PHOTOVOLTAIC MODULES

IS10P-IS20P-IS30P-IS40P-IS50P

IS10P, IS20P, IS30P, IS40P and IS50P photovoltaic modules are

composed of 36 high efficiency polycrystalline cells, manufactured
with the most innovative technologies of isotropic texturization and
antireflecting coating.

Encapsulation of cells is made between a high-transmission tempered

glass and a plastic. The encapsulant in Ethylene Vinyl Acetate (EVA)
covers the photovoltaics cells within the laminate thus protecting
them from etching. The texturization of the glass enables a maximum
concentration and diffusion of the light on the solar cells.

This allows us to guarantee a high performance, power and working

capability even in lower sunlight conditions. The Tedlar backside
contributes to a further protection of the module against the action of
climatic agents like humidity and dust, and provides a total electrical
isolation.

FEATURES

√ IS10P, IS20P, IS30P, IS40P and IS50P modules use an

anodized transparent and reinforced aluminium frame, highly
resistant to marine conditions.

√ IP 65 watertightness degree. The modules are totally sealed to

prevent water ingress.

√ Certifications:

TÜV 11-PPV-0000108/05-W02-TIC.

CEI/EN 61215 Ed. 2.

CEI/EN 61730 1-2 (2007).

√ High performance, even under low sunlight levels.

√ Maximum concentration and diffusion of light on the solar cells.

√ Cell protection through EVA encapsulation.

√ Tedlar coating for a further protection of the module against

humidity and dust, providing a total electrical isolation.

√ IP 65 Tyco waterproof junction box (fitted with 2 nos. by-pass

diodes on IS50P modules).
 PHOTOVOLTAIC MODULES
IS10P-IS20P-IS30P-IS40P-IS50P
Specifications subject to change without previous notice.

IS20P

IS10P

IS30P

IS40P
IS50P

Technical Data
MODEL
IS10P IS20P IS30P IS40P IS50P
Power 10 Wp 20 Wp 30 Wp 40 Wp 50 Wp
Nominal voltage 12.0V
Maximum power current (Imp) 0.6 A 1.2 A 1.63 A 2.4 A 2.69 A
Short circuit current (Isc) 0.67 A 1.34 A 1.68 A 2.5 A 2.82 A
Open circuit current (Voc) 21.6V 22.2V 22.2V 22.3V
Maximum power voltage (Vmpp) 17.0V 18.4V 18.4V 18.6V
NOCT (+/-2) 45ºC
Maximum system voltage 1,000V
Temperature range From -40º to +85ºC
Hail resistance Up to 25 mm at 90 km/h
Relative humidity Up to 100%
Dimensions (+/-2mm) 365x310x35 365x550x35 350x675x35 550x675x35 645x675x35
Weight 1.6 kg 3.0 kg 5.0 kg 5.0 kg 6.0 kg
Tolerance +/-3%

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 PHOTOVOLTAIC MODULES
IS75P-IS95P-IS120P-IS150P

IS75P, IS95P, IS120P and IS150P photovoltaic modules are

composed of 36 high efficiency polycrystalline cells, manufactured
with the most innovative technologies of isotropic texturization and
antireflecting coating.

Encapsulation of cells is made between a high-transmission tempered

glass and a plastic. The encapsulant in Ethylene Vinyl Acetate (EVA)
covers the photovoltaics cells within the laminate thus protecting
them from etching. The texturization of the glass enables a maximum
concentration and diffusion of the light on the solar cells.

This allows us to guarantee a high performance, power and working

capability even in lower sunlight conditions. The Tedlar backside
contributes to a further protection of the module against the action of
climatic agents like humidity and dust, and provides a total electrical
isolation.

FEATURES

√ IS75P, IS95P, IS120P and IS150P use a pre-holed transparent

reinforced anodized aluminium frame, providing an easy
installation of the module.

√ IP 65 watertightness degree. The modules are totally sealed to

prevent water ingress.

√ Certifications:

TÜV 11-PPV-0000108/05-W02-TIC.

CEI/EN 61215 Ed. 2.

CEI/EN 61730 1-2 (2007).

√ High performance, even under low sunlight levels.

√ Maximum concentration and diffusion of light on the solar cells.

√ Cell protection through EVA encapsulation.

√ Tedlar coating for a further protection of the module against

humidity and dust, providing a total electrical isolation.

√ IP 65 Tyco waterproof junction box fitted with 2 nos. by-pass

diodes.
 PHOTOVOLTAIC MODULES
IS75P-IS95P-IS120P-IS150P
Specifications subject to change without previous notice.

