene gasket
required (Fittings shall be paid for separately).

21.1.2.1 Anodised aluminium (anodised transparent or dyed to 1.00 Kg 598.60 One Kilogram 599.00
required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
21.1.2.2 Powder coated aluminium (minimum thickness of 1.00 Kg 634.45 One Kilogram 634.00
powder coating 50 micron)
21.1.2.3 Polyester powder coated aluminium (minimum 1.00 Kg 643.45 One Kilogram 643.00
thickness of polyester powder coating 50 micron)

DSR - 2023 IN MS EXCEL Page 207 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
21.2 Providing and fixing 12mm thick prelaminated particle
board flat pressed three layer or graded wood particle
board conforming to IS:12823 Grade l Type ll, in
panelling fixed in aluminum doors, windows shutters
and partition frames with C.P. brass / stainless steel
screws etc. complete as per architectural drawings and
directions of engineer-in-charge.

21.2.1 Pre-laminated particle board with decorative lamination 1.00 Sqm 1139.30 One Square 1139.00
on one side and balancing lamination on other side. Metre

21.2.2 Pre-laminated particle board with decorative lamination 1.00 Sqm 1115.40 One Square 1115.00
on both sides. Metre
21.3 Providing and fixing glazing in aluminium door, window,
ventilator shutters and partitions etc. with EPDM
rubber / neoprene gasket etc. complete as per the
architectural drawings and the directions of engineer-
in-charge . (Cost of aluminium snap beading shall be
paid in basic item):

21.3.1 With float glass panes of 4.0 mm thickness (weight not 1.00 Sqm 1176.80 One Square 1177.00
less than 10 kg/sqm) Metre
21.3.2 With float glass panes of 5 mm thickness (weight not 1.00 Sqm 1505.25 One Square 1505.00
less than 12.50 kg/sqm) Metre
21.3.3 With float glass panes of 8 mm thickness (weight not 1.00 Sqm 1685.40 One Square 1685.00
less than 20 kg/sqm) Metre
21.4 Providing and fixing double action hydraulic floor spring
of approved brand and manufacture conforming to IS :
6315, having brand logo embossed on the body / plate
with double spring mechanism and door weight upto
125 kg., for doors, including cost of cutting
floors ,embedding in floors as required and making
good the same matching to the existing floor finishing
and cover plates with brass pivot and single piece M.S.
sheet outer box with slide plate etc. complete as per
the direction of Engineer-in-charge.

21.4.1 With stainless steel cover plate minimum 1.25 mm 1.00 No. 2823.85 Each 2824.00
thickness.
21.4.2 With brass cover plate minimum 1.25 mm thickness. 1.00 No. 2966.10 Each 2966.00
21.5 Providing and fixing powder coated aluminium work 1.00 Kg 817.15 One Kilogram 817.00
(minimum thickness of powder coating 50 micron)
consisting of tee/ angle sections, of approved make
conforming to IS : 733 in frames of false ceiling
including aluminium angle cleats with necessary C.P.
brass/stainless steel sunk screws, aluminium perimeter
angles fixed to wall with stainless steel rawl plugs @
450 mm centre to centre and fixing the frame work to
G.I. level adjusting hangers 6 mm dia. with necessary
cadmium plated machine screws all complete as per
approved architectural drawings and direction of the
Engineer-in-charge (level adjusting hangers, ceiling
cleats and expansion hold fasteners to be paid for
separately).

21.6 Providing and fixing 6 mm dia. G.I. level adjusting 1.00 No. 82.45 Each 82.00
hangers (upto 1200mm length), fixed to roof slabs by
means of ceiling cleats made out of G.I. flat 40x3mm
size 60 mm long and stainless steel expandable dash
fastener of 12.5 mm dia and 50 mm long, complete as
per direction of Engineer -in-charge.

DSR - 2023 IN MS EXCEL Page 208 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
21.7 Providing and fixing machine moulded aluminium
covering of approved pattern & design, made out of
machine cut aluminium sheet and machine holed for
receiving dash fastener, over expansion joints on
vertical surfaces/ceiling floors, the fixing on plate in one
row on one side of joint only shall be done with
stainless steel dash fasteners of 8mm dia and 75 mm
long bolt including providing aluminium washers 2 mm
thick & 15 mm dia , at a staggered pitch of 200mm
centre to centre including drilling holes in the receiving
surface and providing expandable plastic sleeves in
holes etc. complete as per direction of Engineer-in-
charge.

21.7.1 Anodised aluminium sheet 2.5mm thick (anodised 1.00 Kg 680.55 One Kilogram 681.00
transparent or dyed to required shade according to
IS:1868, Minimum anodic coating of grade AC 15)
21.7.2 Powder coated aluminium sheet 2.5mm thick 1.00 Kg 716.40 One Kilogram 716.00
(minimum thickness of powder coating 50 micron)
21.8 Filling the gap in between aluminium frame & adjacent
RCC/ Brick/ Stone work by providing weather silicon
sealant over backer rod of approved quality as per
architectural drawings and direction of Engineer-in-
charge complete.

21.8.1 Upto 5mm depth and 5 mm width 1.00 m 96.75 One Running 97.00
Metre
21.9 Extra for applying additional anodic coating AC 25
instead of AC 15 to aluminium extruded sections.
21.9.1 For fixed portion 1.00 Kg 12.80 One Kilogram 13.00

21.9.2 For shutters of doors, windows & ventilators. 1.00 Kg 12.80 One Kilogram 13.00

21.10 Providing and fixing double glazed hermetically sealed 1.00 Sqm 4997.70 One Square 4998.00
glazing in aluminium windows, ventilators and partition Metre
etc. with 6 mm thick clear float glass both side, having
12 mm air gap, including providing EPDM gasket,
perforated aluminium spacers, desiccants, sealant (Both
primary and secondary sealant) etc. as per
specifications, drawings and direction of Engineer-in-
charge complete.

21.11 Providing and fixing stainless steel (SS 304 grade)

adjustable friction windows stays of approved quality
with necessary stainless steel screws etc. to the side
hung windows as per direction of Engineer-in-charge
complete.

21.11.1 205 x 19 mm 1.00 No. 344.30 Each 344.00

21.11.2 255 x 19 mm 1.00 No. 387.00 Each 387.00
21.11.3 355 x 19 mm 1.00 No. 325.80 Each 326.00
21.11.4 510 x 19 mm 1.00 No. 802.40 Each 802.00
21.11.5 710 x 19 mm 1.00 No. 1478.15 Each 1478.00
21.12 Providing and fixing aluminium tubular handle bar 32
mm outer dia, 3.0 mm thick & 2100 mm long with SS
screws etc .complete as per direction of Engineer-in-
Charge.

21.12.1 Anodized (AC 15 ) aluminium tubular handle bar 1.00 No. 575.75 Each 576.00
21.12.2 Powder coated minimum thickness 50 micron 1.00 No. 631.55 Each 632.00
aluminium tubular handle bar.
21.12.3 Polyester powder coated minimum thickness 50 micron 1.00 No. 645.50 Each 646.00
aluminium tubular handle bar

DSR - 2023 IN MS EXCEL Page 209 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
21.13 Providing and fixing Brass 100mm mortice latch and 1.00 No. 528.85 Each 529.00
lock with 6 levers without pair of handles (best make of
approved quality) for aluminium doors including
necessary cutting and making good etc. complete.

21.14 Providing and fixing anodised aluminium (anodised 1.00 Kg 402.80 One Kilogram 403.00
transparent or dyed to required shade according to IS:
1868. Minimum anodic coating of grade AC 15) sub
frame work for windows and ventilators with extruded
built up standard tubular sections of approved make
conforming to IS: 733 and IS: 1285, fixed with dash
fastener of required dia and size (Dash fastener to be
paid for separately).

21.15 Providing and fixing aluminium casement windows

fastener of required length for aluminium windows with
necessary screws etc. complete.
21.15.1 Anodized (AC 15) aluminium 1.00 No. 89.40 Each 89.00
21.15.2 Powder coated minimum thickness 50 micron 1.00 No. 97.95 Each 98.00
aluminium.
21.15.3 Polyester powder coated minimum thickness 50 micron 1.00 No. 95.10 Each 95.00
aluminium.
21.16 Providing and fixing aluminium round shape handle of
outer dia 100mm with SS screws etc. complete as per
direction of Engineer-in-charge
21.16.1 Anodized (AC 15 ) aluminium 1.00 No. 107.90 Each 108.00
21.16.2 Powder coated minimum thickness 50 micron 1.00 No. 109.30 Each 109.00
aluminium
21.16.3 Polyester powder coated minimum thickness 50 micron 1.00 No. 112.15 Each 112.00
aluminium.
21.17 Providing and fixing anodised aluminium grill (anodised 1.00 Kg 638.35 One Kilogram 638.00
transparent or dyed to required shade according to IS:
1868 with minimum anodic coating of grade AC 15) of
approved design/pattern, with approved standard
section and fixed to the existing window frame with C.P
brass/ stainless steel screws @ 200mm centre to
centre, including cutting the grill to proper opening size
for fixing and operation of handles and fixing approved
anodised aluminium standard section around the
opening, all complete as per requirement and direction
of Engineer-in-charge. (Only weight of grill to be
measured for payment).

21.18 Providing and fixing 12 mm thick frameless toughened 1.00 Sqm 5325.90 One Square 5326.00
glass door shutter of approved brand and manufacture, Metre
including providing and fixing top & bottom pivot &
double acting hydraulic floor spring type fixing
arrangement and making necessary holes etc. for fixing
required door fittings, all complete as per direction of
Engineer-in-charge (Door handle, lock and stopper etc.
to be paid separately).

21.19 Filling the gap in between aluminium/ stone/ wood

frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/
Gypsum work by providing weather/structural non sag
elastomeric PU sealant over backer rod of approved
quality as per architectural drawings and direction of
Engineer-in-charge complete complying to ASTM C920,
DIN 18540-F & ISO 11600.

21.19.1 Upto 5mm depth and 5 mm width 1.00 m 148.10 One Running 148.00
Metre

DSR - 2023 IN MS EXCEL Page 210 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
21.19.2 Upto 10 mm depth and 10 mm width 1.00 m 200.95 One Running 201.00
Metre
21.19.3 Upto 20 mm depth and 20 mm width 1.00 m 363.20 One Running 363.00
Metre
Total of the Sub-Head - Aluminium Work : 36680.00
Sub-Head : Water Proofing
22.1 Providing and laying integral cement based treatment
for water proofing on horizontal surface at all depth
below ground level for under ground structures as
directed by Engineer-in-Charge and consisting of :

(i) Ist layer of 22 mm to 25 mm thick approved and

specified rough stone slab over a 25 mm thick base of
cement mortar 1:3 (1 cement : 3 coarse sand) including
applying of twice ( at base and top of mortar ) cement
slurry @ 2.2kg/m2 (each time) mixed with water
proofing compound conforming to IS:2645 in the
recommended proportion over the leveling course
(leveling course to be paid separately). Joints sealed
and grouted with cement slurry mixed with water
proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1

cement: 3 coarse sand) mixed with water proofing
compound in recommended proportions.
(iii) Finishing top with stone aggregate of 10 mm to 12
mm nominal size spreading @ 8 cudm/sqm thoroughly
embedded in the 2nd layer.
22.1.1 Using rough kota stone. 1.00 Sqm 1515.60 One Square 1516.00
Metre
22.2 Providing and laying integral cement based treatment
for water proofing on the vertical surface by fixing
specified stone slab 22 mm to 25 mm thick with cement
slurry mixed with water proofing compound conforming
to IS:2645 in recommended proportions with a gap of
20 mm (minimum) between stone slabs and the
receiving surfaces and filling the gaps with neat cement
slurry mixed with water proofing compound and
finishing the exterior of stone slab with cement mortar
1:3 (1 cement : 3 coarse sand) 20 mm thick with neat
cement punning mixed with water proofing compound
in recommended proportion complete at all levels and
as directed by Engineer-in-charge :

22.2.1 Using rough Kota stone 1.00 Sqm 2024.70 One Square 2025.00
Metre
22.3 Providing and laying water proofing treatment to
vertical and horizontal surfaces of depressed portions
of W.C., kitchen and the like consisting of:
(i) Ist course of applying cement slurry @ 4.4 kg/sqm
mixed with water proofing compound conforming to IS
2645 in recommended proportions including rounding
off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement :

3 coarse sand) mixed with water proofing compound in
recommended proportion including rounding off
junction of vertical and horizontal surface.

DSR - 2023 IN MS EXCEL Page 211 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
(iii) IIIrd course of applying blown or residual bitumen
applied hot at 1.7 kg. per sqm of area.
(iv) IVth course of 400 micron thick PVC sheet. 1.00 Sqm 769.60 One Square 770.00
(Overlaps at joints of PVC sheet should be 100 mm wide Metre
and pasted to each other with bitumen @ 1.7 kg/sqm).

22.4 Providing and Placing in position suitable PVC water

stops conforming to IS:12200 for construction/
expansion joints between two RCC members and fixed
to the reinforcement with binding wire before pouring
concrete etc. complete :

22.4.1 Serrated with central bulb (225 mm wide, 8-11 mm 1.00 m 327.65 One Running 328.00
thick) Metre
22.4.2 Dumb bell with central bulb (180 mm wide, 8 mm thick) 1.00 m 267.90 One Running 268.00
Metre
22.4.3 Kickers (320 mm wide, 5 mm thick) 1.00 m 263.65 One Running 264.00
Metre
22.5 Providing and laying water proofing treatment in
sunken portion of WCs, bathroom etc., by applying
cement slurry mixed with water proofing cement
compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed

with water proofing cement compound @ 0.253 kg/
sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm

mixed with water proofing cement compound @ 0.126
kg/sqm. This layer will be allowed to air cure for 4 hours
followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and 1.00 Sqm 617.05 One Square 617.00
sealing of all joints, corners, junctions of pipes and Metre
masonry with polymer mixed slurry.
22.6 Providing and laying water proofing treatment on roofs
of slabs by applying cement slurry mixed with water
proofing cement compound consisting of applying:

(a) after surface preparation, first layer of slurry of

cement @ 0.488 kg/sqm mixed with water proofing
cement compound @ 0.253 kg/sqm.
(b) laying second layer of Fibre glass cloth when the first
layer is still green. Overlaps of joints of fibre cloth
should not be less than 10 cm.
(c) third layer of 1.5 mm thickness consisting of slurry of
cement @ 1.289 kg/sqm mixed with water proofing
cement compound @ 0.670 kg/sqm and coarse sand @
1.289 kg/sqm. This will be allowed to air cure for 4
hours followed by water curing for 48 hours. The entire
treatment will be taken upto 30 cm on parapet wall and
tucked into groove in parapet all around.

(d) fourth and final layer of brick tiling with cement

mortar (which will be paid for separately.
For the purpose of measurement the entire treated 1.00 Sqm 688.90 One Square 689.00
surface will be measured. Metre
22.7 Providing and laying integral cement based water
proofing treatment including preparation of surface as
required for treatment of roofs, balconies, terraces etc
consisting of following operations:

DSR - 2023 IN MS EXCEL Page 212 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
(a) Applying a slurry coat of neat cement using 2.75
kg/sqm of cement admixed with water proofing
compound conforming to IS. 2645 and approved by
Engineer-in-charge over the RCC slab including
adjoining walls upto 300 mm height including cleaning
the surface before treatment.

(b) Laying brick bats with mortar using broken

bricks/brick bats 25 mm to 115 mm size with 50% of
cement mortar 1:5 (1 cement : 5 coarse sand) admixed
with water proofing compound conforming to IS : 2645
and approved by Engineer-in-charge over 20 mm thick
layer of cement mortar of mix 1:5 (1 cement :5 coarse
sand ) admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-
charge to required slope and treating similarly the
adjoining walls upto 300 mm height including rounding
of junctions of walls and slabs.

(c) After two days of proper curing applying a second

coat of cement slurry using 2.75 kg/ sqm of cement
admixed with water proofing compound conforming to
IS : 2645 and approved by Engineerin- charge.

(d) Finishing the surface with 20 mm thick jointless

cement mortar of mix 1:4 (1 cement :4 coarse sand)
admixed with water proofing compound conforming to
IS : 2645 and approved by Engineerin- charge including
laying glass fibre cloth of approved quality in top layer
of plaster and finally finishing the surface with trowel
with neat cement slurry and making pattern of 300x300
mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with

water for a minimum period of two weeks for curing
and for final test.“All above operations to be done in
order and as directed and specified by the Engineer-in-
Charge :

22.7.1 With average thickness of 120 mm and minimum 1.00 Sqm 1684.60 One Square 1685.00
thickness at khurra as 65 mm. Metre
22.8 Providing and laying four courses water proofing
treatment with bitumen felt over roofs consisting of
first and third courses of blown bitumen 85/25 or 90/15
conforming to IS : 702 applied hot @ 1.45 Kg per square
metre of area for each course, second course of roofing
felt type 3 grade-I (hessian based self finished bitumen
felt) and fourth and final course of stone grit 6 mm and
down size or pea sized gravel spread at 6 cubic
decimeter per square metre, including preparation of
surface but excluding grading complete with :

22.8.1 Bitumen felt (hessian base) type 3 grade I conforming 1.00 Sqm 515.05 One Square 515.00
to IS : 1322 Metre

DSR - 2023 IN MS EXCEL Page 213 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
22.9 Providing and laying six courses water proofing 1.00 Sqm 806.45 One Square 806.00
treatment with bitumen felt over roofs consisting of Metre
first, third and fifth course of blown bitumen 85/25 or
90/15 conforming to IS : 702 applied hot @ 1.45, 1.20
and 1.45 Kg per square metre of area respectively,
second and fourth courses of roofing felt type 3 grade I
conforming to IS : 1322 (Hessian based self finished
bitumen felt) , sixth and final course of stone grit 6 mm
and down size or pea sized gravel spread at 6 cubic
decimeter per sqm including preparation of surface but
excluding grading, complete.

22.10 Providing and laying six courses water proofing 1.00 Sqm 910.85 One Square 911.00
treatment with bitumen felt over roofs consisting of Metre
first, third and fifth courses of blown or / and residual
bitumen applied hot at 1.45, 1.20 and 1.70 kg per
square metre of area respectively, second and fourth
courses of roofing felt type 2 grade I (fibre base self
finished bitumen felt) six and final courses of stone grit
6 mm and down size or pea sized gravel spread at 6
cubic decimeter per sqm including preparation of
surface, excluding grading, compete.

