Body styles to meet your needs.

This Tufline valve is available in three different body styles

and a variety of seat materials.

Wafer Style.
Figure numbers
801, 803, and 806.
The snap-in seat retainer
ring provides a full 100%
gasket sealing width.

Lug Style with snap-in

retainer.
Uni-directional dead end service.

Cryogenic. Figure numbers 811, 813, and 816.

Designated for full pressure dead
Both full and semi-cryogenic end service with the seat retainer
models are available. The bodies ring located against the upstream
are stainless steel. The seats are flange. The snap-in seat retainer
a combination of stainless steel ring provides a full 100% gasket
and Kel-F. Axially pliant sealing sealing width.
assures tight shutoff.
See Xomox Bulletin 333767
for additional information.

Lug Style with bolted

retainer.
Bi-directional dead end service.
Figure numbers 821 and 823.
Designated for full pressure dead
end service with the seat retainer
ring located either against the
Rail tank car. upstream flange or exposed
This bottom-mounted, bottom- downstream.
operated Tufline valve is available The screw-affixed seat retainer ,-
Q-

with a steam jacketed body and ring provides a minimum

a steam traced shaft and disc, 65% gasket sealing width, as
as well as a stainless steel body specified by API 609. 9
 Tufline High Performance Butterfly Valve Specifications
Typical ST seat specification. Typical FT seat specification. Typical HT seat specification.
1.0 Scope 1.0 Scope 1.0 Scope
This specification covers the design and testing of This specification covers the design and testing This specification covers the design and testing
high pressure offset seat butterfly valves. of high pressure offset seat butterfly valves. of high pressure offset seat butterfly valves.

