PT100 SCANNER

EPLC9600-CHANNEL8 96 x 96 DIN 1/4

8 Channel PT-100 Scanner
EPLC9600-CHANNEL8 96x96 1/4 DIN

- 128 x 64 Graphical LCD display

- 8 PT-100 temperature sensor inputs
- ON-OFF control
- Relay or (pnp “source”) transistor output
- Sensor error detection
- Adjustable temperature offset
- 3 Different alarm and pre-alarm types for each channel
(High, Low and Band Alarms)
- User defined channel labels
- Display scan modes
- Operating with Real Time Clock (RTC)
- ModBus RTU communication protocol
(RS-232, RS-485 and Ethernet communication)
- Data Logging to USB Flash Memory
- Adjustable data logging time interval
- Password protection for programming mode

Introduction Manual. ENG EPLC-9600 CHANNEL8 V04 07/13

ABOUT INSTRUCTION MANUAL

Instruction manual of EPLC9600-CHANNEL8 consists of two main sections. Explanation

of these sections are below. Also, there are other sections which include order information and
technical specifications of the device. All titles and page numbers in instruction manual are in
“CONTENTS” section. User can reach to any title with section number.

Installation:

In this section, physical dimensions of the device, panel mounting, electrical wiring,
physical and electrical installation of the device to the system are explained.

Operation and Parameters:

In this section user interface of the device, accessing to the parameters, description of the
parameters are explained.

Also in these sections, there are warnings to prevent serious injury while doing the
physical and electrical mounting or using the device.

Explanation of the symbols which are used in these sections are given below.

c This symbol is used for safety warnings. User must pay attention to these
warnings.

a
This symbol is used to determine the dangerous situations as a result of an electric
shock. User must pay attention to these warnings definitely.

This symbol is used to determine the important notes about functions and usage of
i the device.

2
CONTENTS
1.PREFACE............................................................................................................................................ Page 5
1.1 GENERAL SPECIFICATIONS
1.2 ORDERING INFORMATION
1.3 WARRANTY
1.4 MAINTENANCE

2.INSTALLATION.................................................................................................................................... Page 7
2.1 GENERAL DESCRIPTION
2.2 FRONT VIEW AND DIMENSIONS OF EPLC9600-CHANNEL8
2.3 PANEL CUT-OUT
2.4 ENVIRONMENTAL RATINGS
2.5 PANEL MOUNTING
2.6 INSTALLATION FIXING CLAMP
2.7 REMOVING FROM THE PANEL
3.ELECTRICAL WIRING........................................................................................................................ Page 12
3.1 TERMINAL LAYOUT AND CONNECTION INSTRUCTIONS
3.2 ELECTRICAL WIRING DIAGRAM
3.2.1 DEVICE WITH RELAY OUTPUTS
3.2.2 DEVICE WITH TRANSISTOR OUTPUTS
3.3 SUPPLY VOLTAGE INPUT CONNECTION OF THE DEVICE
3.4 SUPPLY VOLTAGE INPUT CONNECTION OF TRANSISTOR OUTPUTS
3.5. GALVANIC ISOLATION TEST VALUE OF EPLC9600-CHANNEL8 WITH RELAY OUTPUTS
3.6. GALVANIC ISOLATION TEST VALUE OF EPLC9600-CHANNEL8 WITH TRANSISTOR
OUTPUTS

4. CABLE CONNECTION BETWEEN RS232 TERMINAL OF THE DEVICE AND PC ........................ Page 19

5. CONNECTION FOR RS485 SERIAL COMMUNICATION................................................................. Page 20

6. DEFINETION OF THE FRONT PANEL AND ACCESSING TO THE PARAMETERS....................... Page 21

6.1 DEFINETION OF FRONT PANEL
6.2 MAIN OPERATION SCREEN DEFINETION
6.3 ACCESSING TO THE OPERATOR PARAMETER PAGES
6.4 ACCESSING TO THE TECHNICIAN PARAMETER PAGES
6.5 OPERATOR PAGES PARAMETERS DEFINETIONS
6.6 TECHNICIAN PAGES PARAMETERS DEFINETIONS
6.6.1 PAGE-1 PARAMETERS
6.6.2 PAGE-2 PARAMETERS
6.6.3 PAGE-3 AND PAGE-4 PARAMETERS
6.6.4 RS232 SETUP PAGES PARAMETERS
6.6.5 RS485 SETUP PAGES PARAMETERS
6.6.6 USB SETUP PAGES PARAMETERS
6.6.7 ETHERNET SETUP PAGES PARAMETERS
6.6.8 REAL TIME (RTC) SETUP PAGES PARAMETERS

7.OPERATION GRAPHICS OF ALARM AND PRE-ALARM TYPE....................................................... Page 39

8.MODBUS ADDRESS........................................................................................................................... Page 40

8.1 OUTPUT ADDRESSES
8.2 PROCESS VALUES ADDRESSES

9.SPECIFICATIONS................................................................................................................................Page 41

10.OTHER INFORMATIONS.................................................................................................................. Page 41

3
EU DECLARATION OF CONFORMITY

Manufacturer’s Name : EMKO ELEKTRONIK A.S.

Manufacturer’s Address : DOSAB, Karanfil Sk., No:6,
16369 Bursa, TURKEY

The manufacturer hereby declares that the product:

Product Name : CHANNEL8 (8 Channel PT-100 Scanner)

Type Number : EPLC9600

Product Category : Electrical equipment for measurement, control and

laboratory use

Conforms to the following directives :

2006 / 95 / EC The Low Voltage Directive

2004 / 108 / EC The Electromagnetic Compatibility Directive

has been designed and manufactured to the following specifications:

EN 61000-6-4:2007 EMC Generic Emission Standard for Industrial Environments

EN 61000-6-2:2005 EMC Generic Immunity Standard for Industrial Environments

EN 61010-1:2001 Safety Requirements for electrical equipment for measurement, control

and laboratory use

When and Where Issued Authorized Signature

nd
22 June 2011 Name : Serpil YAKIN

Bursa-TURKEY Position : Quality Manager

4
1.Preface
EPLC9600-CHANNEL8 series 8 channel PT100 scanner devices are designed for
measuring and logging temperature. They can be used in many applications with their PT-100
process input, alarm outputs, selectable alarm functions, RS-232 / RS-485 / Ethernet / USB
communications.

Application Fields
Glass
Plastic
Petro-Chemistry
Textile
Automative
Machine production industries
etc...

Applications
Heating
Baking Ovens
Incubators
Storages
Air Conditioning
etc..

