Marcespe E-220

Product manual
Please read carefully before use
Beijing Marcespe Machinery Equipment Co.,Ltd

Preface

This fully intelligent computer inkjet printer adopts 10 . 1 -inch true color IPS touch
screen and 32-bit ARM embedded structure , runs embedded Linux system ,
provides unlimited storage of files , and is consistent with ordinaLj computers
in intelligence and ease of use. In terms of software , M C P takes cloud services
as the background platform , keeps pace with the times , combines network
and industrial manufacturing , integrates customers and manufacturers into
one , provides end-to-end , face -to-face intimate seviices , and shows the new
vision of leapfrog development of MCP inkjet printer technology with "remote
control syste" , and adopts key technologies such as coding stability control and
data protection on the circuit for multi-aspect innovation and optimization design.
It has powerful software editing features and extremely high stability. It is an
excellent product that combines technology and performance. It can accurately
print the production date , shelf life , batch number, model , spec ification ,
trademark and anti - counterf eiting mark , graphics , etc . on the sur f ace of food
, beverage , alcohol , pharmaceutical , wire and cable and other canned products
, plastic packaging , paper packaging products , etc .

Please read this manual carefully when using it to achieve the best results.
>>

1. Technical parameters

1.1 Physical
,●Machine size: 595X410X325 mm
● Machine weight: 24kg
Description
1. 2 I nstallation conditions
,Chassis:
● veDžical ; Sprinklers: Any direction
1.3 Conditions of Use
●Ambient temperature: 0 -40° C
● Ambient humidity: 0 -90% RH (no condensation)
1.4 Power supply
● Power supply: 1 10 - - 2 20± 1 0% VAC voltage , 60- 5 0HZ , 50W good grounding
1. 5 PeDŽormance parameters
● Printing:
Can be printed anywhere on the suDŽace of any material ;
It can print one to ǁve lines of information (5*7 dot matrix) ;

The character height (depending on the distance of the nozzle from the print , the
size of the character lattice and voltage) range is 1 .8 - 15MM

● Character dot matrix selection

English : 4 × 7 , 5 × 5 , 5 × 7d , 5 × 7 h , 5 × 7 i , 5 × 7 l , 5 × 7v, 5 × 7w, 8x12 , 7 × 9 , 7x9v, 7x10 , 8 × 16 ,
8 × 16C , 12× 16 , 12× 24 , 32x32
Chinese: 8× 8 , 10× 10 , 12× 12 , 16× 16 , 16× 16c , 20× 20 , 24× 24 , 32x32

● Printable characters can be selected

Arabic numerals: 0 -9;
English letters: a -z , A-Z;
Special symbols: =、 ' 、$ 、+ 、- 、/ 、 () 、 ; 、， 、？ 、% 、 ￥
Chinese characters: A complete libraLj of Chinese characters , which can be
edited directly on the inteDŽace

Va rious features:
,●can count the printed objects according to a sin gle piece or batch , and the
It
tomatic clock can be made;
Automatic control of printing speed ;
● Automatic control of ink viscosity;
●After being equipped with an external photocell and encoder, it can adapt to
conveyor belt speed to change the speed of printing.

After the external grating encoder is equipped , the print length can be ǁxed and
recorded ( metered) .

PAGE 01
 >>>

2.The principle and structure of the machine

2. 1 inkjet printing principle

This inkjet printer adopts inkjet oƺset inkjet dots and forms words.Var ious characters
can be composed of a ceDž ain lattice , as shown in Figures 1 and 2 .

1 1 2
1 2 3 4 5 6

Column spacing

Full column Empty column

Figure 1: Figure 2:
7x6 character matrix 16x12 character matrix

The pressurized ink enters the spray cavity, and the spray cavity i s equipped with a
cLjstal oscillator, and the vibration makes t he ink spray out through the micropores
and then turn from the in kline into ink spots. When the ink dot is disconnected , it
ǃies through the charging electrode to charge , the charged ink dot is deǃ ected by
the high-voltage electrode plate , the amount of charge determines the size of the
deǃ ection , and the ink dot ǃies out and falls on the suDŽace of the printed object.

A character is composed of a series of ink dots , which can be full and empty or in
between; The object moves perpendicular to the direction of the ink dot deǃ ection
to form columns spaced to form characters. The uncharged ink dots fall into the
recycling tube for recycling , as shown in Figure 3 .

PAGE 02
 >>>

Suction valve Bleed valve

Ink feed valve Gutter valve

Piezo drive signal Drop generator

Drop generator holding screws

Charge electrode
HV Deflection plate
Gutter

Figure 3 .Schematic diagram of the print head structure

2.2 Machine shape structure

Main view
Right view

Front of nozzle Nozzle side

Overview ofthe printer structure

PAGE 03
 >>>

2.3Structural drawing

Structural drawing

PAGE 04
 >>>

E-220 CI J PRINTER INK FLOW CHART

5

PAGE 05
10 8
Ink line
2.3 Ink pipeline diagram

Solvent L in e
M ix ing line
Recovery li n e
1 .Ink filte r 2 .Solvent fi lte r 3 .Negat ive pressure 4 .Ink valve 5 .Add valve
7 .Recovery pump 8 .V iscomete r 9 . Current lim it e r 10 . P re-pump fi lte r 11 . 12 .Posit ive pressure
13 .Solvent pump 14.Ink pump 1 5 . Ma in ink fi lte r 16 .Ma in pump 17 .P ressure balance 18 .Recovery valve
19 . Head flush valve 20 . Head feed valve 21 .Purge valve 22 . Nozzle 2 3 . Gutte r 2 4 . Nozzle fi lte r
B
 >>>

3. Installation and debugging

3. 1 Machine erection
3. 1. 1 Install the nozzle bracket, install the nozzle , and the photoelectric switch is ǁ rmly
installed on the bracket according to the movement direction of the product , and the
main engine and nozzle bracket conduit s hall not vibrate.

Requirements: The ground on which the machine is placed should be ǃ at and hard.
The machine has at least 1 meter of space left and right in front and rear and is well
ventilated. There should be obvious words " ǁ reproof and waterproof " near the host
and nozzle. Ink and diluent are ǃammable products , so at least one bottle of carbon
dioxide ǁ re extinguisher should be placed within a radius of no more tha n 3 meters
of the main engine , and ǃ ammable materials should not be stacked.

3. 1.2 The main engine power plug is plugged into the outlet of the AC voltage regulator,
and the input plug of the AC voltage regulator is inseDžed into the 220V power supply,
and ensure that the grounding is good.

3.2. 1 Debugging steps After the machine is installed , there is no problem in visual
inspection , and you can debug according to the following steps:

3.2.2 Inject ink and diluent into the ink bottle and diluent bottle , respectively.

3.2.3 Press the host power switch , and after 20 seconds , the panel display prompts for
the password.

3.2.4 Set parameters and information and supply the in kline as described in
Chapter 4 . When the display screen returns to the main inteDŽace state , if there is no
ink in the return ink can , wait for the ink to be added and o bsedže that the ink pressure
should be 0 .28MPa.

