Technical Data

Sheet

CIKOproof 2K-25
Flexible Cementitious waterproof Slurry.

Description  Roof and terraces waterproofing under tiles or

CIKOproof 2K-25, acrylic modified cement insulation systems.
based waterproof coating recommended for  Waterproofing of Planter Boxes.
horizontal and vertical applications on
concrete, mortar and clay / cement block Physical Properties
masonry surface. Two component system
CIKOproof 2K-25 is a two component Form Part-A : Powder
waterproofing system consisting of Part-A Part-B : Liquid
which is a blend of select cement type, graded Colour Grey or white
fine aggregates, dispersing agent etc. and 0
Part-B which is an aqueous dispersion of Pot life @ 25 C 45-60 minutes
adhesion enhancing polymer in the form of Mixed Density 2.0 ± 0.05 g/cm³
liquid component. CIKOproof 2K-25 penetrates Tensile Strength ASTM 2
into the pores of the substrate and seals it to ≥5 N/mm
D412 @ 14 days
provide a flexible and elastomeric waterproof Elongation ASTM D412
membrane upon curing. ≥15 %
@ 14 days
2
Compressive Strength ≥30 N/mm @ 3 days
Properties ASTM C109 2
≥35 N/mm @ 28 days
 Two components system. 2
Flexural Strength BS ≥3.5 N/mm @ 3 days
 Easy to mix and use. EN196-1 2
≥5 N/mm @ 28 days
 Exhibits a good water vapour Linear Coefficient of
-6
transmission- Breathable substrate. thermal expansion Approx. 9.65*10 /ºC
 Non-flammable and Nontoxic. ASTM C531
 Negligible volatile organic compounds Pull off bond Strength
≥1 Mpa
 Flexible and elastomeric waterproof ASTM D7234 @ 14 days
membrane. VOC (EPA 24) < 10 g/L
 Excellent bond strength. Water Vapour
 Crack bridging ability. Transmission ASTM E96 Approx. 32.6 g/m .24h
2

 Resistance to fungal growth. (2mm DFT)

 Capable to withstand positive and Water penetration BS EN
negative hypostatic pressure. Nil
12390-8(5 bar; 2 mm DFT)
 Resistant to roots penetration
Coverage
Application area 25kg kit of CIKOproof 2K-25 yield to 11.5-12 L and
2
CIKOproof 2K-25 is a high quality cementitious provide coverage 11.5 to 12 m @1mm Thickness.
waterproof membrane coating that can be Note: Coverage rate may vary depending on substrate
used for interior or exterior applications. condition and type.
 Masonry wall, concrete and plaster Required total dry film thickness applied in two coats
surface. ranges from minimum 1.5 mm up to 3mm depending on
 Damp proofing in sub and super intended to use location and service life. Consult CIKO
structures. technical service department for further support.
 Basements and pits.
 Wet areas waterproofing.

1
Application instructions Packaging
Surface preparation CIKOproof 2K-25 is available in 25kg kit consisting of
The concrete or cement substrate shall be free [Part-A] 20kg powder and [Part-B] 5 kg liquid.
from all loosely adhered particles, Shelf Life
efflorescence, dust, oil, grease or any other CIKOproof 2K-25 has a shelf life of 12 months in un-
contamination. In case of oil spillage, proper opened bags and if stored in accordance with CIKO
treatment should be carried out on the surface. instructions.
After ensuring sound substrate, dampen the Storage
surface with water just before the application of CIKOproof 2K-25 should be stored under enclosed
CIKOproof 2K-25. Wherever cracks, voids, shaded area at an ambient temperature between 5 ºC to
honeycombs, etc. are presents, the surface 40 ºC.
must be repaired using CIKO wide variety of Precautions
repairs materials. (Refer to CIKO technical
 Do not apply over standing water.
team for more details).
 Do not proceed with application if the ambient
Mixing temperature is below 8 ºC and above 40 ºC.
Liquid component of CIKOproof 2K-25 [Part-B]  Do not re-temper the mixed material after initial
should be mixed with powder component [Part- mixing.
A] using heavy duty slow speed drill-paddle  Re-Mixing every 15-20 minutes within the 60
assembly. The properly mixed material should minutes pot life is advisable.
be lump free. It is recommended to pour the  It is recommended to use CIKObond PVA as a
powder part partially while mixing to achieve sealer on lightweight blocks, gypsum and dry
proper consistency free of lump. It is applicable substrates having high porosity.
to use 80 to 90 % of the liquid quantity [Part-B]  Allow to cure for at least 3 days prior to service.
used in mixing to achieve a trowable
consistency if required. Health & safety
Application method Use standard dust mask to avoid inhalation of dust.
The mixed material should apply on the Powder when wet or moist can cause burns to skin and
cleaned and damped surface using brush, or eyes which should be protected during use. If comes in
steel trowel at the rate of 1.5 kg up to 3 kg per contact with eyes, flush with plenty of fresh water and
coat. Do not apply the material on standing seek medical advice.
water. Sponge can be used to get rid of Refer Material Safety Data Sheet for further details.
standing water or re damp the dried areas.
Care should be taken to coat the surface
without leaving any gap. The second coat must Technical Support
be applied in cross direction to the first coat at For any technical support, do not hesitate to contact
the same rate of consumption and depending CIKO team at any time as CIKO offers on and off site
on the required total DFT. Time gap in over- services to end users, specifier and contractors.
coating depends on ambient temperature,
which ranges between 2 and 6 hours. The first More from CIKO Middle East
coat must be dry and not affected by feet
A wide range of construction chemical products are
traffic. Protect the applied area from direct sun
light, wind rain and frost. manufactured by CIKO Middle East which includes:
At right angles, static repaired cracks, patched  Concrete admixtures and additives
areas and wall to floor transitions, pipe  Waterproofing and damp proof coatings
penetrations and floor drains; it is  Surface treatments
recommended to embed a fibre mesh  Flooring and toppings
sandwich between the coatings. To do so,  Grouts and anchors
immediately after the application of the first
 Tile adhesives and grout
coat, embed the fibre mesh by exerting force
using a steel trowel, brush or any suitable tool.  Concrete repair materials
The required total dry film thickness of  Adhesives and bonding agent
CIKOproof 2k-25 depends on the application  Protective coating
area; intended to use location and required  Joint Sealants and Moulding compounds
service life.  Ancillaries

TDS/WP20 Rev.:2 Issue:C

Note: The information presented herein based on the best of our knowledge and expertise for which every effort is made to ensure its
reliability. Although all the products are subjected to rigid quality tests and are guaranteed against defective materials and manufacture,
no specific guarantee can be extended because results depend not only on quality but also on other factors beyond our control