1.1 General Specifications

EPLC9600
CHANNEL8 Standard
Power Supply Universal Supply Input
100-240 V V, 50/60Hz
Input
Optional Supply Input
24V V 50/60Hz, 24V Z

Process Inputs PT-100(2-wire)

Standard
Relay Outputs Alarm Outputs

Optional Temperature Alarm Out

Transistor Outputs Alarm Outputs

Standard
Communication RS232

Optional Modbus RTU Protocol

Communication RS485

Optional
Modbus RTU Over TCP
Communication ETHERNET Modbus RTU TCP/IP
Protocol
Optional
Communication USB Temperature Data Logging

5
1.2 Ordering Information
A . B C D E
EPLC9600-CHANNEL8 All order information of EPLC9600-
( 96 x 96 1/4 DIN) . 2 CHANNEL8 are given on the table at left.
User may form appropriate device
A Supply Voltage configuration from information and codes
1 100...240V V (- %15;+%10) 50/60Hz
2 24VV(-%15;+%10) 50/60Hz 24VZ(-%15;+%10) that at the table and convert it to the ordering
9 Customer codes.
B Outputs Firstly, supply voltage then other
10 Relay outputs with 2 common
R for each NO contact 5A max. (5A@250V at resistive load) spesifications must be deteermined. Please
for each Common contact 15A max (15A@250V at resistive load) fill the order code blanks according to your
10 pnp “source” Transistor outputs needs.
T Output current 1A Max. for each transistor output.

C Standard Serial Communication

Please contact us, if your needs are out of
2 RS-232 (up to 115200 baudrate, “No isolation”) the standards.
D Optional Communication-1
0 None
4 RS-485 (up to 115200 baudrate, “500VAC isolation”)
E ETHERNET (10Mbit/s, “1500VAC isolation”)
E Optional Communication-2
0 None
U USB (USB2.0 “for temperature data logging”)

1.3 Warranty
EMKO Elektronik warrants that the equipment delivered is free from defects in material and
workmanship. This warranty is provided for a period of two years. The warranty period starts from
the delivery date. This warranty is in force if duty and responsibilities which are determined in
warranty document and instruction manual performs by the customer completely.

1.4 Maintenance
Repairs should only be performed by trained and specialized personnel. Cut power to the device
before accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of
these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl
alcohol or water to clean the external plastic case.

6
2.Installation

c
Before beginning installation of this product, please read the instruction
manual and warnings below carefully.

In package ,
- One piece unit
- Two pieces mounting clamps
- One piece instruction manual

A visual inspection of this product for possible damage occured during shipment is
recommended before installation. It is your responsibility to ensure that qualified
mechanical and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power
off the system and separate the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch
and fuse as required.

Be sure to use the rated power supply voltage to protect the unit against damage and to
prevent failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble
with the unit can be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may
results in malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During the equipment is putted in hole on the metal panel while mechanical installation
some metal burrs can cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s fixing clamps. Do not do the
montage of the device with inappropriate fixing clamp. Be sure that device will not fall
while doing the montage.

It is your responsibility if this equipment is used in a manner not specified in this

instruction manual.

7
2.1 General Description

Mounting Clamp

Panel surface
(maximum thickness 15 mm / 0.59 inch)
Front Panel
IP65 protection
NEMA 4X

2.2 Front View and Dimensions of EPLC9600-CHANNEL8

Maximum 15 mm / 0.59 inch

96 mm / 3.78 inch

+/-
1 2 3 a/A .
Sym

4 5 6 ü
7 8

96 mm / 3.78 inch
12 ± 1 mm / 0.47 inch 84 mm / 3.31 inch

8
2.3 Panel Cut-out

129 mm / 5.08 inch (min)

129 mm / 5.08 inch (min)

92mm / 3.62 inch

92mm / 3.62 inch

9
2.4 Environmental Ratings

Operating Conditions

Operating Temperature : 0 to 50 °C

Max. Operating Humidity : 90% Rh (non-condensing)

Altitude : Up to 2000m.

c
Forbidden Conditions:
Corrosive atmosphere
Explosive atmosphere
Home applications (The unit is only for industrial applications)

2.5 Panel Mounting

1-Before mounting the device in your

panel, make sure that the cut-out is of
the right size.
1
2-Check front panel gasket position

3-Insert the device through the cut-out.

If the mounting clamps are on the unit,
put out them before inserting the unit to
the panel.

c
During installation into a metal panel, care should be taken to avoid injury from
metal burrs which might be present. The equipment can loosen from vibration
and become dislodged if installation parts are not properly tightened. These
precautions for the safety of the person who does the panel mounting.

10
2.6 Installation Fixing Clamp

2
The unit is designed for panel
1
mounting.

1-Insert the unit in the panel cut-out

from the front side.

2- Insert the mounting clamps to the

holes that located top and bottom
sides of device and screw up the
fixing screws until the unit
completely immobile within the
panel

c
Montage of the unit to a system must be done with it’s own fixing clamps. Do
not do the montage of the device with inappropriate fixing clamps. Be sure
that device will not fall while doing the montage.

2.7 Removing from the Panel

c Before starting to remove the unit from panel, power off the unit and the
related system.

1-Loosen the screws.

1
2-Pull mounting clamps from top
and bottom fixing sockets.

3-Pull the unit through the front

side of the panel

11
3.Electrical Wirings

c
You must ensure that the device is correctly configured for your application.
Incorrect configuration could result in damage to the process being
controlled, and/or personal injury. It is your responsibility, as the installer, to
ensure that the configuration is correct.
Device parameters has factory default values. These parameters must be
set according to the system’s needs.

c
Only qualified personnel and technicians should work on this equipment.
This equipment contains internal circuits with voltage dangerous to human
life. There is severe danger for human life in the case of unauthorized
intervention.

c
Be sure to use the rated power supply voltage to protect the unit against
damage and to prevent failure.

c Keep the power off until all of the wiring is completed so that electric shock
and trouble with the unit can be prevented.