2.0 Applicable Standards 2.0 Applicable Standards 2.0 Applicable Standards

The following standards shall apply: The following standards shall apply: The following standards shall apply:
ASME B16.5: Pipe Flanges and Flanged Fittings ASME B16.5: Pipe Flanges and Flanged Fittings ASME B16.5: Pipe Flanges and Flanged Fittings
(24” size and smaller) (24” size and smaller) (24” size and smaller)
ASME B16.34: Valves - Flanged and ASME B16.34: Valves - Flanged and ASME B16.34: Valves - Flanged and
Buttwelding End Buttwelding End Buttwelding End
MSS SP-25: Standard Marking System for Valves, MSS SP-25: Standard Marking System for Valves, ASME/FCI 70-2: Control Valve Seat Leakage
Fittings, Flanges, and Unions Fittings, Flanges, and Unions MSS SP-25: Standard Marking System for Valves,
MSS SP-61: Pressure Testing of Steel Valves MSS SP-61: Pressure Testing of Steel Valves Fittings, Flanges, and Unions
MSS SP-68: High Pressure - Offset Seat MSS SP-68: High Pressure - Offset Seat MSS SP-68: High Pressure - Offset Seat
Butterfly Valves Butterfly Valves Butterfly Valves
API 598: Valve Inspection and Testing API 598: Valve Inspection and Testing API 609: Butterfly Valves, Lug-Type
API 609: Butterfly Valves, Lug-Type and API 607: Fire Test for Soft-Seated and Wafer-Type
Wafer-Type Quarter Turn Valves PED 97/23 EG: Pressure Equipment Directive
PED 97/23 EG: Pressure Equipment Directive API 609: Butterfly Valves, Lug-Type Annex II, Module H
Annex II, Module H and Wafer-Type
PED 97/23 EG: Pressure Equipment Directive 3.0 Design Requirements
3.0 Design Requirements Annex II, Module H 3.1 Valves shall be High Performance Butterfly with
3.1 Valves shall be High Performance Butterfly with offset seat and eccentric shaft.
offset seat and eccentric shaft. They shall be 3.0 Design Requirements They shall be capable of providing 10% of
capable of sealing against full differential 3.1 Valves shall be High Performance Butterfly with Class IV shutoff in either flow direction.
pressure in either flow direction. offset seat and eccentric shaft. They shall be 3.2 Valve seat shall be both self and pressure
3.2 Valve seat shall be both self and pressure capable of sealing against full differential energized with two (2) metal sealing points
energized with an inert, fiberglass core. pressure in either flow direction. in contact with the disc at all times.
The self-energizing Fiberglass member shall be 3.2 Valve seat shall be both self and pressure 3.3 Valves shall have retained top and
isolated from the line media. energized with two (2) metal sealing points bottom low-friction bearings.
3.3 Valves shall have retained top and bottom and one (1) PTFE or similar material insert 3.4 Shaft design shall be single or dual piece.
low-friction bearings. in contact with the disc at all times. 3.5 Seat retainer rings must be recessed in
3.4 Shaft design shall be single or dual piece. 3.3 Valves shall have retained top and the body so the flange gasket prevents
3.5 Seat retainer rings must be recessed in the bottom low-friction bearings. any potential external leakage.
body so the flange gasket prevents any 3.4 Shaft design shall be single or dual piece. 3.6 Valves shall have internal over-travel
potential external leakage. 3.5 Seat retainer rings must be recessed stops to prevent the disc from rotating
3.6 Valves shall have internal over-travel stops in the body so the flange gasket prevents through the seats.
to prevent the disc from rotating through any potential external leakage. 3.7 Valves shall be Tufline or approved equal.
the seats. 3.6 Valves shall have internal over-travel
3.7 Valves shall be Tufline or approved equal. stops to prevent the disc from rotating 4.0 Materials of Construction
through the seats. 4.1 Valves shall be constructed using new
4.0 Materials of Construction 3.7 Valves shall be Tufline or approved equal. materials and components.
4.1 Valves shall be constructed using 4.2 Carbon steel valves shall be constructed
new materials and components. 4.0 Materials of Construction from the following materials:
4.2 Carbon steel valves shall be constructed 4.1 Valves shall be constructed using new 4.2.1 Body - ASTM A216 Grade WCB
from the following materials: materials and components. 4.2.2 Disc - ASTM A351 Grade CF-8M
4.2.1 Body - ASTM A216 Grade WCB 4.2 Carbon steel valves shall be constructed 4.3 Stainless steel valves shall be constructed
4.2.2 Disc - ASTM A351 Grade CF-8M from the following materials: from the following materials:
4.3 Stainless steel valves shall be constructed 4.2.1 Body - ASTM A216 Grade WCB 4.3.1 Body - ASTM A351 Grade CF-8M
from the following materials: 4.2.2 Disc - ASTM A351 Grade CF-8M 4.3.2 Disc - ASTM A351 Grade CF-8M
4.3.1 Body - ASTM A351 Grade CF-8M 4.3 Stainless steel valves shall be constructed 4.4 Shafts shall be ASTM A564 Type 630,
4.3.2 Disc - ASTM A351 Grade CF-8M from the following materials: H 1075 or H 1150-M (17-4PH) SS.
4.4 Shafts shall be ASTM A564 Type 630, 4.3.1 Body - ASTM A351 Grade CF-8M
H 1075 (17-4PH) SS or 316 SS. 4.3.2 Disc - ASTM A351 Grade CF-8M 5.0 Inspection and Testing
4.4 Shafts shall be ASTM A564 Type 630, 5.1 Valves shall be hydrostatically shell
5.0 Inspection and Testing H 1075 or H 1150-M (17-4PH) SS. tested per ASME B16.34 and MSS SP-61.
5.1 Valves shall be hydrostatically shell 5.2 Valves shall be seat tested per
tested per ASME B16.34 and MSS SP-61. 5.0 Inspection and Testing ASME/FCI 70-2 to 10% of Class IV.
5.2 Valves shall be seat tested per ASME 5.1 Valves shall be hydrostatically shell
B16.34 and MSS SP-61. No leakage is tested per ASME B16.34 and MSS SP-61. Sample Figure Number:
permitted for resilient seated valves. 5.2 Valves shall be seat tested per ASME B16.34 6” 801-267-SG-HT1-G
5.3 API 598 testing is available on request. and MSS SP-61. No leakage is permitted
for resilient seated valves.
Sample Figure Number: 5.3 API 598 testing is available on request.
6” 801-267-TT-ST2-L 5.4 Fire tested valves shall be qualified to
API 607, 4TH Edition fire test standard.

Sample Figure Number:

14 6” 801-267-SG-FT1-G
Cv Factors For Valve Sizing & Valve Weights
Cv factors are based on equivalent sized pipe.

Class 150 / 285rP Disc position - Degrees open Valve weight

Valve Valve
10o 20o 30o 40o 50o 60o 70o 80o 90o Wafer Lug
Size Size
2 4 10 19 29 46 65 94 125 152 2 7 10
3 7 19 37 56 90 127 184 244 296 3 10 14
4 12 33 64 98 157 222 321 425 517 4 19 24
5 19 51 102 154 247 351 507 671 816 5 29 35
6 32 85 166 255 409 581 839 1110 1350 6 29 35
8 55 146 289 439 702 996 1439 1905 2316 8 47 59
10 87 232 459 697 1116 1584 2287 3028 3682 10 75 88
12 125 334 660 1003 1604 2277 3289 4354 5295 12 107 137
14 172 461 910 1383 2213 3141 4537 6006 7303 14 150 215
16 224 599 1182 1797 2875 4082 5895 7805 9490 16 200 312
18 291 778 1536 2335 3735 5302 7658 10138 12328 18 268 405
20 360 962 1900 2888 4621 6559 9473 12542 15250 20 435 522
24 504 1348 2662 4046 6473 9188 13271 17569 21363 24 648 805