22.11 Providing and laying six courses water proofing 1.00 Sqm 910.85 One Square 911.00
treatment with bitumen felt over roofs consisting of Metre
first, third and fifth courses of blown or / and residual
bitumen applied hot at 1.45, 1.20 and 1.70 kg per
square metre of area respectively, second and fourth
courses of roofing felt type 2 grade II (glass fibre base
self finished bitumen felt) and sixth and final course of
stone grit 6 mm and down size or pea sized gravel
spread at 6 cubic decimeter per sqm including
preparation of surface but excluding grading, complete.

22.12 Supplying and applying bituminous solution primer on 1.00 Sqm 59.45 One Square 59.00
roof and / or wall surface at 0.24 litre per sqm. Metre
22.13 Deduct for omitting in water proofing treatment final
course of spreading stone grit 6 mm down size or pea
sized gravel :
22.13.1 at 6 cudm per sqm 1.00 Sqm -17.55 One Square -18.00
Metre
22.13.2 at 8 cudm per sqm 1.00 Sqm -22.10 One Square -22.00
Metre
22.14 Grading roof for water proofing treatment with
22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 1.00 Cum 8042.30 One Cubic 8042.00
graded stone aggregate 20mm nominal size) Metre
22.14.2 Cement mortar 1:3 (1 cement : 3 coarse sand) 1.00 Cum 16112.10 One Cubic 16112.00
Metre
22.14.3 Cement mortar 1:4 (1cement : 4 coarse sand) 1.00 Cum 15155.60 One Cubic 15156.00
Metre

DSR - 2023 IN MS EXCEL Page 214 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
22.22 Providing and mixing integral crystalline admixture for
waterproofing treatment to RCC structures like
basement raft, retaining walls, reservior, sewage &
water treatment plant, tunnels / subway and bridge
deck etc.. at the time of transporting of concrete into
the drum of the ready-mix truck , using integral
crystalline admixture @0.80% (minimum) to the weight
of cement content per cubic meter of concrete) or
higher as recommended by the manufacturer’s
specification in reinforced cement concrete at site of
work.

The material shall meet the requirements as specified in 1.00 Kg 388.00 One Kilogram 388.00
ACI-212-3R- 2010 i.e. by reducing permeability of
concrete by more than 90%, compared with control
concrete as per DIN 1048 and resistant to 16 bar
hydrostatic pressure. The crystalline admixture shall be
capable of self-healing of cracks up to a width of
0.50mm. The work shall be carried out all complete as
per specification and the direction of the Engineer-in-
charge. The product performance shall carry guarantee
for 10 years against any leakage.

22.22A Providing and applying fibre reinforced elastomeric 1.00 Sqm 563.10 One Square 563.00
liquid water proofing membrane with resilient acrylic Metre
polymers having Sun Reflectivity Index (SRI) of 105 on
top of concrete roof in three coats @10.76 litre/ 10
sqm. One coat of self-priming of elastomeric
waterproofing liquid (dilution with water in the ratio of
3:1) and two coats of undiluted elastomeric
waterproofing liquid (dry film thickness of complete
application/system not less than 500 microns). The
operation shall be carried out after scrapping and
properly cleaning the surface to remove loose particles
with wire brushes, complete in all respect as per the
direction of Engineer-in-Charge.

22.23 Providing and applying integral crystalline slurry of

hydrophilic in nature for waterproofing treatment to
the RCC structures like retaining walls of the basement,
water tanks, roof slabs, podiums, reservior, sewage &
water treatment plant, tunnels / subway and bridge
deck etc., prepared by mixing in the ratio of 5 : 2 (5
parts integral crystalline slurry : 2 parts water) for
vertical surfaces and 3 : 1 (3 parts integral crystalline
slurry : 1 part water) for horizontal surfaces and
applying the same from negative (internal) side with the
help of synthetic fiber brush. The material shall meet
the requirements as specified in ACI- 212-3R-2010 i.e by
reducing permeability of concrete by more than 90%
compared with control concrete as per DIN 1048 and
resistant to 16 bar hydrostatic pressure on negative
side. The crystalline slurry shall be capable of self-
healing of cracks up to a width of 0.50mm. The work
shall be carried out all complete as per specification and
the direction of the engineer-in-charge. The product
performance shall carry guarantee for 10 years against
any leakage.

22.23.1 For vertical surface two coats @ 0.70 kg per sqm 1.00 Sqm 472.90 One Square 473.00
Metre

DSR - 2023 IN MS EXCEL Page 215 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
22.23.2 For horizontal surface one coat @1.10 kg per sqm. 1.00 Sqm 362.80 One Square 363.00
Metre
22.23A Providing & Applying polymer modified, flexible 1.00 Sqm 447.35 One Square 447.00
cementatious negative side waterproofing coating with Metre
elastic waterproofing polymers on interior wall plaster
surface in three coats @14.35 kg /10 sqm. one coat of
self priming of cementatious waterproofing
polymer(dilution with water in the ratio of 1:1) and two
coats of cementatious waterproofing polymer (dilution
with water in the ratio of 3:1 ) after scrapping and
properly cleaning the surface to remove pre-existing
paint film & loose particles till plaster is visible,
complete in all respect as per the direction of Engineer-
in-Charge.

22.24 Providing and applying integral crystalline (dry shake) of 1.00 Sqm 309.60 One Square 310.00
hydrophilic in nature for waterproofing treatment to Metre
the RCC structures like basement raft, foundation slab,
sewage & water treatment plant slab, warehouses
floor, parking structures and water tank base slab etc.
sprinkled @0.60kg per sqm or higher as recommended
by the manufacturer’s specification over the lean
concrete of above cited structures. The material shall
meet the requirements as specified in ACI-212-3R-2010
i.e. by reducing permeability of concrete by more than
85%, compared control concrete as per DIN 1048 and
resistant to 16 bar hydrostatic pressure on negative
side. The crystalline dryshake shall be capable of self-
healing of cracks up to a width of 0.50mm. The work
shall be carried out all complete as per specification and
the direction of the Engineer-in-charge. The product
performance shall carry guarantee for 10 years against
any leakage.

22.24A Providing & Applying high quality acrylic modified resin 1.00 Sqm 597.00 One Square 597.00
based texture of Dholpur/Red sand stone Pattern with Metre
anti algae and UV resistance properties to be applied as
intermediate finish in desired pattern @ 43.04 kgs/10
sqm to form film of 1- 1.5 mm thickness after scrapping
and properly cleaning the surface to remove loose
particles from the plaster surface, followed by top
coating with Premium Acrylic Smooth exterior paint
with Silicone additives of required shade by two or
more coats @ 1.43 litres/10 sqm, complete as the
direction of Engineer -in-Charge.

22.25 Providing and applying crystalline mortar by mixing in

the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part
water) for the treatment of faulty construction joints,
cracks, tie rod holes and spalled & honeycombed
surface of RCC underground structures like basement,
water tanks, bridge deck etc. to ensure water tightness.
The crystallie mortar shall conform to the EN 1504-3
having compressive strength Class R4 > 45 MPa and
adhesive bond strength Class R3 > 1.5 MPa. The work
shall be carried out all complete as per specification and
the direction of the Engineer-In-Charge. The product
performance shall carry guarantee for 10 years against
any leakage.

DSR - 2023 IN MS EXCEL Page 216 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
22.25.1 For sealing cracks and faulty construction joints, routed 1.00 m 547.70 One Running 548.00
out/making U-shape groove size 25x25mm and then Metre
primed the area with integral crystalline slurry
@0.05kg/ running metre and while the surface is tacky
filled the groove upto surface with crystalline mortar
@1.50kg/ running metre. Once crystalline mortar is
touch dry then finally applied two coats of integral
crystalline slurry @0.05kg/running meter per coat.

22.25.2 For patching of tie rod holes, prepared tie rod hole 1.00 holes 23.05 Each Hole 23.00
surface and then primed the area with integral
crystalline slurry @0.070kg/sqm and while the surface
is tacky repair and then filled the tie rod holes with
crystalline [email protected] per hole. The crystalline
mortar should be tightly rodded into tie rod holes or
packed tightly (For 25x25x25 mm tie rod hole, use
0.040kg to fill the hole)

22.26 Providing and applying of swellable type water stop 1.00 m 573.45 One Running 573.00
tape, 19mm x 25mm thick in linear meter (expansive Metre
nature) for construction joints treatment of RCC
structure such as raft slab, retaining walls, water
storage tank and at the junctions of raft slab with the
retaining walls etc.. After cleaning the surface, one coat
of required primer for swellable water stop tape shall
be applied throughout the length of the joint @3.78
litre per 240 running meter. Over the primed surface
swellable type water stop tape shall be placed. The
work shall be carried out all complete as per
specification and the direction of the Engineer-In-
Charge. The product performance shall carry guarantee
for 10 years against any leakage.

Total of the Sub-Head - Water Proofing : 54919.00

Sub-Head : Rain Water Harvesting and Tube Well
23.1 Boring/drilling bore well of required dia for casing/
strainer pipe, by suitable method prescribed in IS: 2800
(part I), including collecting samples from different
strata, preparing and submitting strata chart/ bore log,
including hire & running charges of all equipments,
tools, plants & machineries required for the job, all
complete as per direction of Engineer -in-charge, upto
90 metre depth below ground level.

23.1.1 All types of soil

23.1.1.1 300 mm dia 1.00 m 707.75 One Metre 708.00
23.1.1.2 350 mm dia 1.00 m 774.05 One Metre 774.00
23.1.1.3 400 mm dia 1.00 m 990.80 One Metre 991.00
23.1.2 Rocky strata including Boulders
23.1.2.1 300 mm dia 1.00 m 1695.10 One Metre 1695.00
23.1.2.2 350 mm dia 1.00 m 1792.85 One Metre 1793.00
23.1.2.3 400 mm dia 1.00 m 2131.45 One Metre 2131.00
23.2 Boring/drilling bore well of required dia for casing/
strainer pipe, by suitable method prescribed in IS: 2800
(part I), including collecting samples from different
strata, preparing and submitting strata chart/ bore log,
including hire & running charges of all equipments,
tools, plants & machineries required for the job, all
complete as per direction of Engineer -in-charge,
beyond 90 metre & upto 150 metre depth below
ground level.

23.2.1 All types of soil

DSR - 2023 IN MS EXCEL Page 217 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
23.2.1.1 300 mm dia 1.00 m 825.70 One Metre 826.00
23.2.1.2 350 mm dia 1.00 m 917.40 One Metre 917.00
23.2.1.3 400 mm dia 1.00 m 1238.50 One Metre 1239.00
23.2.2 Rocky strata including Boulders
23.2.2.1 300 mm dia 1.00 m 1870.60 One Metre 1871.00
23.2.2.2 350 mm dia 1.00 m 1955.60 One Metre 1956.00
23.2.2.3 400 mm dia 1.00 m 2496.55 One Metre 2497.00
23.3 Supplying, assembling, lowering and fixing in vertical
position in bore well, unplasticized PVC medium well
casing (CM) pipe of required dia, conforming to IS:
12818, including required hire and labour charges,
fittings& accessories etc. all complete, for all depths, as
per direction of Engineer-in-charge.

23.3.1 100 mm nominal size dia 1.00 m 672.30 One Metre 672.00
23.3.2 150 mm nominal size dia 1.00 m 793.25 One Metre 793.00
23.3.3 200 mm nominal size dia 1.00 m 1113.35 One Metre 1113.00
23.4 Supplying, assembling, lowering and fixing in vertical
position in bore well unplasticized PVC medium well
screen (RMS) pipes with ribs, conforming to IS: 12818,
including hire & labour charges, fittings & accessories
etc. all complete, for all depths, as per direction of
Engineer-in-charge.

23.4.1 100 mm nominal size dia 1.00 m 686.55 One Metre 687.00
23.4.2 150 mm nominal size dia 1.00 m 807.45 One Metre 807.00
23.4.3 200 mm nominal size dia 1.00 m 1255.70 One Metre 1256.00
23.5 Supplying, filling, spreading & leveling stone boulders of 1.00 Cum 1509.80 One Cubic 1510.00
size range 5 cm to 20 cm, in recharge pit, in the Metre
required thickness, for all leads & lifts, all complete as
per direction of Engineer-in-charge.

23.6 Supplying, filling, spreading & leveling gravels of size 1.00 Cum 1538.25 One Cubic 1538.00
range 5 mm to 10 mm, in the recharge pit, over the Metre
existing layer of boulders, in required thickness, for all
leads & lifts, all complete as per direction of Engineer-
in-charge.

23.7 Supplying, filling, spreading & leveling coarse sand of 1.00 Cum 1538.25 One Cubic 1538.00
size range 1.5 mm to 2 mm in recharge pit, in required Metre
thickness over gravel layer, for all leads& lifts, all
complete as per direction of Engineer -in-charge.

23.8 Gravel packing in tubewell construction in accordance 1.00 Cum 2024.50 One Cubic 2025.00
with IS: 4097, including providing gravel fine/ medium/ Metre
coarse, in required grading & sizes as per actual
requirement, all complete as per direction of Engineer-
in-charge.

23.9 Providing and fixing factory made precast RCC 1.00 No. 1399.95 Each 1400.00
perforated drain covers, having concrete of strength
not less than M-25, of size 1000 x 450x50 mm,
reinforced with 8 mm dia four nos longitudinal & 9 nos
cross sectional T.M.T. hoop bars, including providing 50
mm dia perforations @ 100 to 125 mm c/c, including
providing edge binding with M.S. flats of size 50 mm x
1.6 mm complete, all as per direction of Engineer-in-
charge.

DSR - 2023 IN MS EXCEL Page 218 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
23.10 Supplying, assembling, lowering and fixing in vertical
position in bore well, ERW (Electric Resistance Welded)
FE 410 mild steel screwed and socketed/ plain ended
casing pipes of required dia, conforming to IS: 4270, of
reputed & approved make, including painted with
outside surface with two coats of anticorrosive paint of
approved brand and manufacture, including required
hire & labour charges, fittings & accessories, all
complete, for all depths, as per direction of Engineer-in-
charge.

23.10.1 100 mm nominal size dia having minimum wall 1.00 m 1359.25 One Metre 1359.00
thickness 5.00 mm
23.10.2 150 mm nominal size dia having minimum wall 1.00 m 1972.25 One Metre 1972.00
thickness 5.00 mm
23.10.3 200 mm nominal size dia having minimum wall 1.00 m 2442.75 One Metre 2443.00
thickness 5.40 mm
23.11 Supplying, assembling, lowering and fixing in vertical
position in bore well, ERW (Electric Resistance Welded)
FE 410 plain slotted (having slot of size 1.6/3.2 mm)
mild steel threaded and socketed / plain bevel ended
pipe (type A) of required dia, conforming to IS: 8110, of
reputed and approved make, having wall thickness not
less than 5.40 mm, including painted with outside
surface with two coats of anticorrosive bitumastic paint
of approved brand and manufacture, including hire &
labour charges, fittings & accessories, all complete, for
all depths, as per direction of Engineer -in-charge.

23.11.1 100 mm nominal size dia 1.00 m 1456.80 One Metre 1457.00
23.11.2 150 mm nominal size dia 1.00 m 2102.25 One Metre 2102.00
23.11.3 200 mm nominal size dia 1.00 m 2571.05 One Metre 2571.00
23.12 Development of tube well in accordance with IS : 2800 1.00 hour 1085.05 One Hour 1085.00
(part I) and IS:11189, to establish maximum rate of
usable water yield without sand content (beyond
permissible limit), with required capacity air
compressor, running the compressor for required time
till well is fully developed, measuring yield of well by
“V” notch method or any other approved method,
measuring static level & draw down etc. by step draw
down method, collecting water samples & getting
tested in approved laboratory, i/c disinfection of
tubewell, all complete, including hire & labour charges
of air compressor, tools & accessories etc., all as per
requirement and direction of Engineer-in-charge.

23.13 Providing and fixing suitable size threaded mild steel

cap or spot welded plate to the top of bore well
housing/ casing pipe, removable as per requirement, all
complete for bore well of:

23.13.1 100 mm dia 1.00 No. 224.10 Each 224.00

23.13.2 150 mm dia 1.00 No. 246.45 Each 246.00
23.13.3 200 mm dia 1.00 No. 321.15 Each 321.00
23.14 Providing and fixing M.S. clamp of required dia to the
top of casing/ housing pipe of tubewell as per IS: 2800
(part I), including necessary bolts & nuts of required size
complete.

23.14.1 100 mm clamp 1.00 No. 1911.40 Each 1911.00

23.14.2 150 mm clamp 1.00 No. 2019.05 Each 2019.00
23.14.3 200 mm clamp 1.00 No. 2293.65 Each 2294.00

DSR - 2023 IN MS EXCEL Page 219 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
23.15 Providing and fixing Bail plug/ Bottom plug of required
dia to the bottom of pipe assembly of tubewell as per
IS:2800 (part I).
23.15.1 100 mm dia 1.00 No. 265.10 Each 265.00
23.15.2 150 mm dia 1.00 No. 322.00 Each 322.00
23.15.3 200 mm dia 1.00 No. 357.60 Each 358.00
Total of the Sub-Head - Rain Water Harvesting And Tube Well : 51686.00
Sub-Head : Conservation of Heritage Buildings
24.1 Raking out joints of stone masonry surface to the 1.00 Sqm 72.45 One Square 72.00
required width and depth, with due care and Metre
precaution, by mechanical / manual means, including
preparing and cleaning the surface for re-pointing/
refilling of joints, including disposal of rubbish to the
dumping ground within 50 metre lead.

24.2 Providing and fixing double scaffolding system (cup lock

type) on the exterior side of building/structure, upto 25
metre height, above ground level, including additional
rows of scaffolding in stepped manner as per
requirement of site, made with 40mm dia M.S. tube,
placed 1.5 metre centre to centre, horizontal & vertical
tubes joint with cup & lock system with M.S. Tubes,
M.S. tube challis, M.S. clamps and staircase system in
the scaffolding for working platform etc. and
maintaining it in a serviceable condition for execution
of work of cleaning and/ or pointing and/ or applying
chemical and removing it thereafter.

The scaffolding system shall be stiffened with bracings,

runners, connecting with the building etc, wherever
required, if feasible, for inspection of work at required
locations with essential safety features for the
workmen etc., complete as per directions and approval
of Engineer-in-charge.

Note :- (1) The elevational area of the scaffolding shall

be measured for payment purpose.
(2) The payment will be made once only for execution 1.00 Sqm 338.25 One Square 338.00
of all items for such works. Metre
24.3 Cleaning the sand stone surface and removing dirt, 1.00 Sqm 211.05 One Square 211.00
dust, bird dropping, grease, oil, algae, fungus, monkey Metre
beats, vegetable growth etc., including providing,
applying and washing the surface with liquid Ammonia
Chemical of 5% solution and other chemical cleaning
agent as approved by Archaeological Survey of India/
Engineer-in-charge, of approved brand and
manufacturer, with the help of required scrubbers and
also cleaning with machine operated water jet mixed
with desired quantity of fine silica where ever required,
without causing any scratching/ damage to the stone
surface and finally washing the surface with clean water
with the help of pressure jet machine, complete in all
respect, including taking all precautions to safeguard
ventilators, windows, doors etc. by suitable covering so
as to avoid any damage to the building/structure, all as
per direction of Engineerin- charge (The rate is inclusive
of all materials & labours involved except scaffolding).

