02/04/2021 ccna-200-301: 2.

0 Network Access Questions

Você acessou com

Home Meus Cursos

Página Inicial ► ccna-200-301 ► Questionários ► 2.0 Network Access Questions ► Tentativa 2

2.0 Network Access Questions - Tentativa 2

1 A Cisco IP phone receive untagged data traffic from an attached PC. Which action is taken by the phone?
Notas: --/1
Escolher uma resposta. a. It tags the traffic with the default VLAN
b. It tags the traffic with the native VLAN
c. It drops the traffic
d. It allows the traffic to pass through unchanged

Enviar

2 A network administrator is configuring an EtherChannel between SW1 and SW2. The configuration is shown bellow. Will this configura
Notas: --/1
both sides and same interfaces?

interface FastEthernet 0/1

channel-group 1 mode active
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface FastEthernet 0/2
channel-group 1 mode active
switchport trunk encapsulation dot1q
switchport mode trunk

Escolher uma resposta. a. It is not possible to state

b. Yes
c. No

Enviar

3 A network engineer must create a diagram of a multivendor network. Which command must be configured on the Cisco devices so tha
Notas: --/1
network can be mapped?

Escolher uma resposta. a. Device(Config)#lldp run

b. Device(Config-if)#cdp enable
c. Device(Config)#cdp run
d. Device(Config)#flow-sampler-map topology

Enviar

4 An administrator is tasked with configuring a voice VLAN. What is the expected outcome when a Cisco phone is connected to the Giga
Notas: --/1
switch?

int gig 0/1

switchport mode access
switchport voice vlan 51

Escolher uma resposta. a. The phone sends and receives data in VLAN 51, but a workstation connected to the phone sends an
VLAN 1
b. The phone and a workstation that is connected to the phone send and receive data in VLAN 51
c. The phone sends and receives data in VLAN 51, but a workstation connected to the phone has no VL
d. The phone and a workstation that is connected to the phone do not have VLAN connectivity

Enviar

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 1/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

5 An engineer is asked to protect unused ports that are configured in the default VLAN on a switch. Which two steps will fulfill the reques
Notas: --/1
Escolha pelo menos a. Enable the Cisco Discovery Protocol
uma resposta. b. Configure the ports as trunk ports
c. Administratively shut down the ports
d. Configure the ports in an EtherChannel
e. Configure the port type as access and place in VLAN 99

Enviar

6 An engineer must configure Interswitch VLAN communication between a Cisco switch and a third-party switch. Which action should be
Notas: --/1
Escolher uma resposta. a. configure ISL
b. configure DSCP
c. configure IEEE 802.1q
d. configure IEEE 802.1p

Enviar

7 An engineer must establish a trunk link between two switches. The neighboring switch is set to trunk or desirable mode. What action s
Notas: --/1
Escolher uma resposta. a. configure switchport mode dynamic auto
b. configure switchport trunk dynamic desirable
c. configure switchport nonegotiate
d. configure switchport mode desirable

Enviar

8 An engineer requires a scratch interface to actively attempt to establish a trunk link with a neighbor switch. What command must be co
Notas: --/1
Escolher uma resposta. a. switchport mode trunk
b. switchport mode dynamic desirable
c. switchport mode dynamic auto
d. switchport nonegotiate

Enviar

9 How can the Cisco Discovery Protocol be used?

Notas: --/1
Escolher uma resposta. a. all of the above
b. to determine the hardware platform of the device
c. to allow a switch to discover the devices that are connected to its ports
d. to determine the IP addresses of connected Cisco devices

Enviar

10 How does a switch interact with other switches in the same VTP domain when configured in transparent mode (vtp mode transparent)?
Notas: --/1
Escolher uma resposta. a. It processes VTP updates from any VTP clients on the network on its access ports
b. It forwards only the VTP advertisements that it receives on its trunk ports
c. It transmits and processes VTP updates from any VTP Clients on the network on its trunk ports
d. It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports

Enviar

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 2/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

11 How does CAPWAP communicate between an access point in local mode and a WLC?
Notas: --/1
Escolher uma resposta. a. The access point must not be connected to the wired network, as it would create a loop
b. The access point has the ability to link to any switch in the network, assuming connectivity to the WLC
c. The access point must directly connect to the WLC using a copper cable
d. The access point must be connected to the same switch as the WLC

Enviar

12 How does STP prevent forwarding loops at OSI Layer 2?

Notas: --/1
Escolher uma resposta. a. Blocking ports
b. Collision avoidance
c. MAC address forwarding
d. TTL

