Vx-Series Spares & Accessories Catalogue - Contents

Contents
Introduction ................................................................................................................... 2
Consumable Kits, Tools & Consumables ................................................................... 3
Consumables ........................................................................................................................................... 3
Vx-Series Spares ........................................................................................................... 6
Cassette ................................................................................................................................................. 10
Print Head Spares ................................................................................................................................ 13
Software ................................................................................................................................................. 16
Cables ........................................................................................................................... 17
Mains Cables ......................................................................................................................................... 18
Power Supply ........................................................................................................................................ 24
Vx PSU Clamp ...................................................................................................................................... 26
I/O Cable ............................................................................................................................................... 27
Encoder Assemblies .................................................................................................... 29
Encoder Assemblies ............................................................................................................................ 30
Printer Accessories ..................................................................................................... 33
Shim Kit.................................................................................................................................................. 34
V1/V2 Positive Air Kit ........................................................................................................................ 35
Vx Print Head Splash Cover ............................................................................................................. 36
User Interface .............................................................................................................. 37
Vx User Interface ................................................................................................................................ 38
Vx User Interface Mount Holster Assembly ................................................................................. 39
TouchPad Cables ................................................................................................................................. 41
User Interface Mount-Arm Assemblies .......................................................................................... 43
Mount Arm Adaptor Plate................................................................................................................. 45
Bracket Assemblies..................................................................................................... 47
Vx Economy Bracket .......................................................................................................................... 49
Vx L-Bracket Assemblies ................................................................................................................... 51
V1/V2 Window Bracket Assemblies ............................................................................................... 53
V3 Window Bracket Assemblies ...................................................................................................... 55
Labeller Bracket Web Positioning Roller Assemblies ................................................................. 59
Type A - Labeller Bracket Web Positioning Roller Assemblies ................................................ 60
Type B - Labeller Bracket Web Positioning Roller Assemblies ................................................ 64
Type C - Labeller Bracket Web Positioning Roller Assemblies ............................................... 68
Roller Assemblies ................................................................................................................................ 70
V-Series L-Bracket Assembly ............................................................................................................ 72
Labeller Bracket Assemblies ............................................................................................................. 73
Web Positioning Module Assemblies .............................................................................................. 75
Printer & Print Roller Mount Adaptor Kits - Domino Bracket Kits ........................................ 77
Printer & Print Roller Mount Adaptor Kits - Competitor Bracket Kits ................................. 79
OEM Brackets & Accessories ........................................................................................................... 84
Food Quality Rubber Print Roller Selection Table ...................................................................... 85
Bespoke Solutions ....................................................................................................... 87
Specialised Solutions ........................................................................................................................... 88
Notes ............................................................................................................................ 89

EPT071549 Issue 3, March 2024

Vx-Series Spares & Accessories Catalogue - Introduction

Introduction
This document provides useful information about the current Vx-Series spares, accessories
and brackets including photography, part numbers and descriptions.

For all Pin outs & wiring diagrams, please refer to the Product Manual on MyDomino.

Note: This is a working document and will be continuously updated; the newest version of
this document will always be available from MyDomino.

2 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Consumable Kits, Tools & Consumables

Consumable Kits,Tools &

Consumables
Consumables
Quantity
Image Description
per kit

EPT039697 1
Thermal Print Head Cleaning
Wipes (Box of 50)

Note: Used for cleaning

electrical contacts only, solvent
wipes can damage ink nozzles.

VPR0223 1
Cleaning Pens (Pack of 5)

EPT071549 Issue 3, March 2024 3

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

Quantity
Image Description
per kit

WJ-111 1
M-Series & V-Series Cleaning
Fluid 30ml

VEY0786 1
Air Tube Supply 3m, 6mm

VEY8492 1
Synthetic Grease, FS ‘Food Safe’
Extra 100g Tube

Ribbons
A wide range of Domino
Ribbons are available to suit all
printers’ requirements, please
contact your local Domino
Representatives.

4 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Consumable Kits, Tools & Consumables

Quantity
Image Description
per kit

VEY5151 1
Domino Printed Film (140mm)
1200m Reel

VEY5153 1
Clear Printing Film (140mm)

EPT071549 Issue 3, March 2024 5

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

1st, 2nd & 3rd Level Spares

1st Level Spares
Quantity
Image Description
per kit

8D32CA001DU 1
Vx50i/Vx150i 53mm Print Head
Kit

8D32CB001DU 1
Vx50i/Vx150i 32mm Print Head
Kit

2nd Level Spares

Quantity
Image Description
per kit

D02E3Z001 1
Vx50i/Vx150i Ball Lock Shaft
Assembly Spare

D01MVG001 1
Vx50i/Vx150i Ball Lock Shaft
Spare

6 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Vx-Series Spares

Quantity
Image Description
per kit

D01N52001 1
Vx Drive Belt Spare

D02E3X001 1
Vx50i/Vx150i Guide Roller
Spare

D02E41001 1
Vx Peel Off Roller Shaft Spare

D00SKX001 1
Vx Peel Off Roller Sleeve Spare

EPT071549 Issue 3, March 2024 7

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

Quantity
Image Description
per kit

D02E3W001 2
Vx50i/Vx150i Spindle Kit 55mm
Spare
2
D02E4C001
Vx50i/Vx150i Spindle Kit 34mm
Spare

D02Y27001 1
Vx50i/Vx150i Interface PCB
Spare

3rd Level Spares

Quantity
Image Description
per kit

D02Y28001 1
Vx50i/Vx150i PCB Flat Cable
Spare

D02ZZJ001 1
Vx50i/ Main PCB Spare

D02Y25001
Vx150i/ Main PCB Spare

8 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Vx-Series Spares

Quantity
Image Description
per kit

D02E45001 1
Vx150i PCB Spare

D02E4D001
Vx50i PCB Spare

D02E43001 1
Vx50i/Vx150i Print Head
Position Detect Spare

EPT071549 Issue 3, March 2024 9

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

Vx-Series Spares
Cassette
Quantity
Image Description
per kit

8D32AC001DU 1
Domino Vx150i Cassette -
53mm

8D32AD001DU 1
Domino Vx150i Cassette -
32mm

8D32AB001DU 1
Domino Vx50i Cassette

D02E3Y001 1
Vx50i/Vx150i Internal Ribbon
Encoder Roller Spare

10 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Vx-Series Spares

Quantity
Image Description
per kit

D02E46001 2
Vx50i/Vx150i Ribbon Motor
Assembly Spare

D02E47001 1
Vx50i/Vx150i Horizontal Motor
Assembly Spare

D02E48001 1
Vx50i/Vx150i Vertical Motor
Assembly Spare

D01SDF001 1
Vx50i/Vx150i Cassette
Detection Switch Spare

EPT071549 Issue 3, March 2024 11

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

Quantity
Image Description
per kit

D01VKB001 1
Vx50i/Vx150i (Programmed) SD
Card Spare

Note: Pre-programmed SD
Card with the latest firmware

EPT068324 1
Vx50i/Vx150i Narrow Ribbon
Spacers 34 to 22mm, White
(Pack of 2) Spare

EPT068325 1
Vx50i/Vx150i Narrow Ribbon
Spacers 55 to 34mm, Black
(Pack of 2) Spare

12 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Vx-Series Spares

Print Head Spares

Quantity
Image Description
per kit

D02E40001 1
Vx50i/Vx150i Print Head
Carriage Assembly Spare

D02CFL001 1
Vx50i/Vx150i Print Head Cable
Assembly Spare

D01NBG001 1
Vx Print Head Clip Spare

D02E42001 1
Vx50i/Vx150i Print Head Push
Arm Assembly Spare

EPT071549 Issue 3, March 2024 13

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

Quantity
Image Description
per kit

D02E44001 1
Vx50i/Vx150i Print Head Sensor
Kit Spare

8D32AF001DU 1
Vx50i/Vx150i Print Head Angle
Blocks (x3) Spare

D02E49001 1
Vx50i/Vx150i Print Head
Standard Angle Block Spare

D02E4A001 1
Vx50i/Vx150i Thermal Transfer
Sheet Kit Spare

14 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Vx-Series Spares

Quantity
Image Description
per kit

D02E4B001
Vx50i/Vx150i Fastener Kit Spare

Kit Components
Pan Head Screw M3 x 6 2448B 9
Pan Head Screw M3 x 14 2448B 4
Bolt Screw M3 x 8 3
TRX Botton Screw M3 x 6 7
2448B
Screw Flat Low Head TRX M3 x 6
6
Washer Plain S 3 1

EPT071549 Issue 3, March 2024 15

Vx-Series Spares & Accessories Catalogue - Vx-Series Spares

Software
The Serialisation Pack enables the Dynamark
buffer commands and allows fast item level
EPT075318 - Vx150i Validation Pack serialisation. The rest of the Dynamark
commands are available to use without the
pack.

