AP7365

600mA, LOW QUIESCENT CURRENT

FAST TRANSIENT LOW DROPOUT LINEAR REGULATOR

Description Pin Assignments

The AP7365 is a 600mA, adjustable and fixed output voltage, low
(Top View) (Top View )
dropout linear regulator. This device includes pass element, error
amplifier, band-gap, current limit and thermal shutdown circuitry. The IN 1 5 OUT IN 1 5 OUT
device is turned on when EN pin is set to logic high level.
GND 2 GND 2
The characteristics of low dropout voltage and low quiescent current
EN 3 4 NC EN 3 4 ADJ
make it suitable for low power applications such as battery powered
devices. The typical quiescent current is approximately 35μA. Built-in
SOT25 (Fixed Output) SOT25 (ADJ Output)
current-limit and thermal-shutdown functions prevent IC from damage
(W Package) (W Package)
in fault conditions.

(Top View) (Top View)

This device is available with adjustable output from 0.8V to 5.0V, and
fixed version with 0.8V, 1.0V, 1.2V, 1.5V, 1.8V, 2.0V, 2.5V, 2.8V,
EN 1 6 NC EN 1 6 ADJ
3.0V, 3.3V and 3.9V outputs. Please contact your local sales office for
other voltage options. GND 2 5 NC GND 2 5 NC

The AP7365 is available in SOT25, SOT89, SOT223, and U- IN 3 4 OUT IN 3 4 OUT

DFN2020-6 packages.
U-DFN2020-6 (Fixed Output) U-DFN2020-6 (ADJ Output)
Features (SN Package) (SN Package)

 600mA Low Dropout Regulator with EN

 Very low IQ: 35µA (Top View) (Top View)
 Wide Input Voltage Range: 2V to 6V 3 IN 3 OUT
 Wide Adjustable Output: 0.8V to 5.0V
 Fixed Output Options: 0.8V to 3.9V (0.1V Step Size Possible) 2 GND (TAB) 2 IN (TAB)
 High PSRR: 65dB at 1kHz
1 OUT 1 GND
 Fast Start-Up Time: 200µs
 Stable with Low ESR, 1µF Ceramic Output Capacitor SOT89 (Fixed output) SOT89 (Fixed output)
 Excellent Load/Line Transient Response (Y Package) (YR Package)
 Low Dropout: 300mV at 600mA
 Current Limit and Short Circuit Protection (Top View) (Top View)
 Thermal Shutdown Protection
3 IN 3 OUT
 Ambient Temperature Range: -40°C to +85°C
 Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) 2 GND (TAB) 2 IN (TAB)
 Halogen and Antimony Free. “Green” Device (Note 3)
1 OUT 1 GND
Applications SOT223 (Fixed output) SOT223 (Fixed output)
 Servers and Notebook Computers (E Package) (ER Package)
 Low and Medium Power Applications
 FPGA and DSP Core or I/O Power (Top View)
 Consumer Electronics
3 IN

2 OUT (TAB)

1 GND

SOT223 (Fixed output)

(EV Package)

Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.

AP7365 1 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Typical Applications Circuit

VIN VOUT VIN VOUT
IN OUT IN OUT

AP7365 R1 AP7365
1μF 1μF 1μF 1μF
Enable Enable
EN ADJ EN

GND GND
R2

Adjustable Output Fixed Output

 R 
VOUT  VREF 1  1  where R2  80K
 R 2

Pin Descriptions
Pin Number
SOT89 SOT89
Pin
SOT25 SOT25 U-DFN2020-6 U-DFN2020-6 (Y Package) (YR Package) SOT223 Functions
Name
(Fixed) (ADJ) (Fixed) (ADJ) SOT223 SOT223 (EV Package)
(E Package) (ER Package)
Voltage Input Pin. Bypass to
IN 1 1 3 3 3 2 3 ground through at least 1µF MLCC
capacitor
GND 2 2 2 2 2 1 1 Ground
EN 3 3 1 1 — — — Enable Input, Active High
ADJ — 4 — 6 — — — Output Feedback Pin
NC 4 — 5, 6 5 — — — No Connection
Voltage Output Pin. Bypass to
OUT 5 5 4 4 1 3 2 ground through 1µF MLCC
capacitor

Functional Block Diagram

IN OUT IN OUT

Current Limit Current Limit

Gate Gate
EN and Thermal EN Driver
and Thermal
Driver Shutdown
Shutdown R

ADJ

0.8V 0.8V

GND GND

Adjustable Version
Fixed Version

AP7365 2 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.)

