The most trusted, dependable name

in projector lamp sales.

http://www.myprojectorlamps.com

http://www.myprojectorlamps.ca

http://www.myprojectorlamps.eu

The following projector manual has not been modified or altered in any way.
 Before Using
OWNER'S MANUAL (Getting Started)
DATA PROJECTOR
TDP-S8

Preparations
Operations
Maintenance
Others
For more details , please refer to the owner's manual of the CD-ROM version
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is in-
tended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX-

POSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN
THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

WARNING: Handling the cord on this product or cords associated with accessories sold
USA only with this product, will expose you to lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. Wash hands af-
ter handling.

WARNING: This [product] contains mercury. Disposal of mercury may be regulated due
USA only to environmental considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries Alliance: www.eiae.
org.

MODEL NAME: TDP-S8 USA only

TRADE NAME: DATA PROJECTOR MODEL NAME: TDP-S8

Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE

FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. This
equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment gener-
ates, uses and can radiate radio frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

2
- Reorient or relocate the receiving antenna.

Before Using
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000

WARNING: Changes or modifications made to this equipment, not expressly approved by

USA only Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.

WARNING: This Class B digital apparatus complies with Canadian ICES-003. Cet appar-
CANADA only eil numérique de la classe B est conforme à la norme NMB-003 du Canada.

3
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUC-
TIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED
ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFER-
ENCE.
This set has been designed and manufactured to assure personal safety. Improper use
can result in electric shock or fire hazard. The safeguards incorporated in this unit will pro-
tect you if you observe the following procedures for installation, use and servicing. This unit
is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL ONLY.

1. Read Owner’s Manual 3. Source of Light

After unpacking this product, read Do not look into the lens while the
the owner’s manual carefully, and lamp is on. The strong light from
follow all the operating and other the lamp may cause damage to
instructions. your eyes or sight.

2. Power Sources 4. Ventilation

This product should be operated Openings in the cabinet are pro-
only from the type of power source vided for ventilation and to ensure
indicated on the marking label. reliable operation of the product
If you are not sure of the type of and to protect it from overheating,
power supply to your home, con- and these openings must not be
sult your product dealer or local blocked or covered. The openings
power company. should never be blocked by plac-
For products intended to oper- ing the product on a bed, sofa, rug
ate from battery power, or other or other similar surface. This prod-
sources, refer to the operating uct should not be placed in a built-
in installation such as a bookcase
instructions.
or rack unless proper ventilation
is provided or the manufacturer’s
instructions have been adhered to.

4
5. Heat 8. Power-Cord Protection

Before Using
The product should be situated Power-supply cords should be
away from heat sources such as routed so that they are not likely to
radiators, heat registers, stoves, be walked on or pinched by items
or other products (including ampli- placed upon or against them, pay-
fiers) that produce heat. ing particular attention to cords at
plugs, convenience receptacles,
and the point where they exit from
the product.

6. Water and Moisture

Do not use this product near wa-
ter. - for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a 9. Overloading
swimming pool and the like. Do not overload wall outlets;
extension cords, or integral con-
venience receptacles as this can
result in a risk of fire or electric
shock.

7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.

5
IMPORTANT SAFETY INSTRUCTIONS (Continued)
10. Lightning storms 12. Do not place the product
For added protection for this prod- vertically
uct during storm, or when it is left Do not use the product in the
unattended and unused for long upright position to project the pic-
periods of time, unplug it from the tures at the ceiling, or any other
wall outlet. This will prevent dam- vertical positions. It may fall down
age to the product due to lightning and dangerous.
and power-line surges. However,
while it is thundering or lightning,
do not touch the apparatus and
any connected cable and/or equip-
ment. This will prevent you from
receiving the electric shock by an
electric surge.

13. Stack Inhibited

Do not stack other equipment on
this product or do not place this
product on the other equipment.
11. Object and Liquid Entry Top and bottom plates of this
product develops heat and may
Never push objects of any kind give some undesirable damage to
into this product through open- other unit.
ings as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.

14. Attachments
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards.

6
 Introduction
15. Accessories e) If the product has been dropped

Before Using
Do not place this product on an or damaged in any way.
unstable cart, stand, tripod, brack- f) When the product exhibits a dis-
et, or table. The product may fall, tinct change in performance - this
causing serious injury to a child or indicates a need for service.
adult, and serious damage to the
product. A product and cart combi- 17. If glass components, in-
nation should be moved with care. cluding lens and lamp,
Quick stops, excessive force, and should break, contact your
uneven surfaces may cause the dealer for repair service.
product and cart combination to
This product incorporates glass
overturn.
components, including a lens and
a lamp. If such parts should break,
please handle with care to avoid
injury and contact your dealer for
repair service. The broken pieces
of glass may cause to injury. In
the unlikely event of the lamp rup-
S3125A turing, thoroughly clean the area
around the projector and discard
16. Damage Requiring Service any edible items placed in that
Unplug this product from the wall area.
outlet and refer servicing to quali-
fied service personnel under the 18. Servicing
following conditions: Do not attempt to service this
a) When the power-supply cord or product yourself as opening or
plug is damaged. removing covers may expose you
b) If liquid has been spilled, or ob- to dangerous voltage or other haz-
jects have fallen into the product. ards. Refer all servicing to quali-
c) If the product has been exposed fied service personnel.
to rain or water.
d) If the product does not operate
normally by following the operat-
ing instructions. Adjust only those
controls that are covered by the
operating instructions as an im-
proper adjustment of other con-
trols may result in damage and will
often require extensive work by a
qualified technician to restore the
product to its normal operation.

