Service Manual

ViewSonic VA1716w
Model No VS11754
17” Color TFT LCD Display

Manufacture Date: Jun-19-07

-1–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Copyright Information
®
Copyright © ViewSonic Corporation, 2006. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of
Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS
and DDC are trademarks of VESA.
®
ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency
®
(EPA). As an ENERGY STAR partner, ViewSonic Corporation has determined that this
®
product meets the ENERGY STAR guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the
right to change product specifications without notice. Information in this document may
change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
®
Copyright © ViewSonic Corporation, 2006. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
®
any language or manual or otherwise, without the prior written permission of ViewSonic
Corporation.

Revision History

Revision Date Description of changes Approval

A00 Jun-19-07 Initial Release (T77HMRHMKNWVSNJ) YG.WANG

-2–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 TABLE OF CONTENTS

1. Precautions And Safety Notices 4

2. Specification 7

3. Front Panel Control And Indicators 9

4. Circuit Description 15

5. Adjustment Procedure 23

6. Troubleshooting Flow Chart 41

7. Recommended Spare Parts List 42

8. Exploded Diagram And Spare Parts List 52

9. Disassemble Process 54

10. Block Diagram 58

11. Schematic Diagram 59

12. PCB Layout Diagram 66

-3–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
1. Precautions And Safety Notices

1.1 SAFETY PRECAUTIONS

This monitor is manufactured and tested on a ground principle that a user’s safety comes
first. However, improper use or installation may cause damage to the monitor as well as
the user. Carefully go over the following WARNINGS before installing and keep this guide
handy.

WARNINGS
．This monitor should be operated only at the correct power sources indicated on the label
on the rear end of the monitor. If you’re unsure of the power supply in your residence,
consult you local dealer or power company.
．Use only the special power adapter that comes with this monitor for power input.
．Do not try to repair the monitor your self as it contains no user-serviceable parts. This
monitor should only be repaired by a qualified technician.
．Do not remove the monitor cabinet. There is high-voltage parts inside that may cause
electric shock to human bodies, even when the power cord is unplugged.
．Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
．Put your monitor only in a clean, dry environment. If it gets wet, unplug the power cable
immediately and consult your service technician.
．Always unplug the monitor before cleaning it .Clean the cabinet with a clean, dry cloth.
Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
．Keep the monitor away from magnetic objects, motors, TV sets, and transformer.
．Do not place heavy objects on the monitor or power cord.

1.2 PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety visual inspections
and the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltages, wattage, etc. Before replacing any of these
components read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may
create shock, fire ,or other hazards.

1.3 SERVICE NOTES

1. When replacing parts or circuit boards, clamp the lead wires around terminals before
soldering.
2. When replacing a high wattage resistor(more than 1W of metal oxide film resistor) in
circuit board, keep the resistor about 5mm away from circuit board.
3. Keep wires away from high voltage, high temperature components and sharp edges.
4. Keep wires in their original position so as to reduce interference.
5. Usage of this product please refer to also user’s manual.

-4–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
1.4 HANDING AND PLACING METHODS
Correct Methods: Incorrect Methods:
Only touch the metal frame of the LCD
Surface of the LCD panel is pressed by fingers
panel or the front cover of the monitor. Do
and that may cause “Mura.”
not touch the surface of the polarizer.

Taking out the monitor by grasping the LCD

Take out the monitor with cushions
panel. That may cause “Mura.”

Placing the monitor on foreign objects. That

Place the monitor on a clean and soft foam
could scratch the surface of the panel or cause
pad.
“Mura.”

-5–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Place the monitor on the lap, the panel The panel is placed facedown on the lap. That
surface must be upwards. may cause “Mura.”

-6–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
2. Specification
2.1 PRODUCT SPECIFICATIONS
LCD Type 17.0” (full 17” wide viewable diagonal area),
TFT(Thin Film Transistor), WXGA+
0255mm pixel pitch
Color Filter RGB vertical stripe
Glass Surface Anti-Glare
Input Signal Video Sync RGB analog(0.7/1.0 Vp-p, 75ohms)
Separate Sync,
Fh:30-82 kHz, Fv:50-75 Hz
Compatibility PC Up to 1440 x 900 Non-interlaced
Macintosh Power Macintosh up to 1440 x 900
Resolution Recommended 1440 x 900 @ 60 Hz
and supported 1280 x 1024 @ 60, 75 Hz
1024 x768 @ 60, 70, 72, 75 Hz
800 x 600 @ 56, 60, 72, 75 Hz
640 x 480 @ 60, 75 Hz
720 x 400 @ 70 Hz
Power Voltage 100V~240 VAC, 50/60Hz (auto switch)
367.2mm(H) x 229.5mm(V)
Display area Full Scan
14.45”(H) x 9.04”(V)
Temperature 41°F to + 95°F( 5°C to + 35°C)
Operating
Humidity 20%C to + 80%(non-condensing)
conditions
Altitude To 10,900 feet
Temperature -4°F to + 131°F( -20°C to + 55°C)
Storage
Humidity 20%C to + 85%(non-condensing)
conditions
Altitude To 40,000 feet
397.6mm(W) x 357.1mm(H) x195mm(D)
Dimensions Physical
15.6”(W) x 14.1”(H) x 7.7”(D)
Weight Physical 7.0 Ib(3.2 kg)
BSMI, CCC, PSB, C-Tick, CE, GS, MIC, VCCI,
Regulations Ergo, Gost-R/Hygienic, SASO, MPRII, Ukraine,
®
UL/cUL, FCC-B, ICES-B, NOM, TUV-S, Energy Star
Power saving On Normal (blue LED)
modes Off <1W (orange LED)
®
Preset Timing Mode (pre-adjusted to VESA 1440 x 900 @ 60 Hz)
Warning: Do not set the graphics card in your computer to exceed these refresh rates;
doing so may result in permanent damage to the LCD display.
1 ®
Macintosh computers older than G3 require a ViewSonic Macintosh adapter. To order an
adapter, contact ViewSonic.
-7–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
2.2 INTERFACE DESCRIPTION

D-SUB 15 PIN CONNECTOR

Pin Number Pin Function
1 Red video input
1 5
6 10 2 Green video input
11 15
3 Blue video input

4 No Connection

5 Ground

6 Red video ground

7 Green video ground

8 Blue video ground

9 +5V

10 H/V sync ground

11 No connection

12 (SDA)

13 Horizontal sync (Composite sync)

14 Vertical sync

15 (SCL)

SIGNAL LEVEL

-8–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
3. Front Panel Function Controls And Indicators

-9–
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Do the following to adjust the display setting:
1. To display the Main Menu, press button [1].

NOTE: All OSD menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to adjust, press ▲or ▼ to scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one
shown below appears.

The line at the bottom of the screen

shows the current functions of
buttons 1 and 2: Exit or select the
Brightness control.

4. To adjust the control, press the up ▲ or▼ down buttons.

5. To save the adjustments and exit the menu, press button [1] twice.

The following tips may help you optimize your display:

• Adjust the computer's graphics card so that it outputs a 1440 x 900 @ 60Hz video
signal to the LCD display. (Look for instructions on “changing the refresh rate” in the
graphics card's user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible. (The black border around the edge of the screen
should barely touch the illuminated “active area” of the LCD display.)

- 10 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Main Menu Controls
Adjust the menu items shown below by using the up and down buttons.

Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video
signal to eliminate waviness and distortion. Press the [2] button to obtain a
sharper image.
NOTE: Auto Image Adjust works with most common video cards. If this
function does not work on your LCD display, then lower the video refresh rate
to 60 Hz and set the resolution to its pre-set value.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).

Brightness adjusts background black level of the screen image.

Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).

sRGB-This is quickly becoming the industry standard for color management,

with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the intended. Enabling the sRGB setting
will cause Contrast and Brightness adjustments to be disabled.
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, press ▼ and ▲.
Important: If you select RECALL from the Main Menu when the product is
set to a Preset Timing Mode, colors return to the 6500K factory preset.

- 11 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
®
the ViewSonic website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1440 x 900 @ 60Hz (recommended) means that the resolution
is 1440 x 900 and the refresh rate is 60 Hertz.

Manual Image Adjust display the Manual Image Adjust menu

H./V. Position (Horizontal/Vertical Position) moves the screen image left or

right and up or down.

H./Size (Horizontal Size) adjusts the width of the screen image.

Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Setup Menu displays the menu shown below:

- 12 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Language Select allows the user to choose the language used in the menus
and control screens.

Resolution Notice advises the optimal resolution to use.

OSD Position allows the user to move the OSD menus and control screens.

OSD Timeout sets the length of time the OSD screen is displayed. For
example, with a “15 second” setting, if a control is not pushed within 15
seconds, the display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.

Memory Recall returns the adjustments back to factory settings if the display
is operating in a factory Preset Timing Mode listed in the Specifications of this
manual.

SHORT CUTS FUNCTION FROM THE BUTTONS

[1] Main Menu

[2] Auto Image Adjust

To immediately activate Brightness and menu. It should

[▼]
be change to Contrast OSD by push button[2]
To immediately activate Contrast menu. It should be
[▲]
change to Brightness OSD by push button[2]
[▲] DCR On/Off switching
(Keep pushing 3 sec.) Loop: DCR On <=> DCR Off
Recall both of Contrast and Brightness to default without
[▼] + [▲]
OSD message.
Toggle 720x400/70Hz and 640x400/70Hz mode when
input 720x400/70Hz or 640x400/70Hz mode
[1] + [2]
Toggle 640x400/60Hz and 640x480/60Hz mode when
input 640x400/60Hz or 640x480/60Hz mode

White Balance
1. It will not shown on user’s guide
[1] + [▼] + [▲] 2. OSD message as below,
(Keep pushing 5 sec)

(Image = no blanking)
Toggle DDC/CI and DDC/2B (DDC/CI enable/disable) and
[2] + [▼] show following message for 3 seconds,
(This function only in Dual input Model)

- 13 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 When switch to DDC/CI

When switch to DDC/2B

Default = DDC/CI
[1] + [▲] OSD Lock

[1] + [▼] Power Lock

[▲]+ [ ] + Main Power On All reset

No signal + [ ] + [1] Burning mode

signal + [ ] + [1] Factory Mode

Remark : All the short cuts function are only available while OSD off

- 14 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
4. Circuit Description
4.1 LCD MONITOR DESCRIPTION
The LCD MONITOR will contain a Main Board, an Power Board, Key Board which
house the flat panel control logic, brightness control logic and DDC.