3.1 Terminal Layout and Connection Instructions

Terminal layout for Terminal layout for

ethernet communication RS485 communication

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

a a
COMMUNICATION

COMMUNICATION
ETHERNET

D-
RS 485

D+
COMMUNICATION

COMMUNICATION
RS 232

RS 232

USB 2.0 USB 2.0

a a
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Max. 2.5mm / 0.098 inch

Wire Size:
18AWG/1mm² Torque Screw driver
Solid /Stranded 0,5Nm 0,8 x3mm

12
3.2 Electrical Wiring Diagram

3.2.1 Device with Relay Outputs

c
Electrical wiring of the device must be the same as ‘Electrical Wiring
Diagram’ below to prevent damage to the process being controlled and
personnel injury.
Power Supply Input
100...240V V (- %15;+%10) 50/60Hz 7VA
24VV(-%15;+%10) 50/60Hz 7VA
24VZ(-%15;+%10) 7W
Process Inputs
(PT-100) (It must be determined in order.)
CH-8 CH-7 CH-6 CH-5 CH-4 CH-3 CH-2 CH-1
PT-100

PT-100

PT-100

PT-100

PT-100

PT-100

PT-100

PT-100
AGND

N L
(-) (+)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMMUNICATION
ETHERNET

RS485
OR

COMMUNICATION
COMMUNICATION

RS 232
USB 2.0

GENERAL PRE- ALR.

5 x 5A@250VV 5 x 5A@250VV
GENERAL ALR.
CH-6 ALARM

CH-7 ALARM

CH-8 ALARM
CH-1 ALARM

CH-2 ALARM

CH-3 ALARM

CH-4 ALARM

CH-5 ALARM

OUTPUT

OUTPUT

OUTPUT

OUTPUT

OUTPUT
OUTPUT

OUTPUT

OUTPUT

OUTPUT

OUTPUT

COMMON-2
COMMON-1

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Common1 Common2

Relay Outputs Relay Outputs

(Alarm Outputs for (Alarm Outputs for
Channels 1 to 5) Channels 6 to 8,
General Alarm Output and
General Pre-Alarm Output )
CH = CHANNEL

i RS485, Ethernet and USB communications are optional

13
3.2.2 Device with Transistor Outputs

c
Electrical wiring of the device must be the same as ‘Electrical Wiring
Diagram’ below to prevent damage to the process being controlled and
personnel injury.

Power Supply Input

100...240V V (- %15;+%10) 50/60Hz 7VA
24VV(-%15;+%10) 50/60Hz 7VA
24VZ(-%15;+%10) 7W
Process Inputs
(PT-100) (It must be determined in order.)
CH-8 CH-7 CH-6 CH-5 CH-4 CH-3 CH-2 CH-1
PT-100

PT-100

PT-100

PT-100

PT-100

PT-100

PT-100

PT-100
AGND

N L
(-) (+)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMMUNICATION
ETHERNET

RS485
OR

COMMUNICATION
COMMUNICATION

RS 232
USB 2.0

GENERAL PRE- ALR.

10 x 1A@24VZ
GENERAL ALR.
CH-6 ALARM

CH-7 ALARM

CH-8 ALARM
CH-1 ALARM

CH-2 ALARM

CH-3 ALARM

CH-4 ALARM

CH-5 ALARM

OUTPUT

OUTPUT

OUTPUT

OUTPUT

OUTPUT
OUTPUT

OUTPUT

OUTPUT

OUTPUT

OUTPUT

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

POWER
SUPPLY
24VZ ±%15

Transistor Outputs
(Alarm Outputs for
Channels 1 to 8,
General Alarm Output and
General Pre-Alarm Output )

CH = CHANNEL

i RS485, Ethernet and USB communications are optional

14
3.3 Supply Voltage Input Connection of the Device

Note-1
N aL
14 15
Note-2

Note-3
External Fuse
(1 A T)

c
Power
Supply
Switch
Power Supply
100-240V V (- %15;+%10) 50/60Hz 7VA or,
24VV(-%15;+%10) 50/60Hz 7VA or,
24VZ(-%15;+%10) 7W

Note-1 :There is an internal 33R W fusible flameproof resistor in 100-240 V V 50/60Hz

There is an internal 4R7 W fusible flameproof resistor in 24VW 50/60Hz

Note-2: “L” is (+), “N” is (-) for 24V Z Supply Voltage

Note-3: External Fuse is recommended

c
Make sure that the power supply voltage is same indicated on the instrument.
Switch on the power supply only after that all the electrical connection have
been completed.
Supply voltage range must be determined in order. While installing the unit,
supply voltage range must be controlled and appropriate supply voltage must
be applied to the unit. Controlling prevents damages in unit and system and
possible accidents as a result of incorrect supply voltage.

c
There is no power supply switch or fuse on the device. So a power supply
switch and a fuse must be added to the supply voltage input. Power supply
switch and fuse must be put to a place where user can reach easily.
Power supply switch must be two poled for seperating phase and neutral.
On/Off condition of power supply switch is very important in electrical
connection. On/Off condition of power supply switch must be signed for
preventing the wrong connection.

External fuse must be on phase connection in Vsupply input.

External fuse must be on (+) line connection in Zsupply input.

c
The instrument is protected with an internal fuse (Please refer to Note-1 for
information). In case of failure it is suggested to return the instrument to the
manufacturer for repair.

15
3.4 Supply Voltage Input Connection of the Transistor Outputs

This power supply connection is need only when transistor type outputs are
i used.

(-) a (+)
29 30

Note-2

Note-1
c
Power
Supply
Switch

Supply Voltage
24V Z (±15%)

Note-1 : External fuse is recommended.

Note-2 : Fuse value must be select according to the system.

c
Make sure that the power supply voltage is the same indicated on the
instrument.
Switch on the power supply only after that all the electrical connections have
been completed.
While installing the unit, supply voltage range must be controlled and
appropriate supply voltage must be applied to the unit. Controlling prevents
damages in unit and system and possible accidents as a result of incorrect
supply voltage.

c
There is no power supply switch on the device. So a power supply switch must
be added to the supply voltage input. In accordance with the safety regulations,
the power supply switch shall bring the identification of the relevant
instrument.Power supply switch shall be easily accessible by the user.
Power switch must be two poled for seperating phase and neutral. On/Off
condition of power switch is very important in electrical connection. On/Off
condition of power switch must be signed for preventing the wrong connection.

If an external fuse is used, it must be on (+) line connection in Zsupply input.

