Scribd
Upload
12 views

BTCS403 End Sem With CO

Uploaded by

everlovingmansi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
12 views

BTCS403 End Sem With CO

Uploaded by

everlovingmansi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Enrollment No:_____________

GSFC UNIVERSITY
SCHOOL OF TECHNOLOGY
B.Tech. Regular End Sem Examination Even Session 2022-23
Semester: VI Date: 16/06/2023
Subject Code: BTCS403 Time: 10:00 am – 12:00 pm
Subject Name: Microprocessor & Interfacing Total Marks: 40
Instructions
1. Attempt all questions.

Course Outcomes (CO):


CO1: To make student understand about basic components of micro-processor.
CO2: To aware students about 8085 architectures.
CO3: To familiar about assembly language.
CO4: To give brief knowledge about an architecture of 8086.
CO5: To inculcate students for ARM processor.

Q.N. Questions Marks CO


Q.1 MCQs / fill in the blanks. It should be covered from the entire syllabus (08)
a. The microprocessor of a computer can operate on any information if it is present in (01) CO1
______________ only.
b. Which of the following addressing method does the instruction, MOV AX, [BX] (01) CO4
represent?
a) register indirect addressing mode b) direct addressing mode
c) register addressing mode d) register relative addressing mode
c. Which of the following is not true about the address bus? (01) CO2
a) It consists of control PIN 21 to 28 b) It is a bidirectional bus
c) It is 16 bits in length d) Lower address bus lines (AD0 –
AD7) are called “Line number”
d. Which of the following is a property of RST 7.5 interrupt? (01) CO2
a) It is a non-maskable interrupt b) It has 3rd highest priority
c) It uses level-triggered signal d) Its vectored address is 003C H
e. What will be the value in accumulator, for the given 8085 program below? (01) CO3
MVI C,7FH
MVI B, 3EH
MOV A, B
RLC
RLC
ANI 7FH
HLT
a) 78H b) 75H c) 68H d) 65H
f. What is the content of accumulator of 8085 microprocessor after the execution of (01) CO3
XRI F0 instruction?
a) Clear the lower four bits of the accumulator in 8085.
b) Complement the upper four bits of the accumulator in 8085.
c) Clear the upper four bits of the accumulator in 8085.
d) Complement the lower four bits of the accumulator in 8085.
g. When a microprocessor reaches a stop instruction it responds back in _______ (01) CO1
format to the ports output.
h. After the execution of the given statements, determine the status of PSW. (01) CO3
MVI A, 0BFH
ADI A, 1BH
a) 11010001 b) 01011011 c) 01000000 d) 10100001

Q.2 It contain questions from first two units. (08)

Page 1 of 4
Q.N. Questions Marks CO
a. Explain following pins of an 8085 microprocessor in brief: 1. ALE 2. X1/X2 3. DEN (04) CO2
b. 4. MN/MX
Draw the timing diagram of MOV M, D instruction of an 8085 microprocessor. (04) CO1
OR
a. Write an 8085-assembly language program to arrange the following numbers in (04) CO3
ascending order: 29H, 47H, 06H, 03H, 17H.
b. Explain Following: Machine cycle, DAA, RRC, STC (04) CO3

Q.3 It contain questions from next two units. (08)


a. Consider the following 8085 assembly language instructions: (04) CO4
LXI D, 1234H
NEXT: DCX D
MOV A, E
ORA D
JNZ NEXT
What amount of delay is generated if the crystal frequency is 4 MHz?
b. List and explain the segment registers of 8086 microprocessor. (04) CO4
OR
a. Explain the real mode and protected mode of the 80286 microprocessors. (04) CO4
b. Explain the paging mechanism in an 80386 microprocessor. (04) CO4

Q.4 It contain question/s from all units. (12)


a. Draw the block diagram of the programmable peripheral interface 8255A. Also (12) CO5
explain control register, control word and different modes of 8255A in detail.
OR
a. Draw and explain the block diagram of the programmable interrupt controller (06) CO1
8259A.
b. What are interrupts? List and explain the interrupt available in microprocessor 8085? (06) CO2

Q.5 Only one question related to current trend in the subject. (04)
a. Draw and explain logical block diagram of ARM 7 architecture CO5

Course Outcome CO1 CO2 CO3 CO4 CO5 Total Marks

Marks Weightage 18 18 16 25 23
12 12 11 17 16 40
in Question Paper % % % % %

Page 2 of 4
Draft Circular:

Preamble:

GSFC University evaluates the academic performance of its students through various
examinations, including Mid Semester Examination, Continuous Evaluation, and End
Semester Examination, every semester. In accordance with the guidelines and
recommendations of National Assessment and Accreditation Council (NAAC), National
Education Policy 2020 (NEP 2020), University Grants Commission (UGC), and All India
Council for Technical Education (AICTE), the university has decided to adopt Outcome
Based Education (OBE) as a framework for assessing and evaluating the academic
progress of students.

Decision:

It is proposed to incorporate the Course Outcome based evaluation from the current
Even session 2022-23 onwards. The guidelines for the implementation are as follows:

1. All the concerned Paper Setter are required to re-submit the Question Paper for
(Semester-II & IV) along with defined Course Outcome (COs) as per attached
format.
2. After completion of Assessment in particular subject(s), concerned Examiners are
required to fill the evaluated marks in the given excel sheet and upload the Excel
sheet into the shared Google Drive of respective School.

Page 3 of 4
3. Examiners can bring their laptop into Examination Division for preparing the Excel
Sheet.
4. Respective Schools will find the evaluated Excel Sheet in their Google Drive for
record and further submission to any such inspection body whenever required.

Page 4 of 4

You might also like