IS75P

IS120P

IS150P

IS95P

Technical Data
MODEL
IS75P IS95P IS120P IS150P
Power 75 Wp 95 Wp 120 Wp 150 Wp
Nominal voltage 12,0V
Maximum power current (Imp) 4.21 A 5.4 A 6.75 A 7.98 A
Short circuit current (Isc) 4.65 A 5.7 A 7.35 A 8.54 A
Open circuit current (Voc) 21.8V 22.3V 22.1V 22.5V
Maximum power voltage (Vmpp) 17.8V 17.7V 17.8V 18.8V
NOCT (+/-2) 45ºC
Maximum system voltage 1,000V
Temperature range From -40º to +85ºC
Hail resistance Up to 25 mm at 83 km/h
Relative humidity Up to 100%
Dimensions (+/-2mm) 785x675x35 1204x537x45 1205x675x35 1490x675x42
Weight 8.3 kg 9.3 kg 9.3 kg 13 kg
Tolerance +/-3%

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 SOLAR CHARGE CONTROLLERS

STECA PR
The STECA PR Solar Charge Controllers have been specially designed
for operation in difficult environments with high salt, moisture and dust
contents.

The PR 2020 IP is equipped with a large LCD display that shows

the current state of charge (SOC) as a percentage and graphically in
the form of a tank. This visual representation also provides operating
parameters, failure messages and self-test.

The “auto-adaptive” state of charge algorithm results in optimal battery

maintenance and control over the module output of up to 480 Wp,
which can be connected to it.

Manufactured according to ISO 9001 and 14001, RoHS, European

Standards and DIN IEC 68 part 2-30 (use in tropical areas).

FEATURES

√ Hybrid controller.

√ State of charge determination with Steca AtonIC (SOC).

√ Automatic detection of voltage.

→
√ PWM control.

√ Multistage charging technology.

√ Load disconnection depending on SOC.

√ Automatic load reconnection.

→

√ Temperature compensation.

√ Common grounding on one or several positive terminals, or

negative grounding on one terminal.

√ Integrated data logger.

→

√ Integrated self test.

√ Monthly maintenance charge.

√ Integrated energy meter.

 SOLAR CHARGE CONTROLLERS
STECA PR
Specifications subject to change without previous notice.

Certifications PR2020 IP PR
European Standards ✓ ✓
DIN EN ISO 9001:2000 ✓ ✓
DIN EN ISO 14001 ✓ ✓
DIN IEC 68, part 2-30 (use in tropical
✓ X
areas)
RoHS ✓ X

PR Controller
Electronic protections
Overcharge.
Deep discharge.
Load disconnection against over-discharging.
Reverse polarity protection of solar modules.
Reverse polarity protection of load and battery.
Short-circuit protection of solar modules.
Short-circuit protection of load.
Over-temperature.
Over-voltage.
Varistor protection against electromagnetic discharges.
Open circuit protection.
Reverse current protection at night.
PR2020 IP Controller

Model PR2020 IP PR1010 PR1515 PR2020 PR3030

System voltage 12V (24V)
Module current (input side) 20A 10A 15A 20A 30A
Load current (output side) 20A 10A 15A 20A 30A
Self-consumption <12 mA
End of charge voltage (float) Líquid 13.9 (27.8V) Gel 14.1V (28.2V)
Boost charge voltage 14.4V (28.8 V)
Compensation charge (disabled for gel
14.7V (29.4V)
batteries)
Reconnection voltage (SOC/LVR) >50%SOC/12.6V (25.2V)
Deep discharge protection (SOC) >30%SOC/11.1V (22.2)
Ambient temperature From -10º to +50ºC
Terminal size (single/fine wire) 16mm2/25mm2 AWG 6/4
Degree of protection IP 65 IP 32
Weight (gr) 350 350 350 350 350
Dimensions (mm) 122x147x55 187x96x44

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 SOLAR CHARGE CONTROLLERS

SunSaver-10/20
The Morningstar SunSaver is the market’s leading small solar charge
controller for both professional and consumer applications.

Its technology provides an exceptional reliability, a PWM battery

charging and a consistent high quality.

The SunSaver’s advanced design delivers outstanding performance

with an economical price.

Its low cost is made possible by Morningstar’s unique approach to

design and manufacturing:

• Quality programs ISO 9002.

• Latest power electronic technologies.
• Latest control and logic technologies.

FEATURES

√ 100% solid state.

√ Series design (not shunt ).

√ True 0 to 100% PWM duty cycle.

→
√ Setpoint accuracy to 35 mV.

√ Rated for 25% overloads.

√ Fully encapsulated in epoxy resin.

√ Marine rated terminals/anodised enclosure.

→

√ Temperature compensation.