7
IMPORTANT SAFETY INSTRUCTIONS (Continued)

19. Replacement Parts 22. Do not use the product in

When replacement parts are re- a closed installation state.
quired, be sure the service techni- Do not place the product in a box
cian has used replacement parts or in any other closed installation
specified by the manufacturer or state. Otherwise it may overheat.
have the same characteristics as This could result in a risk of fire.
the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Replacement of the lamp only
should be made by users.)

20. Safety Check

Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to determine that
the product is in proper operating
condition.

21. Do not leave thermalpaper

documents or easily de-
formed items on top of the
unit or near the air exhaust
for long periods of time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.

8
POWER SUPPLY CORD SELECTION
If your line voltage is 220 to 240V, use one of the following types of cable.

Before Using
Plug Plug
configuration Plug type Line voltage configuration Plug type Line voltage

EURO 220 240V Australian 200 240V

240V
10A

Switzerland 200 240V

UK 220 240V 240V
6A
Use a 5A fuse which is approved by ASTA
or BSI to BSI362. North American 200 240V
Always replace the fuse cover after 240V
changing the fuse. 15A

IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection, repack the set as it was originally packed at
the factory.

Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the lens and the crucial internal parts. To prevent the unit from possible damage, do not
use the unit for at least 2 hours when there is an extreme or sudden change in tempera-
ture.

Place and Manner of Installation

• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
• Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts in the instrument. If you continue to use
it in that situation, the malfunction may result. Ensure to wait until the condensation natu-
rally disappears.
• In a high altitude location where air is thin, cooling efficiency is reduced so use the pro-
jector with [Fan mode] set to [High].

9
IMPORTANT PRECAUTIONS (Continued)
• The set of projector is hot after use. Handle with care.
• Do not use the projector while holding it in your hands or lap.
• Do not use the projector near a power source and the like, or in locations like a ship
or vehicle that are subject to vibration or shock. Doing so may lead to a malfunction or
shorten service life.

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the product’s precautions.

EXEMPTION CLAUSES
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from mal-
functions arising from combination with equipment or software that is not related to
Toshiba Corporation.

In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.
Model No. Serial No.
Retain this information for future reference.

10
OTHER CAUTIONS AND INFORMATIONS
Copyrights

Before Using
Showing or transmitting commercial imaging software or broadcast or cable-broad cast-
ing programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze functions, or displaying with the varying aspect ratio
of the images, could violate the direct or indirect copyrights of the imaging software or
broadcast program, etc., if done without first consulting with the copyright holder. For this
reason, please take appropriate measures before performing one of the actions listed
above, including obtaining a license from the copyright holder.

Disposal
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
This product contains substances which are harmful to humans and the environment.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.

Trademarks
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of Interna-
tional Business Machines Corporation.
• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas
Instruments.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other coun-
tries.
• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems
Incorporated.

Notational Conventions Used in This Manual

• References to pages with related information are annotated as follows.
For example, if making a reference to page 35:
• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.

11
REMOTE CONTROL BATTERIES
Caution
• Never throw batteries into a fire.

Notes
• Be sure to use AA size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of battery disposal.
• Do not mix different battery types or combine used batteries with new ones.
• If the remote control does not operate correctly, or if the operating range becomes re-
duced, replace both batteries with new ones.
• If the batteries are dead or if you will not be using the remote control for a long time, re-
move the batteries to prevent battery acid from leaking into the battery compartment.
Using the batteries improperly may cause them to explode or leak and lead to burn or in-
jury. If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water
and consult a doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using
tissue paper.
(Dispose of the used tissue paper as flammable garbage after moistening with water.)

12
CONTENTS
Before Using

Before Using
SAFETY PRECAUTIONS ..................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS ...........................................................................4
POWER SUPPLY CORD SELECTION .............................................................................9
IMPORTANT PRECAUTIONS ...........................................................................................9
EXEMPTION CLAUSES ..................................................................................................10
OTHER CAUTIONS AND INFORMATIONS ....................................................................11
REMOTE CONTROL BATTERIES ..................................................................................12

Preparations
Checking the package contents .......................................................................................15
Names of each part on the main unit ...............................................................................16
Names of each part on the control panel and remote control ..........................................17
Parts on the rear panel ....................................................................................................18
Preparing and using the remote control ...........................................................................19
Placement ........................................................................................................................20
Connection .......................................................................................................................22

