GHOST6 ON SA Le FLYING BEAR FOR 3D PRINTER1.After unpacking, please check the model and quantity of spare parts. If there are any missing parts, please contact us in time, and we will send you the replacement parts as soon as possible. 2.Please pay attention to safety when assembling the printer or printing the model. 3.Please place the machine in a ventilated, spacious and dust-free environment; 4.Do not try to use the machine in a way not described in the instructions, so as to avoid personal injury and property damage. 5.Do not place the printer in a highly vibrating or other unstable environment, the shaking of the machine will affect the printing quality. 6.Do not touch the nozzle, hot bed and moving parts when the printer is working to prevent personal injury. 7. After printing, use the residual temperature of the nozzle to clean up the filament on the nozzle in time. During cleaning, use tools and do not touch them directly, Please wait patiently for cooling before taking out the model. 8.Do not wear gloves when operating the machine to avoid winding and extrusion of moving parts on person. 9.Please keep the printer and printer parts out of the reach of children to avoid personal injury. 10.Often do product maintenance, regularly clean the printer body with a dry cloth in case of power failure, and wipe off dust, bonded printing materials and foreign matters on the guide rail. 11.If you do not use the printer for a long time, please protect the printer from rain and moisture. 12.In case of emergency, please don't panic and turn off the printer directly. 13.Users shall abide by the laws and regulations of the corresponding countries and regions where the equipment is used, abide by professional ethics, pay attention to foreign matters, and prohibit the use of our products or equipment for any illegal purpose. In case of any violation, our company will not be responsible for the relevant legal responsibilities.1.Product Overview 01 2.Technical Specification 03 3.Packing list 04 4.Assemble 3D printer 06 5.Touch screen function 13 6.Hot bed leveling 1 8 7.First print 20 8.Software installation 2h 9.WiFi printing introduction 33 10.Equipment maintenance 37 11.Trouble-shooting 38 12.After-sale service 42 13.Overhaul circuit diagram 43@ Vlimit switch © YMotor © Xwotor @® Touch screen @ Xlimit switch © Ziimit switch @ Belt adjust @uss 01 © xvsett @ ZMotor @ Hot bed @ TF card @ Teflon tube © Bellows @® Door © Buzzer@ Extruder == @ Extrudermotor @ PcBwiringhamess @ Radiator fan @ Nozzle ® Model coolingfan Cover ® Belt adjust 8 © Filament detection sensor ® Power switch @ Filament supportTechnical Specification Product Model: Forming Size: Ghost6 255*210*210mm Molding Tech: Number Nozzle : FDM 1 Nozzle Diameter: Printing Accuracy: Standard 0.4mm. 0.05~0.3mm Print Material: Filaments: 1.75mmPLA PLA,ABS,TPU,HIPS, Wood Input file format: Rated Power: STL, OBJ, DAE, AMF 300w Bed Temp: Nozzle Temp: <110°C <275°C Ambient Temp: Resume Printing: 8°C~40°C Yes Printing Speed: Filament Detector: 20~150mm/s (recommend 60mm/s) Yes Connection Mode: Slice Software: TF Card, USB Port (not recommended) Cura Rated Voltage: Input:AC 110V/220V 50/60HZ Output:DC 24V 03@ GHosTs 1Pcs © Extruder assembly Filament detection sensor © Filament support @ PLA Filament Teflon tube (@Handie @ Magnet | © Wire clip a a M3*6 5PCS @ Teflon tube bracket lee ~ Eos a = ia ho @® Power cord @ mssipcs || @ maaipcs | | @ maeiecs | 04Packing list aie list an l @ Cover | | @ Hotend assembly @ USB cable \ i \ 7 | ae | ® Diagonal pliers @ Shovel Cc j | : | © Tweezers @® Needle ® Toolkit ® Tiexs stylusAssemble 3D Printer. We have provided you with Ghosté detailed installation video. You can search "FLYINGBEAR Ghost6 30 printer installation video.” in YouTube. You can also scan the QR code to get the video. Installation video 1.Installing door handles. Fix magnet and handle with countersunk head screw M4X8 screw. 06Assemble 3D Printer 2.Install extruder. Install the extruder and fix it with M3 *8 screws from both sides, install the extruder harness and fix the bellows with tie. (tighten the M3 *8 screws before making sure the plastic parts are flat ). 073.Install teflon tube bracket. Lock the teflon tube bracket with M3 "6 screws. 