Class 300 / 740rP Disc position - Degrees open Valve weight

Valve Valve
10o 20o 30o 40o 50o 60o 70o 80o 90o Wafer Lug
Size Size
3 6 16 34 50 78 112 161 213 260 3 15 25
4 11 30 62 90 143 204 295 390 475 4 24 39
6 30 78 161 236 372 533 769 1017 1240 6 35 62
8 54 141 292 427 674 965 1392 1841 2245 8 59 93
10 84 222 458 669 1056 1514 2182 2886 3520 10 108 172
12 122 321 663 969 1530 2193 3162 4182 5100 12 158 288
14 142 380 750 1140 1824 2589 3739 4950 6019 14 232 443
16 186 498 984 1496 2394 3398 4907 6497 7900 16 430 622
18 239 639 1261 1917 3067 4353 6288 8324 10122 18 544 773
20 312 835 1649 2506 4009 5691 8220 10882 13232 20 645 810
24 440 1176 2321 3529 5645 8013 11574 15322 18631 24 1005 1574

Class 600 / 1480rP Disc position - Degrees open Valve weight

Valve Valve
10o 20o 30o 40o 50o 60o 70o 80o 90o Wafer Lug
Size Size
3 4 11 21 33 52 74 107 141 172 3 27 39
4 7 18 35 53 85 120 173 229 279 4 40 57
6 19 52 103 156 249 354 511 677 823 6 68 122
8 34 91 180 274 438 622 899 1190 1447 8 127 219
10 58 156 307 467 748 1061 1533 2029 2467 10 249 398
12 79 212 418 635 1016 1442 2082 2757 3352 12 337 580
14 103 283 553 850 1362 1933 2791 3695 4495 14 505 860
16 126 345 673 1035 1659 2354 3400 4500 5475
18 176 483 942 1448 2321 3294 4757 6297 7660
20 205 561 1095 1683 2698 3829 5530 7320 8905 For weights of valves
16 through 24 inches,
24 314 859 1677 2577 4131 5863 8467 11208 13635 contact Xomox Sales 15
Office.
 Carbon steel body Stainless steel body Seat type
1I-ZI-ZIIZII-
Below 800°F - 17-4 PH shaft |nCOne|

Above 800°F - lnconel shaft shaft

Soft seated valves, Fire tested and high temperature valves,

Class 600 Class 600

1 600 1 600

1 400 ,\ 1400 _'\

\\ ‘\
1200 1200 \
\ .
/
/
1 000 mini")-T
/‘L-’ 1 000
.._./_. ..l.._ I
so CDO O
!! \ _/
I
L8
OO O \ '\'l0 ¢-'at_
l§I§\/'/,./ \ CDO0
OO OO ‘iii. é?‘
drop-ps'g
$2 F
J

\ Q9
17-4 PH
shaft U1./V\
-l>O O \ -l>O O
¢W99
J

Prp
es-uredrop »<> Pres ure i_d.‘.1tL“ Edi-
200
’A\,
6‘
P99 200 35' §<E>
wasssotsELF135975
9'4?
._. _-—" 'z€ S
M i i |
-20 100 200 300 400 500 600 -20 200 400 600 800 1000
Temperature (degrees Fahrenheit) Temperature (degrees Fahrenheit)

Seat performance data Temperature limits of other components

Seat Maximum Minimum Test PTFE/316 SS (T): -50°F to +450°F
Type Temperature Temperature Leak Rate Bearings
ST1 400°F -50°F ZERO 316/SS/TM treated: -50°F to +1000°F

ST2 450°F -50°F ZERO PTFE V-rings: -50°F to +450°F

Packing
ST3 180°F -20°F ZERO Graphite: -50°F to +1000°F

ST6 250°F -20°F ZERO 17-4PH cond. 1075 -20°F to +800°F

Shafts
FT1 500°F -50°F ZERO 17-4PH cond. 1150-M -50°F to +800°F
Ambient temp. -20°F to
HT1 1000°F -50°F 10% of CL IV +200°F
Aluminum housing:
Max. pipeline temp. +300°F
ST20 600°F -20°F ZERO Gears
Ambient temp. -20°F to
FT20 600°F -20°F ZERO +200°F
Ductile iron housing:
Max. pipeline temp. +450°F

Note: Valves with reinforced PTFE (ST2) See Xomox Bulletin 334251 for details on
seats and PTFE/ 316 SS bearings can be the new XENITH XT soft seated and FT
used in saturated steam service up to 135 seated High performance Butterfly Valves for
psia and 350oF. Valves with Xomox 575 extended temperature applications.
(HT2) seats and 316 SS/TM treated bearings
can be used for saturated and super-heated
steam applications up to 575oF.
17
 Below is an example of the Tufline High Performance Butterfly Valve ordering code:

er e
Q" mi" ail‘
e“?