DSR - 2023 IN MS EXCEL Page 220 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
24.4 Providing and applying antifungal wash treatment using 1.00 Sqm 77.90 One Square 78.00
3% solution of sodium pentachlorophenate, of reputed Metre
brand and manufacturer, on cleaned sand stone surface
at desired locations as per direction of Engineer-in-
charge (The rate is inclusive of all materials & labours
involved except scaffolding).

24.5 Ruled / Flush pointing on Red sand stone masonry 1.00 Sqm 374.30 One Square 374.00
surface with lime, surkhi and marble dust mortar in the Metre
ratio of 1:1.5:1/2 {One lime: 1.5 surkhi (50% red and
50% light yellow surkhi ) : 1/2 marble dust}. (The rate is
inclusive of all materials & labours involved except
scaffolding).

24.6 Ruled/ Flush pointing on White sand stone masonry 1.00 Sqm 374.30 One Square 374.00
surface with lime, surkhi and marble dust mortar in the Metre
ratio of 1:1.5:1/2 {One lime : 1.5 surkhi (15% dark red
and 85% light yellow surkhi) : 1/2 marble dust}. (The
rate is inclusive of all materials & labours involved
except scaffolding).

24.7 Applying two or more coat of Ethyl Silicate chemical as 1.00 Sqm 329.05 One Square 329.00
approved by Archaeological Survey of India/ Engineer- Metre
in-charge, of approved brand and manufacturer, with
brush or spray on the existing stone masonry surface till
there is no further absorption of chemical by stone
surface, including protecting the applied surface from
direct sunlight by suitable means during application, all
complete as per direction of the Engineer-in-Charge
(The rate is inclusive of all materials & labours involved
except scaffolding).

24.8 Applying breathable, non-reactive, antifungal, and 1.00 Sqm 109.90 One Square 110.00
water repellant Silane/ Siloxane chemical as approved Metre
by Archaeological Survey of India/ Engineer-in-charge,
of approved brand and manufacture, diluted with
solvent mineral Turpentine oil in the ratio of 1:12 (One
part of approved chemical :12 Part of Turpentine oil),
on the existing sand stone masonry surface with two or
more coats to give uniform application of chemical on
the surface, all complete as per direction of Engineer-
In-charge (The rate is inclusive of all materials & labours
involved except scaffolding).

Total of the Sub-Head - Conservation Of Heritage Buildings : 1886.00

Sub-Head : Structural Glazing and Aluminium Composite Panels
25.1 Providing and supplying aluminium extruded tubular 1.00 Kg 414.30 One Kilogram 414.00
and other aluminium sections as per the architectural
drawings and approved shop drawings , the aluminium
quality as per grade 6063 T5 or T6 as per BS 1474,
including super durable powder coating of 60-80
microns conforming to AAMA 2604 of required colour
and shade as approved by the Engineer-in-Charge. (The
item includes cost of material such as cleats, sleeves,
screws etc. necessary for fabrication of extruded
aluminium frame work. Nothing extra shall be paid on
this account). The weight of aluminium extruded
section shall be taken for purpose of payment.

DSR - 2023 IN MS EXCEL Page 221 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
25.2 Designing, fabricating, testing, protection, installing and
fixing in position semi (grid) unitized system of
structural glazing (with open joints) for linear as well as
curvilinear portions of the building for all heights and all
levels including:

a) Structural analysis & design and preparation of shop

drawings for the specified design loads conforming to IS
875 part III (the system must passed the proof test at
1.5 times design wind pressure without any failure),
including functional design of the aluminum sections for
fixing glazing panels of various thicknesses, aluminium
cleats, sleeves and splice plates etc. gaskets, screws,
toggles, nuts, bolts, clamps etc., structural and weather
silicone sealants, flashings, fire stop (barrier)-cum-
smoke seals, microwave cured EPDM gaskets for water
tightness, pressure equalisation & drainage and
protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip

galvanised / Aluminium alloy of 6005 T5 brackets of
required sizes, sections and profiles etc. to
accommodate 3 Dimensional movement for achieving
perfect verticality and fixing structural glazing system
rigidly to the RCC/ masonry/structural steel framework
of building structure using stainless steel anchor
fasteners/ bolts, nylon separator to prevent bimetallic
contacts with nuts and washers etc. of stainless steel
grade 316, of the required capacity and in required
numbers.

c) Providing and filling, two part pump filled, structural

silicone sealant and one part weather silicone sealant
compatible with the structural silicone sealant of
required bite size in a clean and controlled factory /
work shop environment , including double sided spacer
tape, setting blocks and backer rod, all of approved
grade, brand and manufacture, as per the approved
sealant design, within and all around the perimeter for
holding glass.

d) Providing and fixing in position flashings of solid

aluminium sheet 1 mm thick and of sizes, shapes and
profiles, as required as per the site conditions, to seal
the gap between the building structure and all its
interfaces with curtain glazing to make it watertight.

DSR - 2023 IN MS EXCEL Page 222 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
e) Making provision for drainage of moisture/ water
that enters the curtain glazing system to make it
watertight, by incorporating principles of pressure
equalization, providing suitable gutter profiles at
bottom (if required), making necessary holes of
required sizes and of required numbers etc. complete.
This item includes cost of all inputs of designing, labour
for fabricating and installation of aluminium grid,
installation of glazed units, T&P, scaffolding and other
incidental charges including wastages etc., enabling
temporary structures and services, cranes or cradles
etc. as described above and as specified. The item
includes the cost of getting all the structural and
functional design including shop drawings checked by a
structural designer, dully approved by Engineer-in-
charge. The item also includes the cost of all mock ups
at site, cost of all samples of the individual components
for testing in an approved laboratory, field tests on the
assembled working structural glazing as specified,
cleaning and protection till the handing over of the
building for occupation.

In the end, the Contractor shall provide a water tight

structural glazing having all the performance
characteristics etc. all complete as required, as per the
Architectural drawings, as per item description, as
specified, as per the approved shop drawings and as
directed by the Engineer-in-Charge.

Note:- 1. The cost of providing extruded aluminium

frames, shadow boxes, extruded aluminium section
capping for fixing in the grooves of the curtain glazing
and vermin proof stainless steel wire mesh shall be paid
for separately under relevant items under this sub-
head. However, for the purpose of payment, only the
actual area of structural glazing (including width of
grooves ) on the external face shall be measured in
sqm. up to two decimal places.

Note:- 2. The following performance test are to be

conducted on structural glazing system if area of
structural glazing exceeds 2500 Sqm from the certified
laboratories accreditated by NABL (National
Accreditation Board for Testing and Calibration
Laboratories), Department of Science & Technologies,
India. Cost of testing is payable separately. The NIT
approving authority will decide the necessity of testing
on the basis of cost of the work, cost of the test and
importance of the work. Performance Testing of
Structural glazing system Tests to be conducted in the
NBL accredited lab or any other accredition body which
operates in accordance with ISO/IEC 17011 and
accredits labs as per ISO/IEC 17025

(1) Performance Laboratory Test for Air Leakage Test (-

50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-
283-04 testing method for a range of testing limit 1 to
200 mVhr

DSR - 2023 IN MS EXCEL Page 223 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
(2) Static Water Penetration Test. (50pa to 1500pa) as
per ASTME- 331-09 testing method for a range up to
2000 ml.
(3) Dynamic Water Penetration (50pa to 1500pa) as per
AAMA 501.01- 05 testing method for a range upto 2000
ml
(4) Structural Performance Deflection and deformation
by static air pressure test (1.5 times design wind
pressure without any failure) as per ASTME-330-10
testing method for a range upto 50 mm

(5) Seismic Movement Test (upto 30 mm) as per AAMA

501.4-09 testing method for Qualitative test. Tests to
be conducted on site.
(6) Onsite Test for Water Leakage for a pressure range 1.00 Sqm 3510.50 One Square 3511.00
50 kpa to 240 kpa (35psi) upto 2000 ml Metre
25.3 Providing, assembling and supplying vision glass panels
(IGUs) comprising of hermetically-sealed 6-12- 6 mm
insulated glass (double glazed) vision panel units of size
and shape as required and specified, comprising of an
outer heat strengthened float glass 6mm thick, of
approved colour and shade with reflective soft coating
on surface # 2 of approved colour and shade, an inner
Heat strengthened clear float glass 6mm thick, spacer
tube 12mm wide, desiccants, including primary seal and
secondary seal (structural silicone sealant) etc., all
complete for the required performances, as per the
Architectural drawings, as per the approved shop
drawings, as specified and as directed by the Engineer-
in-Charge.

The IGUs shall be assembled in the factory/ workshop

of the glass processor. (Payment for fixing of IGU Panels
in the curtain glazing is included in cost of item No.25.2)
For payment, only the actual area of glass on face # 1 of
the glass panels (excluding the areas of the grooves and
weather silicone sealant) provided and fixed in position,
shall be measured in sqm.

(i) Coloured tinted float glass 6mm thick substrate with 1.00 Sqm 3718.70 One Square 3719.00
reflective soft coating on face # 2, + 12mm Air gap + Metre
6mm Heat Strengthened clear Glass of approved make
having properties as visible Light transmittance (VLT) of
25 to 35 %, Light reflection internal 10 to 15%, light
reflection external 10 to 20%, shading coefficient (0.25-
0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The
properties of performance glass shall be decided by the
technical sanctioning authority as per the site
requirement.

25.4 Extra for openable side / top hung vision glass panels 1.00 Sqm 3671.50 One Square 3672.00
(IGUs) including providing and supplying at site all Metre
accessories and hardwares for the openable panels as
specified and of the approved make such as heavy duty
stainless steel friction hinges, min 4 -point cremone
locking sets with stainless steel plates, handles, buffers
etc. including necessary stainless steel screws/
fasteners, nuts, bolts, washers etc., all complete as per
the Architectural drawings, as per the approved shop
drawings, as specified and as directed by the Engineer-
in- Charge.

DSR - 2023 IN MS EXCEL Page 224 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
25.5 Providing, fabricating and supplying shadow box of
required size and shape, for fixing in the spandrel
portion of the structural glazing, in linear as well as
curvilinear portions of the building by providing semi -
rigid, inorganic, non-combustible fibre glass wool
insulation 50 mm thick, conforming to IS: 8183 and BS:
3958 Part 5.

The insulation layer shall have facing (factory bonded 1.00 Sqm 2159.65 One Square 2160.00
on surface # 1of the fibre glass insulation layer), of black Metre
non-woven fibre glass tissue of nominal thickness 0.5
mm and nominal mass not less than 60 gm / sqm, made
of randomly oriented glass fibres distributed in a binder
by a wet-lay process including fixing 1.5 mm thick solid
aluminum sheet backing using, 6 mm thick cement
board including SS rivets, nuts, bolts, washers etc
complete.

25.6 Providing and supplying Spandrel Glass Panels

comprising of 6 mm thick heat strengthened monolithic
float glass of approved colour and shade with reflective
soft coating on surface # 2 of approved colour and
shade so as to match the colour and shade of the IGUs
in the vision panels etc. ,all complete for the required
performances as specified, as per the Architectural
drawings, as per the approved shop drawings, as
specified, and as directed by the Engineer- in- Charge.

For payment, only the actual area of glass on face # 1 of

the glass panels (but excluding the area of grooves and
weather silicone sealant) provided and fixed in position,
shall be measured in sqm.

(Payment for fixing of Spandrel Glass Panels in the

curtain glazing is included in cost of relevant Item*).
(i) Coloured tinted float glass 6mm thick substrate with 1.00 Sqm 2450.15 One Square 2450.00
reflective soft coating on face # 2, having properties as Metre
visible Light transmittance (VLT) of 25 to 35 %, Light
reflection internal 10 to 15%, light reflection external 10
to 20%, shading coefficient (0.25- 0.28) and U value of
3.0 to 3.3 W/m2 K etc. The properties of performance
glass shall be decided by the technical sanctioning
authority as per the site requirement.

25.8 Design supply & installation of suspended Spider 1.00 Sqm 9502.35 One Square 9502.00
Glazing system designed to withstand the wind Metre
pressure as per IS 875 (Part-III). The Suspended System
held with Spider Fittings of SS-316 Grade Steel of
approved manufacturer with glass panel having 12 mm
thick clear toughened glass held together with SS- 316
Grade Stainless steel Spider & bolt assembly with
laminated glass fins 21 mm thick. The Glass fins and
glass panel assembly shall be connected to Slab/beams
by means of SS- 316 Grade stainless steel brackets &
Anchor bolts and at the bottom using SS channel of
50x25x2mm using fastener & anchor bolts, non staining
weather sealants of approved make, Teflon/ nylon
bushes and separators to prevent bi-metallic contacts,
all complete to perform as per specification and
approved drawings.

DSR - 2023 IN MS EXCEL Page 225 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
The complete system to be designed to accommodate
thermal expansion & seismic movements etc. The joints
between glass panels (6 to 8 mm) and gaps at the
perimeter & in U channel of the assembly to be filled
with non staining weather sealant, so as to make the
entire system fully water proof & dust proof.

The rate shall include all design, Engineering and shop

drawing including approval from structural designer,
labour, T&P, scaffolding , other incidental charges
including wastage, enabling temporary services all
fitting fixers nut bolts, washer, Buffer plates, fastener,
anchors, SS channel laminated glass etc. all complete.
For the purpose of payment, actual elevation area of
Glazing including thickness of joints and the portion of
Glass panel inside the SS channel shall be measured.

Total of the Sub-Head - Structural Glazing And Aluminium Co : 25428.00

Sub-Head : New Technologies and Materials
26.1 Providing & fixing in position Phenol bonded
Bamboowood flooring with planks of sizes 14mm thick,
1800mm length (minimum) and 130 mm
wide(minimum), in approved colour, texture and finish,
having Performance Appraisal Certificate (PAC) issued
by Building Materials & Technology Promotion Council
(BMTPC).

The flooring shall be fixed with tongue and groove 1.00 Sqm 6145.85 One Square 6146.00
interlocking system, with underlayment of 4mm thick Metre
expanded polyethylene foam sheets having density
40kg/cum, over prepared surface with necessary
quarter round planks of size 1900mm x 18mm and door
reducer of size 1900mm x 44mm, wherever required.
The bamboowood planks shall have minimum density
of 1000 Kg/cum & minimum Hardness 1000 Kgf. with
Eco friendly UV coating, all complete as per direction of
the Engineer in-charge.

26.2 Providing & fixing in position Phenol bonded 1.00 Sqm 6033.55 One Square 6034.00
Bamboowood in wall skirting with planks of sizes 14mm Metre
thick, 1900mm length (minimum) and 85mm
wide(minimum), in approved colour, texture and finish,
having Performance Appraisal Certificate (PAC) issued
by Building Materials & Technology Promotion Council
(BMTPC). The skirting shall be fixed with SS screws &
rawl plugs, over underlayment of 4mm thick, expanded
polyethylene foam sheets having 40kg/cum density
over prepared surface. The bamboowood planks shall
have minimum density of 1000Kg/cum & minimum
Hardness 1000 Kgf. with Eco friendly UV coating, all
complete as per direction of the Engineer in-charge.

DSR - 2023 IN MS EXCEL Page 226 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.3 Providing & fixing in position Phenol bonded 1.00 Sqm 6283.85 One Square 6284.00
Bamboowood in wall cladidng at all heights with planks Metre
of sizes 10 mm thick, minimum 1800 mm length and
minimum 100 mm wide, in approved colour, texture
and finish, having Performance Appraisal Certificate
(PAC) issued by Building Materials & Technology
Promotion Council (BMTPC), with necessary profiled
edges fixed with40 mm SS Screws 5 nos in each tile to
framework made of second class teakwood of size 20 x
15 mm in centre of each tile and bottom & top of work
height, 40 x 15 mm placed at end of each tile> The
cladding shall be laid over back layment of 1.00 mm
thick expanded polythyline foam of density 40 kg/sqm
in two layers, first layer on wall surface before fixing
wooden frame and second layer on frame under
cladding. The bamboowood planks shall have minimum
density of 1000Kg/cum & minimum Hardness 1000 Kgf.
with Eco friendly UV coating, all complete as per
direction of the Engineer in-charge.

26.4 Providing & fixing in position Phenol bonded 1.00 Sqm 6935.75 One Square 6936.00
Bamboowood panelled or panelled and glazed shutters Metre
for doors windows, clerestorey windows with pre-
molded 30mm thick planks, in approved colours,
texture & finish. It shall have 10mm wide, 25mm deep
groove to fit in panels. The bamboo wood shall have
minimum density of 1000 Kg/ cum, minimum Hardness
1000 Kgf. All styles and rails shall have profiled
interlocking system locked in place by bamboo pins, all
complete as per direction of Engineer in charge. (The
panelling will be paid for separately).

26.5 Providing & fixing in position Phenol bonded 1.00 Sqm 4555.75 One Square 4556.00
Bamboowood panelling of 10mm thick, in 25 to 40 mm Metre
thick panelled or panelled & glazed shutters for doors,
windows, clerestorey windows, in approved colour,
texture & finish. The bamboowood planks shall have
minimum density of 1000 Kg/cum & minimum Hardness
1000 Kgf. The panels shall have profiled interlocking
system locked in place with bamboo pins all complete
as per direction of the Engineer in-charge. (area of
opening for panel inserts excluding portion inside
grooves or rebates to be measured)

26.6 Providing & fixing in position 65 mm thick factory made 1.00 Cu. D 325.95 One Cubic 326.00
door frame of Phenol bonded Bamboo wood (superior Decimetre
class, interior use), in approved colour, texture and
finish. The bamboo wood shall have minimum density
of 1000 Kg/cum, minimum hardness 1000 Kgf. The door
frame shall have tenon & mortise interlocking system,
to be fixed to the wall with 100 mm size G.I screws all a
complete as per direction of Engineer-in charge.

DSR - 2023 IN MS EXCEL Page 227 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.6A Providing, erecting, laying and fixing in position in 3.5 to 1.00 Sqm 6012.10 One Square 6012.00
4 mm thick bamboo mat corrugated sheet (BMCS) as Metre
per IS: 15476-2004 in roofing with self drilling screws
along with EPDM washers complete or with galvanized
iron J or L hooks 8mm dia G.I. plain and bitumen
washers etc, all complete as per direction of Engineer-
in-Charge.

