CADANGAN TAMBAHAN DAN UBAHSUAI

BAGI SEBUAH PUSAT JAGAAN

AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 1 of 9

METHOD STATEMENT FOR

EXTERNAL PAINTING

Issue No.: 0
Revision No.: 0
 CADANGAN TAMBAHAN DAN UBAHSUAI
BAGI SEBUAH PUSAT JAGAAN
AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 2 of 9

Revision Record

1. This cover page is a record of all revisions of the document identified above by number and title. All
previous cover pages are hereby superseded and are to be destroyed.

2. The contractor has the full right to modify, amend or change Method Statement and supporting
documents as required or as deemed necessary. All such documents will be submitted to the
“CONSULTANT” for approval.

Prepared Reviewed Approval for Description & page Number of

Rev Date
By by Issuance by Revision
00 14/07/2019 AFIQ FAISAL GLS SETIA

CONTENTS

Issue No.: 0
Revision No.: 0
 CADANGAN TAMBAHAN DAN UBAHSUAI
BAGI SEBUAH PUSAT JAGAAN
AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 3 of 9

1.0 SCOPE

2.0 PURPOSE

3.0 REFERENCES

4.0 DEFINITIONS AND ABBREVIATIONS

5.0 RESPONSIBILITIES

6.0 MATERIALS

7.0 EQUIPMENT & TOOLS

8.0 SAFETY & HEALTH

9.0 PROCEDURE

10.0 ATTACHMENTS

Issue No.: 0
Revision No.: 0
 CADANGAN TAMBAHAN DAN UBAHSUAI
BAGI SEBUAH PUSAT JAGAAN
AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 4 of 9

1.0 SCOPE
This method statement covers application of external stone painting as indicated in approved schedule of finishes as specified in specification for civil &
architectural works.
2.0 PURPOSE
The purpose of generating this method statement is to describe the procedure for application of stone painting as specified in Specification
3.0 REFERENCES

 Project Specifications

 Schedule of Finishes

Stone Finish Paint


Approved supplier details

Project Quality Plan

Project HSE Plan

4.0 DEFINITIONS& ABBREVIATIONS
PM: Project Manager

CM: Construction Manager

PE: Project Engineer

QCE: Quality Control Engineer

QA QC: Quality Assurance and quality Control

PPE: Personal Protective Equipment

HSE: Health, Safety and Environment

5.0 RESPONSIBILITIES

 Project Manager is responsible for overall project execution, quality and safety. Adopt a leading role with respect to Contractor’s quality and safety
procedures. The PM is responsible for the overall implementation of this method statement. The Project Manager shall ensure that the key personnel
are well aware of the specifications and method statement.

 CM / Project Engineer shall arrange all materials, equipment, safety related items & manpower & direct the Site Engineers & Foremen to resort
appropriate action for the smooth execution of the works.

 Safety Engineer shall be responsible for safe working environment & conditions. Coordinate with Site Engineer to identify potential hazards before
works and advise methods of safe working from new developments.

 Surveyor shall be responsible for setting out for levels, layout, and lines & establish top levels. Ensuring setting out books are properly maintained and
filed when completed. To coordinate with the CONSULTANT surveyor in determining coordinates, levels, and limits.

 QA/QC Engineer shall be responsible for ensuring that execution of works are complying with approved method statement; specifications, approved
shop drawings and ensure ITR are submitted based on ITP requirements.

Issue No.: 0
Revision No.: 0
 CADANGAN TAMBAHAN DAN UBAHSUAI
BAGI SEBUAH PUSAT JAGAAN
AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 5 of 9

 Site Engineer shall ensure that all works are carried out according to approved shop drawings. He shall direct the surveyor for the setting out lines &
levels in concurrence from the Construction Manager/Senior Civil Engineer.

 MEP Coordinator / Engineer shall be responsible for proper execution of MEP works involved before, during and after the works.
6.0 MATERIALS

As per the approved material submittal.


7.0 EQUIPMENTS & TOOLS

Spray Gun

Masks

Painting Rollers

Painting Brush

Putty knifes

Scrappers

Abrasive Paper

Bucket

Ladders

Mobile scaffolds


The capacity / size of the above tools and equipment shall be judged in accordance with site
conditions, requirements, and availability at the time of execution

8.0 SAFETY & HEALTH

 All employees shall be provided with complete personal Protection equipment PPE.

 All employees shall attend Safety Induction and training Course to identify all Hazards associated with this work.

 All workers shall be provided with proper tools and equipment to execute the work safely.

 MSDS (material safety data sheet) shall be displayed at work location as appropriate
9.0 PROCEDURE
GENERAL:

 Check materials, paint system and subcontractors are approved by the Engineer.

 Delivered paint materials shall be checked the following things:

Expiry date, original labeled containers, manufacturer's name, type of paint, brand name, color designation and instructions for mixing and/or
reducing.

Issue No.: 0
Revision No.: 0
 CADANGAN TAMBAHAN DAN UBAHSUAI
BAGI SEBUAH PUSAT JAGAAN
AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 6 of 9

 Material shall be stored in a cool, well ventilated and dry place, away from direct sunlight.