Enviar

13 In a CDP environment, what happens when the CDP interface on an adjacent device is configured without an IP address?
Notas: --/1
Escolher uma resposta. a. CDP operates normally, but it cannot provide any information for that neighbor
b. CDP operates normally, but it cannot provide IP address information for that neighbor
c. CDP becomes inoperable on that neighbor
d. CDP uses the IP address of another interface for that neighbor

Enviar

14 The network administrator wants VLAN 171 traffic to be untagged between Switch 1 and Switch 2 while all other VLANs are to remain
command accomplishes this task?
Notas: --/1

Escolher uma resposta. a. switchport trunk allowed vlan 171

b. switchport private-vlan association host 171
c. switchport access vlan 171
d. switchport trunk native vlan 171

Enviar

15 Two switches are connected and using Cisco Dynamic Trunking Protocol. SW1 is set to Dynamic Desirable. What is the result of this c
Notas: --/1
Escolher uma resposta. a. The link becomes a trunk port
b. The link is in an error disables stale
c. The link is in a down state
d. The link is becomes an access port

Enviar

16 What are two benefits of using VTP in a switching environment? (Choose two.)
Notas: --/1
Escolha pelo menos a. It allows ports to be assigned to VLANs automatically
uma resposta. b. It allows frames from multiple VLANs to use a single interface
c. It allows switches to read frame tags
d. It maintains VLAN consistency across a switched network
e. It allows VLAN information to be automatically propagated throughout the switching environment

Enviar

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 3/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

17 What are two reasons a network administrator would use CDP? (Choose two.)
Notas: --/1
Escolha pelo menos a. to verify Layer 2 connectivity between two devices when Layer 3 fails
uma resposta. b. to verify the type of cable interconnecting two devices
c. to obtain the IP address of a connected device in order to telnet to the device
d. to obtain VLAN information from directly connected switches
e. to determine the status of the routing protocols between directly connected routers
f. to determine the status of network services on a remote device

Enviar

18 What criteria is used first during the root port selection process?
Notas: --/1
Escolher uma resposta. a. lowest path cost to the root bridge
b. lowest neighbor’s port ID
c. local port ID
d. lowest neighbor’s bridge ID

Enviar

19 What is a benefit of using a Cisco Wireless LAN Controller?

Notas: --/1
Escolher uma resposta. a. Central AP management requires more complex configurations
b. Unique SSIDs cannot use the same authentication method
c. It eliminates the need to configure each access point individually
d. It supports autonomous and lightweight APs

Enviar

20 What is a difference between local AP mode and FlexConnet AP mode?

Notas: --/1
Escolher uma resposta. a. Local AP mode creates two CAPWAP tunnels per AP to the WLC
b. FlexConnect AP mode fails to function if me AP loses connectivity with the WLC
c. FlexConnect AP mode bridges the traffic from the AP to the WLC when local switching is configured
d. Local AP mode causes the AP to behave as if it were an autonomous AP

Enviar

21 What is the primary effect of the spanning-tree portfast command?

Notas: --/1
Escolher uma resposta. a. It immediately enables the port in the listening state
b. It minimizes spanning-tree convergence time
c. It immediately puts the port into the forwarding state when the switch is reloaded
d. It enables BPDU messages

Enviar

22 When a WPA2-PSK WLAN is configured in the Wireless LAN Controller, what is the minimum number of characters that is required in A
Notas: --/1
Escolher uma resposta. a. 8
b. 12
c. 18
d. 6

Enviar

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 4/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

23 When configuring a WLAN with WPA2 PSK in the Cisco Wireless LAN Controller GUI, which two formats are available to select? (Cho
Notas: --/1
Escolha pelo menos a. base64
uma resposta. b. ASCII
c. binary
d. decimal
e. hexadecimal

Enviar

24 When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?
Notas: --/1
Escolher uma resposta. a. Auto
b. Active
c. On
d. Desirable
e. Passive

Enviar

25 Which 802.11 frame type is association response?

Notas: --/1
Escolher uma resposta. a. protected frame
b. control
c. action
d. management

Enviar

26 Which action do the switches take on the trunk link when switch 1 is configured with native VLAN 99 (switchport trunk native 99) and s
999 (switchport trunk native 999) for the same trunk link?
Notas: --/1

Escolher uma resposta. a. The trunk does not form, but VLAN 99 and VLAN 999 are allowed to traverse the link
b. The trunk does not form and the ports go into an err-disabled status
c. The trunk forms but VLAN 99 and VLAN 999 are in a shutdown state
d. The trunk forms but the mismatched native VLANs are merged into a single broadcast domain

Enviar

27 Which command can be used if we can check the neighbor IP address?

Notas: --/1
Escolher uma resposta. a. show cdp neighbor
b. show cdp neighbor detail
c. show lldp
d. show interface