26.6B Providing and fixing in position ridges of 3.5 to 4 mm 1.00 m 4830.10 One Metre 4830.00
thick bamboo mat ridge cap (BMRC) as per IS: 15476-
2004 in roofing with self drilling screws along with
EPDM washers complete or with galvanized iron J or L
hooks 8mm dia G.I. plain and bitumen washers etc, all
complete as per direction of Engineer-in- Charge.

26.6C Providing and fixing at all height false ceiling of 4mm 1.00 Sqm 4039.10 One Square 4039.00
thick phenol bonded Bamboo Mat board (595x595mm) Metre
conforming to IS:13958-1994 including providing and
fixing of frame work made of GI angle 25x25x0.4 mm
thick all around suitably fixed to wall with the help of
dash fastener and hanger frame (600x600 c/c) made GI
slotted Tee having powder coating on bottom side
(30x25x0.3 mm thick for main member & 25x25x0.3
mm for cross member) connected to ceiling with
2.64mm GI wire and anchor fastener at every junction
and also including cost of making openings for light
fittings, grills, diffusers, cut outs made with frame of
perimeter channels suitably fixed all complete as per
direction of Engineer-in-charge.

26.6D Providing and fixing at Bamboo Mat board conforming

to IS:13958-1994 for partition to frame by bucking or
studding with screws etc. complete (Frames, backing or
studding to be paid separately)

26.6D.1 3 mm thickness 1.00 Sqm 2942.00 One Square 2942.00

Metre
26.6D.2 4 mm thickness 1.00 Sqm 3332.00 One Square 3332.00
Metre
26.6D.3 6 mm thickness 1.00 Sqm 3923.65 One Square 3924.00
Metre
26.6D.4 9 mm thickness 1.00 Sqm 4906.80 One Square 4907.00
Metre
26.6D.5 12 mm thickness 1.00 Sqm 5601.55 One Square 5602.00
Metre
26.6E Providing and fixing at all height wall panelling with
phenol bonded Bamboo Mat board conforming to
IS:13958-1994 including providing and fixing to frame
work made of 50mm x 50mm hardwood plugs including
cutting brick work and fixing in cement mortar and
making good the wall etc. and also providing and fixing
wooden moulded corner beading of triangular shape to
the junction of panelling etc. with iron screws all
complete as per direction of Engineer-in-Charge.

26.6E.1 9 mm thickness 1.00 Sqm 5127.60 One Square 5128.00

Metre
26.6E.2 12 mm thickness 1.00 Sqm 5824.10 One Square 5824.00
Metre

DSR - 2023 IN MS EXCEL Page 228 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.7 Providing and fixing 50 mm thick extruded polystyrene 1.00 Sqm 1004.55 One Square 1005.00
rigid insulation board of required size between cavity Metre
wall, complying with ISO 4898:2008 & ASTM C 578-08b
- type VI, having thermal conductivity of 0.0289 W/m K
as per ASTM C 578 (measured as per IS 3346),
compressive strength of > 350 kPa listed as per ASTM D
1621, density of 34-36 kg/m³ as per ASTM D 1622,
water absorptions < 1% by volume as per ASTM D 2842,
oxygen index of 24.1 to 28.1 listed as per ASTM D 2863,
cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire
retardent property as per DIN 4102, Part 1 of class B2
and as per ASTM E84 class A, fixed with suitable water
based adhesive and fastener, complete in all respect as
per the direction of Engineer- in-Charge.

26.8 Providing and fixing 50 mm thick extruded polystyrene 1.00 Sqm 1091.65 One Square 1092.00
rigid insulation board of required size underdeck on Metre
ceiling surface, complying with ISO 4898:2008 & ASTM
C 578-08b - type VI, having thermal conductivity of
0.0289 W/m K as per ASTM C 578 (measured as per IS
3346), compressive strength of > 350 kPa listed as per
ASTM D 1621, density of 34-36 kg/cum as per ASTM D
1622, water absorptions < 1% by volume as per ASTM D
2842, oxygen index of 24.1 to 28.1 listed as per ASTM D
2863, cell size 0.4 mm of dia (max) as per ASTM D 3576.
Fire retardent property as per DIN 4102, Part 1 of class
B2 and as per ASTM E84 class A, fixed with suitable
water based adhesive and fastener, complete in all
respect as per the direction of Engineer-in-Charge.

26.9 Providing and fixing factory made solid Foam uPVC 1.00 m 450.95 One Metre 451.00
profile for kitchen cabinet frame (45 x 20 mm) of
approved shade, quality and make. The profile shall be
laminated on both sides, made from rigid foam sheets
(Single extruded) having density 600 Kg/cum and the
exposed edges sealed with PVC edge beading of same
shade and colour. The frame shall be fire retardent with
necessary screw holding capacity. Frame shall be fixed
to wall using Expendable Fastner with necesary
stainless steel screws, all complete as per direction of
Engineer-in-charge.

26.10 Providing and fixing factory made Kitchen Cabinet 1.00 Sqm 5350.55 One Square 5351.00
Shutter /Partition 20 mm nominal thickness of Metre
approved shade, quality and make, made from rigid
foam sheets (Single extruded) having density 600
Kg/cum and laminated on both side by laminate Sheet/
PVC foil lamination. The exposed edges shall be sealed
with PVC edge beading of same shade and colour. The
shutter shall be fire retardent having necessary screw
holding capacity. Shutter shall be fixed to frame using
approved hinges with necessary stainless steel screws,
all complete as per direction of Engineer-in-charge.

26.11 Providing and fixing concealed hinge of approved 1.00 No. 144.05 Each 144.00
quality for 19-20mm thick door with stainless steel
screws complete :

DSR - 2023 IN MS EXCEL Page 229 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.12 Supplying & laying of bi-axial extruded high modulus 1.00 Sqm 249.90 One Square 250.00
polypropylene geogrid coforming to MORTH Metre
SPECIFICATION for base/ sub-base reinforcement
having minimum tensile strength 15kN/m in the
longitudinal and transverse direction, with 5kN/m and
7kN/m tensile strength at 2% and 5% strain respectively
in the longitudinal and transverse direction, junction
efficiency not less than 95% and with 38mm X 38mm
mesh opening.

26.13 Supplying & laying of bi-axial extruded high modulus 1.00 Sqm 276.50 One Square 277.00
polypropylene geogrid coforming to MORTH Metre
SPECIFICATION for base/sub-base reinforcement having
minimum tensile strength 20kN/m in the longitudinal
and transverse direction, with 7kN/m and 14kN/m
tensile strength at 2% and 5% strain respectively in the
longitudinal and transverse direction, junction efficiency
not less than 95% and with 38mm X 38mm mesh
opening.

26.14 Supplying & laying of bi-axial extruded high modulus 1.00 Sqm 401.70 One Square 402.00
polypropylene geogrid coforming to MORTH Metre
SPECIFICATION for base/sub-base reinforcement having
minimum tensile strength 30kN/m in the longitudinal
and transverse direction, with 10.5kN/m and 21kN/m
tensile strength at 2% and 5% strain respectively in the
longitudinal and transverse direction, junction efficiency
not less than 95% and with 38mm X 38mm mesh
opening.

26.15 Supplying & laying of bi-axial extruded high modulus 1.00 Sqm 555.05 One Square 555.00
polypropylene geogrid coforming to MORTH Metre
SPECIFICATION for base/sub-base reinforcement having
minimum tensile strength 40kN/m in the longitudinal
and transverse direction, with 14kN/m and 28kN/m
tensile strength at 2% and 5% strain respectively in the
longitudinal and transverse direction, junction efficiency
not less than 95% and with 38mm X 38mm mesh
opening.

26.16 Supplying & laying of drainage composite for use

behind walls, between two different fills, alongside
drains of road, below concrete lining of canals etc.
Geocomposite for planar drainage, realized by
thermobonding a draining core in extruded
monofilaments with two filtering nonwoven geotextiles
that may also be working as separation or protecting
layers. The draining three dimensional core will have a
“W” configuration as longitudinal parallel channels.

Minimum thickness to be 7.2mm, with two filtering UV 1.00 Sqm 986.95 One Square 987.00
stabilized polypropylene nonwoven geotextile of Metre
minimum thickness of 0.75mm characteristic opening
size (090) of 110 micron and tensile strength of 8.0
KN/m that will be working as separation or protecting
layer, geocomposite having in plane flow capacity of 2.1
L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure
and tensile strength of 18 kN/m , with mass per unit
area of 740 gsm, supplied in the form of roll for easy
transportation to site of work as per detailed
specification all complete as per directions of Engineer
in charge.

DSR - 2023 IN MS EXCEL Page 230 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.17 Supplying & laying of drainage composite for use 1.00 Sqm 1166.95 One Square 1167.00
behind walls, between two different fills, alongside Metre
drains of road, below concrete lining of canals etc.
having thermobonding a draining core - HDPE geonet
comprises of two sets of parallel overlayed ribs
integrally connected to have a rhomboidal shape with a
polyethylene film and a nonwoven geotextile having
mass per unit area 130 gsm and tensile strength of 8.0
kN/m that will be working as separation or protecting
layer, geocomposite having in plane flow capacity of 0.7
L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure
and tensile strength of 13.5 kN/m , with mass per unit
area of 830 gsm, at easily accessible location including
top and bottom, with all leads and lifts, manpower and
machinery, materials, labour etc. complete and as
directed by Engineer - In - Charge.

26.18 Supplying and laying high strength flexible geogrids

(HSFG) as soil reinforcement / basal reinforcement as
per MORTH 3100 and IRC 113, made of high tenacity
polyester core with polyethylene coating with Minimum
Long Term Design Strength (LTDS) of more than 50% of
ultimate tensile strength at 30 degree Celcius
corresponding to 12 % strain .

26.18.1 Ultimate tensile strength- 100 kN/m 1.00 Sqm 393.85 One Square 394.00
Metre
26.18.2 Ultimate tensile strength- 150 kN/m 1.00 Sqm 411.10 One Square 411.00
Metre
26.18.3 Ultimate tensile strength- 200 kN/m 1.00 Sqm 645.80 One Square 646.00
Metre
26.18.4 Ultimate tensile strength- 250 kN/m 1.00 Sqm 663.05 One Square 663.00
Metre
26.18.5 Ultimate tensile strength- 300 kN/m 1.00 Sqm 681.80 One Square 682.00
Metre
26.18.6 Ultimate tensile strength- 350 kN/m 1.00 Sqm 699.05 One Square 699.00
Metre
26.18.7 Ultimate tensile strength- 400 kN/m 1.00 Sqm 843.00 One Square 843.00
Metre
26.18.8 Ultimate tensile strength- 500 kN/m 1.00 Sqm 933.75 One Square 934.00
Metre
26.18.9 Ultimate tensile strength- 600 kN/m 1.00 Sqm 1022.95 One Square 1023.00
Metre
26.18.10 Ultimate tensile strength- 700 kN/m 1.00 Sqm 1202.90 One Square 1203.00
Metre
26.18.11 Ultimate tensile strength- 800 kN/m 1.00 Sqm 1337.50 One Square 1338.00
Metre
26.18.12 Ultimate tensile strength- 900 kN/m 1.00 Sqm 1562.85 One Square 1563.00
Metre
26.18.13 Ultimate tensile strength- 1000 kN/m 1.00 Sqm 1742.80 One Square 1743.00
Metre
26.18.14 Ultimate tensile strength- 1100 kN/m 1.00 Sqm 1833.60 One Square 1834.00
Metre
26.18.15 Ultimate tensile strength- 1200 kN/m 1.00 Sqm 1922.80 One Square 1923.00
Metre

DSR - 2023 IN MS EXCEL Page 231 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.19 Providing at all heights, levels and locations Aluminium
profile industrial troughed sheet of Alloy 31500/ 31000/
40800, conforming to IS 1254, IS 737, IS 2676. The
sheet shall be fixed using self drilling/ self tapping SS
screws of size 5.5x65 mm with EPDM seal complete
upto required pitch in horizontal, vertical or curved
surfaces i/c cutting to size and shape where required as
per specifications, detail drawings and direction of
Engineer -in- Charge. The rate shall be inclusive of all
screws, seal, ridge, labour, scaffolding, machinery for
fixing and approved sealent where required etc. but
excluding the cost of purlins, rafters and trusses.

26.19.1 0.71 mm thick, the profile detail width 1044/920 mm, 1.00 Sqm 1153.95 One Square 1154.00
cover width 1000/875 mm. Metre
26.19.2 0.91 mm thick, the profile detail width 1044/920 mm, 1.00 Sqm 1462.90 One Square 1463.00
cover width 1000/875 mm. Metre
26.22 Providing and fixing false ceiling at all heights with
integral densified calcium silicate reinforced with fibre
and natural filler false ceiling tiles of Size 595x595mm of
approved texture, design and patterns having NRC
(Noise Reduction coefficient) of 0.50 (minimum) as per
IS 8225:1987, Light reflectance of 85% (minimum).

Non combustible as per BS:476 (part-4), fire

performance as per BS:476 (part 6 &7), humidity
resistance of 100%, thermal conductivity < 0.043 W/m K
as per ASTM 518:1991, in true horizontal level
suspended on interlocking metal T-Grid of hot dipped
galvanised iron section of 0.33mm thick (galvanized @
120 grams per sqm including both sides) comprising of
main-T runners of size 24x38 mm of length 3000 mm,
cross - T of size 24x32 mm of length 1200 mm and
secondary intermediate cross-T of size 24x32 mm of
length 600mm to form grid module of size 600 x 600
mm, suspended from ceiling using galvanised mild steel
items (galvanizing @ 80 grams per sqm) i.e. 50 mm
long, 8 mm outer diameter M-6 dash fasteners, 6 mm
dia fully threaded hanger rod upto 1000 mm length and
L-shape level adjuster of size 85x25x25x2 mm.

Galvanised iron perimeter wall angle of size 24x24x0.40

mm of length 3000 mm to be fixed on periphery wall /
partition with the help of plastic rawl plugs at 450 mm
center to center and 40 mm long dry wall S.S screws.
The work shall be carried out as per specifications,
drawing and as per directions of the Engineer-in-
Charge.

26.22.1 With 15 mm thick tegular edged light weight calcium 1.00 Sqm 2207.00 One Square 2207.00
silicate false ceiling tiles. Metre
26.22.2 With 15 mm thick tegular/butt edged without 1.00 Sqm 2301.10 One Square 2301.00
perforation plain/designer light weight calcium silicate Metre
Anti-Microbial Bio-Safe coated false ceiling tiles
Confirming to JIS-Z2801 and ASTM G-21

DSR - 2023 IN MS EXCEL Page 232 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.23 Providing and fixing false ceiling at all heights with
integral densified calcium silicate reinforced with fibre
and natural filler false ceiling tiles of Size 595x595 mm
of approved texture, design and patterns having NRC
(Noise Reduction coefficient) of 0.50 (minimum) as per
IS 8225:1987, Light reflectance of 85% (minimum).

Non combustible as per BS:476 (part-4), fire

performance as per BS:476 (part 6 &7), humidity
resistance of 100%, thermal conductivity < 0.043 W/m K
as per ASTM 518:1991, in true horizontal level
suspended on interlocking metal powder coated T-Grid
of hot dipped galvanised iron section of 0.40 mm thick
on Silhouette profile,rotary stiched double webbed
white with 6mm reveal profile (white/black), comprising
of main-T runners of size 15x42mm of length 3000 mm,
cross - T of size 15x42 mm of length 1200 mm and
secondary intermediate cross- T of size 15x42 mm of
length 600mm to form grid module of size 600 x 600
mm, suspended from ceiling using galvanised mild steel
items (galvanizing @ 80 grams per sqm) i.e. 50 mm
long, 8 mm outer diameter M-6 dash fasteners, 6 mm
dia fully threaded hanger rod upto 1000 mm length and
L-shape level adjuster of size 85x25x2 mm.

Galvanised iron perimeter wall angle of size 22x19x0.40

mm of length 3000 mm to be fixed on periphery wall /
partition with the help of plastic rawl plugs at 450 mm
center to center and 40mm long dry wall S.S screws.
The work shall be carried out as per specifications,
drawing and as per directions of the Engineer-in-
Charge.

26.23.1 With 15 mm thick integral densified micro edge light 1.00 Sqm 2630.40 One Square 2630.00
weight calcium silicate false ceiling tiles Metre
26.24 Providing and fixing in position wall panelling at all
heights with integral densified calcium silicate
panels/tiles of size 595 x 595mm, having NRC (Noise
Reduction coefficient) of 0.50 (minimum) as per IS
8225:1987, Light reflectance of 85% (minimum). Non
combustible as per BS:476 (part-4), fire performance as
per BS:476 (part 6 &7), humidity resistance of 100%,
thermal conductivity <0.043 W/m K as per ASTM
518:1991, comprising of a frame made from especially
fabricated galvanised mild steel sheet 0.50 mm thick
pressed section (galvanizing @120 grams per sqm
including both sides) i.e.vertical studs of size 48 x 34 x
36 mm are placed at 600mm center to center in a floor
and ceiling channel section of size 50 x 32m fixed to the
floor and soffit at 600mm centers using 12mm dia,
50mm long wedge type expanded zinc alloy dash
fastner with 10mm bolt.

DSR - 2023 IN MS EXCEL Page 233 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
This same channel is then to be fixed in horiziontal
direction at 600mm center to center so as to form a
grid of 600mm x 600mm. Glasswool of 50mm thickness
is then to be inserted in the slots and finally calcium
silicate non combustible panels/ tiles are to be screw
fixed with self tapping pan head nickel coated mild steel
screws of size 13 x 3.2mm on to this grid leaving an
even groove of 1 mm between the panels. The joints
between the panels are to be duly jointed and finished
using recommended jointing calcium silicate based
compound and fiber joint tape roll 50mm wide (90
metre) roll and two coats of primer suitable for
panelling as per manufacturer’s specification as per
direction of Engineer-in-Charge all complete.

26.24.1 With 15 mm thick fully perforated square/butt edge 1.00 Sqm 3117.60 One Square 3118.00
light weight calcium silicate panels/ tiles Metre
26.25 Providing and fixing 15 mm thick false ceiling tiles at all 1.00 Sqm 1781.20 One Square 1781.00
heights with integral densified calcium silicate Metre
reinforced with fibre and natural filler false ceiling tiles
of Size 595x595 mm of approved texture, design and
patterns having NRC (Noise Reduction coefficient) of
0.50 (minimum) as per IS 8225:1987, Light reflectance
of 85% (minimum). Non combustible as per BS:476
(part-4), fire performance as per BS:476 (part 6 &7),
humidity resistance of 100%, thermal conductivity <
0.043 W/m K as per ASTM 518:1991,in true horizontal
level on the existing frame work consisting of T-sections
and L - sections suitably fixed according to tile size as
per direction of Engineer-in-charge.