The Advanced Security Pack enables the

EPT075319 - Vx150i Advanced Security functionality to create and manage users
Pack (usernames, passwords and policy) locally on
the Gx.

The Promotional Coding Pack enables data

from a USB drive to populate one or more
EPT075321 - Gx Promotional Coding
text fields. Promotional Coding is an option
Pack
for all controllers (Gx150i, Gx350i and Gx-
OEM).

16 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Cables

Cables
Mains Cables ................................................................................................................ 18
Mains Cable 2.0m IEC Euro - EPT060866 ..................................................................................... 18
Mains Cable 2.0m IEC UK - EPT060865 ........................................................................................ 19
Mains Cable 2.0m IEC US - EPT026724 ......................................................................................... 20
Mains Cable 2.0m IEC China - EPT026722.................................................................................... 21
Mains Cable 2.0m IEC Aus/Nz - EPT053520................................................................................. 22
Mains Cable 2.0m IEC No Plug - 78055 ......................................................................................... 23

Power Supply ............................................................................................................... 24

FSP180-AAAN3, Switching Power Adaptor, No AC Cable - EPT071214 ............................. 24
FSP180-AAAN3, Switching Power Adaptor, India AC Cable - EPT071215........................... 25

Vx PSU Clamp............................................................................................................. 26
PSU Clamp Vx - EPT068870 ............................................................................................................. 26

I/O Cable ...................................................................................................................... 27

V-Series I/O Cable 5m - EDP002215SP.......................................................................................... 27

EPT071549 Issue 3, March 2024 17

Vx-Series Spares & Accessories Catalogue - Cables

Mains Cables
Product Technical Data
• 2m Cable
Mains Cable 2.0m IEC Euro -
EPT060866

Description: European power lead for the

brick PSU.
Image / Diagram

18 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Cables

Product Technical Data

• 2m Cable
Mains Cable 2.0m IEC UK -
EPT060865

Description: UK power lead for the brick

PSU.
Image / Diagram

EPT071549 Issue 3, March 2024 19

Vx-Series Spares & Accessories Catalogue - Cables

Product Technical Data

• 2m Cable
Mains Cable 2.0m IEC US -
EPT026724

Description: US power lead for the brick

PSU.
Image / Diagram

20 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Cables

Product Technical Data

• 2m Cable
Mains Cable 2.0m IEC China -
EPT026722

Description: China power lead for the

brick PSU.
Image / Diagram

EPT071549 Issue 3, March 2024 21

Vx-Series Spares & Accessories Catalogue - Cables

Product Technical Data

• 2m Cable
Mains Cable 2.0m IEC Aus/Nz -
EPT053520

Description: Aus/Nz power lead for the

brick PSU.
Image / Diagram

22 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Cables

Product Technical Data

• 2m Cable
Mains Cable 2.0m IEC No Plug -
78055

Description: Open ended power lead for

the brick PSU.
Image / Diagram

EPT071549 Issue 3, March 2024 23

Vx-Series Spares & Accessories Catalogue - Cables

Power Supply
Product Technical Data
• AC Input: 100-240V~, 2.0A, 50-60Hz
FSP180-AAAN3, Switching • DC Output: 24V
Power Adaptor, No AC Cable -
EPT071214

Description: Power Supply for all regions

excluding India.

Image / Diagram

24 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Cables

Product Technical Data

• AC Input: 100-240V~, 2.0A, 50-60Hz
FSP180-AAAN3, Switching • DC Output: 24V
Power Adaptor, India AC Cable -
EPT071215

Description: Power supply for India only.

Image / Diagram

EPT071549 Issue 3, March 2024 25

Vx-Series Spares & Accessories Catalogue - Cables

Vx50i/Vx150i PSU Clamp

Product Technical Data
• Stainless steel clamp.
Vx50i/Vx150i PSU Clamp Spare - • Suitable for clamping PSU’s which
EPT068870 are 76mm wide x 25.5 high.
• Two mount holes available on
Description: This clamp is used for mounting side flanges for M6 screws.
the Vx PSU’s securely to flat surfaces rather than Screws to be provided by
using cable-ties or other means of mounting. installation engineer and length
specified to suit the particular
installation.
Image/ Diagram

Connection/ Fitting BOM

1x PSU Clamp.

26 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Cables

I/O Cable
Product Technical Data
• 5 metre cable
V-Series I/O Cable 5m - • 15 pin connection
EDP002215SP

Description: This I/O cable is used for

integration between the I/O box and host
machine.
Image/ Diagram

EPT071549 Issue 3, March 2024 27

Vx-Series Spares & Accessories Catalogue - Cables

28 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – OEM Brackets & Accessories

Encoder Assemblies
Encoder Assemblies .................................................................................................... 30
Vx Encoder and Spring-Loaded Bracket Assembly – EPT069181 ............................................ 30
Vx Encoder Assembly – EPT069724 ............................................................................................... 31

EPT071549 Issue 3, March 2024 29

Vx-Series Spares & Accessories Catalogue - OEM Brackets & Accessories

Encoder Assemblies
Product Technical Data
• Encoder is supplied fully assembled to
Vx Encoder and Spring-Loaded a spring-loaded bracket with a 5m
Bracket Assembly – EPT069181 cable and terminated with a 9-Pin D-
Sub male connector.
Description: This encoder assembly is used • Encoder: 2000ppr, 7-30V supply, 5V
for mounting onto the various TTO CM RS422 output.
brackets in Vx CM applications. • Encoder wheel outside diameter –
The encoder assembly fits directly onto 51.8 mm.
existing M6 mount holes on the TTO • The Vx encoder is not compatible
brackets and the encoder wheel runs on the with the V-Series printers, however it
outer diameter (46mm) of the standard can be mounted to the V-Series
Domino print roller. brackets.
• The torsion springs on the bracket
can be adjusted to achieve suitable
wheel loading on the print roller.
Image/ Diagram

Connection/ Fitting BOM

1x Encoder mount shaft.
1x encoder crank arm.
2 x Set Collars.
1x RH torsion spring.
1x LH torsion spring.
1x Vx encoder assy (EPT069724).
1 x Encoder wheel.
1 x Wheel o-ring.
Fasteners.

30 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – OEM Brackets & Accessories

Product Technical Data

• The encoder is supplied fully
Vx Encoder Assembly – assembled with a 5m cable and
EPT069724 terminated with a 9-Pin D-Sub male
connector.
Description: This encoder assembly is used • Encoder: 2000ppr, 7-30V supply, 5V
on part EPT069181 (Vx encoder with spring- RS422 output.
loaded mount bracket). This encoder • Encoder shaft diameter – 8mm.
assembly is a separate orderable part when • The Vx encoder is not compatible
needing to replace the Vx encoder only with the V-Series printers, however it
(without mount bracket) in existing can be mounted to the V-Series
installations or in applications where the user brackets which already have encoder
manufactures their own encoder mount mount brackets.
bracket.
Image/ Diagram

Connection/ Fitting BOM

1x Vx Encoder Assembly (EPT069724).

EPT071549 Issue 3, March 2024 31

Vx-Series Spares & Accessories Catalogue - OEM Brackets & Accessories

32 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Printer Accessories

Printer Accessories
Shim Kit ....................................................................................................................... 34
V1/V2 Shim Kit - 0.5mm/1mm/1.5mm/2mm - EAS002629 ........................................................ 34

V1/V2 Positive Air Kit ................................................................................................. 35

V1/V2 Positive Air Kit - EAS002970 ............................................................................................... 35

Vx Print Head Splash Cover ...................................................................................... 36

Vx Print Head Splash Proof Cover Assembly - EPT077998 ...................................................... 36

EPT071549 Issue 3, March 2024 33

Vx-Series Spares & Accessories Catalogue – Printer Accessories

Shim Kit
Product Technical Data
• Aluminium Shims.
V1/V2 Shim Kit - • Supplied in thicknesses of 0.5mm, 1mm,
0.5mm/1mm/1.5mm/2mm - 1.5mm and 2mm.
EAS002629 • Inserted between printer carrier (on
window brackets, L-Brackets & Labeller
Description: This V1/V2 shim kit can Brackets) and printer mount pad.
also be used to obtain the correct print
distance between the Vx printer housing
lower-surface and the IM platen or CM
print roller. These shims are mostly used
for setup in applications such as mounting
the printers to competitor or bespoke
printer brackets where exact print gaps
are uncertain.
Image/ Diagram

BOM Notes
1x 0.5mm Shim This kit is not supplied as
1x 1mm Shim standard with Vx150i
1x 1.5mm Shim printers.
1x 2mm Shim

34 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Printer Accessories

V1/V2 Positive Air Kit

Product Technical Data
• This air kit would be used in harsh
V1/V2 Positive Air Kit - environments.
EAS002970 • The supplied pneumatic fitting is
mounted directly to a port inside the
Description: This kit can also be used printer housing and with a tube grommet
for supplying a positive air pressure to the fitted to the rear cover.
internal volume of the Vx printers in • The regulator assembly with the mount-
order to reduce the ingress of dust and bracket can be assembled to the printer
vapour from the surrounding bracket or to a convenient position on
environment. the customer machine.