Symbol Parameter Ratings Unit
ESD HBM Human Body Model ESD Protection 2000 V
ESD MM Machine Model ESD Protection 200 V
VIN Input Voltage 6.5 V
 OUT, EN Voltage VIN +0.3 V
 Continuous Load Current per Channel Internal Limited 
TST Storage Temperature Range -65 to +150 °C
TJ Maximum Junction Temperature +150 °C

Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)

Symbol Parameter Min Max Unit
VIN Input Voltage 2 6 V
IOUT Output Current (Note 4) 0 600 mA
TA Operating Ambient Temperature -40 +85 °C
Note: 4. The device maintains a stable, regulated output voltage without a load current.

Electrical Characteristics (@TA = +25°C, VIN = VOUT +1V, COUT = 1μF, CIN = 1μF, VEN = 2V, unless otherwise specified.)

Symbol Parameter Test Conditions Min Typ Max Unit

VREF ADJ Reference Voltage (Adjustable Version) IOUT = 0mA — 0.8 — V
IADJ ADJ Leakage (Adjustable Version) — — 0.1 1.0 μA
TA = -40°C to +85°C,
VOUT Output Voltage Accuracy -2 — +2 %
IOUT = 10% of IOUT-Max
VOUT VIN = (VOUT +1V) to VIN-Max,
Line Regulation — 0.02 0.20 %/V
/VIN/V VEN = VIN, IOUT = 1mA
VIN = (VOUT +1V) to VIN-Max,
VOUT/VOUT Load Regulation -1.0 — +1.0 %
IOUT = 1mA to 600mA
VOUT < 2.5V, IOUT = 600mA — 370 600
VDROPOUT Dropout Voltage (Note 5) mV
VOUT ≥ 2.5V, IOUT = 600mA — 300 400
IQ Input Quiescent Current VEN = VIN, IOUT = 0mA — 35 80 μA
ISHDN Input Shutdown Current VEN = 0V, IOUT = 0mA — 0.1 1.0 μA
ILEAK Input Leakage Current VEN = 0V, OUT grounded — 0.1 1.0 μA
VEN = 0V to 2.0V in 1μs,
tST Start-Up Time — 200 — μs
IOUT = 600mA
VIN = [VOUT +1V] VDC + 0.5VppAC,
PSRR PSRR (Note 6) — 65 — dB
f = 1kHz, IOUT = 50mA
VIN = VIN-Min to VIN-Max,
ISHORT Short-Circuit Current VOUT < 0.2V (fixed version) or 25% of — 240 — mA
VOUT (ADJ version)
VIN = VIN-Min to VIN-Max,
ILIMIT Current limit 0.8 1.4 — A
VOUT/ROUT = 2.5A
VIL EN Input Logic Low Voltage VIN = VIN-Min to VIN-Max — — 0.4 V
VIH EN Input Logic High Voltage VIN = VIN-Min to VIN-Max 1.4 — — V
IEN EN Input Current VIN = 0V or VIN-Max -1 — +1 μA
TSHDN Thermal Shutdown Threshold — — +145 — °C
THYS Thermal Shutdown Hysteresis — — +15 — °C
Notes: 5. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value. This
parameter only applies to input voltages above minimum VIN = 2.0V.
6. At VIN < 2.3V, the PSRR performance may be reduced.

AP7365 3 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Electrical Characteristics (Cont.) (@TA = +25°C, VIN = VOUT +1V, COUT = 1μF, CIN = 1μF, VEN = 2V, unless otherwise specified.)

Symbol Parameter Test Conditions Min Typ Max Unit

SOT25 (Note 7) — 169 —
U-DFN2020-6 (Note 7) — 132 —
JA Thermal Resistance Junction-to-Ambient °C/W
SOT89 (Note 7) — 133 —
SOT223 (Note 7) — 142 —
SOT25 (Note 7) — 31 —
U-DFN2020-6 (Note 7) — 48 —
JC Thermal Resistance Junction-to-Case °C/W
SOT89 (Note 7) — 30 —
SOT223 (Note 7) — 39 —
Note: 7. Test condition for all packages: Device mounted on FR-4 substrate PC board, 1oz copper, with minimum recommended pad layout.

