1. Query commands are used only to request parameters.

NO Function Command

VERSION#
1 Query the version.
VERSION,BUILD#

2 Request for parameters. PARAM#

3 Request for brief parameters SCXSZ#

4 Check the statuses. STATUS#

Check the network parameters

5 such as GPRS state, APN, server GPRSSET#
address, and URL.

6 Enable device self-check. CHECK#

Request for the latitude and

7 WHERE#
longitude of the device.
 Request for the latitude and
7 WHERE#
longitude of the device.

8 Request for a location link. URL#

9 DW#
Request for the location of the
10 POSITION#
device (SMS only)
11 Check the lock status of the 123 #
12 current domain name of the QLOCKIP#
device.
ers.

Example Reply Explanation

[VERSION]ET310_TEST_V01_20200520_0900
[BUILD]20200520_0900

IMEI:352273017386340;SOS:123 , ,;CENTER: ;TimeZone:E,8,0

(AUTO);

CMnet,,;10,10;180;E8,0;1,test.topstargps.com,11139;,,;;10;10;1;
Battery:3.85V,NORMAL; GPRS:Link Up GSM Signal Level:Low;
GPS:OFF; ACC:OFF; Defense:ON;

GPRS,ON;Currently use APN:CMnet,,;APN Auto

set:OFF;SERVER,1,test.topstargps.com,11139;URL,http://maps.go
ogle.com/maps?q=

IMEI:;
VERSION:ET310_TEST_V01_20200520_1425;
SERVER:1,test.topstargps.com,11139;
BSERVER:0,0.0.0.0,0;
GET IP:120.234.211.126;
APN:CMnet,,;
CSQ: [4G]13;
GPRS:1;
GPS:OFF;
BDS:OFF;
BAT:3.79;
POWER:0.00;
TIMER:10,10;
SOS NUM:,,;
CENTER:,,;
CELL:NB-Iot,searching(1);
IMSI:460044335609859;
ICCID:898604231919C2690159;
EURL:http://maps.google.com/maps?q=;

The device is already networked and fixed a position: Current

position!
Lat:N23.111507,Lon:E114.409004,Course:255.68,Speed:0.00Km/
h,DateTime:2020-05-22 10:28:04
 The device is already networked and fixed a position: Current
position!
Lat:N23.111507,Lon:E114.409004,Course:255.68,Speed:0.00Km/
h,DateTime:2020-05-22 10:28:04

The device is already networked and fixed a position: <05-22

10:53>
http://maps.google.com/maps?q=N23.111712,E114.409264

The device is already networked and fixed a position: 26m

northwest of Investment Building, 5th Floor, 6 Yunshan West Rd,
Huicheng District, Huizhou, Guangdong.
http://maps.google.com/maps?q=N23.111605,E114.409409
The device is neither networked nor positioned: Failed to get
location, please try again!
QLOCKIP,0(0:unlock,1:lock)
2. Execute commands are required to be executed immediately.

NO Function Command

1 Restore to factory FACTORY#

2 Reboot RESET#

3 Modify the command password. PASSWORD,P1,P2#

4 Upload the LBS data by roll call. LBS#

5 Activate the GNSS module of the device. GPSON,T#

Query the information of invisible satellites by roll

6 CXSV#
call.
7 Query the ICCID by roll call. ICCID#
8 Request for the IMSI IMSI#
9 Lock the IP or the domain name. LOCKIP#
10 Cold start the GNSS module. GPSCOLD#
11 Clear the backup data. CLEAR#
12 Dismiss the defense. DSRESET#
Example Reply Explanation
FACTORY set OK! The terminal will
restart after 30s!

The terminal will restart after 20 seconds!

PASSWORD set OK! P1: Old password;P2: New password.

LBS set OK!