084.Install the filament detection sensor. install the filament detection sensor in the position shown in the picture. Support the filament detection sensor with your hand, lock the right side from the inside with m3*6 screws, the wiring harness of filament detection sensor pass through the internal square hole and is connected to the filament detection sensor. place the wire clip on the left wire harness and tighten itinternally with M3 “6 screws. og5.To install the Filament support. Just adjust the direction of the rack according to the weight of filament. The logo upward is suitable for 1kg filament and the logo downward is suitable for 2kg filament, 10Assemble 3D Printer 6.Install teflon tube. Insert one end of teflon into the extruder feed port and the other end into the filament detection sensor. 11Assemble 3D Printer The default input voltage is 220V. If you need to modify the input voltage You can use tools such as screwdriver to pull the internal switch Oo The input voltage mode can be modified on the left side of the printer base. Ifyou can't solve the problem, please contact us in time © You should watch the video carefully and patiently when you encounter problems. After-sale service: [email protected]Touch screen function CE) =O @OZ.0 8 eo Ge aoa SEB Beans Layerstop 100% nageticriprasg et CS ane 5BTouch screen function Etusion HotBed Godsend GD PLA o'r easements @D aes ua a = | amen — GD TP-UNK 9663, TP-UNK 9663 TP-UNK_ 9663, TP-UNK 9663, TP-UNK_9663| Flamer darter Vern @ sovotn a ape vate: a Supper entation Stensonch screen function be Layer a layerstop 100% =m ~ Sone st € Zotfset 100% a— aS Preheat © Temperature display. © Adjust nozzle temperature. fore © Adjust the temperature of the hot bed. © Preheating PLA. see) © Preheating ABS © Stop heating nozzle and hot bed.Touch screen function Move © XYZ current position. @ Controls the movement of XYZ axis. © XYZ returns to the origin at the same time. © Adjust the distance of each movement. © Tum off the stepper motor. Printing be @ Status bar. @ Print progress display. © Modify hot bed temperature. @ Modify print rate. © Modify nozzle print temperature. @ More functions @ Set the number of layers to stop. © Modify the extrusion amount of the nozzle. © Adjust Z-axis printing height. © Modify fan rotation rate. Filament © Continue Extruder food key. © Extruder feed / discharge key and current temperature display. © Heat the nozzle to 200 degrees. © Stop nozzle heating. 16screen function Layer to stop and Z offset © Set the number of layers to stop. © Save settings © Single offset © The total offset © Select offset direction © Move the nozzle to the corresponding 4 positions. © zaxis goes back to its origin. © Monitor the XYZ limit switch for proper operation. © Filament detection switch © Flame Sensor switch TempSetting and advanced © Proheating PLA @ Preheating ABS © Floodlight switch © 5010 fan switch iterate 17Hot bed leveling video. After installing the printer, make sure that all wires are connected without any problems. You can turn on the printer and follow these steps to level the printer. You can also scan the QR code to watch the hot bed leveling video tutorial. Hot bed leveling and first print video step1: Press the power switch, Select "move" in the main interface, and then click "XYZ" to return all three XYZ axes of the printer to the origin. ill a : ss EA osos © In the leveling process, the nozzle and hot bed must be separated by paper. Do not scratch hot bed or nozzle. step2: Click in the order shown below to open the leveling guide page. Click on the first point, the nozzle will move to the corresponding position, and then the gap between the nozzle and the hot bed will be adjusted by the spring. @Rotate the corresponding nut under the hot bed by hand so that the distance between the hot bed and the nozzle is the thickness of a piece of paper. (there is a resistance when pulling out the paper). 183)Do the same for the remaining 3 points. Keep the hot bed and nozzle at a distance of a piece of paper. Po 1 Paper Spring Hot bed nutAfter the hot bed leveling is complete, we can start printing a model and verify that the hot bed is actually leveled.(We take printed PLA filament as an example) 1.Preheat the nozzle. If your filament is PLA, click PLA. 2.Insert filament into the extruder. @The front end of trimming filament is 45 °. @Insert the filament into the filament detection sensor and enter the extruder through the Teflon tube . @Pry the extruder spring so that the filament can be inserted into the gear of the extruder, then through the extruder into the Teflon tube, and finally directly to the nozzle. @Rotate the knob of the extruder clockwise to compress the filament, and counterclockwise to loosen the filament. In the actual printing process, if the nozzle discharges normally, there is no need to adjust. 