3.2. 5 Return to the main menu, press ' Ink Supply' , after the process is over, click ' Inkjet
Open' , (the nozzle has ink droplets sprayed out) , use paper or work piece close to move
under the nozzle , you can obsedže the wipe and print situation. Adjust the " printing
height" and " printing speed" during printing to meet t he requirements.

PAGE 06
 >>>

3. 3 Precautions for staDž -up ink supply:

1. Before staDžing , there are too many stains such as washing nozzles , charging poles ,
detection poles , HV plates , negative plates , and recycling tubes. First open the nozzle
hood , rinse the nozzle , charging pole , detection pole , HV plate , negative plate , and
recoveLj tube with cleaning liquid. See Figure 11 . After the cleaning liquid evaporates ,
cover the spray hood and turn on the machine.

2. After the ink supply progress bar is completed , if the nozzle is blocked and the in kline
deviates from the recoveLj tube , please use the “Open up nozzle ” in ' Ink operation' , you
can use this function repeatedly until the recoveLj tube can receive the in kline normally.

3. After ink supply, wait for the in kline to stabilize for 10 minutes , and o bsedže the break
point with a magnifying glass. You can judge the quality of in kline breakpoints based on
the following ǁgure 7 .

Poor jet Mediocre jet Good jet

break up point breakup point breakup point

Reference pictures for the quality of jet break up point

3.4 Precautions for shutdown:

1. Shutdown within 2 hours, please use quick shutdown.
2. Shutdown for more than 2 hours, please use cleaning shutdown (do not clean and
stop frequently, otherwise it is easy to cause ink thinning. Generally, the number of
cleaning times should not exceed three times a day. ）
3. If the shutdown is more than two weeks , please use the long shutdown cleaning of
ink road maintenance. (See below for details.)
4. Turn oƺ the power: Note: Turn oƺ the power but keep the plug powered.
5. After shutdown , use cleaning agent to clean the outside of the charging electrode ,
detection electrode , high-pressure plate , cathode plate , nozzle , etc. (can only be
cleaned with cleaning agent. ）

PAGE 07
 >>>

3. 5 Inkline position and break point adjustment

1. Inkline position adjustment: the machine is in the ink supply state (without high
pressure foundation) ;
( 1) The ink wire is in the middle of the charging groove;
(2) The visual distance between the in kline and the detection pole is 0 .5 - 1mm
(3) The bottom end of the in kline is in the middle of the recycling tube.

Adjustment method (in kline cannot be easily adjusted. If adjustment is required , it

is recommended to be peDŽormed by a s killed operator. ）：
( 1) Loosen the fastening screw of the spray cavity to make the spray cavity mov e left
and right with the ǁxed p in as the center;
(2) Or adjust the "front and rear " position adjustment screw of the spray cavity:
(3) O bsedže the position of the in kline with a magnifying glass

2. Inkline break point adjustment:

Judgment premise 1. ink viscosity is correct; 2. ink pres sure is correct; 3. in k pathis
smooth ; 4. in khas no deterioration;

3. The nozzle is not blocked

( 1) . After ink supply, run for 15 minutes;
(2) . O bsedže the break point with a magnifying glass. Adjust the break point
potenti ometer counterclockwise and o bsedže an in kline as shown in the ǁ gure 8 .

A.Jet breakup B.jet breakup C.Jet breakup

point is normal point is too high point is too low

Jet breakup point positioning inside the charge electrode

PAGE 08
 >>>

4. Operation guide and function introducti on

All the operation of the inkjet printer is realized through the touch screen , and the
10. 1 -inch true color screen shows the inteDŽace more direct operation process and
information content. As shown in the picture:

The soft keyboard is veLj straightforward to use , and can be entered and selected
directly on the inteDŽace. After booting up, there will be a login inteDŽace , users can
directly enter their user name and password , and then enter the main inteDŽace to
proceed to the next step.

It can also be used with a mouse and keyboard that is connected t o an external
computer.

PAGE 09
 >>>

4. 1 User main inteDŽace

Turn on the power and enter the user name and password to enter the main inteDŽace
of the system , as follows:

The ǁ rst time you turn on the machine , the user will be prompted for high-voltage
calibration, because the environment of each region is diƺerent , so it will have a
ceDžain impact on high voltage , so the ǁ rst thing after receiving the printer is to
peDŽorm high-voltage calibration.

The main contents of the inteDŽace:

1: System version number, time , and remaining maintenance time
2: 6 main menu options
3: Display of printed content
4: Counter, serial number 1 , 2 , real-time status and reset options
5: Printer status and some printing parameters
6: Printing real-time switch and 2 ink path operation options

PAGE 10
 >>>

1. Clean StaDž Jet

After clicking the function icon , the nozzle has ink lines sprayed out , and after
the nozzle is prepared , (if the "one -key power on and oƺ " has been turned on)
the system will automatically staDž printing , and the counter and serial number
will staDž counting. The “Clean staDž jet ”comes with a cleaning nozzle function ,
such as multiple "Clean staDž jet" will make the ink viscosity too low, you can enter
the ink operation to press fast “Quick StaDž Jet ” , after completion , the button
will become "Quick stop Jet" .

2. Clean shutdown:
After clicking the function icon , this function is used for more than 2 hours of
downtime. But no more than 3 times a day. After the execution , the nozzle ink
line stops , and automatically and thoroughly cleans the ink p ath components
such as the nozzle and recoveLj tube. When the printing is oƺ, the counter
automatically stops counting.

3. Printing switch :
This function is used to turn oƺ or turn on the o utput of the printing signal and
turn on the printing high voltage at the same time , click the function icon to
directly switch on and oƺ.

4. Power oƺ :

" Power oƺ " After clicking the function icon , after the shutdown completes
cleaning and shutdown , the power can be directly turned oƺ instead of the
hardware shutdown.

5. Serial number and reset:

Click the function icon serial number 1 to switch to serial number 2 , and then
click to switchback , press " reset" to reset the serial number or counter to the
lower limit they set.

6. More... :
Below the serial number, there are parameters related to printing or ink road ,
after clicking the function icon, you can switch to another parameter, and press
" More. . ." to switchback

PAGE 11
 >>>

Makeup: When there is a solvent , the vacuum value used by the solvent is shown
in parentheses.

Ink: Detects the status of the ink , the current status is normal , when the ink is
not enough , it will show a shoDž age.

Dot position: refers to the position of the ink dot at the charging pole

Pump rpm: The speed at which the main pump is running.

Viscosity : refers to the viscosity value measured by the current ink.

Mixing Jar: Detects inks that can be used for printing , the current state is normal ,
there will be shoDžages and oveDŽlow.

Phase value: The sensitivity of the phase , the set value in parentheses , followed
by the distance from the second phase detect ion point after the ink dots are
separated.

Mod :Modulation 38 is the set value , and the actual measured value is in
parentheses.

Pressure: The front is the actual measured value , the latter refers to the
temperature of the current nozzle.

Print height: the setting value is in front , and the actual voltage value is in
parentheses.

P_ Mod : the way of printing is selected , a total of four methods , the current is
automatic .

Phase: The position of the phase , and the current position of the phase in
parentheses refers to it.