Monitor Block Diagram

CCFL Drive. Flat Panel and

CCFL backlight

RS232 Connector
Power Board Main Board
For white balance
(Include: adapter, inverter)
adjustment in factory
mode

Video signal, DDC

Key Board

AC-IN HOST Computer

100V-240V

4.2 MAIN BOARD BLOCK FUNCTION DESCRIPTION

The main board contains panel control logic, brightness control logic, DDC and DC
convert DC circuit and so on.
PWPC board

R
G
B
H Backlight and Panel
V TSUM16AK
SDA
SCL

OSC
Keyboard
EPROM EPROM

- 15 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 4.3 PWPC BOARD BLOCK FUNCTION DESCRIPTION
PWPC board combines to adapter and inverter, Adapter which commonly consists
of bridge rectifier and filter, start circuit, PWM control circuit, protection circuits and
convert to 12V, 5V DC voltage by input 90V-240V AC voltage that provide power supply
for each chips in the main board and inverter. Inverter is DC TO AC circuit. It changes
the 12v DC of power supply to about 600-800v AC that drives the backlight. It mostly
consists of starting circuit, PWM controller, DC changing circuit, LC surging circuit,
output circuit and protection circuit etc.

Bridge Rectifier
AC input Transformer
EMI filter Rectifier CMOS
and Filter

Start Circuit
R904, R905,ZD901 CN902
5V

PWM Over 12V

Control IC Voltage
Protect
ON/OF
OSC and MOSFET
Output DC Convert
Circuit Q805
Circuit
Lamp
Feedback Over ON/OFF
Circuit Voltage PWM Control
Control IC

DIM

- 16 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 4.4 INTRODUCTION OF IC
TSUM16AWR-LF-1(U401): integrate ADC, OSD, SCALER, MCU, LVDS, convert analog
RGB into digital and room and shrink scaling output to LCD panel.
PIN Function:
Pin Symbol Description
21 SDO SPI flash serial data output; Input w/5V-tolerant
22 CSZ SPI flash chip select; output
23 SCK SPI flash serial select; output
24 SDI SPI flash serial data input; output
18 DDCA_SDA/RS232_TX DDC data for analog interface; 4mA driving
strength/UART transmitter/GPIO; I/O w/5V-tolrant
19 DDCA_SCL/RS232_RX DDC data for analog interface/UART
transmitter/GPIO; Input w/5V-tolrant
54 RST Chip reset; High reset; Input w/5V-tolerant
57 RSTN Chip reset; Low reset; Input w/5W-toerant
52 VCTRL Regulator control; Output
16 HSYNCO Analog HSYNC input
17 VSYNCO Analog VSYNC input
15 REFP Internal ADC top de-coupling pin
14 REFM Internal ADC bottom de-coupling pin
4 REXT External resistor 390 ohm to AVDD
32、31 MODE[1：0] Input Chip Configuration Input
MODE[1:0] Chip Operation
00 Normal Opertaion
1 XIN Xin; Crystal Oscillator Input
2 XOUT Xout; Crystal Oscillator Output
6 AVDD＿ADC ADC Power 3.3V
51 VDDP Digital Output Power 3.3V
30、53 VDDC Digital Core Power 1.8V
3、5、29 GND Ground

AP1117E33LA(U701): DC power convert, convert to 3.3v.

AIC1117A-18PY(U702): DC power convert, convert to 1.8v.

SST25LF020A-33-4C-SAE(U203): SST’s serial flash family features a four-wire,

SPI-com-patible interface that allows for a low pin-count package occupying less board
space and ultimately lowering total system costs. The SST25LF020A/040A devices
significantly improve performance, while lowering power consumption. The total energy
consumed is a function of the applied voltage, current, and time of application. The
SST25LF020A/040A devices operate with a single 3.0-3.6V power supply. The
SST25LF020A devices are offered in an 8-lead SOIC 150 mil body width (SA) package.

- 17 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Pin Diagram:

PIN Descriptions:

Symbol Pin Name Functions

To provide the timing of the serial interface.

Commands, addresses, or input data are latched on the
SCK Serial Clock
rising edge of the clock input, while output data is shifted out
on the falling edge of the clock input.

Serial Data To transfer commands, addresses, or data serially into the

SI device.
Input Inputs are latched on the rising edge of the serial clock.

Serial Data To transfer data serially out of the device.

SO
Output Data is shifted out on the falling edge of the serial clock.

The device is enabled by a high to low transition on CE#.

CE# Chip Enable CE# must remain low for the duration of any command
sequence.

The Write Protect (WP#) pin is used to enable/disable BPL

WP# Write Protect
bit in the status register.
To temporarily stop serial communication with SPI flash
HOLD# Hold
memory without resetting the device.

VDD Power Supply To provide power supply(3.0-3.6V)

VSS Ground

- 18 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Circuit Diagram

LD7552BPS (IC901): PWM control, high-voltage startup current. The circuit unit has
functions such as over-current protection, over-voltage protection, output short-circuit
protection and etc. The function of each pin and the inside circuit diagram are as
follows:
Pin Name Function
1 GND Ground
Voltage feedback pin (same as the COMP pin in UC384X), By
2 COMP connecting a photo-coupler to close the control loop and achieve the
regulation
3 VCC Supply voltage pin
This pin is to program the switching frequency. By connecting a resistor
4 RT
to ground to set the switching frequency.
6 NC Unconnected pin
7 VCC Supply voltage pin
8 OUT Gate drive output to drive the external MOSFET

- 19 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 OZ9938GN(IC801): The OZ9938 is high performance, cost-effective CCFL controller
designed for driving large-size LCD applications requiring 2 to 6 CCFLs.PWM
control, Has such functions as short-voltage protection, Over-voltage protection,
over-current protection and etc. The function of each pin and the circuit diagram
inside are as follows:
PIN Descriptions:
Pin Names Description
1 DRV1 Drive output
2 VDDA Supply voltage input
3 TIMER Timing capacitor to set striking time and shutdown delay time
Analog dimming or Internal LPWM dimming or external PWM pulse
4 DIM
input for dimming function
5 ISEN Current sense feedback
6 VSEN Voltage sense feedback

- 20 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 7 OVPT Over-voltage/ over-current protection threshold setting pin
8 NC No connection
9 NC No connection
10 ENA ON/OFF control of IC
Timing capacitor to set internal PWM dimming frequency and also a
11 LCT
pin for analog dimming selection
12 SSECMP Capacitor for soft start time and loop compensation
13 CT Timing resistor and capacitor for operation and striking frequency
14 GNDA Ground for analog signals
15 DRV2 Drive output
16 PGND Ground for power paths

- 21 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Block Diagram

- 22 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
5. Adjustment Procedure
5.1 ADJUSTMENT CONDITIONS AND PRECAUTIONS
1. Approximately 30 minutes should be allowed for warm up before proceeding.
2. Adjustments should be undertaken only on those necessary elements since most of them
have been carefully preset at the factory.
3. ESD protection is needed before adjustment.
5.2 MAIN ADJUSTMENTS
NO. FUNCTIONS DESIGNATION
1. White Balance Function Key
2. Geometry Function Key
5.3 ALIGNMENT PROCEDURES
Approximately 30 minutes should be allowed for warm up before proceeding
White-Balance adjustment.

1. Adjust of White Balance

1.) How to do the CA-210 MEM .Channel setting

A、Reference to CA-210 user guide
B、Use “ MODE” key to modify x、y、Lv value and use “MEMORY CH” key to modify the
TEXT description Following is the procedure to do white-balance adjust

2.) Setting the color temp. You want

A、MEM.CHANNEL1 ( 9300 color):
9300 color temp. parameter is x = 0.283 ±0.003; y = 0.298 ±0.003;
Lv ≥ 160 cd/m2 ,
B、MEM.CHANNEL1 ( 6500 color):
6500 color temp. parameter is x = 0.313±0.003; y = 0.329 ±0.003;
Lv ≥ 190 cd/m2,
C、MEM.CHANNEL 1 ( 5400 color):
5400 color temp. parameter is x = 0.335±0.003; y = 0.350 ±0.003;
Lv ≥ 190 cd/m2,
D、MEM.CHANNEL1 ( SRGB color):
SRGB color temp. parameter is x=0.313±0.003; y=0.329±0.003; Lv≥190cd/m2,
3.) Into factory mode of VA1716wmb
First Power off, then press Switch 1 button along with press Power button will activate
the factory mode, then MCU will do AUTO LEVEL automatically. Meanwhile press
MENU the OSD screen will located at LEFT TOP OF PANEL.

4.) Bias adjustment :

Set the Contrast to 70，Adjust the Brightness to 100.

