Laser Diode Controller

LDC200C Series
Quick Reference

Full manual available at

www.thorlabs.com

2021
Version: 6.8
Date: 09-Mar-2021

Item No.: M0009-510-303-QS

Copyright © 2021 Thorlabs

 We aim to develop and produce the best solution for your application
in the field of optical measurement technique. To help us to live up to
your expectations and improve our products permanently we need
your ideas and suggestions. Therefore, please let us know about
possible criticism or ideas. We and our international partners are
looking forward to hearing from you.

Thorlabs GmbH

Attention
Paragraphs preceded by this symbol explain hazards that could
damage the instrument and the connected equipment or may cause
loss of data.

Note
This manual also contains "NOTES" and "HINTS" written in this form.

Please read this advice carefully!

© 2021 Thorlabs 1
LDC200C Series

1 General Information
As a part of Thorlabs Green Initiative, we aim to save paper and decided to offer electronic doc-
umentation to our products. This Quick Reference gives only a short introduction and states
safety and legal information.
The full manual can be downloaded in PDF format from the LDC200C Series product web site,
or simply by scanning the QR code:

Note
In order to prevent damages to the laser diode, it is recommended to mount the laser
into a suitable Thorlabs laser diode mount and connect it to the LDC200C Series using
the supplied Thorlabs CAB400 cable. This ensures the utmost protection of the laser di-
ode from damage by wrong connection.
1.1 Safety
Attention
The safety of any system incorporating the equipment is the responsibility of the assem-
bler of the system.
All statements regarding safety of operation and technical data in this instruction manual
will only apply when the unit is operated correctly as it was designed for.
The LDC200C Series must not be operated in explosion endangered environments!
Do not obstruct the air ventilation slots in the housing!
Do not remove covers!
Do not open the cabinet. There are no parts serviceable by the operator inside!
This precision device is only serviceable if properly packed into the complete original
packaging including the plastic foam sleeves. If necessary, ask for replacement pack-
aging.
Refer servicing to qualified personnel!
Only with written consent from Thorlabs may changes to single components be made or
components not supplied by Thorlabs be used.
Attention
Prior to applying power to the LDC200C Series, make sure that the protective conductor
of the 3 conductor mains power cord is correctly connected to the protective earth
ground contact of the socket outlet! Improper grounding can cause electric shock result-
ing in damage to your health or even death!
Ensure that the line voltage setting of the fuse holder at the rear panel agrees with your
local supply and that the corresponding fuses are inserted. If not, please change the line
voltage setting (see section Line voltage setting) and the mains fuses (see section Re-
placing the main fuses).

2 © 2021 Thorlabs
 1 General Information

To avoid risk of fire, only the appropriate fuses for the corresponding line voltage must
be used.
All modules must only be operated with proper shielded connection cables.
Attention
The following statement applies to the products covered in this manual, unless other-
wise specified herein. The statement for other products will appear in the respective ac-
companying documentation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules and meets all requirements of the Canadian
Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits
are designed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful in-
terference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
· Consult the dealer or an experienced radio/T.V. technician for help.

Users that change or modify the product described in this manual in a way not expressly
approved by Thorlabs (party responsible for compliance) could void the user’s authority
to operate the equipment.
Thorlabs GmbH is not responsible for any radio television interference caused by modi-
fications of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Thorlabs GmbH. The correction of interference
caused by such unauthorized modification, substitution or attachment will be the re-
sponsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all
optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.
Attention
Mobile telephones, cellular phones or other radio transmitters must not be used within
the range of three meters of this unit since the electromagnetic field intensity may then
exceed the maximum allowed disturbance values according to IEC61326-1.
This product has been tested and found complying with the limits according to IEC
61326-1 for using connection cables shorter than or equal to 3 meters (9.8 feet).
Warning
Laser modules can deliver up to several 100mW of even invisible laser radiation! When
operated incorrectly, this can cause severe damage to your eyes and health! Be ensure
to pay strict attention to the safety recommendations of the appropriate laser safety
class, as stated for the used light source.

