ECU List –

GEMS
Gen-set controller for Gas
application

SW version 2.3.0
Table of contents 2
1 Document information 3
2 Principle of ECU support 5
3 List of ECU 9
4 Notes 43

Copyright © 2022 ComAp a.s.

Written by Martin Kaňok
Prague, Czech Republic
ComAp a.s., U Uranie 1612/14a,
170 00 Prague 7, Czech Republic
Tel: +420 246 012 111
E-mail: [email protected], www.comap-control.com Global Guide
Table of contents
1 Document information 3
1.1 Clarification of Notation 3
1.2 About this guide 3
1.3 Legal notice 3
1.4 Document history 4

2 Principle of ECU support 5

2.1 What must be done to support a new ECU? 5
2.2 What data can be transmitted to / from ECU? 6
2.3 What is an ESL file? 6
2.4 What is the default ESL setting? 7
2.5 How to import ESC - ESL package? 7
2.6 SAE - J1939 diagnostic connector 7
2.7 How to create a constant for ECU control 8

3 List of ECU 9
3.1 Altronic CD200XX and NGI1000 10
3.2 Altronic NGI 1000RC 12
3.3 GMF 14
3.4 Heinzmann Ariadne 16
3.5 Heinzmann Helenos 18
3.6 Heinzmann Kronos 19
3.7 Heinzmann Pandaros 20
3.8 Heinzmann Phlox 21
3.9 MWM ADEM A4 24
3.10 Powerlink 26
3.11 TPEM 27
3.12 Trijekt 33
3.13 Uninox 39
3.14 Varistep 1 41
3.15 Varistep 2 42

4 Notes 43
4.1 Software compatibility 43

ECU List – GEMS 2.3.0 Global Guide 2

1 Document information
1.1 Clarification of Notation
Note: This type of paragraph calls the reader’s attention to a notice or related theme.

IMPORTANT: This type of paragraph highlights a procedure, adjustment etc., which can cause a
damage or improper function of the equipment if not performed correctly and may not be clear at
first sight.

WARNING: This type of paragraph highlights a procedure, adjustment etc., which can cause a
damage or improper function of the equipment if not performed correctly and may not be clear at
first sight.

Example: This type of paragraph contains information that is used to illustrate how a specific function
works.

1.2 About this guide

ECU list GEMS is used as standard ECU list for controller IS2GAS.

1.3 Legal notice

This End User's Guide/Manual as part of the Documentation is an inseparable part of ComAp’s Product
and may be used exclusively according to the conditions defined in the “END USER or Distributor LICENSE
AGREEMENT CONDITIONS – COMAP CONTROL SYSTEMS SOFTWARE” (License Agreement) and/or in
the “ComAp a.s. Global terms and conditions for sale of Products and provision of Services” (Terms) and/or in
the “Standardní podmínky projektů komplexního řešení ke smlouvě o dílo, Standard Conditions for Supply of
Complete Solutions” (Conditions) as applicable.
ComAp’s License Agreement is governed by the Czech Civil Code 89/2012 Col., by the Authorship Act
121/2000 Col., by international treaties and by other relevant legal documents regulating protection of the
intellectual properties (TRIPS).
The End User and/or ComAp’s Distributor shall only be permitted to use this End User's Guide/Manual with
ComAp Control System Registered Products. The Documentation is not intended and applicable for any
other purpose.
Official version of the ComAp’s End User's Guide/Manual is the version published in English. ComAp
reserves the right to update this End User's Guide/Manual at any time. ComAp does not assume any
responsibility for its use outside of the scope of the Terms or the Conditions and the License Agreement.
Licensed End User is entitled to make only necessary number of copies of the End User's Guide/Manual. Any
translation of this End User's Guide/Manual without the prior written consent of ComAp is expressly
prohibited!
Even if the prior written consent from ComAp is acquired, ComAp does not take any responsibility for the
content, trustworthiness and quality of any such translation. ComAp will deem a translation equal to this End
User's Guide/Manual only if it agrees to verify such translation. The terms and conditions of such verification
must be agreed in the written form and in advance.
For more details relating to the Ownership, Extent of Permitted Reproductions Term of Use of the
Documentation and to the Confidentiality rules please review and comply with the ComAp’s License
Agreement, Terms and Conditions available on www.comap-control.com.

ECU List – GEMS 2.3.0 Global Guide 3

 Security Risk Disclaimer
Pay attention to the following recommendations and measures to increase the level of security of ComAp
products and services.
Please note that possible cyber-attacks cannot be fully avoided by the below mentioned recommendations
and set of measures already performed by ComAp, but by following them the cyber-attacks can be
considerably reduced and thereby to reduce the risk of damage. ComAp does not take any responsibility for
the actions of persons responsible for cyber-attacks, nor for any damage caused by the cyber-attack.
However, ComAp is prepared to provide technical support to resolve problems arising from such actions,
including but not limited to restoring settings prior to the cyber-attacks, backing up data, recommending other
preventive measures against any further attacks.
Warning: Some forms of technical support may be provided against payment. There is no legal or factual
entitlement for technical services provided in connection to resolving problems arising from cyber-attack or
other unauthorized accesses to ComAp's Products or Services.
General security recommendations and set of measures
1. Production mode
Disable production mode BEFORE the controller is put into regular operation.
2. User accounts
Change password for the existing default administrator account or replace that account with a
completely new one BEFORE the controller is put into regular operation mode.
Do not leave PC tools (e.g. InteliConfig) unattended while a user, especially administrator, is logged in.
3. AirGate Key
Change the AirGate Key BEFORE the device is connected to the network.
Use a secure AirGate Key – preferably a random string of 8 characters containing lowercase,
uppercase letters and digits.
Use a different AirGate Key for each device.
4. MODBUS/TCP
The MODBUS/TCP protocol (port TCP/502) is an instrumentation protocol designed to exchange data
between locally connected devices like sensors, I/O modules, controllers etc. By it's nature it does not
contain any kind of security – neither encryption nor authentication. Thus it is intended to be used only
in closed private network infrastructures.
Avoid using MODBUS/TCP in unprotected networks (e.g. Internet).
5. SNMP
The SNMP protocol (port UDP/161) version 1 and version 2 are not encrypted. They are intended to be
used only in closed private network infrastructures.
Avoid using SNMP v1 and v2 in unprotected networks (e.g. Internet).

1.4 Document history

Revision number Related sw version Date Author
1 2.3.0 10.6.2022 Martin Kaňok

ECU List – GEMS 2.3.0 Global Guide 4

2 Principle of ECU support
Since the engines with electronic fuel injection became commonly used, ComAp has introduced a convenient
solution for monitoring and management of such engines based on existing controllers InteliLite and
InteliGen. These used to be fixed programmed and dedicated to a specific engine type, ECU or
communication protocol. A separate module – I-CB (Communication Bridge) – was designed to interface
InteliSys controller and ECU unique for its hardware or software features (e.g. communication speed).
Due to great development on the side of the engine manufacturers regarding electronic equipment and
amount of transmitted data from the ECU/engine, ComAp had to react promptly and launched new system of
ECU support in the controllers. This new approach described below was started by the InteliDrive DCU
controller. Later on it was adopted by the InteliLite controller (since version 2.0) and nowadays is integrated
into all ComAp controllers.
The new way of ECU support provides above all an easy and fast way how to integrate a new type of ECU.
Although the engine manufacturers often declare that the unit provides standard J1939 communication, after
deeper analysis many of them appear to use proprietary data frames. Therefore ComAp controllers are
simply reconfigurable for such specific units using an external file – Engine Specific Code (ESC) – which
contains all necessary information about transmitted values, commands and diagnostic messages. The
contents of this file are downloaded to the controller which can afterwards provide complete data monitoring
and engine control over the CAN bus.
The above described procedure of implementation of an ECU support ensures easy to use and fast
configuration however it doesn’t reduce the controller’s flexibility. The user should be aware that ComAp
provides default configuration and the controller must be adapted and configured to particular application.
Providing the most common adjustment doesn’t eliminate the need to thoroughly test the functionality of the
installed controller in conjunction with the gen-set and other equipment and advice the end user about the
way of its operation.
Due to quick development in this area it is strongly recommended to check up ComAp web pages
(www.comap-control.com) for software and documentation updates ahead of carrying on with projects
comprising electronic engines.

2.1 What must be done to support a new ECU?

Let's say about units communicating over CAN bus and using J1939 protocol (we will leave out specific units -
using RS232/RS485 or their own CAN bus lines, Modbus). As mentioned above we cannot rely on ECU brief
specification which states that the unit supports J1939 protocol but we have to study a comprehensive
specification describing all details of data communicated by the unit. Only then it is possible to create an ESC
and test it with the engine. So the necessary steps are in brief:

ECU List – GEMS 2.3.0 Global Guide 5

 Study ECU documentation
If the ECU is fully compatible with SAE J1939-71, an ESC for “Standard J1939 engine” can be used
If the ECU is sufficiently but not fully consistent with SAE J1939-71, a new ESC has be created in ComAp
The controller with new ESC has to be tested with the engine/ECU (without testing the functionality is only
theoretical – operating conditions of ECUs can vary a lot (for example sequence of activating/deactivating
of ECU inputs during starting/stopping of the engine))

2.2 What data can be transmitted to / from ECU?

There are generally four types of data communicated between the controller and ECU:
Values read from the ECU (e.g. Engine coolant temperature, Lube oil pressure)
Values/parameters written to ECU (e.g. Speed control, Frequency select)
Commands written to ECU (e.g. Start/Stop, Fault reset)
Fault codes

2.3 What is an ESL file?

ESL (ECU Specification List) file contains list of all supported ECUs for a given controller. The particular list
appears in LiteEdit, LiteEdit 2015, DriveConfig, GenConfig, NanoEdit, ECUDiag as a list of available
engine/ECU types. The ESL file also defines communication/diagnostic protocol used in the ECU.