T: This specifies how long will the GNSS

module run after being activated. The range is
5-300 minutes.
GPSON set OK Note: If no parameter is carried in this
command, the GNSS module run duration will
be 5 minutes, that is, the default value of T
(5#).
CXSV set OK!
ICCID: 898604231919C2690159
IMSI:460044335609859
LOCKIP set OK!
GPSCOLD set OK!
CLEAR set OK!
DSRESET set OK!
3. Set and query commands are used to set as well as request for parameters.
For query-only commands, a pound key (#) will be added to the command end.
NO Function

1 Set APN

2 Set automatic APN

3 Set GMT parameter

4 Set automatic GMT

5
Set server parameters
6 Edit URL
7 GPRS switch
Set the interval for sending heartbeat packets
8
and check the setting.
9 Set the time interval to upload GNSS data
10 Set the distance interval to upload GNSS data
11 Set the parameters to upload additional fixes
Set the parameters to upload a position fix when
12
the ACC
Set state changes
the parameters to send the GNSS data in
13
batch
14 Force upload location data switch
15 Set the state of AGPS
16 Set the parameters of the static data filter
17 Set the parameters to upload LBS data
18 Mileage statistics
Set the visible satellites information upload
19
parameters
Set the time and condition for the sensor to
20
activate
Set the GNSS to
the parameters module
upload the voltage data of
21
external power
22 Set the LED
23 Set the petrol/electricity control
24 Set the defense mode
25 Set the defense parameters
26 Set the defense manually.

27 Disable the defense manually.

28 Set the dialing times

29 Set the parameters of ACC alert.
30 Set sensitivity of SENSOR
Set the parameters to upload the last location
31
when the sensor detects the vehicle keeps static
32 Set the parameters of the vibrating alert
33 Set the parameters of the power-cut alert

34 Set the parameters of the low battery alert

Set the parameters of the low external power
35
alert
36 Set the vehicle towing alert
37 Set the parameters of the speeding alert

38 Set the parameters of the multi-geofence alert

Set the parameters of the abrupt speed change

39 Set the parameters of the collision alert
alert
40 Set the parametersthe
(Definition:When of the sharp intensity
collision corneringreaches
alert
41 the preset intensity, it is determined as a
42 collision event, andofthe
Set the parameters thecollision
rolloveralarm
alert is
43 uploaded to the platform.)
Set the parameters of the tamper alert

44 Set SOS numbers.

Set the center number and check the setting.

45 Set the center number and check the setting.
Set the center number and check the setting.
46 Set the password feature
47 Set the SMS transparent transmission server
48 Forward via SMS. of the device to enter
Set the parameters
49 airplane mode when the low voltage protection
alert is triggered.
50 Monitor

51 Mutual Communication

52 Bluetooth open
53 Set permissions scheme for phone numbers
54 Set permissions for SOS numbers
55 Set I/O1
56 Set I/O2
57 Inputmode1 alert【eg：Door status check】
 58 Inputmode2 alert【eg：Door status check】
59 Outmode set
60 ADC voltage alarm
61 Variable IO detection trigger mode
62 Side door open alarm
63

64 Incoming call permission control

65 Incoming call delay answering control

66 buzzer mode of buzzer_overtime
67 buzzer mode of buzzer_overspeed
68 Engine judgment

69 Engine voltage to define the engine status

Version 1.x 70 Fuel sensor set

and 3.x/more
version 3.1 71 Oil sensor upload interval control
and so on 72 Oil sense refueling/oil stealing alarm control
s well as request for parameters.
will be added to the command end.
Command Example Reply

APN,apnname#
OR APN,apnname,user,pwd#

APN#

ASETAPN,SW#

ASETAPN#

GMT,A,B,C#
GMT#
ASETGMT,SW#
SERVER,mode,domainName/IP,port,protocol#
SERVER#
EURL,URL#
GPRSON,SW#
HBT,T1,T2#
TIMER,T1,T2#
DISTANCE,D#
ANGLEREP,SW,A,T#
ACCREP, SW#
BATCH,SW,N#
GPSDUP, SW#
AGPS, SW#
SF,SW,D#
LBSON,SW,T1,T2#
MILEAGE, SW,L,K#
SV,SW,T1,T2#
SENDS,T1,T2,N#
ADT,SW,T#
LEDSW,SW#
RELAY,M,V#
DEFMODE,M#
DEFENSE,T#
111 #