© 2021 Thorlabs 3
LDC200C Series

Vous pouvez trouver les traductions françaises des paragraphes ayant trait à la sécurité
d'utilisation de ce produit sur le lien suivant:
https://www.thorlabs.com/_sd.cfm?fileName=15988-D03.pdf&partNumber=LDC202C
En outre, vous pouvez soit scanner le QR code, soit vous référer à la section "Docu-
ments" sur la page web du produit.

4 © 2021 Thorlabs
 2 Getting Started

2 Getting Started
Prior to operate a LDC200C Series controller, check if the set line voltage matches with your
local power supply and if the appropriate fuses are inserted.
The laser diode controller LDC2xxC operates at fixed line voltages of
100 V +15% / -10% ( 90 V … 115 V)
115 V +15% / -10% (104 V … 132 V)
230 V +15% / -10% (207 V … 264 V)
line frequency 50 … 60 Hz.
The line voltage setting can be changed from the rear without opening the unit.

1. Turn off the controller and disconnect the mains cable.

2. The fuse holder (R10) is located below the 3-pole power
connector of the mains jack (R9). Release the fuse holder
by pressing its plastic retainers with the aid of a small
screwdriver. The retainers are located on the right and left
side of the holder and must be pressed towards the center.
3. Unplug the white line voltage switch/indicator (R8, con-
taining the left fuse) from the fuse holder (R10), rotate it
until the appropriate voltage marking (100V, 115V, or
230V) is on target for the cutout (R12) of the fuse holder,
and plug it back into the fuse holder. Press in the fuse
holder until locked on both sides. The appropriate line
voltage marking must be visible in the cutout (R12) of the fuse holder.

Attention
If you have changed to or from 230 V, also change the mains fuses to the correct value given
below:
Fuse types
LDC200VC, LDC201CU, LDC202C, LDC205C, LDC210C, and LDC220C:
100 V 500 mA, time-lag, 250V T0.5A250V
115 V 500 mA, time-lag, 250V T0.5A250V
230 V 250 mA, time-lag, 250V T0.25A250V

LDC240C:
100 V 800 mA, time-lag, 250V T0.8A250V
115 V 800 mA, time-lag, 250V T0.8A250V
230 V 400 mA, time-lag, 250V T0.4A250V

All fuses must meet IEC specification 60127-2/III, time characteristic: time-lag (T), 250V AC,
size 5 x 20 mm.
Connect the unit to the power line using the supplied cable. Turn the unit on by pressing the
line switch.
If required, the chassis ground can be connected to ground potential via the connector jack
(R5). The ground pin of the laser diode is internally connected to chassis ground.

© 2021 Thorlabs 5
LDC200C Series

Please see the full manual for detailed operating instructions and technical data. This manual
can be downloaded from our web site, or simply by scanning the QR code:

6 © 2021 Thorlabs
 3 Appendix

3 Appendix
3.1 Declaration of Conformity

This product was tested for and complies with the following standards:
· CAN/CSA-C22.2 No. 61010-1-04
· ANSI/UL 61010-1-2004

© 2021 Thorlabs 7
LDC200C Series

3.2 Environmental Conditions

Mains Supply Overvoltage Category II (Cat II)

Relative Humidity Max. 80% up to 31 °C;
decreasing to 50% at 40 °C
Pollution Degree (Indoor use only) 2
Operation Altitude <2000 m
Operating Temperature Range (non condensing) 0°C to 40°C

3.3 Warranty
Thorlabs warrants material and production of the LDC200C Series for a period of 24 months
starting with the date of shipment. During this warranty period Thorlabs will see to defaults by
repair or by exchange if these are entitled to warranty.
For warranty repairs or service the unit must be sent back to Thorlabs. The customer will carry
the shipping costs to Thorlabs, in case of warranty repairs Thorlabs will carry the shipping costs
back to the customer.
If no warranty repair is applicable the customer also has to carry the costs for back shipment.
In case of shipment from outside EU duties, taxes etc. which should arise have to be carried by
the customer.
Thorlabs warrants the hard- and/or software determined by Thorlabs for this unit to operate
fault-free provided that they are handled according to our requirements. However, Thorlabs
does not warrant a fault free and uninterrupted operation of the unit, of the software or firmware
for special applications nor this instruction manual to be error free. Thorlabs is not liable for
consequential damages.
Restriction of Warranty
The warranty mentioned before does not cover errors and defects being the result of improper
treatment, software or interface not supplied by us, modification, misuse or operation outside
the defined ambient stated by us or unauthorized maintenance.
Further claims will not be consented to and will not be acknowledged. Thorlabs does explicitly
not warrant the usability or the economical use for certain cases of application.
Thorlabs reserves the right to change this instruction manual or the technical data of the de-
scribed unit at any time.