- 23 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
5.) Gain adjustment :
Move cursor to “-F-” and press MENU key

A、Adjust 9300 color-temperature

(1)、Switch the CA-210 to x、y、Lv -Mode (with press “MODE” button )
(2)、Switch the MEM. channel to Channel 1 ( with up or down arrow on CA-210 )
(3) 、 The LCD-indicator on CA-210 will show x=0.283±0.003, y=0.298±0.003,
Lv≥160cd/m2
(4) Adjust the R G B of color3 on factory window until CA210 indicator reached
x=0.283±0.003, y=0.298±0.003, Lv≥160cd/m2
B、Adjust 6500 color-temperature
(1)、Switch the CA-210 to x、y、Lv -Mode (with press “MODE” button )
(2)、Switch the MEM .channel to Channel 1 ( with up or down arrow on CA-210 )
(3) 、 The LCD-indicator on CA-210 will show x=0.313±0.003, y=0.329±0.003,
Lv≥190 cd/m2
(4) Adjust the R G B of color3 on factory window until CA210 indicator reached
x=0.313±0.003, y=0.329±0.003, Lv≥190 cd/m2
C、Adjust 5400 color-temperature
(1)、Switch the CA-210 to x、y、Lv -Mode (with press “MODE” button )
(2)、Switch the MEM .channel to Channel 1( with up or down arrow on CA-210 )
(3) 、 The LCD-indicator on CA-210 will show x=0.335±0.003, y=0.350±0.003,
Lv≥190 cd/m2
(4)、Adjust the R G B of color3 on factory window until CA210 indicator reached
x = 0.335±0.003; y = 0.350 ±0.003; Lv≥190 cd/m2
D、Adjust SRGB color-temperature
(1)、Switch the CA-210 to x、y、Lv -Mode (with press “MODE” button )
(2)、Switch the MEM .channel to Channel 1 ( with up or down arrow on CA-210 )
(3) 、 The LCD-indicator on CA-210 will show x=0.313±0.003, y=0.329±0.003,
Lv≥190 cd/m2
(4)、Adjust the R G B of color3 on factory window until CA210 indicator reached
x=0.313±0.003, y=0.329±0.003, Lv≥190 cd/m2
E、Press reset key and Turn the Power-button “off to on” to quit from factory mode。

2. Geometry
1).Set cross-hatch pattern and preset timing as timing table listed.
2).Change to each mode in turn and wait for the monitor finish auto-alignment and save
press before change to next mode.
3).Until all of modes are adjusted, exit OSD menu and press POWER OFF to exit factory
mode.

- 24 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
5.4 Factory Defaults
Item Defaults Item Defaults
Contrast 70% Input Priority N/A
Brightness 100% Resolution Notice On
Color Temperature 6500K Volume N/A
Sharpness 100% Balance N/A
OSD H. Position 50% Treble N/A
OSD V. Position 50% Bass N/A
OSD Time Out 15 720x400 / 640x400 720x400
OSD Background On 640x480 / 640x400 640x480

5.5 Function Test

1 Product: 17” LCD Monitor
2 Test Equipment: Color Video Signal & Pattern (or PC with SXGA resolution and a
sound card)
3 Test Condition: Before function test and alignment, each LCD Monitor should be
warmed up for at least 30 minutes with the following conditions:
(a)In room temperature,
(b) With full-white screen, RGB, and Black
(c) With cycled display modes,
640*480 (H=43.27kHz, V=75Hz)
800*600 (H=53.7kHz, V=75Hz)
1024*768 (H=68.67kHz, V=75Hz)
1280*1024 (H=79.97kHz, V=75Hz)
1440*900 (H=55.9kHz, V=60Hz)
4 Test Display Modes & Pattern
Compatible Modes
Item Timing Analog
1 640 x 480 @ 60Hz, 31.5kHz Yes
2 640 x 480 @ 75Hz, 31.5kHz Yes
3 720 x 400 @ 70Hz, 31.5kHz Yes
4 800 x 600 @ 56Hz, 35.1kHz Yes
5 800 x 600 @ 60Hz, 37.9kHz Yes
6 800 x 600 @ 72Hz, 48.1kHz Yes
7 800 x 600 @ 75Hz, 46.9kHz Yes
8 1024 x 768 @ 60Hz, 48.4kHz Yes
9 1024 x 768 @ 70Hz, 56.5kHz Yes
10 1024 x 768 @ 72Hz, 58.1kHz Yes
11 1024 x 768 @ 75Hz, 60.0kHz Yes
12 1280 x 1024 @ 60Hz, 48.4kHz Yes
13 1280 x 1024 @ 75Hz, 60.0kHz Yes
14 1440 x 900 @ 60Hz, 55.9kHz Yes

- 25 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Function Test Display Pattern
Item Test Content Pattern Specification Remark
Frequency & Eliminate visual wavy
1 Fine Line Moire Figure 1
Tracking noise.
Contrast/Bright 16 gray levels sh should
2 16 Gray Scale Figure 2
ness be distinguishable.
Horizontal and Vertical
Horizontal & Vertical position of video should
3 Boundary Figure 3
Thickness be adjustable to be
within the screen frame.
Contrast of each R, G,
RGB Color Figure
4 RGB Color Intensities B, color should be
Performance 4,5,6
normal.
Screen
Should be compliant
5 Uniformity & Full White Figure 7
with the spec.
Flicker
The numbers of dead
Dead White Screen & Dark
6 pixels should be Figure 7,8
Pixel/Line Screen
compliant with the spec.
The screen must have
7 White Balance White & Black Pattern the pure white and black Figure 9
pattern, no other color.

Fine Line Morie Pattern (Figure1) Gray Scale Pattern (Figure2)

- 26 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Horizontal & Vertical Thickness Pattern R. Color Pattern (Figure 4)
(Figure 3)

G. Color Pattern (Figure 5) B. Color Pattern (Figure 6)

Full White Pattern (Figure 7) Dark Screen Pattern (Figure 8)

Black-White Pattern (Figure 9)

- 27 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 4.3 Function Test and Alignment Procedure
All Modes Reset
You should do “All Mode Reset” (Refer to Chapter III-3. Hot Keys for Function
Controls) first. This action will allow you to erase all end-user’s settings and restore
the factory defaults.
Auto Image Adjust
Please select and enter “Auto Image Adjust” function on Main Menu to see if it is
workable. The “Auto Image Adjust” function is aimed to offer a better screen quality
by built-in ASIC. For optimum screen quality, the user has to adjust each function
manually.
Firmware
Test Pattern: Burn In Mode (Refer to Chapter III-3. Hot Keys for Function Controls)
- Make sure the F/W is the latest version.
DDC
Test Pattern: EDID program
Make sure it can pass test program.
Fine Tune and Sharpness
Test Signal: 1440*900@60Hz
Test Pattern: Line Moire Pattern
Check and see if the image has noise and focus performs well. Eliminate visual
line bar.
If not, readjust by the following steps:
(a)Select and enter “Fine Tune” function on “Manual Image Adjust” to adjust the
image to eliminate visual wavy noise.
(b)Then, select and enter “Sharpness” function to adjust the clarity and focus of
the screen image.
Boundary
Test Signal: 1440*900@60Hz
Test Pattern: Horizontal & Vertical Line Thickness Pattern
Check and see if the image boundary is within the screen frame.
If not, readjust by the following steps:
(a)Select and enter “Manual Image Adjust” function on OSD Main Menu.
(b)Then, select and enter “Horizontal Size” or “Horizontal/Vertical Position” function
to adjust the video boundary to be full scanned and within screen frame.
White Balance
Test Signal: 1440*900@60Hz
Test Pattern: White and Black Pattern
1.5.8 R, G, B, Colors Contrast
Test Signal: 1440*900@60Hz
Test Pattern: R, G, B, Color Intensities Pattern and 16 Gray Scale Pattern
- Check and see if each color is normal and distinguishable.
- If not, please return the unit to repair area.
Screen Uniformity and Flicker
Test Signal: 1440*900@60Hz
Test Pattern: Full White Pattern
- Check and see if it is in normal condition.
1.5.10 Dead Pixel and Line
- 28 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Test Signal: 1440*900@60Hz
Test Pattern: Dark and White Screen Pattern
- Check and see if there are dead pixels on LCD panel with shadow gauge and
filter film.
- The total numbers and distance of dead pixels should be compliant with the
spec.
Mura
Test Pattern: White, RGB, Black, & Grey
Test Tool: 10% ND Filter
- Check if the Mura can pass 10% ND Filter.
Audio
Test Signal: Voice signal (optional, depend on model)
Test Pattern: liberty
- Make sure there is audio output.
- Make sure that audio function (volume 80%) is working without noise and
resonance.
- Make sure that the sound of right and left speakers are in balance.
Check for Secondary Display Modes
Test Signal:
Analog: 640*480@60/75Hz;
720*400@70Hz; 800*600@56/60/72/75Hz;
1024*768@60/70/72/75Hz; 1280*1024@60/75Hz
1440*900@60Hz
- Normally when the primary mode 1440*900@60Hz is well adjusted and
compliant with the specification, the secondary display modes will also be
compliant with the spec. But we still have to check with the general test pattern to
make sure every secondary is compliant with the specification.
All Modes Reset
After final QC step, we have to erase all saved changes again and restore the
factory defaults. You should do “All Mode Reset” again.
Power Off Monitor
Turn off the monitor by pressing “Power” button.

5.6 Firmware Upgrade Procedure

When you receive the returned monitor, please check whether the firmware version is
the latest. If not, please do the following procedures to upgrade it to the latest version.
1 Equipment Needed
- Monitor( TSUM Series )
- Fixture for Firmware Upgrade
- Power Adapter (P/N: 47.58201.001) *1 for Fixture
- VGA Cable (P/N: 42.59901.003) *1(Pin 4, 11 should be connected to GND)
- PC (Personal Computer)
- LPT Cable (P/N: 42.59906.001) *1
- Firmware Upgrade Program
- One additional monitor for checking the program execution
- 29 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 2 Setup Procedure
2.1 Connect P2 of Fixture with printer port of PC by LPT Cable.
2.2 Connect P1 of Fixture with Monitor(TSUM series) by VGA Cable.
2.3 Plug Power Adapter to Fixture.
2.4 Connect Power Cord to Monitor(TSUM series).
2.5 Connect P3 to the Signal Generator (eg.Chroma2326) for verifying it after the
operation being completed.
2.6 Connect PC to the additional monitor.

- 30 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
JP1：to Power Adapter

P1：to VGA Cable

P3：to Signal Generator

P2：to LPT Cable

3 Firmware Upgrade Procedure

Step 1. Let Monitor(TSUM series) set to be connected with AC cable and VGA cable.

Step 2.Execute the MSstar ISP tool.

Step 3. Click “Device” button . Make sure that parameters relative to WP# is followed
bellow.

- 31 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Step 4. Click “Read” button. Select the object bincode on your corresponding directory.

Step 5. Click “Auto” button. Be sure that function of Erase Device (File Area), Blank,
Program and Verify is selected, then execute the flashing action by clicking the “Run”
button.

- 32 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Step 6. If the flashing F/W has been completed, “Verify Ok” message will be shown on
the right TextBox and Flash Status will be “8C” in the right-bottom of window.

Step 7. Unplug and replug power cord of Monitor(TSUM series) set and then check the
OSD operation and image on srceen.

