International Journal of Scientific Engineering and Research (IJSER)

www.ijser.in
ISSN (Online): 2347-3878, Impact Factor (2015): 3.791

Implementation of PLC using FPGA

Dhruti Dave1, Punit Raninga2
1
Parul Institute of Engineering & Technology, Vaghodiya, Gujrat, India
2
Professor, Parul Institute of Engineering & Technology, Vaghodiya, Gujrat, India

Abstract: Programmable Logic Controller (PLC) is most important component in modern manufacturing automation systems.
Processor and software have been bottlenecks for improving operational efficiency of PLC. To enhance the PLC performance and
flexibility, a new design called “Design And Implementation Of FPGA Based PLC” has been proposed here. The design has been
simulated using knowledge of FPGA design tools (such as HDL), to translate, integrate and implement the logic circuit in FPGA. The
FPGA based Micro-PLC is based on parallel mechanism, so the proposed design works faster as compared to the conventional PLC.
Implementing control logic with FPGA to replace a PLC, response time can be improved while sustaining the flexibility of control. In
FPGA side Four- 32 bit 4 stage RISC pipeline Processors based on RUNG- Architecture are designed for dynamically forming and
controlling each rung. This design also provides increased flexibility because FPGA offers reconfigurable hardware, increased
reliability, better performance and faster scanning time.

Keywords: PLC, FPGA, HDL

1. Introduction FPGA is one of the prospective solutions for this requirement

[9]
. This further requires better designs and environments with
PLCs have established an important place as control elements built in reliable verification and validation methods. Once
for logic control of manufacturing systems.[1] Ladder this is achieved than an Integrated Development Environment
Diagram is widely used to program PLC, microprocessor of any of the FPGA manufacturer can provide a platform by
decodes and executes the LD program in a sequential and which developers can access all the necessary development
cyclic way, that’s why performance of PLC is limited and tools and components required for FPGA based PLC
depends on the length of program and speed of processor. In development[8][10]. The structure of FPGA is reconfigurable
order to overcome these drawback a new PLC design, a so the required circuit can be built as long as a LD program is
FPGA based PLC is proposed. It can achieve reconfigurable converted into RTL architecture and downloaded to the
hardware structure and parallel execution advantage. A FPGA chip. This implementation will perform the same
number of researchers have focused on this field. functions as the original PLC with LD, but not in traditional
Miyazawa[2] and Ikeshita et al.[3] developed a very rough manner. Below fig.1[5] shows the architecture of converter
manner in 1999 to convert the LD into a program description of LD to VHDL.
of a very high speed integrated circuit VHDL. Chen and
Patyra[4] designed a VHDL model of the whole system
directly from the original system requirements to build a
controller. The FPGA based Micro-PLC is based on parallel
mechanism, so the proposed design works faster as compared
to the conventional PLC. Implementing control logic with
FPGA to replace a PLC, response time can be improved
while sustaining the flexibility of control. In FPGA side
Four- 32 bit 4 stage RISC pipeline Processors based on
RUNG- Architecture are designed for dynamically forming
and controlling each rung. This design also provides
increased flexibility because FPGA offers reconfigurable
hardware, increased reliability, better performance and faster
scanning time.

2. FPGA Based PLC Design

The main Concept in the development of an integrated
environment for efficient conversion of IEC61131-3(ladder
diagram and functional block diagram) to IEEE1076.6
(VHSIC Hardware description language) is to develop the
software which can convert the conventional input of PLC
into the HDL[7][8]. Conventional PLCs are inherently
sequential due to implementation of ASIP or micro controller
at its core. By applying different range of the Frequencies to
Conventional PLCs, the output we get at the higher frequency Figure 1[5]: The architecture of converter of LD to VHDL
is null, it stops working. Thus implementation of PLC on