Typical Performance Characteristics

VEN = 0 to 2V (1V/div) VEN = 0 to 2V (1V/div)

VIN = 5V VIN = 5V
CIN = COUT = 1μF CIN = COUT = 1μF

VOUT = 3.3V (1V/div) VOUT = 3.3V (1V/div)

with no load with 600mA load

Time (40μs/div) Time (40μs/div)

Start-Up Time Start-Up Time

VIN = 4.3V to 5.3V (1V/div) VIN = 4.3V to 5.3V (1V/div)

tR = tF = 2μs tR = tF = 2μs
CIN = none, COUT = 1μF CIN = none, COUT = 1μF

VOUT = 3.3V (20mV/div) VOUT = 3.3V (20mV/div)

IOUT = 300mA (200mA/div)

IOUT = 60mA (200mA/div)

Time (40μs/div) Time (40μs/div)

Line Transient Response Line Transient Response

AP7365 4 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Typical Performance Characteristics (Cont.)

VOUT = 1.8V (200mV/div) VOUT = 1.8V (200mV/div)

VIN = VEN = 2.8V VIN = VEN = 2.8V

CIN = COUT = 1μF CIN = COUT = 1μF
tR = tF = 1μs tR = tF = 1μs

IOUT = 10mA to 600mA (500mA/div)

IOUT = 10mA to 300mA (500mA/div)

Load Transient Response Load Transient Response

Time (100μs/div) Time (100μs/div)

VOUT = 3.3V (200mV/div) VOUT = 3.3V (200mV/div)

VIN = VEN = 4.3V VIN = VEN = 4.3V

CIN = COUT = 1μF CIN = COUT = 1μF
tR = tF = 1μs tR = tF = 1μs

IOUT = 10mA to 600mA (500mA/div)

IOUT = 10mA to 300mA (500mA/div)

Load Transient Response Load Transient Response

Time (100μs/div) Time (100μs/div)

AP7365 5 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Typical Performance Characteristics (Cont.)

80 80
IOUT = 50mA IOUT = 50mA
70 70

60 60
IOUT =300mA
IOUT =300mA
)B 50 )B 50
PSRR (dB)

PSRR (dB)
d d
( (
R 40 R 40
R R
S S
P P 30
30

20 20 VIN = 2.25V +0.5V ppAC

VIN = 2.25V +0.5VppAC
VOUT = 0.8V VOUT = 1.2V
10 CIN = none, COUT = 1µF 10 CIN = none, COUT = 1µF
TA= +25°C TA = +25°C
0 0
0.1 1.0 10.0 100.0 0.1 1.0 10.0 100.0
FREQUENCY (kHz) FREQUENCY (kHz)
PSRR PSRR

80 80
IOUT = 50mA IOUT = 50mA

70 70

60 60
IOUT = 300mA
50 50
PSRR (dB)
PSRR (dB)

)B )B
d d IOUT = 300mA
( ( 40
R 40 R
R R
S S
P 30 P 30

20 VIN = 2.8V +0.5VppAC 20 VIN = 4.3V +0.5VppAC

VOUT = 1.8V VOUT = 3.3V
10 CIN = none, COUT = 1µF 10 CIN = none, COUT = 1µF
TA = +25°C TA = +25°C
0 0
0.1 1.0 10.0 100.0 0.1 1.0 10.0 100.0
FREQUENCY (kHz) FREQUENCY (kHz)
PSRR PSRR

60 60
TTAA = 25癈
25°C VIN = VEN = 4.3V
VVOUT
OUT == 3.3V
INPUT QUIESCENT CURRENT (µA)
INPUT QUIESCENT CURRENT (µA)

3.3V VOUT = 3.3V

IOUT = 0mA 50
50 IOUT = 0mA IOUT = 0mA

40 40

30 30

20 20

10 10

0 0
4.0 4.5 5.0 5.5 6.0 -50 -25 0 25 50 75 100 125
INPUT VOLTAGE (V) TEMPERATURE (° (癈C))
Input Quiescent Current vs. Input Voltage Input Quiescent Current vs. Temperature

AP7365 6 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Typical Performance Characteristics (Cont.)