Image/ Diagram

BOM Notes
1x M4-4mm tube fitting This kit is not supplied as
1x 6mm-4mm tube fitting standard with Vx150i
1x regulator assembly printers.
0.3m long air supply tube 4mm
0.5m long air supply tube 6mm
1x grommet 4mm 6PH 4mm ID 1mm 6PNL

EPT071549 Issue 3, March 2024 35

Vx-Series Spares & Accessories Catalogue – Printer Accessories

Vx50i/Vx150i Print Head Splash Cover

Product Technical Data
• Red anodised aluminium cover with acetal
Vx50i/Vx150i Print Head guide strips.
Splash Proof Cover Assembly - • The grooves on the acetal guide-strips slide
EPT077998 into the lower profile of the printer cover.
• Warning text has been added to the cover
Description: This splash cover slides to remind the operator to remove the
into the underside opening of the Vx front cover before printing.
cover and provides general protection
from accidental splashing of liquids during Note: This cover is not supplied as standard
washdown carried out in close proximity with Vx printers and is not IP rated.
to the printer. The printer front cover
needs to be removed in order to fit the
splash cover. The splash cover is red
anodised and provides a visual reminder
to the operator that it is fitted to the
printer.
Image/ Diagram

36 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – User Interface

User Interface
Vx User Interface ........................................................................................................ 38
7 Inch TouchPad with 3m Cable - 8D32AA001DU .................................................................... 38

Vx User Interface Mount Holster Assembly ............................................................ 39

Vx User Interface Mount Holster Assembly - EPT075184 ........................................................ 39

TouchPad Cables ........................................................................................................ 41

Display Cable, USB C to A 5m - 8D32AE001DU ........................................................................ 41

User Interface Mount-Arm Assemblies.................................................................... 43

Long Mount-Arm Kit - EPT014751 ................................................................................................. 43
Short Mount-Arm Kit - EPT014752 ................................................................................................ 44

Mount Arm Adaptor Plate ......................................................................................... 45

Mount Arm Adaptor Plate - EPT043396........................................................................................ 45

EPT071549 Issue 3, March 2024 37

Vx-Series Spares & Accessories Catalogue - User Interface

Vx User Interface
Product Technical Data
• 7” full colour touch screen (800 x
7 Inch TouchPad with 3m Cable - 480 resolution).
8D32AA001DU • IP4x equivalent protection.
• Powered via USB connection.
Description: This is the human-machine- • Linux operating system.
interface to control the operations of the Vx • Connectivity: Printer side USB type
printer. C, Touchpad side USB type A
• Size: W 220mm x H 150mm x D
35mm
• Weight 0.6 Kg.
Image/ Diagram

38 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – User Interface

Vx50i/Vx150i User Interface Mount Holster Assembly

Product Technical Data
• Various hole configurations
Vx50i/Vx150i User Interface (including VESA 75 mount holes)
Mount Holster Assembly - and fasteners are provided to
EPT075184 mounting the holster directly to
brackets, arms & customer
equipment.
Description: This holster is used for
• The Vx TouchPad is simply inserted
mounting the 7 Inch Vx TouchPad
& extracted from the top of the
(8D32AA001DU) onto TTO brackets,
holster by hand.
mount arms or customer equipment.
• Holster material: ABS/PC
compound.
Note: For further installation details, see • Cutout on underside of holster for
Installation Drawing EPT074957 on cables access.
MyDomino portal.
Image/ Diagram

Connection/ Fitting

EPT071549 Issue 3, March 2024 39

Vx-Series Spares & Accessories Catalogue - User Interface

40 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – User Interface

TouchPad Cables
Product Technical Data
• 3m Cable
Vx50i/Vx150i Display Cable, USB • USB C to USB A
C to A 3m - D025YX001

Description:

Image/ Diagram

EPT071549 Issue 3, March 2024 41

Vx-Series Spares & Accessories Catalogue - User Interface

Product Technical Data

• 5m Cable
Vx50i/Vx150i Display Cable, USB • USB C to USB A
C to A 5m - 8D32AE001DU

Description:

Image/ Diagram

42 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – User Interface

User Interface Mount-Arm Assemblies

Product Technical Data
• Provides long reach and high
Long Mount-Arm Kit - EPT014751 adjustability.
• VESA 75 screen mount.
Description: This adjustable mount-arm can be • Supplied as a kit and assembled on
used for mounting the Vx User Interface to any site.
flat surface on customer machines. • Aluminium tube lengths can also
be cut down to suit application.
Note: The User Interface shown in image is for • The optional Vx UI holster
reference only and not included in the kit. EPT075185 can also be fitted
directly to this arm if regular UI
removal is required.
Image/ Diagram

Connection/ Fitting Notes

See also original CB72 for
further details.

EPT071549 Issue 3, March 2024 43

Vx-Series Spares & Accessories Catalogue - User Interface

Product Technical Data

• Provides shorter reach and less
Short Mount-Arm Kit - EPT014752 adjustability.
• VESA 75 screen mount.
Description: This adjustable mount-arm is used • Supplied as a kit and assembled on
for mounting the Vx User Interface to any flat site.
surface on customer machines. • Aluminium tube lengths can also
be cut down to suit application.
Note: The User Interface shown in image is for • The optional Vx UI holster
reference only and not included in the kit. EPT075185 can also be fitted
directly to this arm if regular UI
removal is required.

Image/ Diagram

Connection/ Fitting Notes

See also original CB72 for
further details.

44 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – User Interface

Mount Arm Adaptor Plate

Product Technical Data
• Kit includes screws for assembling the UI
Mount Arm Adaptor Plate - mount arms as well as screws for
EPT043396 mounting directly to the window/L-
brackets.
Description: This mount plate assembly is • Materials – 15mm thick anodised
used for mounting the standard Domino aluminium plate and stainless steel
User Interface mount-arms (EPT014751 & screws.
EPT014752) onto V-Series window or L- • 2x mount holes at 80mm pitch for
brackets, Vx L-brackets or any other mounting the plate to window/L-brackets
bespoke brackets which can be adapted for (M6 screws included)
mounting this kit.
Image/ Diagram

Connection/ Fitting BOM

6 x Screw M6 x 20
4 x M6 Flat Washer
1 x TouchPanel Mount Plate

EPT071549 Issue 3, March 2024 45

Vx-Series Spares & Accessories Catalogue - User Interface

46 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Bracket Assemblies
Vx Economy Bracket .................................................................................................. 49
Bracket Assembly Economy 0.7m IM Wide - EPT069625 ......................................................... 49
Bracket Assembly Economy 0.7m CM - EPT069686................................................................... 50

Vx L-Bracket Assemblies ........................................................................................... 51

0.9m Vx CM L-Bracket Assembly Side Mount - EPT066241 ..................................................... 51
0.9m Vx IM L-Bracket Assembly Side Mount - EPT066357 ....................................................... 52

V1/V2 Window Bracket Assemblies ......................................................................... 53

0.9m V1/V2 IM Bracket Assembly - EAS002706 .......................................................................... 53
0.9m CM Bracket Assembly - Order EAS002717 (Basic 0.9m Bracket Module) and Print
Roller as per BOM .............................................................................................................................. 54

V3 Window Bracket Assemblies ............................................................................... 55

