Scribd
Upload
9 views

Stainless FC Tig

Uploaded by

jiao long
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

Stainless FC Tig

Uploaded by

jiao long
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

U.S. ALLOY CO.

STAINLESS STEEL dba Washington Alloy


7010-G Reames Rd.
Flux Coated Tig Charlotte, NC 28216
www.weldingwire.com

Quality Management System


in accordance with
ISO 9001:2000
Cert # 05-R0925 ALLOY DESCRIPTION AND APPLICATION;
These flux coated rods are primarily used for the root pass
on piping where backing and purging gas may not be possible or desirable. This 39” rod
should be used as a basic tig rod on DCEN, however caution is advised due to the easily
removable slag covering that must be removed prior to addition welding.

TYPICAL GTAW WELDING PROCEDURES; DCEN


Wire Diameter Amps Volts
5/64” 90-180 12-13
3/32” 150-250 12-13
1/8” 200-375 12-14

Procedures may vary with change in position, base metals, filler metals, equipment and other
changes.

TYPICAL UNDILUTED METAL CHEMISTRY (%) per AWS A5.22;

Chemistry
Grade 1) Intended Use
C Cr Ni Mo
R308L 0.03 18.0-21.0 9.0-11.0 0.50 Welding of 18Cr & 8Ni such as 304, 304L
R308H3 ) 0.04-0.08 19.5-22.0 9.0-11.0 0.50 Welding of 18Cr & 8Ni such as 304, 304H
R309L 0.03 22.0-25.0 12.0-14.0 0.50 Welding of carbon steel to austenitic stainless
R316L 0.03 17.0-20.0 11.0-14.0 2.0-3.0 Primarily use on 316 or 316L
R347 2) 0.08 18.0-21.0 9.0-11.0 0.50 Primarily use on 347
1) All grades has the following : Mn=0.50-2.5, Si=1.2, P=0.04, S=0.03 Cu=0.50 Single values are maximum
2) R347 also has Cb+Ta =8xCmin. -1.0 max.
3) R 308H is not listed in AWS; the chemistry is from E308HTO-3 per AWS A5.22 which provides higher strengths at elevated
temperatures.
AVAILABLE SIZES: TFT 308L= Rods of 3/32, 1/8
TFT 308H= Rods of 3/32, 1/8
TFT 309L= Rods of 3/32, 1/8
TFT 316L= Rods of 5/64,3/32, 1/8
TFT 347 = Rods of 3/32, 1/8
SPECIFICATIONS: Washington Alloy per AWS for stainless flux cored rods chemistry only

EAST COAST GULF COAST WEST COAST


7010-G Reames Rd 4855 Alpine Drive #190 8535 Utica Ave
Charlotte, NC 28216 Stafford, TX 77477 Rancho Cucamonga, CA 91730
Tel (888) 522-8296 Tel (877) 711-9274 Tel(800)830-9033
Fax (704)598-6673 Fax (281)313-6332 Fax (909)291-4586
6-2009 DC

Washington Alloy Company believes that all information and data given is correct. Use this information to assist in making your
own evaluations or decisions and this information should not be mistaken as an expressed or implied warranty. U.S. ALLOY CO.
assumes no liability for results or damages incurred from the use of any information contained herein, in whole or in part.
.

You might also like