16
3.5 Galvanic Isolation Test Values of EPLC9600-CHANNEL8 with Relay Outputs

Supply Input 14
of Device 15

2000V V
Analog inputs

2000V V
Relay Outputs

2000V V
RS 232

2000V V
RS 485

2000V V
Usb

2000V V
Ethernet

17
3.6 Galvanic Isolation Test Values of EPLC9600-CHANNEL8 with Transistor Outputs

2000V V
Supply Input 14 Supply Input 29
of Device 15 of Output Card 30

2000V V 500V V
Analog inputs

2000V V
Transistor Outputs

2000V V 500V V
RS 232

2000V V 500V V
RS 485

2000V V 500V V
Usb

2000V V 1500V V
Ethernet

18
4. Cable Connection Between RS-232 Terminal of the Device and PC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

PC (Personal Computer)
9 Pin DCON connection

NA
1
9 RX TX
2
8 TX RX
3
7 GND
4
6 GND
5 NA
NA

Cable Lenght must be

max. 12 meters for
9600 baud rate
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

19
 5. Connection for RS-485 Serial Communication

PC(Personal Computer)

RS-232 Ş RS-485
Convertor

RS-232 SLAVE-1
D- D+
MASTER Connection 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Cable Rt

32 terminal can be connected in RS-485 line D- D-

D+
D+
Rt resistor = 120 W

For communication connection Twisted Pair

cable must be used

Cable lenght can be maximum 1000 meters 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

in 9600 baud rate.

SLAVE-2
When baud rate increases, cable lenght must 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

be decreased.

D- D-
D+
D+

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

SLAVE-N
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

D- D-
D+
D+

Rt
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

20
6. Definetion of the Front Panel and Accessing to the Parameters
6.1. Definition of Front Panel

128 x 64 Pixel
Graphical LCD

Channel Standard
Selection Function
Buttons Buttons

Programming Mode
Access Button
ENTER BUTTON
ü This button is used to confirm the variable value in variable value changing screen.

ESCAPE BUTTON
This button is used to exit from variable value changing screen to preceding visualization screen
without saving variable value, and return to main operation screen.

DELETE BUTTON
This button is used to delete the last digit of the value in variable value changing screen.

a/A
CHANGE CASE BUTTON
This button is used to changing the character between uppercase and lowercase, which cursor is show
for string variable in variable value changing screen.
+/-
. SIGN & SYMBOL BUTTON
Sym This button is used to changing the sign value for sign type variables, entering the dot for real type
and entering the symbol character for string type variables in variable value changing screen.

DOWN BUTTON
This button is used to decrement the digit, which cursor is show of variable in variable value changing
screen and used to accessing next programming page in programming mode.

UP BUTTON
This button is used to increment the digit, which cursor is show of variable in variable value changing
screen and used to accessing previous programming page in programming mode.

RIGHT BUTTON
This button is used to move cursor to the right side for one digit in variable value changing screen and
selecting the variable for changing in programming mode.

LEFT BUTTON
This button is used to move cursor to the left side for one digit in variable value changing screen and
selecting the variable for changing in programming mode.
PROGRAMMING MODE ACCESSING BUTTON
This button is used to accessing to programming mode parameters pages.

21
 6.2. Main Operation Screens Definetion
If the display type parameter value DSP.TYPE = 1

Process Value Pre-Alarm Status

Analog Channels Alarm Status
Names
Analog Channels
Numbers
Alarm Messages

MAIN OPERATION SCREEN-1

Press right button for

accessing the main
operation screen-2

MAIN OPERATION SCREEN-2

Press left button for

accessing the main
operation screen-1

If more than one alarm messages is present, each alarm message is showing on LCD screen
i during 1 second.

If the display scan parameter value DSP.SCAN = 1, each main operation screen is showing on
i LCD screen during time defined by SCAN TIME parameter value.

22
If the display type parameter value DSP.TYPE = 2

Analog Channels Analog Channels

Numbers Names

Process Value
Set Value
Alarm Messages

MAIN OPERATION ( CHANNEL-1 SCREEN)

Press number
(1,2,3,4,5,6,7 or 8)
buttons for
accessing the
relevant channel
screen. MAIN OPERATION ( CHANNEL-4 SCREEN)

If more than one alarm messages is present, each alarm message is showing on LCD screen
i during 1 second.

If the display scan parameter value DSP.SCAN = 1, each main operation screen is showing
i on LCD screen during time defined by SCAN TIME parameter value.

23
 6.3. Accessing to the Operator Parameter Pages
OPERATOR PARAMETERS SECTION
MAIN OPERATION SCREEN PASSWORD SCREEN

When programming mode access button is pressed Press right or left

and released before 5 seconds is expire, If operator button for selecting the
password is different from 0, operator parameter password parameter.
section password screen will be observed, If operator
password is 0 then operator parameter screen will be
observed.

OPERATOR PARAMETERS SECTION OPERATOR PARAMETERS SECTION

PASSWORD SCREEN PASSWORD ENTERING SCREEN

Minimum Maximum

0 0 9999

Press enter button for accessing to Enter the operator parameter

password entering screen. section password with cursor
(lef, right, up and down) buttons.

OPERATOR PARAMETERS SECTION OPERATOR PARAMETER SCREEN

PASSWORD ENTERING SCREEN (CHANNEL-1 PARAMETERS)

Minimum Maximum
0 9999

1234 1.0.1

Press enter button for accessing Press right or left button for
to the operator section selecting the parameter.
parameters.

If no operation is performed for 20 seconds in operator parameters section, device turns to

i main operation screen automatically.

24
 OPERATOR PARAMETER SCREEN
(CHANNEL-1 PARAMETERS) PARAMETER ENTERING SCREEN

Minimum Maximum
100.0 oC
-200.0 650.0

1.0.1 100.0

Press enter button for accessing to Change the parameter value

parameter entering screen. with cursor
(lef, right, up and down)
buttons.

OPERATOR PARAMETER SCREEN

PARAMETER ENTERING SCREEN (CHANNEL-1 PARAMETERS)

Minimum Maximum
-200.0 650.0

200.0 1.0.1

Press enter button for return parameter Press number (1,2,3,4,5,6,7 or 8)

screen with saving parameter value, buttons for accessing the relevant
press escape button for return parameter channel’s parameter screen.
screen without saving parameter value.

OPERATOR PARAMETER SCREEN

(CHANNEL-7 PARAMETERS)

1.0.1

Other operator section parameters can be accessed

with same method explained above, press escape
button for return to main operation screen.

If no operation is performed for 20 seconds in operator parameters section, device turns to

i main operation screen automatically.

25
 6.4. Accessing to the Technician Parameter Pages
TECHNICIAN PARAMETERS SECTION
MAIN OPERATION SCREEN PASSWORD SCREEN

When programming mode access button is pressed Press right or left

for 5 seconds, If technician password is different from button for selecting the
0, technician parameter section password screen will password parameter.
be observed, If technician password is 0 then
technician parameter screen will be observed.

TECHNICIAN PARAMETERS SECTION TECHNICIAN PARAMETERS SECTION

PASSWORD SCREEN PASSWORD ENTERING SCREEN

Minimum Maximum

0 0 9999

Press enter button for accessing to Enter the technician parameter

password entering screen. section password with cursor
(lef, right, up and down) buttons.