ECU List – GEMS 2.3.0 Global Guide 6

2.4 What is the default ESL setting?
ComAp offers many kinds of controllers for various applications. Almost each of our controllers supports
electronic engines, but the configuration PC software and its settings are different. Therefore we have various
ECU lists designed for each controller's family. ECU list GEMS is designed for IS2GAS, ISGSC, ID-DCU
controllers.

2.5 How to import ESC - ESL package?

The “ECU list-GEMS” package can be downloaded from ComAp website (www.comap-control.com) and
imported into a PC software in the same way as a standard controller firmware package.
It can also be a part of an installation package, in this case it is not necessary to import it separately.

2.6 SAE - J1939 diagnostic connector

A Description of Off-Board diagnostic connector supposed to be used on engine to get the access to the
engine communication links.

Image 2.1 SAE - J1939 diagnostic connector

Pin label Meaning

A Battery negative
B Battery positive – unswitched
C CAN H
D CAN L
E CAN SHLD
F SAE J1708 +
G SAE J1708 -
H Proprietary OEM use
J Proprietary OEM use

ECU List – GEMS 2.3.0 Global Guide 7

2.7 How to create a constant for ECU control
There are at least two ways in GenConfig software:
By math function ADD in PLC where first input is a required analog value (constant) and the second input
is value 0. The output of the function is a constant which can be used as a source for ECU control. In this
example is created constant = 2.

Image 2.2 PLC constant for ECU control

By any of not used ExtValue1deflt - ExtValue4deflt setpoint. The value of an ExtValueXdeflt setpoint can
be used as a source for ECU control. It is recommended to use a source Logical 1 for a particular
ExtValueXreset (in LBI card).
There is a recommended way in DriveConfig software:
By math function ADD in PLC where first input is a required analog value (constant) and the second input
is value 0. The output of the function is a constant which can be used as a source for ECU control. In this
example is created constant = 2.

Image 2.3 PLC constant for ECU control

ECU List – GEMS 2.3.0 Global Guide 8

3 List of ECU
3.1 Altronic CD200XX and NGI1000 10
3.2 Altronic NGI 1000RC 12
3.3 GMF 14
3.4 Heinzmann Ariadne 16
3.5 Heinzmann Helenos 18
3.6 Heinzmann Kronos 19
3.7 Heinzmann Pandaros 20
3.8 Heinzmann Phlox 21
3.9 MWM ADEM A4 24
3.10 Powerlink 26
3.11 TPEM 27
3.12 Trijekt 33
3.13 Uninox 39
3.14 Varistep 1 41
3.15 Varistep 2 42

6 back to Table of contents

ECU List – GEMS 2.3.0 Global Guide 9

3.1 Altronic CD200XX and NGI1000
Modbus address: 1

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name Modbus Address Modbus name
Syncing 10001 Syncing
InSync1 10002 InSync1
InSync2 10003 InSync2
Purging 10004 Purging
Trying 10005 Trying
Firing 10006 Firing
LockOut 10007 LockOut
Fired 10008 Fired
Cranking 10009 Cranking
Running 10010 Running
Wrong Disk 10011 Wrong Disk
GLeadSDGround 10012 GLead SD Grounded
RemotePresent 10013 Remote Present
GLeadSDLogged 10014 GLead SD Logged
RemoteSDLogged 10015 Remote SD Logged
Overspeed Sd 10016 OverSpeed SD Logged
WDG1 Reset 10017 WDG1 Reset
WDG2 Reset 10018 WDG2 Reset
CheckSumError 10019 CheckSumError
LowSuppVolt 10020 Low Supply Voltage
NoCharge 10021 NoCharge
OpenPrimary 10022 OpenPrimary
ShortPrimary 10023 ShortPrimary
OpenSecond 10024 Open Secondary

ECU analog outputs (controller's inputs)

Configuration Name Modbus Address Modbus name
Engine Speed 30005 Engine Speed
Timming 30006 Timming
SwitchPosition 30007 Switch Position
CurrentLoop 30008 CurrentLoop
InsertRetard 30010 InsertRetard
SwitchRetard 30011 SwitchRetard
LoopRetard 30012 LoopRetard
RPMRetard 30013 RMPRetard
TotalRetard 30014 TotalRetard
Supply Voltage 30017 Supply Voltage
SparkRefOut A 30018 SparkRefOut A
SparkRefOut B 30019 SparkRefOut B

ECU List – GEMS 2.3.0 Global Guide 10

 SparkRefOut C 30020 SparkRefOut C
SparkRefOut D 30021 SparkRefOut D
SparkRefOut E 30022 SparkRefOut E
SparkRefOut F 30023 SparkRefOut F
SparkRefOut K 30024 SparkRefOut K
SparkRefOut L 30025 SparkRefOut L
SparkRefOut M 30026 SparkRefOut M
SparkRefOut N 30027 SparkRefOut N
SparkRefOut P 30028 SparkRefOut P
SparkRefOut R 30029 SparkRefOut R
SparkRefOut S 30030 SparkRefOut S
SparkRefOut T 30031 SparkRefOut T
SparkRefOut U 30032 SparkRefOut U
SparkRefOut V 30033 SparkRefOut V

ECU List – GEMS 2.3.0 Global Guide 11

3.2 Altronic NGI 1000RC
Modbus address: 11

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name Modbus Address Modbus name
Syncing 10001 Syncing
InSync1 10002 In Sync1
InSync2 10003 In Sync2
Purging 10004 Purging
Trying 10005 Trying
Firing 10006 Firing
LockOut 10007 Lock Out
Fired 10008 Fired
Cranking 10009 Cranking
Running 10010 Running
Wrong Disk 10011 Wrong Disk
GLeadSDGround 10012 GLead SD Grounded
RemotePresent 10013 Remote Present
GLeadSDLogged 10014 GLead SD Logged
RemoteSDLogged 10015 Remote SD Logged
Overspeed Sd 10016 OverSpeed SD Logged
WDOG1 Reset 10017 WDOG1 Reset
WDOG2 Reset 10018 WDOG2 Reset
CheckSumError 10019 CheckSumError
LowSuppVolt 10020 Low Supply Voltage
NoCharge 10021 No Charge
OpenPrimary 10022 Open Primary
ShortPrimary 10023 Short Primary
OpenSecond 10024 Open Secondary

ECU binary inputs (controller's outputs - commands)

Configuration Name Modbus Address Modbus name
Disk ON 1 Disk ON
TestForDisk 2 Test For Proper Disk
EnSecondDiag 3 Enable Secondary Diags
Slave 6 Slave
FallingEdge 7 Falling Edge
PowPickup 8 Powered Pickup

ECU analog outputs (controller's inputs)

Configuration Name Modbus Address Modbus name
Engine Speed 30005 Engine Speed
Timing 30006 Timing
SwitchPosition 30007 Switch Position

ECU List – GEMS 2.3.0 Global Guide 12

 CurrentLoop 30008 Current Loop
InsertRetard 30010 Insert Retard
SwitchRetard 30011 Switch Retard
LoopRetard 30012 Loop Retard
RPMRetard 30013 RMP Retard
TotalRetard 30014 Total Retard
Supply Voltage 30017 Supply Voltage
SparkRefOut A 30018 Spark Ref. Out A
SparkRefOut B 30019 Spark Ref. Out B
SparkRefOut C 30020 Spark Ref. Out C
SparkRefOut D 30021 Spark Ref. Out D
SparkRefOut E 30022 Spark Ref. Out E
SparkRefOut F 30023 Spark Ref. Out F
SparkRefOut K 30024 Spark Ref. Out K
SparkRefOut L 30025 Spark Ref. Out L
SparkRefOut M 30026 Spark Ref. Out M
SparkRefOut N 30027 Spark Ref. Out N
SparkRefOut P 30028 Spark Ref. Out P
SparkRefOut R 30029 Spark Ref. Out R
SparkRefOut S 30030 Spark Ref. Out S
SparkRefOut T 30031 Spark Ref. Out T
SparkRefOut U 30032 Spark Ref. Out U
SparkRefOut V 30033 Spark Ref. Out V

ECU analog inputs (controller's outputs)

Configuration Name Modbus Address Modbus name
Disk 40005 Disk Type Setting
LineUpAngle 40006 LineUp Angle Setting
InsertRetard 40007 Insertion Retard Setting
PurgeDelay 40008 Purge Delay Setting
Overspeed 40009 Overspeed Setting
RunSpeed 40010 Run Speed Setting
LowVoltage 40011 Low Voltage Setting
SlaveFiring 40012 Slave Firing
Duration 40013 Default Duration
Spark 40014 Default Spark
Global 40015 Default Global
Indv 40016 Default Indv
Cranks Log 40022 Cranks Log
Starts Log 40023 Starts Log
ColdBootLog 40024 Cold Boot Log
WarmBootLog 40025 Warm Boot Log
RemSparkDur 40100 Remote Control Spark Duration
Remote Spark 40101 Remote Spark
RemCtrlGlobRet 40102 Remote Control Global Retard

