Intelligent Solar Charge Controller 1 Product intr oduction

This controller is a kind of intelligent and multifunctional solar

User s M anual charge controller.These serial productsadopt customized LCDdisplay
screen, which makesthe operation onthe interface ratherconvenient.
All the controllingparameters can bereset flexibly to satisfy your different
needs. This controller has the following features:

Visual LCD graphic symbol

Brief key operation
Grade auto switchof system voltage
Intelligent PWM Charging Mode
Auto temperature compensation
Adjustable charging &discharging parameter
Settable working modesof loads
Accumulative function ofcharging & discharging AH
Protection for batteryback discharging
Protection for batterylow voltage
Overloading & short-circuit protection
Battery reversed protection
Please read this instru ction carefully before using it.
Delayed auto restartafter overloading protection
SOLAR30 12V/24V AUTO WORK 1 2

2 Installation Explanation 3. Operation

Installation
Get ready the related tools& cables. We suggest you choose the appropriate cables 1. Explanation of LCD Graphic Symbol
to ensure the current density 4A/mm2 and this is good for reducing cable voltage
drop. Recommendation 30A using 10mm2 cable 50A using 16 mm2 cable. stop supplying powerfor loads
Check whether installation Temperature Controller supplying power forloads,
place accords with the relative sensor
interface
safety rules. Please avoid installing no current inload loop
and using the controller under
the following conditions: wet, having current inload loop
dusty places or places with
flammable and explosive gases. load icon
Install the controller at the solar panels icon
vertical plane. Please refer to
chapter 5 for more detailedinfo Solar panels DC load load light controllingicon
about thespacing between the
installing holes. In order tomake load timing controllingicon
the controller havegood thermal Battery
dissipation, pleasespare10cm stop charging forbattery
above & below the controller.
charging for batteryat full speed
As shown as the right figure, connect the loads, battery and solar panels with the
controller in order. Pay attention to connect the loads, battery
and solar panels right. float charging forbattery
Plug the external thermal sensor into the interface of the thermal-sensor on the left normal working stateof system
of the controller. abnormal working stateof system
Disassemble: To avoid the accident, please dismantle the solar panels, battery, loads battery capacity display
from the controller in order.
Attention: Connecting the battery reversed will not damage the controller, but will battery icon
cause safety risk on your loads. 3 4

2 . Explanation of button function: 3.1 Battery voltage review

As shown as the right figure, the displaying number is the
:Interfaces circular toggling button. Use this button can realize
the toggling circularly
present battery voltage.
12.5 V

among the interfaces. The circular order is as follows: as shown asfigure 1.

: Parameter adjusting'+'+ button. Besides, under parameter review condition, press This interface is the main interface, and it shows the
this button for over 5 seconds, and all the parameters will recover to the ex-work charging & discharging state, battery capacity and
setting state. battery voltage.
:Parameter adjusting'-'button. Besides, at the main interface, this button can turn on
or turn off the load.
3.2 Load ON/OFF controlling
13.0 V
28 PV 20.0 A
LOAD
20.0 A PV 999 Ah At the battery voltage review 12.5 V
12.5 V

interface, you can press button

Battery voltage battery solar panels load discharging accumulative to turn on or turn off the load, while
(main interface) temperature generating current current generating AH
this button does not have this function at other interfaces.
LOAD O N
24 h PV OFF 13.8 V LOAD O N
12.6 V LOAD
OF F 1 0.7 V LO AD
990 Ah
3.3 Environmental temperature review
Be used for the temperature compensation when the 28
Load working ceasing charging recovery v oltage low voltage accumulative
state voltage protection poin discharging AH battery ceases charging.
3. Parameter review and setting: As shown as the right figure, the displaying number is the
After the controller electrifies right, it will enter into the displayinginterface of surrounding environmental temperature of the controller.
battery voltage. This interface is the main interface of thecontroller. P ress
button to go through the interfaces of the following parameters.the If interface
can be reset, press button for long( 5 seconds, and the number on the
3.4 Review the generating current of solar panels PV 27.0 A
As shown as the right figure, the displaying number is the
interface starts to flicker), then it enters into the setting
interface of this parameter.
After finishing setting, press button for long to exit the setting interface, and the generating current of solar panels.
number stops flickering.
5 6
3.5 The load current review 3.9 Review and setting recovering voltage for low voltage
LO AD
20.0 A
condition
As shown as the right the displaying number
is the load current. As shown as the right the displaying number is the
recovery number. After the controller enters into low voltage
3.6 Review and clearing the accumulative generating AH of solar panels protection state, and when the battery voltage recovers to
As shown as the right the displaying number is the be higher than the recovering voltage, then the controller
accumulating generating AH of solar panels will reconnect the load loop automatically.
PV Ah
At this interface, press button ( 5 seconds), and it can
clear accumulative generating AH.
At this interface,press button ( 5 seconds),thenumber
starts to and it means the controller enters into the
12.6
V