0.9m V3 IM Bracket Assembly - Order 5-0460259 (Basic 0.9m Bracket Module) and 5-
0460007 (0.9m IM Platen Module) .................................................................................................. 55
0.9m V3 CM Bracket Assembly - Order 5-0460259 (Basic 0.9m Bracket Module) and all
CM components as per BOM ........................................................................................................... 56
1.4m V3 IM Bracket Assembly - Order 5-0460262 (Basic 1.4m Bracket Module) and 5-
0460276 (1.4m Platen Module) ........................................................................................................ 57
1.4m V3 CM Bracket Assembly - Order 5-0460262 (Basic 1.4m Bracket Module) and all
CM components as per BOM ........................................................................................................... 58

Labeller Bracket Web Positioning Roller Assemblies ............................................ 59

V1, V2 & V3 Labeller Bracket Web Positioning Roller Assemblies ......................................... 59

Type A - Labeller Bracket Web Positioning Roller Assemblies ............................ 60

V3 Roller Mount Assembly, Adjustable, 160mm, Type A - EAS001597 ................................. 60
V3 Roller Mount Assembly, Adjustable, 210mm, Type A - EAS002091 ................................. 61
V1/V2 Roller Mount Assembly, Adjustable, 160mm, Type A - EAS002409 ........................... 62
V1/V2 Roller Mount Assembly, Adjustable, 210mm, Type A - EAS002411 ........................... 63

Type B - Labeller Bracket Web Positioning Roller Assemblies ............................ 64

V3 Roller Mount Assembly, Fixed, 160mm, Type B - EAS001601 ........................................... 64
V3 Roller Mount Assembly, Fixed, 210mm, Type B - EAS002092 ........................................... 65
V1/V2 Roller Mount Assembly, Fixed, 160mm, Type B - EAS002410 ..................................... 66
V1/V2 Roller Mount Assembly, Fixed, 210mm, Type B - EAS002412 ..................................... 67

Type C - Labeller Bracket Web Positioning Roller Assemblies ............................ 68

V1/V2/V3 Roller Extension Plate Assembly, Adjustable, 160mm, Type C - EAS001604 .... 68
V1/V2/V3 Roller Extension Plate Assembly, Adjustable, 210mm, Type C - EAS002093 .... 69

Roller Assemblies ........................................................................................................ 70

Roller Assembly, 160mm, Spare - EAS001927.............................................................................. 70
Roller Assembly, 210mm, Spare - EAS001928.............................................................................. 71

EPT071549 Issue 3, March 2024 47

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

V-Series L-Bracket Assembly .................................................................................... 72

0.9m V-Series CM L-Bracket Assembly - Order of 5-0460012 (Basic 0.9m Bracket
Module) and all additional CM components as per BOM .......................................................... 72

Labeller Bracket Assemblies ..................................................................................... 73

V1/V2 Labeller Bracket Assembly - EAS001626 ........................................................................... 73
V3 Labeller Bracket Assembly - EAS001568 ................................................................................. 74

Web Positioning Module Assemblies ....................................................................... 75

0.9m Web Positioning Module Assembly - 5-0460281 ............................................................... 75
1.4m Web Positioning Module Assembly - 5-0460275 ............................................................... 76

Printer & Print Roller Mount Adaptor Kits - Domino Bracket Kits ...................... 77
Printer Carrier Assembly, Quick Release, V1/V2 - EPT006141 ............................................... 77
Adaptor Plate Kit, V-Series Window & L-Brackets - EAS002346 ............................................ 78

Printer & Print Roller Mount Adaptor Kits - Competitor Bracket Kits ............... 79
Adaptor Plate Kit - Markem SD - EAS002226 .............................................................................. 79
Adaptor Bush Kit, Print Roller Shaft, 16mm DIA, Markem/VideoJet - EPT005445 ............. 80
Adaptor Plate Kit, Markem S18-L - EAS002586 ........................................................................... 81
Adaptor Plate Kit, VideoJet DF - EAS002559 ............................................................................... 82
Adaptor Plate Kit, VideoJet 6210-W - EAS002634 .................................................................... 83

OEM Brackets & Accessories .................................................................................... 84

Ishida Atlas Adaptor Plate Kit - EPT045886.................................................................................. 84

Food Quality Rubber Print Roller Selection Table ................................................. 85

48 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Vx Economy Bracket
Product Technical Data
• Supplied in a flat-pack and assembled
Bracket Assembly Economy 0.7m on customer or channel site.
IM Wide - EPT069625 • Stainless steel support bars can be
cut to required width or longer bars
Description: This intermittent motion pillar can be added to suit application.
bracket assembly can be used for mounting • Acetal printer carrier and IM platen.
Vx printers onto customer packaging • Film guide-rollers not included but
machines. The printer can be mounted at 0 can be ordered separately and cut to
degree or 90 degree orientations. length (5-0460004 for 0.9m roller).
• Mounting Block Kit 5-0460019 (pack
of 2 with fasteners) can be ordered
separately.
Image/ Diagram - EPT069625

Connection/ Fitting BOM

Bracket Assembly EPT069625:
2x Support Bar Top.
2x Support Bar Bottom-IM.
4x 20mm Dia x 700mm St St Shaft.
4x 16mm Dia x 188.5mm St St Shaft.
1x Printer Carrier Assy.
1x IM Platen Assy (for spare rubber pad
order: 5-0460257).
2x M5 Thumb Knob.
Fasteners.
(Film guide rollers shown for reference only).

EPT071549 Issue 3, March 2024 49

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and assembled
Bracket Assembly Economy 0.7m on customer or channel site.
CM - EPT069686 • Stainless steel support bars and print-
roller shaft can be cut to required
Description: This continuous motion pillar width. Or longer bars and shaft can
bracket assembly can be used for mounting be added to suit application.
Vx printers onto customer packaging • Acetal printer carrier.
machines. • Film guide-rollers not included but
can be ordered separately and cut to
length (5-0460004 for 0.9m roller).
• Vx encoder assembly not included
and to be ordered separately (order
part EPT069181 for encoder with
mount bracket).
• Mounting Block Kit 5-0460019 (pack
of 2 with fasteners) can be ordered
separately.
Image/ Diagram

Connection/ Fitting BOM

Bracket Assembly EPT069686:
2x Support Bar Top
2x Support Bar Bottom-CM
2x 20mm Dia x 700mm St St Shaft
4x 16mm Dia x 188.5mm St St Shaft
1x 12mm Dia x 700mm St St Shaft
2x 12mm Shaft-Collar
1x Printer Carrier Assy
Fasteners

CM print roller to be ordered separately

(See Print Roller Selection Table)

50 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Vx L-Bracket Assemblies
Product Technical Data
• Supplied in a flat-pack and
0.9m Vx CM L-Bracket Assembly Side
assembled on site.
Mount - EPT066241 • Stainless steel support tubes
and aluminium guide rollers
Description: This continuous L-bracket assembly is can be cut down to any width
used for mounting Vx printers directly from their as required.
side-faces by making use of their two M6 side-
• Support tubes, guide rollers
mount holes.
and axle kit are available as
This L-bracket provides a very low-profile assembly
spares.
enabling fitting into tight spaces on customer
• Vx encoder assembly not
machines.
included and to be ordered
Note: When fitting the Vx printer, remove separately (order part
protective plug-screws from the side-mount holes EPT069181 for encoder with
on the printer housing. mount bracket).
• Correct rubber print roller
For further installation details, see Installation length to be selected as
Drawing EPT071778 on MyDomino portal. required by application.
• Mounting Block Kit 5-0460019
(pack of 2 with fasteners) can
be ordered separately.
Image/ Diagram - EPT066241

Connection/ Fitting BOM

2x End Plate Kits (EPT066260).
2 x 0.9m Stainless Steel Tube Assemblies
(5-0460003) – To support printer carrier.
2 x 0.9m Aluminium Guide Roller Assemblies
(5-0460004).
1 x Printer Carrier Assembly-Vx (EPT066243).
1 x 0.9m CM Axle Kit (5-0460277).