Enviar

28 Which command is used to enable LLDP globally on a Cisco IOS ISR?

Notas: --/1
Escolher uma resposta. a. lldp transmit
b. cdp enable
c. cdp run
d. lldp run
e. lldp enable

Enviar

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 5/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

29 Which command is used to specify the delay time in seconds for LLDP to initialize on any interface?
Notas: --/1
Escolher uma resposta. a. lldp reinit
b. lldp holdtime
c. lldp timer
d. lldp tlv-select

Enviar

30 Which command provides general neighbors information without details like Cisco IOS version and IP address?
Notas: --/1
Escolher uma resposta. a. show cdp neighbor
b. show interface
c. show cdp neighbor detail
d. show ip interface

Enviar

31 Which command should you enter to configure an LLDP delay time of 5 seconds?
Notas: --/1
Escolher uma resposta. a. lldp holdtime 5
b. lldp reinit 5
c. lldp reinit 5000
d. lldp timer 5000

Enviar

32 Which configuration ensures that the switch is always the root for VLAN 75?
Notas: --/1
Escolher uma resposta. a. Switch(config)#spanning-tree vlan 75 root primary
b. Switch(config)#spanning-tree vlan 75 priority 38003685
c. Switch(config)#spanning-tree vlan 75 priority 614440
d. Switch(config)#spanning-tree vlan 75 priority 0

Enviar

33 Which design element is a best practice when deploying an 802.11b wireless infrastructure?
Notas: --/1
Escolher uma resposta. a. allocating non overlapping channels to access points that are in close physical proximity to one anoth
b. disabling TPC so that access points can negotiate signal levels with their attached wireless devices
c. configuring access points to provide clients with a maximum of 5 Mbps
d. setting the maximum data rate to 54 Mbps on the Cisco Wireless LAN Controller

Enviar

34 Which mode allows access points to be managed by Cisco Wireless LAN Controllers?
Notas: --/1
Escolher uma resposta. a. mobility express
b. lightweight
c. bridge
d. autonomous

Enviar

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 6/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

35 Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?
Notas: --/1
Escolher uma resposta. a. active
b. on
c. auto
d. desirable

Enviar

36 Which mode must be used to configure EtherChannel between two switches using LACP as trunk negotiation protocol?
Notas: --/1
Escolher uma resposta. a. desirable
b. auto
c. on
d. active

Enviar

37 Which QoS Profile is selected in the GUI when configuring a voice over WLAN deployment?
Notas: --/1
Escolher uma resposta. a. Platinum
b. Gold
c. Bronze
d. Silver

Enviar

38 Which result occurs when PortFast is enabled on an interface that is connected to another switch?
Notas: --/1
Escolher uma resposta. a. Spanning tree may fail to detect a switching loop in the network that causes broadcast storms
b. After spanning tree converges PortFast shuts down any port that receives BPDUs
c. Root port choice and spanning tree recalculation are accelerated when a switch link goes down
d. VTP is allowed to propagate VLAN configuration information from switch to switch automatically

Enviar

39 Which state does the switch port move to when PortFast is enabled?
Notas: --/1
Escolher uma resposta. a. forwarding
b. blocking
c. learning
d. listening

Enviar

40 Which statement about Cisco Discovery Protocol is true?

Notas: --/1
Escolher uma resposta. a. It is a Cisco-proprietary protocol
b. It can discover information from routers, firewalls, and switches
c. It runs on the physical layer and the data link layer
d. It runs on the network layer

Enviar

41 Which statement about Link Aggregation when implemented on a Cisco Wireless LAN Controller is true?
Notas: --/1

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 7/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

Escolher uma resposta. a. The EtherChannel must be configured in “mode active”

b. When enabled the WLC bandwidth drops to 500 Mbps
c. To pass client traffic two or more ports must be configured
d. One functional physical port is needed to pass client traffic

Enviar

42 Which statement about VLAN configuration is true?

Notas: --/1
Escolher uma resposta. a. A switch in VTP transparent mode save the VLAN databases to the running configuration only
b. The switch must be in VTP server or transparent mode before you can configure a VLAN
c. The switch must be in config-vlan mode before you configure an extended VLAN
d. Dynamic inter-VLAN routing is supported on VLAN2 through VLAN 4064

Enviar

43 Which switch will be elected as the root bridge in a full-meshed topology with four switches? MAC addresses of the switches:
Notas: --/1
SW1: 0C:E0:38:00:36:75
SW2: 0C:0E:15:22:05:97
SW3: 0C:0E:15:1A:3C:9D
SW4: 0C:E0:18:A1:B3:19