ECU List – GEMS 2.3.0 Global Guide 13

3.3 GMF
0x00
ECU address:
0x12

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
StatusOK - Overall Status OK
P-Zero - Zero Pressure Detection
FlowZero - Zero Flow Detection
NoFlow - Flow Not Reached
VlvPositionFlt - Valve Possition Error
T-ActuatorHi - High Actuator Temperature
T-ActuatorFlt - Actuator Temperature Fail
FGTFlt - FGT Fail
P-DiffFlt - Differential Pressure Fail
HiCurrCoilFlt - Coil Current Fail (High)
HiPositionFlt - Position Fail (High)
LowCurrCoilFlt - Coil Current Fail (Low)
FlowNotPlsb - Flow Not Plausible
LowPositionFlt - Position Fail (Low)
V-BatteryLow - Battery Voltage Error (Low)
FGTLowLimit - FGT Low Limit
P-DiffErrorLow - Differential Pressure Error (Low)
V-BatteryHi - Battery Voltage Error (High)
FGTHighLimit - FGT High Limit
P-DiffErrorHi - Differential Pressure Error (High)
FGPHighLimit - FGP High Limit
Watchdog - Watchdog
CanFlowDemFlt - Can Flow Demand Fail
TecjetSd - Tecjet Shutdown
GMFInternalFlt - GMF Internal Fault
Keyswitch - Keyswitch State

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
ActFuelValve - Actual Fuel Valve Position
DesFuelValve - Desired Fuel Valve Position
P-DiffGas - Outlet to Inlet Gas Differencial Pressure
FuelFlowRate - Fuel Flow Rate Low Bytes
FuelFlowRate - Fuel Flow Rate High Bytes

ECU analog inputs (controller's outputs)

Configuration Name SPN J1939 Name
FuelGravity - Fuel Specific Gravity

ECU List – GEMS 2.3.0 Global Guide 14

 HeatsRatio - Ratio of Specific Heats
FuelFlowRate - Fuel Flow Rate Low Bytes
FuelFlowRate - Fuel Flow Rate High Bytes

ECU List – GEMS 2.3.0 Global Guide 15

3.4 Heinzmann Ariadne
ECU address: 0x02

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
StopLamp 623 Red Stop Lamp
1,2,3,4,5,6,7,8
WarningLamp 624 Amber Warning Lamp
ProtectLamp 987 Protect Lamp
MalfunctLamp 1213 Malfunction Indicator Lamp

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
Cyl 1KnockLvl 1352 Engine Cylinder 1 Knock Level
Cyl 2KnockLvl 1353 Engine Cylinder 2 Knock Level
Cyl 3KnockLvl 1354 Engine Cylinder 3 Knock Level
Cyl 4KnockLvl 1355 Engine Cylinder 4 Knock Level
Cyl 5KnockLvl 1356 Engine Cylinder 5 Knock Level
Cyl 6KnockLvl 1357 Engine Cylinder 6 Knock Level
Cyl 7KnockLvl 1358 Engine Cylinder 7 Knock Level
Cyl 8KnockLvl 1359 Engine Cylinder 8 Knock Level
Cyl 9KnockLvl 1360 Engine Cylinder 9 Knock Level
Cyl10KnockLvl 1361 Engine Cylinder 10 Knock Level
Cyl11KnockLvl 1362 Engine Cylinder 11 Knock Level
Cyl12KnockLvl 1363 Engine Cylinder 12 Knock Level
Cyl13KnockLvl 1364 Engine Cylinder 13 Knock Level
Cyl14KnockLvl 1365 Engine Cylinder 14 Knock Level
Cyl15KnockLvl 1366 Engine Cylinder 15 Knock Level
Cyl16KnockLvl 1367 Engine Cylinder 16 Knock Level
Cyl17KnockLvl 1368 Engine Cylinder 17 Knock Level
Cyl18KnockLvl 1369 Engine Cylinder 18 Knock Level
Cyl19KnockLvl 1370 Engine Cylinder 19 Knock Level
Cyl20KnockLvl 1371 Engine Cylinder 20 Knock Level
Cyl21KnockLvl 1372 Engine Cylinder 21 Knock Level
Cyl22KnockLvl 1373 Engine Cylinder 22 Knock Level
Cyl23KnockLvl 1374 Engine Cylinder 23 Knock Level
Cyl24KnockLvl 1375 Engine Cylinder 24 Knock Level
KnockControl1 - Knock Control State 1
KnockControl2 - Knock Control State 2
KnockLevel - Engine Knock Level
ComRetardSpark - Common Spark Retard
KnockValue - Engine Knock Value
SparkRetard1 - Cylinder No 1 Spark Retard
SparkRetard2 - Cylinder No 2 Spark Retard
SparkRetard3 - Cylinder No 3 Spark Retard

ECU List – GEMS 2.3.0 Global Guide 16

 SparkRetard4 - Cylinder No 4 Spark Retard
SparkRetard5 - Cylinder No 5 Spark Retard
SparkRetard6 - Cylinder No 6 Spark Retard
SparkRetard7 - Cylinder No 7 Spark Retard
SparkRetard8 - Cylinder No 8 Spark Retard
SparkRetard9 - Cylinder No 9 Spark Retard
SparkRetard10 - Cylinder No 10 Spark Retard
SparkRetard11 - Cylinder No 11 Spark Retard
SparkRetard12 - Cylinder No 12 Spark Retard
SparkRetard13 - Cylinder No 13 Spark Retard
SparkRetard14 - Cylinder No 14 Spark Retard
SparkRetard15 - Cylinder No 15 Spark Retard
SparkRetard16 - Cylinder No 16 Spark Retard
SparkRetard17 - Cylinder No 17 Spark Retard
SparkRetard18 - Cylinder No 18 Spark Retard
SparkRetard19 - Cylinder No 19 Spark Retard
SparkRetard20 - Cylinder No 20 Spark Retard
SparkRetard21 - Cylinder No 21 Spark Retard
SparkRetard22 - Cylinder No 22 Spark Retard
SparkRetard23 - Cylinder No 23 Spark Retard
SparkRetard24 - Cylinder No 24 Spark Retard

ECU 32-bit analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
EngineRunHour 247 Engine Total Hours of Operation

ECU List – GEMS 2.3.0 Global Guide 17

3.5 Heinzmann Helenos
ECU address: 0x00

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
StopLamp 623 Red Stop Lamp
1,2,3,4,5,6,7,8
WarningLamp 624 Amber Warning Lamp
ProtectLamp 987 Protect Lamp
MalfunctLamp 1213 Malfunction Indicator Lamp

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
EngineSpeed 190 Engine Speed

ECU List – GEMS 2.3.0 Global Guide 18

3.6 Heinzmann Kronos
ECU address: 0x55

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
StopLamp 623 Red Stop Lamp
1,2,3,4,5,6,7,8
WarningLamp 624 Amber Warning Lamp
ProtectLamp 987 Protect Lamp
MalfunctLamp 1213 Malfunction Indicator Lamp

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
1,2,3,4,7,8
P-Intake 102 Engine Intake Manifold #1 Pressure
1,2,3,4,7,8
T-IntManifold 105 Engine Intake Manifold 1 Temperature
T-Exhaust 173 Engine Exhaust Temperature

ECU List – GEMS 2.3.0 Global Guide 19

3.7 Heinzmann Pandaros
ECU address: 0x0E

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
StopLamp 623 Red Stop Lamp
1,2,3,4,5,6,7,8
WarningLamp 624 Amber Warning Lamp
ProtectLamp 987 Protect Lamp
MalfunctLamp 1213 Malfunction Indicator Lamp

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
APP 91 Accelerator Pedal Position 1
1,2,3,4,5,6,7,8
Load 92 Engine Percent Load At Current Speed
1,2,3,4,5,6,7,8
P-Oil 100 Engine Oil Pressure
1,2,3,4,7,8
P-Intake 102 Engine Intake Manifold #1 Pressure
1,2,3,4,7,8
T-IntManifold 105 Engine Intake Manifold 1 Temperature
1,2,3,4,5,6,7,8
T-Coolant 110 Engine Coolant Temperature
Battery 168 Battery Potential / Power Input 1
T-Exhaust 173 Engine Exhaust Temperature
T-Fuel 174 Engine Fuel 1 Temperature 1
T-Oil 175 Engine Oil Temperature 1
1,2,3,4,5,6,7,8
EngineSpeed 190 Engine Speed
TorqueDemand 512 Driver's Demand Engine - Percent Torque
TorqueActual 513 Actual Engine - Percent Torque
Torque 514 Nominal Friction - Percent Torque
TorqMode 899 Engine Torque Mode
FuelRack 1210 Engine Fuel Rack Position

ECU analog inputs (controller's outputs)

Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
Spd-Requested 898 Engine Requested Speed/Speed Limit

ECU List – GEMS 2.3.0 Global Guide 20

3.8 Heinzmann Phlox
ECU address: 0x34

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
1,2,3,4,5,6,7,8
StopLamp 623 Red Stop Lamp
1,2,3,4,5,6,7,8
WarningLamp 624 Amber Warning Lamp
ProtectLamp 987 Protect Lamp

ECU binary inputs (controller's outputs - commands)