0.1 0.08
-45°C VOUT = 3.3V
IOUT = 1mA +90°C
0.0
-45°C

OUTPUT VARIATION (%)

)
% )% 0.04
OUTPUT VARIATION (%)

( (
N -0.1 N
O +25°C O
IT TI
A +90°C
A
IR RI
A -0.2 A 0.00
V V
T T
U U
P -0.3 P
T T +25°C
U U
O O -0.04
VIN = VEN = 4.3V
-0.4
VOUT = 3.3V

-0.5 -0.08
0 100 200 300 400 500 600 4.0 4.5 5.0 5.5 6.0
OUTPUT CURRENT (mA) INPUT VOLTAGE (V)
Load Regulation Line Regulation

600 500
VOUT = 1.8V
VOUT = 3.3V

500
DROPOUT VOLTAGE (mV)

)V 400
DROPOUT VOLTAGE (mV)
)V +90°C
m m +90°C
( +25°C (
E 400 E +25°C
G G
A A 300
T T
L L
O 300 O
V V
T T
U U 200
O O
P 200 P
O O -45°C
R R
D D
-45°C 100
100

0 0
0 100 200 300 400 500 600 0 100 200 300 400 500 600
OUTPUT CURRENT (mA) OUTPUT CURRENT (mA)
Dropout Voltage vs. Output Current Dropout Voltage vs. Output Current

500
ADJ Reference Voltage vs Temperature VIN = 4.3V
SHORT CIRCUIT CURRENT (mA)

0.82
400
ADJ Reference Voltage(V)

0.81
300

0.80
200

0.79
100

0.78
0
-50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125
Temperature(℃) TEMPERATURE (° (癈
C))
Short Circuit Current vs. Temperature

AP7365 7 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Typical Performance Characteristics (Cont.)

2.0

1.6
CURRENT LIMIT (A)

1.2

0.8

0.4
VIN = 4.3V
VOUT = 3.3V

0.0
-50 -25 0 25 50 75 100 125
TEMPERATURE (° (癈
C))
Current Limit vs. Temperature

Application Information
Input Capacitor
A 1µF ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and noise. The amount of the
capacitance may be increased without limit. This input capacitor must be located as close as possible to the device to assure input stability and
reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins. A lower ESR capacitor type allows the use of less
capacitance, while higher ESR type requires more capacitance.

Output Capacitor
The output capacitor is required to stabilize and improve the transient response of the LDO. The AP7365 is stable with very small ceramic output
capacitors. Using a ceramic capacitor value that is at least 1μF with ESR > 15mΩ on the output ensures stability. Higher capacitance values help
to improve line and load transient response. The output capacitance may be increased to keep low undershoot and overshoot. Output capacitor
must be placed as close as possible to OUT and GND pins.

100

Unstable Range
10

Unstable Range
COUT ESR ()

1
VVININ == 4.3V
4.3V
Stable Range CCININ == C
COUT = =1µF
OUT 1礔
0.1

0.01 Stable Range

Unstable Range

0.001
0 100 200 300 400 500 600
LOAD CURRENT (mA)
Region of Stable COUT ESR vs. Load Current

AP7365 8 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Application Information (Cont.)

Adjustable Operation
The AP7365 provides output voltage from 0.8V to 5.0V through external resistor divider as shown below.

VIN VOUT
IN OUT

AP7365 R1
1μF 1μF
Enable
EN ADJ

GND
R2

The output voltage is calculated by:

 R 
VOUT  VREF 1  1 
 R 2

Where VREF = 0.8V (the internal reference voltage)

Rearranging the equation will give the following that is used for adjusting the output to a particular voltage:

V 
R1  R2  OUT  1
 REF
V 

To maintain the stability of the internal reference voltage, R2 needs to be kept smaller than 80kΩ.

No Load Stability
Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and regulated in no load
condition.

ON/OFF Input Operation

The AP7365 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to IN pin
to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above
and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under V IL and VIH.

Current Limit Protection

When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to
approximately 1.4A to prevent overcurrent and to protect the regulator from damage due to overheating.

Short Circuit Protection

When OUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 240mA. This feature
protects the regulator from overcurrent and damage due to overheating.

