MAINTENANCE 4.

3 FLUIDS AND LUBRICANTS

4.3 FLUIDS AND LUBRICANTS

4.3.1 LUBRICANTS FOR OPERATION IN COLD AND ARCTIC CLIMATES

Lubrication Point Lubricant Ambient Temperature °C

Hydraulic System Shell Tellus Arctic 32 - 50 to + 35

(pre-heated) ESSOTRANS EXTRA - 50 to + 28
Travel Gears Shell Omala HD 220 All seasons

Final Drives Shell Omala HD 220 All seasons

Swing Gears Shell Omala HD 220 All seasons

Track Rollers and Idler Wheels Shell Omala HD 220 All seasons

Pump Distributor Gears Shell Transaxle Oil 75W-90 All seasons

(pre-heated) Tranself Synthese FE 75W-90 - 45 to + 35

Pump drive shaft housings on

Shell Tellus Arctic 32 All seasons
the Pump Distributor Gears

Brake housings and Motor

Shell Tellus Arctic 32 All seasons
adapter housings of Gears

Fan Bearing Housings of Radia-

Shell Omala HD 220 All seasons
tor and Hydraulic Oil Coolers

Fuchs Stabyl L-TS MO - 10 to + 35

Central Lubrication System Shell Darina XL 102 Moly - 30 to + 35
Fuchs Urethyn HGO - 50 to - 10

Shell Malleus GL 400 - 10 to + 35

Swing Circle Lubrication System Shell Malleus GL 25 - 30 to 0
Fuchs Urethyn HGO - 50 to - 10

Refrigerant Lubricant Shell Clavus Oil R 68 - 50 to + 35

Refrigerant Shell R 134 a - 50 to + 35

Engine Oil SAE15W-40 API Category CG-4SH All seasons

Flexible Coupling SAE15W-40 API Category CG-4SH All seasons

Refer to ENGINE OPERATION AND

Engine Coolant and Fuel MAINTENANCE MANUAL for
Specifications.

277
4.3 FLUIDS AND LUBRICANTS MAINTENANCE

4.3.2 FLUIDS AND LUBRICANTS FOR MODERATE AND HOT CLIMATES

Ambient
Point of Viscosity Quality Grades
Lubricant Temperature
Lubrication Grades DIN/API
°C

Refer to ENGINE OPERATION AND MAINTENANCE MANUAL for

Engines
Specifications of Engine Oil, Coolant and Fuel.

- 20 to + 11 22
Hydraulic oil
HLP or -14 to + 21 32
HLPD
Hydraulic System - 6 to + 31 46 DIN 51524 T.2 and T.3-HLP
with ZINC
anti-wear 0 to + 40 68
additives *1)
+ 5 to + 48 100

Travel gears, Final

drives and Swing Gear oil CLP DIN 51517
gears -15 to + 50 CLP 220
*2) 3 - CLP

Brake housings and Engine oil SAE 10

Motor adapter hous-
all
ings of Travel Gears or Hydraulic oil HLP 32 DIN 51524T.2 and T.3- HLP
and Swing Gears *3)

PTO’s (Pump distrib-

utor gears) Gear oil CLP DIN 51517
-15 to + 50 CLP 150
*2) 3 - CLP
Pump drive shaft
Hydraulic oil all HLP 32 DIN 51524T.2 and T.3- HLP
housings on PTO

Fan bearing hous- DIN 51517

ings of Radiator and Gear oil CLP all CLP 220 3 - CLP
Hydraulic oil coolers

NOTICE
● *1) DO NOT mix ZINC-FREE Hydraulic oils with Hydraulic
oils containing Zinc. DO NOT mix Mineral Hydraulic oils
with Synthetic Hydraulic oils.
Mixing of the above oils, will reduce anti wear properties
and oxidation stability of the oil. Quick plugging of the oil
filters in the hydraulic system will occur.

● *2) Refer to the chart GEAR OILS filed in volume 2 binder

for the released gear oil qualities and viscosity grades.

● *3) Brake housings of swing gears manufactured by L&S

have no separate oil compartment, as brake disks are
lubricated by splash oil from gear box.

● The lubricating instructions in this book refer to the

recommended grade specifications. Damages caused
by using lubricants other than specified are not covered
by the manufacturer's warranty.

278
MAINTENANCE 4.3 FLUIDS AND LUBRICANTS

Ambient Quality Grades

Point of Viscosity
Lubricant Temperature
Lubrication Grades
°C DIN/API

Grease Fittings
(manual lubrication) Refer to the Lubricant Chart in volume 2 binder for the recommended
Multi-Purpose
Multi-Purpose Greases. The part numbers of recommended Multi-
Central Grease ”MPG”
Purpose Greases are listed in the Parts Catalog.
Lubrication System
Swing Circle Teeth Refer to PARTS & SERVICE NEWS, Bulletin No. AH00519 in volume
(manual lubrication) 2 binder for the recommended Adhesive Lubricants.
Adhesive
The part numbers of the recommended Adhesive Lubricants are
Swing Circle Pinion Lubricant
listed in the Parts Catalog.
Lubrication System

Track rollers, DIN 51517

Gear oil all CLP 220
Carrier rollers and 3 CLP
”CLP"
Idler wheels

Flexible couplings Engine oil API all SAE 15W-40 API Category CG-4SH

Air conditioning R 134a

Refrigerant
system
REMARK
The Air Conditioning is prepared for
Refrigerant Special oil Refrigerant ”R134a” only.
compressor See Note below. Observe Notice below.

NOTICE
The Air Conditioning must be filled with refrigerant ”R134a”
through authorized Service Specialists only. DO NOT use
refrigerant ”R12”, otherwise serious damage on system com-
ponents could occur. The lubrication oil for the refrigerant
compressor must be compatible with ”R134a” refrigerant.

279
4.4 FILLING CAPACITIES MAINTENANCE

4.4 FILLING CAPACITIES

Unit or System Liter (approx.)

Engine cooling system 475.0

Engine oil pan 290.0

Engine oil reserve tank 580.0 (457.0 Refill)

Fuel tank 6400.0

Hydraulic oil reservoir 3900,0

Hydraulic system 5900.0

Flexible coupling between engine and PTO 1.3

PTO (Pump distributor gear) 150.0

Swing gears (Manufacturer L&S), each 42.0

● Motor adapter housing 0.6

Swing gears (Manufacturer Siebenhaar), each 60.0

● Motor adapter housing *1)

● Brake housing 0.2

Travel gears, each (Manufacturer L&S) 155.0

● Motor adapter housing 0.6

● Brake housing 0.5

Travel gears, each (Manufacturer Zollern) 120.0

● Motor adapter housing 0.6

Drive shaft housing, final drives, each 145.0

Track rollers, each 2.4

Guide wheels, each 2.9

Support rollers, each 4.0

Fan bearing housing of radiator *2)

Fan bearing housings of hydraulic oil cooler *2)

Water tank for hand wash sink in Operator’s cab 50.0

Water tank for windshield washer system 7.0

REMARK
Capacities listed above are approximate values.
For proper checking use level plugs, dipsticks, and inspection
openings, provided for this purpose.

*1) Fill up to level gauge marking.

*2) Fill up to lower edge of level plug opening.

280