Configuration Name SPN J1939 Name
IgnitionStop - Ignition stop

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
Cyl 1 Timing - Engine cylinder 1 ignition timing
Cyl 2 Timing - Engine cylinder 2 ignition timing
Cyl 3 Timing - Engine cylinder 3 ignition timing
Cyl 4 Timing - Engine cylinder 4 ignition timing
Cyl 5 Timing - Engine cylinder 5 ignition timing
Cyl 6 Timing - Engine cylinder 6 ignition timing
Cyl 7 Timing - Engine cylinder 7 ignition timing
Cyl 8 Timing - Engine cylinder 8 ignition timing
Cyl 9 Timing - Engine cylinder 9 ignition timing
Cyl 10 Timing - Engine cylinder 10 ignition timing
Cyl 11 Timing - Engine cylinder 11 ignition timing
Cyl 12 Timing - Engine cylinder 12 ignition timing
Cyl 13 Timing - Engine cylinder 13 ignition timing
Cyl 14 Timing - Engine cylinder 14 ignition timing
Cyl 15 Timing - Engine cylinder 15 ignition timing
Cyl 16 Timing - Engine cylinder 16 ignition timing
Cyl 17 Timing - Engine cylinder 17 ignition timing
Cyl 18 Timing - Engine cylinder 18 ignition timing
Cyl 19 Timing - Engine cylinder 19 ignition timing
Cyl 20 Timing - Engine cylinder 20 ignition timing
Cyl 21 Timing - Engine cylinder 21 ignition timing
Cyl 22 Timing - Engine cylinder 22 ignition timing
Cyl 23 Timing - Engine cylinder 23 ignition timing
Cyl 24 Timing - Engine cylinder 24 ignition timing
Cyl 1 Energy - Engine cylinder 1 ignition energy
Cyl 2 Energy - Engine cylinder 2 ignition energy
Cyl 3 Energy - Engine cylinder 3 ignition energy
Cyl 4 Energy - Engine cylinder 4 ignition energy
Cyl 5 Energy - Engine cylinder 5 ignition energy

ECU List – GEMS 2.3.0 Global Guide 21

 Cyl 6 Energy - Engine cylinder 6 ignition energy
Cyl 7 Energy - Engine cylinder 7 ignition energy
Cyl 8 Energy - Engine cylinder 8 ignition energy
Cyl 9 Energy - Engine cylinder 9 ignition energy
Cyl 10 Energy - Engine cylinder 10 ignition energy
Cyl 11 Energy - Engine cylinder 11 ignition energy
Cyl 12 Energy - Engine cylinder 12 ignition energy
Cyl 13 Energy - Engine cylinder 13 ignition energy
Cyl 14 Energy - Engine cylinder 14 ignition energy
Cyl 15 Energy - Engine cylinder 15 ignition energy
Cyl 16 Energy - Engine cylinder 16 ignition energy
Cyl 17 Energy - Engine cylinder 17 ignition energy
Cyl 18 Energy - Engine cylinder 18 ignition energy
Cyl 19 Energy - Engine cylinder 19 ignition energy
Cyl 20 Energy - Engine cylinder 20 ignition energy
Cyl 21 Energy - Engine cylinder 21 ignition energy
Cyl 22 Energy - Engine cylinder 22 ignition energy
Cyl 23 Energy - Engine cylinder 23 ignition energy
Cyl 24 Energy - Engine cylinder 24 ignition energy
Cyl 1 Spark - Engine cylinder 1 spark duration
Cyl 2 Spark - Engine cylinder 2 spark duration
Cyl 3 Spark - Engine cylinder 3 spark duration
Cyl 4 Spark - Engine cylinder 4 spark duration
Cyl 5 Spark - Engine cylinder 5 spark duration
Cyl 6 Spark - Engine cylinder 6 spark duration
Cyl 7 Spark - Engine cylinder 7 spark duration
Cyl 8 Spark - Engine cylinder 8 spark duration
Cyl 9 Spark - Engine cylinder 9 spark duration
Cyl 10 Spark - Engine cylinder 10 spark duration
Cyl 11 Spark - Engine cylinder 11 spark duration
Cyl 12 Spark - Engine cylinder 12 spark duration
Cyl 13 Spark - Engine cylinder 13 spark duration
Cyl 14 Spark - Engine cylinder 14 spark duration
Cyl 15 Spark - Engine cylinder 15 spark duration
Cyl 16 Spark - Engine cylinder 16 spark duration
Cyl 17 Spark - Engine cylinder 17 spark duration
Cyl 18 Spark - Engine cylinder 18 spark duration
Cyl 19 Spark - Engine cylinder 19 spark duration
Cyl 20 Spark - Engine cylinder 20 spark duration
Cyl 21 Spark - Engine cylinder 21 spark duration
Cyl 22 Spark - Engine cylinder 22 spark duration
Cyl 23 Spark - Engine cylinder 23 spark duration
Cyl 24 Spark - Engine cylinder 24 spark duration
Cyl 1 Error - Engine cylinder 1 error state
Cyl 2 Error - Engine cylinder 2 error state
Cyl 3 Error - Engine cylinder 3 error state
Cyl 4 Error - Engine cylinder 4 error state
Cyl 5 Error - Engine cylinder 5 error state

ECU List – GEMS 2.3.0 Global Guide 22

 Cyl 6 Error - Engine cylinder 6 error state
Cyl 7 Error - Engine cylinder 7 error state
Cyl 8 Error - Engine cylinder 8 error state
Cyl 9 Error - Engine cylinder 9 error state
Cyl 10 Error - Engine cylinder 10 error state
Cyl 11 Error - Engine cylinder 11 error state
Cyl 12 Error - Engine cylinder 12 error state
Cyl 13 Error - Engine cylinder 13 error state
Cyl 14 Error - Engine cylinder 14 error state
Cyl 15 Error - Engine cylinder 15 error state
Cyl 16 Error - Engine cylinder 16 error state
Cyl 17 Error - Engine cylinder 17 error state
Cyl 18 Error - Engine cylinder 18 error state
Cyl 19 Error - Engine cylinder 19 error state
Cyl 20 Error - Engine cylinder 20 error state
Cyl 21 Error - Engine cylinder 21 error state
Cyl 22 Error - Engine cylinder 22 error state
Cyl 23 Error - Engine cylinder 23 error state
Cyl 24 Error - Engine cylinder 24 error state

ECU analog inputs (controller's outputs)

Configuration Name SPN J1939 Name
IgnitionTiming - Common ignition timing
IgnitionEnergy - Common ignition energy

ECU List – GEMS 2.3.0 Global Guide 23

3.9 MWM ADEM A4
ECU address: 0x00

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
FuelShtoff1 632 Engine Fuel Shutoff 1 Control
FuelShtoff2 2807 Engine Fuel Shutoff 2 Control
PTO Enabled 3452 Enable Switch - Transmission input shaft PTO 1
ESDRequest 3607 Engine Emergency (Immediate) Shutdown Indication

ECU binary inputs (controller's outputs - commands)

Configuration Name SPN J1939 Name

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
ThrottleVlv1 51 Engine Throttle Valve 1 Position 1
T-Intcooler 52 Engine Intercooler Temperature
1,2,3,4,5,6,7,8
Load 92 Engine Percent Load At Current Speed
OilLevel 98 Engine Oil Level
1,2,3,4,5,6,7,8
P-Oil 100 Engine Oil Pressure
P-Crankcase 101 Engine Crankcase Pressure 1
1,2,3,4,7,8
T-IntManifold 105 Engine Intake Manifold 1 Temperature
P-Coolant1 109 Engine Coolant Pressure 1
1,2,3,4,5,6,7,8
T-Coolant 110 Engine Coolant Temperature
Battery 168 Battery Potential / Power Input 1
T-AirIntake 172 Engine Intake 1 Air Temperature
T-Oil 175 Engine Oil Temperature 1
1,2,3,4,5,6,7,8
EngineSpeed 190 Engine Speed
Spd-Desired* 515 Engine's Desired Operating Speed
T-Turbo1CInt 1172 Engine Turbocharger 1 Compressor Intake Temperature
TurboWstAct1 1188 Engine Turbocharger Wastegate Actuator 1 Position
Cyl 1KnockLvl 1352 Engine Cylinder 1 Knock Level
Cyl 2KnockLvl 1353 Engine Cylinder 2 Knock Level
Cyl 3KnockLvl 1354 Engine Cylinder 3 Knock Level
Cyl 4KnockLvl 1355 Engine Cylinder 4 Knock Level
Cyl 5KnockLvl 1356 Engine Cylinder 5 Knock Level
Cyl 6KnockLvl 1357 Engine Cylinder 6 Knock Level
Cyl 7KnockLvl 1358 Engine Cylinder 7 Knock Level
Cyl 8KnockLvl 1359 Engine Cylinder 8 Knock Level
Cyl 9KnockLvl 1360 Engine Cylinder 9 Knock Level
Cyl10KnockLvl 1361 Engine Cylinder 10 Knock Level
Cyl11KnockLvl 1362 Engine Cylinder 11 Knock Level
Cyl12KnockLvl 1363 Engine Cylinder 12 Knock Level
Cyl13KnockLvl 1364 Engine Cylinder 13 Knock Level

ECU List – GEMS 2.3.0 Global Guide 24

 Cyl14KnockLvl 1365 Engine Cylinder 14 Knock Level
Cyl15KnockLvl 1366 Engine Cylinder 15 Knock Level
Cyl16KnockLvl 1367 Engine Cylinder 16 Knock Level
IgnitionTime 1436 Engine Actual Ignition Timing
FuelVlvPos1 1442 Engine Fuel Valve 1 Position
ThrottleCmd 3464 Engine Throttle Actuator 1 Control Command
Operating 3543 Engine Operating State
P-IntakeManAbs 3563 Engine Intake Manifold #1 Absolute Pressure
DerateRequest 3644 Engine Derate Request
T-Coolant2 4076 Engine Coolant Temperature 2
P-IntManAbs 4817 Engine Intake Manifold 1 Absolute Pressure (High Resolution)
TurboWstgAct1 5386 Engine Turbocharger Wastegate Actuator 1 Command
P-ThrottleDiff 5631 Engine Throttle Valve 1 Differential Pressure
SpplGasMethane 5867 Supply Gas Methane Percentage
CYL temp A1 10739 Cylinder Temperature A1
CYL temp A2 10740 Cylinder Temperature A2
CYL temp A3 10741 Cylinder Temperature A3
CYL temp A4 10742 Cylinder Temperature A4
CYL temp A5 10743 Cylinder Temperature A5
CYL temp A6 10744 Cylinder Temperature A6
CYL temp A7 10745 Cylinder Temperature A7
CYL temp A8 10746 Cylinder Temperature A8
CYL temp B1 10747 Cylinder Temperature B1
CYL temp B2 10748 Cylinder Temperature B2
CYL temp B3 10749 Cylinder Temperature B3
CYL temp B4 10750 Cylinder Temperature B4
CYL temp B5 10751 Cylinder Temperature B5
CYL temp B6 10752 Cylinder Temperature B6
CYL temp B7 10753 Cylinder Temperature B7
CYL temp B8 10754 Cylinder Temperature B8

*The parameter requires extended controller's support. Please refer controller's manual for further
information.