√ Gelled/flooded battery selection.

√ No additional compensation needed.

√ Parallel connection for 40 A or more.

→

√ Green charging and red LVD indicators.

√ Approved for use in hazardous locations Class 1, Division 2,

Groups A, B, C, D.
 SOLAR CHARGE CONTROLLERS
SunSaver-10/20
Specifications subject to change without previous notice.

Mechanical specifications
Wire size: 5.2 mm2 (#10 AWG).
Enclosure material: Anodised aluminium.
Terminal material: Marine rated stainless steel.
Encapsulation material: Epoxy resin.
Weight: 0.23 kg.

Electrical specifications 12V 24V

Rated solar input 10/20 A
Rated solar load 10/20 A
25% current overload 5 min.
Regulation voltage: Gelled battery 14.1V 28.2V
Flooded battery 14.4V 28.8V
Load disconnection 11.5V 23.0V
LVD reconnection 12.6V 25.2V
Temperature Compensation (mV/°C) -28 -56
Self-consumption From 6 to 10 mA
Operating temperature From -40º to +85ºC

SOLAR RATING (A) LOAD RATING (A) LVD 12V 24V

MODEL 0 10 20 0 10 20
. SS-10
. SS-10L
. SS-10-24V
. SS-10L-24V
. SS-20L
. SS-20L-24V

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 BATTERIES

SOLAR SERIES
The SOLAR series batteries are especially designed for medium and
small performance solar applications. They use gelled electrolyte.

These batteries are ideal for their use in Marine Aids to Navigation
installations, as they allow deep discharges, do not emit any gases
and can be installed in any position, without disrupting their operation
when installed on buoys.

The advantages of the “maintenance-free” VRLA batteries are

enhanced by the worldwide excellent reputation and technical image
of the DRYFIT technology.

Their minimum discharge rate provides a high storage autonomy,

without recharge, up to 2 years.

Designed in accordance with IEC 61427 and IEC 60896-21/22

Standards.

FEATURES

√ DRYFIT technology ensuring a free-maintenance, gelled, leak-

proof battery.

√ Grid plate of high cycling performance: 800 cycles at 60%.

√ Nominal capacity from 6.6 to 230 Ah C 100 (20ºC).

√ Minimum operating service life of 5 years.

√ Completely recyclable due to the low CO2 footprint.

√ Possibility of storage without recharge up to 2 years.

√ Robust design resilient in harsh conditions.

√ Protection valves against over-pressures, protecting cells

against the atmosphere.

√ Proof against deep-discharge.

√ Easy installation.

√ Trouble-free transport: no restrictions for rail, road, sea and air

transportation (IATA, DGR clause A67).
 BATTERIES

SOLAR SERIES
Specifications subject to change without previous notice.

Type Nominal Nominal Length Width Height up to Height Approx. Terminal Terminal
voltage capacity max. max. top of cover including weight position
(V) C100 (mm) (mm) max. connectors (kg)
1.80 V/C (mm) max.
(Ah) (mm)

S12/6,6 S 12 6.6 152 65.5 94.5 98.4 2.6 S-4,8 3

S12/17 G5 12 17.0 181 76 - 167 6.1 G-M5 1
S12/27 G5 12 27.0 167 176 - 126 9.6 G-M5 1
S12/32 G6 12 32.0 197 132 160 184 11.1 G-M6 2
S12/41 A 12 41.0 210 175 - 175 14.6 A-Terminal 1
S12/60 A 12 60.0 261 136 208 230 19.0 A-Terminal 1
S12/85 A* 12 85.0 353 175 - 190 26.8 A-Terminal 1
S12/90 A 12 90.0 330 171 213 236 30.0 A-Terminal 2
S12/130 A 12 130.0 286 269 208 230 39.8 A-Terminal 4
S12/230 A 12 230.0 518 274 216 238 67.0 A-Terminal 3
(*) 400 cycles.

Capacities C1 - C100 (20ºC)

C1 C5 C10 C20 C100 Drawings with terminal position, terminal and torque.
Type
1.70 V/C 1.70 V/C 1.70 V/C 1.75 V/C 1.80 V/C
S12/6,6 S 2.9 4.6 5.1 5.7 6.6
S12/17 G5 9.3 12.6 14.3 15.0 17.0
S12/27 G5 15.0 22.1 23.5 24.0 27.0
S12/32 G6 16.9 24.4 27.0 28.0 32.0
S12/41 A 21.0 30.6 34.0 38.0 41.0
S12/60 A 30.0 42.5 47.5 50.0 60.0
S12/85 A 55.0 68.5 74.0 76.0 85.0
S12/90 A 50.5 72.0 78.0 84.0 90.0
S12/130 A 66.0 93.5 104.0 110.0 130.0
5Nm 6Nm 8Nm
S12/ 230 A 120.0 170.0 190.0 200.0 230.0
Extracted capacity as a % (according to IEC 896-2)