Operations
Turning the power on and off ...........................................................................................23
Basic operations ..............................................................................................................25
Using handy features .......................................................................................................27
Using auto setting .........................................................................................................27
Correcting the keystone distortion ................................................................................27
Cutting off the picture and sound temporarily (Mute) ...................................................28
Freezing the image (Freeze) ........................................................................................28
Password function ........................................................................................................28
Using the menus ..............................................................................................................30
How to use the menus ..................................................................................................30
The image adjustment menu ........................................................................................31
The display setting menu ..............................................................................................32
The default setting menu ..............................................................................................33
Displaying Information (Status display) ........................................................................34

Maintenance
About lamp .......................................................................................................................35
Lamp replacement ...........................................................................................................35
Lens and main unit cleaning ............................................................................................38

Others
Trouble indications ...........................................................................................................39
Before calling service personnel ......................................................................................40
Specifications ...................................................................................................................41
List of general specifications ..........................................................................................41

13
Separately sold product ................................................................................................41
List of supported signals (RGB signals) .......................................................................42
List of supported signals (Y/PB/PR signals) .................................................................43
List of supported signals (Video, S-Video signals) .......................................................43
Pin assignment of COMPUTER IN & MONITOR terminals ..........................................43
CONTROL terminal ......................................................................................................44

14
 Checking the package contents
41 Please make sure that the following items are included in the box, along with the main unit.
42 If any item is missing, please contact the store immediately where you purchased the prod-
43 uct.
43
43
44 (1) (5)

(2) (6)

Preparations
(3) (7)

(4)

(1) Remote control (6) Power cord (See note)

(2) R6 (SIZE AA) batteries for remote (7) Carrying bag
control (2)
(3) CD-ROM
(4) Owner’s Manual
(5) RGB cable (3m)

Note
The shape and number of supplied power cords vary depending on the product destination.

The Supplied CD-ROM

The supplied CD-ROM contains an owner’s manual, including information not available for
the printed Owner’s manual (Getting started) and Acrobat® Reader™ to view the manual.
Installing Acrobat® Reader™
Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.
Follow the on-screen instructions.
Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader In-
staller. Follow the on-screen instructions to install the software.
Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner’s
Manual cover and list of bookmarks appear. Click on a bookmark title to view that
section of the manual. Click on p. to view a reference page with related information.
See the Help menu for more information about Acrobat® Reader™.

15
Names of each part on the main unit
(2)
(7) (6) (5) (4) (3) (1)

(8) (9) (8) (10) (11) (12) (13) (14) (15)

Back Front

Name : Function
(1) Lens : Projects expanded image.
(2) Infrared remote sensor : Senses commands from the remote control. p.19
(3) Foot adjuster release button : Press to set up or stow the foot adjuster. p.24
(4) Air exhaust : Expels air that has grown hot inside the projector.
(5) Control panel : Operates the projector. p.17
(6) Zooming lever : Adjusts screen size. p.24
(7) Focusing Ring : Adjusts screen focus. p.24
(8) Air intake : Draws in air from outside the projector.
(9) AC IN socket : Connect the supplied power cord here.
(10) Rear panel : Connects external devices. p.17
(11) Antitheft lock hole : Attach a safety cable or any other antitheft device.
(12) Speaker : Outputs audio sound.
(13) Tilt adjuster : Adjusts the projector’s horizontal tilt. p.24
(14) Lamp cover : Remove to replace lamp. p.36
(15) Foot adjuster : Adjusts the vertical projection angle. p.24

16
Names of each part on the control panel and remote control
Control panel Remote Control
(9) (8) (7)
Remote control
transmitter
POWER

(6)
(3)
(4 )
KEYSTONE +

(1)
KEYSTONE -
(5)
(3) (10)
(5) (2)
(2)
Battery

Preparations
cover
(4)
(11) (12)
(3)
(6) (1)
CAUTION
• Do not look into the laser light
source of the remote control or
direct the laser pointer toward a
person or a mirror.
• Handling and adjusting other
than described here may lead to
dangerous exposure to laser.

Name : Main Function

Control panel
(1) ENTER button : Accepts the selected mode.
(2) MENU button : Displays menus. p.30
(3) KEYSTONE button : Adjusts keystone distortion. p.27
(4) ON/STANDBY button : Turns the power on/off (standby). p.24
(5) INPUT button : Selects input. p.25
(6) Selection button : Menu selections and adjustments. p.30
(7) LAMP indicator : Displays lamp mode. p.24
(8) POWER indicator : Displays power on/off mode. p.24
(9) TEMP indicator : Lights when internal temperature too high. p.39
Remote control
(1) ENTER button : Accepts the selected mode.
(2) MENU button : Displays menus. p.30
(3) KEYSTONE button : Adjusts keystone distortion. p.27
(4) ON/STANDBY button : Turns the power on/off (standby). p.24
(5) INPUT button : Selects input. p.25
(6) Selection button : Menu selections and adjustments. p.30
(10) AUTO SET button : Sets up analog input from computer. p.27
(11) MUTE button : Cuts off the picture and sound temporarily. p.28
(12) FREEZE button : Pauses image. p.28