20First print 3.After confirming that the filament enter the extruder. After confirming that the filament enter the extruder, extrude the filament through the touch screen keys. Note that the temperature must be above 190°C. Click the feed arrow on the extrusion interface until the filament is extruded from the nozzle. oO OM == sa0rc/i90% . & Note: The feed length cannot be selected in continuous feed mode. To select the feed length of the extruder, you must turn off the continuous feed button to select the feed length. 4.Install the tf card, then return to the main interface. Install the tf card, then return to the main interface, and then select the model file in the printing interface. When the nozzle and hot bed are heated to the set temperature, the machine will start printing. If there is no printed file of screws and nuts in your memory card, you can scan this, QR code to download it by yourself. ‘Screw and nut.gcode 21After printing, hot bed will cool down slowly. Only after cooling can the model be removed. DIn the process of removing the model, be careful not to hurt your hand. 2)The model must be removed after the hot bed is cooled. Because the glass coating will lose its stickiness after cooling in the hot bed, it is easier to take the model. First raise a small hole with a shovel, and then shovel the whole model with a shovel. 22f the first layer prints as shown in Figure B, the distance between the hot bed and the nozzle is correct, you can print at ease. @If Aor C occurs, the Z compensation parameter can be adjusted during the printing process, Z+ is away from the nozzle, Z -is close to the nozzle. 23scan the QR code to download the G-code file of the screw and nut model. After the filament are loaded, scan the QR code to download the G-code file of the screw and nut model, and then store it in the storage card. Slicing software installation video: 1.Download the latest slicing software first. Software download website https://ultimaker.com/software/ultimaker-cura (UIMaKET 2p somes seas pha lm Sr a] Ultimaker Cura 2.Follow these steps to complete the ing software installation. 24Software installationSoftware installation 26Software installation 3.Add printer After the software is installed, you need to add the printer according to the following steps. User Agreement Sign in to the Ultimaker platform Disclaimer by Uimaker Pease readtni deiner caret Except when otherwise stated in writing, Utimaker provides any 2 Lumar stare or third party software Ass" wtnout warranty ‘of any king. Te ene kaso the quality and petormance of Urimaer sofoaretewtn you. Lntess require applicable aw or agreedtoin wring, n no event Jn Utimaker be tabi you Tor damages inducing ay general, Tham towesny bce rete oer a4 cay treet naman, sentation 8 a ‘le After the introduction of the software solution, you will see the following setting interface. Please add and set the printer according to the following steps. Add a printer Add a printer ‘ets networked pnter . ‘festa networked printer Tere Sem pintr fund ore your eater, as yi (hasineron][sevecetrhocmm | | > vom IG ‘ssa non networked printer & z sc gem ove ! 27Software installation This sets the G-code code for the printer. [Beamer x Fying Bear cross Pinter Stings 8 Fill in the Start G-code Fill in the End G-code G21 M104 SO G90 M140 SO M82 M84 M107 M107 G28 X0 YOs G91 G28 ZO G1 E-1 F300 G1 Z3.0 F3000 G1 Z+0.5E5 G92 EO G28 X0 YO G1 X20 ¥20.0 20.28 F3000.0 M84 G1 X20 Y170.0 20.28 F1500.0 E12 G90 G1 X20.3 Y20.0 20.28 F1500.0 E18 M300 P300 S4000 G92 EO G1 21.0 F3000 M117 Printing G5 @ @ 28Software installation GB viactinesetinge x Flying BearGhost6 rte avuder Nozzle Settings gy Nox size “mm comparble mates diameter | [179] Nore fet x 09 Nez otter Y 00mm ‘ooking Fan Number ° Extruder Start G-code Extruder End G-code Release Notes 4.12.1 Bugfixes Update shapely to verson 1208hch among other things, ees muting objec on MacOS Monterey Fed 3 bugin Lightning inilwhere the infil eas protector under ets ‘reumetances 4.12.0 Foran ovewow of theme furs n Cora 12 plese wtch aurea Lightning nt The new ihn nl setting ts you opin high-quality top layers buts optimized tales materi anc increase your production speed. Spacal thanks rburems 2nd ager: Improved top surtace quality | Weve tweak the Monotonic setting and made acustments throughout Utimaker re profies This removes occasional scarraion medes animaroves too surace 29Software installation 4.Set print parameters After adding the machine, we need to set the slice parameters. GB nmacercre ie it wie settings Extensions Peferences He Cer mee) ore OOF ying bearcnons + | @ ween [| Fvng Bear chow & | [caper = oO General filament selection - PLA (we take PLA filament printing as an example). -— oo x —_o x = rare-0.2mm B20% Qor Lon a Print setngs x Print sting Eipromes om ar a oz oso 8 profie on faut OB 00000 non - txt Fieve-0.08 rm Bivvy —¢—_—_—_— Ee Qual train Cesta i EB Wall werma-a1senm top onto © & support BD Infill cara rast-o3 D Maer cose 4 sh Adnesion A Spee sercease-080m = tw can ie co ° Q IL ss 30Software installation = Cura parameter introduction SE Dratt-0.2mm 20% Qo on a Layer height: the printing = thickness of each layer is the key ee : parameter to determine the aoe La printing quality. It is usually set 2 = between 0.1-0.3. = quality = Layer 202 © walls : Filling density: the interior of the ee ba model is generally hollow. In order eee a to save materials, improve printing _ Top/eottom quality and printing success rate, Treomuseasstil 7 itis generally set to about 20%. Top Layers ‘ eno < Print temperature: sets the print @ infill temperature of the nozzle. PLA oe = is generally set at 190-220 °C ® matecat . and ABS is generally set at Poin Temperaure a 230-240 °C ul Pe Temperature ew Speed : oe ne Hot bed temperature: set the = Travel % Cooling hot bed temperature. PLA is &_ Support generally set at 40-60 °C and 5 RecomineniGed e ABS is generally set at 80-110°C. 31Software installation 4.Model slice After parameter setting, open the prepared STL file and slice it into gcode file. This process is slicing @Open STL file through slicing software. )Slice and save the file to TF card. —— ==, 32(9 ) Wifi printing introduction scan the QR code to download the G-code file of the screw and nut model. In addition to printing with an TF card,you can also using WiFi. Before using WiFi function, you must install the cura plugin first. You can follow the steps below to install the plugin. You can also scan the QR code to view the WiFi printing video tutorial. WiFi printing video 1.Follow the steps below to connect the printer to the router. @Open the wifi list, wait for a while, choose your own router signal. @Enter the password to get the IP address. ‘PALIN 9863 TP-UNK_ 983 TP-LINK_ 983 TPALINK_ 983 TP-LINK_ 983 The printers connects toa Feuterandyescancontal {hein from your INF nameTLINK 983 2.Scan the QR code to download the plugin"FlyingBearintegration". @Then open the Cura installation folder "plugins". (Find the folder according to the location you installed). Put the folder "FlyingBearintegration” in the folder "plugins". 33 im: MKS PluginWifi printing introduction Bo. ER Xs) 8s)! oo an peas cy see be hae core Ree aes loboxs crane ew open Sele ©» P> tasPc > winoxie (C3 > Program Files > UltimakerCura4t2> plugins YO sean. aa Datemosiies Type sue 1 codetier rowers xem power est AR iio epee: 2o1gjarr 1257 eR Hviies 201s 1257 sR © RBI agen ws! 2ee == 201997271553 ec) ROT eT ~ Won t0 x64 ore i257 RAR Bape soe ‘sis 3.After installing the plugin, restart Cura. (@/@After the plugin installation is complete, restart the slicing software, then open MKS WiFi. ©/@Enter the IP address displayed on the touch screen of the printer. @/d)Then open the WiFi control page, if the connection is successful, the temperature of the nozzle and hot bed will be displayed on the page. ta Drimaeeorcions yO mere rea ® « en coi nee SEL. Printers a | a Le Connect to Networked Printer eS nTWifi printing in |G utimaker cura = = Opa aa — “ss 4.Download the stl file, you can scan the QR code to download "screw and nut.stl" ‘screw and nut.stl Scan the QR code to download the stl file, then open the file with the slice software and click on the slice. ©/®after the slicing is complete, select "print over Flying Bear Ghost 6 " to upload the file to the printer. If "print jobs" is checked during the upload process, the printer will automatically start printing after the upload is completed. @/® If the file name exceeds 20 characters, the WiFi transmission will fail. If you encounter this problem, shorten the file name. 35Wifi printing introduction < Forto2mm — 20% Gor ton ~ Print setings eae ae Boi9fre 56 300K Supported Types Cips9 ~ oH 36The equipment needs regular maintenance. Equipment maintenance linear guides and T-shaped screws need regular maintenance. After 2 to 6 months of continuous use, if there is abnormal noise or movement is not smooth, you need to add grease or lubricant. 