Step 8. At last, do “Memory Recall.”

- 33 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 3.2 Setup Procedure
3.2.1 Connect P2 and monitor of Fixture with VGA ports of Monitor (TSUM Series) by
VGA Cable.
3.2.2 Connect P1 of Fixture with Printer port of PC by LPT Cable.
3.2.3 Plug Power Adapter to Fixture.
3.2.4 Connect Power Cord to Monitor (TSUM Series).
3.2.5 Connect PC to the additional monitor.

JP1： Power Adapter

P2： VGA Cable

P1：to LTP Cable

3.3 DDC Key In Procedure

Sep1.Select and execute DDC Key In program

- 34 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 - 35 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Sep2:Inpute the S/N and execute “Enter”

- 36 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 - 37 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Sep3:Key the “Enter” and write the data

- 38 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 Sep4:If ddc program OK and show “data compare ok”

- 39 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
5.7 Packing Procedure

- 40 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
6. Troubleshooting Flow Chart

- 41 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
7. Recommended Spare Part List
VA1716W-2 BOM list——T77HMRMKNWVSNJ
ViewSonic Universal
Item Ref. P/N Description Location Q'ty
P/N number#
1
2 CBPC7HMRVSQ1 MAIN BOARD 1
3 KEPC7QB9 KEY BOARD 1
4 PWPC721HV3J POWER BOARD 1
5 23G3178709 3A VSC17-LCD FRONT LOGO 1
6 23G3178709 4A VSC17-LCD FRONT LOGO 1
7 40G 45760819A MODEL LABEL 1
8 40G 459709 1B CARTON LABEL 1
9 40G 459709 4A H/V WARNING LABEL 1
10 40G 459709 5A HI-POT LABEL FOR 17-LCD 1
11 40G 58162435A MANUAL P/N LABEL 1
12 40G581B709 4A S/N LABEL 2
13 45G 77 3 TRANSPARENT SHEET 173
14 52G 1150 C BLACK TAPE 8
15 52G 1185 24 VSC YELLOW TAPE 65
16 52G 1186 SMALL TAPE 8
17 52G 1211 A ALUMINUM TAPE 1
18 52G6019 1 YELLOW TAPE 12
19 52G6022 20 SMALL TAPE 100
20 89G 728HAA902 SIGNAL CABLE 1
21 89G402A18N LS POWER CORD 1
22 95G8018 3D654 LVDS CABLE 30P-24P 120MM 1
23 M1G 130 6120 SCREW XN01A 4
24 M1G 940 8 47 CR3 SCREW XN01A 2
25 M1G1140 6120 SCREW XN01A 1
26 M1G1730 6120 M3*6 XN01A 4
27 M1G1730 6120 M3*6 XN01B 1
28 M1G1740 10 47 CR3 SCREW XN01A 4
29 Q1G 330 10 47 CR3 SCREW XN01A 1
30 Q1G 930 8120 SCREW XN01A 1
31 Q1G1040 8120 SCREW XN01A 3
32 750GLH70GW112N000V PANEL HSD170MGW1-A00 HSD 1
33 A33G0216 Q1 B BUTTON 1
34 A33G0217 1 led-lens_va1720w 1
35 A33G0218 KR 1B HINGE COVER 1
36 A33G0246 KR 1B CABLE CLIP 2
37 A34G0364AKR 1B BEZEL 1
- 42 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 38 A34G0365 KR 1B REAR COVER 1
39 A34G0366 Q1 1B BUTTON COVER 1
40 A34G0367 KR 1B BASE 1
41 A34G0368 KR 1B STAND 1
42 J12G 394800 FOOT 6
43 J12G 808 1 VESA RUBBER 4
44 J15G1720 1 MAIN FRAME 1
45 J37G0070 1 HINGE 1
46 J40G 17T7096TA ID VA1716W 1
47 J40GSTAR709 1A EPA LABEL 1
48 J41G780170918A SELL USA CARD 1
49 J41G780170919B INSERT CARD 1
50 J41G780270910A QSG 1
51 J41G780270911A VISTA CARD 1
52 J44G7015 1 EPS 1
53 J44G7015 2 EPS 1
54 J44G7015709 1A CARTON 1
55 J45G 76 28V3A PE BAG FOR MANUAL-CARD 1
56 J45G 88606 R PE BAG FOR BASE 1
57 J45G 88607 R PE BAG FOR MONITOR 1
58 J50G 600 5 HANDLE 1 1
59 J50G 600 6 HANDLE 2 1
60 J52G6020VSC 2 PROTECT FILM 1
61 J70G170170926A CD MANUAL 1
62 33G3802 6 WAFER&PLUG CN201 1
63 33G3802 9 WAFER 2.0MM 9P CN401 1
64 33G8027 24 H PIN 24P 2.0MM RIGHT ANGL CN301 1
1.0
65 40G 45762412B CBPC LABEL
5
66 61G152M339 64 3.3OHM 5% 2W MINI R402 1
67 67G305V101 3 100UF +-2 16V C303 1
68 67G305V101 3 100UF +-2 16V C402 1
69 67G305V101 3 100UF +-2 16V C403 1
70 67G305V101 3 100UF +-2 16V C407 1
71 67G305V101 3 100UF +-2 16V C408 1
72 67G305V479 3P 4.7UF 16V +-20% 105 C220 1
73 88G 35315F H D-SUB 15PIN CN101 1
74 93G 22 53 CRYSTAL 14.31818MHZ HC-4 X201 1
75 56G 562548 IC TSUM16AWR-LF-1 MSTAR U401 1
76 56G 563 27 IC AIC1117A-18PY SOT-223 U702 1

- 43 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 77 56G 585 4A IC AP1117E33LA U701 1
78 56G1133 34 IC M24C02-WMN6TP U703 1
79 56G1133 81 SST25LF020A-33-4C-SAE SO U203 1
80 57G 417 6 PMBS3906 PNP Q202 1
81 57G 417 6 PMBS3906 PNP Q203 1
82 57G 417 6 PMBS3906 PNP Q301 1
83 57G 417 12 T 2N3904S-RTK/PS SOT-23 Q403 1
84 57G 417 12 T 2N3904S-RTK/PS SOT-23 Q406 1
85 57G 763 1 AO3401L Q302 1
86 61G0402000 RST CHIP JUMP MAX 0R05 1 R101 1
87 61G0402000 RST CHIP JUMP MAX 0R05 1 R201 1
88 61G0402101 RST CHIP 100R 1/16W 5% R102 1
89 61G0402101 RST CHIP 100R 1/16W 5% R103 1
90 61G0402101 RST CHIP 100R 1/16W 5% R104 1
91 61G0402101 RST CHIP 100R 1/16W 5% R108 1
92 61G0402101 RST CHIP 100R 1/16W 5% R110 1
93 61G0402101 RST CHIP 100R 1/16W 5% R111 1
94 61G0402101 RST CHIP 100R 1/16W 5% R113 1
95 61G0402101 RST CHIP 100R 1/16W 5% R114 1
96 61G0402101 RST CHIP 100R 1/16W 5% R115 1
97 61G0402101 RST CHIP 100R 1/16W 5% R117 1
98 61G0402101 RST CHIP 100R 1/16W 5% R207 1
99 61G0402101 RST CHIP 100R 1/16W 5% R212 1
100 61G0402101 RST CHIP 100R 1/16W 5% R213 1
101 61G0402101 RST CHIP 100R 1/16W 5% R214 1
102 61G0402101 RST CHIP 100R 1/16W 5% R215 1
103 61G0402101 RST CHIP 100R 1/16W 5% R222 1
104 61G0402101 RST CHIP 100R 1/16W 5% R230 1
105 61G0402102 RST CHIP 1K 1/16W 5% R406 1
106 61G0402103 RST CHIP 10K 1/16W 5% R137 1
107 61G0402103 RST CHIP 10K 1/16W 5% R205 1
108 61G0402103 RST CHIP 10K 1/16W 5% R209 1
109 61G0402103 RST CHIP 10K 1/16W 5% R210 1
110 61G0402103 RST CHIP 10K 1/16W 5% R211 1
111 61G0402103 RST CHIP 10K 1/16W 5% R223 1
112 61G0402103 RST CHIP 10K 1/16W 5% R226 1
113 61G0402103 RST CHIP 10K 1/16W 5% R227 1
114 61G0402103 RST CHIP 10K 1/16W 5% R232 1
115 61G0402103 RST CHIP 10K 1/16W 5% R301 1
116 61G0402103 RST CHIP 10K 1/16W 5% R401 1

- 44 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
117 61G0402103 RST CHIP 10K 1/16W 5% R403 1
118 61G0402103 RST CHIP 10K 1/16W 5% R413 1
119 61G0402103 RST CHIP 10K 1/16W 5% R414 1
120 61G0402104 RST CHIP 100K 1/16W 5% R219 1
121 61G0402104 RST CHIP 100K 1/16W 5% R304 1
122 61G0402200 RST CHIP 20R 1/16W 5% R216 1
123 61G0402202 RST CHIP 2K 1/16W 5% R105 1
124 61G0402202 RST CHIP 2K 1/16W 5% R106 1
125 61G0402390 0F RST CHIP 390R 1/16W 1% R109 1
126 61G0402390 0F RST CHIP 390R 1/16W 1% R204 1
127 61G0402390 1F RST CHIP 3.9K 1/16W 1% R228 1
128 61G0402390 1F RST CHIP 3.9K 1/16W 1% R229 1
129 61G0402472 RST CHIP 4K7 1/16W 5% R120 1
130 61G0402472 RST CHIP 4K7 1/16W 5% R121 1
131 61G0402472 RST CHIP 4K7 1/16W 5% R217 1
132 61G0402472 RST CHIP 4K7 1/16W 5% R218 1
133 61G0402472 RST CHIP 4K7 1/16W 5% R303 1
134 61G0402472 RST CHIP 4K7 1/16W 5% R404 1
135 61G0402682 RST CHIP 6K8 1/16W 5% R208 1
136 61G0402750 RST CHIP 75R 1/16W 5% R107 1
137 61G0402750 RST CHIP 75R 1/16W 5% R112 1
138 61G0402750 RST CHIP 75R 1/16W 5% R116 1
139 61G0805331 RST CHIP 330R 1/8W 5% R302 1
140 65G0402104 15 MLCC 0402 CAP 0.1UF K C112 1
141 65G0402104 15 MLCC 0402 CAP 0.1UF K C114 1
142 65G0402104 15 MLCC 0402 CAP 0.1UF K C115 1
143 65G0402104 15 MLCC 0402 CAP 0.1UF K C116 1
144 65G0402104 15 MLCC 0402 CAP 0.1UF K C201 1
145 65G0402104 15 MLCC 0402 CAP 0.1UF K C203 1
146 65G0402104 15 MLCC 0402 CAP 0.1UF K C207 1
147 65G0402104 15 MLCC 0402 CAP 0.1UF K C211 1
148 65G0402104 15 MLCC 0402 CAP 0.1UF K C212 1
149 65G0402104 15 MLCC 0402 CAP 0.1UF K C219 1
150 65G0402104 15 MLCC 0402 CAP 0.1UF K C225 1
151 65G0402104 15 MLCC 0402 CAP 0.1UF K C226 1
152 65G0402104 15 MLCC 0402 CAP 0.1UF K C227 1
153 65G0402104 15 MLCC 0402 CAP 0.1UF K C228 1
154 65G0402104 15 MLCC 0402 CAP 0.1UF K C229 1
155 65G0402104 15 MLCC 0402 CAP 0.1UF K C301 1
156 65G0402104 15 MLCC 0402 CAP 0.1UF K C302 1