Volume 4 Issue 10, October 2016

Licensed Under Creative Commons Attribution CC BY
Paper ID: IJSER151015 72 of 73
 International Journal of Scientific Engineering and Research (IJSER)
www.ijser.in
ISSN (Online): 2347-3878, Impact Factor (2015): 3.791
3. Related Work Approach 5. Conclusion
One can convert ladder diagram in to c-code usin translation At higher complexity (higher clock rate) PLCs can’t able to
software and that c code is further converted into VHDL respond. That’s why by converting a Ladder Diagram into
code. Main tool is the catapult C high-level synthesis HDL and then this code can be implemented on FPGA board
software. As is well-known high-level synthesis is the process and further more FPGAs is still find to operate at higher
of transforming a system level behavioral specification of frequencies also. With the help of the HDL code : we have a
digital system into register-transfer level structural faster response than conventional PLCs and if we want to
description implementing that behavior. Catapult C takes as check it’s functionality with reference to different timings
input a functional description of an algorithm in C or System than we don’t have to make change in the full code by
C and produces a VHDL register-transfer level description of simply modifying and making proper constraints in the TEST
a logic circuit, which implements this algorithm. In BENCH we are able to check it all. We can’t able to do this
particular, Catapult C can be used for obtaining optimized all by using conventional PLCs.
designs, because it considers seversl alternative
implementations of the algorithm and selects one or more References
among them according to user-specified criteria.[6]
[1] Auslander DM, Pawlowski C, Ridgely J (1998)
Reconciling programmable logic controllers with
mechatronics control software. Proceedings of the 1998
IEEE international conference on control applications,
Trieste, Italy, pp 415–420
[2] Ikeshita M, Takeda Y, Murakoshi H, Funakubo N,
Miyazawa I (1999) Application of FPGA to high-speed
programmable controller—development of the
conversion program from SFC to Verilog. IEEE
symposium on emerging technologies and factory
Figure 2[6]: Design Methodology Overview automation, Piscataway, NJ, USA, vol 2, pp 1386–1390
[3] Miyazawa I, Nagao T, Fukagawa M, Itoh Y, Mizuya T,
4. Proposed Work Sekiguchi T (1999) Implementation of ladder diagram
for programmable controller using FPGA. IEEE
Here I am using NESYS 2 Spartan 3E family FPGA board symposium on emerging technologies and factory
and OMERON CP1E PLC for my design. The PLC can be automation, Piscataway, NJ, USA, vol 2, pp 1381–1385
configured by Ladder Diagram using CX programmer which [4] Chen J, Patyra MJ (1994) VHDL modeling of a
is provided by the manufacturer (OMERON). As per the multivariable fuzzy logic controller hardware system.
ladder diagram we have HDL code and FPGA can be IEEE international conference on fuzzy systems.
configured by that HDL code (bit file) using Xilinx. Now, Piscataway, NJ, USA, vol 1, pp 129–132
FPGA generates the different sequences as per the HDL [5] D. Du,Y. Liu:X. Guo:K. Yamazaki Department of
code. The generated output from FPGA is given to the PLC. Mechanical & Aeronautic Engineering, IMS-
As per the Ladder Diagram which PLC has it takes the output Mechatronics Laboratory, University of California,
of FPGA as an input and gave response accordingly. We can Davis, CA 95616, USA
check the response of the FPGA and PLC both using Logic [6] Christoforos Economakos*, George Economakos†
Analyzer. *Halkis Institute of Technology, Department Of
Automation, GR 34400, Psachna, Evia, Greece
†National. Tech. Univ. of Athens, School of ECE, uLab,
Iroon Polytexneiou 9, GR 15780, Athens, Greece,IEEE-
2008
[7] Adamski M, Monteiro JL (2000) From interpreted Petri
net specification to reprogrammable logic controller
design. IEEE international symposium on industrial
electronics, Puebla, Mexico, vol 1, pp 13–19
[8] Adamski M (1998) SFC, Petri nets and application
specific logic controllers, Proceedings of the IEEE
International Conference on Systems, Man and
Cybernetics. IEEE, Piscataway, NJ, USA 1:728–733
[9] Uzam M, Jones AH (1998) Discrete event control
system design using automation Petri nets and their
ladder diagram implementation. Int J Adv Manuf
Technol 14(10):716–728
[10] Lee JS, Hsu PL (2005) An improved evaluation of
ladder logic diagrams and Petri nets for the sequence
controller design in manufacturing systems. Int J Adv
Figure 3: Proposed Architecture
Manuf Technol 24(3–4):279– 287
Volume 4 Issue 10, October 2016
Licensed Under Creative Commons Attribution CC BY
Paper ID: IJSER151015 73 of 73