26.26 Providing & fixing false ceiling at all heights with GRG
(Glass Fibre Reinforced Gypsum) false ceiling tiles of
Size 595x595 mm of approved texture, design and
patterns having moisture content less than 2%,
humidity resistance of 99%, NRC0.50 to 0.75 as per IS
8225:1987, Non combustible as per BS 476 (part 4)-
1970 and light reflectance of 85% (minimum) to be laid
in true horizontal level suspended on inter-locking
metal T-Grid of hot dipped galvanised iron section of
0.33mm thick (galvanized @ 120 grams per sqm
including both sides) comprising of main-T runners of
size 15x32 mm of length 3000 mm, cross - T of size
15x32 mm of length 1200 mm and secondary
intermediate cross-T of size 15x32 mm of length
600mm to form grid module of size 600 x 600 mm,
suspended from ceiling using galvanised mild steel
items (galvanizing @ 80 grams per sqm) i.e. 50 mm
long,

8 mm outer diameter M-6 dash fasteners, 6 mm dia

fully threaded hanger rod upto 1000 mm length and L-
shape level adjuster of size 85x25x2 mm. Galvanised
iron perimeter wall angle of size 24x24x0.40 mm of
length 3000 mm to be fixed on periphery wall /
partition with the help of plastic rawl plugs at 450 mm
center to center and 40 mm long dry wall wood screws.
The work shall be carried out as per specifications,
drawing and as per directions of the Engineer-in-
Charge.

DSR - 2023 IN MS EXCEL Page 234 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.26.1 With semi perforated 12 mm thick micro tegular edged 1.00 Sqm 1852.05 One Square 1852.00
GRG false ceiling tiles. Metre
26.26.2 With fully perforated 12 mm thick micro tegular edged 1.00 Sqm 1907.35 One Square 1907.00
or 10 mm thick square edged GRG false ceiling tiles. Metre

26.27 Providing and fixing mineral fibre false ceiling tiles at all
heights of size 595X595mm of approved texture, design
and pattern. The tiles should have Humidity Resistance
(RH) of 99%, Light Reflectance > 85%, Thermal
Conductivity k = 0.052 - 0.057 w/m K, Fire Performance
as per (BS 476 pt - 6 &7)in true horizontal level
suspended on interlocking T-Grid of hot dipped all
round galvanized iron section of 0.33 mm thick
(galvanized @120 gsm) comprising of main T runners of
15x32 mm of length 3000 mm, cross T of size 15x32mm
of length 1200 mm and secondary intermediate cross T
of size 15x32 mm of length 600 mm to form grid
module of size 600x600 mm suspended from ceiling
using galvanized mild steel item (galvanised @ 80 gsm)
50 mm long 8mm outer diameter M-6 dash fasteners, 6
mm diameter fully threaded hanger rod up to 1000 mm
length and L-shape level adjuster of size 85x25x2 mm,

spaced at 1200 mm centre to centre along main ‘T’. The

system should rest on periphery walls /partitions with
the help of GI perimeter wall angle of size 24x24X3000
mm made of 0.40 mm thick sheet, to be fixed to the
wall with help of plastic rawl plug at 450 mm centre to
centre & 40 mm long dry wall S.S. screws. The exposed
bottom portion of all T-sections used in false ceiling
support system shall be pre-painted with polyester
baked paint, for all heights. The work shall be carried
out as per specifications, drawings and as per directions
of the engineer-incharge.

26.27.1 With 16 mm thick beveled tegular mineral fibre false 1.00 Sqm 2333.60 One Square 2334.00
ceiling tile (NRC 0.55 to 0.6) Metre
26.27.2 With 20 mm thick beveled tegular mineral fibre false 1.00 Sqm 2671.20 One Square 2671.00
ceiling tile (NRC 0.7) Metre
26.27.3 With 16 mm thick beveled tegular mineral fibre 1.00 Sqm 2447.15 One Square 2447.00
Antimicrobial false ceiling tile confirming to ISO 5 (class Metre
100) specifications
26.28 Chipping of unsound/weak concrete material from
slabs, beams, columns etc. with manual Chisel and/ or
by standard power driven percussion type or of
approved make including tapering of all edges, making
square shoulders of cavities including cleaning the
exposed concrete surface and reinforcement with wire
brushes etc. and disposal of debris for all lead and lifts
all complete as per direction of Engineer-In-Charge

26.28.1 75 mm average thickness 1.00 Sqm 378.00 One Square 378.00

Metre
26.28.2 50 mm average thickness 1.00 Sqm 256.35 One Square 256.00
Metre
26.28.3 25 mm average thickness 1.00 Sqm 126.75 One Square 127.00
Metre

DSR - 2023 IN MS EXCEL Page 235 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.29 Cleaning of reinforcement from rust from the
reinforcing bars to give it a total rust free steel surface
by using alkaline chemical rust remover of approved
make with paint brush and removing loose particles
after 24 hours of its application with wire brush and
thoroughly washing with water and allowing it to dry,
all complete as per direction of Engineer-In-Charge.

26.29.1 Bars upto 12 mm diameter 1.00 m 8.25 One Metre 8.00

26.29.2 Bars above 12 mm diameter 1.00 m 16.45 One Metre 16.00
26.30 Drilling suitable holes in reinforced or plain cement
concrete with power driven drill machine to a minimum
depth of 100mm upto 200mm in RCC beams, lintels,
columns and slabs to introduce steel bars for
sunshades/balconies including fixing the steel bars in
position using epoxy resin anchor grout of approved
make but excluding the cost of reinforcement, all
complete as per direction of Engineer-In-Charge.

26.30.1 Upto and including 12mm dia. 1.00 No. 141.20 Each 141.00
26.31 Providing, mixing and applying bonding coat of
approved adhesive on chipped portion of RCC as per
specifications and direction of Engineer-In-charge
complete in all respect.

26.31.1 SBR Polymer (@10% of cement weight) modified 1.00 Sqm 141.20 One Square 141.00
cementitious bond coat @ 2.2 kg cement per sqm of Metre
surface area mixed with specified proportion of
approved polymer

26.31.2 Epoxy bonding adhesive having coverage 2.20 sqm/kg 1.00 Sqm 285.20 One Square 285.00
of approved make. Metre
26.32 Providing, mixing and applying SBR polymer (of
approved make) modified Cement mortar in proportion
of 1:4 (1 cement: 4 graded coarse sand with polymer
minimum 2% by wt. of cement used) as per
specifications and directions of Engineer-in-charge.

Note: Measurement and payment: The pre-

measurement of thickness shall be done just after the
surface preparation is completed and Payment under
this item shall be made only after proper wet curing has
been done and surface has been satisfactorily
evaluated by sounding / tapping with a blunt metal
instrument and/or the 75mm size cube crushing
strength at the end of 28 days to be not less than 30
N/Sqmm2).

26.32.1 12 mm average thickness. 1.00 Sqm 388.65 One Square 389.00

Metre
26.32.2 25 mm average thickness in 2 layers. 1.00 Sqm 587.35 One Square 587.00
Metre
26.32.3 50 mm average thickness in 3 layers. 1.00 Sqm 1174.70 One Square 1175.00
Metre
26.33 Providing, mixing and applying SBR polymer (of
approved make @ minimum 2% by wt. of cement used)
modified plain/reinforced cement concrete for
structural members having minimum characteristic
compressive strength [with ordinary portland cement,
coarse sand and graded stone aggregate of 10mm
maximum size in proportion as per design criteria] with
specified average thickness.

DSR - 2023 IN MS EXCEL Page 236 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
Note: Rates shall be for finished surface area of
concrete and shall include the cost of labour, concrete
and appropriate approved Super- Plasticiser for
rendering concrete as flowable and SBR polymer but
shall exclude cost of reinforcement, bond coat, Shear
Keys, centering and shuttering, strutting, propping etc.

(Payment under this item shall be made only after

proper wet curing has been done and surface has been
satisfactorily evaluated by sounding/ tapping with a
blunt metal instrument)

26.33.1 50mm thick in Grade M 25 with cement content not 1.00 Sqm 569.15 One Square 569.00
less than 330 kg per cum Metre
26.33.2 75mm thick in Grade M 25 with cement content not 1.00 Sqm 853.70 One Square 854.00
less than 330 kg per cum Metre
26.34 Providing and laying SBR Polymer modified (of
approved make @ minimum 2% by wt. of cement used)
plain/ reinforced concrete jacket for the structural
members e.g. columns, pillars, piers, beams etc with
concrete having the specified minimum characteristic
compressive strength [with ordinary portland cement,
coarse sand and graded stone aggregate of 10mm
maximum size in proportion as per design criteria] with
specified average thickness all-round existing core of
RCC member.

Note: Rates shall be for finished surface area of

concrete and shall include the cost of making holes in
existing RCC slab, if required, for pouring concrete in
shuttering mould of jacket and appropriate approved
Super-Plasticiser for rendering concrete as flowable self
compacting and SBR polymer but shall exclude cost of
reinforcement, bond coat, Shear Keys, centering and
shuttering, strutting, propping etc.

(Payment under this item shall be made only after

proper wet curing has been done and surface has been
satisfactorily evaluated by sounding/tapping with a
blunt metal instrument)

26.34.1 50mm thick in Grade M 25 with cement content not 1.00 Sqm 569.15 One Square 569.00
less than 330 kg per cum Metre
26.34.2 75mm thick in Grade M 25 with cement content not 1.00 Sqm 853.70 One Square 854.00
less than 330 kg per cum Metre
26.34.3 100mm thick in Grade M 25 with cement content not 1.00 Sqm 1138.25 One Square 1138.00
less than 330 kg per cum Metre
26.35 Providing and injecting approved grout in proportion
recommended by the manufacturer into cracks/honey-
comb area of concrete/ masonry by suitable gun/pump
at required pressure including cutting of nipples after
curing etc. complete as per directions of Engineer-in-
Charge. (The payment shall be made on the basis of
actual weight of approved grout injected.)

26.35.1 Stirrer mixed Acrylic Polymer of approved make @ 2% 1.00 Kg 119.30 One Kilogram 119.00
of weight of cement used) modified Cement slurry
made with non shrink compound in concrete/RCC work

DSR - 2023 IN MS EXCEL Page 237 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.35.2 Stirrer mixed SBR Polymer (of approved make) modified 1.00 Kg 124.00 One Kilogram 124.00
Cement slurry made with Shrinkage Compensating
Cement in concrete/RCC work.
26.35.3 Epoxy injection grout in concrete/RCC work of approved 1.00 Kg 553.40 One Kilogram 553.00
make
26.36 Providing, erecting, maintaining and removing
temporary protective screens made out of specified
fabric with all necessary fixing arrangement to ensure
that it remains in position for the work duration as
required by the Engineer-in-charge.

26.36.1 Wooven PVC cloth 1.00 Sqm 54.25 One Square 54.00
Metre
26.37 Cleaning of exposed concrete surface of sticking 1.00 Sqm 382.40 One Square 382.00
material including loose and foreign material by sand Metre
blasting with coarse sand followed by and including
cleaning with oil free air blast as per direction of
Engineer in charge.

26.38 Shotcreting R.C.C. columns, beams and slabs etc. in

layers with approved design mix concrete having the
specified minimum characteristic compressive strength
[with ordinary portland cement, coarse sand and
graded stone aggregate of 10 mm maximum size in
proportion as per design criteria] including the cost of
centering and shuttering at edges and corners etc. as
directed by Engineerin- Charge Note: Rates shall include
the providing necessary ground wires etc. The levelling
gauges, if used, shall be paid for separately. Payment
under this item shall be made only after proper wet
curing has been done and surface has been
satisfactorily evaluated by sounding/ tapping with a
blunt metal instrument.

26.38.1 25mm thick in Grade M 25 with cement content not 1.00 Sqm 746.90 One Square 747.00
less than 330 kg per cum Metre
26.38.2 50mm thick in Grade M 25 with cement content not 1.00 Sqm 1151.05 One Square 1151.00
less than 330 kg per cum Metre
26.38.3 75mm thick in Grade M 25 with cement content not 1.00 Sqm 1628.85 One Square 1629.00
less than 330 kg per cum Metre
26.39 Providing and inserting 12mm dia galvanised steel 1.00 No. 236.90 Each 237.00
injection nipple in honey comb area and along crack line
including drilling of holes of required diametre (20mm
to 30mm) up to depth from 30mm to 80mm at required
spacing and making the hole & crack dust free by
blowing compressed air, sealing the distance between
injection nipple with adhesive chemical of approved
make and allow it to cure complete as per direction of
Engineer-In-Charge.

26.40 Providing and fixing hard drawn steel wire fabric of size 1.00 Sqm 902.55 One Square 903.00
75 x25 mm mesh or other suitable size wire mesh to be Metre
fixed & firmly anchored to the concrete surface by
means of "L" shaped mild steel shear key welded with
existing reinforcement including the cost of materials,
labour, tool & plants as approved by Engineer-in-
charge.

DSR - 2023 IN MS EXCEL Page 238 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.41 Designing, providing, installing and fixing factory
finished custom designed cold form Light Gauge Steel
Framed super structure comprising of steel wall panel,
trusses, purlins etc manufactured out of minimum 0.75
mm thick steel sheet as per design requirements. The
steel sheet shall be galvanized (AZ-150gms Aluminium
Zinc Alloy coated steel having minimum yield strength
300-550 Mpa) conforming to AISI specifications and IBC
2009 for cold formed steel framing and construction
and also as per IS: 875-1987, ISO 800-1984 and IS:801-
1975. The wind load shall be as per provisions of IS 875
(part -III). LGSFS frame shall be designed as per IS: 801
using commercially available software such as Frame
CAD Pro-11.7/ STAAD PRO-V8i/ ArchitekV2.5.16/ Revit
architecture-2011 or equivalent. Proper usage of
Connection Accessories like Heavy Duty Tension Ties,
Light Duty Hold-ons, Twist Straps (to connect truss with
wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing
Sections, L-Shaped Angles for better structural stability.

The framing section shall be cold form C-type having

minimum web depth 89 mm x 39mm flange x 11mm lip
in required length as per structural design requirement
duly punched with dimple/slot at required locations as
per approved drawings. The slots will be along centre
line of webs and shall be spaced minimum 250mm
away from both ends of the member. The frame can be
supplied in panelized or knock down condition in
specific dimensions and fastened with screws extending
through the steel beyond by minimum of three exposed
threads. All self drilling tapping screws for joining the
members shall have a Type II coating in accordance
with ASTM B633(13) or equivalent corrosion protection
of gauge 10 & 12, TPI 16 & 8 of length 20mm.

The frames shall be fixed to RCC slab or Tie beam over

Neoprene rubber using self expanding carbon steel
anchor bolt of dia as per approved drawings. design
subject to minimum 12mm diameter and 121mm
length conforming to AISI 304 and 316 at 500mm c/c
with minimum embedment of 100mm in RCC (RCC to
be paid separately) and located not more than 300mm
from corners or termination of bottom tracks complete
in all respects.

The item also includes the submission of stability 1.00 Kg 285.90 One Kilogram 286.00
reports duly examined and issued by any NIT/IIT. The
rate includes the concept design, detailed design,
fabrication of sections, transportation, installation and
all required fixing arrangement at site as described
above.

DSR - 2023 IN MS EXCEL Page 239 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.42 Providing and fixing of external wall system on Light
gauge steel frame work with outer face cement boards
as per standard sizes fixed with self- drilling / taping
screws / fasteners @ 60cm c/c of approved make. A
groove of 2 mm to 3mm shall be maintained and
grooves shall be sealed with silicon based sealant. The
board shall be fixed in a staggered pattern. Screws shall
be of counter sunk rib head of 1.60mm to 4 mm thick or
8 to 10 gauge of length varying from 25 to 45 mm and.
Internal face 12.5 mm thick gypsum plaster board fixed
on cement board as per standard sizes fixed with
selfdrilling / taping screws / fasteners @ 60cm c/c of
approved make, proper taping and jointing to be done
using fiber mesh tape and epoxy and acrylic based
jointing compound for seamless finish. (cost of frame
work to be paid for separately)

26.42.1 Outer face- Outer face having 6mm thick fiber cement 1.00 Sqm 3580.65 One Square 3581.00
board Type A, Category-IV as per IS:14862:2000 fixed Metre
on 9mm thick fiber cement board, Type A, Category-IV
as per IS:14862:2000 (high pressure steam cured) Inner
Face-12.5 mm thick gypsum plaster board conforming
to IS 2095:2011 fixed on 8 mm thick fibre cement board
of Type B, Category-Ill conforming to IS:14862:2000
(High pressure steam cured)

26.42.1A Outer face- Outer face having 6mm thick fiber cement 1.00 Sqm 2821.65 One Square 2822.00
board Type A, Category-III as per IS:14862:2000 fixed on Metre
9mm thick fiber cement board, Type A, Category-IV as
per IS:14862:2000 (high pressure steam cured) Inner
Face-12.5 mm thick gypsum plaster board conforming
to IS 2095:2011 fixed on 8 mm thick fibre cement board
of Type B, Category-Ill conforming to IS:14862:2000
(High pressure steam cured)

26.42.2 Outer face: Outer face having 8 mm thick cement 1.00 Sqm 3167.85 One Square 3168.00
bonded particle Board fixed on 10 mm thick cement Metre
bonded particle board. (Termite, Fire and Moisture
Resistance) as per IS 14276:1995. Inner face:-12.5 mm
thick gypsum plaster board conforming to IS 2095:2011
fixed on 8 mm thick cement bonded particle board
(Termite, fire and moisture resistance) confirming to
IS:14276:1995)

26.43 Providing and fixing internal wall panels on Light gauge

steel frame work with 12.5mm thick gypsum plaster
board conforming IS 2095:2011 fixed on cement board
as per standard sizes fixed with self-drilling / taping
screws / fasteners @ 60cm c/c of approved make, self-
drilling / taping screws / fasteners @ 60cm c/c of
approved make, or 8 to 10 gauge of length varying from
25 to 45 mm. Proper taping and jointing to be done
using fiber mesh tape and epoxy and acrylic based
jointing compound for seamless finish. (cost of frame
work to be paid for separately

26.43.1 Cement Fiber Board 8 mm thick of Type B, Category III 1.00 Sqm 2221.05 One Square 2221.00
as per IS 14862:2000 (High pressure Steam Cured) Metre
26.43.2 Cement Bonded particle board 8 mm (Termite, Fire & 1.00 Sqm 2189.75 One Square 2190.00
Moisture Resistance), as per IS:14276 : 1995 Metre

DSR - 2023 IN MS EXCEL Page 240 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.44 Providing and fixing in all exterior face panels 1.00 Sqm 298.75 One Square 299.00
breathable vapour barrier underneath the cement fiber Metre
board as per National Building Code 2009 complete as
per direction of Engineer-in-charge.