 Ensure necessary MEP clearance obtained from concerned departments.

 The parts not to be painted are protected prior to commence of painting works.

 Before commencement of work, remove electrical switch and outlet plates, surface hardware, frames of lighting fixtures and all the other obstructions
and replace properly at completion of the work.

 Mock Samples will be prepared in the designated area for the CONSULTANT approval using the correct material, number of coats, colour, texture and
degree of gloss required.

 The Surfaces to receive painting shall be free from all loose particles and prepared as per manufacturer's recommendation.

 Painting work shall not proceed in windy and rainy climate.

 Proper working platforms and lighting arrangement shall be provided.

 Scaffolding and working platform shall be checked against safety.

 All materials must be collected and returned to the designated storage area after working hours and properly secured and locked.
Preparation:

 Prior commencing, clean floors and adjacent surfaces, as well as surfaces to be painted.

 Surface shall be sound, clean, dry and free from all defective or poorly adhering materials, dirt, grease etc.

 Defects in the plastered surfaces will be repaired using approved patching compound or plaster and flush with adjoining surface, when dry, smooth and
seal the patch before application of priming coat.

 Cement plastered surfaces shall be rubbed down with rubbing stone or approved method and cleaned of dust and all foreign matter before application
of primer

 Fill any nail holes and similar defect after primer coat has been applied.

 In case of high alkali conditions, wash the surface to neutralize the alkali.

 Wire-brush concrete and masonry surfaces.

 In case area to be painted is having any existing coating, it should be cleaned, sanded and primed with the approved primer. All loose existing coating
should be removed prior to application of primer.

 Test all the surfaces for moisture before painting. Do not apply paint when moisture content exceeds 8%, as determined by an approved moisture
testing device.
Application:

 Do not undertake exterior painting at temperatures outsides of paint manufacturer’s recommended application and curing temperature and humidity
range, or immediately following rain and dew.

 Avoid painting surfaces when exposed to hot sun.

 thoroughly mix the materials before application as per manufacturer recommendations

 apply paint under adequate illumination

 Specific paint system shall be applied at locations as per approved finishes schedule.

 Paint application to be done as per manufacturer recommendations.

Please see attached “Application Method Statement for Eurostone” for the details of proposed system and application.
QUALITY CONTROL PROCEDURE

 Prior to start of works concerned CM and PE will verify the following.

o Approval of supplier / subcontractor by the CONSULTANT

Issue No.: 0
Revision No.: 0
 CADANGAN TAMBAHAN DAN UBAHSUAI
BAGI SEBUAH PUSAT JAGAAN
AMBULATORI SWASTA SETINGGI 4
TINGKAT DI ATAS LOT 3140, BANDAR
TAIPING DAERAH LARUT DAN MATANG,
PERAK DARUL RIDZUAN.

Document No:
GLSS-JP-MS-CS34
Rev : 00
Date: 14/07/2019
Method Statement for
External Painting
Page 7 of 9

o Approval of stone paint materials by the CONSULTANT

o Ensure necessary MEP clearance obtained from concerned departments.

 Paint system samples Mock ups of all types of finishes shall be made in presence of CONSULTANT’s representative as specified in the specification

 Samples shall be made using correct approved materials, number of coats, colour, texture and degree of gloss required as specified in the specification

Delivered paint materials shall be checked the following things:


Expiry date, original labeled containers, manufacturer's name, type of paint, brand name, color designation and instructions for mixing and/or reducing
as specified in Specification

 Approved paint materials delivered to site shall be stored at designated area as specified in the specification

 Substrate surface to receive shall be dry, clean sound, free from all defects and extraneous matter as specified in the specification

 Cement plastered surfaces rubbed down with rubbing stone shall be cleaned of dust and all foreign matters before application of primer as specified in
specification.

 Concrete and masonry surfaces shall be wire brushed as specified in the specification.

 Skilled workers shall be used for application of paint system.

 Prior commencing painting PE will check surfaces for moisture content with approved moisture testing device. Do not apply the paint unless the
moisture content is less than 8% as specified in specification.

 After surface is ready to receive primer coat, surface preparation ITR will be raised for the CONSULTANT’s inspection and approval.

 Application of Stone Finish Paint on Exterior finishes will be done as per specification using approved material.

 After the application of stone finish paint is completed and all the minor defects ratified, ITR for final inspection will be raised to the
CONSULTANT’s for inspection and approval of finished works.

 All activities on these stages will be carried out under full supervision of concerned Project Engineer, Foremen and HSE Officers.
10.0 ATTACHMENTS

 Proposed System of Application.

 Application Method Statement for EuroStone.

 StonePrime – Primer for stone paint systems

 EuroStone – Premium quality, natural stone like finishes for exterior and interiors. Highly decorative.

 Nanoclear – Protective clear coat for Stone-Paint Systems with Nano-Quartz Technology

 ITP

 Checklist

 Risk Assessment

Issue No.: 0
Revision No.: 0