- 45 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
157 65G0402104 15 MLCC 0402 CAP 0.1UF K C401 1
158 65G0402104 15 MLCC 0402 CAP 0.1UF K C409 1
159 65G0402104 15 MLCC 0402 CAP 0.1UF K C412 1
160 65G0402104 15 MLCC 0402 CAP 0.1UF K C413 1
161 65G0402104 15 MLCC 0402 CAP 0.1UF K C415 1
162 65G0402220 31 CHIP 22pF 50V NPO C102 1
163 65G0402220 31 CHIP 22pF 50V NPO C103 1
164 65G0402220 31 CHIP 22pF 50V NPO C221 1
165 65G0402220 31 CHIP 22pF 50V NPO C222 1
166 65G0402224 17 CHIP 0.22UF 16V Y5V C218 1
167 65G0402473 12 CHIP 0.047UF 16V X7R C101 1
168 65G0402473 12 CHIP 0.047UF 16V X7R C105 1
169 65G0402473 12 CHIP 0.047UF 16V X7R C106 1
170 65G0402473 12 CHIP 0.047UF 16V X7R C107 1
171 65G0402473 12 CHIP 0.047UF 16V X7R C109 1
172 65G0402473 12 CHIP 0.047UF 16V X7R C110 1
173 65G0402473 12 CHIP 0.047UF 16V X7R C113 1
174 65G0402509 31 CHIP 5pF 50V NPO C104 1
175 65G0402509 31 CHIP 5pF 50V NPO C108 1
176 65G0402509 31 CHIP 5pF 50V NPO C111 1
177 65G0603104 32 CHIP 0.1UF 50V X7R C414 1
178 71G 56K121 M GP CHIP BEAD 120OHM T FB301 1
179 71G 56Z601 2.0X1.2 100M=600OHM FB203 1
180 71G 59K190 B CHIP BEAD FB101 1
181 71G 59K190 B CHIP BEAD FB102 1
182 71G 59K190 B CHIP BEAD FB103 1
183 93G 60505 BAT54C DIODE D106 1
184 93G 64 33 BAV99 SOT-23 D102 1
185 93G 64 33 BAV99 SOT-23 D103 1
186 93G 64 33 BAV99 SOT-23 D104 1
187 93G 64 42 PP DIODE BAV70 SOT-23 D105 1
188 93G 39S 34 T ZENER DIODE UDZS5.6B ZD101 1
189 93G 39S 34 T ZENER DIODE UDZS5.6B ZD102 1
190 93G 39S 34 T ZENER DIODE UDZS5.6B ZD103 1
191 93G 39S 34 T ZENER DIODE UDZS5.6B ZD104 1
192 93G 39S 34 T ZENER DIODE UDZS5.6B ZD105 1
193 93G 39S 34 T ZENER DIODE UDZS5.6B ZD106 1
194 715G2632 1 MAIN BOARD PCB 1
195 77G 603 2C TO TACT SWITCH SW001 1
196 77G 603 2C TO TACT SWITCH SW002 1

- 46 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
197 77G 603 2C TO TACT SWITCH SW004 1
198 77G 603 2C TO TACT SWITCH SW005 1
199 95G8014 6648 W WIRE HARNESS CN001 1
200 61G0603200 1F RST CHIPR 2 KOHM +-1% 1/ R003 1
201 61G0603200 1F RST CHIPR 2 KOHM +-1% 1/ R004 1
202 61G0603300 1F RST CHIP 3K 1/10W 1% R001 1
203 61G0603300 1F RST CHIP 3K 1/10W 1% R002 1
204 77G 610OB6 TO TACT SWITCH 2PIN+LED 4PI SW003 1
205 715G2622 1 KEPC BOARD PCB 1
206 S80GL15T32V TRANSFORMER ASS'Y T901 1
207 S80GL19T18V TRANSFORMER ASS'Y PT801 1
208 9G6005 1 PIN FOOT GND1 1
209 33G8020 2E F CONNECTOR CN801 1
210 33G8020 2E F CONNECTOR CN802 1
1.0
211 40G 45762420A ID LABEL
2
212 56G 139 7 1 IC EL817MA M-TYPE IC902 1
213 61G 58120 WT NTCR 12OHM NR901 1
214 61G152M688 64 0.68OHM +-5% 2W R920 1
215 63G 10747410S 0.47UF +-10% 250VAC C903 1
216 65G 3J1506ET 15PF 5% SL 3KV TDK C816 1
217 65G 3J2096ET 2PF 5% SL 3KV C802 1
218 65G305M1022E2 1000PF C901 1
219 65G305M1022E2 1000PF C902 1
220 65G306M2222BP 2200PF Y1 400 20% BY UK C900 1
221 67G 30510115K 105℃ELE CAP C905 1
222 67G215V471 4N 470UF+-20% 25V C916 1
223 67G215V471 4N 470UF+-20% 25V C917 1
224 67G215V471 4N 470UF+-20% 25V C918 1
225 67G215V471 4N 470UF+-20% 25V C920 1
226 67G215V471 4N 470UF+-20% 25V C921 1
227 67G215V471 4N 470UF+-20% 25V C924 1
228 67G415V221 6K CAP105℃ 220UF M 35V C811 1
229 73G 174 65 H LINE FILTER L902 1
230 73G 253 91 H CHOKE COIL L903 1
231 73G 253 91 H CHOKE COIL L904 1
232 73L 174 50 HH LINE FILTER L901 1
233 87G 501 37 S AC INLET ST-01DG-B2A-K CN901 1
234 93G 50460 28 BRIDGE KBP208G 2A 800V BD901 1
235 93G 6026T52T FR107-DO-41 1000V/1A D901 1

- 47 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
236 93G3006 1 1 31DQ06FC3 NIHON INTER D902 1
237 95G8014 9D543 WIRE HARNESS CN902 1
238 96G 29 10 CB H.S.TUBE CHANGBAO-102 20
239 705GJ7K0 61001 R910 ASS'Y 1
240 705GQ5K0 57001 Q903 ASS'Y 1
241 705GQ5K0 93001 D904 ASS'Y 1
242 Q51G 6 4508 RTV GLUE 2
243 56G 379 76 IC LD7552BPS SOP-8 IC901 1
244 56G 608 10 OZ9938GN SOIC-16 IC801 1
245 57G 417 4 PMBS3904/PLILIPS Q802 1
246 57G 417 4 PMBS3904/PLILIPS Q803 1
247 57G 417 4 PMBS3904/PLILIPS Q901 1
248 57G 759 2 TRANSISTOR RK7002 SOT-3 Q801 1
249 57G 759 2 TRANSISTOR RK7002 SOT-3 Q804 1
250 57G 759 2 TRANSISTOR RK7002 SOT-3 Q806 1
251 57G 759 2 TRANSISTOR RK7002 SOT-3 Q807 1
252 57G 763 14 AM9945N-T1-PF SOIC-8 Q805 1
253 61G0805100 RST CHIP 10R 1/8W 5% R917 1
254 61G0805100 1F RST CHIP 1K 1/8W 1% R918 1
255 61G0805100 1F RST CHIP 1K 1/8W 1% R928 1
256 61G0805100 1F RST CHIP 1K 1/8W 1% R931 1
257 61G0805100 2F RST CHIP 10K 1/8W 1% R804 1
258 61G0805100 2F RST CHIP 10K 1/8W 1% R812 1
259 61G0805100 2F RST CHIP 10K 1/8W 1% R919 1
260 61G0805100 3F RST CHIPR 100KOHM +-1% 1 R810 1
261 61G0805100 3F RST CHIPR 100KOHM +-1% 1 R815 1
262 61G0805100 3F RST CHIPR 100KOHM +-1% 1 R821 1
263 61G0805100 3F RST CHIPR 100KOHM +-1% 1 R915 1
264 61G0805102 RST CHIP 1K OHM +/-5% 1/ R819 1
265 61G0805102 RST CHIP 1K OHM +/-5% 1/ R831 1
266 61G0805102 RST CHIP 1K OHM +/-5% 1/ R935 1
267 61G0805105 RST CHIP 1M 1/8W 5% R813 1
268 61G0805105 RST CHIP 1M 1/8W 5% R816 1
269 61G0805105 RST CHIP 1M 1/8W 5% R822 1
270 61G0805105 RST CHIP 1M 1/8W 5% R826 1
271 61G0805105 RST CHIP 1M 1/8W 5% R829 1
272 61G0805150 RST CHIP 15R 1/8W 5% R832 1
273 61G0805150 RST CHIP 15R 1/8W 5% R833 1
274 61G0805184 RST CHIP 180K 1/8W 5% R834 1
275 61G0805220 RST CHIP 22R 1/8W 5% R807 1