17
Parts on the rear panel
(1) (2) (3) (4) (5) (6)

(8) (7)
Name : Main Function
(1) MONITOR terminal : Connect to a computer display, etc.
(2) COMPUTER IN terminal : Input analog RGB signal from a computer or other
source, or a component video signal (Y/PB/PR) from
video equipment.
(3) S-VIDEO terminal : Input S video signals from video equipment.
(4) VIDEO terminal : Input video signals from video equipment.
(5) AUDIO IN terminal : Input audio signals.
(6) CONTROL terminal
RS232C :When operating the projector via a computer,
connect this to the controlling computer’s RS-232C
port. p.44

(7) AUDIO OUT terminal : Outputs audio signals.

(8) Antitheft lock hole : Attach a safety cable or any other antitheft device.

18
Preparing and using the remote control
■ Loading dry-cell batteries ■ Operating the remote
into the remote control control
 Remove the battery cover. Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.
• Operating the projector from the front

 Insert the dry-cell batteries.

Preparations
Be sure to align the plus and minus
Approx. 15
ends of the batteries properly. App
rox
. 5m

Two batteries (R6, SIZE AA) are used.

 Replace the battery cover.

Dry-cell batteries
• Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries with
new ones.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.

19
Placement
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting menu p.33 , in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

Ceiling-mounted front projection

Ceiling-mounted rear projection

WARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.

20
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
Screen As seen from above
projection size (inches)
a (min length) =
25.3807

90
projection size (inches)
a (max length) =
23.0947

Preparations
projection distance a (m)
projection height
size min length max length
(H)
(inches) (zooming (zooming (cm)
As seen from the side max) min)
34.67 1.36 1.50 7.9
Lens center
40 1.57 1.73 9.1
60 2.36 2.60 13.7
80 3.15 3.46 18.3
H 100 3.94 4.33 22.9
90
150 5.90 6.49 34.3
a 200 7.87 8.65 45.7
250 9.84 10.82 57.2
254.22 10 11 58.1

a is the distance (m) between the lens and the screen, and corresponds to a range of
1.36 m to 11 m. H is the height from the image bottom to the center of the lens.

21
Connection
Before connection
• Read the owner’s manual of the device you are connecting to the projector.
• Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal p.42 , etc.
• Turn off the power of both devices before connecting.
• The figures are sample connections.
• The MONITOR terminal outputs analog RGB signals or component video signals (Y/PB/
PR) from the COMPUTER IN terminals as selected with the INPUT button. If no input
is selected, the MONITOR terminal outputs the input signals last selected among the
COMPUTER terminals.
• A computer monitor usually cannot accept Y/PB/PR signals correctly.
Monitor

Computer (for control)

To video
output To audio
AV cable input p.44
(not supplied) To RS-232C
Audio cable
(not supplied) terminal

Control cable

AUDIO IN

S-VIDEO VIDEO CONTROL

MONITOR COMPUTER

AUDIO OUT

RGB cable AV cable

(supplied) (not supplied)
Audio cable
Computer (not supplied)
To RGB output To S-video
output

To audio output

Notes
• Moving pictures played back on computers using DVD software may appear unnatural if
it is projected with this projector, but it is not a malfunction.
• When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
• Output volume of AUDIO OUT terminal can be adjusted by the VOL button.

22
Turning the power on and off
■ Connecting the power cord
1 Insert the power cord connector into
the AC IN socket of the projector.
2 Insert the power cord plug into a
wall or other power outlet.
Power cord connector
■ Removing the lens cover (Supplied)

Be sure to remove the lens cover when the power is

turned on. If it is left on, it could become deformed due
to heat.

■ Turning the power on Control panel

Remote
Control
1 Press the ON/STANDBY POWER
Start-up screen
button.

Operations
The power turns on the green indica-
KEYSTONE +

tors light: POWER. After a moment, KEYSTONE -

the start-up screen appears.

CAUTION
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause dam-
age to your eyes or sight.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.

Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu p.32 .
• The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed p.25 .
• When [Key lock] is [On], the operation buttons of the projector do not work p.28 .
• When [Password] is [On], the start-up screen is displayed after the Password entry
screen disappears p.28 .

23
■ Turning the power off
1 Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)

2 Press the ON/STANDBY button again.

The screen turns off, but the internal cooling fan continues to operate for a short. Then
, the projector goes into standby mode.
When cooling lamp After cooling complete

POWER POWER

FLASH

A B C

During cooling ,the POWER indicator flashes.In this state,the power cannot be
A
turned back on.
If you are in a hurry, there is no problem with unplugging the power cord or turn-
ing off the main power switch in this state.
In standby mode
B

Note
• The projector consumes about 15W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
PRECAUTION
• If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in.

24
Basic operations
1 Turn on the power.
Turn on the power by following the instructions in “Turning the power on” p.23 .