2,60
Charge voltage (V) by element

1) With switch regulator (two-step controller). 100

2,55 Charge on curve B (max. charge voltage) for 90

2,50 max. 2 hrs/day, then switch over to continuous 80

2,45
B charge - curve C. 70

A 60
2,40
C 2) Standard charge (without switching) - curve A. 50
2,35
40
2,30 3) Boost charge (equalizing charge with external 30
2,25 generator). 20

2,20 Charge on curve B for max. 5 hrs/month, then 10

-20 -10 0 +10 +20 +30 +40 +50 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500
switch over to curve C. No de cycles
Temperature ºC

Endurance in cycles according to IEC 986-2.

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 BATTERIES
SOLAR BLOC SERIES
Thanks to their high-resistance and reliability, the SOLAR BLOC
series batteries are ideal for their use in installations under the
harshest conditions.

Manufactured with high and proved DRYFIT technology. Electrolyte

is immobilized in gel form, assuring a completely free-maintenance
battery.

This range of batteries offered by Mediterráneo Señales Marítimas is

ideal for their use in Marine Aids to Navigation installations, as they
allow deep discharges, do not emit any gases and can be installed
in any position, without disrupting their operation when installed on
buoys.

Designed according to Standards IEC 61427 and IEC 60896-21/22

Standards.

FEATURES

√ DRYFIT technology ensuring a free-maintenance, gelled, leak-

proof battery.

√ Grid plate of exceptional cycling performance: 1.200 cycles at

60%.

√ Nominal capacity from 60 to 330 Ah C 100 (20ºC).

√ Minimum operating service life of 7 years.

√ Completely recyclable due to the low CO2 footprint.

√ Possibility of storage without recharge up to 2 years.

√ Robust design resilient in harsh conditions.

√ Protection valves against over-pressures, protecting cells

against the atmosphere.

√ Proof against deep-discharge.

√ Easy installation.

√ Trouble-free transport: no restrictions for rail, road, sea and air

transportation (IATA, DGR clause A67).
 BATTERIES

SOLAR BLOC SERIES

Specifications subject to change without previous notice.

Type Nominal Nominal Length Width Height up to Height Approx. Terminal Terminal
voltage capacity max. max. top of cover including weight position
(V) C100 (mm) (mm) max. connectors (kg)
1.80 V/C (mm) max.
(Ah) (mm)

SB12/60 A 12 60 278 175 - 190 19 A-Terminal 1

SB12/75 A 12 75 330 171 214 236 26.5 A-Terminal 2

SB12/100 A 12 100 513 189 195 223 36.5 A-Terminal 3

SB12/130 A 12 130 513 223 195 223 45.5 A-Terminal 3

SB12/185 A 12 185 518 274 216 238 62.5 A-Terminal 3

SB6/200 A 6 200 246 192 254 275 29 A-Terminal 4

SB6/330 A 6 330 312 182 337 359 47 A-Terminal 4

Capacities C1 - C100 (20ºC)

Drawings with terminal position, terminal and torque.
C1 C5 C10 C20 C100
Type
1.70 V/C 1.70 V/C 1.70 V/C 1.75 V/C 1.80 V/C
SB12/60 A 34 45 52 56 60

SB12/75 A 48 60 66 70 75

SB12/100 A 57 84 89 90 100

SB12/130 A 78 101 105 116 130

SB12/185 A 103 150 155 165 185

8Nm

SB6/200 A 104 153 162 180 200

SB6/330 A 150 235 260 280 330

Extracted capacity as a % (according to IEC 896-2)

2,60 1) With switch regulator (two-step controller). 100

Charge voltage (V) by element

2,55 Charge on curve B (max. charge voltage) for 90

2,50 max. 2 hrs/day, then switch over to continuous 80

B charge - curve C. 70
2,45
60
A
2,40
C
2) Standard charge (without switching) - curve A. 50
2,35 40

2,30 3) Boost charge (equalizing charge with external 30

2,25 generator). 20

2,20
Charge on curve B for max. 5 hrs/month, then 10
1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500
-20 -10 0 +10 +20 +30 +40 +50 switch over to curve C. No de cycles
Temperature ºC
Endurance in cycles according to IEC 986-2.

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 BATTERIES
A600 SOLAR SERIES
A600 SOLAR batteries offer the highest performance and reliability
under the harshest environmental conditions.