TECHNICIAN PARAMETERS SECTION TECHNICIAN PARAMETER SCREEN

PASSWORD ENTERING SCREEN (PAGE - 1 “CHANNEL-1 PARAMETERS”)

Minimum Maximum
0 9999

5678

Press enter button for accessing Press number (1,2,3,4,5,6,7 or 8)

to the technician section buttons for accessing the relevant channel’s
parameters. parameter screen.Press down button for
accessing to next parameter page.

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

26
TECHNICIAN PARAMETER SCREEN TECHNICIAN PARAMETER SCREEN
(PAGE - 2) (PAGE - 3)

Press down button for accessing next Press down button for accessing next
parameter page, press up button for parameter page, press up button for
accessing previous parameter page. accessing previous parameter page.

TECHNICIAN PARAMETER SCREEN TECHNICIAN PARAMETER SCREEN

(PAGE - 4) (PAGE - 5 “RS 232 PAGE”)

Press down button for accessing next Press down button for accessing next
parameter page, press up button for parameter page, press up button for
accessing previous parameter page. accessing previous parameter page.

TECHNICIAN PARAMETER SCREEN TECHNICIAN PARAMETER SCREEN

(PAGE - 6 “RS 485 PAGE”) (PAGE - 7 “USB PAGE”)

Press down button for accessing next Press down button for accessing next
parameter page, press up button for parameter page, press up button for
accessing previous parameter page. accessing previous parameter page.

If the device has a optional RS485 communication then RS 485 page is observed,
i If the device has a optional USB communication then USB page is observed.
Otherwise these pages are not observed.
If no operation is performed for 20 seconds in technician parameters section, device turns to
i main operation screen automatically.

27
TECHNICIAN PARAMETER SCREEN TECHNICIAN PARAMETER SCREEN
(PAGE - 8 “ETHERNET PAGE”) (PAGE - 9 “RTC PAGE”)

Press down button for accessing next Press up button for accessing
parameter page, press up button for previous parameter page,
accessing previous parameter page. press escape button for return to
main operation screen.

If the device has a optional ETHERNET communication then ETHERNET page is observed,
i otherwise this page is not observed.

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

28
 6.5. Operator Pages Parameters Definetions

Analog Channel
Number

1.0.1

Channel Selection
Buttons

Parameter Explanation Unit Min Max Default

O
ALARM SET Alarm Set Value For Channel-X C -200.0 650.0 100.0
O
PRE. A. SET Pre-Alarm Set Value For Channel-X C -200.0 650.0 90.0
DSP. BACKLIGHT Display Backlight Mode - 0 2 1
CONTRAST Display Contrast Value - 30 60 45

ALARM SET
Alarm set value for selected channel is can be adjusted according to this parameter.
PRE. A.SET
Pre- Alarm set value for selected channel is can be adjusted according to this parameter.
DSP LIGHT
Display backlight is can be controlled by this parameter value. If parameter value;
0 = LCD backlight is continuously OFF
1 = LCD backlight is continuously ON
2 = “power safe mode” If any button is not pressed during 30 secs. LCD backlight is automatically
changed OFF mode, when any button is pressed LCD backlight is changed ON mode again.
CONTRAST
Display contrast value is can be controlled by this parameter value.
REV. NUM “Software Revision Number”
Device software revision number is can be seen by this parameter.
This parameter is can not be changed, it’s only observed.

Alarm Set Parameters Modbus Addresses Pre-Alarm Set Parameters Modbus Addresses
Parameter Name Modbus Address Parameter Name Modbus Address
CH-1 ALR. SET (*) 42050 CH-1 P-ALR. SET (*) 42051
CH-2 ALR. SET (*) 42054 CH-2 P-ALR. SET (*) 42055
CH-3 ALR. SET (*) 42058 CH-3 P-ALR. SET (*) 42059
CH-4 ALR. SET (*) 42062 CH-4 P-ALR. SET (*) 42063
CH-5 ALR. SET (*) 42066 CH-5 P-ALR. SET (*) 42067
CH-6 ALR. SET (*) 42070 CH-6 P-ALR. SET (*) 42071
CH-7 ALR. SET (*) 42074 CH-7 P-ALR. SET (*) 42075
CH-8 ALR. SET (*) 42078 CH-8 P-ALR. SET (*) 42079

CH = CHANNEL
i (*) These parameters are displayed on LCD screen with point, so that the parameters values
are 10 times than the real values for modbus function.

Channel number is can be seen upper left side of the display and can be selected by pressing
i the channel selection buttons.

If no operation is performed for 20 seconds in operator parameters section, device turns to

i main operation screen automatically.

29
 6.6. Technician Pages Parameters Definetions
6.6.1. Page-1 Parameters

Technician Parameter
Analog Channel Page Number
Number

Channel Selection
Buttons

Parameter Explanation Unit Min Max Default

ALARM TYPE Alarm Type For Channel-X - 1 3 2
PRE. A. TYPE Pre-Alarm Type For Channel-X - 1 3 2
O
HYSTERESIS Hysteresis Value For Channel-X C -400.0 400.0 1.0
O
BAND ALARM Bandwith Value For Channel-X C -400.0 400.0 10.0
SENSOR ALARM Sensor Alarm Ena./Dis Selection For Channel-X ENA/DIS 0 1 1
O
PV. OFFSET Process Offset Value For Channel-X C -50.0 50.0 0

ALARM TYPE
Alarm type for selected channel is can be adjusted according to this parameter. If parameter value,
1 = Low Alarm
2 = High Alarm
3 = Band Alarm is selected.
PRE. A. TYPE
Pre-Alarm type for selected channel is can be adjusted according to this parameter. If parameter value,
1 = Low Alarm
2 = High Alarm
3 = Band Alarm is selected.
HYSTERESIS
Hysteresis parameter value for Alarm and Pre-Alarm is can be adjusted by this parameter.
BAND ALARM
Bandwith for Band alarm is can be adjusted by this parameter value.
SENSOR ALARM
Sensor break alarm for selected channel is can be disable or enable by this parameter. If parameter value,
0 = Sensor break alarm disable
1 = Sensor break alarm enable
PV. OFFSET
Process offset value for selected channel is can be adjusted by this parameter.

Channel number is can be seen upper left side of the display and can be selected by pressing
i the channel selection buttons.