ECU List – GEMS 2.3.0 Global Guide 25

3.10 Powerlink
ECU address: 0x00

Available parameters
ECU analog outputs (controller's inputs)
Configuration Name SPN J1939 Name
ThrottleVlv1 51 Engine Throttle Valve 1 Position 1
1,2,3,4,5,6,7
P-Oil 100 Engine Oil Pressure
1,2,3,4,7
T-IntManifold 105 Engine Intake Manifold 1 Temperature
P-IntakeAir 106 Engine Intake Air Pressure
1,2,3,4,5,6,7
T-Coolant 110 Engine Coolant Temperature
T-Exhaust 173 Engine Exhaust Temperature
1,2,3,4,7
T-Oil 175 Engine Oil Temperature 1
1,2,3,4,5,6,7
EngineSpeed 190 Engine Speed
T-ExhPort 1 1137 Engine Exhaust Gas Port 1 Temperature
T-ExhPort 2 1138 Engine Exhaust Gas Port 2 Temperature
T-ExhPort 3 1139 Engine Exhaust Gas Port 3 Temperature
T-ExhPort 4 1140 Engine Exhaust Gas Port 4 Temperature
T-ExhPort 5 1141 Engine Exhaust Gas Port 5 Temperature
T-ExhPort 6 1142 Engine Exhaust Gas Port 6 Temperature
T-ExhPort 7 1143 Engine Exhaust Gas Port 7 Temperature
T-ExhPort 8 1144 Engine Exhaust Gas Port 8 Temperature
T-ExhPort 9 1145 Engine Exhaust Gas Port 9 Temperature
T-ExhPort10 1146 Engine Exhaust Gas Port 10 Temperature
T-ExhPort11 1147 Engine Exhaust Gas Port 11 Temperature
T-ExhPort12 1148 Engine Exhaust Gas Port 12 Temperature
T-ExhPort13 1149 Engine Exhaust Gas Port 13 Temperature
T-ExhPort14 1150 Engine Exhaust Gas Port 14 Temperature
T-ExhPort15 1151 Engine Exhaust Gas Port 15 Temperature
T-ExhPort16 1152 Engine Exhaust Gas Port 16 Temperature
T-ExhPort17 1153 Engine Exhaust Gas Port 17 Temperature
T-ExhPort18 1154 Engine Exhaust Gas Port 18 Temperature
T-ExhPort19 1155 Engine Exhaust Gas Port 19 Temperature
T-ExhPort20 1156 Engine Exhaust Gas Port 20 Temperature
P-FuelIntake 1390 Engine Fuel Valve 1 Intake Absolute Pressure
IgnitionTime1 1433 Engine Desired Ignition Timing 1

ECU List – GEMS 2.3.0 Global Guide 26

3.11 TPEM
Modbus address: 1

Available parameters
ECU binary outputs (controller's inputs)
Modbus
Configuration Name Modbus Name
Address
T604 CV 11002 T604 CV exhaust air sensor error
T404 CV 11003 T404 CV supply air 10 K too high
G987 CV 11004 G987 CV inlet flap limit stop opened
G988 CV 11005 G988 CV inlet flap limit stop closed
G350 CV 11006 G350 CV outlet flap limit stop opened
G351 CV 11007 G351 CV outlet flap limit stop closed
G555 CV 11008 G555 CV circulation flap limit stop opened
G354 CV 11009 G354 CV circulation flap limit stop closed
G885 MCC Warm 11010 G885 MCC control valve limit stop warm
G886 MCC Cold 11011 G886 MCC control valve limit stop cold
MCC340 11012 340 MCC Rec FC demanded
G880 HC 11016 G880 HC valve limit stop cold
G881 HC 11017 G881 HC valve limit stop warm
631 ECC Pump 11018 631 ECC pump demanded
HC Pump 11019 HC pump demanded
G890 EmCC Cold 11020 G890 EmCC valve limit stop cold
G891 EmCC Warm 11021 G891 EmCC valve limit stop warm
938 EmCC Pump 11022 938 EmCC pump demanded
CPH demanded 11023 CPH demanded
Power Lim Op 1 11024 Power limitation by mains operator level 1
Power Lim Op 2 11025 Power limitation by mains operator level 2
Power Lim Op 3 11026 Power limitation by mains operator level 3
Power Lim Op 4 11027 Power limitation by mains operator level 4
Aut Power Dem 11028 Automatic power demand active
GCB Closed 11029 GCB closed
MCB Closed 11030 MCB closed
GCB Release 11031 GCB release
Automatic 11032 Automatic
RP OverF 11033 Mains-dependent RP active in the event of overfrequency
CV Control 11034 CV control at standstill active
BlackStartRun 11035 Black start running
BlackStartPos 11037 Black start possible
StarterDem 11038 Starter demanded in
PrelubPumpIn 11039 Prelubrication pump demanded in
GCL A 1 11040 GCL A gas shut-off valve 1 demanded
GCL A 2 11041 GCL A gas shut-off valve 2 demanded
GCL A Leak 11052 GCL A leakage check demanded
FreshOilDem 11053 Fresh oil refill demanded
T207 ECC High 11054 T207 ECC engine inlet too high

ECU List – GEMS 2.3.0 Global Guide 27

 T206 ECC Low 11055 T206 ECC engine outlet too low
T208 Lube Low 11056 T208 lube oil engine inlet too low (warm-up failed)
S200 Engine 11057 S200 engine speed gradient too high
996 GCB UnexO 11058 996 GCB opened unexpectedly
GAM A Failed 11059 GAM A mobility test failed
T203 Comm Err 11060 T203 intake air row A communication error (irregular data transfer)
T203 A High 11061 T203 intake air row A too high
P232ErrBatt 11062 P232 receiver A sensor error (short-circuit to battery)
P232ErrGnd 11063 P232 receiver A sensor error (short-circuit to ground)
S200 Implaus 11064 S200 engine speed gradient implausible
G197 Dev Err 11065 G197 TV A device error (value incorrect)
G273 Sens Err 11066 G273 WG sensor error (value incorrect)
T201 A High 11067 T201 receiver A too high
G867 ECC Cold 11077 G867 ECC valve limit stop cold
G868 ECC Warm 11078 G868 ECC valve limit stop warm
CounterOF-C 11079 Counter overflow (start with closed GCB)
CounterOF-N 11080 Counter overflow (normal start)
CounterOF-B 11081 Counter overflow (black start)
EmCC Rec 1 11082 EmCC Rec stage 1 active
EmCC Rec 2 11083 EmCC Rec stage 2 active
EmCC Rec 3 11084 EmCC Rec stage 3 active
EmCC Rec 4 11085 EmCC Rec stage 4 active
EmCC Rec 5 11086 EmCC Rec stage 5 active
EmCC Rec 6 11087 EmCC Rec stage 6 active
EmCC Rec 7 11088 EmCC Rec stage 7 active
EmCC Rec 8 11089 EmCC Rec stage 8 active
MCC Rec 1 11090 MCC Rec stage 1 active
MCC Rec 2 11091 MCC Rec stage 2 active
MCC Rec 3 11092 MCC Rec stage 3 active
MCC Rec 4 11093 MCC Rec stage 4 active
MCC Rec 5 11094 MCC Rec stage 5 active
MCC Rec 6 11095 MCC Rec stage 6 active
MCC Rec 7 11096 MCC Rec stage 7 active
MCC Rec 8 11097 MCC Rec stage 8 active
P127 GCL B Low 11098 P127 GCL B too low
GCL B Leak 11099 GCL B leakage check demanded
P124 GCL Low 11100 P124 GCL A gas too low - 1099
P-SetErr-CB 11101 P set prechamber gas pressure controller (cable break)
P-SetErr-SC 11102 P set prechamber gas pressure controller (short-circuit)
GC Angle High 11103 Grid code: ignition angle correction too high (adjusts late)
Engine Warmed 11104 Engine warmed up, knock detection fully active
EHE Bypass Act 11239 EHE bypass control activated
EHEBypassClos 11240 EHE bypass limit stop closed
EHEBypassOpen 11241 EHE bypass flap limit stop opened
MCCPumpDem 11242 MCC pump demanded
IAP pump 11251 IAP pump active
IAP Valve AB-B 11252 IAP Valve limit stop closed (AB-B)
IAP valve AB-B 11253 IAP valve limit stop open (AB-A)