Gutter: The detection status of ink when it is successfully recyc led , which is
currently normal.

Gutter pump:The speed of the gutter pump during operation.

PAGE 12
 >>>

4.2 Parameter Settings

On the main inteDŽace, press "Conǁ gure" to enter the parameter setting inteDŽace ,
as shown in the ǁ gure:

In order to make it more convenient for customers to use , this inkjet printer divides
the parameters into ǁve options: printing parameter s , counters , time parameters ,
other parameters and special printing.

Each print ǁle has its own unique targeted parameter settings , so eveLj time after
setting the parameters, you must save the parameters , and after pressing " Exit" ,
a dialog box will pop up to let you choose to sav e or not save the parameters.
Parameter modiǁcation, directly click the parameter, the parameter word will turn
red , indicating that the parameter has entered the modiǁable state , and then
directly through the lower numeric keypad to directly enter the value you need ,
and ǁ nally press the "OK" button to lock the input value. Some parameters do not
need to be assigned , such as printing method and printing direction , then click on
the parameter, it will switch a state, press once , switch again , and cycle in turn.

PAGE 13
 >>>

4. 2. 1 Print data

1. print mode
There are four printing methods in total , click on it to switch
'Automatic' : Automatic printing
' Photocell' : External photoelectric sensor controls printing
' Encoder ' : An external synchronous encoder controls the printing
' Ph o+Enc' : An external photoelectric sensor and a synchronous encoder a re
connected to control the printing at t he same time

2. Print direction
There are four modes of printing direction. They are ' normal' , ' inveDžed' , ' reversed' ,
and ' inv+rev' .Click on it to toggle

3. Print speed
Adjust the speed of printing. It is the internal synchronization speed of printing ,
and the printing speed at "0" is the fastest. The printing speed at "10000" is the
slowest.
4. Print height
Adjusts the height of the printed font. The word is the smallest (shoDž) at "0" and
the largest (tall) word at "100" .

5. Print type
The printing type is three modes , which are standard , fast , standard is normal
printing mode , and fast is high-speed printing mode.

6. Print pattern
The printing pattern is based on the printed cont ent , to manually adjust the mode ,
the higher the height of the printed content , the less mode you can select. The
print mode can be modiǁed only if the print type is in express mode , and the print
type is in standard mode , and the print mode is selected as gray and cannot change
the status. The printing mode is modiǁable , there are a total of extreme speed 0 ,
mode 0 , 1 , 2 , double row mode , etc . , extreme speed 0 is the fastest , mode 0 is
slower than extreme speed 0 , and so on.

7. Precision
Adjust the printing accuracy and speed , the larger the value , the better the
printing eƺect , the slower the speed , on the contraLj, the worse the e ƺect , the
faster the speed.

PAGE 14
 >>>

8.Atuo modulation
The modulation search is divided into automatic search and manual search , and
when searching manually, the modulation voltage can be set.

9. Modulation
Set the disconnecting voltage of the ink spot , the larger the value , the higher the
sub-point , the smaller the value , the lower the sub-point , and each inkjet printer
has been debugged when leaving the factoLj. ( It can be changed according to
the actual situation , and it needs to be handled with caution)

1 0 . Print bold
Printing bold is for all the content in the current printing docu ment bold
(horizontal bold) , there are 1 -9 , 1 is not bold , the larger the number, the greater
the e ƺect of bolding.

11. Encoder division

According to the synchronous encoder to print , 1 divide -by- 1 is 1 synchronous
pulse spray a lattice , and 10 divide -by- 10 is 10 pulses spray a dot matrix . The
width of the word can be adjusted.

12. Encoder mulitplier

The value of the encoder divider is multiplied by the value , if the encoder divider
is 5 and the multiple is 2 , then the number of pulses of the encoder divider is 10 .

13. Metering pulse

Metering pulse only works under the encoder (encoder needs to be connected) .
The larger the value set by the meter -by- meter, the greater the number of pulses
required , that is , the longer the distance traveled (the longer the number of meters) .
By adjusting his size , the meter length change (the distance between the ǁ rst and
ǁ rst columns of the two pieces of information content) can be achieved , which is
also known as meter -counting printing.

14. Detection times

The premise of the number of detections is that in the " photocell printing" state ,
it refers to the number of photocell detec tions. In cooperation with the number
of printing, it can play the e ƺect of N times detection and 1 printing.

15. Print times

The number of prints is used in conjunction with the number of detections , and
can be set to detect N prints N times.

PAGE 15
 >>>

16. print delay

Printing delay refers to the time between the ǁ rst content is printed and the
second content is printed

17. Detection delay

This function enables the detection del ay when photocell printing , which is that
the photoelectric eye detects the object , staDžs the time delay, and then prints.

18.Continuous print

Printing of variables for photocell. If the test is played 5 times , the opening is the
same , and the variable content of the 5 prints is the same. The content of the
"diƺerent" printing variable will jump normally each time , and the content will
be diƺerent 5 times.

19. Edit settings

Automatically: that is , after the user sets it , the maximum editing space of a ǁle
is not used , and the useless space is automatically isolated , and the user can
achieve the maximum space utilization. Manual blanking: does not automa tically
use space.

20. Line/Column
Line: Suitable for single -line editing of long messages: the information does not
wrap after pressing the OK key

Column: Suitable for multi- row information editing: After editing the information ,
press the OK key and then move to the next row

PAGE 16
 >>>

4 . 2. 2 Counter

1.Counter 1 current value

The value of Counter 1 refers to the cumulative number of printing since the staDž
of printer, and the principle of Counter 2 and the counter is the same , and it will
not be repeated.

2.Counter 1 upper limit

The setting of this value is limited by the bit value , and the maximum value of the
upper value is the maximum value under that bit va lue. When the counter reaches
the upper limit , it is recounted from the lower limit value 。And the principle of
Counter 2 and the counter is the same , and it will not be repeated.

3.Counter 1 lower limit

The setting of this value is limited by the bit value , and the minimum value of the
lower limit value is the minimum value under that bit value. When the upper limit
is reached by the serial number, the value is recounted from the lower limit value.
And the principle of Counter 2 and the counter is the same , and it will not be
repeated.

PAGE 17
 >>>

4.Counter 1 number of digits

You can change the display to a few digits as needed 。And the principle of
Counter 2 and the counter is the same , and it will not be repeated.
5.Counter 1 increment step

When the value of counter 1 is changed once , the value it increases or decreases
is the size of the step value 。and the principle of Counter 2 and the counter is the
same , and it will not be repeated.
6.Counter 1 cumulative counts
The numeric value typed is reǃ ected on counter 1 and the counter. The number
of times the value of counter 1 changes the set , and the counter is changed only
once.And the principle of Counter 2 and the counter is the same , and it will not
be repeated.

7.Counter 1 increment/decrement
If the value is incremented , it is incremented from the lower value. If decreasing ,
decrement from the upper value.And the principle of Counter 2 and the counter
is the same , and it will not be repeated.