2 Select the language (When using the first time).

When the projector is used for the first time after purchase,the start menu for
language(to display the menus and messages on screen) and confugration is dis-
played in English.(if the screen is out of focus,adjust it according to the step 6 .)
 Use the or button to select the English
desired language and press the button. German
Message for setup confirmation is displayed in a French
Italian
selected language.
Spanish
Portuguese
Chinese (traditional)
Chinese (simplified)
Japanese
Korean
Russian
Swedish
Turkish
Polish

Operations
Notes
• When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting menu p.33 ,
the start menu will be displayed the next time when the power is turned on.
• The language can slso be set via the Display setting menu p.32 .
• This owner’s manual assumes that English has been selected.

3 Activate the connected device.

Turn on and start the connected device such as a computer.

4 Press the INPUT button.

An image of the connected eqipment is projected.
Each time you press the INPUT button, it switches to the input of the connected equip-
ment that is outputting video signals.

Notes
• When [Auto input search] is set to [On] in the Default setting menu p.33 (factory
setting is [On]), the input is switched to the connected equipment that is outputting video
signals each time you press the INPUT button p.41 .

25
5 Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
 Lift up the front of the projector to 1

the desired angle, then press the

foot adjuster release button.
The foot adjuster extends. Release the but-
ton to lock the position.
 To adjust the horizontal angle, use
the tilt adjuster.
2
To stow the foot adjuster, hold up the projector
while pressing the foot adjuster release button,
then slowly lower the projector.

6 Adjusting the screen size and focus 1

 Use the zooming lever to adjust the screen size.

 2 Use the focusing ring to adjust the focus. 2

Notes
• Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.
• A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
• The DMDTM is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals p.42 , any resolutions not
supported by this projector (SVGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to SVGA resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
• If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” will appear.
• If a signal not supported by the projector is input, the “Unsupport signal” will appear.
• If an unavailable operation button is pressed, the icon will appear.

26
Using handy features
■ Using auto setting (Only for analog input from computer)
This function sets up the projector to the optimum state such as Remote
sampling phase, frequency, screen position, and clamp for each Control
type of the input signal by using simple operations.

Press the remote control’s AUTO SET button.

For computer input, the icon will appear during processing.

Notes
• The image may not be projected or auto adjustment/setting may
not be performed correctly for input signals other than those
supported by the projector p.41 , p.42 .

■ Correcting the keystone distortion

When the projector placement angle against the
screen is changed while projecting the image,
Control panel
the picture will undergo keystone (trapezoidal)
distortion. POWER

This projector is capable of correcting this key-

stone distortion.

Operations
KEYSTONE +

Before correction After correction

KEYSTONE -

Press the KEYSTONE or button.

27
■ Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be Remote
turned off. Control

Press the remote control’s MUTE button.

The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)
Notes
• The icon will appear while mute is in effect.
• Operating any other functions will also cancel the muting.

■ Freezing the image (Freeze) Remote

The image being projected can be frozen. This function is to be used Control
to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.
The picture pauses. (The Freeze function is released when
pressing the FREEZE button again.)

Notes
• The icon will appear while freeze is in effect.
• Other operation will also release the freeze.
• Even if an image is frozen on the projector, the pictures are
running on the video or other equipment.
• If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by
the copyright laws.
■ Key Lock
1 To enter key lock
Push and hold MENU button 5sec.
2 To exit from key lock
Push and hold MENU button 5sec.
If push any key durig key locking, display key lock icon.
• Protect from operating errors by locking on the control panel buttons of the
projector(The remote control operation are available)
■ Password function
How to set password (from [Off] to [On])

28
Using handy features (Continued)

1 Select [Password] in the Default setting menu and press the

button.
The password setting screen is displayed
2 Select [On] and press .
3 Enter a 4 digit number for the password using numeric key of the
remote control.
The input number appears as [****].
4 Re-enter the same password for confirmation.
When the password is confirmed the setting is complete and the password be-
comes [On].
If the password is wrong repeat the procedure from step 3 .

How to operate when password is [On]

1 Turn on the power.
2 The lamp lights and the password entry screen appears.
3 Enter the password using numeric keys of the remote control.
If the entered password is correct, the start-up screen appears and the projec-
tor goes into normal operation. If the password is wrong, a message appears to

Operations
prompt you to re-enter the password. If you enter a wrong password for more than
5 times, the projector will automatically power off and enter standby mode.

How to cancel password (from [On] to [Off])

1 Select [Password] in the Default setting menu and press the
button.
The password entry screen is displayed.
2 Enter the password using numeric key of the remote control.
3 Select [Off] and press the menu button.
The [Password] is canceled and becomes [Off].

Note
• The password entry screen appears when the power is turned back on only after
the power cord is unplugged.

If you forgot the password, please inquire your dealer.

29
Using the menus
You can call up on-screen menus, and conduct a number of adjustments and settings us-
ing the operation buttons p.17 on the control panel (main unit side) and remote control.

■ How to use the menus

The menu shown below is for operation instructions purposes and might differ from the
actual display.