- 48 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
276 61G0805243 1F RST CHIPR 2.43 KOHM +-1% R936 1
277 61G0805304 RST CHIPR 300 KOHM +-5% R802 1
278 61G0805330 0F RST CHIPR 330 OHM +-1% 1 R827 1
279 61G0805330 0F RST CHIPR 330 OHM +-1% 1 R930 1
280 61G0805330 2F RST CHIP 33 KMOHM +-1% 1 R817 1
281 61G0805330 2F RST CHIP 33 KMOHM +-1% 1 R934 1
282 61G0805390 1F RST CHIPR 3.9 KOHM +-1% R937 1
283 61G0805433 RST CHIPR 43 KOHM +-5% 1 R814 1
284 61G0805563 RST CHIP 56K 1/8W 5% R820 1
285 61G0805680 2F RST CHIP 68K 1/8W 1% R818 1
286 61G0805752 RST CHIP 7K5 1/8W 5% R825 1
287 61G1206000 RST CHIP MAX 0R05 1/4W JR901 1
288 61G1206000 RST CHIP MAX 0R05 1/4W R801 1
289 61G1206000 4 CHIP 0OHM 4A F902 1
290 61G1206101 RST CHIP 100 OHM +/-5% 1 R922 1
291 61G1206101 RST CHIP 100 OHM +/-5% 1 R923 1
292 61G1206101 RST CHIP 100 OHM +/-5% 1 R924 1
293 61G1206101 RST CHIP 100 OHM +/-5% 1 R925 1
294 61G1206101 RST CHIP 100 OHM +/-5% 1 R926 1
295 61G1206101 RST CHIP 100 OHM +/-5% 1 R927 1
296 61G1206102 RST CHIP 1K OHM +/-5% 1/ R903 1
297 61G1206102 RST CHIP 1K OHM +/-5% 1/ R914 1
298 61G1206102 RST CHIP 1K OHM +/-5% 1/ R921 1
299 61G1206102 RST CHIP 1K OHM +/-5% 1/ R929 1
300 61G1206102 RST CHIP 1K OHM +/-5% 1/ R932 1
301 61G1206103 RST CHIP 10K OHM +/-5% 1 R803 1
302 61G1206249 RST CHIPR 2.4 OHM +-5% 1 R916 1
303 61G1206434 RST CHIPR 430 KOHM +-5% R904 1
304 61G1206434 RST CHIPR 430 KOHM +-5% R905 1
305 61G1206471 RST CHIP 47OR 1/4W 5% R805 1
306 61G1206473 CHIP 47K OHM 1/4W R808 1
307 61G1206514 RST CHIPR 510 KOHM +-5% R907 1
308 61G1206514 RST CHIPR 510 KOHM +-5% R908 1
309 61G1206514 RST CHIPR 510 KOHM +-5% R909 1
310 61G1206684 RST CHIP 680 KOHM +/-5% R900 1
311 61G1206684 RST CHIP 680 KOHM +/-5% R901 1
312 61G1206684 RST CHIP 680 KOHM +/-5% R902 1
313 65G0805102 32 CHIP 1000PF 50V X7R 0805 C805 1
314 65G0805102 32 CHIP 1000PF 50V X7R 0805 C817 1
315 65G0805102 32 CHIP 1000PF 50V X7R 0805 C819 1

- 49 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
316 65G0805102 32 CHIP 1000PF 50V X7R 0805 C821 1
317 65G0805102 32 CHIP 1000PF 50V X7R 0805 C822 1
318 65G0805103 22 CHIP 0.01UF 25V X7R 0805 C801 1
319 65G0805103 22 CHIP 0.01UF 25V X7R 0805 C807 1
320 65G0805103 22 CHIP 0.01UF 25V X7R 0805 C906 1
321 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C911 1
322 65G080510422T CAP 0805 0.1UF K 25V X7R C808 1
323 65G080510422T CAP 0805 0.1UF K 25V X7R C812 1
324 65G080510422T CAP 0805 0.1UF K 25V X7R C907 1
325 65G080510422T CAP 0805 0.1UF K 25V X7R C908 1
326 65G080510422T CAP 0805 0.1UF K 25V X7R C909 1
327 65G080510422T CAP 0805 0.1UF K 25V X7R C919 1
328 65G0805105 12 CHIP CAPACITOR 1UF 16V X C806 1
329 65G0805221 32 CHIP 220PF 50V X7R C912 1
330 65G0805223 22 E65 C809 1
331 65G0805471 31 CHIP 470PF 50V NPO C818 1
332 65G0805473 32 SMD 47NF +-10% 50V C815 1
333 65G080556131G MLCC 0805 560PF G 50V NP C810 1
334 65G1206102 72 CHIP 1000PF 500V X7R C914 1
335 65G1206102 72 CHIP 1000PF 500V X7R C915 1
336 65G1206225 22 2.2UF 25V X7R 1206 C804 1
337 93G 64 42 P BAV70 DIODE D801 1
338 93G 64 44 S CHIP DIODE LL4148WP D803 1
339 93G 64 44 S CHIP DIODE LL4148WP D804 1
340 93G 6433P BAV99 SOT-23 D802 1
341 93G 39GA28 T RLZ13B ZD903 1
342 93G 39GA28 T RLZ13B ZD904 1
343 93G 39S 24 T RLZ5.6B ROHM ZD801 1
344 93G 39S 24 T RLZ5.6B ROHM ZD902 1
345 93G 39S 45 T RLZ36B ZENER DIODE ZD901 1
346 6G 31500 2.0MM EYELET CN901 2
347 6G 31502 1.5MM RIVET C905 2
348 6G 31502 1.5MM RIVET L901 4
349 6G 31502 1.5MM RIVET L902 4
350 6G 31502 1.5MM RIVET NR901 2
351 6G 31502 1.5MM RIVET PT801 2
352 6G 31502 1.5MM RIVET Q903 1
353 6G 31502 1.5MM RIVET T901 4
354 56G 158 10 T IC AZ431AZ-AE1 TO-92 IC904 1
355 61G 60210052T 10 OHM 5% 1/6W J914 1

- 50 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
356 61G 60210052T 10 OHM 5% 1/6W J921 1
357 61G212Y625 KT MGFR 6.2MOHM +-5% 1/2W R823 1
358 65G 1K152 1T 1500PF +/-10% 1KV Y5P C904 1
359 67G215Y2207KT LOW ESR EC 22uF 50V 5*1 C910 1
360 71G 55 9 T FERRITE BEAD J908 1
361 71G 55 29 Φ3.5*Φ0.8*2.2\ 100MM> FB901 1
362 84G 55 7W 250V/3.15A FUSE F901 1
363 93G 6038T52T FR103 DO-41 200V/1A D903 1
364 95G 90 23 TINCOATEDCOPPER J901 1
365 95G 90 23 TINCOATEDCOPPER J902 1
366 95G 90 23 TINCOATEDCOPPER J903 1
367 95G 90 23 TINCOATEDCOPPER J904 1
368 95G 90 23 TINCOATEDCOPPER J905 1
369 95G 90 23 TINCOATEDCOPPER J906 1
370 95G 90 23 TINCOATEDCOPPER J907 1
371 95G 90 23 TINCOATEDCOPPER J909 1
372 95G 90 23 TINCOATEDCOPPER J910 1
373 95G 90 23 TINCOATEDCOPPER J911 1
374 95G 90 23 TINCOATEDCOPPER J912 1
375 95G 90 23 TINCOATEDCOPPER J913 1
376 95G 90 23 TINCOATEDCOPPER J915 1
377 95G 90 23 TINCOATEDCOPPER J916 1
378 95G 90 23 TINCOATEDCOPPER J918 1
379 95G 90 23 TINCOATEDCOPPER J919 1
380 95G 90 23 TINCOATEDCOPPER J920 1
381 95G 90 23 TINCOATEDCOPPER J922 1
382 95G 90 23 TINCOATEDCOPPER J923 1
383 95G 90 23 TINCOATEDCOPPER J924 1
384 95G 90 23 TINCOATEDCOPPER J925 1
385 95G 90 23 TINCOATEDCOPPER J927 1
386 95G 90 23 TINCOATEDCOPPER J930 1
387 715G2274 2 VS POWER BOARD PCB 1
388 61G152M10458G 100K OHM 5% 2W R910 1
389 96G 29 6 SHRINK TUBE UL/CSA 20
390 57G 724 11 STP9NK65ZFP TO-220FP MOS Q903 1
391 90G6084 1 HEAT SINK 1
392 AM1G1730 8120 SCREW XN01A 1
393 90G6084 1 HEAT SINK 1
394 93G 60294 DIODE MBRF10150CT 10A/1 D904 1
395 AM1G1730 8120 SCREW XN01A 1

- 51 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
8. Exploded Diagram And Spare Parts List

- 52 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
Packing For Shipping

- 53 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
9. Disassemble Process
9.1 Units Disassemble Process
9.1.1 Tools
— Glove
— Big cross screwdriver
— Small cross screwdriver
— Prize equipment or abandoned IC card
— Screw box
— Cushion
— Six angle sleeve spanner

9.1.2 Disassemble process

1、 Tide up the worktable, spread straight cushion, put the monitor on it, the front side
adown.(Picture 1)
2、 Disassemble the base of the monitor. (Picture 2, 3)
3、 Remove the decorate slice of the back cover.(Picture 4)
4、 Disassemble the 4 screws that fix the stand, remove the stand.(Picture 5)
5、 Disassemble the screws of the back cover.（Picture 6）
6、 Use equipment or abandoned IC card to prize up the bezel through the bottom flute,
and rip up the back cover downwards.( as showed in the following the picture
7,8,9,10)
7、 Disassemble the screw of the Key board. (picture 11)
8、 Remove the bezel, refer to the following picture 12,13.
9、 Disassemble the 2 pins of the backlight, as showed in the following the picture 14,15.
10、 Disassemble the 4 fixed screws of the panel, as showed in the following the
picture16,17.
11、 Lift up the main frame and lift down the LVDS connectors according to the direction of
the arrowhead, refer to the following picture 18,19.
12、 That’s all. The disassemble process of the unit is over.
9.1.3 Show pictures：