8 . Counter 1 pad 0

There are two types: "yes" and " no" . For example , due to the setting of the number
of digits, it may be eight digits , when "Yes" is selected , the counter 1 staDžs from
the lower limit of the printing "00 000 001 , 0 00 000 02 . . . . " . If you select No, remove
the ǁ rst seven "0" . Only " 1 ,2 ,3. . . . ." .And the principle of Counter 2 and the counter
is the same , and it will not be repeated.

9. Blank unǁleddigits

When the counter 1 is not ǁlled in with zero selection , such as 8 digits is selected ,
and when the user uses only four digits , that is , four digits are empty, the meaning
of the front empty space is that the front space: the four -digit position accounts
for the last four digits of the 8 -digit position ( 1234) , and the back : the four -digit
position accounts for the ǁ rst four digits of the 8 -digit number (1234 ) .And the
principle of Counter 2 and the counter is the same , and it will not be repeated.

10.Counter 1 alarm
AleDžs and stops printing as soon as the Counter 1 reaches a set limit , which can
be turned oƺ or on

11.Warning value
An alarm is issued as soon as the Couter 1 reaches the set value (how much earlier) .

PAGE 18
 >>>

4.2.3Time parameter

1.Year
This parameter is set for the year in the printing date , not the system time. Enter
the time value you need

2. Month
This parameter is set for the year in the printing date , not the system time. Enter
the time value you need

3 . Date
This parameter is set for the year in the printing date , not the system time. Enter
the time value you need

4 . Hour
This parameter is set for the year in the printing date , not the system time. Enter
the time value you need

PAGE 19
 >>>

5. Minute
This parameter is set for the year in the printing date , not the system time. Enter
the time value you need

6 . Second
This parameter is set for the year in the printing date , not the system time. Enter
the time value you need

7.Validity period

The value is set in days , and the current date plus the value of the expiration date
setting is the expiration date required at the time of printing. ( Perpetual calendar
automatic conversion)

8. Maintain
The time remaining until the next maintenance of the machine.

9.Screen time
Enter the screen saver program by staDžing the timer with the las t click on the
touch screen , such as 5 minutes, it is 5 minutes after entering the screen saver.

10.Shift A time
The function of the shift number: you can set the time period to print diƺerent
shift numbers. For example , 0 8 1 1 refers to the time period of 8 : 0 0 - - 11 : 5 9 , and
the printing team number "A" . 0808 refers to the time period of 8:00 - -08:59. Note
that if the time period set by the shift number is c rossed , or if the error occurs , it
will be displayed above , and the shift number time setting is incorrect, please
reset the !!! Moreover, you can't return to the main inteDŽace from the parameter
settings. Must be set correctly to exit.

11.Shift B time
Same shift number A , the same , will not be repeated.

12.Shift C time
Same shift number A , the same , will not be repeated.

PAGE 20
 >>>

13.Viscosity time

The time intedžal of the viscosity test , under normal circumstances , is set at
about 5 minutes.

14. Dilution time

When the actual value measured by the viscosity is greater than the set value , a
diluent is added to reduce the viscosity. The usual set dilution time is 5 sec . This
value has been set, here it is only for display, not operable.

15. ph o valid time

Does the photocell need to open up the ǁltering function of the photocell.

16. Photocell 1 valid time

The time of photocell 1 eƺective time. Within this time , the photocell re -triggering
is invalidated.

17. Photocell 2 valid time

The time of photocell 2 eƺective time. Within this time , the photocell re -triggering
is invalidated.

PAGE 21
 >>>

4.2.4 Other data

1.Auto print

Turn on this function and automatically turn on the " Print Switch" printing after
the ink supply is completed. If this function is not turned on , the printing switch
does not turn on automatically.

2.Gutter detect
When ink is recycled , check if in khas been recycled. When this function is enabled ,
ink is not recycled , and the ink is automatically turned oƺ and stopped. Turn oƺ the
function , no recycling to ink , no processing. Continue printing , the function is to
prevent ink spraying , resulting in ink waste.

3.Gutter threshold
The sensitivity of recoveLj, the smaller the value , the shoDžer and more sensitive
the time to detect the recoveLj failure , the value has basically been set from the
factoLj.

4. RecoveLj rpm
RecoveLj pump speed , the machine aging , the e ƽ ciency of the recoveLj pump
will be reduced , you can improve the value , such as ineƺective can replace the
recoveLj pump.

PAGE 22
 >>>

5.Self- recoveLj

When the printer has a recycling error and stops inking, it will automatically turn
on the ink supply without manual operation. Until the recoveLj has no erro r and
automatically turn on the printing to resume the recent working state. Customers
can choose whether to turn on this function or not.

6.Cover detect
When the printhead cover is detected as open, if the printhead cover is removed ,
the printer will warn that the printhead cover has been removed , and vice versa
without detection.

7.Viscosity&TM

The viscosity will automatically adju st to the appropriate viscosity value according
to the temperature level when it is turned on.

8.Viscosity calibration

Determine a working viscosity value , the higher the value , the higher the viscosity
of the ink , detected viscosity higher than it , it will ǁll the thin , lower than it will
not ǁll.

9. printer pressure

Ink circuit pressure. It is set at the factoLj.

10. Brightness

The brightness of LCD screen , 100 is the maximum brightest , 0 is the minimum ,
the darkest.

11.Charge voltage

Maximum voltage when printing. It is already set up at the factoLj.

12. Phase search

Divided into 1 , 2 , 4 , 8 channels , basically factoLj set.

13. Phase delay

The setting value of the phase delay has been basically set from the factoLj,
so operate carefully.

PAGE 23
 >>>

14. HV detection
Printer in the work due to various accidental reasons caused by HV ǁ re danger
protection function , open this function , will automatically shut down the HV. It
is highly recommended to open this function.

15. HV threshold
Detect the sensitivity of HV ǁ ring , the smaller the value the higher the sensitivity,
the easier to detect HV ǁ ring , and vice versa. The value has basically been set by
the factoLj.

1 6 . Detect memoLj
When the photocell printing under the p hotocell speed is too fast , the printer
detection can not keep up, the function w ill be enabled after the photocell
detection memoLj, will make up the spray.

17. Detection mod

When photocell printing, photocell printing is valid at the rising or fallin g edge
level.

18. Reset
Restore all parameters to their factoLj values and use with caution.

1 9 . Language
For the language of the entire system, you can switch in eveLj languages and take
e ƺ ect after restaDž ing.

PAGE 24
 >>>

4.2. 5 Special

1. Reverse print

This function must be turned on in the case of photoelectric printin g to print

objects coming from the opposite direction.

2. Reverse print direction

For the printing direction set when reverse printing , there are four ways to choose
from the same as ordinaLj printing reverse.

3. Reverse print detect delay

In reverse printing , the photocell detects the object and then delays the time
made before printing.

4. Reverse print reset value

The cumulative number of reverse printing is the same as the c umulative number
of Counter.
5. Reverse print reset number

Number of times after reverse printing , reclassiǁed as normal printing

PAGE 25
 >>>

6. Print area
When turned on , a print ǁle is divided into multiple areas to print, provided that
photocell printing is turned on. Click on it to enter another screen with many
settings for area printing.