37Q The TF card cannot recognize or display the file? @The format of TF card is incorrect. The file must be in gcode format. @The TF card may be damaged during transportation. Please replace it with a new TF card. @Restart the printe. a The printer cannot return to the origin, or X/Y/Z makes noise during the return to the origin? @The motor wiring may be in poor contact. Please pull it out and insert it again. @n case of noise caused by long-term use, lubricate the guide rail and screw rod. @ When printing, the filament do not stick to the hot bed? @if the distance between the hot bed and the nozzle is too far, turn the hot bed adjusting nut clockwise on the unbonded side. @The whole hot bed is not leveled. Please refer to page 18-19 for specific operation. Printing speed is too fast, please reduce the “intial layer speed” to 60 when slicing. @f the appearance of the model is particularly complex, some solid glue can be properly applied on the hot bed.Trouble-shooting ® ‘The nozzle is too far away from the —x aenesay Assy platform, so the filament can not ‘adhere to the platform, SG S| lament are extruded eveniy, just sticking on the platform. ® ‘The nozzle is too close to the platform, eae and the filament are not extruded enough, ‘even scraping the platform, a Nozzle blockage during printing? @Heat the nozzle and clean the nozzle with a through needle. if the nozzle temperature is too low, increase the nozzle temperature (PLA s 230 °C). @The Teflon pipe is not inserted to the bottom. @Please check whether the print head fan rotates normally, if this happens after printing for a long time, the motor of the extruder may ‘overheat, reducing the printing speed. @lf the above method can not solve the problem, you can replace the nozzle, ‘scan the QR code on the Page 41 and watch the video of replacing the nozzle. 39Trouble-shooting The hot bed / nozzle temperature on the touch screen displayed as a negative value? @Poor contact of thermistor wire of hot bed / nozzle. @The thermistor wire of hot bed / nozzle is broken. @ How to solve the problem after the machine is turned on? 1.When the screen appears "Err: MAXTEMP PRINTER HALTED Please Reset”. @The thermistor of the hot bed is short circuit or the thermistor of the heating block is short circuit. 2.When the screen appears "Err: MINTEMP PRINTER HALTED Please Reset”. @The hot bed thermistor is disconnected. At this time, the hot bed temperature on the display screen is negative. It will not alarm when it is not heated, but will alarm immediately when it is heated. 3.When the screen appears “Heating Failed PRINTER HALTED Please Reset”. The thermistor of the heating block is disconnected. At this time, the temperature on the display screen is negative, and no alarm will be given when it is not heated. @The thermistor in the heating block falls off, and the display screen shows the temperature at room temperature. There is no alarm when there is no heating state @When the heating tube of the heating block is disconnected, the temperature on the display screen is displayed as room temperature without alarm in the non-heating state. @When the hot bed heating part is disconnected, the temperature on the display screen is room temperature, and there is no alarm when there is no heating state. Note: the interval between heating start and machine alarm is about 60s. 4.A black screen appears when the machine is turned on. The fan or heating tube is short-circuited. 5.When the screen appears“THERMAL RUNAWAY PRINTER HAL TED Please Reset’. @Generally, the temperature fluctuation is large, or the heating rod, thermal contact is not good, fell out. 40The extruder motor slips and makes an abnormal sound, grinding filament, Please look at page 38-40. if the nozzle temperature is too low, increase the nozzle temperature (PLA < 230 °C). @The printing speed is too fast. Please reduce the printing speed. @Check whether the nozzle is blocked, refer to Clause 4. a“Menem Menem A @ Heating rod Le oe oe @ 4010 Fan © Nozzle thermistor ‘it enc © 3010 Fan int svi int sich \ te Cy f a Error | [= romney] FT capac (sie)FLYING BEAR 2 oe Pe fe ia ne mee meet Version: English 2.0