（Picture 1） （Picture 2）

- 54 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 （Picture 3） （Picture 4）

（Picture 5） （Picture 6）

（Picture 7） （Picture 8）

（Picture 9） （Picture 10）

- 55 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 （Picture 11） （Picture 12）

（Picture 13） （Picture 14）

（Picture 15）

（Picture 16）

（Picture 17）

- 56 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 （Picture 18） （Picture 19）

（Picture 20）

- 57 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
10. Block Diagram

- 58 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11. Schematic Diagram
11.1 Power
VCC3.3
3/16
VCC3.3 VCC3.3
BAT54C : IF 10mA,VF=0.4V
BAV70 : IF 10mA,VF=0.855V
BAT54C
R401 R403 D106 (drop voltage too much)
10K 1/16W 10K 1/16W VCC1.8
CN401 MVCC U702
BKLT-EN
1 CMVCC R402 3.3 2W 3 2
2 C406 VI VO
3 CMVCC C412 C403 +

GND
4 CMVCC NC 100uF/16V
5 BKLT-VBRI R404 0.1uF/16V C413 C402 +
on_BACKLIGHT 3
6 BKLT-EN 4K7 1/16W 100uF/16V
7 C_PANEL_INDEX Q403 0.1uF/16V

1
PANEL_ID# 3
8 Volume 2N3904S-RTK/PS
9 Mute
Mute 3
*12/28 change to LDO due to
CONN internal ripple too big

CN401 SWAP
BKLT-VBRI & BKLT-EN
VCC3.3 VCC3.3
070307

R410 R411

NC/10K 1/16W NC/10K 1/16W CMVCC MVCC FB402

Volume
NC
VCC3.3
DGND 2,3,4
U701
Q405 3 2
Volume# 3 VIN VOUT
NC/2N3904S-RTK/PS

VSS
R412
NC/4K7 1/16W
C407 + C409 AP1117E33LA C401 + C408
100uF/16V
NC Audio function 100uF/16V

1
VCC3.3 0.1uF/16V 0.1uF/16V
070330

R405

NC
DSUB_5V Q404
2N3904S-RTK/PS VCC3.3
BKLT-VBRI R406 1K 1/16W
adj_BACKLIGHT 3
C410
R407 C411
1uF 10V 1K 1/16W
R405 NC R408 1uF 10V
3K 1/16W 5%
R408 Change 5%
070320 070308
U402
AZ431AN-AE1
R409
10K 1/16W

Q403,Q404,Q405
Change to 2N3904
070308
TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL VSC VA1723w-2 Size B

絬隔瓜絪腹 G2632-C-X-X-1-070403 TPV MODEL K17W Rev D

Key Component 5.0.POWER PCB NAME 715G2632-C
称爹 <称爹>
Date Wednesday , April 04, 2007 Sheet 1 of 5

- 59 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11.2 Input
R101 0R05 1/16W R102 100R 1/16W
DSUB_H 3
R103 100R 1/16W FB102
DSUB_V 3

2
VGA_B+ 1 2 R104 100R 1/16W C101
DSUB_B+ 3
R105 R106 C102 C103 BEAD 0.047uF
ZD101 ZD102 2K 1/16W
UDZS5.6B UDZS5.6B 2K 1/16W 22pF 22pF R107 C104
5pF/50V
75R 1/16W

1
VGA_B- R108 100R 1/16W C105
DSUB_B- 3
CN101 0.047uF

16
10 R109 390 1/16W C106
DSUB_SOG 3
DDC1_SCL 100R 1/16W 15 5 VGA_PLUG FB103 0.047uF
3 DDC1_SCL
R110 9 DSUB_5V DSUB_5V
14 4 VGA_G+ 1 2 R111 100R 1/16W C107
DSUB_G+ 3

2
8 VGA_B- BEAD 0.047uF
13 3 VGA_B+
7 VGA_G- ZD103 ZD104 R112 C108
DDC1_SDA 100R 1/16W 12 2 VGA_G+ UDZS5.6B UDZS5.6B 5pF/50V
3 DDC1_SDA
R113 6 VGA_R- 75R 1/16W
2

11 1 VGA_R+

1
VGA_G- R114 100R 1/16W C109
DSUB_G- 3
ZD105 ZD106 17 DB15 0.047uF
UDZS5.6B UDZS5.6B

VGA_R+

VGA_G+

3 VGA_B+
1

FB101

VGA_R+ 1 2 R115 100R 1/16W C110

DSUB_R+ 3
3

3
D102 D103 D104 CMVCC BEAD 0.047uF
BAV99 BAV99 BAV99
R116 C111
5pF/50V
C114 C115 C116 75R 1/16W
C112
VGA_R- R117 100R 1/16W C113
2

1
0.1uF/16V DSUB_R- 3
0.047uF
GND POWER DGND 0.1uF/16V 0.1uF/16V 0.1uF/16V

VCC3.3

CMVCC DSUB_5V
R137
10K 1/16W

VGA_PLUG DET_CABLE 3
BAV70
D105

R120 R121
C414 4K7 1/16W 4K7 1/16W
0.1uF U703 R413
1 8 10K 1/16W
2 A0 VCC 7
A1 WP EDID_WP 3
3 6 DDC1_SCL
4 A2 SCL 5 DDC1_SDA
GND SDA

M24C02-WMN6TP

TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL VSC VA1723w-2 Size B

絬隔瓜絪腹 G2632-C-X-X-1-070403 TPV MODEL K17W Rev D

Key Component 2.0. INPUT PCB NAME 715G2632-C
称爹 <称爹>
Date Wednesday , April 04, 2007 Sheet 1 of 5

- 60 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11.3 Scaler
VDDC
AVDD VDDP
VDDP
VCC3.3 FB203 AVDD

51

30
53
2,5 VCC3.3

6
600 OHM
52 C203

VDDP
AVDD_ADC

VDDC
VDDC
VCTRL C202 +
33 PA0 NC/4.7uF16V 0.1uF/16V C207
13 LVA3P 34 PA1 0.1uF/16V
2 DSUB_R+ RIN0P LVA3M
12
2 DSUB_R- RIN0M
10
2 DSUB_G+ GIN0P
9 35 PA2
2 DSUB_G- GIN0M LVA2P
11 36 PA3
2 DSUB_SOG SOGIN0 LVA2M
8 37 PA4
2 DSUB_B+ BIN0P LVA1P
7 38 PA5
2 DSUB_B- BIN0M LVA1M
16 39 PA6 VCC1.8 VDDC
2 DSUB_H HSY NC0 LVA0P
17 40 PA7
2 DSUB_V VSY NC0 LVA0M
18
2 DDC1_SDA DDCA_SDA/RS232_TX 5 VCC1.8
19
2 DDC1_SCL DDCA_SCL/rs232_RX
C209 + C211
NC C202,C209
NC/4.7uF16V 070330
PA[0..7] C212
PA[0..7] 4
0.1uF/16V
41 PB0 PB[0..9] 0.1uF/16V
LVB3P PB[0..9] 4
42 PB1
LVB3M 43 PB2
LVBCKP 44 PB3
LVBCKM 45 PB4
LVB2P 46 PB5
R204 LVB2M 47 PB6
390 1/16W LVB1P 48 PB7
LVB1M
VCC3.3
AVDD 4
REXT U401 LVB0P
49
50
PB8
PB9
LVB0M
EDID_WP 3
15
R415 NC 0.1uF/16V REFP VCC3.3
C201 TSUM16AWR-LF-1 Q406
14 2N3904S-RTK/PS
REFM CMVCC VCC3.3
R414 C415 R205

C218 20 R232 10K 1/16W 10K 1/16W 0.1uF/16V 10K 1/16W

0.1uF/16V U203 GPIO_P15/PWM0 27 R230 100R 1/16W R209
PWM2/GPIO_P24 PANEL_ID# 5
1
CE# VDD
8 21
SDO LVDS R208
R210 2 7 22 55 6K8 1/16W 10K 1/16W PMBS3906
SO HOLD# SCZ GPIO_P12 on_BACKLIGHT 5
WP 3 6 23 56 Q202
WP# SCK SCK PWM1/GPIO_P25 adj_BACKLIGHT 5
10K 1/16W 4 5 24
VSS SI SDI 57 R211 10K 1/16W LED_ORANGE
SST25LF020A-33-4C-SAE R207 100R 1/16W 28 RSTN 58 R213 100R 1/16W KEY 1 Q203 R212 75R 1/16W
GPIO_P27/PWM1 GPIO_P00/SAR1 59 R214 100R 1/16W KEY 2 PMBS3906
C220 GPIO_P01/SAR2 C219 LED_GRN/BLUE
54 0.1uF/16V R216 75R 1/16W
+

CMVCC RST 60 R217 4K7 1/16W

4.7uF16V R219 GPIO_P06 61 R218 4K7 1/16W
100K 1/16W GPIO_P07 62 R220 NC
PWM0/GPIO_P26 Volume# 5
R201 63 R222 100R 1/16W POWER_KEY #
GPIO_P13 VCC3.3
0R05 1/16W 1 64 R221 NC R223 10K 1/16W
XIN GPIO_P14 Mute 5
2

C221 22pF
X201
14.318MHz 2
C222 22pF XOUT
1

26
GPIO_P10/I2C_MCL PPWR_ON# 4
25 R215 100R 1/16W
GPIO_P11/I2C_MDA DET_CABLE 2
31
32 MODE[0]
GND
GND
GND

MODE[1]
Add R415
070330
29
3
5

R226 R227

10K 1/16W 10K 1/16W

VCC3.3

U401Change to R228 R229

TSUM16AWR-LF-1 3.9K 1/16W 3.9K 1/16W
CN201
070330
1 KEY 2
2 KEY 1
3 POWER_KEY #
4 LED_GRN/BLUE
5 LED_ORANGE
6

C225 C226 C227 C228 C229

CONN 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V

Near to Connect

TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL VSC VA1723w-2 Size C

絬隔瓜絪腹 G2632-C-X-X-1-070403 TPV MODEL K17W Rev D

Key Component 3.0.SCALER PCB NAME 715G2632-C
称爹 <称爹>
Date Wednesday , April 04, 2007 Sheet 1 of 5