7. Mul meter print

The switch used when variable printing is printed together with normal text

8. Meter length print times

If you set 5 , when the variable and the text are printed tog ether, only the variable
is typed the ǁ rst four times , and by the ǁfth printing , the variable and the text
are printed together.

9. Meter counter
The switch used when variable printing is printed together with normal text

10. Intedž al count

Intedžal printing

11.Variable code cycle print

After the variable code is printed , it is normal to stop printing , and after opening ,
it will be printed and then printed in a circular manner from the begin ning.

12. Number of variable code lines

You can set the variable code to print from the ǁ rst few lines of the ǁle

PAGE 26
>>>

4. 3 Message
On the main inteDŽ ace , click the “ Message” inteDŽace , as shown in the ǁ gure:

On the left is the ǁle page, in the middle is the printed content of the document , and
lattice height of the ǁle. As shown in the picture , the ǁ rst ǁle is named 57o.xml ,on
its right side is the height of print ǁle ,and it ’s 25 .Under the ǁle name is the printed
content. This inteDŽace can only store 6 printed ǁles , through “ ↑↓” button to view
other documents , the content of the printed ǁle is blue , the selected ǁle content will
become red , the other is black.

4.3. 1 New ǁle

Create a new printing ǁle , click " New ǁle" , a dialog box will pop up, enter the ǁle name
you need , and click "OK" after entering. The newly created ǁles are ranked last , the
order of the ǁles is arranged according to the time the ǁle was creat ed , the newest is
ǁ rst , and the next ǁle is soDžed down, deleting one ǁle and the next ǁle on top.

If you click " Exit" , the new ǁle will not be created , and you will return to the printing
document management inteDŽace.

4. 3. 2 Editing
Click " Edit" to enter the relevant inteDŽace , as shown in the ǁ gure:

PAGE 27
 >>>

4. 3. 2 Editing
Click " Edit" to enter the relevant inteDŽace , as shown in the ǁ gure:

After entering the content in the editing box , there will be a corresponding red dot
matrix content display in the actual operation area , and the orientation of the dot
matrix is based on the right top X=0 , Y=0 coordinates. You can use the four arrow
keys to set the orientation in advance , and after entering the content , click the
“ Enter ” button to ǁx the content , and the dot matrix changes from red to black. If
the dot matrix is still red and exits , the red paDž of the content input is invalid.

All lattice parameters can only be set when the dot mat rix is still red , and can no
longer be set when the content is ǁxed , and continue to enter after entering a ǁeld.
When editing the orientation , the dot matrix must also be red , up and down
movement can be set independently, in the left and right movement should pay
attention to the cursor in the edit box jump to the ǁ rst character before the dot
matrix can move left , otherwise it is to move left on the content in the edit box .
Right-shifting is also the case where the cursor must jump to the last character of
the content before it can be moved right , otherwise it is moving right on the
content in the edit box .

PAGE 28
 >>>

4.3.2.1 English
English : When typing, you can set the font in advance , or you can set the font after
entering and click the button “ EN **”
There will be a drop-down menu for you to choose from , and the English fonts are:

5×5 4×7 5×7v 5×7d 5×7h 5×7i 5×7l 5×7w 7×9

7×9v 7×10 8×12 8×16 8×16c 12×1 6 12×2 4 32×32

4 . 3 . 2 . 2 Chinese characters
Chinese characters: Click the button “CN **” and a drop-down menu will come out
for you to choose from , and the fonts Chinese input are:

8×8 10×1 0 12×1 2 16×1 6 16×16c 20×20 24×24

It should be noted that when entering the pinyin input method , some symbols are
Chinese symbols entered , and if you need English symbols , you must ǁrst switch
back. Under the pinyin input method , after entering pinyin , a font has many words
to choose from , 9 words per page , and you can select the '<>' button issued after
the font bar to select words. The input method is an intelligent input method ,
which can be continuously spelled , such as production , and can be directly input
to SC to select.

4. 3. 2. 3 Move left
Left shift: the actual operation are a size is height 35 , width 230, press the left arrow
button, is to move 60 units to the left , this left shift is the entire operation area left
shift , and the arrow key left , just the current dot matrix to the l eft.

4. 3. 2. 4 Move right
Right shift: the size of the actual operation area is height 35 , width 230, press the
right arrow button once, is to move 60 units to the right , this right shift is the entire
operation area to move right , and the arrow key right , just the current dot matrix
to move to the right.

4 . 3. 2. 5 Field Selection
Field selection: If you have a ceDžain ǁ eld edit or want to change the ǁ eld, you can
use " Field Selection" . Press once to select one ǁeld , and press again to select the
next ǁeld. When the ǁ eld is selected , the content (text or icon) in the entire ǁeld
will be displayed in red , and the order of selection is the order in which the input is
determined.

PAGE 29
 >>>

4.3.2.6 Field determination

Field determination: In the editing box , after the character is entered , if you want
to enter the next character, you must press the " Enter " on the keyboard to ǁx a ǁ eld ,
so that the dot matrix character changes from red to black , indicating that the
character has been determined and solidiǁed.

4 . 3 . 2 . 7 Field Deletion
Field deletion: After entering for a piece of content, if you want to delete the entire
ǁ eld , click ' Field Selection' , if there are multiple ǁ e lds , click a few more times , it will
be selected in each ǁ eld , after selecting the ǁ eld , the content of the entire ǁeld
turns red , and then click , so that the entire ǁeld will be deleted.

4. 3. 2. 8 Normal
Normal : The default font direction is ' normal' , press " Direction:normal" , the next
drop-down menu will come out, you can directly choos e between ' normal' ,
' Reverse' , ' InveDžed' and ' Reverse+InveDžed' . This is for all the characters in a ǁ eld ,
if you need a single character, you need to staDž a new ǁeld and se t it for a single
character.

4.3.2.9 Bold
Bold: Click " Bold: 1" , a drop-down menu will come out , the ǁ elddefaults to the
thickness of the original font 1 . The minimum is 1 and the maximum is 8 . This is for
all the characters in a ǁ eld, if you need a single character, you need to staDž a new
ǁ eld and set it for a single character.

4.3.2.10 Spacing
Spacing: Click "Spacing: 0" and a drop-down menu will come out. The minimum
value is 1 , the maximum value is 8 , and the order is increasing. You can select the
size of the spacing from the down menu. This is for all the characters in a ǁ eld , if
you need a single character, you need to staDž a ne w ǁeld and set it for a single
character.

4. 3. 2. 1 1 Clear Editing
Empty: If you enter many ǁe lds , but ǁnd that there is a problem , and the ǁ elds are
deleted too slowly, you can use “Clear Editing ” , which will erase all the content in
all the actual operation areas.

PAGE 30
 >>>

4.3.2.12 Variable inputs

Click ” Variable ”on the keyboard , a variable keyboard will pop up, enter on demand ,
and the font can also be selected in advance. Year, month , day, hour, minute , and
second are set in the parameter settings (not the cu rrent correct date) , sequence
1 is the input of the current value of serial number 1 , and sequence 2 is serial
number 2. If the team number is no longer set within the time period , it is
represented by a space , such as in the time period , it is one of the three parameters
of A , B , and C. The e ƺective year, e ƺective month , and e ƺective date are the number
of days set in the validity period in the parameter settings plus the time after the
year, month and day. You can also type variable text, barcode and QR code , area
printing , etc .