Thermal Shutdown Protection

Thermal protection disables the output when the junction temperature rises to approximately +145°C, allowing the device to cool down. When the
junction temperature reduces to approximately +130°C, the output circuitry is enabled again. Depending on power dissipation, thermal resistance
and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it
from damage due to overheating.

Ultra Fast Start-Up

After enabled, the AP7365 is able to provide full power in as little as hundreds of microseconds, typically 200µs, without sacrificing low ground
current. This feature will help load circuitry move in and out of standby mode in real time, eventually extend battery life for mobile phones and
other portable devices.

AP7365 9 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Application Information (Cont.)

Fast Transient Response
Fast transient response LDO can extend battery life. TDMA-based cell phone protocols such as Global System for Mobile Communications (GSM)
have a transmit/receive duty factor of only 12.5%, enabling power savings by putting much of the baseband circuitry into standby mode in between
transmit cycles. In baseband circuits, the load often transitions virtually instantaneously from 100µA to 100mA. To meet this load requirement, the
LDO must react very quickly without a large voltage drop or overshoot — a requirement that cannot be met with conventional, general-purpose
LDO.

The AP7365’s fast transient response from 0 to 600mA provides stable voltage supply for fast DSP and GSM chipset with fast changing load.

Low Quiescent Current

The AP7365, consuming only around 35µA for all input ranges, provides great power saving in portable and low power applications.

Wide Output Range

The AP7365, with a wide output range of 0.8V to 5.0V, provides a versatile LDO solution for many portable applications.

Power Dissipation
The device power dissipation and proper sizing of the thermal plane connected to the thermal pad is critical to avoid thermal shutdown and ensure
reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by:

PD = (VIN - VOUT) X IOUT

The maximum power dissipation, handled by the device, depends on the maximum junction to ambient thermal resistance, maximum ambient
temperature, and maximum device junction temperature, which can be calculated by the equation in the following:

( 145 C - TA )
PD (MAX @ T A ) 
R JA

Ordering Information
AP7365 - XX XX G - X

Output Package Green Packing

Blank : ADJ (Note 8) W : SOT25 G : Green 7/13 : Tape & Reel
08 : 0.8V SN : U-DFN2020-6
10 : 1.0V Y/YR : SOT89
12 : 1.2V E/ER/EV : SOT223
15 : 1.5V
18 : 1.8V
20 : 2.0V
25 : 2.5V
28 : 2.8V
30 : 3.0V
33 : 3.3V
39 : 3.9V

7”/13” Tape and Reel

Part Number Package Code Packaging
Quantity Part Number Suffix
AP7365-XXWG-7 W SOT25 3,000/Tape & Reel -7
AP7365-XXSNG-7 SN U-DFN2020-6 3,000/Tape & Reel -7
AP7365-XXYG-13 Y SOT89 2,500/Tape & Reel -13
AP7365-XXYRG-13 YR SOT89 2,500/Tape & Reel -13
AP7365-XXEG-13 E SOT223 2,500/Tape & Reel -13
AP7365-XXERG-13 ER SOT223 2,500/Tape & Reel -13
AP7365-XXEVG-13 EV SOT223 2,500/Tape & Reel -13
Note: 8. Adjustable version is only available in SOT25 and U-DFN2020-6 packages.

AP7365 10 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Marking Information
(1) SOT25
( Top View )
5 4

7
XX : Identification code
Y : Year 0~9
XX Y W X W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
1 2 3 X : A~Z : Green

Part Number Package Identification Code

AP7365-WG-7 SOT25 VA
AP7365-08WG-7 SOT25 VB
AP7365-10WG-7 SOT25 VC
AP7365-12WG-7 SOT25 VD
AP7365-15WG-7 SOT25 VE
AP7365-18WG-7 SOT25 VF
AP7365-20WG-7 SOT25 VG
AP7365-25WG-7 SOT25 VH
AP7365-28WG-7 SOT25 VJ
AP7365-30WG-7 SOT25 VK
AP7365-33WG-7 SOT25 VM
AP7365-39WG-7 SOT25 VN

(2) U-DFN2020-6
( Top View )
XX : Identification Code
XX Y : Year : 0~9
Y WX W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
Part Number Package Identification Code
AP7365-SNG-7 U-DFN2020-6 VA
AP7365-08SNG-7 U-DFN2020-6 VB
AP7365-10SNG-7 U-DFN2020-6 VC
AP7365-12SNG-7 U-DFN2020-6 VD
AP7365-15SNG-7 U-DFN2020-6 VE
AP7365-18SNG-7 U-DFN2020-6 VF
AP7365-20SNG-7 U-DFN2020-6 VG
AP7365-25SNG-7 U-DFN2020-6 VH
AP7365-28SNG-7 U-DFN2020-6 VJ
AP7365-30SNG-7 U-DFN2020-6 VK
AP7365-33SNG-7 U-DFN2020-6 VM
AP7365-39SNG-7 U-DFN2020-6 VN

AP7365 11 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Marking Information (Cont.)