The electrolyte is fixed in gel, what guarantees the battery to be

completely maintenance free. In contrast to conventional batteries,
this type offers the advantage of an horizontal mounting. The required
room for the battery system can be minimized to one third.

This range of batteries offered by Mediterráneo Señales Marítimas is

ideal for their use in Marine Aids to Navigation installations, as they
allow deep discharges, do not emit any gases and can be installed in
small rooms or places without ventilation.

Designed according to Standards IEC 61427 and IEC 60896-21/22

Standards.

FEATURES

√ DRYFIT technology ensuring a free-maintenance, gelled, leak-

proof battery.

√ Robust tubular plates, optimising its for high corrosion resistance.

√ Exceptional cycling performance: 3,000 cycles at 60%.

√ Remarkable cost efficiency. 30% less overhead cost compared

to conventional batteries.

√ Nominal capacity from 294 to 3919Ah C 120 (20ºC).

√ Minimum operating service life of 15 years(20ºC).

√ Completely recyclable due to the low CO2 footprint.

√ Possibility of storage without recharge up to 2 years.

√ Screw connection for easy and safe assembly, maintenance

free, with excellent conductivity.

√ Protection valves against over-pressures, protecting cells

against the atmosphere.

√ Trouble-free transport: no restrictions for rail, road, sea and air

transportation (IATA, DGR clause A67).
 BATTERIES

A600 SOLAR SERIES

Specifications subject to change without previous notice.

Type Nominal Nominal Length Width Height up to Height Approx. Terminal Terminal
voltage capacity max. max. top of cover including weight position
(V) C100 (mm) (mm) max. connectors (kg)
1.85 V/C (mm) max.
(Ah) (mm)

A602/295 Solar 2 286 105 208 357 399 19 F-M8 1

A602/370 Solar 2 357 126 208 357 399 23 F-M8 1
A602/440 Solar 2 429 147 208 357 399 27 F-M8 1
A602/520 Solar 2 505 126 208 473 515 30 F-M8 1
A602/625 Solar 2 606 147 208 473 515 35 F-M8 1
A602/750 Solar 2 707 168 208 473 515 39 F-M8 1
A602/850 Solar 2 829 147 208 648 690 49 F-M8 1
A602/1130 Solar 2 1,105 212 193 648 690 66 F-M8 2
A602/1415 Solar 2 1,382 212 235 648 690 80 F-M8 2
A602/1695 Solar 2 1,658 212 277 648 690 95 F-M8 2
A602/1960C Solar 2 1,937 212 277 717 759 115 F-M8 2
A602/2600 Solar 2 2,547 216 400 775 816 160 F-M8 3
A602/3270 Solar 2 3,184 214 489 774 816 198 F-M8 4
A602/3920 Solar 2 3,821 214 578 774 816 238 F-M8 4

Capacities C1 - C120 (20ºC)

C1 C3 C5 C10 C100 C120
Drawings with terminal position, terminal and torque.
Type 1.67 1.75 1.77 1.80 1.85 1.85
V/C V/C V/C V/C V/C V/C
A602/295 Solar 123 167 193 218 286 294
A602/370 Solar 154 209 241 272 357 367
A602/440 Solar 185 251 290 326 429 440
A602/520 Solar 229 307 342 380 505 519
A602/625 Solar 275 369 410 456 606 623
A602/750 Solar 321 431 479 532 707 727
A602/850 Solar 367 513 626 681 829 848
A602/1130 Solar 489 684 834 908 1,105 1,131 20Nm
A602/1415 Solar 612 855 1,043 1,135 1,382 1,413
A602/1695 Solar 734 1,026 1,252 1,363 1,658 1,695
A602/1960C Solar 824 1,209 1,359 1,573 1,937 1,959
A602/2600 Solar 1,047 1,548 1,782 2,025 2,547 2,613
A602/3270 Solar 1,309 1,935 2,228 2,532 3,184 3,266
A602/3920 Solar 1,571 2,322 2,673 3,038 3,821 3,919
Extracted capacity as a % (according to IEC 896-2)

2,60 1) With switch regulator (two-step controller). 100

Charge voltage (V) by element

2,55 Charge on curve B (max. charge voltage) for 90

2,50 max. 2 hrs/day, then switch over to continuous 80

B charge - curve C. 70
2,45
60
A
2,40
C
2) Standard charge (without switching) - curve A. 50
2,35 40

2,30 3) Boost charge (equalizing charge with external 30

2,25 generator). 20

2,20
Charge on curve B for max. 5 hrs/month, then 10
1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500
-20 -10 0 +10 +20 +30 +40 +50 switch over to curve C. No de cycles
Temperature ºC
Endurance in cycles according to IEC 986-2.