ECU List – GEMS 2.3.0 Global Guide 28

 Err 13194 T404 CV supply air sensor error
T404CVHigh15K 13195 T404 CV supply air 15 K too high
T404CVHigh20K 13196 T404 CV supply air 20 K too high
335 MCC pump F 13197 335 MCC pump failed
336 ECC pump F 13198 336 ECC pump failed
P157 13222 P157 exhaust back pressure too high
P124 13601 P124 GCL A gas too low - 3600
P309 15057 P309 diff MC too low
L308 15099 SaC MCC liquid too low
L123 15100 SaC ECC liquid too low
L458 15101 SaC EmCC liquid too low
P281 15108 P281 P diff HC too low
P126 15120 P126 diff ECC too low
450 NOxdailyH 16029 450 NOx daily mean value too high
450 O2 daily H 16030 450 O2 daily mean value too high
StarterDemOut 10163 Starter demanded out
PrelubPumpD 10165 Prelubrication pump demanded out
Gas valve A1 10184 Gas shut-off valve A1
Gas valve A2 10185 Gas shut-off valve A2
GCB Feedback 10417 GCB position feedback
MCB Feedback 10418 MCB position feedback
Gen Running FB 10641 Genset running feedback
Col Alarm 10642 Collective alarm
Col Wrn 10643 Collective warning
OilRefillDem 10644 Fresh oil refill demanded out

ECU analog outputs (controller's inputs)

Modbus
Configuration Name Modbus Name
Address
OperationMode 30002 Operation mode
P302 30205 Filter A outlet lube oil - P302
T208 30206 Engine inlet lube oil - T208
L234 30208 Oil tray - L234
L327 30209 Oil reservoir - L327
P145 30210 Crankcase - P145
T203 30215 Intake air row A - T203
T201 30217 Receiver A - T201
E149 30222 TPEM CU supply voltage - E149
G197.1 30223 TV A - G197.1
S200 30224 Engine - S200
E198.5 30226 Set power - E198.5
E198.2 30227 Power - E198.2
S200.4 30228 Set engine before adjustment - S200.4
E198.6 30231 Permissible power - E198.6
T206 30242 ECC engine outlet - T206
T207 30243 ECC engine inlet - T207
T434 30245 T MCC LT high pressure - T434
T202 30248 MC inlet - T202

ECU List – GEMS 2.3.0 Global Guide 29

 T459 30270 Generator bearing A - T459
T460 30271 Generator bearing B - T460
T209 30272 Generator winding U - T209
T210 30273 Generator winding V - T210
T211 30274 Generator winding W - T211
T487 30275 Generator inlet air - T487
T488 30276 Generator outlet air - T488
Plant status 30280 Plant status
SC Al RemT Sd 30283 Remaining time until the genset shuts down in the event of Alarm SC
OperHours 30286 Genset total operating hours
T461 30294 Combustion chamber A1 - T461
T462 30295 Combustion chamber A2 - T462
T463 30296 Combustion chamber A3 - T463
T464 30297 Combustion chamber A4 - T464
T465 30298 Combustion chamber A5 - T465
T466 30299 Combustion chamber A6 - T466
T467 30300 Combustion chamber A7 - T467
T468 30301 Combustion chamber A8 - T468
T469 30302 Combustion chamber A9 - T469
T470 30303 Combustion chamber A10 - T470
T471 30304 Combustion chamber B1 - T471
T472 30305 Combustion chamber B2 - T472
T473 30306 Combustion chamber B3 - T473
T474 30307 Combustion chamber B4 - T474
T475 30308 Combustion chamber B5 - T475
T476 30309 Combustion chamber B6 - T476
T477 30310 Combustion chamber B7 - T477
T478 30311 Combustion chamber B8 - T478
T479 30312 Combustion chamber B9 - T479
T480 30313 Combustion chamber B10 - T480
CombCh Tmean 30252 T mean combustion chamber
CombCh Tset 30354 T set combustion chamber
CombCh Tred 30356 Reduction T set combustion chamber (knocking)
G159.9 30371 GAM - G159.9
G163.1 30373 GAM A start position - G163.1
G197.3 30375 Set TV A - G197.3
P320 30379 Diff TV A - P320
RP-T207 30391 RP by percent (T207 ECC too high)
RP-T201 30392 RP by percent (T201 receiver too high)
RP-S-ETC 30393 RP by percent (S ETC too high)
RP-knocking 30394 RP by percent (knocking)
RP-G-TV 30395 RP by percent (G TV)
RP-sensor-err 30396 RP by percent (sensor error T combustion chamber)
RP-warning 30398 RP by percent (warning RP)
Mains f 30408 Mains frequency
Gen PF act 30413 Generator PF actual value
Bus f 30415 Busbar frequency
PowerDemanded 30419 Power demanded

ECU List – GEMS 2.3.0 Global Guide 30

 Gen Power 30427 Generator power (kW)
Gen f 30428 Generator frequency
Gen V L1-2 30429 Generator voltage L1-2
Gen V L2-3 30430 Generator voltage L2-3
Gen V L3-1 30431 Generator voltage L3-1
Gen V L1-N 30432 Generator voltage L1-N
Gen V L2-N 30433 Generator voltage L2-N
Gen V L3-N 30434 Generator voltage L3-N
Gen curr L1 30438 Generator current L1
Gen curr L2 30439 Generator current L2
Gen curr L3 30440 Generator current L3
Mains V L1-2 30441 Mains voltage L1-2
Mains V L2-3 30442 Mains voltage L2-3
Mains V L3-1 30443 Mains voltage L3-1
Mains V L1-N 30444 Mains voltage L1-N
Mains V L2-N 30445 Mains voltage L2-N
Mains V L3-N 30446 Mains voltage L3-N
Bus V 30447 Busbar voltage
Mains f HiRes 30448 Mains frequency high resolution
IgnitAngleadj 30506 Ignition angle adjustment
IgnitAmaxadj 30507 Ignition angle max adjustment
IgnitionAngle 30508 Ignition angle
Ign A A1 30509 Ignition angle A1
Ign A A2 30510 Ignition angle A2
Ign A A3 30511 Ignition angle A3
Ign A A4 30512 Ignition angle A4
Ign A A5 30513 Ignition angle A5
Ign A A6 30514 Ignition angle A6
Ign A A7 30515 Ignition angle A7
Ign A A8 30516 Ignition angle A8
Ign A A9 30517 Ignition angle A9
Ign A A10 30518 Ignition angle A10
Ign A B1 30519 Ignition angle B1
Ign A B2 30520 Ignition angle B2
Ign A B3 30521 Ignition angle B3
Ign A B4 30522 Ignition angle B4
Ign A B5 30523 Ignition angle B5
Ign A B6 30524 Ignition angle B6
Ign A B7 30525 Ignition angle B7
Ign A B8 30526 Ignition angle B8
Ign A B9 30527 Ignition angle B9
Ign A B10 30528 Ignition angle B10
P497 30531 ECC engine outlet - P497
T496 30553 Exhaust gas CAT B outlet - T496
T286 30556 Exhaust gas engine outlet - T286
T287 30557 Exhaust gas CAT A outlet - T287
T288 30558 Exhaust gas EHE outlet - T288
T404 30561 CV supply air - T404

ECU List – GEMS 2.3.0 Global Guide 31

 T604 30562 CV exhaust air - T604
T291 30581 HC supply flow - T291
T289 30582 HC return flow - T289
T412 30583 ECC EHE outlet - T412
T384 30584 EmCC inlet - T384
T290 30585 HC CWHE inlet - T290
T386 30586 HC LHE inlet - T386
T385 30587 HC EHE inlet - T385
T419 30591 EmCC Rec outlet - T419
T405 30596 MCC Rec outlet - T405
G273.1 30633 Actual WG - G273.1
G273.3 30634 Set WG - G273.3
P232 30645 Receiver A - P232
Normal starts 30648 Number of normal starts
Black starts 30649 Number of black starts
GCB c starts 30650 Number of starts with closed GCB
EnergyAmount 30651 Amount of energy generated to date
Gen PF disc 30680 Generator discrete PF

ECU analog inputs (controller's outputs)

Modbus
Configuration Name Modbus Name
Address
PowerDem(prot) 41026 Power demanded (protocol)
PF 41203 PF setpoint value per Modbus
Q 41204 Reactive power value (Q) given via Modbus
Discrete PF 41243 Discrete PF setpoint value per Modbus
Offset f(M) 41254 Offset to current mains frequency Modbus
U demand 41255 U demand Modbus

ECU List – GEMS 2.3.0 Global Guide 32

3.12 Trijekt
ECU address: 0x00

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
ReadyStart - Ready to Start
DInEngEn - Dig. Input Engine Enable
DInTypOp - Dig. Input Type of Operation
DInOpPhase - Dig. Input Operation Phase
DinPlus - Dig. Input Plus
DInMinus - Dig. Input Minus
DInF1 - Dig. Input Function 1
DInF2 - Dig. Input Function 2
DInF3 - Dig. Input Function 3
DInF4 - Dig. Input Function 4
DInF5 - Dig. Input Function 5
DInF6 - Dig. Input Function 6
DInF7 - Dig. Input Function 7
DInF8 - Dig. Input Function 8
DOutIgnLoA - Dig. Output Ign. Low A
DOutIgnLoB - Dig. Output Ign. Low B
DOutIgnLoC - Dig. Output Ign. Low C
DOutIgnLoD - Dig. Output Ign. Low D
DOutIgnLoE - Dig. Output Ign. Low E
DOutIgnLoF - Dig. Output Ign. Low F
DOutIgnLoG - Dig. Output Ign. Low G
DOutIgnLoH - Dig. Output Ign. Low H
DOutIgnHiA - Dig. Output Ign. High A
DOutIgnHiB - Dig. Output Ign. High B
DOutIgnHiC - Dig. Output Ign. High C
DOutIgnHiD - Dig. Output Ign. High D
DOutIgnHiE - Dig. Output Ign. High E
DOutIgnHiF - Dig. Output Ign. High F
DOutIgnHiG - Dig. Output Ign. High G
DOutIgnHiH - Dig. Output Ign. High H
DOutSw1 - Dig. Output Switch 1
DOutSw2 - Dig. Output Switch 2
DOutSw3 - Dig. Output Switch 3
DOutSw4 - Dig. Output Switch 4
DOutSw5 - Dig. Output Switch 5
DOutSw6 - Dig. Output Switch 6
DOutSw7 - Dig. Output Switch 7
DOutSw8 - Dig. Output Switch 8
DOutSw9 - Dig. Output Switch 9