CM print roller to be ordered separately:

(See Print Roller Selection Table)

EPT071549 Issue 3, March 2024 51

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and
0.9m Vx IM L-Bracket Assembly Side assembled on site.
Mount - EPT066357 • Stainless steel support tubes
and aluminium guide rollers
Description: This intermittent L-bracket assembly can be cut down to any width
is used for mounting Vx printers directly from their as required.
side-faces by making use of their two M6 side-
• Support tubes and IM platen
mount holes.
assembly are available as
This L-bracket provides a very low-profile assembly
spares.
enabling fitting into tight spaces on customer
• Additional guide rollers (5-
machines.
0460004) can be ordered and
fitted.
Note: When fitting the Vx printer, remove
protective plug-screws from the side-mount holes • Self-adhesive rubber print pad
on the printer housing. available as a spare part (order
part 5-0460257).
For further installation details, see Installation • Mounting Block Kit 5-0460019
Drawing EPT071779 on MyDomino portal. (pack of 2 with fasteners) can
be ordered separately.
Image/ Diagram - EPT066357

Connection/ Fitting BOM

2x End Plate Kits (EPT066358).
1 x Printer Carrier Assembly-L (EPT066243).
2 x 0.9m Stainless Steel Tube Assemblies
(5-0460003) – To support printer carrier.
2 x 0.9m Aluminium Guide Roller Assemblies
(5-0460004).
1 x 0.9m Platen Assembly (5-460008) – Includes
a platen kit + two support tubes).

52 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

V1/V2 Window Bracket Assemblies

Product Technical Data
• Supplied in a flat-pack and
0.9m V1/V2 IM Bracket Assembly assembled on site.
- EAS002706 • Stainless steel support tubes and
aluminium guide rollers can be
Description: This intermittent window cut down to any width as
bracket assembly can be used for mounting required.
Vx printers onto customer packaging • Additional printer carrier, IM
machines. platen, rubber kit and guide
This bracket is suitable for mounting the Vx rollers are available separately.
at 0 degree orientation but not 90 degree
orientation. For mounting at 90 deg Note: To mount the Vx printers to this
orientation, see drawing “5-0410029-Mod” bracket, the engineer must use 4 x M6x16
for local printer-carrier modification. St St socket head cap screws as the
existing carrier screws are too long.
Image/ Diagram

BOM Notes
0.9m IM Bracket Assembly (EAS002706): See also CB29 for bracket
2x Window End Plates (5-0410002) construction configuration
2 x 0.9m Stainless Steel Tube Assemblies (5-0460003) details and part numbers
2 x 0.9m Aluminium Guide Roller Assemblies (5-0460004).
1 x Printer Carrier Assembly (5-0460258) – Note: printer Additional End Plate Kit -
carrier to be modified for rotating Vx printer by 90 deg. EPT040910 available to
1x Mounting Block Kit – Pack of 2 (5-0460019). order (consists of 2 x
1 x 0.9m IM Platen Assembly (5-0460007) – includes IM standard end plates with
platen kit + two support tubes. fasteners)

EPT071549 Issue 3, March 2024 53

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and
0.9m CM Bracket Assembly - Order assembled on site.
EAS002717 (Basic 0.9m Bracket • Stainless steel support tubes and
Module) and Print Roller as per aluminium guide rollers can be cut
BOM down to any width as required.
• Additional printer carrier, rubber
print-roller kit, axle kit, encoder
Description: This continuous window bracket
assembly and guide rollers are
assembly can be used for mounting Vx printers
available separately.
onto customer packaging machines.
• Correct rubber print roller length
Note: The encoder included on this bracket
to be selected as required by
cannot be used and would need to be replaced
application.
with a Vx encoder (EPT069724). The Vx
encoder would need to be separately ordered.
Note: To mount the Vx printers to this
The existing encoder mount bracket can be re-
bracket, the engineer must use 4 x M6x16
used for mounting the Vx encoder.
St St socket head cap screws as the
Note: Rubber Print Roller (See BOM) must be
existing carrier screws are too long.
ordered separately.
Image/ Diagram

BOM Notes
0.9m Bracket Module (EAS002717): See also CB29 for bracket
2x Window End Plates (5-0410002) construction configuration
2 x 0.9m Stainless Steel Tube Assemblies (5-0460003) details and part numbers
2 x 0.9m Aluminium Guide Roller Assemblies (5-0460004)
1 x Printer Carrier Assembly (5-0460258) Additional End Plate Kit -
1x Mounting Block Kit – Pack of 2 (5-0460019) EPT040910 available to
1 x 0.9m CM Axle Kit (5-0460277) order (consists of 2 x
1 x Encoder Assembly (5-0460011) Note: existing encoder standard end plates with
to be replaced with Vx encoder EPT069724. fasteners)
Incl. Fasteners

CM Components:
1x Rubber Print Roller (See Print Roller Selection Table)

54 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

V3 Window Bracket Assemblies

Product Technical Data
• Supplied in a flat-pack and assembled
0.9m V3 IM Bracket Assembly - on site.
Order 5-0460259 (Basic 0.9m • Stainless steel support tubes and
Bracket Module) and 5-0460007 aluminium guide rollers can be cut
(0.9m IM Platen Module) down to any width as required.
• Additional printer carrier, IM platen,
rubber kit and guide rollers are
Description: This intermittent window
available separately.
bracket assembly can be used for mounting
Vx printers with adaptor EAS002346 onto
Note: To mount the Vx printers to this
customer packaging machines. This bracket is
bracket, the engineer must use 4 x M6x16 St
suitable for mounting the Vx at both 0
St socket head cap screws as the existing
degree and 90 degree orientations.
carrier screws are too long.
Image/ Diagram

BOM Notes
0.9m Bracket Module (5-0460259): See also CB41 for bracket
1x Window End Plate Kit-LH (5-0460253) construction configuration
1x Window End Plate Kit-RH (5-0460252) details and part numbers.
2 x 0.9m Stainless Steel Tube Assemblies (5-0460003)
3 x 0.9m Aluminium Guide Roller Assemblies (5-0460004)
1 x Printer Carrier Assembly (5-0460258)
1x Mounting Block Kit – Pack of 2 (5-0460019)
Incl. fasteners

IM Platen Module (5-0460007):

1 x IM Platen Assembly (5-0460008)
2 x 0.9m Stainless Steel Tube Assemblies (5-0460003)

EPT071549 Issue 3, March 2024 55

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and assembled
0.9m V3 CM Bracket Assembly - on site.
Order 5-0460259 (Basic 0.9m • Stainless steel support tubes and
Bracket Module) and all CM aluminium guide rollers can be cut
components as per BOM down to any width as required.
• Additional printer carrier, rubber
print-roller kit, axle kit, encoder
Description: This continuous window
assembly and guide rollers are available
bracket assembly can be used for mounting
separately.
Vx printers with adaptor EAS002346 onto
• Correct rubber print roller length to
customer packaging machines.
be selected as required by application.
Note: when ordering the separate
encoder, select the Vx encoder assembly
Note: To mount the Vx printers to this
(EPT069181) in the configurator.
bracket, the engineer must use 4 x M6x16 St
St socket head cap screws as the existing
carrier screws are too long.
Image/ Diagram

BOM Notes
0.9m Bracket Module (5-0460259): See also CB41 for bracket
1x Window End Plate Kit-LH (5-0460253) construction configuration
1x Window End Plate Kit-RH (5-0460252) details and part numbers.
2 x 0.9m Stainless Steel Tube Assemblies (5-0460003)
3 x 0.9m Aluminium Guide Roller Assemblies (5-0460004)
1 x Printer Carrier Assembly (5-0460258)
1x Mounting Block Kit – Pack of 2 (5-0460019)
Incl. fasteners

CM Components:
1 x 0.9m CM Axle Kit (5-0460277)
1 x Encoder Assembly (5-0460011) - Note: existing encoder
to be replaced with Vx encoder EPT069181.
1x Rubber Print Roller (See Print Roller Selection Table)

56 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and
1.4m V3 IM Bracket Assembly - assembled on site.
Order 5-0460262 (Basic 1.4m • Stainless steel support tubes
Bracket Module) and 5-0460276 and aluminium guide rollers
(1.4m Platen Module) can be cut down to any
width as required.
• Additional printer carrier, IM
Description: This intermittent window
platen, rubber kit and guide
bracket assembly can be used for mounting Vx
rollers are available
printers with adaptor EAS002346 onto
separately.
customer packaging machines.
This bracket is suitable for mounting the Vx at
Note: To mount the Vx printers to
both 0 degree and 90 degree orientations.
this bracket, the engineer must use 4 x
M6x16 St St socket head cap screws as
the existing carrier screws are too long.
Image/ Diagram

BOM Notes
1.4m Bracket Module (5-0460262): See also CB41 for bracket
1x Window End Plate Kit-LH (5-0460253) construction configuration
1x Window End Plate Kit-RH (5-0460252) details and part numbers.
2 x 1.4m Stainless Steel Tube Assemblies (5-0460256)
3 x 1.4m Aluminium Guide Roller Assemblies (5-0460263)
1 x Printer Carrier Assembly (5-0460258)
1x Mounting Block Kit – Pack of 2 (5-0460019)