4. 3. 2. 13 Logo Input
Press “Logo input ” to enter the inteDŽace , as shown in the ǁ gure:

There are two sources of graphics: local ( native) and USB stick graphics

Local ǁle: It is a self- made graphic on the printer, displayed in the upper blank area ,
and then selected by the arrow keys or Tab keys to conǁ rm, press Select to open.
USB ǁle:It is a graphic stored on the U disk anddisplayed in the upper blank area ,
and then select OK by the arrow keys or Tab keys, press Select to open.
Delete: Deletes the drawing ǁle
To USB; Copy the graphics ǁles from the printer to the USB ǃash drive.

PAGE 31
 >>>

If you do not need to input a bitmap, press to exit and return to the normal input
inteDŽace.

4 . 3 . 2 . 1 4 Variable code
Click “ Variable code ”， inter the “ Variable code ” inteDŽace， as the ǃ ow ǁgure：

The format of the data source must be a document with the s uƽx .txt , and the
number of bits in each row of data must be the same , if diƺerent , it must be based
on the number of digits with the largest number of digits , and the insuƽ cient
number of digits must be completed by spaces. The variable code ǁle can be stored
in the U disk , so when reading the variable code , please press the “ USB data ” to
read the variable code from the U disk. Press the “Online data ” , obtain the variable
code according to the data transmitted from the PC , and contact the manufacturer
for relevant technical documents. The read variable code data information is
displayed in the blank space and selected by the arrow k eys. The choice of the font
of the variable code can be set in advance, if there is no need for variable code input ,
press Exit to return to the normal input inteDŽace.

The variable code parameter can be selected by yourself, press the font " En 4x7" to
select the variable code font of text input, press " 1 line" to select the number of lines ,
click the button in turn The number of lines will be cycled through 1~ 5 lines. Variable
code data can be conveDžed , such as text, barcode , QR code and so on. When
conveDžing to barcodes, you can press " Height 16 , visible text" to select the height
of the barcode and whether to display characters.

PAGE 32
 >>>

4.3.2.15 Barcodes
Click " Barcode" to enter the barcode input inteDŽace , as shown in the ǁ gure:

The default is 128 barcode input , click the " Barcode type: 128" button to switch the
required barcode type. All barcode mechanisms are EAN13 , EAN8 , UPA-C , UPA-E ,
ISBN , CODE39 , CODE93INTER 2/6 , CODABAR . After determining the barcode format ,
click the " Height 16 , visible text" button to select the height of the barcode and
whether to display characters.

In the editing box on the left according to the barcode c oding rules to enter the
barcode data you need , click " Preview" , the barcode will be displayed on the right ,
after determining the barcode content , click "OK" to exit and return to the normal
input inteDŽace, if there is no need to enter, click " Exit" to return to the ordinaLj
input inteDŽace.

PAGE 33
 >>>

4.3.2.16 QR code
Click "QR Code" after entering the QR code input inteDŽace , as shown in the ǁ gure:

In the edit box on the left , enter the required characters according to the rules , click
" Preview" , there will be a QR code display eƺect in the preview area , click "OK" , and
return to the main inteDŽace of input , no need to enter this press Esc to exit to return
to the main inteDŽace of input.

At the time of input , the “Size ” , “ Mode ” , “ InveDžed ” and “QR level ” can be set for the
attributes of the QR code and the barcode mechanism. Click the buttons for your
desired parameters in turn to cycle through the selection.

PAGE 34
 >>>

4.3.2.17 InseDžion and Replace

When editing , sometimes the editing will be missed or wrong , this time you can use
the keyboard This option is only available in the editing ǁle , and when the ǁ eld is still
red , you can use the four directional keys or move the right key to select a position ,
the color of the cursor is blue , and the left side of the cursor position is the position
where the content is inseDžed. When you click the " InseDž" button again , the content
of the button will become " Replace" and the word " Replace" will change to red , the
color of the cursor is black , when entering , the character at the position of the
cursor will become the character you need , that is , replace the original content.

4.3. 2.18 Save the ǁle

After editing the printing content , click the " Exit" button directly, and a selection
window will pop up with a prompt bar: " Do you want to save the ǁle or save the ǁle?!" ” 。
The pop- up window has 4 buttons , namely: Save , Save as , Cancel , Exit. Click to
select , and operate.

4.3.3 Printed documents

In the printing ǁle management inteDŽace , after selecting the ǁle , click it ” Print ” to
open the ǁle and print the ǁle , returning to the main inteDŽace.

4.3.4 ImpoDž and ExpoDž

In the printing ǁle management inteDŽace, you can choose to manage the ǁle , ǁ rst
select a ǁle ready to be expoDžed , and then click " ExpoDž " , an inteDŽace will pop up,
after naming the expoDžed ǁle , click "OK" . (The default of the printer is to expoDž the
ǁle to the USB ǃash drive , so please make sure that the USB ǃash drive has been
inseDžed into the inkjet printer in advance) so that the ǁle will be saved to the USB
ǃ ash drive. If you encounter a ǁle with the same name, you will be prompted to
rename the ǁle , otherwise the operation cannot be completed.

" ImpoDž " , click the same way to impoDž the ǁle from the U disk to the inkjet printer,
so no other operations are required , just make sure that the U disk has been inseDžed
into the inkjet printer and make sure that there is an impoDž ǁle in it. Select the ǁle
to be impoDž ed , and then click the " ImpoDž " button to impoDž the ǁ le into the printer,
if you encounter a duplicate ǁle , you will be prompted to rename t he ǁle , otherwise
the operation cannot be completed.

4.3. 5 Delete
In the ǁle management inteDŽace, for the ǁles that are not used , you can implement
the deletion of the ǁle , after selecting the ǁle , press “delete ” , a warning dialog box
will pop up, there is a prompt content "OK to delete this ǁle (folder)" , press OK ,
delete the ǁle and return to the printing ǁle mana gement inteDŽace , do not delete
press Cancel , return to the printing ǁle management inteDŽace.

PAGE 35
 >>>

4.3.6 Search
When printing too many ǁles, page by page search , the speed is relatively slow, you
can pass , click the button , the soft keyboard will pop up and prompt for the ǁle name ,
after entering the ǁle name , click conǁ rm will ǁnd the ǁle , and select on.

4.3.7 Exit ( Esc)

In the printing ǁle management inteDŽace, if you do not need to do anything ,
directly press the lower right corner to exit and return to the main inteDŽace.

4.4 Ink operation

4.4. 1Ink operation
Press the “ Ink operation ” on the main inteDŽ ace to enter the inteDŽ ace , as shown in
the ǁ gure:

Enter the “ ink operation inteDŽace ” , the default is the “ ink operation ” , will prompt
the current state of the printer, such as the above chaDž prompt: the working state.
Note: Some operations can only be operated in ceDžain states , and the options that
cannot be operated will be presented in gray font , and the operation is invalid in
gray state.

