Customer: Date:

Job/Project:
800-233-6294 Quantity: Ref/Tag:

Shown with Style 1101 Rubber Expansion Joint

Control Unit 4” ID x 6” F/F (DN100mm x 152mm) - 150-lb Drilling | 1101-0004-3.16
GR/B 7/8” thk.
[22.2mm]

Section Detail
Mating Rod ∅5/8” x 16” Retaining Ring Cover
Rubber (segmented)
Flange [15.9mm x 406.4mm] Grommet
(by others)
Reinforcement
Unfilled Arch 6” [152.4mm] Tube
Filled Arch
(reduce movements by 50%,
increase spring rates by 400%)
Nuts
Pure Gum Neoprene Butyl Nitrile EPDM Viton®
(Buna-N) (FKM)
Tube
∅4” ID Cover
[101.6mm] Tire Cord: º F [º C] º F [º C] º F [º C] º F [º C] º F [º C] º F [º C]
Polyester 180 [82] 225 [107] 250 [121] 210 [99] 250 [121] 250 [121]
∅7 1/2” BC Kevlar® 180 [82] 225 [107] 300 [149] 210 [99] 350 [177] 400 [204]
[190.5mm] Maximum Temperature rating based on lowest temperature material selected. EPDM or
Butyl w/Polyester Tire Cord rated 300°F (149°C) for Air Service up to 25 psig (1.7 barg)
∅9” OD
[228.6mm] Bill of Materials
∅3/4” [19mm] ITEM MATERIAL FINISH
(8 holes) Retaining Ring Carbon Steel Hot Dipped Galvanized
∅13 3/8” Max OD
[338mm] Stainless Steel Plain
Gusset Carbon Steel Hot Dipped Galvanized
*Gusset Stainless Steel Plain
9/16” thk. [14mm] Rods ASTM A193 B7 Alloy Steel Hot Dipped Galvanized
ASTM A193 B8M 316 SS Plain
Nuts ASTM A194 2H Steel Hot Dipped Galvanized
ASTM A194 8M 316 SS Plain
Spherical Washers Stainless Steel Plain
Metal Reinforcement High Tensile Steel Rubber Embedded
Textile Reinforcement Tire Cord RFL Coating
MOVEMENT (non-concurrent) SPRING RATE PRESSURE WEIGHT
Comp. Ext. Lateral Angular Torsional Comp. Ext. Lateral Angular Torsional Pressure Vacuum RBJ with Control
in [mm] in [mm] in [mm] deg. deg. lb/in lb/in lb/in ft-lb/deg ft-lb/deg psig in-Hg Rings Unit
[N/mm] [N/mm] [N/mm] [N-m/deg] [N-m/deg] [barg] [barg] lbs [kg] lbs [kg]
1 3/4 [44] 7/8 [22] 1 [25] 22 3.6 550 [96] 710 [124] 590 [103] 1.9 [2.58] 3.5 [4.75] 225 [15.5] 30 [-1] 14 [6] 11 [5]

Inner Nuts (GR/W) Spherical Washer (GR-SW/B) Spherical Washer (GR-SW/SW)

Optional
Control Units
No Control Units

Outer Washer / Integral Ring (INT-W/B) Integral Ring (INT-W/W) Integral Ring, Spherical Washer
(INT-SW/SW)
Grommet
Inner Bare (GR/B)
(shown above)

*No. of Rods: 2 Rods / 225 psig

*Gusset thickness and pressure listed above are for carbon steel gussets and ASTM A193 B7 rods. Contact General Rubber for stainless steel pressures and thicknesses.
Contact General Rubber Corporation for full product specifications, Warnings and installation instructions.
© 2016 General Rubber Corporation, All Rights Reserved general-rubber.com