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 WIND TURBINES

WINDSIDE
MSM offers its wide range of vertical wind turbines WINDSIDE as
ideal complement for battery charging, making wind energy into
electricity wherever energy is needed. They are specially suitable
for offshore installations, buoys, small islands, vessels, ..., under the
harshest marine conditions.

WINDSIDE wind turbines provide highest efficiency and durability

with a minimum maintenance.

One of the main advantage of its vertical axe construction is its

autocontrolled rotational speed, also in conditions of extreme wind.

Also characterised by their respect for the environment due to their

soundless (0 dB), ensuring a safe installation in population centres,
public spaces, natural areas, etc.

FEATURES

√ Vertical wind turbine based on sailing engineering principles.

√ The turbine rotor is rotated by two spiral-formed vanes.

√ Operating in harmony with nature and environment.

√ No need to stop or secure during storms.

√ No need to be turned to wind direction.

√ Stands snow, frost, heat and humidity.

√ Composite re-enforced fibre glass propellers.

√ Marine-grade aluminium generator casings.

√ Stainless-steel hardware.

√ Top quality lubricated bearings.

√ Depending on its use and the weather conditions, we offer

various models to ours customers.
 WIND TURBINES
WINDSIDE
WS-0,15B WS-0,30B WS-0,30A8 WS-2B WS-2AK
Specifications subject to change without previous notice.

WS-4B

WS-4A
Materials and environment

Fibre glass vanes.

Aluminium fixings.

Chrome coated steel or stainless steel shaft, depending on model.

Generator and generator end plates from marine grade aluminium or hot-dip
galvanized steel, depending on model.
Stainless-steel (A4 o A2) or hot-dip galvanized steel (Zn) bolts.

Produces maximum amount of energy in storms.

Soundless (0 dB), measured in 2 meters distance from the vane.

Long service life.

Minimum maintenance, only lubrication.

Safe to people, animals and nature.

MODEL WS-0.15B WS-0.30B WS-0.30A8 WS-2B WS-2AK WS-4B WS-4A

Weight 38 kg 46 kg 98 kg 550 kg 1,000 kg 800 kg 1,200 kg
Swept area 0,15 m2 0,30 m2 0,30 m2 2 m2 2 m2 4 m2 4 m2
Voltage 12/24V 12/24V 12/24V 12/24V 12/24V 12/24/48V 12/24/48V
Max. power 71/132W 97/190W 102/201W 420/792W 432/864W 420/840/1,632W 500/900/1,680W
Regulator WGU 22 WGU 22 WGU 22 WGU 25-50 WGU 25-50 WGU 50 WGU 50
Fixings 6 nos. M12 6 nos. M12 8 nos. M20-M16 8 nos. M30 20 nos. M20 8 nos. M30 8 nos. M30
Wind load 50 kg 100 kg 100 kg 500 kg 500 kg 1,000 kg 1,000 kg

Approximate annual power production / Annual average wind speeds (KWh/year)

m/s WS-0.15 WS-0.30 WS-2 WS-4

4 15 30 120 400
5 40 80 700 2,000
8 96 192 1,800 5,200
10 206 413 3,900 11,100

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 MARINE WIND GENERATORS

AEROGEN
AEROGEN marine wind generators are ideal for charging acid and
gel batteries when main power is either not available or not suitable,
both for regular and emergency uses.

These third generation wind generators are the result of years of

investigation and experience since 1982, manufactured and supplied
all over the world. In choosing your wind generator the key parameters
are output, power requirements and wind speeds.

Designed to work in an optimal way with win speeds between 5 and

20 knots. For more wind speeds, the generator provides a higher
performance, producing great power in a continuos and secure way.

The performance and efficiency of all wind generators have been

established by independent testing institutions.

FEATURES

√ Optimal operation with wind speeds between 5 and 20 knots.

√ High efficiency of brushless alternators.

√ Compact, light and solid design, for an easy installation and a

silent and safe harsh conditions.

√ Manufactured with high-quality materials and with protection

from marine harsh.

√ Minimum size with maximum power (thanks to its propeller

design).

√ Various models according to power required, from 0.5 to 30

amperes.

√ Available in 12 and 24V.

√ Conceived to work without interruptions.

√ Protected with a thermal device: production is autolimited

depending on the wind force.

√ Charge controller available to protect batteries.

√ Maintenance free.
 MARINE WIND GENERATORS

AEROGEN
Specifications subject to change without previous notice.