(3) SOT89
( Top View )
XX : Identification code
XX Y : Year : 0~9
W : Week : A~Z : 1~26 week;
Y W X a~z : 27~52 week;
z represents 52 and 53 week
1 2 3 X : Internal code
A~Z : Green

Part Number Package Identification Code

AP7365-08YG-13 SOT89 VB
AP7365-10YG-13 SOT89 VC
AP7365-12YG-13 SOT89 VD
AP7365-15YG-13 SOT89 VE
AP7365-18YG-13 SOT89 VF
AP7365-20YG-13 SOT89 VG
AP7365-25YG-13 SOT89 VH
AP7365-28YG-13 SOT89 VJ
AP7365-30YG-13 SOT89 VK
AP7365-33YG-13 SOT89 VM
AP7365-39YG-13 SOT89 VN
AP7365-08YRG-13 SOT89 TB
AP7365-10YRG-13 SOT89 TC
AP7365-12YRG-13 SOT89 TD
AP7365-15YRG-13 SOT89 TE
AP7365-18YRG-13 SOT89 TF
AP7365-20YRG-13 SOT89 TG
AP7365-25YRG-13 SOT89 TH
AP7365-28YRG-13 SOT89 TJ
AP7365-30YRG-13 SOT89 TK
AP7365-33YRG-13 SOT89 TM
AP7365-39YRG-13 SOT89 TN

(4) SOT223 (E Package)

( Top View )

Y : Year : 0~9
Logo YWX W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
Part Number 6 5-VV z repersents 52 and 53 week
X : Internal code
65-VV:08 for 0.8V
A~Z : Green
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V

AP7365 12 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Marking Information (Cont.)

(5) SOT223 (ER Package)

( Top View )

Y : Year : 0~9
Logo YWX W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
Part Number 6 5 R -VV z repersents 52 and 53 week
X : Internal code
65R-VV : 08 for 0.8V
A~Z : Green
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V

(6) SOT223 (EV Package)

( Top View )

Y : Year : 0~9
Logo YWX W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
Part Number 6 5 V -VV z repersents 52 and 53 week
X : Internal code
65V-VV : 08 for 0.8V
A~Z : Green
10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
20 for 2.0V
25 for 2.5V
28 for 2.8V
30 for 3.0V
33 for 3.3V
39 for 3.9V

AP7365 13 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Package Outline Dimensions

Please see http://www.diodes.com/package-outlines.html for the latest version.

(1) Package Type: SOT25

A SOT25
Dim Min Max Typ
A 0.35 0.50 0.38
B C
B 1.50 1.70 1.60
C 2.70 3.00 2.80
D   0.95
H 2.90 3.10 3.00
J 0.013 0.10 0.05
H K 1.00 1.30 1.10
L 0.35 0.55 0.40
K
N M M 0.10 0.20 0.15
N 0.70 0.80 0.75
J  0° 8° 
D L
All Dimensions in mm

(2) Package Type: U-DFN2020-6

A1
A3

A
U-DFN2020-6
Seating Plane Dim Min Max Typ
A 0.57 0.63 0.60
D A1 0 0.05 0.03
D2
A3 - - 0.15
b 0.20 0.30 0.25
D2/2 D 1.95 2.075 2.00
D2 1.45 1.65 1.55
0
e - - 0.65
.10
R0 E 1.95 2.075 2.00
E2 0.76 0.96 0.86
E2/2 L 0.30 0.40 0.35
E E2 All Dimensions in mm
Pin #1 ID

e b

AP7365 14 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Package Outline Dimensions (Cont.)

Please see http://www.diodes.com/package-outlines.html for the latest version.