8 © 2021 Thorlabs
 3 Appendix

3.4 Copyright and Exclusion of Liability

Thorlabs has taken every possible care in preparing this document. We however assume no li-
ability for the content, completeness or quality of the information contained therein. The content
of this document is regularly updated and adapted to reflect the current status of the hardware
and/or software. We furthermore do not guarantee that this product will function without errors,
even if the stated specifications are adhered to.
Under no circumstances can we guarantee that a particular objective can be achieved with the
purchase of this product.
Insofar as permitted under statutory regulations, we assume no liability for direct damage, indir-
ect damage or damages suffered by third parties resulting from the purchase of this product. In
no event shall any liability exceed the purchase price of the product.
Please note that the content of this document is neither part of any previous or existing agree-
ment, promise, representation or legal relationship, nor an alteration or amendment thereof. All
obligations of Thorlabs result from the respective contract of sale, which also includes the com-
plete and exclusively applicable warranty regulations. These contractual warranty regulations
are neither extended nor limited by the information contained in this document. Should you re-
quire further information on this product, or encounter specific problems that are not discussed
in sufficient detail in the document, please contact your local Thorlabs dealer or system in-
staller.
All rights reserved. This document may not be reproduced, transmitted or translated to another
language, either as a whole or in parts, without the prior written permission of Thorlabs.
Copyright © Thorlabs 2021. All rights reserved.

© 2021 Thorlabs 9
LDC200C Series

3.5 Thorlabs Worldwide Contacts and WEEE Policy

For technical support or sales inquiries, please visit us at www.thorlabs.com/contact for our
most up-to-date contact information.

USA, Canada, and South America UK and Ireland

Thorlabs, Inc. Thorlabs Ltd.
[email protected] [email protected]
[email protected] [email protected]

Europe Scandinavia
Thorlabs GmbH Thorlabs Sweden AB
[email protected] 10 [email protected]

France Brazil
Thorlabs SAS Thorlabs Vendas de Fotônicos Ltda.
[email protected] 10 [email protected]

Japan China
Thorlabs Japan, Inc. Thorlabs China
[email protected] [email protected]

10 © 2021 Thorlabs
 3 Appendix

Manufacturer Address Europe EU-Importer Address

Thorlabs GmbH Thorlabs GmbH
Münchner Weg 1 Münchner Weg 1
85232 Bergkirchen 85232 Bergkirchen
Germany Germany
Tel: +49-8131-5956-0 Tel: +49-8131-5956-0
Fax: +49-8131-5956-99 Fax: +49-8131-5956-99
www.thorlabs.de www.thorlabs.de
Email: [email protected] Email: [email protected]

Thorlabs 'End of Life' Policy (WEEE)

Thorlabs verifies our compliance with the WEEE (Waste Electrical and Electronic Equip-
ment) directive of the European Community and the corresponding national laws. Ac-
cordingly, all end users in the EC may return “end of life” Annex I category electrical and
electronic equipment sold after August 13, 2005 to Thorlabs, without incurring disposal
charges. Eligible units are marked with the crossed out “wheelie bin” logo (see right),
were sold to and are currently owned by a company or institute within the EC, and are
not dissembled or contaminated. Contact Thorlabs for more information. Waste treat-
ment is your own responsibility. “End of life” units must be returned to Thorlabs or
handed to a company specializing in waste recovery. Do not dispose of the unit in a litter
bin or at a public waste disposal site.

© 2021 Thorlabs 11
www.thorlabs.com