1. Press the MENU button Display the Setting display menu.

2. Select a Category
Select a category by using .
There are following five
categories: Displays the current
adjustments and settings of
Image adjustment menu
selected category.
Display setting menu Item shown with gray cannot
be adjusted with the current
Default setting menu input source.
Status display menu

3. Adjustments & Settings Press the or button .

Item
Adjustment/Setting Value

These marks signify

the items can be
adjusted/set by using
5. End
. Press the MENU
button
The menu disappears.

These marks signify that

there are options.
These marks signify the items can
Press to display a
be selected from the list by using
list of options.
.
After an item is selected, apply it by
pressing .

The figure shows displays given for operation instructions purposes. As the display may
differ depending on the item, use the following pages as a reference.

4. Back
MENU button

30
■ The image adjustment menu
Use this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Analog (D-SUB)
Item Description Video S-video
RGB Y/PB/PR
Picture mode Toggle the picture mode with Yes Yes Yes Yes
/
Bright/Standard/True color(RGB)
Standard/Cinema
(Y/PB/PR,Video, S-video)
Correct the keystone (trapezoid) dis- Yes Yes Yes Yes
Keystone tortion of the screen.
Screen shrinking Screen shrink-
downward ing upward
Adjust the brightness of the image. Yes Yes Yes Yes
Brightness Darker Brighter

Contrast Adjust the image contrast. Yes Yes Yes Yes

Lower Higher

Operations
Color Adjust the color of the image. No Yes Yes Yes
Lighter Deeper
Tint *1 Adjust the tint of the image color. No No Yes Yes
Reddish Greenish
Sharpness Adjust the sharpness of the image. No Yes Yes Yes
Softer Sharper
H-position Adjust the horizontal position of the image. Yes No No No
Move left Move right
V-position Adjust the vertical position of the image. Yes No No No
Move down Move up
Phase Adjust with to eliminate flicker. Yes No No No
Frequency Adjust with to eliminate periodic patterns Yes No No No
and flickering when many vertical lines appear on
the screen.

*1: [TINT]can be displayed and adjusted only when the video signal is set to[NTSC]and[NTSC4.43].

31
■ The display setting menu
Use this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)

Item Description
Screen size
(Full): Display with 800 × 600 dot resolution
(Thru): Display with sampling resolution
(Wide): Wide-screen display
16:9 Posi- Adjust the vertical position of 16:9 image Lower Higher
tion
Back- Screen to display when there is n o input signal (Logo) (Blue)
ground (Black)
Icon Display icons as function guides On Off

Reset all Press .

Resets all adjustments and settings to their factory settings.
Yes No

Detailed description
[Screen size]
• If “Thru” is selected for [Screen size], portions exceeding the native resolution
(800 × 600 pixels) will not appear on the screen. Note that for RGB signals with
clock frequency 110MHz or lower, all input pixel signals are sampled. However,
if the clock speed is higher than this, the RGB pixel signal is thinned before
sampling.
• If you use the screen size setting function on commercial video software,
broadcast or cable-broadcasting programs to display images with the varying
aspect ratio except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
[Background]
• TOSHIBA is set for [Logo] by factory setting.

32
Using the menus (Continued)

■ The default setting menu

This menu shows placement status and other settings.
Item Description
Projection Sets projection mode in accordance with Placement Style.p.20
mode (Ceiling) (Rear ceiling)
(Standard) (Rear)

Auto input Set whether the input with signals is only selected or not.
search On Off
Language Select one of the languages below to use for displaying the menu
and messages
[ : Enter setting mode] [ :Selection] [Apply: ]
English/Français/Deutsch/Italiano/Español/Português/
/Svenska/Türkçe/Polski/ / / /

Fan mode Sets the cooling fan speed.

Standard High
Lamp power Sets the lamp power.
Low Standard
Password Password function p.28 On Off
When [Password] is [On], the Password Setting screen is displayed.

Operations
Power on Sets whether to turn on the power when the ON/STANDBY button is
pressed (Manual), or when the power cord is plugged in (Auto).
Manual Auto
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use
the projector, for example, at high altitude (over 1,500 meters above sea level).
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.

33
Using the menus (Continued)

■ Displaying Information (Status display)

This displays information about the input signal,lamp use time,etc.

“Yes”: displayed, “No”: not displayed

Item Description Computer Y/PB/PR Video S-video
Input Input source name Yes Yes Yes Yes
Resolution Resolution (in dots) Yes No No No
Video mode Color method of video signal No Yes Yes Yes
Picture mode A group of Pre-set display mode Yes Yes Yes Yes
Lamp time Time of lamp use [Note 3] Yes Yes Yes Yes
Version Firmware version [Note 4] Yes Yes Yes Yes

Notes
1: The mode of supported RGB signals p.42 is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult
with a store about getting a TLPLV6 replacement lamp (sold separately) prepared.
4: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.