IM Platen Module (5-0460276):

1 x IM Platen Assembly (5-0460008)
2 x 1.4m Stainless Steel Tube Assemblies (5-0460256)

EPT071549 Issue 3, March 2024 57

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and assembled
1.4m V3 CM Bracket Assembly - on site.
Order 5-0460262 (Basic 1.4m • Stainless steel support tubes and
Bracket Module) and all CM aluminium guide rollers can be cut
components as per BOM down to any width as required.
• Additional printer carrier, rubber
print-roller kit, axle kit, encoder
Description: This continuous window
assembly and guide rollers are available
bracket assembly can be used for mounting
separately.
Vx printers with adaptor EAS002346 onto
• Correct rubber print roller length to
customer packaging machines.
be selected as required by application.
Note: when ordering the separate
encoder, select the Vx encoder assembly
Note: To mount the Vx printers to this
(EPT069181) in the configurator.
bracket, the engineer must use 4 x M6x16 St
St socket head cap screws as the existing
carrier screws are too long.
Image/ Diagram

BOM Notes
1.4m Bracket Module (5-0460262): See also CB41 for bracket
1x Window End Plate Kit-LH (5-0460253) construction configuration
1x Window End Plate Kit-RH (50460252) details and part numbers.
2 x 1.4m Stainless Steel Tube Assemblies (5-0460256)
3 x 1.4m Aluminium Guide Roller Assemblies (5-0460263)
1 x Printer Carrier Assembly (5-0460258)
1x Mounting Block Kit – Pack of 2 (5-0460019)
Incl. fasteners

CM Components:
1 x 1.4m CM Axle Kit (5-0460278)
1 x Encoder Assembly (5-0460011) - Note: existing encoder
to be replaced with Vx encoder EPT069181.
1x Rubber Print Roller (See Print Roller Selection Table)

58 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Labeller Bracket Web Positioning Roller Assemblies

Product Technical Data
• The web positioning rollers are assembled
V1, V2 & V3 Labeller Bracket directly to the underside of the labeller
Web Positioning Roller bracket platens by means of M6 screws
Assemblies (supplied with roller assemblies).
• 160mm long rollers as well as 210mm long
Description: These optional web rollers are available and should be selected
positioning roller assemblies are used to to suit the application.
enable manual adjustment of the label • Three types of roller assemblies are
ribbon‘s linear position when using the available and can be selected individually to
V1/V2 and V3 labeller brackets. suit the application: Fixed, Adjustable and
extension-Adjustable.
• Rollers can be assembled on either side of the platen to suit the labeller bracket handing.
• The standard labeller brackets are supplied with web guide-strips on either edge of the
platen. These need to be removed before fitting the web positioning rollers.

Image/ Diagram

BOM
EAS001597: Roller Mount Assembly, V3 (A) EAS002411: Roller Mount Assembly, V1/V2
EAS001601: Roller Mount Assembly, V3 (B) (A)
EAS001604: Roller Extension Plate, EAS002412: Roller Mount Assembly, V1,V2
V1/V2/V3 (C) (B)
EAS002091: Roller Mount Assembly, V3 (A) EAS001927: Roller Assembly, 160mm, Spare
EAS002092: Roller Mount Assembly ,V3 (B) EAS001928: Roller Assembly, 210mm, Spare
EAS002093: Roller Extension Plate
Assembly, V1/V2/V3 (C) Notes
EAS002409: Roller Mount Assembly, V1/V2
(A) All types supplied with 1 roller.
EAS002410: Roller Mount Assembly, V1/V2 See CB28 for further details and part
(B) numbers.

EPT071549 Issue 3, March 2024 59

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Type A - Labeller Bracket Web Positioning Roller

Assemblies
Product Technical Data
• The web positioning rollers are
V3 Roller Mount Assembly, assembled directly to the underside
Adjustable, 160mm, Type A - of the labeller bracket platens by
EAS001597 means of M6 screws (supplied with
roller assemblies).
• 160mm long roller
Description: This web positioning roller
mount assembly is used to enable manual
adjustment of the label ribbon’s linear
position when using V3 labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

60 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V3 Roller Mount Assembly, assembled directly to the underside
Adjustable, 210mm, Type A - of the labeller bracket platens by
EAS002091 means of M6 screws (supplied with
roller assemblies).
• 210mm long roller
Description: This web positioning roller
mount assembly is used to enable manual
adjustment of the label ribbon’s linear
position when using V3 labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

EPT071549 Issue 3, March 2024 61

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V1/V2 Roller Mount Assembly, assembled directly to the underside
Adjustable, 160mm, Type A - of the labeller bracket platens by
EAS002409 means of M6 screws (supplied with
roller assemblies).
• 160mm long roller
Description: This web positioning roller
mount assembly is used to enable manual
adjustment of the label ribbon’s linear
position when using V1/V2 labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

62 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V1/V2 Roller Mount Assembly, assembled directly to the underside
Adjustable, 210mm, Type A - of the labeller bracket platens by
EAS002411 means of M6 screws (supplied with
roller assemblies).
• 210mm long roller
Description: This web positioning roller
mount assembly is used to enable manual
adjustment of the label ribbon’s linear
position when using V1/V2 labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

EPT071549 Issue 3, March 2024 63

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Type B - Labeller Bracket Web Positioning Roller

Assemblies
Product Technical Data
• The web positioning rollers are
V3 Roller Mount Assembly, assembled directly to the underside
Fixed, 160mm, Type B - of the labeller bracket platens by
EAS001601 means of M6 screws (supplied with
roller assemblies).
• 160mm long roller
Description: This roller mount assembly is
used to guide the label ribbon when using V3
labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

64 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V3 Roller Mount Assembly, assembled directly to the underside
Fixed, 210mm, Type B - of the labeller bracket platens by
EAS002092 means of M6 screws (supplied with
roller assemblies).
• 210mm long roller
Description: This roller mount assembly is
used to guide the label ribbon when using V3
labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

EPT071549 Issue 3, March 2024 65

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V1/V2 Roller Mount Assembly, assembled directly to the underside
Fixed, 160mm, Type B - of the labeller bracket platens by
EAS002410 means of M6 screws (supplied with
roller assemblies).
• 160mm long roller
Description: This roller mount assembly is
used to guide the label ribbon when using
V1/V2 labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

66 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V1/V2 Roller Mount Assembly, assembled directly to the underside
Fixed, 210mm, Type B - of the labeller bracket platens by
EAS002412 means of M6 screws (supplied with
roller assemblies).
• 210mm long roller
Description: This roller mount assembly is
used to guide the label ribbon when using
V1/V2 labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

EPT071549 Issue 3, March 2024 67

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Type C - Labeller Bracket Web Positioning Roller

Assemblies
Product Technical Data
• The web positioning rollers are
V1/V2/V3 Roller Extension Plate assembled directly to the underside
Assembly, Adjustable, 160mm, of the labeller bracket platens by
Type C - EAS001604 means of M6 screws (supplied with
roller assemblies).
• 160mm long roller
Description: This web positioning roller
extension plate assembly is used to enable
manual adjustment of the label ribbon’s linear
position when using the V1/V2 and V3
labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

68 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The web positioning rollers are
V1/V2/V3 Roller Extension Plate assembled directly to the underside
Assembly, Adjustable, 210mm, of the labeller bracket platens by
Type C - EAS002093 means of M6 screws (supplied with
roller assemblies).
• 210mm long roller
Description: This web positioning roller
extension plate assembly is used to enable
manual adjustment of the label ribbon‘s linear
position when using the V1/V2 and V3
labeller brackets.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

EPT071549 Issue 3, March 2024 69

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Roller Assemblies
Product Technical Data
• 160mm long roller
Roller Assembly, 160mm, Spare - • The roller kits are assembled directly
EAS001927 into the slots of the roller mount
assemblies.
Description: This is a spare/additional
roller kit for fitting to the various roller
mount assemblies on the labeller bracket
(V1/V2/V3) web positioner.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

70 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• 210mm long roller
Roller Assembly, 210mm, Spare - • The roller kits are assembled directly
EAS001928 into the slots of the roller mount
assemblies.
Description: This is a spare/additional
roller kit for fitting to the various roller
mount assemblies on the labeller bracket
(V1/V2/V3) web positioner.
Image/ Diagram

