Scribd
Upload
19 views

1226 Question Paper

Class 10th que paper

Uploaded by

ketoj74196
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
19 views

1226 Question Paper

Class 10th que paper

Uploaded by

ketoj74196
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Seat No: ______________ Enrollment No: ____________________

PARUL UNIVERSITY
FACULTY OF ENGINEERING & TECHNOLOGY
B.Tech Summer 2018 - 19 Examination
Semester: 6 Date: 09/05/2019
Subject Code: 03103381 Time: 10:30 am to 1:00 pm
Subject Name: Separation Techniques Total Marks: 60
Instructions:
1. All questions are compulsory.
2. Figures to the right indicate full marks.
3. Make suitable assumptions wherever necessary.
4. Start new question on new page.

Q.1 Objective Type Questions - (15)


1. The polymer is compressed between two heated plates under a pressure of 2000-5000 psi for 1-5
min in the process named-
a) Solution casting method
b) Melt extruded method
c) Track-etch method
d) Expanded film membranes
2. Polymer solution used for solution casting should be sufficiently _______ to prevent it from
running over the casting plate.
a) Dilute
b) Viscous
c) Cannot predict
d) a) and b) both
3. Pore size of microporous membrane is-
a) 1µm
b) 0.1 to 10 µm
c) < 0.1 µm
d) None
4. For in-line microfiltration-
a) Capital cost is high.
b) Operating cost is high.
c) Capital cost is low and operating cost is high.
d) Capital cost is high and operating cost is low.
5. The key property of membrane is to control-
a) Pore size
b) Permeate size
c) Permeation rate
d) All of the above
6. Reverse osmosis is a process where water is ________ by pushing it under pressure through a
semipermeable RO membrane.
7. Volume elements appear and disappear as motion of permeants traversing the membrane in
_____________(Name of model).
8. Examples of processes which used dense membranes are ___________ and __________
9. Separation of solutes by microporous membranes is mainly a function of___________
And ______________ .
10. Ultrafiltration will remove _____________ and _________________ .
11.Name the factors affecting retentity of membranes .
12. Thin polymer is irradiated by nuclear fission particles in which type of method.
13.What is the basic governing equation in Pore flow model.
14.Due to high cost, plate and frame module is replaced by which modules.
15. Ceramic, metal and liquid membranes comes under which type of classification of membranes
Q.2 Answer the following questions. (Attempt any three) (15)
A) Explain principle types of microfiltration membrane filters also mention the flow processes.
B) Explain Extractive distillation method with example and diagram.
C) Explain concentration and pressure gradient in the membrane and write the equation for
chemical potential for compressible and incompressible phases.
D) Explain the Reverse Osmosis along with principle, working and application.
Q.3 A) Explain Azeotropic distillation method along with different types of azeotropes formed during (07)
Page 1 of 2
process. Explain distillation process with example and diagram.
B) Explain Steam distillation method with example and diagram. (08)
OR
B) Explain Reactive distillation method with example and diagram. (08)
Q.4 A) Explain Supercritical fluid extraction method with example and diagram. (07)
OR
A) Why CO2 is chosen as supercritical fluid? Name some commonly used supercritical solvents. (07)
Name some of the important parameter for SCF extraction.
B) Explain 4 types of precipitation method under Phase Separation Membrane. (08)

Page 2 of 2

You might also like