AERO6GEN

AERO4GEN AERO2GEN

MODEL SELECTION
POWER USED POWER GENERATED
AEROGEN
Amp/hour Weekly Amp/hour Weekly
MODEL
12V d.c. 12V d.c. (12 knots)
20-75 AERO2GEN 85
70-300 AERO4GEN 300
300-650 AERO6GEN 670

CURRENT/WIND SPEED

AMPS AERO2GEN AERO4GEN AERO6GEN

30 - - 45
20 - 60 30
15 - 40 23
WIND SPEED (KNOTS)

10 - 28 20
8 - 25 17
6 - 20 15
5 - 19 14
4 40 17 12
3 33 15 11
2 25 13 10
1 19 10 7,5
0,5 12 8 6,5

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 BATTERY CHARGERS
BLUEPOWER IP65/67

The BluePower Battery Chargers feature a microprocessor controlled

“adaptive” technology which controls the charge of the battery. The
“adaptive” features will automatically optimise the charging process
based on the battery duty cycle.

This charger is ideal for it use in Marine Aids to Navigation installations

as a power supply complement. Completely encapsulated in resin,
thus providing a high resistance under harsh humidity and salinity
conditions.

Adaptive 3- or 4-stage charge characteristic, depending on model.

FEATURES
√ Waterproof, ignition protected and shockproof:
- Water, hydrocarbons or dirt will not damage the charger.
- The enclosure is made from cast aluminium and the
electronics are moulded in resin.

√ Protected against overheating:

- Can be used in hot environment such as machine room,
battery boxes or maritime towers.
- Output current will be reduced when temperature increases
(up to 60°C), but the charger will not fail.

√ 92% efficiency or better. Once the battery is fully charged,

power consumption reduces to less than 1 Watt.

√ Adaptive 4-stage charge: bulk - absorption - float - storage.

The “adaptive” feature will automatically optimise the charging
process based on the battery duty cycle (12/7 model, 3-stage
charge).

√ Two LEDs for status indication:

- LED yellow: bulk charge.
- LED green: float mode, battery charged.
- LED yellow and green: absorption charge.

√ The “storage” mode prevents stratification of the electrolyte and

sulphation, major cause of early battery failure.
 BATTERY CHARGERS
BLUEPOWER IP65/67
Specifications subject to change without previous notice.

BLUE POWER CHARGER 12/7 12/17 12/25 24/8 24/12

Input voltage range and frequency 200-265V a.c. 180-265V a.c. 180-265V a.c. 180-265V a.c. 180-265V a.c.
45-65 Hz 45-65 Hz 45-65 Hz 45-65 Hz 45-65 Hz
Efficiency 92% 94% 92% 95% 93%
No load power consumption 0.5W 0.5W 0.5W 0.5W 0.5W
Charge voltage ‘absorption’ (V d.c.) 14.4 14.4 14.4 28.8 28.8
Charge voltage 'float' (V d.c.) 13.7 13.7 13.7 27.4 27.4
Charge voltage ‘storage’ (V d.c.) 13.2 13.2 13.2 26.4 26.4
Charge current (A) 7 17 25 8 12
Charge algorithm 3-stage with
18-hour limited 4-stage adaptive.
absorption.
Can be used as power supply ✓
Protections Battery reverse
polarity, short
Battery reverse polarity, short circuit, over temperature and transient overvoltage.
circuit and over
temperature.
Operating temp. range From -20° to +60°C (full rated output up to 40°C)
Humidity Up to 100%.

ENCLOSURE
Material & Colour Aluminium (blue RAL 5012)
Battery-connection Black and red cable of 1.5 m
230 V a.c.-connection Cable of 1.5 m with CEE 7/7 plug
Protection category IP 65 IP 67
Weight (kg) 1.1 2.4 2.4 2.4 2.4
Dimensions (mm) 43x80x155 99x219x65

STANDARDS
Safety EN 60335-1, EN 60335-2-29
Emission/Immunity EN 55014-1-2,
EN 55014-1, EN 61000-6-3, EN 61000-3-2
EN 60555-2-3

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 BATTERY CHARGERS

PHOENIX
The Phoenix Battery Chargers feature a microprocessor controlled
‘adaptive’ battery management system that can be preset to suit
different types of batteries. The ‘adaptive’ feature will automatically
optimise the process based on the battery duty cycle.

Adaptive 4-stage charge system: bulk – absorption – float – storage.

Three outputs, two complete and one of 4 amps.

Universal 90-265V input, 45-65 Hz.

FEATURES

√ Adaptive 4-stage charge: bulk - absorption - float - storage.

√ The right amount of charge: variable absorption time. To prevent overcharging of the battery, the
absorption time is kept short when only shallow discharges occur. After a deep discharge the
absorption time is automatically increased to make sure that the battery is completely recharged.