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

30
Alarm Type Selection Parameters Band Alarm Selection Parameters
Modbus Addresses Modbus Addresses
Parameter Name Modbus Address Parameter Name Modbus Address
CH-1 ALARM TYPE 42082 CH-1 BAND ALARM (*) 42053
CH-2 ALARM TYPE 42085 CH-2 BAND ALARM (*) 42057
CH-3 ALARM TYPE 42088 CH-3 BAND ALARM (*) 42061
CH-4 ALARM TYPE 42091 CH-4 BAND ALARM (*) 42065
CH-5 ALARM TYPE 42094 CH-5 BAND ALARM (*) 42069
CH-6 ALARM TYPE 42097 CH-6 BAND ALARM (*) 42073
CH-7 ALARM TYPE 42100 CH-7 BAND ALARM (*) 42177
CH-8 ALARM TYPE 42103 CH-8 BAND ALARM (*) 42181

Pre-Alarm Type Selection Parameters Sensor Alarm Selection Parameters

Modbus Addresses Modbus Addresses
Parameter Name Modbus Address Parameter Name Modbus Address
CH-1 PRE. A. TYPE 42083 CH-1 SENSOR ALARM 42084
CH-2 PRE. A. TYPE 42086 CH-2 SENSOR ALARM 42087
CH-3 PRE. A. TYPE 42089 CH-3 SENSOR ALARM 42090
CH-4 PRE. A. TYPE 42092 CH-4 SENSOR ALARM 42093
CH-5 PRE. A. TYPE 42095 CH-5 SENSOR ALARM 42096
CH-6 PRE. A. TYPE 42098 CH-6 SENSOR ALARM 42099
CH-7 PRE. A. TYPE 42101 CH-7 SENSOR ALARM 42102
CH-8 PRE. A. TYPE 42104 CH-8 SENSOR ALARM 42105

Process Value Offset Parameters

Hysteresis Parameters Modbus Addresses Modbus Addresses
Parameter Name Modbus Address Parameter Name Modbus Address
CH-1 HYSTERESIS (*) 42052 CH-1 PV. OFFSET (*) 42116
CH-2 HYSTERESIS (*) 42056 CH-2 PV. OFFSET (*) 42117
CH-3 HYSTERESIS (*) 42060 CH-3 PV. OFFSET (*) 42118
CH-4 HYSTERESIS (*) 42064 CH-4 PV. OFFSET (*) 42119
CH-5 HYSTERESIS (*) 42068 CH-5 PV. OFFSET (*) 42120
CH-6 HYSTERESIS (*) 42072 CH-6 PV. OFFSET (*) 42121
CH-7 HYSTERESIS (*) 42176 CH-7 PV. OFFSET (*) 42122
CH-8 HYSTERESIS (*) 42180 CH-8 PV. OFFSET (*) 42123

CH = CHANNEL

i (*)These parameters are displayed on LCD screen with point, so that the parameters values
are 10 times than the real values for modbus function.
If no operation is performed for 20 seconds in technician parameters section, device turns to
i main operation screen automatically.

31
 6.6.2. Page-2 Parameters

Parameter Explanation Unit Min Max Default Address

TECH. PW. Technician Section Password - 0 9000 0 42106
OPR. PW. Operation Section Password - 0 9000 0 42107
DSP. TYPE Main Operation Screen Type - 1 2 2 42128
DSP. SCAN Display Scan ON/OFF ON/OFF 0 1 1 42129
SCAN TIME Display Scan Period SEC. 1 3600 2 42130
LANGUAGE Device Language Selection - 0 1 1 42136

TECH. PW
Password for entering to the technician section is defined with this parameter.
If it is 0, technician section accessed without entering password.
OPR. PW
Password for entering to the operator section is defined with this parameter.
If it is 0, operator section accessed without entering password.
DSP. TYPE
Main operation screen type is adjusted by this parameter. If parameter value,
1 = Multiple channel view
2 = Single channel view is selected.
DSP. SCAN
Display channel scanner mode is adjusted by this parameter. If parameter value,
0 = Display channel scanner mode OFF
1 = Display channel scanner mode ON
SCAN TIME
Display scan period is adjusted by this parameter. All main operation screen is displayed during time
defined by this parameter.
LANGUAGE
Device Language is selected by this parameter. If parameter value,
0 = TÜRKÇE
1 = ENGLISH

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

32
 6.6.3. Page-3 and Page-4 Parameters

Channel Names
Channel
Enable/Disable
Selection
Channel
Numbers

Parameter Explantion Unit Min Max Default Address

CH-1 NAME Channel-1 Name String - - SENSOR-1 42000 - 42004
CH-2 NAME Channel-2 Name String - - SENSOR-2 42005 - 42009
CH-3 NAME Channel-3 Name String - - SENSOR-3 42010 - 42014
CH-4 NAME Channel-4 Name String - - SENSOR-4 42015 - 42019
CH-5 NAME Channel-5 Name String - - SENSOR-5 42020 - 42024
CH-6 NAME Channel-6 Name String - - SENSOR-6 42025 - 42029
CH-7 NAME Channel-7 Name String - - SENSOR-7 42030 - 42034
CH-8 NAME Channel-8 Name String - - SENSOR-8 42035 - 42039
CH-1 I/O Channel-1 Enable/Disable ENA/DIS 0 1 1 42108
CH-2 I/O Channel-2 Enable/Disable ENA/DIS 0 1 1 42109
CH-3 I/O Channel-3 Enable/Disable ENA/DIS 0 1 1 42110
CH-4 I/O Channel-4 Enable/Disable ENA/DIS 0 1 1 42111
CH-5 I/O Channel-5 Enable/Disable ENA/DIS 0 1 1 42112
CH-6 I/O Channel-6 Enable/Disable ENA/DIS 0 1 1 42113
CH-7 I/O Channel-7 Enable/Disable ENA/DIS 0 1 1 42114
CH-8 I/O Channel-8 Enable/Disable ENA/DIS 0 1 1 42115

I/O “Channel Enable/Disable Selection Parameter”

Channel is enabled and disabled by this parameter. If channel is selected as a disabled this channel is can
not be observed in main operation scren for single view mode, channel alarm is not be controlled and
analogue value for this channel is can not be recording on USB file. If parameter value,
0 = Channel is disable
1 = Channel is enable
CHANNEL NAME “Channels label definition ”
All channels have their own label, is displayed in main operation screen. channel labels is can be adjusted
by this parameter. Channel labels are can be adjusted maximum 10 characters.

CH = CHANNEL
If no operation is performed for 20 seconds in technician parameters section, device turns to
i main operation screen automatically.