Connection/ Fitting Notes

See CB28 for further details
and part numbers

EPT071549 Issue 3, March 2024 71

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

V-Series L-Bracket Assembly

Product Technical Data
• Supplied in a flat-pack and
0.9m V-Series CM L-Bracket
assembled on site.
Assembly - Order of 5-0460012 • Stainless steel support tubes and
(Basic 0.9m Bracket Module) and aluminium guide rollers can be cut
all additional CM components as down to any width as required.
per BOM • Additional printer carrier, rubber
print-roller kit, axle kit, encoder
Description: This continuous L-bracket assembly and guide rollers are
assembly can be used for mounting Vx printers available separately.
with adaptor EAS002346 onto customer • Correct rubber print roller length
packaging machines. to be selected as required by
application.
Note: When ordering the separate encoder,
select the Vx encoder assembly (EPT069181) Note: To mount the Vx printers to this
in the configurator. This L-Bracket is not bracket, the engineer must use 4 x M6x16
available in an IM version and also not in 1.4m St St socket head cap screws as the
lengths . See also CB41 for configuration existing carrier screws are too long.
details and part numbers.
Image/ Diagram

Connection/ Fitting BOM

0.9m CM L-Bracket Module (5-0460012):
1x End Plate Kit-L LH (5-0460254)
1x End Plate Kit-L RH (5-0460255)
2 x 0.9m Stainless Steel Tube Assemblies
(5-0460003)
2 x 0.9m Aluminium Guide Roller Assemblies
(5-0460004)
1 x Printer Carrier Assembly-L (5-0460013)
1x Mounting Block Kit – Pack of 2 (5-0460019)
Incl. fasteners

CM Components:
1 x 0.9m CM Axle Kit (5-0460277)
1 x Encoder Assembly (5-0460011) - Note: existing
encoder to be replaced with Vx encoder EPT069181
1x Rubber Print Roller
(See Print Roller Selection Table)

72 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Labeller Bracket Assemblies

Product Technical Data
• Supplied in a flat-pack and can be
V1/V2 Labeller Bracket assembled on site as a right-hand or left-
Assembly - EAS001626 hand version.
• Aluminium frame with adjustable printer
Description: This bracket assembly could carrier.
be used for mounting Vx printers onto • Printer carrier can operate at 0 degree or
customer labelling machines, however the 90 degree positions.
base plate would need to be modified to • Various M6 mount holes available on
suit 0 degree and 90 degree Vx printer underside of the print platen for mounting
orientations – see drawing EPT070447 for to customer labelling machines.
local manufacturing of new base plate to • Optional web-positioning roller units are
suit the Vx print area. available and can be mounted directly to
The existing V3 elastomer pad the underside of the print platen.
(EAS002089) should be used for fitting to
the modified Vx base plate. Note: This Labeller Bracket Assembly is only
listed in the V-Series Configurator. To mount
the Vx printers to this bracket, the engineer
must use 4 x M6x16 St St socket head cap
screws as the existing carrier screws are too
long.
Image/ Diagram

BOM
1x Top Plate 1x Printer Mount Plate
9x M6 Flat Washers 1x Orange Elastomer Base (EAS002417) – Use
1x Lead Screw EAS002089 for modified Vx base plate.
1x Bush 4x M6x12 Cap Screws
1x Front plate 2x Guide Strips
1x Locking Plate 6x M3 Flat Washers
1x M10 Flat Washer 6x M3x10 Pan Head Screws
1x Clamp Handle 1x M6 Lock Washer
1x M5 Flat Washer
1x Crank Handle Notes
8x M6x30 Button Head Screws
1x Rear Plate See CB28 for further details and part numbers
1x Base Plate (To be modified for Vx) of BOM.

EPT071549 Issue 3, March 2024 73

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and can be
V3 Labeller Bracket Assembly - assembled on site as a right-hand or left-
EAS001568 hand version.
• Aluminium frame with adjustable printer
Description: This bracket assembly can be carrier.
used for mounting Vx printers onto • Printer carrier can operate at 0 degree or
customer labelling machines, however only 90 degree positions.
when the standard adaptor kit EAS002346 • Various M6 mount holes available on
is used and also when the 128mm printer underside of print platen for mounting to
carrier position is used (both 53mm and customer labelling machines.
128mm positions are marked on the • Optional web-positioning roller units are
labeller bracket printer carrier). available and can be mounted directly to
underside of print platen.

Note: To mount the Vx printers to this

bracket, the engineer must use 4 x M6x16 St
St socket head cap screws as the existing
carrier screws are too long.
Image/ Diagram

BOM
1x Top Plate 1x Clamp Handle
1x Lead Screw 1x Printer Mount Plate
1x Rear Plate 1x M5 Flat Washer
1x Base Plate 1x Crank Handle
1x Orange Elastomer Base (EAS002089) 4x M6x12 Cap Screws
1x Bush 1x M6 Lock Washer
11x M6 Flat Washers
2x Guide Strips Notes
6x M3 Flat Washers
6x M3x10 Pan Head Screws See also CB28 for further details and part
1x Front plate numbers of BOM.
10x M6x30 Button Head Screws
1x Locking Plate The standard adaptor kit EAS002346
1x M10 Flat Washer would need to be used when mounting Vx
printers.

74 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Web Positioning Module Assemblies

Product Technical Data
• Supplied in a flat-pack and assembled
0.9m Web Positioning Module on site.
Assembly - 5-0460281 • Aluminium end plates with laser
etched graduated scale for repeatable
Description: The 0.9m Web Positioning positioning.
Module is used in conjunction with window • Aluminium guide rollers which can be
and L-brackets to enable manual adjustment cut down to any width as required.
of the web’s linear position. • Spare rack & pinion kit is available
separately.
Image/ Diagram

BOM Notes
2x Web Positioning Plate Assembly See CB41 for further details
2x Guide Roller Assembly-0.9m (5-0460004) and part numbers
1x Mounting Block Kit – Pack of 2 (5-0460019)
8x M6x16 Cap Screws
1x Web Positioning Roller Assembly-0.9m

Spare Rack and Pinion kit (2x sets): 5-0460280

EPT071549 Issue 3, March 2024 75

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• Supplied in a flat-pack and assembled
1.4m Web Positioning Module on site.
Assembly - 5-0460275 • Aluminium end plates with laser
etched graduated scale for repeatable
Description: The 1.4m Web Positioning positioning.
Module is used in conjunction with window • Aluminium guide rollers which can be
and L-brackets to enable manual adjustment cut down to any width as required.
of the web’s linear position. • Spare rack & pinion kit is available
separately.
Image/ Diagram

BOM Notes
2x Web Positioning Plate Assembly See CB41 for further details
2x Guide Roller Assembly-1.4m (5-0460263) and part numbers
1x Mounting Block Kit – Pack of 2 (5-0460019)
8x M6x16 Cap Screws
1x Web Positioning Roller Assembly-1.4m

Spare Rack and Pinion kit (2x sets): 5-0460280

76 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Printer & Print Roller Mount Adaptor Kits - Domino

Bracket Kits
Product Technical Data
• Kit is assembled directly onto
Printer Carrier Assembly, Quick flatpack bracket support bars.
Release, V1/V2 - EPT006141 • Allows quick-release of printers in
washdown environments or where
Description: This quick-release printer regular printer removal is required.
carrier kit can be used for mounting the Vx • Release & clamping is carried out by
printers onto V1/V2 flatpack IM & CM thumb-screws and no tools required.
window brackets. In IM applications, the Vx • Printer can be inserted at 0º or 90º
can be mounted in the 0 degree orientation positions.
position, however it would not be suitable
for the 90 degree position as there would
not be full print area coverage on the IM
platen.
Image/ Diagram

Connection/ Fitting BOM

1x Printer Carrier Base
1x Clamp Bar
2x Shoulder Screw M8 x Dia10
x 25
1x T-Bar Assembly (5-0460018)
2x Clamp Plate
1x Quick Release Adaptor
2x Thumb Screws M6x16
4x M4x8 Countersunk Screws
4x M6x16 Countersunk Screws

EPT071549 Issue 3, March 2024 77

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The kit is fitted directly onto the Vx
Adaptor Plate Kit, V-Series printer mount pad with M6 screws
Window & L-Brackets - and then assembled to the V3
EAS002346 flatpack Window, Labeller or L-
Bracket printer carriers.
• This kit is also used for mounting the
Description: This adaptor kit can be used
Vx printers to the previous style
for mounting Vx printers onto all V3
(non-flatpack) Window and L-
Window, Labeller and L-Brackets.
Brackets as well as the older 217mm
On IM brackets, this adaptor can be used for
pillar-style brackets and the V3
both 0 degrees and 90 degrees Vx printer
flatpack labeller brackets.
orientations.
• Various mount holes are provided on
Note: See CB41 for further details the adaptor to allow for lateral
printer adjustment.
Image/ Diagram