26.45 Supplying and installation of moisture resistant/fire

resistant cement board as per standard sizes fixed with
self-drilling / taping screws. Screws shall be of counter
sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge
of length varying from 25 to 45 mm.

26.45.1 Cement Fiber Board 6 mm thick as per IS 14862:2000 of 1.00 Sqm 1430.15 One Square 1430.00
type B (High pressure Steam Cured) Metre
26.45.2 Cement Bonded particle board 8 mm thick (Termite, 1.00 Sqm 991.95 One Square 992.00
Fire & Moisture Resistance), as per IS:14276 : 1995 Metre
26.46 Providing and fixing in position 200 mm thick factory
made expanded polystyrene core (EPS) wall panels
consisting of EPS core sandwitched between two
Engineered sheets of welded wire fabric mesh duly
finished with shortcrete materials on outer faces. The
fabric mesh shall be made of 3 mm dia G.I. wire mesh
with 50 mm pitch in both the directions and on both
faces of the wall, kept at 120-135 mm gap and
connected by the zig zag G.I. wire of 3 mm dia at
alternate row by welding (at an angle ranging from 50 -
60 degree).

The EPS core shall consists of 100 mm thick EPS of 1.00 Sqm 4347.15 One Square 4347.00
density not less than 20 kg/ per cum. Both the outer of Metre
the panel shall be finished with applying the layer of 50
mm thick cement mortar 1:3 [1 Cement: 3 coarse sand
(not having more than 40% stone schips of size upto 6
mm)]with the help of shortcreting / guniting etc at a
pressure not less than 1 bar (100Kn/sqm) and both
surface finished with trowel. The fixing operations of
wall panels shall be completed in all respect as per
drawings and specifications and under the overall
direction of Engineer-in-charge.

26.47 Providing and fixing in position, 230mm thick factory 1.00 Sqm 4701.60 One Square 4702.00
made Expanded Polystyrene Core (EPS Core) roof/floor Metre
panels made of 3 mm dia G.I. wire mesh with 50 mm
pitch in both the directions and on both faces of panel,
kept at 120-135 mm gap and connected by the zig zag
G.I. wire of 3 mm dia at alternate row by welding (at an
angle ranging from 50-70 degree). The EPS core shall
consist of 100 mm thick EPS of density not less than
20kg/ per cum. The bottom side of the panel shall be
finished by applying a layer of 60-65 mm thick cement
mortar 1: 3 {1 cement: 3 coarse sand (not having more
than 40% stone chips of size upto 6 mm)} À with the
help of shotcreting equipment etc at a pressure of not
less than 1 bar (100Kn/m2) and surface finished with
trowel. The top face of the panel shall be provided and
finished by applying 70-75 mm thick layer of cement
concrete 1:1.5: 3 (1 cement :1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size). Fixing operations
of roof/floor panels shall be completed in all respect as
per drawings and specifications and under the overall
direction of the Engineer-in-charge.

DSR - 2023 IN MS EXCEL Page 241 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.48 Providing and fixing of customized Aluminum Form
work for monolithic construction on RCC members with
repetitive usage made up of aluminium sheets/plates of
minimum 4 mm thickness and grade 6061 (Type-6). The
formwork comprises of (a) wall panel rocker, kicker and
internal soffit corner, external soffit corner, external
corner, internal corner etc. (b) beam components i.e.
beam side panel, prop head for soffit beam, beam soffit
panel, beam soffit bulkhead and (c) deck components
i.e. deck panel, deck prop, prop length, deck mid, soffit
length, deck beam bar. The panels are held in position
by a simple pin and wedge system that passes through
holes in the outside rib of each panel. The tolerance of
the finished panel sha not be less than (-1 mm) and
shall confirm to IS 14987 -1999.Pins and wedges to be
made of high grade hot dipped galvanised mild steel.
This form work also comprises of MS angle Iron, 'Z'
shaped brackets braced diagonally at 0.90 t0 1.00
metre centre to centre on external wall face just the
level

below on which to lay MS square tube panels (Challis) 1.00 Sqm 451.35 One Square 451.00
and guard railing supports to form working platform Metre
and 40 mm dia GI/MS telescopic adjustable props to
support dech formwork and nbeam soffit panels,
including de-shuttering the formwork from odd / even
level to be shifted / lifted to next alternate odd/even
level before which the points and shuttering surface
thoroughly cleaned, pins greaing and shuttering surface
oiling properly before fixing all complete including
sealing of gap between kicker plate and wall panel and
floors (if any) as per design of formwork as provided by
shuttering supplier and as per direction of the Engineer-
in-Charge including filling and finishing the holes of
varied sizes and shapes (left by Keys/Pins of aluminum
formwork while de-shuttering) with GP-2 cementitious
polymer compound mixed with water in ration
prescribed by the manufacturer to form consistent
workable enough by in the holes upto full depth of wall
using appropriate tools and finishing smooth all
complete as per direction of Engineer-in-Charge.

DSR - 2023 IN MS EXCEL Page 242 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.49 Providing and fixing in position factory made EPS
cement sandwich wall/ roof/ floor light weight solid
core panels made of core material of EPS granule
balls/beads (conforming to IS 4671:1984 and shall have
density not less than 15kg per cum) adhesive, cement,
sand, flyash and other bonding material in mortar state
processed to form in a preset mould. The outer face on
both sides of the panels will be non asbestos fiber
cement board confirming to IS 14862:2000 or Calcium
silicate board confirming to EN 14306:2009 of 5mm
thick each. Panel shall be laid on 6mm thick cement
mortar (1 cement: 2 fine sand) mixed with chemical
adhesive of 0.5kg per 50kg of cement or shall be
preferably fixed into 'C' channel made of 1.2mm thick
MS plate screwed/fastenened to the slab/column/beam
etc. The panel shall fixed vertically with tongue and
groove joint and horizontally locked with steel bar
between each other and floors and filled with cement
mortar and adhesive. Panels should be used as floor &
roofing with additional structural support, steel or RCC
depending upon the design.

All the operation shall be completed in all respect as per

drawings, Manufacturers specifications and under the
overall direction of Engineer-in-Charge (Cost of all the
material is included except "C channel" which will be
paid seperately).

26.49.1 Non load bearing panels 50mm thick of required size 1.00 Sqm 1315.70 One Square 1316.00
Metre
26.49.2 Non load bearing panels 60mm thick of required size 1.00 Sqm 1487.50 One Square 1488.00
Metre
26.49.3 Non load bearing panels 75mm thick of required size 1.00 Sqm 1840.05 One Square 1840.00
Metre
26.49.4 Non load bearing panels 90mm thick of required size 1.00 Sqm 2141.80 One Square 2142.00
Metre
26.49.5 Non load bearing panels 100mm thick of required size 1.00 Sqm 2518.20 One Square 2518.00
Metre
26.50 Providing and fixing in position factory made non
asbestos fibre reinforced aerated cement sandwich
wall/roof/floor light weight solid core panels made of
light weight cement concrete core composed of OPC
cement, pulverized flyash, quick lime, cotton pulp &
Gypsum in mortar state mixed with aeration agent in a
preset mould. The outer face on both sides of the
panels will be non-asbestos fibre cement board
confirming to IS: 14862:2000. These solid wall panels
are installed using Galvanized iron steel tracks/C
channel of 1 mm thick of required sizes as
recommended by manufacturer's and fixed to floor and
RCC soffit in plumb to each other with steel
screw/fasteners.

DSR - 2023 IN MS EXCEL Page 243 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
The panel shall be fixed vertically with tongue & groove
joint with cement-based polymer modified jointing
compound. The exposed surface finished with fibre
mesh/glass fibre tape with polymer based jointing
compound having superior flexibility. Panels should be
used as floor & roofing with additional structural
support, steel or RCC depending upon the design. All
the operation shall be completed in all respect as per
drawings, Manufacturers specifications and under the
overall direction of Engineer-in-Charge (Cost of all the
material is included except "tracks/ C channel" which
will be paid separately).

26.50.1 Non load bearing panels 50 mm thick of required size 1.00 Sqm 1527.50 One Square 1528.00
(minimum 4 mm thick fibre cement board, Type B, Metre
category III as per IS : 14862 - 2000 on both faces.
26.50.1A Non load bearing panels 50 mm thick of required size 1.00 Sqm 1635.05 One Square 1635.00
(minimum 4 mm thick fibre cement board, Type A, Metre
category III as per IS : 14862 - 2000 on both faces.
26.50.1B Non load bearing panels 50 mm thick of required size 1.00 Sqm 2068.25 One Square 2068.00
(minimum 4 mm thick fibre cement board, Type A, Metre
category IV as per IS : 14862 - 2000 on both faces.
26.50.2 Non load bearing panels 75 mm thick of required size 1.00 Sqm 1841.20 One Square 1841.00
(minimum 4 mm thick fibre cement board, Type B, Metre
category III as per IS : 14862 - 2000 on both faces.
26.50.2A Non load bearing panels 75 mm thick of required size 1.00 Sqm 1784.40 One Square 1784.00
(minimum 4 mm thick fibre cement board, Type A, Metre
category III as per IS : 14862 - 2000 on both faces.
26.50.2B Non load bearing panels 75 mm thick of required size 1.00 Sqm 2326.65 One Square 2327.00
(minimum 4 mm thick fibre cement board, Type A, Metre
category IV as per IS : 14862 - 2000 on both faces.
26.51 Supplying of standard quality GFRG panel of 124 mm 1.00 Sqm 1477.30 One Square 1477.00
thickness with modular cavities purchased from GFRG Metre
panel manufacturing plant in the length and height,
including cutting of door, window and ventilator
opening as per the cutting drawing prepared by
architects /design engineers for the construction of
GFRG building and loaded in stillages for transportation
to the construction site. Cost of panel includes security
deposits, hire charges of stillages & jaws, cost of
transportation in trucks/ lorries without any damages
upto 300 km including all leads and lifts from GFRG
manufacturing plant to construction site and unloading
at site using suitable fork lift/ crane. (Payment shall be
made on the basis of area of one side of panel without
reduction of opening of door/ window / Ventilators).
For transportation above 300 Km additional charges to
be paid.

DSR - 2023 IN MS EXCEL Page 244 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.52 Erection of CFRG panels in walls in all floors using
suitable crane per instructions of Engineer-in-Charge, as
per cutting drawings and structural drawings, in perfect
line and plumb, above RCC plinth beam/ GFRG panel
below and provide necessary lateral/ slanting support
to keep the wall panel in safe position, providing &
tieing of Reinforcement as per structural drawings and
applying a coat of water repellant coating Zycosil/
equivalent or equivalent product (1 Zycosil/equivalent
compound : 10 water) to saturation level over RCC
plinth beam to provide water proofing treatment to
joint between wall panel and plinth beam as per guide
lines / instruction by the engineer in charge. (Cost of
reinforcement, water proofing of walls and plinth
beam / GFRG panel below joints and installation of door
/ window frames before filling of concrete shall be paid
for separately).

The rate quoted shall include making provision for

laying of lintels, beams, sunshades, staircase beams,
lofts, plumbing work, electrical conduits and any
structural insertion etc., as per the drawing and
direction of the engineer in charge. The payment shall
be made based on actual exposed area (on one side
only) of the panel.

The work shall be carried out as per the Special 1.00 Sqm 283.25 One Square 283.00
Conditions for Glass Fibre Reinforced Gypsum (GFRG) Metre
structures mentioned in NIT.Note: i) When cutting
panel, ‘A’ side is to be for outside or external surface of
respective external wall and B side is to be for internal
surface of wall. ii) Erection of panel is to be with
reference to both building plan and cutting drawing by
following notational mark indicated in the cutting
drawing as well as notional mark written on each panel
cut as per cutting drawing.

26.53 Filling empty cavities (as shown in the structural

drawing design) with quarry dust mixed with 5% of
cement (by volume) after initial infill of 50 mm thick
M25 Concrete at base bottom of cavities to seal off,
infill wall panel cavities in 3 stages as detailed below,

(i) First pour infill limited to 0.3 to 0.5 mm height from

bottom of the panel.
(ii) Second pour infill shall be done only after 90
minutes interval between successive pours. The
maxmum height of infill shall be restricted to to 1.5 m
height or up to the top level of door / window.

(iii) Third pour infill. After an interval of 90 minutes of

second pour infill or pour the balance height up to the
bottom of embedded RCC tie beam. Pour enough water
just required to dampen the dry mix enough to form
cake form after each stage.

(Cost of laying M25 Concrete shall be paid for

seperately)

DSR - 2023 IN MS EXCEL Page 245 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
(If any rain falls in between any stages of concrete pour, 1.00 Cum 2604.30 One Cubic 2604.00
make sure to cover the panel top to prevent ingress of Metre
water or water falling into the cavities. In case of water
collection over the concrete inside the panel, drill 10
mm hole in GFRG panel immediately above concrete
filled level to drain out water before pour / infill of
balance concreting).

26.54 Laying GFRG Panel as Roof / Floor slab panel and stair
case panel using suitable crane as per instructions of
Engineer-in-Charge, including providing support system
with 25 mm x 300 mm -400 mm wide plywood, as
runner with proper prop below proposed micro beams
including

(a) Cutting of top flange of panel to 180 mm wide

(leaving a 25 mm projection on either side) to provide
RCC embedded micro beam as per cutting drawings and
structural drawings.

(b) Reinforcement of micro beams and tie beams to be

provided in position with proper anchorage as per
structural drawings.
(c) Provision of Electrical cabling, fan hooks and laying
of pipes for plumbing work
(d) Concreting of Tie beam, micro beam and top of 1.00 Sqm 287.40 One Square 287.00
GFRG panels (50 mm thick) with M25 Cement Concrete Metre
Mix using concrete aggregate of size less than 20 mm
including laying of 10 gauge 100x100 mm size weld
mesh

26.55 Supplying and Fixing gauge weld mesh of size 100 mm x 1.00 Sqm 254.75 One Square 255.00
100 mm for floor roof slab concrete screed over the Metre
micro beams as reinforcements. The weld mesh shall be
fixed as per drawings.

26.56 Application of ZMB 60 / equivalent solution (100 kg 1.00 Sqm 371.25 One Square 371.00
ZMB 60 / equivalent solution, 1 Litre ZMB nano Thinner, Metre
20 litre water and 1 Litre Zycoprime / equivalent = 122
litre/Kg) over already applied coat of Zycosil /
equivalent and Zycoprime / equivalent solution on the
top of all the RCC plinth beams by brush/spray coat
before erection of GFRG over RCC plinth beams in GF. In
the case of upper floors 150 mm wide on floor slab for
all external walls, bath/ toilet/ wet areas (3 hours drying
time) before erection of wall panel on upper floors
including erection of parapet walls.

26.57 After erection of GFRG wall panels, seal all GFRG wall 1.00 m 92.45 One Metre 92.00
joints with paper tape temporarily. Wtaer proofing
treatment of vertical joints with Zycosil / equivalent
water proofing solutions [1 Litre of Zycosil / equivalent
& 20 Litres of water stirred first & 2 litre of Zycoprime /
equivalent added and stirred (total 23 litres)] with 50 ml
syringe till the gap and filled concrete is completely
saturated. After removing the paper seal, seal off the
vertical joints with water proofing material "Grout RW /
Equivalent" (sealing cost excluded).

DSR - 2023 IN MS EXCEL Page 246 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.58 Filling of joints between RCC plinth beam / floor slab 1.00 m 49.30 One Metre 49.00
and wall apnel of external wall, toilet / bath room / wet
areas wall on all floor and parapet wall over roof slab,
stair case head room at the time of erection of GFRG
panels with grout RW / equivalent sealant compound
after the erection of panel before the infill of concrete
in panel cavities and fine finish. This applies to for all
horizontal and vertical joints between GFRG wall and
slab panels.

26.59 Water proofing of vertical joints (of external side and 1.00 m 49.95 One Metre 50.00
internal side) between door frame, window & ventilator
frame (on all four sides) of outer wall over the Zycosil /
equivalent & Zycoprime / equivalent solution already
applied (before the intallation of door / window /
ventilator frame in position) and finished with Grout
RW / equivalent.

26.60 Water proofing treatment of RCC sunshade with 1.00 Sqm 136.45 One Square 136.00
Zycosil / equivalent water proffing solution [1 Litre Metre
Zycosil / equivalent & 20 litres of water stirred first & 2
litres of Zycoprime / equivalent added and stirred (total
23 litres)] till it meats the saturation level and testing as
per RIELM or by water drops test in which water drop
do not absorb but drop remains or rolls.

26.61 In-filling / sealing the joints between RCC lintel cum 1.00 m 49.95 One Metre 50.00
sunshade and wall (on all external side) in all floors by
pushing in Grout RW / equivalent in paste form and
coving 20 mm x 20 mm after applying a coat of Zycosil /
equivalent & Zycoprime / equivalent solution before
cement plastering of top, bottom and sides of RCC
sunshade.

26.62 Designing, providing, installing and fixing factory 1.00 Kg 182.05 One Kilogram 182.00
finished custom designed pregalvanised high tensile
steel joists manufactured from G350 Z275 confirming to
IS: 277-1992, minimum coating of galess 35 Mpa &
minimum tensile strength of 380 Mpa placed 1.23
metre apart to support the load of slab etc as per the
design and direction of Engineer-in-Charge.

26.63 Providing and fixing special adjustable lockbars of mild 1.00 Kg 27.10 One Kilogram 27.00
steel E-250 to support the temporary plywood for work
between joists during construction as per design &
directions of the Engineer-in-charge

26.64 Centering and shuttering with 12 mm thick shuttering of

plywood confirming to IS 4990:2011 and removal of
form at all heights. Plywood will be supported on lock
bars.

26.64.1 Suspended floors, roofs, landings, balconies and access 1.00 Sqm 106.80 One Square 107.00
platform Metre
26.65 Providing and fixing roofing consists of 0.80 mm thick 1.00 Sqm 1525.60 One Square 1526.00
galvanised steel deck sheet confirming to IS: 277-1992 Metre
used as permanent shuttering over which MS wire
mesh 3 mm laid at 100x100 mm grid including edge
trim covered with concrete. This metal deck will be
supported on structuralsteel beam with shear studs.
(Structural steel like Beam, column, joists

DSR - 2023 IN MS EXCEL Page 247 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.66 Providing and fixing in position, 130 mm thick factory
made Expanded Polystyrine Core (EPS) wall panels
consisting of EPS core sandwiched between two
Engineered sheets of welded wire fabric mesh duly
finished with shortcrete materials on outer faces. The
fabric mesh shall be made of 3 mm dia zinc coated G.I.
wire mesh with 50 mm pitch in both the directions and
on both faces of the wall and connected by GI wire of 3
mm dia at alternate row by welding. The EPS core shall
consist of 60 mm thick EPS of density not less than 16
kg/ cum.