33
 6.6.4. RS232 Setup Pages Parameters

Parameter Explanation Unit Min Max Default Address

BAUDRATE Baudrate For RS232 Communication - 1 6 6 42124
PARITY Parity For RS232 Communication - 0 2 0 42125
STOP BIT Stop Bit For RS232 Communication - 1 2 1 42126
ID ID For RS232 Communication - 1 247 1 42127

BAUDRATE
Modbus communication baudrate for RS232 is can be adjusted by this parameter. If parameter value,
1 = 4800
2 = 9600
3 = 19200
4 = 38400
5 = 57600
6 = 115200
PARITY
Modbus communication parity bit for RS232 is can be adjusted by this parameter. If parameter value,
0 = No Parity
1 = ODD Parity
2 = EVEN Parity
STOP BIT
Modbus communication stop bit for RS232 is can be adjusted by this parameter. If parameter value,
1 = 1 Stop bit
2 = 2 Stop bits
ID
Modbus communication device ID for RS232 is can be adjusted by this parameter.
This parameter value is can be adjusted from 1 to 247 (except 85 and 170).

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

34
 6.6.5. RS485 Setup Pages Parameters

Parameter Explanation Unit Min Max Default Address

BAUDRATE Baudrate For RS485 Communication - 1 6 2 42132
PARITY Parity For RS485 Communication - 0 2 0 42133
STOP BIT Stop Bit For RS485 Communication - 1 2 1 42134
ID ID For RS485 Communication - 1 247 1 42135

BAUDRATE
Modbus communication baudrate for RS485 is can be adjusted by this parameter. If parameter value,
1 = 4800
2 = 9600
3 = 19200
4 = 38400
5 = 57600
6 = 115200
PARITY
Modbus communication parity bit for RS485 is can be adjusted by this parameter. If parameter value,
0 = No Parity
1 = ODD Parity
2 = EVEN Parity
STOP BIT
Modbus communication stop bit for RS485 is can be adjusted by this parameter. If parameter value,
1 = 1 Stop bit
2 = 2 Stop bits
ID
Modbus communication device ID for RS485 is can be adjusted by this parameter.

If the device has a optional RS485 communication then RS 485 page is observed,
i Otherwise these page is not observed.

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

35
 6.6.6. USB Setup Page Parameters

Parameter Explanation Unit Min Max Default Address

FILE NAME USB File Name String - - CHAN8.txt 42040 - 42044
LABEL USB Label String - - SAMPLE 42045 - 42049
SAVE TIME USB Time Record ENA/DIS - 0 1 1 42137
SAMP. TIME USB Record Time Interval Sec. 0 3600 1 42138

FILE NAME
USB file name for recording analogue values is can be adjusted by this parameter. File name can be
adjusted maximum 10 characters. Recording file on usb is “csv” format and all data is seperated each
other with tab. Example file format is explained below.
LABEL
When the analogue values are recorded on USB file, user can be defined label for this recording. Label
can be adjusted maximum 10 characters. Label are recorded at the end of every lines of file.
SAVE TIME
When the analogue values are recorded on USB file, user can be save the recording time on the file.
Recording time is recorded at the beginning of every lines of file.
0 = Real time is not recorded on USB file
1 = Real time is recorded on USB file for every sample
SAMPLE TIME
Record time interval is can be adjusted by this parameter. Analogue values are recorded on USB file with
this time interval. If this parameter value is 0 usb recording is disabled.
FLASH MEM. PLUGGED “USB Flash Memory Stick Detected Test”
When the usb flash memory stick is plugged to the device FLASH MEM.PLUGGED led is light on.
This parameter is can not be changed, it’s used to inform the user whether USB is plugged.

USB Recording File Example

2011-06-23-17:26:08 130.6 129.1 130.5 129.5 130.0 129.9 130.3 129.1 SAMPLE
2011-06-23-17:26:09 130.6 129.1 130.5 129.5 130.0 129.9 130.3 129.1 SAMPLE
2011-06-23-17:26:10 130.6 129.1 130.5 129.5 130.0 129.9 130.3 129.1 SAMPLE
2011-06-23-17:26:12 130.6 129.1 130.5 129.5 130.0 129.9 130.3 129.1 SAMPLE
2011-06-23-17:26:13 130.6 129.1 130.5 129.5 130.0 129.9 130.3 129.1 SAMPLE
Recording Time CH-1 CH-2 CH-3 CH-4 CH-5 CH-6 CH-7 CH-8 Label
Value Value Value Value Value Value Value Value

CH = CHANNEL
If the device has a optional USB communication then USB page is observed.
i Otherwise these page is not observed.

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

36
 6.6.7. ETHERNET Setup Page Parameters

Parameter Explanation Unit Min Max Default Address

DHCP DHCP Enable /Disable (** ) ENA/DIS 0 1 0 42150
ETH. PORT ETHERNET Port No (** ) - 1 65535 502 42151
ETH. IP NO Ethernet IP No (** ) - - - 192.168.0.250 42152 - 42153
ETH. NETMASK Ethernet Netmask (** ) - - - 255.255.255.0 42154 - 42155
ETH. GATEWAY Ethernet Gateway (** ) - - - 192.168.0.1 42156 - 42157
ETH. TCP/IP SLCT TCP/IP Select (** ) - 0 1 0 -
DEVICE MAC ADR. Device MAC Address (** ) - - - - 42158 - 42160
DHCP
DHCP is an automatic configuration protocol used on IP networks, If DHCP is enable, device is adjust our
ethernet communication configuration parameters (IP, Netmask,Gateway) dynamicaly for your network
system. If DHCP is disable, you must adjust ethernet configuration parameters (IP, Netmask,Gateway) for
your network system. If parameter value,
0 = DHCP DISABLE
1 = DHCP ENABLE
ETH.PORT
Ethernet port number is can be adjusted by this parameter.
NET MASK
Subnet mask for ethernet communication is can be adjusted by this parameter. If DHCP is selected as a
enable there is no need to adjust to this parameter, if DHCP is selected as a disable then user must adjust
this parameter according to the their own network system.
GATEWAY
Gateway for ethernet communication is can be adjusted by this parameter. If DHCP is selected as a
enable there is no need to adjust to this parameter, if DHCP is selected as a disable then user must adjust
this parameter according to the their own network system.
IP
IP address for ethernet communication is can be adjusted by this parameter. If DHCP is selected as a
enable there is no need to adjust to this parameter, if DHCP is selected as a disable then user must adjust
this parameter.
PORT SET
Ethernet port configuration is setting by this parameter, After the all parameter adjusted according to
system needs, this parameter value is must be adjusted to 1 for ethernet port setting, after ethernet port
setting is completed this parameter value is turn to zero automatically.
TCP/IP SLCT
TCP/IP protocol is selected by this parameter. 0 = Modbus RTU Over TCP/IP 1 = Modbus RTU TCP/IP

i (** ) These parameters are only read for modbus function.