34
Maintenance
About lamp
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at the
expiration of its life.
• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
• Burst is likely to happen if the lamp is used after the replacement period has elapsed.
• When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.
■ Immediately replace the lamp when a sign appears on the screen.
• When the replacement time approaches, a message will appear on the screen.
• The risk of burst will increase if the lamp is continuously used without being replaced.
• Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”. p.34 )
■ When the lamp is broken
• If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
• In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area.
• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes
or you breathe it.

Lamp replacement
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one.

Maintenance
WARNING
• If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealer-
ship when the lamp has to be exchanged.
Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger
of damage from falling pieces of glass if the lamp is broken. Besides, working at high
elevations can also be hazardous. Do not attempt to replace the lamp by yourself.
• When replacing, always use lamp “TLPLV6” (sold separately).

CAUTION
• If you have been using the projector, the lamp will be very hot, and may cause burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken pieces and
contact your dealer for repair service.

35
Lamp replacement (Continued)

1 Unplug power cord.

2 Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.

3 Remove the lamp cover. 3 Lamp cover

Loosen the two screws, raise the outer lamp 1

cover with your fingers as shown to remove
the outer lamp cover. Use care to avoid any
damage to nails and/or tip of your finger(s). If
you have any difficulty in removal, you can use
a screwdriver or any other smaller tool for your
convenience.

4 Pull out the lamp. 4

1

Loosen the two lamp locking screws, pull up the

handle to remove the lamp. 2

5 Mount the new lamp. 5 2

Align the orientation, press down the new lamp
until the bottom is reached, and lock in place using
1
the two lamp locking screws.

6 Replace the lamp cover.

Align the cover,and press it in,then tighten the
screws loosend in step 3 until the lamp cover is
no longer loose.

36
7 Reset the lamp timer.
See the lamp’s manual for instructions on resetting
the lamp timer.

Notes and Precautions

• It is recommended that the lamp be replaced after 2,000 hours of use.When [Lamp time]
reaches 2,000 hours,the icon and a message will appear. (After 2,000 hours, they will
appear when the power is on at the first time every 100 hours.) This display disappears
when you press the button.
• Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly,
the projector may fail to be powered on or the lamp may fail to come on.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic mer-
cury. Be careful not to break used lamps, and dispose of them in accordance with local
regulations.

Maintenance

37
Lens and main unit cleaning

WARNING
• Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.
Attempting to clean/replace the lamp at a high site by yourself may cause you to fall
down, thus resulting in injury.

■ Lens cleaning
• Clean the lens with a commercially available blower and/or
lens cleaner.
• The lens is easily scratched, so do not rub it with hard objects,
or strike it.

■ Main unit cleaning

• Clean the main unit after unplugging the power cord.
• Wipe dirt off the main unit gently with a soft cloth.
• Do not wipe the main unit with a damp cloth. Doing
so may allow water to get inside, resulting in an
electric shock or failure.
• Do not use benzene, thinner and the like as they
may deform or discolor the unit or damage the paint
surface.
• When using a chemically treated cloth, follow the
precautions included with the cloth.

38
Trouble indications
The indicator lights inform you of interminal abnormalities.

No power
POWER
⇒ Problem with projector
• Unplug the power cord, and contact your dealer.

Lamp went out during use, or won’t come on

⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of
POWER
the lamp has ended or the projector is malfunctioning.
(Red lit) • Unplug the power cord and wait for a short while, then turn the power
(Red lit) back on.
• If a lamp burns out, replace it with a new one.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not
POWER blocked.
• Unplug the power cord and wait for a short while, then turn the power
back on.
❈ The icon will appear before the power goes out.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
POWER ⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
❈ The icon will appear before the power goes out.
FLASH
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
⇒ Problem inside the projector.
POWER
• Unplug the power cord and wait for a short while, then turn the power
back on.
FLASH FLASH • If the above action will not clear the problem, unplug the power cord,
and contact your dealer.
❈ The icon will appear before the power goes out.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Others

39
Before calling service personnel
If you think something is wrong, check the followings before contacting customer service.
Please see “Trouble indications” p.39 as well.

If This Happens Check

No power • Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover attached properly? p.36
Power goes out • Is the ambient temperature high? p.39
during use • Is the air intake or air exhaust blocked? p.39
No picture • Is the mute function on? p.28
• Is the brightness setting minimized? p.31
• Are the connections set up correctly? p.22
• Are all the connected devices functioning properly?
No audio • Is the mute function on? p.28
• Are the connections set up correctly? p.22
• Are all the connected devices functioning properly?
Picture not • Is the input signal supported by the projector? p.42 , p.43
displayed • Is there something generating an abnormal video signal, for
correctly instance the video tape?
Picture blurred • Is the lens dirty? p.38
Part of picture • Is the lens focus adjusted optimally? p.26
out of focus • Is the projection distance within the projector’s supported range? p.21
• Is the projector’s screen placement angle tilted too far? p.21
Image is dark • Are the brightness or contrast adjustments off? p.31
• Is the lamp nearing the end of its service life? p.34
Colors too light • Are the color, tint adjustments off? p.31
Bad shading • Is the screen dirty?
• Is the lamp nearing the end of its service life? p.31
Control panel • Is the key lock function on? p.28
key doesn’t work
Remote control • Are the remote control’s batteries drained?
doesn’t work • Are the batteries inserted into the remote control correctly? p.19
• Is the remote control being used within the effective range? p.19
• Are there any obstructions between the remote control and
projector?
• Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?