000 #

CALL,N#
ACCALM,SW,M,T,N#
LEVEL,M#
STATICREP,SW,T,V,N#
SENALM,SW,M,N,T1,T2,T3#
POWERALM,SW,M,T1,T2,T3#

BATALM,SW,M#
EXBATALM,SW,M,V1,V2,T#
MOVING,SW,M,R#
SPEED,SW,M,V,T#

Circular geofence: GFENCE,N,SW,0, LNG,LAT,R,X,M#

Rectangular geofence: GFENCE,N,SW,1,

LNG1,LAT1,LNG2,LAT2,X,M#
SPEEDCHECK,SW,M ,T,V1,V2#
SWERVE, SW,M,A,V,T#
COLLIDE,SW,M,N,T1,T2,V#
ROLLOVER,SW,M,N,T#
PULLALM,SW,M,N,T#
SOS,A,phone number 1,phone number 2,phone number 3#
SOS,D,sequence number 1, sequence number 2,sequence
number 3#
SOS,D,phone number#
SOS#
CENTER,A,NUM#
CENTER,D#
CENTER#
PWDSW,SW#
SMSTC,NUM#
FW,A,B#
FLYCUT,SW#

JT,A#

DIAL,A,M#

BLETOOL, <SW>#
PERMIT,<M>#
SOSPERMIT,<M>[,Y]#
IOMODE1,<M>#
IOMODE2,<M>#
INPUT1ALM,SW,M, C,T#
INPUT2ALM,SW,M, C,T#
OUTPUTSWITCH,SW,X,[T]#
ADC1ALM,SW[,M][,VH][,VL]#
iotrig_set,<M>,<A> #
DOORALM,SW,M #
SMSINPUT,[A],[B]#

MONPERMIT,<A> #

MONDELAY,<A> #
buzzer_overtime, <SW>[,A] [,B]#
buzzer_overspeed, <SW>[,A] [,B]#
ENGALM,<SW>[,M] #

ENG,<SW>[,V][,T]#

UL212SW,SW#
NTTOILTIME [,A] [,B]#
UL212OILALM [,A] [,B] [,C]#
Explanation

Close automatic APN and set by yourself.

Check the current APN parameters.

SW=ON/OFF;
ON: open automatic APN;
OFF: close automatic APN.

Check automatic APN status

A:E or W；"E" means eastern time zone,"W" means western time zone；default:E
B:0～12；time
Check the current zone
timedefault:8
zone parameters
eg: SERVER,1,gpsdev.tracksolid.com,21100,0#
SW: SERVER,0,47.89.58.215,21100,0#
ON or OFF.
The default value of “SW” is ON.
mode = 1 means set with domain name
mode
Check=the 0 means
currentset withparameters
sever ip address
protocol
URL: It refers to the locationserver
= 0 means connect querywith
link.TCP protocol
protocol = 1 means connect server with UDP protocol(Not use for now)
SW: ON or OFF.
The
T1:the default value
interval of “SW”
to upload is ON. heartbeat packets, ranging from 1 to 10 minutes.
ACC_ON
T2: the interval to upload ACC_OFF
T1 ranges 1~18000 or 0(seconds),upload heartbeat packets,
interval whenranging
ACC ON,from 1 to 10no
0 means minutes.
upload,default
is 10;
D ranges 50~10000 or 0(meters),distance interval,0 means no upload,default is 300; If set
distance,
SW:ON or timer
OFF;will not work.
A: theON
SW: angle threshold, 5~180 degrees;
or OFF.
The defaultOFF.
SW:ONor value of “SW” is ON.
N:
SW: theON pieces of data in a batch, 1~10 pieces.
or OFF.
Note:ON
SW: Theordefault
OFF. value of “SW” is OFF.
Note:
SW: ON or OFF. value of “SW” is ON.
The default
D:
SW: theON maximum
or OFF;distance interval to enable static data filter, 100~10,000 meters.
T1: the
SW: ONinterval
or OFF; to upload the data, 10~3,600 seconds;
L:
SW: ON or OFF; initial value of the mileage reading, ranging from 0 to 999,999 km. If L is set
It specifies the
to
T1:“0”,
T1: It itupload
meanstime
thespecifies to clear
how longthe
interval,
willmileage
5the data.seconds;
~ 18,000
GNSS module run after being activated, ranging from 0 to
300 minutes;
SW: ON or OFF;
T: It specifies
SW:ON or OFF;the upload interval, ranging from 5 to 3,600 seconds.
Note:
M: The default
It indicates thevalue is OFF.
fuel and power supply status, where “0” means the fuel and power supply is
connected and “1” means
M: It indicates the defense mode, the fuel where
and power supplytoisautomatic
“0” refers cut. mode and “1” manual mode.
Note: The default value is “0”.
T: It specifies the delay to enable the defense mode, ranging from 1 to 60 minutes.
Note: The defense mode is disabled by default. The default value of “T” is “3”.