PAGE 36
 >>>

1. Click "StaDž up jet" :

After this function is executed , the nozzle will have ink lines ejected (if the 'Auto
print' function is turned on) , the system will automatically staDž working , and the
counter and serial number will be turned on to count.

2. Click "Shutdown jet" :

This function is used for stopping the machine for less than 2 hours , after the
execution , the nozzle in kline will stop, and the counter and serial number w ill stop
counting.

3. Click "Clean stop" :

This function is used for stopping more than 2 hours. But do not exceed 3 times a
day times a day. After the execution , the nozzle in kline stops , and automatically
and thoroughly clean the nozzle , recoveLj tube and other ink circuit components.

4. Hit " Fill mixing resedžoir " :

The ǁ rst time you turn on the printer, the in k caDž ridge inseDž ed into the caDž ridge
tank , makeup caDžridge inseDžed into the makeup tank , the ink and makeup need to
be directed to the ink core this process is long, you need to wait patiently.

5. Viscosity :
Test the viscosity of the ink in the mixing cylinder, will be a ƺected by factors such
as temperature , the test takes a ceDžain amount of time.

6. Click "Clean reverse" :

The implementation of this function so that the spray cavity in a vacuum, you can
inject the cleaning agent from the nozzle end to clean the nozzle . When the in kline
can not be correctly into the recoveLj tube.

7. Click " Forward purging" :

This function al one with makeup cleaning nozzles.

8. Click "Clean and air exhaust" :

This function is to clean the ink circuit and exhaust the air inside.

9. Click " PoweDŽul cleaning" :

If the printer with " reverse cleaning" and "forward cleaning" , " nozzle throat
cleaning "After, still can not be normal ink supply, you can use this function , but
will consume a lot of thinner.

10. Click " long down time for cleaning" :

Jet printer does not work for a long time, you need to use this function to clean the
ink circuit to prevent the ink from dLj ing out, blocking the ink circuit.

PAGE 37
 >>>

11.Click “ Ink core discharge ink ” :

This function , which will cause all the ink in the ink core to be excluded , operates
according to the prompts in the inteDŽace.

12.Click “Clean recycling pump” :

Recycling pump because of a long period of time without work , the ink inside dried
up or sticky, resulting in recycling pump eƽ ciency or speed is not up to standard ,
you can use this function

After the “StaDž up ink ” process is complete, ink operation inteDŽace will prompt: the
printer is running , and “StaDž up jet”and “Clean reverse”are gray, inoperable state.

In the ink operation inteDŽace , click "Valve" to enter the solenoid valve test inteDŽace ,
in the ink supply running state is not accessible , if you click "Valve" , there will be a
prompt window: "When ink pressure is on , solenoid valve can not be operated!!!" .

After the solenoid valve test inteDŽace, you can click " Ink Operation" to return to the
ink road operation inteDŽ ace , the two inteDŽ aces can be switched back and foDž h.

4.4.2 Solenoid valve testing

Press “Valve ” to enter the inteDŽace , as shown in the ǁ gure:

PAGE 38
 >>>

4. 5 System

When you enter this screen , the default is to enter the About this machine screen
as shown above.

This inteDŽ ace has 8 option screens

4. 5. 1 About : The About the printer screen has three sub sidiaLj screens , Printer
Info, System Time , and Calibration.

4.5.1.1Printer info
Printer info can be seen on the Printer ’s software version , the total capacity, the
upgrade version , the remaining capacity, the check code , the Printer SN , the ink
and makeup in its bin is how much standard volume , the printer has been running
for the time.

PAGE 39
 >>>

4.5.1.2 system time

After the RTC batteLj is depleted , the batteLj needs to be reloaded and the
system time needs to be reset.

PAGE 40
 >>>

4 . 5 . 1 . 3 Calibration

This inteDŽace has three calibrations

1. Time calibration: user login password is required to calibrate the time

2. High voltage calibration: The printer just arrived at an environment needs to

adjust the state of high voltage according to the environment. Need to be
calibrated.

3. Touch screen calibration: the touch screen is damaged , after a new one , it needs
to be calibrated to get an accurate positioning of the touch screen.

PAGE 41
 >>>

4. 5. 1. 4 Viscosity

“Set viscosity” is standard value of viscosity for the printer itself.

“Scale data ” is for each viscometer 's own variability, aDžiǁci ally correct a ceDžain
percentage of the oƺset value.

PAGE 42
 >>>

4. 5.2 System Log

This screen is for the system log and update log. The system log allows you to
view the machine's operating status , when it was turned on and oƺ, and other
information. The update log allows you to see when the printer was updated wi th
the program.

PAGE 43
 >>>

4 . 5 . 3 Self- test
4.5.3.1 SYS status
Self-test inteDŽace has three sub sidiaLj inteDŽaces, divided into system status ,
self-test and printhead reset. The ǁ rst inteDŽace into the inteDŽace is the system
status , the inteDŽace can view the working status of the machine's hardware and
parameters.

PAGE 44
 >>>

4 . 5 . 3 . 2 Self- test
After entering the inteDŽace , click on the “Self-test ” , it will monitor all the electronic
components inside the printer and self -test, you can get the temperature , current ,
voltage , speed and other parameters, you can get a detailed understanding of the
state of the printer 's hardware.

PAGE 45
 >>>

4 . 5 . 3 . 3 Printhead
For machine maintenance and change of venue after the printhead environmental
variability and hardware variability changes , the need to ǁnd the right parameters
again , the need to reset the printhead to the standard value of the work.

PAGE 46
 >>>

4. 5. 4 Active chip

After the consumables are consumed , new consumables are needed. After the new
consumables are inseDžed into the printer, they need to be activat ed and a 20 -digit
activation code has to be entered before the consumables can be used by the
machine , and the activation code needs to be licensed by our software algorit hm.

4. 5. 5 Upgrade
In the case of no user password login can only operate these four inteDŽaces , through
more functions , enter the user login inteDŽace , enter a correct user name and
password , you can enter the " Upgrade" , " Remote" , " Users" , "Customize" inteDŽace ,
enter the " Upgrade" inteDŽ ace, it has three sub sidiaLj inteDŽaces , for " Network" , "WIFI" ,
" Upgrade" three inteDŽaces.

PAGE 47
 >>>

4 . 5 . 5 . 1 Network
After entering the inteDŽace , the initial is the " Network" inteDŽace under normal
circumstances , click on the automatic acquisition will be able to wired network
available information , exit the inteDŽace can be directly into the system upgrade.

PAGE 48
 >>>

4.5.5.2 WIFI
In the absence of a wired network , you can also use a WIFI to upgrade , select a
hotspot in the inteDŽace , then a dialog box will pop up, prompting for a password ,
enter the correct password , in the column of the connection , a "tick" will be
displayed , and then you can upgrade the system. In the case of popular sm aDžphones ,
you can also open a cell phone hotspot to act as a WIFI , the operation is the same
as the ordinaLj WIFI connection, but you need to remember the name of the phone
and the hotspot password.