Both the outer faces of the panel shall be finished by 1.00 Sqm 2673.70 One Square 2674.00
applying the layer of 35 mm thick cement mortar 1:3 [1 Metre
Cement : 3 Coarse Sand (not having more than 40%
stone chips of sizes upto 6 mm)] with the help of
shortcreting / guniting equipment etc at a pressure not
less than 1 bar (100 MN/sqm) and both surfaces
finished with trowel. Fixing operations of wall panels
shall be completed in all respect as per drawings and
spoecifications and under the overall direction of the
Engineer-in-charge.

26.67 Providing & Fixing External Therma Insulation and

composit system of first layer of self extinguishing type
Expended Polystyrene (EPS) insulation board of 120 mm
thick (max 1 m x 0.5 m section) confirming to IS
4671:1984, having thermal conductivity of 0.034 W/mK,
(measured as per IS 3346 - 1980) density of 20 24 kg
/cum measured as per IS 5688 - 1982, Fire retardant
property self-extinguishing type as per EN 13501-1,
bonded with special polymer modified cementious
adhesive confirming to EOTA ETAG 004 (European
Technical Approval) formulated to bond polystyrene
insulation boards to typical mineral substrate
(according ETAG 004) and polypropylene mechanical
fasteners with plastic pin confirming to EOTA ETAG 014
(European Technical Approval) having dia 10 mm and
length 200 mm on finished level wall and the junction
between two adjacent EPS boards to be sealed with low
expansion moisture cure Polyurethane Foam.

Second layer consists of Fiberglass mesh covered with 1.00 Sqm 3935.35 One Square 3935.00
alkali resistant coating, mass per unit area more than Metre
145 g / sqm mesh size 3.9 x 4.0 mm +/- 10 mm
embedded in special polymer modified cementious
base coat with hydrophobes and the corners will be
protected with corner beads with alkali-resistant mesh
wings atleast 10 cm wide mesh mass per unit area min
145 g/sqm. The surface will be levelled, finished, made
smooth complete in all respect as per manufaturers
specifications and as per direction of Engineer-in-
Charge.

26.68 Providing and laying factory made Precast concrete

solid blocks of 200 mm thickness of grade M10 made of
C&D waste from approvedmanufacturer in foundation
and plinth in:

26.68.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 7387.25 One Cubic 7387.00
Metre

DSR - 2023 IN MS EXCEL Page 248 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.69 Providing and laying factory made Precast concrete
solid blocks of 200 mm thickness of grade M10 made of
C&D waste from approved manufacturer in
superstructure above plinth level up to floor V level

26.69.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 9844.65 One Cubic 9845.00
Metre
26.70 Providing and laying half block masonry with factory
made Precast concrete solid blocks of 100 mm
thickness of grade M10 made of C&D waste from
approved manufacturer in foundation and plinth in:

26.70.1 Cement mortar 1:6 (1 cement : 4 coarse sand) 1.00 Sqm 897.15 One Square 897.00
Metre
26.71 Providing and laying half block masonry with factory
made Precast concrete solid blocks of 100 mm
thickness of grade M10 made of C&D waste from
approved manufacture in rsuperstructure above plinth
level up to floor V level:

26.71.1 Cement mortar 1:6 (1 cement : 4 coarse sand) 1.00 Sqm 1099.15 One Square 1099.00
Metre
26.72 Providing and laying 60mm thick factory made cement 1.00 Sqm 829.75 One Square 830.00
concrete paver block of approved shape and colour of Metre
M -30 grade made of C&D waste by block making
machine with vibratory compaction laid in required
pattern and including over 50mm thick compacted bed
of coarse sand, filling the joints with fine sand etc. all
complete as per the direction of Engineer-in-charge.

26.73 Fabrication & Manufacturing of Prestressed Hollow

Core slab (Hollow area 25 to 30%) of different thickness
& modular width 1200 mm in Controlled Factory
Environment with approved methodology confirming to
IS 10297:1982 by using long line casting method having
arrangement of proper steel bed. Concreting should be
done by batch mixing plant capable of producing zero
slump concrete, transported through automatic
shuttels of standard make & layed on bed with the help
of extruder/ Slipformer, finishing, curing and also
provision of steam curing. Cutting, making necessary
cutout/ holes of required sizes for services in slab
element after achieving required strength, yard
handling & stacking all complete as per approved shop
drawings & design mix as per the direction of the
Engineer-in-charge. (Cost of strands should be paid
separately).

Note: Excess/less cement over the specified cement

content used as per design mix is payable/ recoverable
separately)
26.73.1 Concrete Grade-M-40 (cement content 400 kg)
26.73.1.1 100 mm thick hollow core slab 1.00 m 1287.25 One Metre 1287.00
26.73.1.2 120 mm thick hollow core slab 1.00 m 1501.40 One Metre 1501.00
26.73.1.3 150 mm thick hollow core slab 1.00 m 1822.60 One Metre 1823.00
26.73.1.4 200 mm thick hollow core slab 1.00 m 2217.00 One Metre 2217.00
26.73.1.5 250 mm thick hollow core slab 1.00 m 2717.10 One Metre 2717.00
26.73.1.6 300 mm thick hollow core slab 1.00 m 3217.20 One Metre 3217.00
26.73.1.7 350 mm thick hollow core slab 1.00 m 3717.25 One Metre 3717.00
26.73.1.8 400 mm thick hollow core slab 1.00 m 4217.35 One Metre 4217.00
26.73.2 Extra for using M-50 (Cement content 425 kg) instead
of M-40
26.73.2.1 100 mm thick hollow core slab 1.00 m 18.42 One Metre 18.00

DSR - 2023 IN MS EXCEL Page 249 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.73.2.2 120 mm thick hollow core slab 1.00 m 22.10 One Metre 22.00
26.73.2.3 150 mm thick hollow core slab 1.00 m 27.65 One Metre 28.00
26.73.2.4 200 mm thick hollow core slab 1.00 m 34.40 One Metre 34.00
26.73.2.5 250 mm thick hollow core slab 1.00 m 43.00 One Metre 43.00
26.73.2.6 300 mm thick hollow core slab 1.00 m 51.60 One Metre 52.00
26.73.2.7 350 mm thick hollow core slab 1.00 m 60.20 One Metre 60.00
26.73.2.8 400 mm thick hollow core slab 1.00 m 68.80 One Metre 69.00
26.73.3 Extra for using M-60 (Cement content 440 kg) instead
of M-40
26.73.3.1 100 mm thick hollow core slab 1.00 m 29.50 One Metre 30.00
26.73.3.2 120 mm thick hollow core slab 1.00 m 35.35 One Metre 35.00
26.73.3.3 150 mm thick hollow core slab 1.00 m 44.20 One Metre 44.00
26.73.3.4 200 mm thick hollow core slab 1.00 m 55.00 One Metre 55.00
26.73.3.5 250 mm thick hollow core slab 1.00 m 68.80 One Metre 69.00
26.73.3.6 300 mm thick hollow core slab 1.00 m 82.55 One Metre 83.00
26.73.3.7 350 mm thick hollow core slab 1.00 m 96.30 One Metre 96.00
26.73.3.8 400 mm thick hollow core slab 1.00 m 110.05 One Metre 110.00
26.74 Fabrication and manufacturing of solid precast concrete
element with provisions of shear keys, connecting
loops, dowel tubes and proper lifting accessories for
walls, beams, slabs, stairs, column etc, of various
thickness, shape and size of different concrete grades
manufactured in controlled factory environment with
approved methodology including moulds (Pallet system,
Tilts form, table moulds, battery moulds, vertical
moulds, beam moulds, column moulds, staircase
moulds, Facade mould, etc.), mixing, transporting and
placing of concrete, vibrating, curing, finishing, making
necessary cutout/holes of required sizes for services,
yard handling & stacking all complete as per IS
11447:1985 and as per approved shop drawings and
design mix as per the direction of Engineer-in-Charge
(Cost of reinforcement, Mechanical, Electrical and
Plumbing inserts will be paid separately).

26.74.1 Concrete grade M-35 (Cement content 370 kgs) 1.00 Cum 20928.70 One Cubic 20929.00
Metre
26.74.2 Extra for using M-40 (Cement content 400 kg) instead 1.00 Cum 245.65 One Cubic 246.00
of M-35 Metre
26.74.3 Extra for using M-50 (Cement content 425 kg) instead 1.00 Cum 450.40 One Cubic 450.00
of M-35 Metre
26.74.4 Extra for using M-60 (Cement content 440 kg) instead 1.00 Cum 573.20 One Cubic 573.00
of M-35 Metre
26.75 Providing & laying in position Prestressing steel strands 1.00 Kg 192.35 One Kilogram 192.00
(low relaxation) on hollow core bed by using
mechanical pulling arrangement like Rabbit/ Bed
master including all accessories for Stressing &
destressing operations as per approved make
conforming to IS1343 & grade FY-1860 etc, complete as
per drawings and direction of Engineer -in-charge.

26.76 Transportation of Precast Elements by flat bed Trailor

(Double / Triple axle 40ft Length with proper
accessories like A frame etc) from factory, including the
cost of loading , unloading & stacking at site with the
help of required capacity cranes.

26.76.1 Lead within 15km 1.00 MT 540.85 One Metric 541.00

Tonne
26.76.2 Add/Deduct over item 26.76.1 for every additional lead 1.00 MT 117.30 One Metric 117.00
of 5 km Tonne

DSR - 2023 IN MS EXCEL Page 250 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.77 Erection & Installation of Precast/Prestressed Concrete
elements in correct & final position with proper line
level and plumb at site making all arrangements (i.e
cranes, push-pull jacks & all another T & P for lifting
Placing & Alignment of elements, within erection
tolerance as per IS 15916 as per approved shop
drawings and all complete as per the direction of
Engineer-in-Charge but excluding the cost of sim pads,
non shrink grout and steel works i.e hangers. All work
up to fifth floor.

26.77.1 Prestressed hollow core Slab up to 200 mm thickness 1.00 Sqm 203.50 One Square 204.00
Metre
26.77.2 Prestressed hollow core slab above 200 mm up to 400 1.00 Sqm 345.15 One Square 345.00
mm thickness Metre
26.77.3 Solid concrete wall elements 1.00 Cum 2720.30 One Cubic 2720.00
Metre
26.78 Providing & Applying weather proof sealant on outer
joints of approved make confirming to IS & directed by
Engineer-in-charge.
26.78.1 Sealant 25mmx10mm at joints 1.00 m 178.95 One Metre 179.00
26.79 Providing & Laying of levelling sim pads required sizes
(5x5cm to 10x10cm) of PVC / Rubber to adjust level of
bearing surface of supporting members as per the
direction of Engineer in charge.

26.79.1 2mm thick 1.00 No. 28.90 Each 29.00

26.79.2 5mm thick 1.00 No. 36.00 Each 36.00
26.79.3 10mm thick 1.00 No. 51.65 Each 52.00
26.80 Providing & Grouting of dowel tubes / Shear keys /
Joints of precast members with M-60 grade
cementitious grout (Non Shrink) of approved make by
suitable means ( Free flowing /pump),curing etc.
Complete as per directions of Engineer-in-charge. (The
payment shall be made on the basis of actual weight of
approved grout injected.)

26.80.1 Stirrer mixed cementitious grout (non shrink) of 1.00 Kg 85.05 One Kilogram 85.00
approved make in dowel tubes / Shear keys / Joints of
precast members.
26.81 Providing and fixing Scaffolding net of required width 1.00 Sqm 29.25 One Square 29.00
made of high density Polyethylene UV stabilized knitted Metre
on warp knitting machines having density
100grams/sqm and shading coefficient minimum 75%
around the construction site/ for vertical extension as
per requirement including fastening/tying with
uilding/scaffolding pipes or with any other fixtures etc.
complete as per direction of Engineer-in-Charge. (One
time payment shall be made for providing Scaffolding
net from start of work till completion of work including
shifting if any. The Scaffolding net shall be the property
of the contractor on completion of the work

DSR - 2023 IN MS EXCEL Page 251 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.82 Providing and laying rigid EPS (cellular plastic material)
blocks conforming to ASTM standards/specifications of
minimum density 21.60 Kg/cum on floors, steps, stage
etc. of required size and shape as per direction of the
Engineer-in-Charge. This shall include the following
operation. “The EPS blocks shall be cut to required
shape and sizes including cuttings for passing of
services, joined together with synthetic resin adhesives
as per relevant specifications and packed/placed in
position for stepped floor or platform formation. The
top and sides surfaces to be provided with GI woven
wire mesh of aperture 5.45 mm (with wire dia 0.90 mm)
secured to EPS blocks with wire pins/clips. Horizontal
top surface to be provided with 20 mm thick cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate upto 6mm chippings) and vertical
surface to be provided with 12mm cement plaster 1:4
(1 cement : 4 coarse sand).

The concrete/plastered surfaces so prepared shall be 1.00 Sqm 2293.30 One Square 2293.00
scratched with wire brushes to form burrs, so as to act Metre
as base for flooring or veneering/panelling to be done
later as per approved design (which shall be paid for
separately complete as per direction of the Engineer-in-
Charge.

26.83 Applying stamping finish to the top surface of freshly

laid plain / reinforced cement concrete of specified
grade in portico, side walks, drive ways, pool decks and
open yard as per direction of the Engineer-in-Charge.

* The concrete shall be placed and screened to the

finished grade and floated to the uniform surface by
using standard finishing techniques. approved color
hardener @ 2.7 kg/sqm shall be applied evenly to the
surface of the fresh concrete by the dry shake method
by sprinkling in twoor more shakes floated after each
shake and trowel only after final floating. The approved
released agent @ 0.113 Kg/Sqm shall be applied evenly
to the trowelled surface before stamping or the said
release agent can be applied to the flexible
polyurethene stamp moulds of approved design and in
required sizes to achieve final stamping pattern. These
stampings shall be placed on the surface of concrete in
three to four pieces at a time and tapped gently with
rammers of sufficient size and weight to leave proper
stamp marks and the process repeated for the
remaining concrete surface till the whole surface to be
stamped is completed within the time while the
concrete is in plastic stage of setting.

* After stamping, the curing shall be done as per

manufacturers specifications. After initial curing the
imprinted joints shall be grouted using cement slurry
mixed with color hardener as per the requirement. The
surface shall be sealed by applying acrylic based sealer
not less than 0.167 litre/Sqm on finished surface.

DSR - 2023 IN MS EXCEL Page 252 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
* The construction joints shall be provided by grove 1.00 Sqm 762.75 One Square 763.00
cutting of size 4 mm x 20 mm in panel size 3 m x 3 m or Metre
lesser as per the site conditions and filling the same
with 10 mm baker rod and providing & laying (PU)
Polyurethane based joint sealer of approved make as
per manufacturer’s specifications and finished by
applying polyurethene resin based topprotective clear
coat of minimum 80 micron applied with rollers on
properly cured and dry clean surface. (The cost of
concrete for flooring is not included in the item, which
shall be paid for seperately).

26.84 Supplying and laying of Uni-Axial Woven Polyster

Geogrid conforming to MORTH 3100 and IRC113, as soil
reinforcement/basal reinforcement including
accessories like tie-strips, nuts & bolts and loops/lugs
for joining reinforcing elements with the facia pannels,
overlaps and other protective elements for synthetic
geo-grids and all other activities required for reinforced
soil walls, slopes etc complete as per design
requirements, manufacturer specifications and as per
direction of engineer-in- charge.

26.84.1 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 271.45 One Square 271.00
strength 40KN/m in the Longitudinal direction and 20 Metre
KN/m in the Transverse direction.
26.84.2 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 310.30 One Square 310.00
strength 60KN/m in the Longitudinal direction and 20 Metre
KN/m in the Transverse direction.
26.84.3 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 385.00 One Square 385.00
strength 80 KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.
26.84.4 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 440.25 One Square 440.00
strength 100KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.
26.84.5 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 470.10 One Square 470.00
strength 120KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.
26.84.6 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 580.65 One Square 581.00
strength 150KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.
26.84.7 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 677.75 One Square 678.00
strength 200KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.
26.84.8 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 819.65 One Square 820.00
strength 250KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.
26.84.9 Uni Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 942.15 One Square 942.00
strength 300KN/m in the Longitudinal direction and 30 Metre
KN/m in the Transverse direction.

DSR - 2023 IN MS EXCEL Page 253 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.85 Supplying and laying of Bi-Axial Woven Polyster Geogrid
conforming to MORTH 3100 and IRC113, as soil
reinforcement/basal reinforcement of granular road
base and sub base, area stalilization, track bed
stabilization, load transfer platforms Including
accessories like tiestrips, nuts & bolts and loops/lugs for
joining reinforcing elements with the facia pannels,
overlaps and other protective elements for synthetic
geo-grids and all other activities required etc. complete
as per design requirements, manufacturer
specifications and as per direction of engineer-in-
charge.

26.85.1 Bi Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 229.65 One Square 230.00
strength 20KN/m in both Longitudinal and Transverse Metre
direction.
26.85.2 Bi Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 329.70 One Square 330.00
strength 40KN/m in both Longitudinal and Transverse Metre
direction.
26.85.3 Bi Axial Woven polyster geogrid of minimum tensile 1.00 Sqm 416.35 One Square 416.00
strength 60KN/m in both Longitudinal and Transverse Metre
direction.
26.86 Providing and fixing factory made single extruded WPC
(Wood Polymer Composite) solid door/ window/
Ceosetory windows & other Frames/ Chowkhat
comprising of virgin PVC polymer of K value 58-60
(Suspension Grade), calcium carbonate and natural
fibers (wood powder/ rice husk/ wheat husk) and non
toxic additives (maximum toxicity index of 12 for 100
gms) fabricated with miter joints after applying PVC
solvent cement and screwed with full body threaded
star headed SS screws having minimum frame density
of 750 kg/cum, screw withdrawal strength of 2200 N
(Face) & 1100 N (Edge), minimum compressive strength
of 58 N/mm2, modulus of elasticity 900 N/mm2 and
resistance to spread of flame of Class A category with
property of being termite/ borer proof, water/ moisture
proof and fire retardant and fixed in position with M.S
hold fast/ lugs/ SS dash fasteners of required dia and
length complete as per direction of Engineer-In- Charge.

(M.S hold fast/ lugs or SS dash fasteners shall be paid

for separately). Note: For WPC solid door/ window
frames, minus 5mm tolerance in dimensions i.e depth
and width of profile shall be acceptable. Variationin
profile dimensions on plus side shall be acceptable but
no extra payment on this account shall be made.