40
Specifications
■ List of general specifications
Item Specification
Consumption Power 275 W
Weight 2.0 kg
External Dimensions
239 x 107 x 207 (W x H x D)
(including protruding parts)
Cabinet material PC+ABS resin and ABS resin
Conditions for usage environ- Temp: 5°C to 35°C; relative humidity: 30% to 70%
ment
Display pixels 1 chip DMD™
Picture elements 480,000 pixels (800H × 600V)
Lens Zoom lens F=2.7-3.0 f=21.81-23.77 mm
Lamp High-pressure mercury lamp (200 W)
Projection screen size 34.67-254.22 inches
Projection distance 1.36-11m
Speaker 2W
CONTROL terminal RS-232C: Mini DIN 8 pin
COMPUTER(Y/PB/PR)
Mini D sub 15 pin Analog RGB / Y/PB/PR (dual use)
Connection terminal

IN terminal
VIDEO terminal S-VIDEO: Mini DIN 4 pin
VIDEO: RCA Pin Jack
AUDIO 3.5mm dia stereo mini-jack
MONITOR terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)
AUDIO OUT terminal 3.5mm dia. stereo mini-jack

Notes
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added
in the future.

■ Separately sold product

Others

Replacement Lamp Model TLPLV6

41
Specifications (Continued)

■ List of supported signals (RGB signals)

This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Refresh rate H-frequency Clock
Resolution Mode [Hz] [KHz] (MHz)
VGA_60 59.94 31.46 25.17
VGA_72 72.8 37.86 31.5
640x480
VGA_75 75 37.5 31.5
VGA_85 85 43.26 36
720x400_70 70 31.5 32
720x400
720x400_85 85.03 37.92 35.5
SVGA_56 56.25 35.15 36
SVGA_60 60.3 37.87 40
800x600 SVGA_72 72.18 48.07 50
SVGA_75 75 46.87 49.5
SVGA_85 85.06 53.67 56.25
XGA_60 60 48.36 65
XGA_70 70.06 56.47 75
1024x768
XGA_75 75.02 60.02 78.75
XGA_85 84.99 68.67 94.5
1280x1024_60 60.02 63.98 108
1280x1024
1280x1024_75 75.02 79.97 135
1152x864_70 70 63.85 90.3
1152x864 1152x864_75 75 67.5 108
1152x864_85 84.99 77.09 130
1280x960_60 60 60 108
1280x960
1280x960_75 75 75 120
1400x1050 SXGA + 60 63.98 118
832x624 MAC 16” 74.55 49.725 57.28
1024x768 MAC 19” 75 60.24 79.85
1152x870 MAC 75.06 68.68 81
640x480 MAC G4 60 31.35 40
1024x768 i Mac DV 75 60 79
1152x870 i Mac DV 75 68.49 80.05
1280x960 i Mac DV 75 75 120

Note
• Signals which resolution exceeds the native resolution (800 × 600 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.

42
■ List of supported signals (Y/PB/PR signals)
Signal format fh(kHz) fv(Hz)
* 480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
* 576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00

■ List of supported signals (Video, S-Video signals)

Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43

■ Pin assignment of COMPUTER IN & MONITOR terminals

5 1
Pin Pin description
No. During RGB input During Y/PB/PR input
1 Video signal (R) Color difference signal (PR)
2 Video signal (G) Luminance signal (Y)
3 Video signal (B) Color difference signal (PB)
10 6 4 N.C ∗
15 11 5 GND ∗
6 GND (R) GND (PR)
7 GND (G) GND (Y)
Mini D sub 15 Pin connector 8 GND (B) GND (PB)
Input Signal 9 +5V ∗
• RGB input 10 GND ∗
RGB signals: 0.7V (p-p) 75 Ω 11 N.C ∗
Horizontal sync signal: TTL level (Pos/neg polarity) 12 SDA ∗
Vertical sync signal: TTL level (Pos/neg polarity) 13 Horizontal sync signal ∗
• Y/PB/PR input
Others

14 Vertical sync signal ∗

Y signal: 1.0V (p-p) 75 Ω 15 SCL ∗
PB/PR signals: 0.7V (p-p) 75 Ω
∗ Do not connect anything.

43
■ CONTROL terminal
● Pin assignment
Pin No. Signal Name Description
7 1 RXD Receiving data
8 6 2 N.C No connection
3 N.C No connection
5 3 4 GND Signal ground
5 N.C No connection
4 6 N.C No connection
2 1 7 TXD Sending data
8 GND Signal ground
Mini DIN 8 pin connector

Notes
• Contact your dealer for control cable and commands.

44