interface of setting the recovery voltage. Use button

3.7 Review and clearing load accumulative discharging AH to adjust this parameter. After setting, press
As shown as the right the displaying number is the LO AD
button ( 5 seconds) to exit this interface and the controller can storethis
accumulative discharging AH of loads. Ah setting number.
At this interface, press button ( 5 seconds), and it can
clear accumulative discharging AH. 3.10 Review and setting the voltage of ceasing charging
As shown as the right thedisplaying number is thevoltage of ceasing
3.8 Review and setting low voltage protection function
charging. When thebattery voltage reaches up to this voltage, the controlle r
As shown as the right the displaying number is the
protection voltage. And if the battery voltage is lower than
LO AD
OFF 1 0.7V will disconnect the chargingloop to prevent thebattery from o vercharging.
this voltage, the controller will disconnect the load loop to After th e battery voltage drops, the controller will reconnectthe chargingloop.
prevent the battery from over-discharging. At this interface, press button for long( 5 seconds),the number starts
At this interface, press button for long( 5 seconds),the to and it means the controllerenters into the interfaceof setting the
number starts to and it means the controller enters into the interfacesetting
of voltage ofceasing charging. Use button to adjust thisparameter.
the protection voltage. Use button to adjustthis parameter. After setting, pressbutton for long ( 5 se conds) to exit thi s
After setting, press button for long ( 5 seconds) to exit this interface
interface and the controllercan store this settingnumber.
and the controller can store this setting number.
7 8

3.11 Review and setting the load mode Overloading protection & disposal:
As shown as the right it is the reviewing surfaceof the If the screen shows as the right and thelight it
load mode. numbers represent load mode.
LO AD O N
24 h mean the current of the load loop is 1.2 times othe
f rated current
24h indicating normal mode, loads are under the condition within 3 seconds, and the controller is at overloading state.
After
of supplying power without breakdown; removing some loads, the controller will supply power to the
1h~23h indicating delayed mode of light control, loads start loads automatically within seconds, or you can press button to recover the
to supply power after darkand shun downafter working forthe delayed power supply compulsively.
setting hours
Short-circuit protection & disposal:
Oh indicating light control, loads start to supply power after dark and stop
working after dawn. If the screen shows as the right and thelight it
At this interface, press button for long( 5 seconds),the number tsarts to means there happens short-circuit in the load loop, and thentrol
co ler
and it means the controller enters into theinterface of setting the load is at short-circuit protection state. Please ch
eck whetherthe loads
modes. Use button to adjust this parameter.After setting, are damaged and whether the connecting cables are short-circuit.
press button for long( 5 seconds) to exit this interface and the controller After eliminating the breakdown, press button to recover the power supply
can store this setting number. for the loads.
Breakdown & disposal of solar panels:
Breakdown & disposal Sign means the controller do notdetect the existence of solar panels.
Please check whether the connecting with the solar panels is good
in condition, and
Low voltage protection & disposal: check whether the cables connecting the solaranels
p and the controller are i n
If the screen shows as the right it means thebattery open-circuit condition.
voltage is lower than the protection voltage. The controller Load impulsion breakdown:
enters into the low voltage protection state and the load loop
disconnects. Use the solar panels or charger to charge for the 10.6 V
If when you turn on the load, it means the starting impulsion current is
more than twice of the rated working current. Please restart the controller
for times.
battery. When battery voltage recovers to the protection
Other exceptional conditions: Please contact the distributor or manufacturer.
voltage, the controller will recover to supply power for load,
and enter into the working state. 9 10

11