26.86.1 Frame size 45 x 70 mm 1.00 m 705.85 One Metre 706.00

26.86.2 Frame size 45 x 85 mm 1.00 m 926.35 One Metre 926.00
26.86.3 Frame size 50 x 100 mm 1.00 m 947.70 One Metre 948.00
26.86.4 Frame size 50 x 125 mm 1.00 m 1075.70 One Metre 1076.00
26.86.5 Frame size 65 x 100 mm 1.00 m 1111.30 One Metre 1111.00
26.86.6 Frame size 65 x 125 mm 1.00 m 1381.60 One Metre 1382.00
26.86.7 Frame size 65 x 150 mm 1.00 m 1637.65 One Metre 1638.00

DSR - 2023 IN MS EXCEL Page 254 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.87 Providing and fixing factory made single extruded WPC
(Wood Polymer Composite) solid plain flush door
shutter of required size comprising of virgin polymer of
K value 58-60 (Suspension Grade), calcium carbonate
and natural fibers (wood powder/ rice husk/ wheat
husk) and non toxic additives (maximum toxicity index
of 12 for 100 gms) having minimum density of 650
kg/cum and screw withdrawal strength of 1800 N (Face)
& 900 N (Edge), minimum compressive strength 50
N/mm2, modulus of elasticity 850 N/mm2 and
resistance to spread of flame of Class A category with
property of being termite/borer proof, water/ moisture
proof and fire retardant and fixing with stainless steel
butt hinges of required size with necessary full body
threaded star headed counter sunk S.S screws, all as per
direction of Engineer-In- Charge.

(Note: stainless steel butt hinges and necessary S.S

screws shall be paid separately)
26.87.1 30 mm thick 1.00 Sqm 4346.70 One Square 4347.00
Metre
26.87.2 35 mm thick 1.00 Sqm 5015.35 One Square 5015.00
Metre
26.88 Providing and fixing factory made single extruded WPC
(Wood Polymer Composite) solid decorative type flush
door shutter of required size comprising of virgin
polymer of K value 58-60 (Suspension Grade), calcium
carbonate and natural fibers (wood powder/ rice
husk/wheat husk) and non toxic additives (maximum
toxicity index of 12 for 100 gms) having minimum
density of 650 kg/cum and screw withdrawal strength
of 1800 N (Face) & 900 N (Edge), minimum compressive
strength 50 N/mm2, modulus of elasticity 850 N/mm2
and resistance to spread of flame of Class A category
with property of being termite/borer proof,
water/moisture proof and fire retardant. WPC to be
laminated with PVC foil of minimum 14 microns thick of
approved design pasted with hot melt adhesive on both
faces of shutter and fixing with stainless steel butt
hinges of required size with necessary full body
threaded star headed counter sunk S.S screws, all as per
direction of Engineer-In- Charge. (Note: stainless steel
butt hinges and necessary S.S screws shall be paid
separately)

26.88.1 30 mm thick 1.00 Sqm 4764.20 One Square 4764.00

Metre
26.88.2 35 mm thick 1.00 Sqm 5432.85 One Square 5433.00
Metre

DSR - 2023 IN MS EXCEL Page 255 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.89 Providing and fixing factory made single extruded WPC
(Wood Polymer Composite) solid board one side white
color and other side of board laminted with PVC foil of
minimum 14 micron thickness of approved design
pasted with hot melt adhesive for cup boards, work
stations and bathroom/kitchen cabinet etc. of required
sizes comprising of virgin polymer of K value 58-60
(Suspension Grade), calcium carbonate and natural
fibers (wood powder/ rice husk/wheat husk) and non
toxic additives (maximum toxicity index of 12 for 100
gms) having minimum density of 650 kg/cum and screw
withdrawal strength of 1800 N (Face) & 900 N (Edge),
minimum compressive strength 50 N/mm2, modulus of
elasticity 850 N/mm2 and resistance to spread of flame
of Class A category with property of being
termite/borer proof, water/ moisture proof and fire
retardant and fixing with stainless steel piano
hinges/soft close clip on concealed hinges of required
size with necessary full body threaded star headed
counter sunk S.S screws, all as per direction of
Engineer-In- Charge.

(Note: stainless steel piano hinges/soft close clip on

concealed hinges and necessary S.S screws shall be paid
separately)
26.89.1 18 mm thick 1.00 Sqm 2992.90 One Square 2993.00
Metre
26.89.2 25 mm thick 1.00 Sqm 3889.15 One Square 3889.00
Metre
26.90 Providing and fixing factory made single extruded WPC
(Wood Polymer Composite) solid plain white color
board for backing of cup boards and bathroom/kitchen
cabinets etc. of required size comprising of virgin
polymer of K value 58-60 (Suspension Grade), calcium
carbonate and natural fibers (wood powder/ rice
husk/wheat husk) and non toxic additives (maximum
toxicity index of 12 for 100 gms) having minimum
density of 650 kg/cum and screw withdrawal strength
of 1800 N (Face) & 900 N (Edge), minimum compressive
strength 50 N/mm2, modulus of elasticity 850 N/mm2
and resistance to spread of flame of Class A category
with property of being termite/borer proof,
water/moisture proof and fire retardant and fixing with
stainless steel screws etc. all as per direction of
Engineer-In- Charge. (Note: stainless steel screws shall
be paid separately)

26.90.1 6 mm thick 1.00 Sqm 1099.35 One Square 1099.00

Metre
26.90.2 12 mm thick 1.00 Sqm 1711.10 One Square 1711.00
Metre

DSR - 2023 IN MS EXCEL Page 256 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.91 Providing and fixing factory made 18 mm thick single
extruded WPC (Wood Polymer Composite) solid plain
white colour board Jali, CNC (Computer numeric
control) routed of approved design by Engineer-in -
charge which are machine cut for duct/shaft covering,
partitions and facades comprising of virgin polymer of K
value 58-60 (Suspension Grade), calcium corbonate and
natural fibers (wood powder/ rice husk/wheat husk)
and non toxic additives(maximum toxicity index of 12
for 100 gms) having minimum density of 650 kg/cum
and screw withdrawal strength of 1800 N (Face)
minimum compressive strength 50 N/mm2, modulus of
elasticity 850 N/mm2 and resistance to spread of flame
of Class A category with properties of being
termite/borer proof, water/moisture proof and fire
retardant and fixing on M.S (mild steel) frame made of
25 x 25 x 1.5 mm square hollow box section including
applying a priming coat of approved steel primer,
placed at grid made at 1.0 x 1.0 m or as per
requirement at site with necessary stainless steel
fasteners and SS screws etc., all complete as per
direction of Engineer-In- Charge.

(Note: M.S (mild steel) framework with priming coat 1.00 Sqm 3437.15 One Square 3437.00
and necessary SS fasteners and SS screws shall be paid Metre
separately.
26.92 Providing and fixing of façade at all heights with
extruded hollow Clay / Terracotta ventilated rainscreen
tiles of height 250/ 300/ 400mm and length of 595 mm
of approved texture,design and pattern having Flexural
Strength/ Modulus of Rupture of ? 14 N/m² and
maximum water absorption of 10% tested as per ISO
10545-4:2004(E) and ISO 10545-3:1995 respectively in
true level fixed to a supporting aluminium
framework(Alloy 6063 T5/T6) consisting of vertical 'T'
(for intermediates)/ 'L'(for ends/ termination)/ Tubular
sections (at corners)of size 80x60x2mm/ 40x60x2mm/
40x40x2mm respectively, spaced at maximum spacing
of 600mm c/c matching to the tile vertical grid, and
horizontal aluminium 'C'-clamps of size 56x25x2mm
thickness of length 150mm at junction of tiles and of
length 75mm at wall ends/ corners fixed on top of the
vertical sections at spacing of 250/ 300/ 400mm c/c
matching to the tile horizontal grid with two numbers
of self-drilling / self-tapping SS screws of size 5.5x25
mm with EPDM washers.

DSR - 2023 IN MS EXCEL Page 257 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
The vertical 'T'/'L/ Tubular' sections shall be fixed to the
wall using HDG (hot-dip-galvanized) steel L-brackets
(galvanizing thickness of minimum 80 microns)of size
110x80x6 mm at intermediate vertical aluminium
profiles and of size 220x110x12mm at outer corners
and stainless steel grade 304,M10 full threaded anchor
fasteners with nylon sleeve 100mm long (for brick
work) and M8 expansion anchor fasteners 75mm long
for concrete surface, spacing of brackets to be based on
a structural/ static calculation. The brackets shall be of
length 175mm at junction of two vertical aluminium
profiles and of length 100mm at intermediate points of
vertical profiles and shall be fixed to the vertical
aluminium T / L /Tubular profiles using two numbers
self-drilling/ self-tapping SS screws of size 5.5x25mm
with EPDM washers. EPDM gaskets to be fixed in
between brackets and vertical profiles. The tiles shall be
mounted on the ‘C’ clamps such that the tiles are
supported at top and bottom at both ends.

The tiles shall be additionally secured to the horizontal

‘C’ clamps using special SS clips of required size which
shall be inserted and pressed into position on the ‘C’
clamps holding the tiles and the cut-tiles shall be glued
at points to the horizontal ‘C’ clamps by using MS
Polymer sealant adhesive. The vertical joint open
groove between two adjacent tiles shall be 5mm. The
tiles and system shall be designed to resist wind load as
per IS 875 (Part 3) according to different zones. The tiles
shall be installed using the ventilated rain screen
principle with provision for natural ventilation of the
space between the façade tiles and the structural wall.
The work shall be carried out as per specification,
drawing and as per direction of the Engineer-in-Charge.
Note : Scaffolding wherever required to be paid
separately.

26.92.1 With 16mm thickness (+/- 10%) terracotta tiles of grey 1.00 Sqm 6320.00 One Square 6320.00
colour Metre
26.92.2 With 16mm thickness (+/- 10%) terracotta tiles of other 1.00 Sqm 5991.40 One Square 5991.00
than grey colour Metre

DSR - 2023 IN MS EXCEL Page 258 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.93 Providing and fixing of façade at all heights with
extruded hollow Clay / Terracotta ventilated rainscreen
tiles of height 259/ 309/ 409mm and lengthof 1190 mm
of approved texture,design and pattern having Flexural
Strength/ Modulus of Rupture of ? 14 N/m² and
maximum water absorption of 10% tested as per ISO
10545-4:2004(E) and ISO 10545-3:1995 respectively in
true level fixed to a supporting aluminium framework
(Alloy 6063 T5/T6) consisting of vertical 'T' (for
intermediates)/ 'L' (for ends/ termination)/ Tubular
sections (at corners)of size 80x60x2mm/ 40x60x2mm/
40x40x2mm respectively, spaced at maximum spacing
of 1200mm c/c matching to the tile vertical grid, and
horizontal aluminium 'C'-clamps of size 56x34x2mm
thickness of length 150mm at junction of tiles and of
length 75mm at wall ends/ corners fixed on top of the
vertical sections at spacing of 250/ 300/ 400mm c/c
matching to the tile horizontal grid with two numbers
of self-drilling / self-tapping SS screws of size 5.5x25
mm with EPDM washers.

The vertical 'T'/'L/ Tubular' sections shall be fixed to the

wall using HDG (hot-dip-galvanized) steel Lbrackets
(galvanizing thickness of minimum 80 microns) of size
110x80x6 mm at intermediate vertical aluminium
profiles and of size 220x110x12 mmat outer corners
and stainless steel grade 304,M10 full threaded anchor
fasteners with nylon sleeve 100mm long (for brick
work) and M8 expansion anchor fasteners 75mm long
for concrete surface, spacing of brackets to be based on
a structural/ static calculation. The brackets shall be of
length 175mm at junction of two vertical aluminium
profiles and of length 100mm at intermediate points of
vertical profiles and shall be fixed to the vertical
aluminium T / L / Tubular profiles using two numbers
self-drilling/ self-tapping SS screws of size 5.5x25 mm
with EPDM washers.“EPDM gaskets to be fixed in
between brackets and vertical profiles. The tiles shall be
mounted on the ‘C’ clamps such that the tiles are
supported at top and bottom at both ends. The tiles
shall be mounted on the Cclamps with EPDM profiles in
between such that the tiles are supported at top and
bottom at both ends. The vertical joint open groove
between two adjacent tiles shall be 10mm.

The tiles and system shall be designed to resist wind

load as per IS 875 (Part 3) according to different zones.
The tiles shall be installed using the ventilated rain
screen principle with provision for natural ventilation of
the space between the façade tiles and the structural
wall. The work shall be carried out as per specification,
drawing and as per direction of the Engineer-in-Charge.
Note: Scaffolding wherever required to be paid
separately.

26.93.1 With 24mm thickness (+/- 10%) terracotta tiles of grey 1.00 Sqm 6230.90 One Square 6231.00
colour Metre
26.93.2 With 24mm thickness (+/- 10%) terracotta tiles of other 1.00 Sqm 5842.50 One Square 5843.00
than grey colour Metre

DSR - 2023 IN MS EXCEL Page 259 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
26.94 Designing, shop fabricating, supplying , erecting, 1.00 Sqm 269.40 One Square 269.00
stripping and shifting of customized Modular Tunnel Metre
Formwork system for cast-in-situ monolithic RCC
structures, using precision steel cubical formworks are
molds with minimum 3mm thick hot rolled plain
painted/hot dip galvanized M.S. sheets for panel in
contact area with necessary framing and allied
accessories as per CPWD specifications including
transporting, storage, assembly, hoisting and placing in
position for supporting and holding the formwork in
place till initial setting of the concrete then stripping the
formwork, propping to support horizontal surface
cleaning and oiling etc. for shifting to the next cycle,
inclusive of all labour, machines and T&P requirements
taking all safety measures etc. as per design and cycle
programme all complete as per directions of the
Engineer-in-Charge. Design of Tunnel Formwork system
shall be provided by concerned service provider/
vendor and the rate is inclusive of all the elements and
all operations for all heights.

26.95 Providing and installation of factory made Structural

Stay in place form work system with double faced
panels for walls, single faced panels for roofs/floor
slabs, L shaped single faced panels for corners with
necessary scafolding, struts, bracing etc as per CPWD
specification and directions of the Engineer in Charge.
Design of walls and other members to be provided by
the supplier & shall be duly vetted by any engineering
institute of National repute such as IITs, NITs etc. and
nothing extra shall be payable on this account
(Additional steel reinforcement/dowels, design mix
concrete of specified grade, electrical and plumbing
conduits inserts for services and plastering on either
side of walls shall be paid for seperately).

NOTE: This item shall be adopted for building up to G+3

storey only excluding seismic zone V.
26.95.1 Double Panel of required thickness (110 mmor above) 1.00 Sqm 3189.10 One Square 3189.00
with minimum weight of panel as 11.05 kg per sqm for Metre
walls with corresponding corners and jambs strips.

26.95.2 Single panel for slabs with minimum weight of panel as 1.00 Sqm 1713.55 One Square 1714.00
4.05 kg/sqm for walls with corresponding corners and Metre
jambs strips.
26.96 Providing and placing 'Stay in Place PVC Wall formwork'
made up of extruded Unplasticised Poly Vinyl Chloride
(uPVC) consisting of Main panel, 3 way Connector,
Starter Channel, Joint Panel, Connection Panels,
Door/Window frame/trim panels etc. all complete as
per manufacturer design and for all heights as per
direction of Engineer-in-charge. (Note: Suitable for in fill
walls with appropriate Structural system).

26.96.1 125 mm wide Stay in Place PVC Wallform made of 1.00 Sqm 2926.70 One Square 2927.00
minimum 2.50 mm thick sections and minimum weight Metre
21.97 kg /sqm of formwork.
26.96.2 125 mm wide Stay in Place PVC Wallform made of 1.00 Sqm 3805.05 One Square 3805.00
minimum 2.50 mm thick sections and minimum weight Metre
21.97 kg /sqm of formwork.

DSR - 2023 IN MS EXCEL Page 260 of 265

 I.No. Description of Item Quantity Rate (Rs) Unit Amount(Rs)
Total of the Sub-Head - New Technologies And Materials : 358756.00

This Schedule has been prepared in Jalli's App - 2023 (Civil)

DSR - 2023 IN MS EXCEL Page 261 of 265

 DSR 2021 IN MS EXCEL WITH FORMULAS (Updated on 04.11.2023)
Read Me
01. This is a estimate proforma containing all the items of CPWD published DSR-2023, generated using Jalli's App - 2023
02. Data has been compiled and verified by many Engineers from BSNL and other Departments and from all over In
(see the table below)
03. Though, the data has been verified thoroughly, this file may contain certain mistakes/omissions.
Hence, the users of this file are advised to verify the correctness of the data with original DSR-2023 and Correcti
Slips (if any) published by CPWD.
04. Neither the author/publisher nor his associates, who compiled or verified the data for this file, are responsible
the damages/ losses whatsoever may be, that may occur directly or indirectly due to the incorrect data of this file.

05. This is not a replica of DSR-2023 published by the CPWD, but a standard Detailed Estimate Proforma which
normally used in Civil Engineering Departments of various Central / State Government or PSUs.
06. Please drop an e-mail to me at [email protected] for any queries regarding this file and confine your querry
this file only.
07. This file will be updated as and when errors are noticed and the file is corrected / CS is released for DSR-2023, ke
visiting our website www.jallisapp.com to download the updated version.

On behalf of all , my Sincere thanks to the following Officers who compiled / verified the data for making this file

Participated in compiling the data Sri / Smt

1 Nurul Haque, Kolkata
2 Sabya sachi mitra, Kolkata
3 Vijay Prakah Sharma, Ranchi, Jharkhand.
4 CRR Varma, Hyderabad, TS
5 G.Ashok Kumar, AP
6 K.Lakshmana Babu, Visakhapatnam, AP
7 Anurag Mishra, Gorakhpur UP.
8 Nandini Moorthy, Chennai
9 Kondal Rao P, Vijayawada, AP
10 K.Senthil Velan, TN
11 Anil Jotani, Rajkot, GJ.
12 Jitendra Singh, Kolkata.
13 Deepak Chaudhary
14 Vijay Kubhar, Tumkur, Karnataka.
15 Anup Pathak, Nagpur
16 Dilip Parwani
17 Pawan Kumawat, Jaipur
18 Vinod KV, Kerala
21 Sudheer Agrawal, Lucknow
22 Jitendra Jani, Ahmedabad
24 GDR Prasad AIR, Hyderabad
25 Pujan Kit CPWD, Kolkata
26 ST Patil DoP
27 Yogendra Kumar
-Rambabu Jalli
Hyderabad
e-mail : [email protected]
website : www.jallisapp.com
3)

nerated using Jalli's App - 2023.

artments and from all over India

/omissions.
riginal DSR-2023 and Correction

for this file, are responsible for

the incorrect data of this file.

ed Estimate Proforma which is

t or PSUs.
is file and confine your querry to

S is released for DSR-2023, keep

d the data for making this file!