ECU List – GEMS 2.3.0 Global Guide 33

 DOutSw10 - Dig. Output Switch 10
Flag1 - Flag1
Flag2 - Flag2
Flag3 - Flag3
Flag4 - Flag4
Flag5 - Flag5
Flag6 - Flag6
Flag7 - Flag7
Flag8 - Flag8
Flag9 - Flag9
Flag10 - Flag10
Flag11 - Flag11
Flag12 - Flag12
Flag13 - Lambda Corr. Bit 0 (Flag 13)
Flag14 - Lambda Corr. Bit 0 (Flag 14)
Flag15 - Ign. Corr. Bit 0 (Flag 15)
Flag16 - Ign. Corr. Bit 1 (Flag 16)
Flag17 - Ready to Start (Flag 17)
Flag18 - Start Request (Flag 18)
Flag19 - Flag 19
Flag20 - Lambda Corr. Bit 0 (Flag 20)
Flag21 - Lambda Corr. Bit 0 (Flag 21)
Flag22 - Flag 22
Flag23 - Flag 23
Flag24 - Flag 24
Flag25 - Flag 25
Flag26 - Flag 26
Flag27 - Flag 27
Flag28 - Flag 28
Flag29 - Knock Control On(Flag 29)
Flag30 - Gas valve Off (Flag 30)
Flag31 - Load Control Pos. Bit1(Flag 31)
Flag32 - Load Control Pos. Bit1(Flag 32)
1,2,3,4,5,6,7,8
StopLamp 623 Red Stop Lamp
1,2,3,4,5,6,7,8
WarningLamp 624 Amber Warning Lamp
ProtectLamp 987 Protect Lamp
MalfunctLamp 1213 Malfunction Indicator Lamp
ECM1Lamp 6205 Engine Control Module 1 Ready for Use Lamp Command

ECU binary inputs (controller's outputs - commands)

Configuration Name SPN J1939 Name
Start Req - Start Request
Stop Req - Stop Request
KnockOn - Knock Control On
GasOff - Gas Valve Off
Flag 1 - Flag 1
Flag 2 - Flag 2
Flag 3 - Flag 3

ECU List – GEMS 2.3.0 Global Guide 34

 Flag 4 - Flag 4
Flag 5 - Flag 5
Flag 6 - Flag 6
Flag 7 - Flag 7
Flag 8 - Flag 8
Flag 9 - Flag 9
Flag 10 - Flag 10
Flag 11 - Flag 11
Flag 12 - Flag 12
Flag 13 - Lambda Corr. Bit 0 (Flag 13)
Flag 14 - Lambda Corr. Bit 0 (Flag 14)
Flag 15 - Ign. Corr. Bit 0 (Flag 15)
Flag 16 - Ign. Corr. Bit 1 (Flag 16)
Flag 17 - Ready to Start (Flag 17)
Flag 18 - Start Request (Flag 18)
Flag 19 - Flag 19
Flag 20 - Lambda Corr. Bit 0 (Flag 20)
Flag 21 - Lambda Corr. Bit 0 (Flag 21)
Flag 22 - Flag 22
Flag 23 - Flag 23
Flag 24 - Flag 24
Flag 25 - Flag 25
Flag 26 - Flag 26
Flag 27 - Flag 27
Flag 28 - Flag 28
Flag 29 - Knock Control On(Flag 29)
Flag 30 - Gas valve Off (Flag 30)
Flag 31 - Load Control Pos. Bit1(Flag 31)
Flag 32 - Load Control Pos. Bit1(Flag 32)
DOutIgnLoA 5984 Dig. Output Ign. Low A
DOutIgnLoB 5985 Dig. Output Ign. Low B
DOutIgnLoC 5986 Dig. Output Ign. Low C
DOutIgnLoD 5987 Dig. Output Ign. Low D
DOutIgnLoE 5988 Dig. Output Ign. Low E
DOutIgnLoF 5989 Dig. Output Ign. Low F
DOutIgnLoG 5990 Dig. Output Ign. Low G
DOutIgnLoH 5991 Dig. Output Ign. Low H
DOutIgnHiA 5992 Dig. Output Ign. High A
DOutIgnHiB 5993 Dig. Output Ign. High B
DOutIgnHiC 5994 Dig. Output Ign. High C
DOutIgnHiD 5995 Dig. Output Ign. High D
DOutIgnHiE 5996 Dig. Output Ign. High E
DOutIgnHiF 5997 Dig. Output Ign. High F
DOutIgnHiG 5998 Dig. Output Ign. High G
DOutIgnHiH 5999 Dig. Output Ign. High H
DOutSw1 6000 Dig. Output Switch 1
DOutSw2 6001 Dig. Output Switch 2
DOutSw3 6002 Dig. Output Switch 3

ECU List – GEMS 2.3.0 Global Guide 35

 DOutSw4 6003 Dig. Output Switch 4
DOutSw5 6004 Dig. Output Switch 5
DOutSw6 6005 Dig. Output Switch 6
DOutSw7 6006 Dig. Output Switch 7
DOutSw8 6007 Dig. Output Switch 8
DOutSw9 6008 Dig. Output Switch 9
DOutSw10 6009 Dig. Output Switch 10

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
AUXTEMP1 - Aux. Temp 1
AUXTEMP2 - Aux. Temp 2
AUXTEMP3 - Aux. Temp 3
AUXTEMP4 - Aux. Temp 4
AUXTEMP5 - Aux. Temp 5
AUXTEMP6 - Aux. Temp 6
Eng Speed1 - Engine Speed 1
Eng Speed2 - Engine Speed 2
LAMBDA1 - Lambda 1
LAMBDA2 - Lambda 2
EGTMax - EGT max.
LoadContrPos - Load Control Pos.
LoadCtrllPos - Load Controller Pos.
LambdaCorr - Lambda Corrextion
TorqMeas - Torque measured
TorqCalc - Power measured
PowerMeas - Torque calc.
PowerCalc - Power calc.
InpAna1 - Input Analog 1
InpAna2 - Input Analog 2
InpAna3 - Input Analog 3
InpAna4 - Input Analog 4
InpAna5 - Input Analog 5
InpAna6 - Input Analog 6
InpAna7 - Input Analog 7
InpAna8 - Input Analog 8
InpAna9 - Input Analog 9
InpAna10 - Input Analog 10
InpAna11 - Input Analog 11
InpAna12 - Input Analog 12
InpAna13 - Input Analog 13
InpAna14 - Input Analog 14
InpAna15 - Input Analog 15
InpAna16 - Input Analog 16
InpAna17 - Input Analog 17
InpAna18 - Input Analog 18
InpAna19 - Input Analog 19
InpAna20 - Input Analog 20

ECU List – GEMS 2.3.0 Global Guide 36

 InpAna21 - Input Analog 21
InpAna22 - Input Analog 22
InpAna23 - Input Analog 23
InpAna24 - Input Analog 24
SetSpeed - Setpoint Speed
SpeedErr - Speed Error
TrError - Transient Error
AttStart - No. of Attempts to Start
SetBPress - Setpoint Boost Pressure
NoErr - No. of Error
SetLoad - Setpoint Load
ThrOut - Throttle Output
MixPos - Mixer Position
NoKnockA - No. Of Knockings Cyl. A
NoKnockB - No. Of Knockings Cyl. B
NoKnockC - No. Of Knockings Cyl. C
NoKnockD - No. Of Knockings Cyl. D
NoKnockE - No. Of Knockings Cyl. E
NoKnockF - No. Of Knockings Cyl. F
NoKnockG - No. Of Knockings Cyl. G
NoKnockH - No. Of Knockings Cyl. H
KnockDelA - Knocking Ign. Delay Cyl.A
KnockDelB - Knocking Ign. Delay Cyl.B
KnockDelC - Knocking Ign. Delay Cyl.C
KnockDelD - Knocking Ign. Delay Cyl.D
KnockDelE - Knocking Ign. Delay Cyl.E
KnockDelF - Knocking Ign. Delay Cyl.F
KnockDelG - Knocking Ign. Delay Cyl.G
KnockDelH - Knocking Ign. Delay Cyl.H
NoMisFirA - No. Of Misfiring Cyl A
NoMisFirB - No. Of Misfiring Cyl B
NoMisFirC - No. Of Misfiring Cyl C
NoMisFirD - No. Of Misfiring Cyl D
NoMisFirE - No. Of Misfiring Cyl E
NoMisFirF - No. Of Misfiring Cyl F
NoMisFirG - No. Of Misfiring Cyl G
NoMisFirH - No. Of Misfiring Cyl H
TorqueA - Torque Cyl. A
TorqueB - Torque Cyl. B
TorqueC - Torque Cyl. C
TorqueD - Torque Cyl. D
TorqueE - Torque Cyl. E
TorqueF - Torque Cyl. F
TorqueG - Torque Cyl. G
TorqueH - Torque Cyl. H
ThrottleVlv1 51 Engine Throttle Valve 1 Position 1
1,2,3,4,5,6,7,8
Load 92 Engine Percent Load At Current Speed
1,2,3,4,5,6,7,8
P-Oil 100 Engine Oil Pressure