If the device has a optional ETHERNET communication then ETHERNET pages is observed.
i Otherwise these pages are not observed.
If no operation is performed for 20 seconds in technician parameters section, device turns to
i main operation screen automatically.
37
 6.6.8. REAL TIME (RTC ) Setup Page Parameters

Press and hold on 3

seconds Enter button for
ü setting the RTC time value.

Parameter Explanation Unit Min Max Default

YEAR Year Value For RTC Time - 2010 3000 -
MONTH Month Value For RTC Time - 1 12 -
DAY Day Value For RTC Time - 1 31 -
HOUR Hour Value For RTC Time - 0 23 -
MINUTE Minute Value For RTC Time - 0 59 -
SECOND Second Value For RTC Time - 0 59 -

YEAR
Year value for RTC time is adjusted by this parameter.
MONTH
Month value for RTC time is adjusted by this parameter.
DAY
Day value for RTC time is adjusted by this parameter.
HOUR
Hour value for RTC time is adjusted by this parameter.
MINUTE
Minute value for RTC time is adjusted by this parameter.
SECOND
Second value for RTC time is adjusted by this parameter.

If no operation is performed for 20 seconds in technician parameters section, device turns to

i main operation screen automatically.

38
7. Operation Graphics of Alarm and Pre-Alarm Types

High Alarm
Alarm
Output

ON

OFF
HYS
Process Value
SET

Low Alarm
Alarm
Output

ON

OFF
HYS
Process Value
SET

Band Alarm

Alarm
Output

ON

OFF
HYS HYS
Process Value
(SET - (BAND/2)) SET (SET + (BAND/2))

SET = Alarm or Pre-Alarm Set value

i HYS = Hysteresis value for Alarm and Pre-Alarm output
BAND= Bandwidth for Band Alarm.
39
 8. Modbus Addresses
8.1. Output Addresses
OUTPUT ADDRESSES Unit Min Max Default Address
CH-1 ALARM OUT Channel-1 Alarm Output Status - - - - 00001
CH-2 ALARM OUT Channel-2 Alarm Output Status - - - - 00002
CH-3 ALARM OUT Channel-3 Alarm Output Status - - - - 00003
CH-4 ALARM OUT Channel-4 Alarm Output Status - - - - 00004
CH-5 ALARM OUT Channel-5 Alarm Output Status - - - - 00005
CH-6 ALARM OUT Channel-6 Alarm Output Status - - - - 00006
CH-7 ALARM OUT Channel-7 Alarm Output Status - - - - 00007
CH-8 ALARM OUT Channel-8 Alarm Output Status - - - - 00008
GEN. ALR. OUT General Alarm Output Status - - - - 00009
GEN.PREALR.OUT General Pre-Alarm Output Status - - - - 00010
Note-1: Outputs status are can be readed with modbus function-1 (read coils).
Device’s response for modbus function-1 is always 2 byte data although the modbus function request less
than 9 outputs port.

8.2. Process Values Addresses

PROCESS VALUES ADDRESSES Unit Min Max Default Address
CH-1 P. VALUE Channel-1 Process Value O
C - - - 30001
CH-2 P. VALUE Channel-2 Process Value O
C - - - 30002
CH-3 P. VALUE Channel-3 Process Value O
C - - - 30003
CH-4 P. VALUE Channel-4 Process Value O
C - - - 30004
CH-5 P. VALUE Channel-5 Process Value O
C - - - 30005
CH-6 P. VALUE Channel-6 Process Value O
C - - - 30006
CH-7 P. VALUE Channel-7 Process Value O
C - - - 30007
CH-8 P. VALUE Channel-8 Process Value O
C - - - 30008
Note-2: Process values are can be readed with modbus function-4 (read input register). Because of the
process values are displayed on LCD screen with point, the reading values from modbus is 10 times than
the real values.

40
 9. Specifications
Device Type : 8 Channel PT-100 Scanner
Housing & Mounting : 96mm x 96mm x 87.5mm 1/4 DIN 43700 plastic housing
for panel mounting. Panel cut-out is 92 x 92mm.
Protection Class : NEMA 4X (IP65 at front, IP20 at rear)
Weight : Approximately 0.4Kg.
Environmental Ratings : Standard, indoor at an altitude of less than 2000 meters
with none condensing humidity
o o o o
Storage / Operating Temperature: -20 C to +70 C / 0 C to +50 C
Storage / Operating Humudity : 90 % max. (None condensing)
Installation : Fixed installation
Overvoltage Category : II
Pollution Degree : II. office or workplace, none conductive pollution
Operating Conditions : Continuous
Device Supply Voltage and
Power : 100 - 240 V V (-%15 / +%10) 50/60 Hz. 7VA
24 V V (-%15 / +%10) 50/60 Hz. 7VA
24 V Z (-%15 / +%10) 7W
Output Card Supply Voltage
and Power : 24 VZ(±15%) - 5W (for Transistor output type)
Analogue Inputs : PT 100 (IEC751) (ITS90)
Accuracy : ± 0,25% of full scale
Line Compensation : Maximum 10 W
Sensor Break Protection : Upscale
Sampling Time : 400msecs.
Input Ressistance : > 10MW
Digital Output : Transistor or relay outputs
Transistor Output : PNP(source) type transistor output (Max. 1A@24VZ)
Relay Output : Resistive Load 5A@250VV
(Electrical Life : 100.000 operation (Full Load)
Standard Communication : RS-232 Communication (For Modbus RTU)
Optional Communication : RS-485 (For Modbus RTU) “500VV isolated”
10Mbits/s Ethernet (For Modbus RTU Over TCP -
Modbus RTU TCP/IP selectable) “1500VV isolated”
USB 2.0 (Data logging over Flash Stick Memory)
Display : 128 x 64 pixel graphical LCD
Approvals : GOST-R,
10. Other Informations
Manufacturer Information:
Emko Elektronik Sanayi ve Ticaret A.Ş.
Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369
BURSA/TURKEY Phone : +90 224 261 1900 Fax : +90 224 261 1912
Repair and Maintenance Service Information:
Emko Elektronik Sanayi ve Ticaret A.Ş.
Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369
BURSA/TURKEY Phone : +90 224 261 1900 Fax : +90 224 261 1912

Thank you very much for your preference to use Emko Elektronik
Your Technology Partner Products.
www.emkoelektronik.com.tr
41