Connection/ Fitting BOM

1x Adaptor Plate
8x M6x30 Cap Screws
4x M6x50 Cap Screws
4x M6 Flat Washers

78 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Printer & Print Roller Mount Adaptor Kits - Competitor

Bracket Kits
Product Technical Data
• The kit is fitted directly onto the Vx
Adaptor Plate Kit - Markem SD - printer mount pad with M6 screws
EAS002226 and then assembled to the Markem
window or L-brackets.
Description: This adaptor kit can be used • Various mount holes are provided on
for mounting Vx printers directly onto the adaptor to allow for lateral
Markem SD/X40/X60 standard window or L- printer adjustment.
brackets.
This adaptor will work with CM applications
as well as IM applications at 0 degree printer
orientation and 90 degree printer
orientation.
Image/ Diagram

Connection/ Fitting BOM

1x Adaptor Plate
8x M6x25 Cap Screws

EPT071549 Issue 3, March 2024 79

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The kit consists of 2 aluminium split-
Adaptor Bush Kit, Print Roller bushes. One bush is fitted onto each
Shaft, 16mm DIA, end of the Domino print roller shaft
Markem/VideoJet - EPT005445 before fitting and clamping into the
competitor bracket shaft bores.
Description: This adaptor kit is used for
mounting Domino CM print roller shafts
(12mm diameter) directly onto Markem or
VideoJet Window/L-Brackets brackets,
having standard shaft bores of 16mm
diameter.
Image/ Diagram

Connection/ Fitting BOM

2x Shaft Bushes

80 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The carrier kit is fitted directly onto
Adaptor Plate Kit, Markem S18-L the Vx mount pad with M6 screws
- EAS002586 and then assembled to the support
tubes of the Markem S18 L-brackets.
Description: This adaptor kit can be used • No additional mount holes are
for fitting Vx printers onto standard CM & provided on the adaptor to allow for
IM Markem S18 L-Brackets. The Vx printer lateral printer adjustment.
will fit directly onto this adaptor when using
the CM L-Bracket. When fitting the Vx
printer to this adaptor on IM L-Brackets, a
direct fit will be suitable for 0 degree printer
orientation. However for 90 degree
orientation, four additional offset 6.5mm
diameter holes can easily be drilled on site in
order for the Vx print heads to be correctly
positioned on the Markem IM platen.
Image/ Diagram

Connection/ Fitting BOM

1x Printer Mount Plate
1x Clamp Mount Plate
1x Clamp
6x M6x20 Cap Screws
1x M10 Flat Washer
1x M10 Wing Knob
2x Shoulder Screws M5 x 6
dia x 20

EPT071549 Issue 3, March 2024 81

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The kit is fitted directly onto the Vx
Adaptor Plate Kit, VideoJet DF - printer mount pad with M6 screws
EAS002559 and then assembled to the VideoJet
window or L-brackets.
Description: This adaptor kit is used for
mounting Vx printers directly onto VideoJet
Dataflex standard window or L-brackets
brackets (Note: relevant only to Dataflex
printers which are 178mm high). This
adaptor will work with all CM brackets. This
adaptor will also work with all IM brackets at
0 degree printer orientation, however at 90
degree printer orientation the adaptor
mount-hole positioning would need to be
modified on site.
Image/ Diagram

Connection/ Fitting BOM

1x Adaptor Plate
8x M6x25 Cap Screws

82 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Product Technical Data

• The carrier kit is fitted directly onto
Adaptor Plate Kit, VideoJet the Vx printer mount pad with M6
6210-W - EAS002634 screws and then assembled to the
support tubes of the VideoJet 6210
Description: This adaptor kit is used for window brackets.
mounting Vx printers directly onto VideoJet • Additional mount holes are provided
6210 standard window brackets. (Note: on the adaptor to allow for lateral
relevant only to Dataflex printers which are printer adjustment.
158mm high). This adaptor will work with
CM applications as well as IM applications at
both 0 degree printer orientation and 90
degree printer orientation.
Image/ Diagram

Connection/ Fitting BOM

1x Printer Mount Plate
1x Clamp
4x M6x16 Cap Screws
1x M10 Flat Washer
1x M10 Wing Knob
2x Shoulder Screws M5 x 6 dia x 20

EPT071549 Issue 3, March 2024 83

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

OEM Brackets & Accessories

Product Technical Data
• The Adaptor Plate assemblies fit directly
Ishida Atlas Adaptor Plate Kit - to existing holes on the base of the Ishida
EPT045886 Atlas machine and are configurable for LH
or RH.
Description: This kit is used for fitting the • The user interface adaptor fits directly to
standard Domino V1/V2 CM flat-pack existing holes on the flat-pack bracket
window bracket (which would need to be end-plates.
cut to the required width) onto Ishida Atlas
bagging machines, models 201, 202, 203 & Note: Refer to Ishida Atlas Integration
204. This kit also contains an adaptor for Guide on MyDomino for full installation
fitting the user interface mount arm onto the details.
Domino CM flat-pack bracket. The Vx
printer will fit directly onto the above
bracket.
Image/ Diagram

Connection/ Fitting BOM

1 x Adaptor Plate - Side
1 x Adaptor Plate - Base
9 x Screw M6 x 20
6 x M6 Flat Washer
2 x M6 x 30 Skt Cap St St
1 x UI Mount Plate

Kit EPT045886 consists of:

(2 x Adaptor Plate
Assemblies – EPT023289 and
1x UI Mount Plate Assembly
– EPT043396)

84 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

Food Quality Rubber Print Roller Selection Table

Food Quality 305mm Rubber Roller /
EPT018342
Bearing Kit
Food Quality 405mm Rubber Roller /
EPT018343
Bearing Kit
Food Quality 505mm Rubber Roller /
EPT018344
Bearing Kit
Food Quality 605mm Rubber Roller /
EPT018345
Bearing Kit
Food Quality 705mm Rubber Roller /
EPT018346
Bearing Kit
Food Quality 805mm Rubber Roller /
EPT018347
Bearing Kit
Food Quality 905mm Rubber Roller /
EPT018348
Bearing Kit
Food Quality 1005mm Rubber Roller /
EPT018349
Bearing Kit
Food Quality 1105mm Rubber Roller /
EPT018350
Bearing Kit
Food Quality 1205mm Rubber Roller /
EPT018351
Bearing Kit
Food Quality 1305mm Rubber Roller /
EPT018352
Bearing Kit

Food Quality Rubber Roller with Bearing Kit Fitted (1 Bearing Fitted to Each Side).

EPT071549 Issue 3, March 2024 85

Vx-Series Spares & Accessories Catalogue - Bracket Assemblies

86 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue – Bespoke Solutions

Bespoke Solutions
Specialised Solutions .................................................................................................. 88

EPT071549 Issue 3, March 2024 87

 Vx-Series Spares & Accessories Catalogue - Bespoke Solutions

Specialised Solutions
Many special brackets and accessories have previously been designed for specific installations
and can be re-used or adapted for other applications. These are not sales-enabled parts but
they are listed for general reference in the non-sales enabled catalogue EPT019442 in the
MyDomino portal.

Drawings and details for these parts are also available for local manufacture by channels.

Contact mailto:[email protected] for further details.

Some Typical Examples:

High strength bracket to resist deformation from high substrate Extension of special (Markem) L Bracket allowing Domino V2 &
tensions and for spans up to 2.11 metres Vx to be fitted with minimum disruption

Special dapter developed allowing V-Series to be installed in Adapter allowing V-Series & Vx to be retrofitted to standard
existing (Allen) labeller bracket Markem window bracket

Herma labeller bracket to fit onto standard Herma 400 labelling Bespoke bracket for Ishida Atlas bagging machine
machine

88 EPT071549 Issue 3, March 2024

 Vx-Series Spares & Accessories Catalogue - Notes

Notes

EPT071549 Issue 3, March 2024 89

j>ooMINO

Domino Vx-Series Spares, Accessories & Brackets Catalogue

Domino Printing Sciences pie has a policy of continuous product improvement, the Company
therefore reserves the right to modify the specification contained within this document without
notice.
© Domino Printing Sciences pie 2024. All rights reserved.