Escolher uma resposta. a. SW2

b. SW4
c. SW1
d. SW3

Enviar

44 Which three statements are typical characteristics of VLAN arrangements? (Choose three.)
Notas: --/1
Escolha pelo menos a. VLANs cannot span multiple switches
uma resposta. b. Connectivity between VLANs requires a Layer 3 device
c. VLANs typically decrease the number of collision domains
d. A switch maintains a separate bridging table for each VLAN
e. Each VLAN uses a separate address space
f. A new switch has no VLANs configured

Enviar

45 Which two command sequences must you configure on a switch to establish a Layer 3 EtherChannel with an open-standard protocol?
Notas: --/1
Escolha pelo menos a. no switchport
uma resposta. b. channel-group 10 mode auto
c. switchport mode trunk
d. channel-group 10 mode active
e. channel-group 10 mode on

Enviar

46 Which two commands can be used to create port channel 10 using LACP as trunk negotiation protocol? (Choose two )
Notas: --/1
Escolha pelo menos a. channel-group 10 mode auto
uma resposta. b. channel-group 10 mode active
c. channel-group 10 mode on
d. channel-group 10 mode passive

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 8/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions
Enviar

47 Which two commands can you use to configure an actively negotiate EtherChannel? (Choose two)
Notas: --/1
Escolha pelo menos a. channel-group 10 mode auto
uma resposta. b. channel-group 10 mode on
c. channel-group 10 mode active
d. channel-group 10 mode passive
e. channel-group 10 mode desirable

Enviar

48 Which two pieces of information about a Cisco device can Cisco Discovery Protocol communicate? (Choose two.)
Notas: --/1
Escolha pelo menos a. the VTP domain
uma resposta.
b. the native VLAN
c. the spanning tree protocol
d. the trunking protocol
e. the spanning-tree priority

Enviar

49 Which two statements about EtherChannel technology are true? (Choose two)
Notas: --/1
Escolha pelo menos a. EtherChannel provides increased bandwidth by bundling existing FastEthernet or Gigabit Ethernet in
uma resposta. EtherChannel
b. You can configure multiple EtherChannel links between two switches, using up to a limit of sixteen ph
c. STP does not block EtherChannel links
d. EtherChannel does not allow load sharing of traffic among the physical links within the EtherChannel
e. EtherChannel allows redundancy in case one or more links in the EtherChannel fail

Enviar

50 Which two statements about VTP are true? (Choose two.)

Notas: --/1
Escolha pelo menos a. All switches must be configured with the same VTP domain name
uma resposta. b. All switches must be configured with a unique VTP domain name
c. The VTP server must have the highest revision number in the domain
d. All switches must use the same VTP version
e. All switches must be configured to perform trunk negotiation

Enviar

51 Which two values or settings must be entered when configuring a new WLAN in the Cisco Wireless LAN Controller GUI? (Choose two)
Notas: --/1
Escolha pelo menos a. SSID
uma resposta. b. ip address of one or more access points
c. Profile name
d. QoS settings
e. management interface settings

Enviar

52 Which two VLAN IDs indicate a default VLAN? (Choose two.)

Notas: --/1

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 9/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

Escolha pelo menos a. 1

uma resposta. b. 0
c. 1006
d. 4096
e. 1005

Enviar

53 Which type does a port become when it receives the best BPDU on a bridge?
Notas: --/1
Escolher uma resposta. a. The root port
b. The alternate port
c. The backup port
d. The designated port

Enviar

54 Which unified access point mode continues to serve wireless clients after losing connectivity to the Cisco Wireless LAN Controller?
Notas: --/1
Escolher uma resposta. a. local
b. mesh
c. sniffer
d. flex connect

Enviar

55 Which value can you modify to configure a specific interface as the preferred forwarding interface?
Notas: --/1
Escolher uma resposta. a. The hello time
b. The interface number
c. The VLAN priority
d. The port priority

Enviar

56 Which VLAN ID is associated with the default VLAN given the configuration below?
Notas: --/1
interface FastEthernet 0/1
switchport mode access
switchport access vlan 5
switchport voice vlan 20
!
interface FastEthernet 0/2
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk native vlan 10

Escolher uma resposta. a. VLAN 5

b. VLAN 1
c. VLAN 20
d. VLAN 10

Enviar

57 You have four switches in your LAN with the following MAC Address:
Notas: --/1
SW1: 0C:0E:15:AA:BB:CC
SW2: 0C:0E:15:AA:AA:BB
SW3: 0C:0E:15:1A:3C:9D e

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 10/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions
SW4: 0C:0E:15:A1:B3:19

Which switch in this configuration becomes the root bridge?

