Scribd
Upload
20 views

TDS HydPatch GP

adfadf

Uploaded by

Doughnut Chilli Pi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
20 views

TDS HydPatch GP

adfadf

Uploaded by

Doughnut Chilli Pi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HydPatch GP Builder’s Solutions

General purpose patch repair mortar

Advantages
Product Data Sheet

▪ Structural grade patch material


▪ Polymer modified - high strength, good workability
▪ Dense, low water permeability
▪ High bond strength
▪ Ease of use requiring only addition of water

Uses
▪ Vertical and overhead repairs
▪ Patch repairs to steps, stairs or other areas subject to
heavy traffic
▪ General structural repairs where formwork cannot
easily be erected
▪ Parking lots
▪ Ports
▪ Engineering workshops

Description
HydPatch GP is a ready to use structural patch repair material where significant load bearing is required. It is
suitable for hand application especially for heavily congested rebar area. The low permeability properties provide
optimum protection to steel reinforcement from chloride attack. HydPatch GP is shrinkage compensated thus
suitable for both small and large area applications.

Technical Support Technical Properties


Hydresist Global offers a comprehensive range of Properties Value
construction products. In complement to a wide Compressive Strength 50 N/mm² at 28 days
range of quality products, Hydresist Global offers (BS 4552)
technical assistance to specifiers and contractors Flexural Strength 5.5 M/mm² at 28 days
which include product selection and technical (BS 4551)
Tensile Strength 1.7 N/mm² at 28 days
advice.
(BS6319 Part 7 1985)
Water Absorption ISAT 10 min : 0.225 ml/m2/sec
Supply (BS 1881 Pt 5 1970)
Setting Time Dependent on
HydPatch GP 25 kg bag temperature and water
content typically 2-4 hours
Chemical resistance Substantially reduced
Storage resistance absorption;
slows-down chemical
HydPatch GP has a shelf life of 12 months if stored
attack in aggressive
in cool, dry and shaded environment environments

Page 1 / 2
Builder’s Solutions

Instruction for Use with the primed substrate. Start application with
Substrate Preparations tamping or compacting action. Wood or steel float
All surfaces to be repaired should be sound, clean, can be used for finishing depending to type of finish
dry and free from loose particles or other required. Apply HydPatch GP at minimum 5mm
contaminants that prevent good bonding to thick. For vertical application 20 – 25mm thickness
substrate. Any laitance should be mechanically can be achieved.
removed. Oil and grease deposits should be Curing
removed by steam cleaning, detergent scrubbing
Installed HydPatch GP should be cured immediately
or use of any proprietary degreaser. Smooth
after finishing in accordance with good concrete
surface should be mechanically roughened to form
practice. The use of HydBond SBR curing agent is
good mechanical key. All reinforcing steel should
recommended.
be grit blasted to SA 21/2 profile prior to application
Cleaning
of recommended primer. Edges of areas to be
repaired should be saw cut to 5mm depth. Uncured HydPatch GP should be cleaned using
Surface area should be pre-wetted to damp water. Cured material can only be removed
condition before application of repair mortar. mechanically.

Steel Reinforcement Primer Consumption and Coverage


All reinforcing steel must be primed with HydPrime The yield is approximately 12-16 litres/25kg bag
Zincpruf active zinc epoxy system.
Concrete must be primed with HydBond SBR Health and Safety
bonding agent scrubbed onto the surface. Wait
HydPatch GP contains Portland cement which is
until applied HydBond SBR become tacky before
alkaline when in contact with water. Avoid
commencing application of repair mortar.
prolonged contact with the skin. Avoid contact to
Mixing eyes. In the event of accidental eye contact, rinse
Ensure that HydPatch GP is thoroughly mixed prior thoroughly with plenty of running water and seek
to use. For large application, the use of force action medical treatment immediately.
pan mixer is highly recommended. For small After full curing, HydPatch GP is physiologically
application which requires 1 bag mixing, the use of harmless.
high capacity electrical hand drill fitted with spiral For detail information and advice on safe handling,
mixing paddle is allowable. storage and disposal, please refer to recent Safety
Data Sheet (SDS).
Application
It is recommended that HydPatch GP be applied
with a wood float to ensure positive contact

Legal Disclaimer
Hydresist Global endeavors to ensure that any advice, recommendations or information it may give is accurate and correct. It cannot accept any liability
either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied,
whether or not in accordance with any advice, specification, recommendation or information given by it. Hydresist Global has the right to change any of the
specifications mentioned in the Technical Data Sheets upon its discretion.

Hydresist Global Sdn Bhd (1214055-D)


No. 36, Jalan Bulan U5/168
Bandar Pinggiran Subang, 40150 Shah Alam
Selangor Darul Ehsan, Malaysia Tel +603 7842 6600 / 7842 6688 Fax +603 7859 9186

Revision 2 (A’2020) Page 2 of 2

You might also like