√ Every charger comes with a battery temperature sensor. When connected, charge voltage
will automatically decrease while increasing battery temperature. This feature is especially
recommended for gelled batteries and/or when important fluctuations of battery temperature are
expected.

√ Battery voltage sense, so that the battery always receives the correct charge voltage. This feature
allows to compensate voltage losses due to cable resistance.

√ Universal input voltage range: 90-265V a.c. and also suitable for d.c. supply.

√ The “storage” mode prevents stratification of the electrolyte and sulphation, major cause of early
battery failure.

√ Ready to communicate with a PC through its RS-485 serial port (wire not included).
 BATTERY CHARGERS

PHOENIX
Specifications subject to change without previous notice.

PHOENIX BATTERY CHARGER 12/30 12/50 24/16 24/25

Input voltage range (V a.c.) 90-265
Input voltage range (V d.c.) 90-400
Frequency (Hz) 45-65
Power factor 1
Charge voltage 'absorption' (V d.c.) 14.4 14.4 28.8 28.8
Charge voltage 'float' (V d.c.) 13.8 13.8 27.6 27.6
“Storage” voltage (V d.c.) 13.2 13.2 26.4 26.4
Charge current starter batt. (A) 4 4 4 4
Charge characteristic 4 stage adaptive
Battery capacity (Ah) 100-400 200-800 100-200 100-400
Temperature sensor ✓ ✓ ✓ ✓
Forced cooling ✓ ✓ ✓ ✓
Can be used as power supply ✓ ✓ ✓ ✓
Protections Output short-circuit, reverse polarity, over-temperature and transient overvoltage.
Operating temp. range De -20º a +60ºC
Humidity (non condensing) max. 95%

ENCLOSURE
Material & Colour Aluminium (blue RAL 5012)
Battery-connection M6 studs
230V a.c.-connection Screw-clamps 4 mm² (AWG 11)
Protection category IP 21
Weight (kg) 3.8
Dimensions (mm) 350x200x108

STANDARDS
Safety EN 60335-1, EN 60335-2-29
Emission/Immunity EN 55014-1, EN 61000-3-2
Vibration IEC68-2-6:10-150 Hz/1.0G

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com
 SOLAR CONTROL UNIT

SCU
SCU Solar Control Unit is an ideal device for its use in Aids to
Navigation solar installations of medium size or any other system.

SCU provides a total overvoltage, overcharge and deep discharge

protection of batteries, and also protects installation by interconnecting
solar modules, battery and charge.

The SCU unit integrates a precision meter, which checks the battery
state of charge.

It is equipped with protection devices against lightning, surge and

short-circuit protection of the installation.

FEATURES

√ Charge controller:
- This controller is responsible for controlling the battery
charging by using the solar power system.
- The drive has an up to 60 Amp capacity of current of the
photovoltaic array (FV) to 12, 24 or 48V.

√ Discharge controller:
- This controller has the function of controlling the discharge
of the battery, cutting the consumption current if the battery
voltage is too low.
- It prevents damages of the battery by over-discharges.

√ Battery display:
- LCD display allows to show the state of battery:
. Battery voltage (V).
. Charge and discharge current (A).
. Amp-hour counter (Ah).
. Battery state of charge (%).
- PC connexion to download historic data.

√ Overvoltage protection:
Located at solar module inputs to protect installation against
transient overvoltage caused by storms.
 SOLAR CONTROL UNIT
SCU
Specifications subject to change without previous notice.

MODELS
SPECIFICATIONS
SCU 4020 SCU 6030

Max. current charge 40 A 60A

Max. current discharge 20 A 30 A

Fuses: Battery 46 A (NH type) 63 A (NH type)
Solar modules 2 x 25 A (14 x 51 mm) 2 x 32 A (14 x 51 mm)
Common Negative.

Weight 25 kg 32 kg

Dimensions 54 x 43 x 20 cm 64 x 43 x 25 cm

Voltage 12/24V 12/24/48V

Temperature sensor External, optional.

Protections Over-currents, over-voltages and short-circuits.

Watertightness degree IP 66 (IEC 60529)

Battery temperature sensor Optional.

Indicators / Parameters
Battery voltage (V). Voltage disconnection.
Solar charge current (A). Current (A).
Operating current (A). Charge status (%).
Charge counter (Ah). Time-to-go (h): battery time-to-go with the current load.
Discharge counter (Ah). Temperature (ºC).
Disconnection alert from deep discharge.

Options
Charge controller with MPPT tracker system of maximum power.
ATEX versions for hazardous areas.
Stainless-steel housing.
Other powers and configurations available.

MEDITERRÁNEO SEÑALES MARÍTIMAS, S.L.L.

[email protected] • www.mesemar.com