HydProve Brushflex Builder’s Solutions

Two component, elastomeric, crack-bridging cementitious

waterproofing membrane

Advantages
▪ Elastomeric – able to bridge cracks
Product Data Sheet

▪ Non-toxic according to BS 6920 Part 1

▪ Can be applied to damp substrates
▪ No primer required
▪ Suitable for horizontal and vertical application
▪ Excellent adhesion to practically all surfaces
▪ Factory pre-blended two component system ensures
quality control at site

Uses
▪ Waterproof lining for water retaining structures such
as swimming pool, water tanks
▪ Toilets and bathroom waterproofing
▪ Planter boxes and gutters lining
▪ Wet areas waterproofing such as kitchens and
pantries
▪ Protect concrete and masonry against ingress of
chloride ions and carbonation process
▪ Retaining wall, basement and lift pit

Description
HydProve Brushflex is a two component acrylic polymer modified cementitious waterproofing membrane
supplied as ready to use kits. When mixed, an easily brushable slurries produced which can simply be applied
using a stiff brush.

Standards compliance Technical Properties

HydProve Brushflex is deemed to be suitable for use Properties Value
in contact with potable water sources for human Pot life at 35ºC Approx. 1 to 1.5 hrs
consumption as tested against BS6920 Part 1. Mixed density 1.45
Adhesion to substrate 1.0 N/mm2
Technical Support ASTM D4541
Shore A hardness >70
Hydresist Global offers a comprehensive range of
ASTM D2240
construction products. In complement to a wide Tensile strength 2.0 N/mm2
range of quality products, Hydresist Global offers ASTM D412
technical assistance to specifiers and contractors Elongation at break >150%
which include product selection and technical advice. ASTM D412
Water permeability nil
Supply DIN 1048 Pt5
Water vapor transmission 6.0 g/m2/day
HydProve Brushflex Comp A (powder) 20 kg bag ASTM E96
Crack bridging 2.0 mm
Comp B (liquid) 10 kg pail
ASTM C836
TOTAL 30 kg set Water absorption <1%
BS1881 Pt 122

Page 1 of 2
 Builder’s Solutions

Storage Apply a layer of HydProve Brushflex at a rate of 1.0

HydProve Brushflex has a shelf life of 12 months in – 1.5 kg/m2. Leave the material to dry for 24 hours.
unopened packs and stored in cool, dry and shaded Apply the second layer of HydProve Brushflex at a
environment. In high humidity locations, the shelf life rate of 1.0 - 1.5 kg/m2 at the direction perpendicular
may be reduced to 10 months. to the first coat. Leave the material to dry for 24
hours.
Instruction for Use If necessary apply a third layer at 1.0 – 1.5 kg/m2.
Substrate Preparations
All surfaces to be waterproofed should be sound, Cleaning
clean, dry and free from loose particles or other Uncured HydProve Brushflex should be cleaned
contaminants that prevent good membrane using water. Cured material can only be removed
bonding to substrate. mechanically.

Priming Consumption and Coverage

The use of a primer is generally not required when The consumption rate is approximately 1.0 - 1.5
using HydProve Brushflex. kg/m2.

Mixing Health and Safety

Pour Component B liquid into a mixing container.
HydProve Brushflex is non-toxic. Due to
Mix mechanically using slow speed electric mixer
cementitious based material, HydProve Brushflex is
fitted with spiral paddle. Add gradually Component
alkaline in nature. The use of protective gloves and
A powder whilst stirring. Mix for 4-5 minutes until a
goggles is recommended. In the event of accidental
smooth homogenous slurry is produced.
splashes to skin and eye, wash off thoroughly with
plenty of clean water. In irritation persists, seek
Tools
medical advice. Powder products should be handled
HydProve Brushflex should be applied by stiff brush.
to minimise dust formation. Maintain good
ventilation. The use of mask is recommended.
Application
For detail information and advice on safe handling,
Pre-damp the prepared substrate with clean water. storage and disposal, please refer to recent Safety
For best result, It is recommended to pre-damp the Data Sheet (SDS).
surface 1-2 hours prior to application of HydProve
Brushflex.

Legal Disclaimer
Hydresist Global endeavors to ensure that any advice, recommendation or information it may give is accurate and correct. It cannot accept any liability either
directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether
or not in accordance with any advice, specification, recommendation or information given by it. Hydresist Global has the right to change any of the
specifications mentioned in the Technical Data Sheets upon its discretion.

Hydresist Global Sdn Bhd (1214055-D)

No. 36 Jalan Bulan U5/168,
Bandar Pinggiran Subang, 40150 Shah Alam
Selangor Darul Ehsan, Malaysia Tel 03 7842 6600 / 7842 6688 Fax 03 7859 9186

Revision 2 (A’2020)
Page 2 of 2