ECU List – GEMS 2.3.0 Global Guide 37

 1,2,3,4,7,8
T-IntManifold 105 Engine Intake Manifold 1 Temperature
P-IntakeAir 106 Engine Intake Air Pressure
P-Barometric 108 Barometric Pressure
1,2,3,4,5,6,7,8
T-Coolant 110 Engine Coolant Temperature
Battery 168 Battery Potential / Power Input 1
1,2,3,4,5,6,7,8
EngineSpeed 190 Engine Speed
TorqueActual 513 Actual Engine - Percent Torque
T-ECU 1136 Engine ECU Temperature
Cyl 1IgnTiming 1413 Engine Cylinder 1 Ignition Timing
Cyl 2IgnTiming 1414 Engine Cylinder 2 Ignition Timing
Cyl 3IgnTiming 1415 Engine Cylinder 3 Ignition Timing
Cyl 4IgnTiming 1416 Engine Cylinder 4 Ignition Timing
Cyl 5IgnTiming 1417 Engine Cylinder 5 Ignition Timing
Cyl 6IgnTiming 1418 Engine Cylinder 6 Ignition Timing
Cyl 7IgnTiming 1419 Engine Cylinder 7 Ignition Timing
Cyl 8IgnTiming 1420 Engine Cylinder 8 Ignition Timing
T-Exh2Manf1 2433 Engine Exhaust Manifold Bank 2 Temperature 1
T-Exh1Manif1 2434 Engine Exhaust Manifold Bank 1 Temperature 1
SCR IntakeNOx 3216 Aftertreatment 1 SCR Intake NOx 1
SCR2IntakeNOx 3255 Aftertreatment 2 SCR Intake NOx 1
Operating 3543 Engine Operating State

ECU analog inputs (controller's outputs)

Configuration Name SPN J1939 Name
SetLoadCtrPos - SetLoad Controller Pos.
SetLbdaCorr - Set Lambda Correction
SetIgnCorr - Set Ignition Correction
PowerReq - Power Request
POWER - Actual Power
MixerSetAbs - Mixer Setpoint abs.
LambdaSetAbs* - Lambda Setpoint abs.
IgnAngleAbs - Ignition Angle abs.
MixerSetRel* - Mixer Setpoint rel.
LambdaSetRel* - Lambda Setpoint rel.
IgnAngleRel - Ignition Angle rel.
1,2,3,4,5,6,7,8
Spd-Requested 898 Engine Requested Speed/Speed Limit

*The parameter requires extended controller's support. Please refer controller's manual for further
information.

ECU List – GEMS 2.3.0 Global Guide 38

3.13 Uninox
0x51
0x52
ECU address:
0x56
0x57

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
AT1IntGSPwr 3218 Aftertreatment 1 Intake Gas Sensor 1 Power In Range
AT1IntGSTmp 3219 Aftertreatment 1 Intake Gas Sensor 1 at Temperature
SCR IntakeNOx 3220 Aftertreatment 1 SCR Intake NOx 1 Reading Stable
AT1IntWROxygen 3221 Aftertreatment 1 Intake Wide-Range Percent Oxygen 1 Reading Stable
AT1IntGSHeater 3223 Aftertreatment 1 Intake Gas Sensor 1 Heater Control
AT1OutGS1Pwr 3228 Aftertreatment 1 Outlet Gas Sensor 1 Power In Range
AT1OutGS1Tmp 3229 Aftertreatment 1 Outlet Gas Sensor 1 at Temperature
AT1OutNOxRead 3230 Aftertreatment 1 Outlet NOx 1 Reading Stable
AT1OutWROxygen 3231 Aftertreatment 1 Outlet Wide-Range Percent Oxygen 1 Reading Stable
AT1OutGS1Heat 3233 Aftertreatment 1 Outlet Gas Sensor 1 Heater Control
AT2IntGSPwr 3257 Aftertreatment 2 Intake Gas Sensor 1 Power In Range
AT2IntGSTmp 3258 Aftertreatment 2 Intake Gas Sensor 1 at Temperature
SCR2IntakeNOx 3259 Aftertreatment 2 SCR Intake NOx 1 Reading Stable
AT2IntWROxygen 3260 Aftertreatment 2 Intake Wide-Range Percent Oxygen 1 Reading Stable
AT2IntGSHeater 3262 Aftertreatment 2 Intake Gas Sensor 1 Heater Control
AT2OutGS1Pwr 3267 Aftertreatment 2 Outlet Gas Sensor 1 Power In Range
AT2OutGS1Tmp 3268 Aftertreatment 2 Outlet Gas Sensor 1 at Temperature
AT2OutNOxRead 3269 Aftertreatment 2 Outlet NOx 1 Reading Stable
AT2OutWROxy1 3270 Aftertreatment 2 Outlet Wide-Range Percent Oxygen 1 Reading Stable
AT2OutGS1Heat 3272 Aftertreatment 2 Outlet Gas Sensor 1 Heater Control

ECU binary inputs (controller's outputs - commands)

Configuration Name SPN J1939 Name
AT1IntDewPoint 3237 Aftertreatment 1 Intake Dew Point
AT1ExhDewPoint 3238 Aftertreatment 1 Exhaust Dew Point

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
SCR IntakeNOx 3216 Aftertreatment 1 SCR Intake NOx 1
AT1IntOxygen 3217 Aftertreatment 1 Intake Percent Oxygen 1
AT1IntGSHeater 3222 Aftertreatment 1 Intake Gas Sensor 1 Heater Preliminary FMI
SCR IntakeNOx 3224 Aftertreatment 1 SCR Intake NOx Sensor 1 Preliminary FMI
AT1IntOxygen 3225 Aftertreatment 1 Intake Oxygen Sensor 1 Preliminary FMI
AT1OutNOx 3226 Aftertreatment 1 Outlet NOx 1
AT1OutOxygen1 3227 Aftertreatment 1 Outlet Percent Oxygen 1
AT1OutGS1Heat 3232 Aftertreatment 1 Outlet Gas Sensor 1 Heater Preliminary FMI

ECU List – GEMS 2.3.0 Global Guide 39

 AT1OutNOxFMI 3234 Aftertreatment 1 Outlet NOx Sensor 1 Preliminary FMI
AT1OutOSFMI 3235 Aftertreatment 1 Outlet Oxygen Sensor 1 Preliminary FMI
SCR2IntakeNOx 3255 Aftertreatment 2 SCR Intake NOx 1
AT2IntOxygen 3256 Aftertreatment 2 Intake Percent Oxygen 1
AT2IntGSHeater 3261 Aftertreatment 2 Intake Gas Sensor 1 Heater Preliminary FMI
SCR2IntakeNOx 3263 Aftertreatment 2 SCR Intake NOx Sensor 1 Preliminary FMI
AT2IntOxygen 3264 Aftertreatment 2 Intake Oxygen Sensor 1 Preliminary FMI
AT2OutNOx 3265 Aftertreatment 2 Outlet NOx 1
AT2OutOxygen1 3266 Aftertreatment 2 Outlet Percent Oxygen 1
AT2OutGS1Heat 3271 Aftertreatment 2 Outlet Gas Sensor 1 Heater Preliminary FMI
AT2OutNOxFMI 3273 Aftertreatment 2 Outlet NOx Sensor 1 Preliminary FMI
AT1OutNOxHours 5721 Aftertreatment 1 Outlet NOx Sensor Operation Hours
AT1IntNOxHours 5722 Aftertreatment 1 Intake NOx Sensor Operation Hours
AT2OutNOxHours 5723 Aftertreatment 2 Outlet NOx Sensor Operation Hours
AT2IntNOxHours 5724 Aftertreatment 2 Intake NOx Sensor Operation Hours

ECU List – GEMS 2.3.0 Global Guide 40

3.14 Varistep 1
ECU address: 0x5A

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
Offline - Offline
Mode - Error
Man/Auto - Manual / Auto Mode
StepError - Step Error
Timeout - Time out error
LowPwr - Low power error
OverTemp - Over temperature error
OverCurr - Over Current Error
OpenPosition - Open position
ClosePosition - Close position

ECU binary inputs (controller's outputs - commands)

Configuration Name SPN J1939 Name
Reset - Reset
StepToClose - Step to close
StepToOpen - Step to open

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
CurrentPos - Current position in %
ExtTargetPos - External Target Position

ECU analog inputs (controller's outputs)

Configuration Name SPN J1939 Name
Opening - Opening in percent
Mode - Mode

ECU List – GEMS 2.3.0 Global Guide 41

3.15 Varistep 2
ECU address: 0x5B

Available parameters
ECU binary outputs (controller's inputs)
Configuration Name SPN J1939 Name
Offline - Offline
Mode - Error
Man/Auto - Manual / Auto Mode
StepError - Step Error
Timeout - Time out error
LowPwr - Low power error
OverTemp - Over temperature error
OverCurr - Over Current Error
OpenPosition - Open position
ClosePosition - Close position

ECU binary inputs (controller's outputs - commands)

Configuration Name SPN J1939 Name
Reset - Reset
StepToClose - Step to close
StepToOpen - Step to open

ECU analog outputs (controller's inputs)

Configuration Name SPN J1939 Name
CurrentPos - Current position in %
ExtTargetPos - External Target Position

ECU analog inputs (controller's outputs)

Configuration Name SPN J1939 Name
Opening - Opening in percent
Mode - Mode

ECU List – GEMS 2.3.0 Global Guide 42

4 Notes
6 back to Table of contents

4.1 Software compatibility

Version 2.3.0 can be imported into GenConfig, ECUDiag as a standard firmware package. It must be used
with the following versions of ComAp PC software:
InteliConfig ver. 2.28.0 or newer
DriveConfig ver. 4.0.1 or newer
GenConfig ver. 3.14.0 or newer
ECUDiag ver. 1.3 or newer

ECU List – GEMS 2.3.0 Global Guide 43