N=1–3; default: 3; This applies to all emergency calls.

SW: ON or OFF;
M=0/1 ,0=GPRS;
M: It specifies how1=SMS+GPRS;
sensitive the sensor is, ranging from 1 to 5. The default value is “2”.
SW:ON or OFF;
T: It specifies
SW: ON/OFF for how long the vehicle remains in stop will the device upload the last position
fix, ranging 0=GPRS,
M=0/1/2/3 from 10 to1=SMS+GPRS,
300 seconds; 2=GPRS+SMS+Call, 3=GPRS+Call.
SW: ON or OFF;
M=0/1/2/3 0=GPRS, 1=SMS+GPRS, 2=GPRS+SMS+Call, 3=GPRS+Call.
T1: It specifies how long will the power-cut detection last when the device is in ACC ON or
OFF state, ranging from 1 to 3,600 seconds;
T2: It specifies the interval between two alerts, during which period the device will stop
generating power-cut alert if it detects the power has reconnected. The value ranges from 0 to
3,600 seconds.
T3: It specifies the alert silent time, which means the device will not upload power-cut alerts
during this period. The value ranges from 0 to 3,600 seconds, where “0” means there is no
silent time, that is, the parameter “T3” is invalid.
Note: The default values are “ON”, “1”, “10”, “10”, and “0” respectively (ON,1,10,10,0#).

SW: ON or OFF;
M=0/1
SW: ON,0=GPRS;
or OFF; 1=SMS+GPRS;
M=0/1
SW: ON or OFF; 1=SMS+GPRS;
,0=GPRS;
M=0/1/2/3
SW: ON or0=GPRS,
OFF; 1=SMS+GPRS, 2=GPRS+SMS+Call, 3=GPRS+Call.
M=0/1 ,0=GPRS; 1=SMS+GPRS;
Circular geofence setting: N: It refers to the geofence number, ranging from 1 to 5;
SW: ON or OFF;
LNG: It indicates longitude of the center coordinate;
LAT: It indicates the latitude of the center coordinate;
R: It indicates the radius of the geofence, whose unit is a hundred meter;
X: It specifies what types of geofence alerts will be uploaded, where “IN” refers to entering
geofence alert, “OUT” leaving geofence alert, and null entering and leaving geofence alerts;
M=0/1 ,0=GPRS; 1=SMS+GPRS;
Note: The third parameter is fixed at “0”, which means it is a circular geofence.

Rectangular geofence setting:

Circular
SW: ONgeofence
or OFF; setting: N: It refers to the geofence number, ranging from 1 to 5;
M=0/1ON
SW: ,0=GPRS;
or OFF; 1=SMS+GPRS;
M=0/1
SW:ON or OFF; 1=SMS+GPRS;
,0=GPRS;
M=0/1
SW: ON,0=GPRS;
or OFF; 1=SMS+GPRS;
M=0/1ON
SW: ,0=GPRS;
or OFF; 1=SMS+GPRS;
M=0/1
NUM1: It refers to1=SMS+GPRS;
,0=GPRS; the first SOS number;
NUM2:
delete byItsequence
refers to the second SOS number;
delete by phonenumber
query sos factors
Add center numbers.
Delete center numbers.
Check the center number.
SW: ON or OFF.
The
“NUM”default value“0”
is either is “OFF”
or “1”,(OFF#).
where “0” means to disable SMS transparent transmission and “1”
to enable SMS transparent transmission.
A: the phone number that receives the forwarded information;
B: the forwarded
SW:ON or OFF. information.
The default value is “OFF” (OFF#).
A:phone number