Escolher uma resposta. a. SW2

b. SW3
c. SW4
d. SW1

Enviar

58 Choose the benefits of a Cisco Wireless LAN Controller from the left onto the correct
Notas: --/1
examples on the right.

Easy upgrade process Escolher...

Dynamic RF Feature Escolher...

Optimized user performance Escolher...

Easy Deployment Process Escolher...

Enviar

59 Choose the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.
Notas: --/1
web policy Escolher...

WPA+WPA2 Escolher...

802.1X Escolher...

Passthrough Escolher...

Enviar

60 Choose the WLAN components from the left onto the correct descriptions on the right.
Notas: --/1
access point Escolher...

service port Escolher...

virtual interface Escolher...

dynamic interface Escolher...

wireless LAN controller Escolher...

Enviar

61 How does SW1 interact with other switches in this VTP domain?
Notas: --/1

Escolher uma resposta. a. It forwards only the VTP advertisements that it receives on its trunk ports.
b. It processes VTP updates from any VTP clients on the network on its access ports.
c. It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 11/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions
d. It transmits and processes VTP updates from any VTP Clients on the network on its trunk ports.

Enviar

62 Which action do the switches take on the trunk link?

Notas: --/1

Escolher uma resposta. a. The trunk does not form, but VLAN 99 and VLAN 999 are allowed to traverse the link.
b. The trunk forms but the mismatched native VLANs are merged into a single broadcast domain.
c. The trunk forms but VLAN 99 and VLAN 999 are in a shutdown state.
d. The trunk does not form and the ports go into an err-disabled status.

Enviar

63 Based on the LACP neighbor status, in which mode is the SW1 port channel configured?
Notas: --/1

Escolher uma resposta. a. mode on

b. auto
c. active
d. passive

Enviar

64 Which command provides this output?

Notas: --/1

Escolher uma resposta. a. show ip interface

b. show interface
c. show cdp neighbor
d. show ip route

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 12/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

Enviar

65 Which command provides this output?

Notas: --/1

Escolher uma resposta. a. show cdp

b. show lldp neighbor
c. show lldp
d. show cdp neighbor

Enviar

66 After the switch configuration the ping test fails between Linux host and VPC host. Based on the output which error must be corrected?
Notas: --/1

Escolher uma resposta. a. All VLANs are not enabled on the trunk
b. Access mode is configured on the switch ports
c. There is a native VLAN mismatch
d. The PCs are in the incorrect VLAN

Enviar

67 A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 999. What causes this behavior?
Notas: --/1

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 13/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

Escolher uma resposta. a. allowing only VLAN 999 on the destination

b. VLANs that do not correspond to a unique IP subnet
c. trunk mode mismatches
d. native VLAN mismatches

Enviar

68 What two conclusions should be made about this configuration? (Choose two )
Notas: --/1

Escolha pelo menos a. The designated port is FastEthernet 2/1

uma resposta. b. The spanning-tree mode is Rapid PVST+
c. This is a root bridge
d. The root port is FastEthernet 2/1
e. The spanning-tree mode is PVST+

Enviar

69 A network administrator assumes a task to complete the connectivity between PC A and the File Server Switch A and Switch B have b
Notas: --/1
with VLANs 10, 11, 12, and 13 What is the next step in the configuration?

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 14/15
02/04/2021 ccna-200-301: 2.0 Network Access Questions

Escolher uma resposta. a. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation
b. Add PC-A to VLAN 10 and the File Server to VLAN 11 for VLAN segmentation
c. Add a router on a stick between Switch A and Switch B allowing for Inter VLAN routing
d. Add PC-A to the same subnet as the File Server allowing for intra-VLAN communication

Enviar

70 An engineer needs to configure LLDP to send the port description time length value (TLV). What command sequence must be impleme
Notas: --/1
Escolher uma resposta. a. switch(config-line)#lldp tlv-select port-description
b. switch(config-if)#lldp tlv-select port-description
c. switch#lldp tlv-select port-description
d. switch(config)#lldp tlv-select port-description

Enviar

71 A wireless administrator has configured a WLAN; however, the clients need access to a less congested 5-GHz network for their voice q
Notas: --/1
be taken to meet the requirement?

Escolher uma resposta. a. enable DTIM

b. enable AAA override
c. enable Band Select
d. enable RX-SOP

Enviar

Salvar sem enviar Enviar página Enviar tudo e terminar

DlteC do Brasil Você acessou como M

www.dltec.com.br

www.dltec.com.br/class/mod/quiz/attempt.php?id=4223 15/15