Scribd
Upload
2K views

Sway Bar Calculations

The document explains two methods for calculating the effective spring rate of a sway bar: 1) Combining the deflection of each bending segment in series, and 2) Adding the deflection from bending to the deflection from torsion. Both methods result in the same equation used in Puhn's book. The spring rate depends on the material properties of the bar, the length of the arms, and whether it is solid or hollow. Shorter arm lengths increase the stiffness of the sway bar.

Uploaded by

Mark van Buuren
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views

Sway Bar Calculations

The document explains two methods for calculating the effective spring rate of a sway bar: 1) Combining the deflection of each bending segment in series, and 2) Adding the deflection from bending to the deflection from torsion. Both methods result in the same equation used in Puhn's book. The spring rate depends on the material properties of the bar, the length of the arms, and whether it is solid or hollow. Shorter arm lengths increase the stiffness of the sway bar.

Uploaded by

Mark van Buuren
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Effective Spring Rate in Sway Bars:

I am sure that many of you have seen the Equation below from Fred Puhns book How to Make Your Car Handle. The following pages of diagrams and equations are my attempt to explain why this equation gives you the effective spring rate at the end of the arm where the end link attaches to the sway bar. The equation from Puhns book is only good for spring rate in , and it assumes generic properties for steel. If that is good enough for you, use his equation; It works. If you would like to know more about why that equation will give you a good number for the effective spring rate of a sway bar, keep reading.
lbf in

Figure 1: basic sway bar dimensions

Solve for spring rate as Force per deflection:

We can solve for the effective spring rate by using the individual spring rates for each segment of the bar and combining them in series, or we can add the deflection due to bending of the ends to the deflection at the ends due to torsion in the bar and solve for the effective spring rate.

Combine the deflections for each segment and solve the spring rate:
The total displacement is: * We use 2 xs the deflection for bending because the sway bar has 2 segments in bending (each arm)

By substituting common values for steel in psi and assuming that the bar is solid (i.e. d=0) we get the following:

Finally if we divide each term by 141.37154 (equivalent to multiplying by 1 sorry if that is obvious) we get the equation used in Puhns book. I really have no idea why

Combine the spring rate of each segment in series and calculate the effective spring rate

* We use 2 xs the deflection for bending because the sway bar has 2 segments in bending (each arm) By substituting common values for steel in psi and assuming that the bar is solid (i.e. d=0) we get the following:

Finally if we divide each term by 141.37154 (equivalent to multiplying by 1 sorry if that is obvious) we get the equation used in Puhns book. I really have no idea why

Using Either Method we get the same answer. The general equations that have not assumed material properties can be used for any system of consistent units. Typical values for the Elastic Modulus of steel (Esteel) can range from 27,000,000 30,000,000 psi (190-210 MPa) Typical values for the Shear Modulus of steel (Gsteel) can range from 10,400,000-12,000,000 psi (75000-80000 MPa) Obviously using different number will change the calculated values slightly. Many of the aftermarket front sway bars come with multiple end link mounting points. Using the hole which gives the shortest arm length will make the sway bar stiffer, and alternately using the hole which gives the longest arm will make the sway bar softer. In summary, the torsional stiffness of a sway bar calculated as a function of the applied force and the deflection at the end links comes from the torsional stiffness of the straight section and the bending stiffness of each arm.

Michael J. Iacchei Version 1.0 May 2010

You might also like