A:phone number
M:phone call Times 1-10
SW: ON/OFF. The default value is “OFF”
M:
M: It
It indicates
indicates the
the permissions
permissions scheme,
scheme, whose
whose value
value is
is either
either "0"
"0" or
or "1".
"1";
Note: The default value is "0" (0#).
Y: It specifies the polling method of alert packets, where "0" means to send alert packets to the
IO1
first configuration
valid SOS numbercommand: IOMODE1,<M>#
and "1" means to send alert packets to all SOS numbers.
SW:
M:
IO2
Note: switch,
input ON/OFF;
0:configuration
mode;
The default 1: output
are mode;
command:
values "0" and2:"1"
buzzer
IOMODE2,<M># mode;
(0,1#).
M: Alarm
Default: 0 reporting method, 0 only GPRS,
M: 0: input mode; 1: output mode; 2: buzzer mode;1 SMS+GPRS;
C: detection
Default: 0 mode, 0: trigger alarm in active state; 1: trigger alarm in inactive state; 2: trigger
alarm in both active and inactive states
T: Active state duration, (1s to 60s)
Default: (OFF,0,0,10#)
SW: switch, ON/OFF;
M: Alarm reporting method, 0 only GPRS, 1 SMS+GPRS;
C:
ADCdetection
voltagemode,
alarm 0: trigger alarm
command: in active state; 1: trigger alarm in inactive state; 2: trigger
ADC1ALM,SW[,M][,VH][,VL]#
SW:
alarmON/OFF.
in both ON: Continuous
active and inactive open-drain
states output; OFF: Stop open-drain output;
SW:
X: switch,
output pinON/OFF;
T:
M: Active state
Alarmdrain duration, (1s to
reporting 60s) GPRS, 1 SMS + GPRS;
Variable
T: Open
Default: IO outputmethod,
detection
(OFF,0,0,10#) trigger 0mode
duration only
(1s tocontrol
10s) command: iotrig_set,<M>,<A> #
VH:IOadc
M: voltage
port optionhigh
1: IOalarm
portvalue,
1 2: IOsetting
port 2range: 0to5V, setting concentration 0.1V
SW:
VL: switch,
adc
A: Trigger ON/OFF;
voltage
mode low alarm value,
0: Negative setting
trigger range: trigger
1: Positive 0to5V, setting concentration 0.1V
M: Alarm reporting
Description: Default method,
setting 0 only GPRS, 1 SMS+GPRS;
(ADC1ALM:OFF,0,4.5,1.0#)
Description: Default value (1,0#) (2,0#) 2 SMS+GPRS+CALL
Default: (OFF,1#)

A: Answer method:
0: No answering 1: Only the center number is allowed to answer 2: SOS number and center
number are allowed to answer (default) 3: Any number can answer:
Description: Default value (2#)
Overtime alarm buzzer reminder command: buzzer_overtime, <SW>[,A] [,B]#
SW: switch,
A: Delay timeON/OFF;
(5-20 seconds)
A: 1 is
Overspeedcontinuous
Description:alarm reminder,
buzzer
Default 2 is intermittent
reminder
value (10#) command: reminder (sound for<SW>[,A]
buzzer_overspeed, 2000ms and then silence for
[,B]#
6000ms)
SW: switch, ON/OFF;
B:
A: Timeout period reminder,
1 is continuous
SW：ON/OFF； for continuous reminders (1-60
2 is intermittent minutes)
reminder (500ms beep and 3000ms silence)
Description:
B: Timeout
M：0 Default value
periodSMS+GPRS；
:GPRS，1 (ON,1,5#)
for continuous reminders (1-60 minutes)
Description:
Default Default value (ON,1,5#)
value（ON,0#）
SW: switch, ON/OFF;
V: voltage constant, setting range 90-360, unit 0.1V;
T: time value, setting range 0-60, unit second;
Description: Default value (ON,128,10#).
SW:ON/OFF
A: Detect
A: 10~600alarm default
(seconds) is off
ACC
content ON detect
0: Not detection time
alarm 1: Oil stealing alarm 2: Refueling alarm 3 Oil
B:
stealing+refueling alarm OFF detection time
10~600 (seconds) ACC
Description: Defaultmethod,
B: Alarm reporting value (60,60#)
0 only GPRS, 1 SMS+GPRS;
C: Alarm silence time (2-60 minutes)
Description: Default value (0,0,2#)