PAGE 49
 >>>

4. 5. 5. 3 Upgrade
After the wired network or WIFI has successfully acquired a network connection

Enter the ” upgrade ” inteDŽace , under normal circumstances is to use the exter nal
network upgrade , and then click " Next step" , in this state , only check the upgrade
when black , such as network problems , will prompt to check the network status ,
such as no problem will appear upgrade package

After selecting the upgrade package , " Download" will change from gray to black ,
and then click " Next step" .After the progress bar above , the download is complete ,
“Check ǁle ” will change from gray to black , indicating that you can proceed , click
" Next step" , after check the ǁle integrity is OK , update the system will change from
gray to black , you can proceed to the next step " Update system" , after the update
is complete , the system will automatically reboot.

PAGE 50
 >>>

4. 5.6 Remote

Remote display is through a speciǁc software , on the PC , the printer remote display,
you can project the printer inteDŽace to the PC , using the PC to control the printer.
This function can be set to "Self-staDžing" , "WAN mode" ."Self-staDžing"selected ,
eveLj time automatically will automatically open the remote display f unction , not
selected , is white , need to manually staDž to change the function. "WAN mode" , after
the green button is selected , is that you can use the WAN oƺ-site operation of the
machine , not selected , is the LAN mode , the need for the software, you need to
contact with the company and obtain.

PAGE 51
 >>>

4. 5.7 Users
The inteDŽace has two sub sidiaLj screens with prompts to "Add a user " and " Password"
according to your needs , and when you peDŽorm these two operations, you will be
prompted on how to do so.

4. 5.8 Customize
Each user has diƺerent functional requirements , so there is a need for customization.
In total , there are 5 customization screens as shown in the ǁ gure.

PAGE 52
 >>>

Go customize, parameters , alarms, fonts , and modify fonts according to customer

needs.

4.6 Logo editing

In the main inteDŽace , click " Logo editing" to enter the graphics editor inteDŽace ,
where you can edit local icon ǁles , or impoDž ǁles from the USB ǃash drive and edit
them , as shown in Figure.

4. 6. 1 Logo editing

PAGE 53
 >>>

When you enter this inteDŽace, you can see that the inteDŽace has put the height and
width in a scale clearly marked up. You can move the red pixels with the arrow keys ,
and the red dots will appear in the grid , which means you are already in the area.
When you click on the "Set" button , the red dots will become small black dots and
the dot matrix will be drawn , click on the "Set" button again at the corresponding
black dot position and the small black dot matrix will be cleared. If you need to edit
a straight line, you can click " Dot" to switch to "Line" , so that you can use the arrow
keys to draw a continuous point "straight line" . If you are not satis ǁ ed with the edited
content, you can click on "Clear " to clear the drawing.

Below is the actual pixel display of the graph. The width and height settings can be
increased or decreased by "+" or " -" . The height has a limit , if the input value exceeds
the maximum value, it will be input with the maximum value , the blue box is the
maximum height and width of the icon ǁle , editing must be inside the blue box ,
beyond the invalid. After drawing , click New, that is , save the graphics ǁle , enter
the ǁle name.

4.6.2 ImpoDž
In "ImpoDž ", you can impoDž two kinds , “ Local ǁle ” and “ USB ǁle ” , as shown in the
ǁ gure.

PAGE 54
 >>>

Click " Local ǁle" , blank out only the local graphics ǁle , other locations of the graphics
ǁle is not displayed , such as local graphics does not show anything, indicating th at
there is no local ǁle , or the ǁle format and content does not match t he device. Then
click Select ǁle , and click Select to open the ǁle and enter the graphic editing
inteDŽace to edit the icon ǁle after determining the ǁle. Click on " USB ǁle" , the same
result will appear, and the same way to handle. " Delete" that is , to delete the selected
graphics ǁle , "To USB" that is , the local graphics copy to the U disk , provided that
the U disk has been inseDžed into the printer. If you do not need to operate , click
" Exit" to return to the logo editing inteDŽace

4.6.3 Extract font

Customers have special requirements for some characters , click " Extract font" , you
can modify the characters , enter the word pattern extraction inteDŽace , as shown in
the ǁ gure.

In the edit box of the extract font dialog box , enter the font you want to modify ǁ rst.
You can ǁrst select a font , English fonts and Chinese characters can be entered ,
font switching is also clear in the previous ǁle editor, no longer repeat , after input ,
click "conǁ rm" , the characters in the form of dot matrix extracted into the graphics
editor, you can edit , click "exit " Do not extract any character pattern , return to the
graphics editor inteDŽace.

PAGE 55
 >>>

4.6 System log

4.6. 1 Print Record
Enter the “System Log ” and see the two screens attached to it , “ Print records ”and
“ Random Code View ” .

In the “ Print records ” inteDŽace, you can view the message you have printed , you
can view the ǁle name print staDž time and end time , the number of prints , serial
number staDž value and serial number end value. And you can turn the page to
view the printing at a glance.

PAGE 56
 >>>

4. 6. 1 Random Code View

This screen allows you to see what random codes have been printed and to which
line the random codes have been printed. You can ǃip up and down the page , and
view the printed page.

PAGE 57
 >>>

Annex 1:Use of soft keyboards

The use of soft keyboards makes the information content more dir ect. Speciǁcally
introduce the function of each button , the ǁ rst row is the number key, the case
conversion key, will conveDž all lowercase letters (a -z) to uppercase subtitles (A-Z) ,
common symbol toggle keys. Like what! @ # $ % ^ & * ( ) _ + = ’ [ ] / ; . , : , have multiple
pages to select , click again on the pop- up other symbols ~ { } | ? < >。

If you want to edit the content of multiple rows , edit the ǁ rst row, you can directly
press to directly edit the content of the next row. Whenever a piece of content is
entered , whether it is text , icon , random code or barcode , its content is still red , and
it must be clicked to solidify the content to complete the real input of the content.

PAGE 58
>>>

Marcespe 睦睢睝 线路板连接图

机 箱 照明 灯

转接板
交流输⼊
墨路板
主板

PAGE 59
喷头
综合阀
回收泵
真 空 传感 器 压⼒ 传感 器
添加泵
综合泵
主泵 启动开关和待机指⽰灯
清洗泵
分线板
墨芯板
附件2 线路板连接图

外设版
⾼压盒
⻛扇
正压⻛电机
墨⽔座板 溶剂座板
2022 - 11 - 02 11:48 Please peDŽorm HV calibration

Conǁ guration Message Operation System Logo edi ting Print log

Printing info: MCP E-220 Edit current ǁle

Counter 001670009 Reset

Counter1 001670009 Reset

Dot position:0 Pu mp rp m 0000 Viscosity: 0 . 0 ( 3 0 . 0 ) Mixing Jar:shoDžage

Phase value:0 Mod :45( 0 . 0) Pressure:0 . 000( 0 . 0℃) Print Height:100( 6120) More

SN: 2 C 4 2 4 5 3 1 0 3 0 0 0 0 C E
ABC

Beijing Marcespe Machinery

Equipment Co. , LTD
Print Clean Clean Power
Ink Make up
oƺ staDž stop oƺ
50%(0 . 00) 45%(0 . 00)