(3) Package Type: SOT89

D1
0
.20 c
R0
SOT89
Dim Min Max Typ
A 1.40 1.60 1.50
B 0.50 0.62 0.56
H B1 0.42 0.54 0.48
E
c 0.35 0.43 0.38
D 4.40 4.60 4.50
D1 1.62 1.83 1.733
D2 1.61 1.81 1.71
B1 L E 2.40 2.60 2.50
B E2 2.05 2.35 2.20
e - - 1.50
e H 3.95 4.25 4.10
D2 H1 2.63 2.93 2.78
L 0.90 1.20 1.05
L1 0.327 0.527 0.427
8°
(4 z 0.20 0.40 0.30
X)
All Dimensions in mm
H1
E2

L1

D z

(4) Package Type: SOT223

D
b1 Q
C
SOT223
Dim Min Max Typ
A 1.55 1.65 1.60
A1 0.010 0.15 0.05
b 0.60 0.80 0.70
b1 2.90 3.10 3.00
E E1
C 0.20 0.30 0.25
D 6.45 6.55 6.50
Gauge E 3.45 3.55 3.50
Plane E1 6.90 7.10 7.00
0.25 e - - 4.60
Seating
Plane
L e1 - - 2.30
L 0.85 1.05 0.95
e1 b 0° Q 0.84 0.94 0.89
-1
e 0° All Dimensions in mm

A A1 7°
7°

AP7365 15 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Suggested Pad Layout

Please see http://www.diodes.com/package-outlines.html for the latest version.

(1) Package Type: SOT25

Dimensions Value (in mm)

C2 C2
Z 3.20
G 1.60
X 0.55
G C1 Y 0.80
Z
C1 2.40
C2 0.95
Y

(2) Package Type: U-DFN2020-6

X
C

G
Y Value
Dimensions
(in mm)
C 0.65
G 0.15
X 0.37
Y1
X1 1.67
Y 0.45
Y1 0.90

X1

(3) Package Type: SOT89

X2
Value
Dimensions
(in mm)
C 1.500
G 0.244
Y3 X 0.580
Y1 X1 0.760
X2 1.933
Y4 X G Y 1.730
Y1 3.030
Y2 1.500
Y3 0.770
Y Y2 Y4 4.530

X1

AP7365 16 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

Suggested Pad Layout (Cont.)

Please see http://www.diodes.com/package-outlines.html for the latest version.

(4) Package Type: SOT223

X1

Y1
Dimensions Value (in mm)
C 2.30
C1 6.40
X 1.20
C1 Y2 X1 3.30
Y 1.60
Y1 1.60
Y2 8.00

X C

Tape Orientation (Note 9)

For U-DFN2020-6

Note: 9. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf.

AP7365 17 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
 AP7365

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.

This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2017, Diodes Incorporated

www.diodes.com

AP7365 18 of 18 October 2017

Document number: DS32260 Rev. 10 - 2 www.diodes.com © Diodes Incorporated
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Diodes Incorporated:
AP7365-08SNG-7 AP7365-08WG-7 AP7365-08YG-13 AP7365-08YRG-13 AP7365-10SNG-7 AP7365-10WG-7
AP7365-10YG-13 AP7365-10YRG-13 AP7365-12SNG-7 AP7365-12WG-7 AP7365-12YG-13 AP7365-12YRG-13
AP7365-15SNG-7 AP7365-15WG-7 AP7365-15YG-13 AP7365-15YRG-13 AP7365-18SNG-7 AP7365-18WG-7
AP7365-18YG-13 AP7365-18YRG-13 AP7365-20SNG-7 AP7365-20WG-7 AP7365-20YG-13 AP7365-20YRG-13
AP7365-25SNG-7 AP7365-25WG-7 AP7365-25YG-13 AP7365-25YRG-13 AP7365-28SNG-7 AP7365-28WG-7
AP7365-28YG-13 AP7365-28YRG-13 AP7365-30SNG-7 AP7365-30WG-7 AP7365-30YG-13 AP7365-30YRG-13
AP7365-33SNG-7 AP7365-33WG-7 AP7365-33YG-13 AP7365-33YRG-13 AP7365-39SNG-7 AP7365-39WG-7
AP7365-39YG-13 AP7365-39YRG-13 AP7365-SNG-7 AP7365-WG-7