- 61 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11.4 Panel Interface
CN301

PB[0..9] PB9 LVB0M 1 2 PB8 LVB0P

3 PB[0..9]
PB0 LVB3P PB7 LVB1M 3 4 PB6 LVB1P
PB1 LVB3M PB5 LVB2M 5 6 PB4 LVB2P
PB2 LVBCKP PB3 LVBCKM 7 8 PB2 LVBCKP
PB3 LVBCKM PB1 LVB3M 9 10 PB0 LVB3P
PB4 LVB2P PA7 LVA0M 11 12 PA6 LVA0P
PB5 LVB2M PA5 LVA1M 13 14 PA4 LVA1P
PB6 LVB1P PA3 LVA2M 15 16 PA2 LVA2P
PB7 LVB1M PB3 LVBCKM 17 18 PB2 LVBCKP
PB8 LVB0P PA1 LVA3M 19 20 PA0LVA3P
PB9 LVB0M 21 22
23 24
PA[0..7]
3 PA[0..7]
PA0 LVA3P CONN
PA1 LVA3M

PANEL_VCC
PA2 LVA2P
PA3 LVA2M
PA4 LVA1P
PA5 LVA1M
PA6 LVA0P
PA7 LVA0M
C302
0.1uF/16V

R302
330R 1/8W 5%

3 D

CMVCC 1 2
G S
AO3401L
C301
R303 R301
4K7 1/16W 10K 1/16W 0.1uF/16V
R304
PANEL_VCC
2006-11-7 Add pull up 4K7 to MVCC Q302
100K 1/16W AO3401 FB301
PPWR_ON# Q301
3 PPWR_ON#
PMBS3906 120

+ C303
100uF/16V

TP V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL VSC VA1723w-2 Size A

絬 隔 瓜 絪 腹 G2632-C-X-X-1-070403 TPV MODEL K17W Rev D

Key Component 4.0. PANEL INTERFACE PCB NAME 715G2632-C
称爹 <称爹>
Date Wednesday , April 04, 2007 Sheet 1 of 5

- 62 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11.5 Inverter
R801 CN801
47KΩ 1/4W
+12V PT801
1 POWER X'FMR
8 1
2

R802 R804 R805 4

300KΩ 1/8W 10KΩ 1/4W 470R 1/4W 3 CONN
C816
C811 C819 R832 R833 C817 15pF/3KV
+ 0.001uF 15R 1/8W 15R 1/8W 0.001uF
6 7 R831
Q802 1K 1/8W
PMBS3904 220uF 35V
ON/OFF Q803 C814 R806
C802
Q801 PMBS3904 2pF/3KV
RK7002 VCC

2
R803 ZD801 NC NC R821
C821 C822 CN802
10KΩ 1/4W RLZ5.6B 100KΩ 1% 1/8W R823
C801 6.2MΩ 1/2W
0.01uF/25V 1

1
0.001uF 0.001uF C818 2
R820
470pF/50V
56K 1/8W

CONN

5
D

D
Q805
AM9945N-T1-PF
R807

G
S

S
22R 1/8W D801

R824
R825

NC
BAV70 7K5 1/8W

4
DIM

R819
1K 1/8W

R808

330Ω 1% 1/8W
R809 NC
47K 1/4W

100KΩ 1% 1/8W
J914 D802
10Ω J921 3 BAV99

R828
NC
0.047uF
C806 10Ω R817

C815
R810 1uF/16V R816 33K 1/8W 1

R827
100KΩ 1% 1/8W 1M 1/8W

R815
IC801
1 16
2 DRV1 PGND 15
3 VDDA DRV2 14
4 TIMER GNDA 13
5 DIM CT 12
PID 6 ISEN SSTCMP 11
R812 7 VSEN LCT 10
10K 1/8W 8 OVPT ENA 9
NC1 NC2

C813
NC

0.022uF/25V
C810

0.01uF/25V
1M 1/8W OZ9938GN 560PF/50V
C805
R813

C807

C809
R811 0.001uF
NC R814
R830 C820 C804 43KΩ 1/8W
NC NC 2.2uF/25V R834
180K 1/8W

R818
68K 1/8W

VCC

R822
1M 1/8W

Q804
RK7002 D803
LL4148WP
Q806
RK7002

1M 1/8W
0.1uF25V

R826
C803

C808
NC
D804
LL4148WP
Q807
RK7002

1M 1/8W
0.1uF25V
C812

R829
TPV (Top Victory) Electronics Co., Ltd.
Title

G2274-1-VS-X-1-070419
Size Document Number Rev
A3
PWPC721HV1J A

Date: Thursday , April 19, 2007 Sheet 1 of 2

- 63 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11.6 A-D Power
R922
100Ω 1/4W
R923
100Ω 1/4W
T901 C914
R924 0.001uF
4 POWER X'FMR
100Ω 1/4W

1K 1/4W

1K 1/4W

1K 1/4W

1K 1/4W
1 3
5 9
1

R921

R932

R929

R903
R904 10 J908
BD901 R910 D904
430KΩ 1/4W STPS10150CG
KBP208G R907 C904 100KΩ 2W

2
+

510KΩ 1/4W 6 7 1 2
+12V

2
2 3 1500pF/1KV L903
3 8 BEAD
3.5uH ZD903
+ C905 + + C917 RLZ13B
100uF/450V R905 11 470uF/25V + C918
12 R925 C915 C916 470uF/25V
430KΩ 1/4W
-

R908 1 100Ω 1/4W 0.001uF 470uF/25V

510KΩ 1/4W C919
R926

1
R914 0.1uF25V
100Ω 1/4W
4

1K 1/4W

2
ZD901 D901 R927
RLZ36B FR107 100Ω 1/4W Q901
R909 PMBS3904
510KΩ 1/4W
D903

1
FR103 C906 R933
4 3
NC
L902 0.01uF/25V
7.0mH R916 D902
+ C910 2.4Ω 1/4W 31DQ06FC3 5V
1 2
22uF/50V
C909 L904
0.1uF05V 3.5uH F902
C902 C924 + C921 0Ω 1/4W
1000pF 470uF/25V + + C920 470uF/25V C908
470uF/25V 0.1uF25V
R917
C901 IC901 10R 1/8W Q903
3

1000pF 1 8 2SK2645-54MR
L901 2 GND OUT 7
3 COMP VCC 6
4.0mH 4 VCC CS 5
RT NC

2
R918

2
LD7552BPS 1K 1/8W R930 ZD904 ZD902
FB901 330Ω 1% 1/8W RLZ13B RLZ5.6B
2

BEAD

C903

1
0.47uF/275V R915 R919

2
100KΩ 1% 1/8W 10K 1/8W

VAR901 C911 C912 R920 R937 R934

NC 0.01uF/25V 220pF 0.68Ω 2W 3K6 1/8W 33K 1/8W

R901 R900
680KΩ 1/4W 680KΩ 1/4W R928
1K 1/8W CN902
R931

1
1K 1/8W 1
R902 IC902 GND 2
EL817MA DIM PWM
680KΩ 1/4W 3
ON/OFF ON/OFF 4
PID PID 5
1

2
NR901
NTCR F901 GND 6
+12V 12V
FUSE 7
12V 8
C907
t 0.1uF25V 5V
GND
3.3V
9
10
3.3V 11
2

GND 12
C900 R935 GND
0.0022UF 1K 1/8W
Pitch 2.54mm
CONN
3

2 1
CN901 IC904 R936
SOCKET KIA431A-AT/P 2.43KΩ 1% 1/8W

TPV (Top Victory) Electronics Co., Ltd.

Title
G2274-1-VS-X-1-070419
Size
B
Document Number
PWPC721HV1J Rev
C

Date: Tuesday , May 15, 2007 Sheet 1 of 2

- 64 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 11.7 Key Pad

KEY 1 R001 3K 1/10W 5% UP

KEY 2 R002 3K 1/10W 5% DOWN

POWER

ORANGE

GREEN

R003 2K 1/10W

R004 2K 1/10W

SW001 SW002 SW003 SW004 SW005

SW SW SW SW SW

CN001

6 KEY 2
KEY1 KEY2 DOWN UP
5 KEY 1
4 POWER GND
3 GREEN
2 ORANGE
1
ON/OFF
GND
CONN

CN101 Change to Right angle

070410

TP V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL VSC VA1723w-2 Size A

絬 隔 瓜 絪 腹 G2622-C-X-X-1-070412 TPV MODEL K17W Rev C

Key Component 1. Key board PCB NAME 715G2622-B
称爹 <称爹>
Date Wednesday , April 25, 2007 Sheet 2 of 2

- 65 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
12. PCB Layout Diagram

12.1 MAIN BOARD PCB TOP VIEW

- 66 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
12.2 MAIN BOARD PCB BUTTON VIEW

- 67 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
12..3 POWER PCB TOP VIEW

- 68 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
12.4 POWER PCB BUTTON VIEW

- 69 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
12.5 KEY BOARD TOP VIEW

12.6 KEY BOARD BUTTON VIEW

- 70 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w
 * Reader’s Response*
Dear Readers:
Thank you in advance for you feedback on our Service Manual, which allows continuous
improvement of our products. We would appreciate your completion of the Assessment Matrix
below, for return to ViewSonic Corporation.

Assessment
A. What do you think about the content after reading VA1716w Service Manual?

Unit Excellent Good Fair Bad

1. Precautions And Safety Notice
2. Specification
3. Front Panel Control and Indicators
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram And Spare Parts List
9. Block Diagram
10. Schematic Diagram
11. PCB Layout Diagram

B. Are you satisfied with the VA1716w Service Manual?

Item Excellent Good Fair Bad

1. Service Manual Content
2. Service Manual Layout
3. The form and listing

C. Do you have any opinion and suggestion about this Service Manual?
Reader’s Basic Data:

Name: Title:
Company:
Add:
Tel: Fax :
E-Mail:

After completing this form, please return it to ViewSonic Quality Assurance in the USA at
facsimile 1-909-839-7943. You may also e-mail any suggestion to the Director, Quality System
& Process ([email protected])

- 71 –
ViewSonic Corporation Confidential - Do Not Cop VA1716w