§
Oi 4
.nil?
5%»- §‘$'e,.%fl
‘
6
I-1
49; ...
?‘5l;tflH/fr:':¢¢"5’-35,
way; ‘file -§~"ef~fi$@
'"Fe “I-ff‘_ I -|
QB
_| ‘W
“‘{H
"-.__
"1 r'- -'-

Size Qif’__ Service

2 te 24 D:qrgen.....D
inehee '~.feeuum....
Chlorine. . . .
Style Mace . . . . . .
Steam - _ . . . General Notes:
High Tebaece. . . . Ahzhe
Perfurmenee General 1-A
 PI 609 face to face dimensions are
Butterlltr service - Blenl:
Valve standard. Any other face to face
requirements must be specified.
Aetuetien
None . . . . . . . . ..H 2-A
 luminum gear maximum 300°F line
Buclyr Type Lever . . . . . . . . . . L temperature. Use DI above 300°F.
Wafer. . . . . .0
Lug . . . . . . . 1
"te;eeteF
t3eer=*,........G
3-S
 ingle set. For double set with
lLlrhi-clire-:.-ticrnal leak-off consult factory. Not to be
deed end] Fewer eetueter. . A used when lever actuator is
Lug . . . . . - -2
|]Eli|:lire-etir:|nel
new em]
See required.
TFE . . . . . . . . . . . . - - ET1 4 - 350°F maximum in steam service.
Glass filled PTFE . . . STE
Cleee {Standard} 5-C
 onsult factory for P limitations on
Tufline~4?5 . . . . . . . . . BT15 shaft materials
l:|_15Cl'..._.1 Tulline-B00 . . . . . . . STEIII
L|HMWPE..........ST3 other than 17-4 PH.
GL3-l'.Il'Cl.....3
'GLE-ClD.....E 31E55r"F"TFE . . . . . . - - FT1 6 - Double length (XP) extended
MD-nell'PTFE . . . . . . - - FT3 packing (TFE) with live-loading
31EE5r'Tut'|inEr-Ei-l'JEl. . . FTEIII
bevel washers and monitoring port.
Be-dyr 31555 . . - - - . . . . . . .. HT1
Menel . . . . . . . . . . . .. HT3
Alley 20 . . . . .. 315-ESIPCFTE. . . . . . . GT4 For information on 30” - 48” Tufline
Gerhen steel .. Heinfureed TFM . . . . . . ST18 High Performance Butterfly Valves,
Menel . . . . . . .. Drtherfspeeilyl ...IlIl
see Xomox Brochure 335251.
30455 . . . . . .. Faeltlng
It-lielrel . . . . . . .. For sizes and materials
31555 . . . . . .. TFE V-rings . . . . . . T
Eil'E.lIl|"Ii'lE . . . . . . . . . . G
not shown, consult factory.
Heetelley El. . . .
Heetelley G. . lekehtinh rie PTFE live-leaded? -. L
Either fflpeeitiy} . I Erniesien Central. . .E"
Bearing
Dist: PTFEre1ees - . - . . .1 AWARNING
Alley 20 . . . . . . 31ES5.I'Tl'ul treated . . 5
For bi-directional dead end service,
Cerhen steel . .
Menel . . . . . . _ _ Shaft you must use body type 821, or 823
30455 . . . . . _ - valves. These valves have retainers
Alley ED
Nielrel . . . . . . . . Menel H-500. . . . . - specially designed for such service.
31555 . . . . . . . l'~li-el-rel . . Use of body type 811, 813, or 816
Heelelley B. . . . 31-If-SS. . valves in such service will result in
Heetelley G. . . . eeee IT"-=lFH. '~lU'IlLI'lHl massive leakage.
Either lfipecifiy} . it er-~=I-tr-15
Haetelle1.=B........B
He.-$lelle3rC........El
1?-4PH. . . . . . . . . --|'-l
r:-mt-|:|-11em.t
Either {Specify}- - - - -1

22